 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| HIGH NOISE REDUCTION/ HIGH SPEED 10 Mbps, TOTEM-POLE OUTPUT TYPE PS9711 5 PIN SOP TOM OPTOCOUPLER FEATURES * HIGH COMMON MODE TRANSIENT IMMUNITY CMH, CML: 10 kV/s TYP * SMALL PACKAGE 5 pin SOP * HIGH SPEED RESPONSE tPHL = 30 ns, tPLH = 35 ns TYP * PULSE WIDTH DISTORTION |tPHL-tPLH| = 7 ns TYP * TOTEM-POLE OUTPUT No Pull-up resistor required * TAPE AND REEL AVAILABLE DESCRIPTION The PS9711 is an optically coupled high speed totem pole isolator containing a GaAIAs LED on the light emitting diode side (input side) and a photodiode and a signal processing circuit on the light receiving side (output side) on one chip. It is housed in a plastic SOP (Small Out-Line Package) for high density applications. APPLICATIONS * COMPUTER AND PERIPHERAL DEVICES * MEASUREMENT EQUIPMENT * POWER SUPPLY ELECTRICAL CHARACTERISTICS (TA = -40 to +85 C, unless otherwise specified) PART NUMBER SYMBOLS PARAMETERS Forward Voltage, IF = 10 mA, TA = 25C Reverse Current, VR = 3 V, TA = 25C Capacitance, V = 0, f = 1.0 MHz, TA = 25C High Level Output Current, VCC = VO = 5.5 V, IF = 250 A High Level Output Voltage, VCC = 4.5 V, IF = 250 A, IOH = -2 mA Low Level Output Voltage, VCC = 4.5 V, IF = 7 mA, IO = 8 mA High Level Supply Current, VCC = 5.5 V, IF = 0 mA Low Level Supply Current, VCC = 5.5 V, IF = 10 mA High Level Output Short Circuit Current, VCC = 5.5 V, VO =GND, IF = 0 mA, 10 ms or less Low Level Output Short Circuit Current, VCC = 5.5 V, VO =GND, IF = 8 mA, 10 ms or less Threshold Input Current, High Low, VCC = 5 V Threshold Input Current, Low High, VCC = 5 V TA = 25C TA = 25C UNITS V A pF A V V mA mA mA mA mA mA pF ns ns ns kV/s kV/s 1 1 15 10 15 10 7 10 10 0.5 0.35 1011 0.6 30 35 65 85 65 85 35 2.4 30 1 3.0 0.38 11 12 -26 34 2.0 5 6 0.6 17 18 200 MIN 1.4 VF IR Ct IOH VOH PS9711 TYP 1.65 MAX 1.9 10 Detector Diode VOL ICCH ICCL IOSH IOSL IFHL IFLH Coupled RI-O CI-O tPHL tPLH |tPHL-tPLH| CMH CML Isolation Resistance, Vin-out = 1 kVDC, RH = 40 to 60%, TA = 25C Isolation Capacitance, V = 0, f = 1.0 MHz, TA = 25C Propagation Delay Time, High Low2 , VCC = 5 V, IF = 7.5 mA TA = 25C TA = 25C Pulse Width Distortion, (PWD)2,VCC = 5 V, IF = 7.5 mA Common Mode Transient Immunity at High Level Output3 VCC = 5 V, TA = 25C, IF = 0 mA, VO(min) = 2 V , VCM = 100 V Common Mode Transient Immunity at Low Level Output3 VCC = 5 V, TA = 25C, IF = 7.5 mA, VO = 0.8 V (max) RL = 350 VCM = 1 kV Propagation Delay Time, Low High2 ,VCC = 5 V, IF = 7.5 mA SEE NOTES ON NEXT PAGE California Eastern Laboratories PS9711 ELECTRICAL CHARACTERISTICS NOTES: 1. Typical Values at TA = 25C. 2. Test Circuit for Propagation Delay Time: VCC = 5 V VCC = 5 V Input IF (ON) 50% IF (ON) Pulse Input (IF) VO (Monitor) 1.3 k ( PW = 500 ns Duty Cycle = 1/2 ) VCC 0.1 F VON Output 1.5 V VOL tPHL tPLH Input Monitor CL = 15 pF 47 GND *CL = 30pF 2.5 k CL is approximately 15 pF, which includes probe and stray wiring capacitance. 3. Test Circuit for Common Mode Transient Immunity VCC = 5 V GL SW IF VCM 90% VCC 0.1 F VO (Monitor) CL = 15pF GND 100 V 0V tf VOH 2V 0.8 V VOL 10% tr VO IF = 0 mA VO IF = 7.5 mA CL is approximately 15 pF, which includes probe and stray wiring capacitance. USAGE CAUTIONS 1. Protect against static electricity when handling. 2. By-pass capacitor of more than 0.1 F is used between VCC and GND near device. RECOMMENDED OPERATING CONDITIONS PART NUMBER PS9711 UNITS MIN TYP MAX mA A V TTL 7.5 0 4.5 5.0 12.5 250 5.5 3 SYMBOLS IFH IFL VCC N PARAMETERS High Level Input Current Low Level Input Current Supply Voltage TTL RL = 1 k ABSOLUTE MAXIMUM RATINGS1 (TA = 25C) SYMBOLS Diode VR IF Detector VCC VO IOH IOL PD Coupled BV TSTG TA PARAMETERS Reverse Voltage Forward Current (DC) Supply Voltage Output Voltage High Level Output Current2 Low Level Output Current2 Power Dissipation Isolation Voltage3 Storage Temperature Operating Temperature UNITS V mA V V mA mA mW Vr.m.s. C C RATINGS 3.0 30 7 7 -5 13 130 2500 -55 to +125 -40 to +85 ORDERING INFORMATION PART NUMBER PS9711 PS9711-E3 PS9711-E4 PS9711-F3 PS9711-F4 Embossed Tape 3500 pcs/reel PACKAGE 5 Pin SOP PACKING STYLE Magazine case 100 pcs Embossed Tape 900 pcs/reel Notes: 1. Operaion in excess of any one of these parameters may result in permanent damage. 2. TA = -40 to +85C. 3. AC voltage for 1 minute at TA = 25 C, RH = 60 % between input and output. PS9711 OUTLINE DIMENSIONS (Units in mm) PS9711 4.00.5 PIN CONNECTION (Top View) 5 4 3 1. 2. 3. 4. 5. 1 0.4 -0.05 +0.10 Anode Cathode GND VO VCC 2 0.25 M 7.0 0.3 4.4 2.10.2 INTERNAL OUTPUT CIRCUIT 1.3 VCC (5) +0.10 0.15 -0.05 0.1 0.1 1.27 1.2 MAX 0.5 0.3 LED ON VO (4) OUTPUT L H OFF GND (3) TYPICAL PERFORMANCE CURVES (TA = 25C unless otherwise specified) MAXIMUM FORWARD CURRENT vs. AMBIENT TEMPERATURE 40 DETECTOR POWER DISSIPATION vs. AMBIENT TEMPERATURE 200 Detector Power Dissipation, Pc (mW) 80 85 Maximum Forward Current, IF (mA) 30 150 20 100 10 50 0 20 40 60 100 0 20 40 60 80 85 100 Ambient Temperature, TA (C) FORWARD CURRENT vs. FORWARD VOLTAGE 100 Ambient Temperature, TA (C) SUPPLY CURRENT vs. AMBIENT TEMPERATURE 20 High Level Supply Current, ICCH (mA) Low Level Supply Current, ICCL (mA) 18 16 14 VCC = 5.5 V, ICCH: IF = 0 mA ICCL: IF = 10 mA Forward Current IF (mA) 10 ICCL 12 10 8 6 4 2 0 -50 -25 0 25 50 75 100 ICCH 1.0 TA = 100 C 50 C 25 C 0 C -25 C 0.1 0.01 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 Forward Voltage, VF (V) Ambient Temperature, TA (C) PS9711 TYPICAL PERFORMANCE CURVES (TA = 25C unless otherwise specified) HIGH LEVEL OUTPUT VOLTAGE vs. HIGH LEVEL OUTPUT CURRENT 5 5 VCC = 4.5 V, IF = 250 A VCC = 4.5 V, IF = 250 A, IOH = -2 mA HIGH LEVEL OUTPUT VOLTAGE vs. AMBIENT TEMPERATURE High Level Output Voltage, VOH (V) High Level Output Voltage, VOH (V) 4 TA = +85C +25C -40C 4 3 3 2 2 1 1 0 0 -1 -2 -3 -4 -5 -6 0 -50 -25 0 25 50 75 100 High Level Output Current IOH (mA) Ambient Temperature, TA (C) LOW LEVEL OUTPUT VOLTAGE vs. LOW LEVEL OUTPUT CURRENT 3 VCC = 4.5 IF = 7 mA 1.0 0.9 LOW LEVEL OUTPUT VOLTAGE vs. AMBIENT TEMPERATURE VCC = 4.5 V, IF = 7 mA, IO = 8 mA Low Level Output Voltage, VOH (V) Low Level Output Voltage, VOH (V) 10 15 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 -50 -25 0 25 50 75 100 2 TA = +85C 1 +25C -40C 0 5 Low Level Output Current IOH (mA) PROPAGATION DELAY TIME, PULSE WIDTH DISTORTION vs. FORWARD CURRENT 70 VCC = 5 V Ambient Temperature, TA (C) PROPAGATION DELAY TIME, PULSE WIDTH DISTORTION vs. AMBIENT TEMPERATURE 70 Propagation Delay Time, tPHL, tPLH (ns) Pulse Width Distortion, |tPHL - tPLH| (ns) 60 50 40 30 20 10 0 -10 -20 -30 0 5 10 15 20 25 PWD Propagation Delay Time, tPHL, tPLH (ns) Pulse Width Distortion, |tPHL - tPLH| (ns) VCC = 5 V, IF = 7.5 mA 60 50 tPLH tPLH 40 tPHL tPHL 30 20 10 0 -50 -25 0 25 50 PWD 75 100 Forward Current, IF (mA) Ambient Temperature, TA (C) PS9711 TYPICAL PERFORMANCE CURVES (TA = 25C unless otherwise specified) THRESHOLD INPUT CURRENT vs. AMBIENT TEMPERATURE Threshold Input Current, IFHL, IFLH (mA) 8 VCC = 5 V 7 6 5 4 3 IFHL 2 IFLH 1 0 -50 -25 0 25 50 75 100 Ambient Temperature, TA (C) TAPING SPECIFICATIONS (Units in mm) TAPE OUTLINE AND DIMENSIONS 40.1 20.1 1.550.1 1.750.1 TAPE DIRECTION PS9711-E3 PS9711-E4 2.40.1 5.50.1 120.2 1.550.1 80.1 4.60.1 0.3 7.40.1 REEL OUTLINE AND DIMENSIONS 2.0 2.00.5 15 15 21.00.8 13.00.5 13.00.5 180 60 Packing: 900 pcs/reel 13.01.0 PS9711 TAPING SPECIFICATIONS (Units in mm) TAPE OUTLINE AND DIMENSIONS 40.1 20.1 1.550.1 1.750.1 TAPE DIRECTION PS9711-F3 2.40.1 5.50.1 120.2 PS9711-F4 1.550.1 80.1 4.60.1 0.3 7.40.1 REEL OUTLINE AND DIMENSIONS 1.5 0.1 1.5 0.1 12 21.0 0.8 0 PS89701-E3, E4: 178 PS9701-F3, F4: 330 2.0 0.5 1.5 0.5 60 6.0 1 13.00.5 66 Packing: 3500 pcs/reel 12.4 -0.0 +2.0 18.4 MAX PS9711 RECOMMENDED SOLDERING CONDITIONS (1) Infrared reflow soldering * Peak reflow temperature * Time of temperature higher than 210 C * Number of reflows * Flux 235 C or below (package surface temperature) 30 seconds or less Three Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt % is recommended). Package Surface Temperature T (C) (heating) to 10 s 235 C (peak temperature) 210 C to 30 s 100 to 160 C 60 to 120 s (preheating) Time (s) (2) Dip soldering * Temperature * Time * Number of times * Flux 260 C or below (molten solder temperature) 10 seconds or less One (Allowed to be dipped in solder including plastic mold portion.) Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt % is recommended). (3) Cautions * Fluxes Avoid removing the residual flux with chlorine-based cleaning solvent after a reflow process. Life Support Applications These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and agree to fully indemnify CEL for all damages resulting from such improper use or sale. 03/17/2003 A Business Partner of NEC Compound Semiconductor Devices, Ltd. |
Price & Availability of PS9711
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |