 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| EVERLIGHT ELECTRONICS CO., LTD. Technical Data Sheet 0805 Package Chip LED (1.1mm Height) 17-21/R7C-AN2Q1B/3T Features Package in 8mm tape on 7diameter reel. Compatible with automatic placement equipment. Compatible with infrared and vapor phase reflow solder process. Mono-color type. Pb-free Descriptions The 17-21 SMD Taping is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. Besides, lightweight makes them ideal for miniature applications, etc. Applications Automotive: backlighting in dashboard and switch. Telecommunication: indicator and backlighting in telephone and fax. Flat backlight for LCD, switch and symbol. General use. Device Selection Guide Chip Material AlGaInP Emitted Color Dark Red PART No. 17-21/R7C-AN1P2B/3T Lens Color Water Clear Everlight Electronics Co., Ltd. Device No: SZDSE-171-R03 http://www.everlight.com Prepared date: 25-Jan-2005 Rev.: 1 Page: 1 of 10 Prepared by: Huadong DEN EVERLIGHT ELECTRONICS CO., LTD. 17-21/R7C-AN2Q1B/3T Package Outline Dimensions - + Note: The tolerances unless mentioned are 0.1, unit = mm. Everlight Electronics Co., Ltd. Device No: SZDSE-171-R03 http://www.everlight.com Prepared date: 25-Jan-2005 Rev.: 1 Page: 2 of 10 Prepared by: Huadong DEN EVERLIGHT ELECTRONICS CO., LTD. 17-21/R7C-AN2Q1B/3T Absolute Maximum Ratings (Ta=25) Parameter Reverse Voltage Forward Current Operating Temperature Storage Temperature Soldering Temperature Electrostatic Discharge Power Dissipation Peak Forward Current (Duty 1/10 @1KHz) Symbol VR IF Topr Tstg Tsol ESD Pd IFP Rating 5 25 -40 ~ +85 -40~ +90 260 (for 5 seconds) 2000 60 60 Unit V mA V mW mA Electro-Optical Characteristics (Ta=25) Parameter Luminous Intensity Viewing Angle Peak Wavelength Dominant Wavelength Symbol Iv 21/2 p d VF IR Min. 36.0 --------629.5 ----1.75 ----- Typ. ----140 639 ---20 --------- Max. 90.0 --------645.5 ----2.35 10 Unit mcd deg nm nm nm V A Condition IF=20 mA Spectrum Radiation Bandwidth Forward Voltage Reverse Current VR=5V Notes: 1.Tolerance of Luminous Intensity 10% 2.Tolerance of Dominant Wavelength 1nm 3.Tolerance of Forward Voltage 0.1V Everlight Electronics Co., Ltd. Device No: SZDSE-171-R03 http://www.everlight.com Prepared date: 25-Jan-2005 Rev.: 1 Page: 3 of 10 Prepared by: Huadong DEN EVERLIGHT ELECTRONICS CO., LTD. 17-21/R7C-AN2Q1B/3T Bin Range Of Dom. Wavelength Group Bin E7 A E8 E9 E10 Min 629.5 633.5 637.5 641.5 Max 633.5 637.5 641.5 645.5 nm IF=20mA Unit Condition Bin Range Of Luminous Intensity Bin N2 P1 P2 Q1 Min 36.0 45.0 57.0 72.0 Max 45.0 57.0 72.0 90.0 mcd IF=20mA Unit Condition Bin Range Of Forward Voltage Groups B Bin 0 1 2 Min 1.75 1.95 2.15 Max 1.95 2.15 2.35 V IF=20mA Unit Condition Notes: 1.Tolerance of Luminous Intensity 10% 2.Tolerance of Dominant Wavelength 1nm 3.Tolerance of Forward Voltage 0.1V Everlight Electronics Co., Ltd. Device No: SZDSE-171-R03 http://www.everlight.com Prepared date: 25-Jan-2005 Rev.: 1 Page: 4 of 10 Prepared by: Huadong DEN EVERLIGHT ELECTRONICS CO., LTD. 17-21/R7C-AN2Q1B/3T Typical Electro-Optical Characteristics Curves Everlight Electronics Co., Ltd. Device No: SZDSE-171-R03 http://www.everlight.com Prepared date: 25-Jan-2005 Rev.: 1 Page: 5 of 10 Prepared by: Huadong DEN EVERLIGHT ELECTRONICS CO., LTD. 17-21/R7C-AN2Q1B/3T Label explanation CAT: Luminous Intensity Rank HUE: Dom. Wavelength Rank REF: Forward Voltage Rank Reel Dimensions Note: The tolerances unless mentioned are 0.1, unit = mm. Everlight Electronics Co., Ltd. Device No: SZDSE-171-R03 http://www.everlight.com Prepared date: 25-Jan-2005 Rev.: 1 Page: 6 of 10 Prepared by: Huadong DEN EVERLIGHT ELECTRONICS CO., LTD. 17-21/R7C-AN2Q1B/3T Carrier Tape Dimensions: Loaded quantity 3000 PCS per reel Note: The tolerances unless mentioned are 0.1, unit = mm. Moisture Resistant Packaging Label Aluminum moisture-proof bag Desiccant Label Everlight Electronics Co., Ltd. Device No: SZDSE-171-R03 http://www.everlight.com Prepared date: 25-Jan-2005 Rev.: 1 Page: 7 of 10 Prepared by: Huadong DEN EVERLIGHT ELECTRONICS CO., LTD. 17-21/R7C-AN2Q1B/3T Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level : 90 % LTPD : 10 % Test Sample No. Items Test Condition Hours/Cycles Size Temp. : 2605 6 min. 1 Reflow Soldering 22 Pcs. Min.5 sec. H : +100 15min. 300 Cycles 2 Temperature Cycle 22 Pcs. 5 min. L : -40 15min. 3 Thermal Shock High Temperature Storage Low Temperature Storage DC Operating Life High Temperature / High Humidity H : +100 5min. 10 sec. L : -10 5min. Temp. : 100 Temp. : -40 IF = 20 mA 85/ 85% R.H. 300 Cycles 1000 Hrs. 1000 Hrs. 1000 Hrs. 1000 Hrs. 22 Pcs. Ac/Re 0/1 0/1 0/1 4 5 6 7 22 Pcs. 22 Pcs. 22 Pcs. 22 Pcs. 0/1 0/1 0/1 0/1 Everlight Electronics Co., Ltd. Device No: SZDSE-171-R03 http://www.everlight.com Prepared date: 25-Jan-2005 Rev.: 1 Page: 8 of 10 Prepared by: Huadong DEN EVERLIGHT ELECTRONICS CO., LTD. 17-21/R7C-AN2Q1B/3T Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30 or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30 or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 605 for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. 4. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 280 for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. Everlight Electronics Co., Ltd. Device No: SZDSE-171-R03 http://www.everlight.com Prepared date: 25-Jan-2005 Rev.: 1 Page: 9 of 10 Prepared by: Huadong DEN EVERLIGHT ELECTRONICS CO., LTD. 17-21/R7C-AN2Q1B/3T 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com Everlight Electronics Co., Ltd. Device No: SZDSE-171-R03 http://www.everlight.com Prepared date: 25-Jan-2005 Rev.: 1 Page: 10 of 10 Prepared by: Huadong DEN |
Price & Availability of 17-21-R7C-AN2Q1B-3T
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |