|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
16 H8/36912 Group, H8/36902 Group Hardware Manual Renesas 16-Bit Single-Chip Microcomputer H8 Family/H8/300H Tiny Series H8/36912F H8/36902F H8/36912 H8/36911 H8/36902 H8/36901 H8/36900 HD64F36912G HD64F36902G HD64336912G HD64336911G HD64336902G HD64336901G HD64336900G Rev.1.00 2003.11.7 Rev. 1.00, 11/03, page ii of xxviii Cautions Keep safety first in your circuit designs! 1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap. Notes regarding these materials 1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or a third party. 2. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples contained in these materials. 3. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of publication of these materials, and are subject to change by Renesas Technology Corp. without notice due to product improvements or other reasons. It is therefore recommended that customers contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor for the latest product information before purchasing a product listed herein. The information described here may contain technical inaccuracies or typographical errors. Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information published by Renesas Technology Corp. by various means, including the Renesas Technology Corp. Semiconductor home page (http://www.renesas.com). 4. When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and products. Renesas Technology Corp. assumes no responsibility for any damage, liability or other loss resulting from the information contained herein. 5. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use. 6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials. 7. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited. 8. Please contact Renesas Technology Corp. for further details on these materials or the products contained therein. Rev. 1.00, 11/03, page iii of xxviii General Precautions on Handling of Product 1. Treatment of NC Pins Note: Do not connect anything to the NC pins. The NC (not connected) pins are either not connected to any of the internal circuitry or are used as test pins or to reduce noise. If something is connected to the NC pins, the operation of the LSI is not guaranteed. 2. Treatment of Unused Input Pins Note: Fix all unused input pins to high or low level. Generally, the input pins of CMOS products are high-impedance input pins. If unused pins are in their open states, intermediate levels are induced by noise in the vicinity, a passthrough current flows internally, and a malfunction may occur. 3. Processing before Initialization Note: When power is first supplied, the product's state is undefined. The states of internal circuits are undefined until full power is supplied throughout the chip and a low level is input on the reset pin. During the period where the states are undefined, the register settings and the output state of each pin are also undefined. Design your system so that it does not malfunction because of processing while it is in this undefined state. For those products which have a reset function, reset the LSI immediately after the power supply has been turned on. 4. Prohibition of Access to Undefined or Reserved Addresses Note: Access to undefined or reserved addresses is prohibited. The undefined or reserved addresses may be used to expand functions, or test registers may have been be allocated to these addresses. Do not access these registers; the system's operation is not guaranteed if they are accessed. Rev. 1.00, 11/03, page iv of xxviii Configuration of This Manual This manual comprises the following items: 1. General Precautions on Handling of Product 2. Configuration of This Manual 3. Preface 4. Contents 5. Overview 6. Description of Functional Modules * * CPU and System-Control Modules On-Chip Peripheral Modules The configuration of the functional description of each module differs according to the module. However, the generic style includes the following items: i) Feature ii) Input/Output Pin iii) Register Description iv) Operation v) Usage Note When designing an application system that includes this LSI, take notes into account. Each section includes notes in relation to the descriptions given, and usage notes are given, as required, as the final part of each section. 7. List of Registers 8. Electrical Characteristics 9. Appendix 10. Main Revisions and Additions in this Edition (only for revised versions) The list of revisions is a summary of points that have been revised or added to earlier versions. This does not include all of the revised contents. For details, see the actual locations in this manual. 11. Index Rev. 1.00, 11/03, page v of xxviii Preface The H8/36912 Group and H8/36902 Group are single-chip microcomputers made up of the highspeed H8/300H CPU employing Renesas Technology original architecture as their cores, and the peripheral functions required to configure a system. The H8/300H CPU has an instruction set that is compatible with the H8/300 CPU. Target Users: This manual was written for users who will be using the H8/36912 Group and H8/36902 Group in the design of application systems. Target users are expected to understand the fundamentals of electrical circuits, logical circuits, and microcomputers. Objective: This manual was written to explain the hardware functions and electrical characteristics of the H8/36912 Group and H8/36902 Group to the target users. Refer to the H8/300H Series Programming Manual for a detailed description of the instruction set. Notes on reading this manual: * In order to understand the overall functions of the chip Read the manual according to the contents. This manual can be roughly categorized into parts on the CPU, system control functions, peripheral functions and electrical characteristics. * In order to understand the details of the CPU's functions Read the H8/300H Series Programming Manual. * In order to understand the details of a register when its name is known Read the index that is the final part of the manual to find the page number of the entry on the register. The addresses, bits, and initial values of the registers are summarized in section 19, List of Registers. Example: Notes: When using an on-chip emulator (E7) for H8/36912, H8/36902 program development and debugging, the following restrictions must be noted. 1. The NMI pin is reserved for the E7, and cannot be used. 2. Area H'2000 to H'2FFF is used by the E7, and is not available to the user. 3. Area H'F980 to H'FD7F must on no account be accessed. 4. When the E7 is used, address breaks can be set as either available to the user or for use by the E7. If address breaks are set as being used by the E7, the address break control registers must not be accessed. 5. When the E7 is used, NMI is an input/output pin (open-drain in output mode). Rev. 1.00, 11/03, page vi of xxviii Bit order: The MSB is on the left and the LSB is on the right. Related Manuals: The latest versions of all related manuals are available from our web site. Please ensure you have the latest versions of all documents you require. http://www.renesas.com/eng/ H8/36912 Group and H8/36902 Group manuals: Document Title H8/36912 Group, H8/36902 Group Hardware Manual H8/300H Series Programming Manual Document No. This manual ADE-602-053 User's manuals for development tools: Document Title H8S, H8/300 Series C/C++ Compiler, Assembler, Optimizing Linkage Editor User's Manual H8S, H8/300 Series Simulator/Debugger User's Manual H8S, H8/300 Series High-Performance Embedded Workshop, High-Performance Debugging Interface Tutorial High-Performance Embedded Workshop User's Manual Document No. ADE-702-247 ADE-702-282 ADE-702-231 ADE-702-201 Application notes: Document Title Single Power Supply F-ZTAT TM Document No. On-Board Programming ADE-502-055 Rev. 1.00, 11/03, page vii of xxviii Rev. 1.00, 11/03, page viii of xxviii Contents Section 1 Overview........................................................................................... 1 1.1 1.2 1.3 1.4 Features .............................................................................................................................1 Internal Block Diagram.....................................................................................................3 Pin Arrangement ...............................................................................................................5 Pin Functions.....................................................................................................................9 Section 2 CPU................................................................................................... 11 2.1 2.2 Address Space and Memory Map .....................................................................................12 Register Configuration ......................................................................................................14 2.2.1 General Registers .................................................................................................15 2.2.2 Program Counter (PC) .........................................................................................16 2.2.3 Condition-Code Register (CCR) ..........................................................................16 Data Formats .....................................................................................................................18 2.3.1 General Register Data Formats ............................................................................18 2.3.2 Memory Data Formats .........................................................................................20 Instruction Set ...................................................................................................................21 2.4.1 Table of Instructions Classified by Function .......................................................21 2.4.2 Basic Instruction Formats ....................................................................................30 Addressing Modes and Effective Address Calculation .....................................................31 2.5.1 Addressing Modes ...............................................................................................31 2.5.2 Effective Address Calculation..............................................................................34 Basic Bus Cycle ................................................................................................................36 2.6.1 Access to On-Chip Memory (RAM, ROM).........................................................36 2.6.2 On-Chip Peripheral Modules ...............................................................................37 CPU States ........................................................................................................................38 Usage Notes ......................................................................................................................39 2.8.1 Notes on Data Access to Empty Areas.................................................................39 2.8.2 EEPMOV Instruction...........................................................................................39 2.8.3 Bit Manipulation Instruction ................................................................................39 2.3 2.4 2.5 2.6 2.7 2.8 Section 3 Exception Handling .......................................................................... 45 3.1 3.2 Exception Sources and Vector Address ............................................................................45 Register Descriptions ........................................................................................................47 3.2.1 Interrupt Edge Select Register 1 (IEGR1)............................................................47 3.2.2 Interrupt Edge Select Register 2 (IEGR2)............................................................48 3.2.3 Interrupt Enable Register 1 (IENR1) ...................................................................48 3.2.4 Interrupt Enable Register 2 (IENR2) ...................................................................49 3.2.5 Interrupt Flag Register 1 (IRR1) ..........................................................................50 3.2.6 Interrupt Flag Register 2 (IRR2) ..........................................................................51 Rev. 1.00, 11/03, page ix of xxviii 3.3 3.4 3.5 3.2.7 Wakeup Interrupt Flag Register (IWPR) ............................................................. 51 Reset Exception Handling................................................................................................. 52 Interrupt Exception Handling............................................................................................ 53 3.4.1 External Interrupts ............................................................................................... 53 3.4.2 Internal Interrupts................................................................................................. 54 3.4.3 Interrupt Handling Sequence ............................................................................... 54 3.4.4 Interrupt Response Time...................................................................................... 56 Usage Notes ...................................................................................................................... 58 3.5.1 Interrupts after Reset............................................................................................ 58 3.5.2 Notes on Stack Area Use ..................................................................................... 58 3.5.3 Notes on Rewriting Port Mode Registers............................................................. 58 Section 4 Address Break....................................................................................59 4.1 Register Descriptions ........................................................................................................ 59 4.1.1 Address Break Control Register (ABRKCR)....................................................... 60 4.1.2 Address Break Status Register (ABRKSR) ......................................................... 61 4.1.3 Break Address Registers (BARH, BARL)........................................................... 62 4.1.4 Break Data Registers (BDRH, BDRL) ................................................................ 62 Operation .......................................................................................................................... 63 4.2 Section 5 Clock Pulse Generators .....................................................................65 5.1 5.2 Features ............................................................................................................................. 66 Register Descriptions ........................................................................................................ 67 5.2.1 RC Control Register (RCCR) .............................................................................. 67 5.2.2 RC Trimming Data Protect Register (RCTRMDPR)........................................... 68 5.2.3 RC Trimming Data Register (RCTRMDR) ......................................................... 69 5.2.4 Clock Control/Status Register (CKCSR) ............................................................. 69 System Clock Select Operation......................................................................................... 71 5.3.1 Clock Control Operation...................................................................................... 72 5.3.2 Clock Change Timing .......................................................................................... 75 Trimming of Internal RC Oscillator Frequency ................................................................ 78 External Oscillators........................................................................................................... 80 5.5.1 Connecting Crystal Resonator ............................................................................. 80 5.5.2 Connecting Ceramic Resonator ........................................................................... 81 5.5.3 External Clock Input Method............................................................................... 81 Prescaler............................................................................................................................ 81 5.6.1 Prescaler S ........................................................................................................... 81 Usage Notes ...................................................................................................................... 82 5.7.1 Note on Resonators .............................................................................................. 82 5.7.2 Notes on Board Design ........................................................................................ 82 5.3 5.4 5.5 5.6 5.7 Rev. 1.00, 11/03, page x of xxviii Section 6 Power-Down Modes ......................................................................... 83 6.1 Register Descriptions ........................................................................................................84 6.1.1 System Control Register 1 (SYSCR1) .................................................................84 6.1.2 System Control Register 2 (SYSCR2) .................................................................86 6.1.3 Module Standby Control Register 1 (MSTCR1)..................................................87 6.1.4 Module Standby Control Register 2 (MSTCR2)..................................................88 Mode Transitions and States of LSI ..................................................................................89 6.2.1 Sleep Mode ..........................................................................................................90 6.2.2 Standby Mode ......................................................................................................91 6.2.3 Subsleep Mode.....................................................................................................91 Operating Frequency in Active Mode ...............................................................................92 Direct Transition ...............................................................................................................92 Module Standby Function .................................................................................................92 6.2 6.3 6.4 6.5 Section 7 ROM ................................................................................................. 93 7.1 7.2 Block Configuration..........................................................................................................94 Register Descriptions ........................................................................................................96 7.2.1 Flash Memory Control Register 1 (FLMCR1).....................................................96 7.2.2 Flash Memory Control Register 2 (FLMCR2).....................................................97 7.2.3 Erase Block Register 1 (EBR1) ...........................................................................98 7.2.4 Flash Memory Enable Register (FENR) ..............................................................98 On-Board Programming Modes ........................................................................................99 7.3.1 Boot Mode ...........................................................................................................99 7.3.2 Programming/Erasing in User Program Mode.....................................................102 Flash Memory Programming/Erasing ...............................................................................103 7.4.1 Program/Program-Verify .....................................................................................103 7.4.2 Erase/Erase-Verify ...............................................................................................105 7.4.3 Interrupt Handling when Programming/Erasing Flash Memory..........................106 Program/Erase Protection..................................................................................................108 7.5.1 Hardware Protection ............................................................................................108 7.5.2 Software Protection..............................................................................................108 7.5.3 Error Protection....................................................................................................108 7.3 7.4 7.5 Section 8 RAM ................................................................................................. 109 Section 9 I/O Ports ............................................................................................ 111 9.1 Port 1.................................................................................................................................111 9.1.1 Port Mode Register 1 (PMR1) .............................................................................112 9.1.2 Port Control Register 1 (PCR1) ...........................................................................113 9.1.3 Port Data Register 1 (PDR1)................................................................................113 9.1.4 Port Pull-Up Control Register 1 (PUCR1)...........................................................114 9.1.5 Pin Functions .......................................................................................................114 Rev. 1.00, 11/03, page xi of xxviii 9.2 9.3 9.4 9.5 9.6 9.7 Port 2................................................................................................................................. 115 9.2.1 Port Control Register 2 (PCR2) ........................................................................... 115 9.2.2 Port Data Register 2 (PDR2)................................................................................ 116 9.2.3 Pin Functions ....................................................................................................... 116 Port 5................................................................................................................................. 117 9.3.1 Port Mode Register 5 (PMR5) ............................................................................. 118 9.3.2 Port Control Register 5 (PCR5) ........................................................................... 118 9.3.3 Port Data Register 5 (PDR5)................................................................................ 119 9.3.4 Port Pull-Up Control Register 5 (PUCR5)........................................................... 119 9.3.5 Pin Functions ....................................................................................................... 120 Port 7................................................................................................................................. 121 9.4.1 Port Control Register 7 (PCR7) ........................................................................... 121 9.4.2 Port Data Register 7 (PDR7)................................................................................ 122 9.4.3 Pin Functions ....................................................................................................... 122 Port 8................................................................................................................................. 123 9.5.1 Port Control Register 8 (PCR8) ........................................................................... 124 9.5.2 Port Data Register 8 (PDR8)................................................................................ 124 9.5.3 Pin Functions ....................................................................................................... 125 Port B ................................................................................................................................ 127 9.6.1 Port Data Register B (PDRB) .............................................................................. 127 9.6.2 Pin Functions ....................................................................................................... 128 Port C ................................................................................................................................ 130 9.7.1 Port Control Register C (PCRC) .......................................................................... 131 9.7.2 Port Data Register C (PDRC) .............................................................................. 131 9.7.3 Pin Functions ....................................................................................................... 131 Section 10 Timer B1..........................................................................................133 10.1 Features ............................................................................................................................. 133 10.2 Register Descriptions ........................................................................................................ 134 10.2.1 Timer Mode Register B1 (TMB1) ....................................................................... 134 10.2.2 Timer Counter B1 (TCB1)................................................................................... 135 10.2.3 Timer Load Register B1 (TLB1) ......................................................................... 135 10.3 Operation .......................................................................................................................... 136 10.3.1 Interval Timer Operation ..................................................................................... 136 10.3.2 Auto-Reload Timer Operation ............................................................................. 136 10.4 Timer B1 Operating Modes .............................................................................................. 136 Section 11 Timer V............................................................................................137 11.1 Features ............................................................................................................................. 137 11.2 Input/Output Pins .............................................................................................................. 138 11.3 Register Descriptions ........................................................................................................ 139 11.3.1 Timer Counter V (TCNTV) ................................................................................. 139 11.3.2 Time Constant Registers A and B (TCORA, TCORB) ....................................... 139 Rev. 1.00, 11/03, page xii of xxviii 11.3.3 Timer Control Register V0 (TCRV0) ..................................................................140 11.3.4 Timer Control/Status Register V (TCSRV) .........................................................142 11.3.5 Timer Control Register V1 (TCRV1) ..................................................................143 11.4 Operation...........................................................................................................................144 11.4.1 Timer V Operation ...............................................................................................144 11.5 Timer V Application Examples.........................................................................................147 11.5.1 Pulse Output with Arbitrary Duty Cycle..............................................................147 11.5.2 Pulse Output with Arbitrary Pulse Width and Delay from TRGV Input .............148 11.6 Usage Notes ......................................................................................................................149 Section 12 Timer W .......................................................................................... 151 12.1 Features .............................................................................................................................151 12.2 Input/Output Pins ..............................................................................................................153 12.3 Register Descriptions ........................................................................................................154 12.3.1 Timer Mode Register W (TMRW) ......................................................................155 12.3.2 Timer Control Register W (TCRW) ....................................................................156 12.3.3 Timer Interrupt Enable Register W (TIERW)......................................................157 12.3.4 Timer Status Register W (TSRW) .......................................................................158 12.3.5 Timer I/O Control Register 0 (TIOR0) ................................................................160 12.3.6 Timer I/O Control Register 1 (TIOR1) ................................................................161 12.3.7 Timer Counter (TCNT)........................................................................................163 12.3.8 General Registers A to D (GRA to GRD)............................................................163 12.4 Operation...........................................................................................................................164 12.4.1 Normal Operation ................................................................................................164 12.4.2 PWM Operation ...................................................................................................168 12.5 Operation Timing ..............................................................................................................172 12.5.1 TCNT Count Timing............................................................................................172 12.5.2 Output Compare Output Timing ..........................................................................173 12.5.3 Input Capture Timing...........................................................................................174 12.5.4 Timing of Counter Clearing by Compare Match .................................................174 12.5.5 Buffer Operation Timing .....................................................................................175 12.5.6 Timing of IMFA to IMFD Flag Setting at Compare Match.................................176 12.5.7 Timing of IMFA to IMFD Setting at Input Capture ............................................177 12.5.8 Timing of Status Flag Clearing ............................................................................177 12.6 Usage Notes ......................................................................................................................178 Section 13 Watchdog Timer ............................................................................. 181 13.1 Features .............................................................................................................................181 13.2 Register Descriptions ........................................................................................................182 13.2.1 Timer Control/Status Register WD (TCSRWD)..................................................182 13.2.2 Timer Counter WD (TCWD) ...............................................................................184 13.2.3 Timer Mode Register WD (TMWD) ...................................................................184 13.3 Operation...........................................................................................................................185 Rev. 1.00, 11/03, page xiii of xxviii Section 14 Serial Communication Interface 3 (SCI3) .......................................187 14.1 Features ............................................................................................................................. 187 14.2 Input/Output Pins .............................................................................................................. 189 14.3 Register Descriptions ........................................................................................................ 189 14.3.1 Receive Shift Register (RSR) .............................................................................. 190 14.3.2 Receive Data Register (RDR) .............................................................................. 190 14.3.3 Transmit Shift Register (TSR) ............................................................................. 190 14.3.4 Transmit Data Register (TDR)............................................................................. 190 14.3.5 Serial Mode Register (SMR)................................................................................ 191 14.3.6 Serial Control Register 3 (SCR3)......................................................................... 192 14.3.7 Serial Status Register (SSR) ................................................................................ 194 14.3.8 Bit Rate Register (BRR) ...................................................................................... 196 14.3.9 Sampling Mode Register (SPMR) ....................................................................... 201 14.4 Operation in Asynchronous Mode .................................................................................... 202 14.4.1 Clock.................................................................................................................... 202 14.4.2 SCI3 Initialization................................................................................................ 203 14.4.3 Data Transmission ............................................................................................... 204 14.4.4 Serial Data Reception .......................................................................................... 206 14.5 Operation in Clocked Synchronous Mode ........................................................................ 208 14.5.1 Clock.................................................................................................................... 208 14.5.2 SCI3 Initialization................................................................................................ 208 14.5.3 Serial Data Transmission ..................................................................................... 209 14.5.4 Serial Data Reception (Clocked Synchronous Mode).......................................... 211 14.5.5 Simultaneous Serial Data Transmission and Reception....................................... 213 14.6 Multiprocessor Communication Function......................................................................... 215 14.6.1 Multiprocessor Serial Data Transmission ............................................................ 217 14.6.2 Multiprocessor Serial Data Reception ................................................................. 218 14.7 Interrupts ........................................................................................................................... 222 14.8 Usage Notes ...................................................................................................................... 223 14.8.1 Break Detection and Processing .......................................................................... 223 14.8.2 Mark State and Break Sending............................................................................. 223 14.8.3 Receive Error Flags and Transmit Operations (Clocked Synchronous Mode Only) .................................................................... 223 14.8.4 Receive Data Sampling Timing and Reception Margin in Asynchronous Mode.................................................................................................................... 224 Section 15 I2C Bus Interface 2 (IIC2) ...............................................................225 15.1 Features ............................................................................................................................. 225 15.2 Input/Output Pins .............................................................................................................. 227 15.3 Register Descriptions ........................................................................................................ 227 15.3.1 I2C Bus Control Register 1 (ICCR1).................................................................... 228 15.3.2 I2C Bus Control Register 2 (ICCR2).................................................................... 229 15.3.3 I2C Bus Mode Register (ICMR)........................................................................... 231 Rev. 1.00, 11/03, page xiv of xxviii 15.3.4 I2C Bus Interrupt Enable Register (ICIER)..........................................................232 15.3.5 I2C Bus Status Register (ICSR)............................................................................234 15.3.6 Slave Address Register (SAR) .............................................................................236 15.3.7 I2C Bus Transmit Data Register (ICDRT) ...........................................................237 15.3.8 I2C Bus Receive Data Register (ICDRR).............................................................237 15.3.9 I2C Bus Shift Register (ICDRS)...........................................................................237 15.4 Operation...........................................................................................................................238 15.4.1 I2C Bus Format ....................................................................................................238 15.4.2 Master Transmit Operation ..................................................................................239 15.4.3 Master Receive Operation....................................................................................241 15.4.4 Slave Transmit Operation ....................................................................................243 15.4.5 Slave Receive Operation ......................................................................................244 15.4.6 Clocked Synchronous Serial Format....................................................................246 15.4.7 Noise Canceler .....................................................................................................248 15.4.8 Example of Use....................................................................................................249 15.5 Interrupts ...........................................................................................................................253 15.6 Bit Synchronous Circuit.................................................................................................... 254 Section 16 A/D Converter................................................................................. 255 16.1 Features .............................................................................................................................255 16.2 Input/Output Pins ..............................................................................................................257 16.3 Register Description..........................................................................................................257 16.3.1 A/D Data Registers A to D (ADDRA to ADDRD)..............................................257 16.3.2 A/D Control/Status Register (ADCSR)................................................................258 16.3.3 A/D Control Register (ADCR).............................................................................259 16.4 Operation...........................................................................................................................261 16.4.1 Single Mode .........................................................................................................261 16.4.2 Scan Mode ...........................................................................................................261 16.4.3 Input Sampling and A/D Conversion Time..........................................................262 16.4.4 External Trigger Input Timing .............................................................................263 16.5 A/D Conversion Accuracy Definitions .............................................................................264 16.6 Usage Notes ......................................................................................................................266 16.6.1 Permissible Signal Source Impedance .................................................................266 16.6.2 Influences on Absolute Accuracy ........................................................................266 Section 17 Band-Gap Circuit, Power-On Reset, and Low-Voltage Detection Circuits............................................................................................ 267 17.1 Features .............................................................................................................................268 17.2 Register Descriptions ........................................................................................................269 17.2.1 Low-Voltage-Detection Control Register (LVDCR) ...........................................269 17.2.2 Low-Voltage-Detection Status Register (LVDSR) ..............................................271 17.3 Operations .........................................................................................................................272 17.3.1 Power-On Reset Circuit .......................................................................................272 Rev. 1.00, 11/03, page xv of xxviii 17.3.2 Low-Voltage Detection Circuit............................................................................ 273 Section 18 Power Supply Circuit.......................................................................279 18.1 When Using Internal Power Supply Step-Down Circuit................................................... 279 18.2 When Not Using Internal Power Supply Step-Down Circuit............................................ 280 Section 19 List of Registers...............................................................................281 19.1 Register Addresses (Address Order) ................................................................................. 282 19.2 Register Bits...................................................................................................................... 285 19.3 Register States in Each Operating Mode........................................................................... 288 Section 20 Electrical Characteristics .................................................................291 20.1 Absolute Maximum Ratings ............................................................................................. 291 20.2 Electrical Characteristics (F-ZTATTM Version)................................................................ 292 20.2.1 Power Supply Voltage and Operating Ranges ..................................................... 292 20.2.2 DC Characteristics ............................................................................................... 294 20.2.3 AC Characteristics ............................................................................................... 299 20.2.4 A/D Converter Characteristics ............................................................................. 302 20.2.5 Watchdog Timer Characteristics.......................................................................... 303 20.2.6 Power-Supply-Voltage Detection Circuit Characteristics.................................... 304 20.2.7 LVDI External Voltage Detection Circuit Characteristics................................... 304 20.2.8 Power-On Reset Characteristics........................................................................... 305 20.2.9 Flash Memory Characteristics ............................................................................. 306 20.3 Electrical Characteristics (Masked ROM Version)........................................................... 308 20.3.1 Power Supply Voltage and Operating Ranges ..................................................... 308 20.3.2 DC Characteristics ............................................................................................... 310 20.3.3 AC Characteristics ............................................................................................... 315 20.3.4 A/D Converter Characteristics ............................................................................. 318 20.3.5 Watchdog Timer Characteristics.......................................................................... 319 20.3.6 Power-Supply-Voltage Detection Circuit Characteristics.................................... 320 20.3.7 LVDI External Voltage Detection Circuit Characteristics................................... 320 20.3.8 Power-On Reset Characteristics........................................................................... 321 20.4 Operation Timing.............................................................................................................. 322 20.5 Output Load Condition ..................................................................................................... 324 Appendix A Instruction Set ...............................................................................325 A.1 A.2 A.3 A.4 Instruction List .................................................................................................................. 325 Operation Code Map......................................................................................................... 340 Number of Execution States.............................................................................................. 343 Combinations of Instructions and Addressing Modes ...................................................... 354 Rev. 1.00, 11/03, page xvi of xxviii Appendix B I/O Port Block Diagrams .............................................................. 355 B.1 B.2 I/O Port Block Diagrams...................................................................................................355 Port States in Each Operating State...................................................................................369 Appendix C Product Code Lineup.................................................................... 370 Appendix D Package Dimensions .................................................................... 371 Index ......................................................................................................... 373 Rev. 1.00, 11/03, page xvii of xxviii Rev. 1.00, 11/03, page xviii of xxviii Figures Section 1 Figure 1.1 Figure 1.2 Figure 1.3 Figure 1.4 Figure 1.5 Figure 1.6 Overview Internal Block Diagram of H8/36912 Group.................................................................3 Internal Block Diagram of H8/36902 Group.................................................................4 Pin Arrangement of H8/36912 Group (LQFP-32).........................................................5 Pin Arrangement of H8/36902 Group (LQFP-32).........................................................6 Pin Arrangement of H8/36912 Group (SOP-32) ...........................................................7 Pin Arrangement of H8/36902 Group (SOP-32) ...........................................................8 Section 2 CPU Figure 2.1 Memory Map (1) .........................................................................................................12 Figure 2.1 Memory Map (2) .........................................................................................................13 Figure 2.2 CPU Registers .............................................................................................................14 Figure 2.3 Usage of General Registers .........................................................................................15 Figure 2.4 Relationship between Stack Pointer and Stack Area ...................................................16 Figure 2.5 General Register Data Formats (1) ..............................................................................18 Figure 2.5 General Register Data Formats (2) ..............................................................................19 Figure 2.6 Memory Data Formats.................................................................................................20 Figure 2.7 Instruction Formats......................................................................................................30 Figure 2.8 Branch Address Specification in Memory Indirect Mode ...........................................33 Figure 2.9 On-Chip Memory Access Cycle..................................................................................36 Figure 2.10 On-Chip Peripheral Module Access Cycle (3-State Access).....................................37 Figure 2.11 CPU Operation States................................................................................................38 Figure 2.12 State Transitions ........................................................................................................38 Figure 2.13 Example of Timer Configuration with Two Registers Allocated to Same Address......................................................................................................................40 Section 3 Figure 3.1 Figure 3.2 Figure 3.3 Figure 3.4 Section 4 Figure 4.1 Figure 4.2 Figure 4.2 Section 5 Figure 5.1 Figure 5.2 Figure 5.3 Exception Handling Reset Sequence............................................................................................................54 Stack Status after Exception Handling ........................................................................55 Interrupt Sequence.......................................................................................................57 Port Mode Register Setting and Interrupt Request Flag Clearing Procedure ..............58 Address Break Block Diagram of Address Break................................................................................59 Address Break Interrupt Operation Example (1) .........................................................63 Address Break Interrupt Operation Example (2) .........................................................64 Clock Pulse Generators Block Diagram of Clock Pulse Generators..................................................................65 State Transition of System Clock ................................................................................71 Flowchart of Clock Switching with Backup Function Enabled...................................72 Rev. 1.00, 11/03, page xix of xxviii Figure 5.4 Flowchart of Clock Switching with Backup Function Disabled (1) (From Internal RC Clock to External Clock)............................................................... 73 Figure 5.5 Flowchart of Clock Switching with Backup Function Disabled (2) (From External Clock to Internal RC Clock)............................................................... 74 Figure 5.6 Timing Chart of Switching Internal RC Clock to External Clock............................... 75 Figure 5.7 Timing Chart to Switch External Clock to Internal RC Clock .................................... 76 Figure 5.8 External Oscillation Backup Timing ........................................................................... 77 Figure 5.9 Example of Trimming Flow for Internal RC Oscillator Frequency............................. 78 Figure 5.10 Timing Chart of Trimming of Internal RC Oscillator Frequency.............................. 79 Figure 5.11 Example of Connection to Crystal Resonator ........................................................... 80 Figure 5.12 Equivalent Circuit of Crystal Resonator.................................................................... 80 Figure 5.13 Example of Connection to Ceramic Resonator.......................................................... 81 Figure 5.14 Example of External Clock Input .............................................................................. 81 Figure 5.15 Example of Incorrect Board Design .......................................................................... 82 Section 6 Power-Down Modes Figure 6.1 Mode Transition Diagram ...........................................................................................89 Section 7 Figure 7.1 Figure 7.2 Figure 7.3 Figure 7.4 Section 9 Figure 9.1 Figure 9.2 Figure 9.3 Figure 9.4 Figure 9.5 Figure 9.6 Figure 9.7 ROM Flash Memory Block Configuration............................................................................ 95 Programming/Erasing Flowchart Example in User Program Mode .......................... 102 Program/Program-Verify Flowchart.......................................................................... 104 Erase/Erase-Verify Flowchart ................................................................................... 107 I/O Ports Port 1 Pin Configuration............................................................................................ 111 Port 2 Pin Configuration............................................................................................ 115 Port 5 Pin Configuration............................................................................................ 117 Port 7 Pin Configuration............................................................................................ 121 Port 8 Pin Configuration............................................................................................ 123 Port B Pin Configuration ........................................................................................... 127 Port C Pin Configuration ........................................................................................... 130 Section 10 Timer B1 Figure 10.1 Block Diagram of Timer B1.................................................................................... 133 Section 11 Figure 11.1 Figure 11.2 Figure 11.3 Figure 11.4 Figure 11.5 Figure 11.6 Figure 11.7 Figure 11.8 Figure 11.9 Timer V Block Diagram of Timer V...................................................................................... 138 Increment Timing with Internal Clock .................................................................... 144 Increment Timing with External Clock ................................................................... 145 OVF Set Timing ...................................................................................................... 145 CMFA and CMFB Set Timing ................................................................................ 145 TMOV Output Timing ............................................................................................ 146 Clear Timing by Compare Match............................................................................ 146 Clear Timing by TMRIV Input ............................................................................... 146 Pulse Output Example ............................................................................................. 147 Rev. 1.00, 11/03, page xx of xxviii Figure 11.10 Figure 11.11 Figure 11.12 Figure 11.13 Example of Pulse Output Synchronized to TRGV Input.......................................148 Contention between TCNTV Write and Clear ......................................................149 Contention between TCORA Write and Compare Match .....................................150 Internal Clock Switching and TCNTV Operation .................................................150 Section 12 Timer W Figure 12.1 Timer W Block Diagram .........................................................................................153 Figure 12.2 Free-Running Counter Operation ............................................................................164 Figure 12.3 Periodic Counter Operation .....................................................................................165 Figure 12.4 0 and 1 Output Example (TOA = 0, TOB = 1) ........................................................165 Figure 12.5 Toggle Output Example (TOA = 0, TOB = 1) ........................................................166 Figure 12.6 Toggle Output Example (TOA = 0, TOB = 1) ........................................................166 Figure 12.7 Input Capture Operating Example ...........................................................................167 Figure 12.8 Buffer Operation Example (Input Capture) .............................................................167 Figure 12.9 PWM Mode Example (1) ........................................................................................168 Figure 12.10 PWM Mode Example (2) ......................................................................................169 Figure 12.11 Buffer Operation Example (Output Compare) ......................................................169 Figure 12.12 PWM Mode Example (TOB, TOC, and TOD = 0: Initial Output Values are Set to 0) .................................................................................................................170 Figure 12.13 PWM Mode Example (TOB, TOC, and TOD = 1: Initial Output Values are Set to 1) .................................................................................................................171 Figure 12.14 Count Timing for Internal Clock Source ...............................................................172 Figure 12.15 Count Timing for External Clock Source ..............................................................172 Figure 12.16 Output Compare Output Timing............................................................................173 Figure 12.17 Input Capture Input Signal Timing........................................................................174 Figure 12.18 Timing of Counter Clearing by Compare Match...................................................174 Figure 12.19 Buffer Operation Timing (Compare Match)..........................................................175 Figure 12.20 Buffer Operation Timing (Input Capture) .............................................................175 Figure 12.21 Timing of IMFA to IMFD Flag Setting at Compare Match ..................................176 Figure 12.22 Timing of IMFA to IMFD Flag Setting at Input Capture ......................................177 Figure 12.23 Timing of Status Flag Clearing by CPU................................................................177 Figure 12.24 Contention between TCNT Write and Clear .........................................................179 Figure 12.25 Internal Clock Switching and TCNT Operation ....................................................179 Figure 12.26 When Compare Match and Bit Manipulation Instruction to TCRW Occur at the Same Timing................................................................................................180 Section 13 Watchdog Timer Figure 13.1 Block Diagram of Watchdog Timer ........................................................................181 Figure 13.2 Watchdog Timer Operation Example ......................................................................185 Section 14 Figure 14.1 Figure 14.2 Figure 14.3 Serial Communication Interface 3 (SCI3) Block Diagram of SCI3 ...........................................................................................188 Block Diagram of Noise Filter Circuit ....................................................................201 Data Format in Asynchronous Communication ......................................................202 Rev. 1.00, 11/03, page xxi of xxviii Figure 14.4 Relationship between Output Clock and Transfer Data Phase (Asynchronous Mode)(Example with 8-Bit Data, Parity, Two Stop Bits) .............. 202 Figure 14.5 Sample SCI3 Initialization Flowchart ..................................................................... 203 Figure 14.6 Example of SCI3 Transmission in Asynchronous Mode (8-Bit Data, Parity, One Stop Bit) ........................................................................... 204 Figure 14.7 Sample Serial Transmission Data Flowchart (Asynchronous Mode)...................... 205 Figure 14.8 Example of SCI3 Reception in Asynchronous Mode (8-Bit Data, Parity, One Stop Bit) ........................................................................... 206 Figure 14.9 Sample Serial Reception Data Flowchart (Asynchronous Mode) ........................... 207 Figure 14.10 Data Format in Clocked Synchronous Communication ........................................ 208 Figure 14.11 Example of SCI3 Transmission in Clocked Synchronous Mode........................... 209 Figure 14.12 Sample Serial Transmission Flowchart (Clocked Synchronous Mode) ................ 210 Figure 14.13 Example of SCI3 Reception in Clocked Synchronous Mode................................ 211 Figure 14.14 Sample Serial Reception Flowchart (Clocked Synchronous Mode)...................... 212 Figure 14.15 Sample Flowchart of Simultaneous Serial Transmit and Receive Operations (Clocked Synchronous Mode) ............................................................................... 214 Figure 14.16 Example of Inter-Processor Communication Using Multiprocessor Format (Transmission of Data H'AA to Receiving Station A) .......................................... 216 Figure 14.17 Sample Multiprocessor Serial Transmission Flowchart ........................................ 217 Figure 14.18 Sample Multiprocessor Serial Reception Flowchart (1)........................................ 219 Figure 14.18 Sample Multiprocessor Serial Reception Flowchart (2)........................................ 220 Figure 14.19 Example of SCI3 Reception Using Multiprocessor Format (Example with 8-Bit Data, Multiprocessor Bit, One Stop Bit).............................. 221 Figure 14.20 Receive Data Sampling Timing in Asynchronous Mode ...................................... 224 Section 15 I2C Bus Interface 2 (IIC2) Figure 15.1 Block Diagram of I2C Bus Interface 2..................................................................... 226 Figure 15.2 External Circuit Connections of I/O Pins ................................................................ 227 Figure 15.3 I2C Bus Formats ...................................................................................................... 238 Figure 15.4 I2C Bus Timing........................................................................................................ 238 Figure 15.5 Master Transmit Mode Operation Timing (1) ......................................................... 240 Figure 15.6 Master Transmit Mode Operation Timing (2) ......................................................... 240 Figure 15.7 Master Receive Mode Operation Timing (1)........................................................... 242 Figure 15.8 Master Receive Mode Operation Timing (2)........................................................... 242 Figure 15.9 Slave Transmit Mode Operation Timing (1) ........................................................... 243 Figure 15.10 Slave Transmit Mode Operation Timing (2) ......................................................... 244 Figure 15.11 Slave Receive Mode Operation Timing (1)........................................................... 245 Figure 15.12 Slave Receive Mode Operation Timing (2)........................................................... 245 Figure 15.13 Clocked Synchronous Serial Transfer Format....................................................... 246 Figure 15.14 Transmit Mode Operation Timing......................................................................... 247 Figure 15.15 Receive Mode Operation Timing .......................................................................... 248 Figure 15.16 Block Diagram of Noise Canceler......................................................................... 248 Figure 15.17 Sample Flowchart for Master Transmit Mode....................................................... 249 Rev. 1.00, 11/03, page xxii of xxviii Figure 15.18 Figure 15.19 Figure 15.20 Figure 15.21 Section 16 Figure 16.1 Figure 16.2 Figure 16.3 Figure 16.4 Figure 16.5 Figure 16.6 Section 17 Figure 17.1 Figure 17.2 Figure 17.3 Figure 17.4 Figure 17.5 Figure 17.6 Sample Flowchart for Master Receive Mode ........................................................250 Sample Flowchart for Slave Transmit Mode.........................................................251 Sample Flowchart for Slave Receive Mode ..........................................................252 Timing of Bit Synchronous Circuit .......................................................................254 A/D Converter Block Diagram of A/D Converter............................................................................256 A/D Conversion Timing ..........................................................................................262 External Trigger Input Timing.................................................................................263 A/D Conversion Accuracy Definitions (1) ..............................................................264 A/D Conversion Accuracy Definitions (2) ..............................................................265 Analog Input Circuit Example.................................................................................266 Band-Gap Circuit, Power-On Reset and Low-Voltage Detection Circuits Block Diagram around BGR ...................................................................................268 Block Diagram of Power-On Reset Circuit and Low-Voltage Detection Circuit....269 Operational Timing of Power-On Reset Circuit ......................................................272 Operating Timing of LVDR Circuit ........................................................................273 Operational Timing of LVDI Circuit.......................................................................275 Operational Timing of LVDI Circuit (When Compared Voltage is Input through ExtU and ExtD Pins)).........................276 Figure 17.7 Timing for Enabling/Disabling of Low-Voltage Detection Circuit.........................277 Section 18 Power Supply Circuit Figure 18.1 Power Supply Connection when Internal Step-Down Circuit is Used ....................279 Figure 18.2 Power Supply Connection when Internal Step-Down Circuit is Not Used .............280 Section 20 Electrical Characteristics Figure 20.1 System Clock Input Timing.....................................................................................322 Figure 20.2 RES Low Width Timing..........................................................................................322 Figure 20.3 Input Timing............................................................................................................322 Figure 20.4 I2C Bus Interface Input/Output Timing ...................................................................323 Figure 20.5 SCK3 Input Clock Timing.......................................................................................323 Figure 20.6 SCI3 Input/Output Timing in Clocked Synchronous Mode ....................................324 Figure 20.7 Output Load Circuit.................................................................................................324 Appendix B I/O Port Block Diagrams Figure B.1 Port 1 Block Diagram (P17) .....................................................................................355 Figure B.2 Port 1 Block Diagram (P14) .....................................................................................356 Figure B.3 Port 2 Block Diagram (P22) .....................................................................................357 Figure B.4 Port 2 Block Diagram (P21) .....................................................................................358 Figure B.5 Port 2 Block Diagram (P20) .....................................................................................359 Figure B.6 (1) Port 5 Block Diagram (P57, P56) (for H8/36912 Group) ...................................360 Figure B.6 (2) Port 5 Block Diagram (P57, P56) (for H8/36902 Group) ...................................360 Figure B.7 Port 5 Block Diagram (P55) .....................................................................................361 Figure B.8 Port 5 Block Diagram (P76) .....................................................................................362 Rev. 1.00, 11/03, page xxiii of xxviii Figure B.9 Port 7 Block Diagram (P75) ..................................................................................... 362 Figure B.10 Port 7 Block Diagram (P74) ................................................................................... 363 Figure B.11 Port 8 Block Diagram (P84 to P81) ........................................................................ 364 Figure B.12 Port 8 Block Diagram (P80) ................................................................................... 365 Figure B.13 Port B Block Diagram (PB3,PB2) .......................................................................... 366 Figure B.14 Port B Block Diagram (PB1, PB0) ......................................................................... 366 Figure B.15 Port C Block Diagram (PC1) .................................................................................. 367 Figure B.16 Port C Block Diagram (PC0) .................................................................................. 368 Appendix D Package Dimensions Figure D.1 FP-32D Package Dimensions ................................................................................... 371 Figure D.2 LQFP-32 Package Dimension .................................................................................. 371 Rev. 1.00, 11/03, page xxiv of xxviii Tables Section 1 Overview Table 1.1 Pin Functions ................................................................................................................9 Section 2 Table 2.1 Table 2.2 Table 2.3 Table 2.3 Table 2.4 Table 2.5 Table 2.6 Table 2.6 Table 2.7 Table 2.8 Table 2.9 Table 2.10 Table 2.11 Table 2.12 Table 2.12 CPU Operation Notation......................................................................................................21 Data Transfer Instructions...........................................................................................22 Arithmetic Operations Instructions (1) .......................................................................23 Arithmetic Operations Instructions (2) .......................................................................24 Logic Operations Instructions .....................................................................................24 Shift Instructions.........................................................................................................25 Bit Manipulation Instructions (1)................................................................................26 Bit Manipulation Instructions (2)................................................................................27 Branch Instructions .....................................................................................................28 System Control Instructions........................................................................................29 Block Data Transfer Instructions ................................................................................29 Addressing Modes ..................................................................................................31 Absolute Address Access Ranges ...........................................................................32 Effective Address Calculation (1) ...........................................................................34 Effective Address Calculation (2) ...........................................................................35 Section 3 Exception Handling Table 3.1 Exception Sources and Vector Address ......................................................................45 Table 3.2 Interrupt Wait States ...................................................................................................56 Section 4 Address Break Table 4.1 Access and Data Bus Used..........................................................................................61 Section 5 Clock Pulse Generators Table 5.1 Crystal Resonator Parameters .......................................................................................80 Section 6 Power-Down Modes Table 6.1 Operating Frequency and Wait Time..........................................................................85 Table 6.2 Transition Mode after SLEEP Instruction Execution and Interrupt Handling ............89 Table 6.3 Internal State in Each Operating Mode.......................................................................90 Section 7 ROM Table 7.1 Setting Programming Modes ......................................................................................99 Table 7.2 Boot Mode Operation ...............................................................................................101 Table 7.3 System Clock Frequencies for which Automatic Adjustment of LSI Bit Rate is Possible.....................................................................................................................102 Table 7.4 Reprogram Data Computation Table ........................................................................105 Table 7.5 Additional-Program Data Computation Table ..........................................................105 Table 7.6 Programming Time ...................................................................................................105 Rev. 1.00, 11/03, page xxv of xxviii Section 10 Timer B1 Table 10.1 Timer B1 Operating Modes .................................................................................. 136 Section 11 Timer V Table 11.1 Pin Configuration.................................................................................................. 138 Table 11.2 Clock Signals to Input to TCNTV and Counting Conditions ............................... 141 Section 12 Timer W Table 12.1 Timer W Functions ............................................................................................... 152 Table 12.2 Pin Configuration.................................................................................................. 153 Section 14 Serial Communication Interface 3 (SCI3) Table 14.1 Pin Configuration.................................................................................................. 189 Table 14.2 Examples of BRR Settings for Various Bit Rates (Asynchronous Mode) ............ 197 Table 14.3 Maximum Bit Rate for Each Frequency (Asynchronous Mode) .......................... 199 Table 14.4 Examples of BRR Settings for Various Bit Rates (Clocked Synchronous Mode) .............................................................................. 200 Table 14.5 SSR Status Flags and Receive Data Handling ...................................................... 207 Table 14.6 SCI3 Interrupt Requests........................................................................................ 222 Section 15 I2C Bus Interface 2 (IIC2) Table 15.1 Pin Configuration.................................................................................................. 227 Table 15.2 Transfer Rate......................................................................................................... 229 Table 15.3 Interrupt Requests ................................................................................................. 253 Table 15.4 Time for Monitoring SCL ..................................................................................... 254 Section 16 A/D Converter Table 16.1 Pin Configuration.................................................................................................. 257 Table 16.2 Analog Input Channels and Corresponding ADDR Registers .............................. 258 Table 16.3 A/D Conversion Time (Single Mode)................................................................... 263 Section 17 Band-Gap Circuit, Power-On Reset and Low-Voltage Detection Circuits Table 17.1 LVDCR Settings and Select Functions ................................................................. 271 Section 20 Electrical Characteristics Table 20.1 Absolute Maximum Ratings ................................................................................. 291 Table 20.2 DC Characteristics (1)........................................................................................... 294 Table 20.2 DC Characteristics (2)........................................................................................... 298 Table 20.3 AC Characteristics ................................................................................................ 299 Table 20.4 I2C Bus Interface Timing ...................................................................................... 300 Table 20.5 Serial Interface (SCI3) Timing ............................................................................. 301 Table 20.6 A/D Converter Characteristics .............................................................................. 302 Table 20.7 Watchdog Timer Characteristics........................................................................... 303 Table 20.8 Power-Supply-Voltage Detection Circuit Characteristics..................................... 304 Table 20.9 LVDI External Voltage Detection Circuit Characteristics.................................... 304 Rev. 1.00, 11/03, page xxvi of xxviii Table 20.10 Table 20.11 Table 20.12 Table 20.12 Table 20.13 Table 20.14 Table 20.15 Table 20.16 Table 20.17 Table 20.18 Table 20.19 Table 20.20 Appendix A Table A.1 Table A.2 Table A.2 Table A.2 Table A.3 Table A.4 Table A.5 Power-On Reset Circuit Characteristics................................................................305 Flash Memory Characteristics...............................................................................306 DC Characteristics (1)...........................................................................................310 DC Characteristics (2)...........................................................................................314 AC Characteristics ................................................................................................315 I2C Bus Interface Timing ......................................................................................316 Serial Interface (SCI3) Timing..............................................................................317 A/D Converter Characteristics ..............................................................................318 Watchdog Timer Characteristics...........................................................................319 Power-Supply-Voltage Detection Circuit Characteristics.....................................320 LVDI External Voltage Detection Circuit Characteristics....................................320 Power-On Reset Circuit Characteristics................................................................321 Instruction Set Instruction Set .......................................................................................................327 Operation Code Map (1) .......................................................................................340 Operation Code Map (2) .......................................................................................341 Operation Code Map (3) .......................................................................................342 Number of Cycles in Each Instruction ..................................................................344 Number of Cycles in Each Instruction ..................................................................345 Combinations of Instructions and Addressing Modes ..........................................354 Rev. 1.00, 11/03, page xxvii of xxviii Rev. 1.00, 11/03, page xxviii of xxviii Section 1 Overview 1.1 Features * High-speed H8/300H central processing unit with an internal 16-bit architecture Upward-compatible with H8/300 CPU on an object level Sixteen 16-bit general registers 62 basic instructions * Various peripheral functions Timer B1* (8-bit timer) Timer V (8-bit timer) Timer W (16-bit timer) Watchdog timer SCI3 (Asynchronous or clocked synchronous serial communication interface) 10-bit A/D converter I2C bus interface* (conforms to the Philips I2C bus interface functions) POR/LVD (Power-on reset and low-voltage detection circuits) Address break Internal RC oscillator Note: * Available for the H8/36912 Group only. * On-chip memory Product Classification Flash memory version (F-ZTAT version) TM Type HD64F36912G HD64F36902G ROM 8 kbytes 8 kbytes RAM 1,536 bytes 1,536 bytes Remarks H8/36912F H8/36902F Masked ROM version H8/36912 H8/36911 H8/36902 H8/36901 H8/36900 HD64336912G HD64336911G HD64336902G HD64336901G HD64336900G 8 kbytes 4 kbytes 8 kbytes 4 kbytes 2 kbytes 512 bytes 256 bytes 512 bytes 256 bytes 256 bytes Under planning Under planning Under planning Under planning Under planning Note: F-ZTAT TM is a trademark of Renesas Technology Corp. * General I/O ports Eighteen I/O pins, including five large-current ports (IOL = 20 mA, @VOL = 1.5 V) Four input only pins (also used for analog input) Rev. 1.00, 11/03, page 1 of 376 * Supports various power-down modes * Compact package Package LQFP-32 SOP-32 Code TBD FP-32D Body Size 7.0 x 7.0 mm 11.3 x 20.45 mm Pin Pitch 0.8 mm 1.27 mm Remarks Under development Rev. 1.00, 11/03, page 2 of 376 1.2 Internal Block Diagram (OSC1) (OSC2) TEST VCC VSS VCL System clock generator Internal RC oscillator E10T_0 E10T_1 E10T_2 CPU H8/300H Data bus (upper) Data bus (lower) P17/ /TRGV P14/ Port 1 Address bus ROM RAM P76/TMOV P75/TMCIV P74/TMRIV Timer W SCI3 Port 7 Port B P22/TXD P21/RXD P20/SCK3 Port 2 Timer V I2 C bus interface P84/FTIOD P83/FTIOC P82/FTIOB P81/FTIOA P80/FTCI Timer B1 Watchdog timer P55/ P57/SCL P56/SDA / Port 5 A/D converter POR & LVD Port C PC0/OSC1 PC1/OSC2/CLKOUT Figure 1.1 Internal Block Diagram of H8/36912 Group PB3/AN3/ExtU PB2/AN2/ExtD PB1/AN1 PB0/AN0 AVCC Rev. 1.00, 11/03, page 3 of 376 Port 8 VCL (OSC1) (OSC2) TEST VCC VSS System clock generator Internal RC oscillator E10T_0 E10T_1 E10T_2 CPU H8/300H Data bus (upper) Data bus (lower) Port 1 P17/ /TRGV P14/ Address bus ROM RAM P76/TMOV P75/TMCIV P74/TMRIV P22/TXD P21/RXD P20/SCK3 Port 2 Timer W SCI3 Port 7 Port B Timer V Watchdog timer P84/FTIOD P83/FTIOC P82/FTIOB P81/FTIOA P80/FTCI Port 5 P57 P56 P55/ / A/D converter POR & LVD Port C PC0/OSC1 PC1/OSC2/CLKOUT Figure 1.2 Internal Block Diagram of H8/36902 Group Rev. 1.00, 11/03, page 4 of 376 PB3/AN3/ExtU PB2/AN2/ExtD PB1/AN1 PB0/AN0 AVCC Port 8 1.3 Pin Arrangement P83/FTIOC P82/FTIOB P81/FTIOA P20/SCK3 18 P80/FTCI P21/RXD P22/TXD 24 23 22 21 20 19 P84/FTIOD P74/TMRIV P75/TMCIV P76/TMOV PB3/AN3/ExtU PB2/AN2/ExtD PB1/AN1 PB0/AN0 25 26 27 28 29 30 31 32 H8/36912 Group (Top view) 17 16 15 14 13 12 11 10 9 P55/ / P14/ P56/SDA P57/SCL ET10_2 E10T_1 E10T_0 P17/ /TRGV 1 2 3 4 5 6 7 PC0/OSC1 PC1/OSC2/CLKOUT TEST AVcc Figure 1.3 Pin Arrangement of H8/36912 Group (LQFP-32) Vcc Vss VCL 8 Rev. 1.00, 11/03, page 5 of 376 P83/FTIOC P82/FTIOB P81/FTIOA P20/SCK3 18 P80/FTCI P21/RXD P22/TXD 24 23 22 21 20 19 P84/FTIOD P74/TMRIV P75/TMCIV P76/TMOV PB3/AN3/ExtU PB2/AN2/ExtD PB1/AN1 PB0/AN0 25 26 27 28 29 30 31 32 1 2 3 4 5 6 7 8 17 P55/ / 16 15 14 H8/36902 Group (Top view) 13 12 11 10 9 P14/ P56 P57 ET10_2 E10T_1 E10T_0 P17/ /TRGV PC1/OSC2/CLKOUT PC0/OSC1 TEST AVcc Figure 1.4 Pin Arrangement of H8/36902 Group (LQFP-32) Rev. 1.00, 11/03, page 6 of 376 Vcc Vss VCL PB3/AN3/ExtU PB2/AN2/ExtD PB1/AN1 PB0/AN0 AVcc Vcc 1 2 3 4 5 6 7 32 31 30 29 28 27 26 H8/36912 Group (Top view) 25 24 23 22 21 20 19 18 17 P76/TMOV P75/TMCIV P74/TMRIV P84/FTIOD P83/FTIOC P82/FTIOB P81/FTIOA P80/FTCI P22/TXD P21/RXD P20/SCK3 P55/ P14/ P56/SDA P57/SCL ET10_2 / TEST Vss PC1/OSC2/CLKOUT PC0/OSC1 VCL 8 9 10 11 12 13 P17/ /TRGV E10T_0 E10T_1 14 15 16 Figure 1.5 Pin Arrangement of H8/36912 Group (SOP-32) Rev. 1.00, 11/03, page 7 of 376 PB3/AN3/ExtU PB2/AN2/ExtD PB1/AN1 PB0/AN0 AVcc Vcc 1 2 3 4 5 6 7 32 31 30 29 28 27 26 H8/36902 Group (Top view) 25 24 23 22 21 20 19 18 17 P76/TMOV P75/TMCIV P74/TMRIV P84/FTIOD P83/FTIOC P82/FTIOB P81/FTIOA P80/FTCI P22/TXD P21/RXD P20/SCK3 P55/ P14/ P56 P57 ET10_2 / TEST Vss PC1/OSC2/CLKOUT PC0/OSC1 VCL 8 9 10 11 12 13 P17/ /TRGV E10T_0 E10T_1 14 15 16 Figure 1.6 Pin Arrangement of H8/36902 Group (SOP-32) Rev. 1.00, 11/03, page 8 of 376 1.4 Table 1.1 Pin Functions Pin Functions Pin No. Type Power source Symbol VCC VSS AVCC SOP-32 6 9 5 LQFP-32 I/O 2 5 1 Input Input Input Functions Power supply pin. Connect this pin to the system power supply. Ground pin. Connect this pin to the system power supply (0 V). Analog power supply pin for the A/D converter. When the A/D converter is not used, connect this pin to the system power supply. Internal step-down power supply pin. Connect a capacitor of around 0.1 F between this pin and the Vss pin for stabilization. These pins are connected to a crystal or ceramic resonator for system clocks, or can be used to input an external clock. When an internal RC oscillator is used, system clocks can be output to OSC2. See section 5, Clock Pulse Generators, for a typical connection. Reset pin. The pull-up resistor (typ. 150 k) is incorporated. When driven low, the chip is reset. Test pin. Connect this pin to Vss. Non-maskable interrupt request input pin External interrupt request input pins. Can select the rising or falling edge. External interrupt request input pin. Can select the rising or falling edge. VCL 12 8 Input Clock OSC1 OSC2/ CLKOUT 11 10 7 6 Input Output System control RES 7 3 Input TEST External interrupt NMI IRQ0, IRQ3 WKP5 8 13 20, 14 4 9 16, 10 Input Input Input 21 17 Input Rev. 1.00, 11/03, page 9 of 376 Pin No. Type Timer V Symbol TMOV SOP-32 32 LQFP-32 28 I/O Output Functions TMOV is an output pin for waveforms generated by the output compare function. External event input pin Counter reset input pin Counter start trigger input pin External event input pin Output compare output/ input capture input/ PWM output common pins I C data I/O pin. NMOS open drain output can directly drive the bus. I C clock I/O pin. NMOS open drain output can directly drive the bus. Transmit data output pin Receive data input pin Clock I/O pin Analog input pin A/D converter trigger input pin 2-bit I/O port 3-bit I/O port 3-bit I/O port 3-bit I/O port 5-bit I/O port 4-bit input port 2-bit I/O port External input pins for the detection voltage used in the low-voltage detection circuit Interface pins for E7 emulator 2 2 TMCIV TMRIV TRGV Timer W FTCI FTIOA to FTIOD I C bus interface 2 31 30 14 25 26 to 29 27 26 10 21 22 to 25 Input Input Input Input I/O SDA SCL 19 18 24 23 22 15 14 20 19 18 29 to 32 17 10, 16 20 to 18 28 to 26 25 to 21 29 to 32 6, 7 29, 30 I/O I/O Output Input I/O Input Input I/O I/O I/O I/O Input I/O Input Serial communication interface A/D converter I/O ports TXD RXD SCK3 ADTRG P17, P14 P22 to P20 P57 to P55 P76 to P74 P84 to P80 PC1, PC0 AN3 to AN0 1 to 4 21 14, 20 24 to 22 18, 19, 21 32 to 30 29 to 25 10, 11 1, 2 14, 15, 17 I/O PB3 to PB0 1 to 4 Low voltage ExtU, ExtD detection circuit E7 E10T_0, E10T_1, E10T_2 15, 16, 17 11, 12, 13 Note: Available for the H8/36912 Group only. Rev. 1.00, 11/03, page 10 of 376 Section 2 CPU This LSI has an H8/300H CPU with an internal 32-bit architecture that is upward-compatible with the H8/300 CPU, and supports only normal mode, which has a 64-kbyte address space. * Upward-compatible with H8/300 CPUs Can execute H8/300 CPUs object programs Additional eight 16-bit extended registers 32-bit transfer and arithmetic and logic instructions are added Signed multiply and divide instructions are added. * General-register architecture Sixteen 16-bit general registers also usable as sixteen 8-bit registers or eight 32-bit registers * Sixty-two basic instructions 8/16/32-bit data transfer and arithmetic and logic instructions Multiply and divide instructions Powerful bit-manipulation instructions * Eight addressing modes Register direct [Rn] Register indirect [@ERn] Register indirect with displacement [@(d:16,ERn) or @(d:24,ERn)] Register indirect with post-increment or pre-decrement [@ERn+ or @-ERn] Absolute address [@aa:8, @aa:16, @aa:24] Immediate [#xx:8, #xx:16, or #xx:32] Program-counter relative [@(d:8,PC) or @(d:16,PC)] Memory indirect [@@aa:8] * 64-kbyte address space * High-speed operation All frequently-used instructions execute in one or two states 8/16/32-bit register-register add/subtract 8 x 8-bit register-register multiply 16 / 8-bit register-register divide 32 / 16-bit register-register divide * Power-down state Transition to power-down state by SLEEP instruction : 2 state : 14 states : 14 states : 22 states 16 x 16-bit register-register multiply : 22 states CPU30H2E_000120030300 Rev. 1.00, 11/03, page 11 of 376 2.1 Address Space and Memory Map The address space of this LSI is 64 kbytes, which includes the program area and the data area. The following two figures show the memory map, respectively. H8/36912 H8/36902 (Masked ROM version (under planning)) H'0000 H'0045 H'0046 Interrupt vector H8/36912F H8/36902F (Flash memory version) H'0000 H'0045 H'0046 Interrupt vector On-chip ROM (8 kbytes) On-chip ROM (8 kbytes) H'1FFF H'2000 E7 control program area (4 kbytes) H'1FFF H'2FFF Not used Not used H'F600 H'F77F H'F980 Internal I/O register Not used (E7 work area, for flash memory programming: 1 kbyte) On-chip RAM (1.5 kbytes) On-chip RAM user area (512 bytes) H'F600 H'F77F Internal I/O register Not used H'FD7F H'FD80 H'FD80 On-chip RAM user area (512 bytes) H'FF7F H'FF80 H'FF7F H'FF80 Internal I/O register H'FFFF Internal I/O register H'FFFF Figure 2.1 Memory Map (1) Rev. 1.00, 11/03, page 12 of 376 H8/36911 H8/36901 (Masked ROM version (under planning)) H'0000 H'0045 H'0046 Interrupt vector H'0000 H'0045 H'0046 H8/36900 (Masked ROM version (under planning)) Interrupt vector On-chip ROM (2 kbytes) On-chip ROM (4 kbytes) H'07FF H'0FFF Not used Not used H'F600 H'F77F Internal I/O register H'F600 H'F77F Internal I/O register Not used Not used H'FE80 On-chip RAM user area (256 bytes) H'FF7F H'FF80 Internal I/O register H'FFFF H'FE80 On-chip RAM user area (256 bytes) H'FF7F H'FF80 Internal I/O register H'FFFF Figure 2.1 Memory Map (2) Rev. 1.00, 11/03, page 13 of 376 2.2 Register Configuration The H8/300H CPU has the internal registers shown in figure 2.2. There are two types of registers; general registers and control registers. The control registers are a 24-bit program counter (PC), and an 8-bit condition code register (CCR). General registers (ERn) 15 ER0 ER1 ER2 ER3 ER4 ER5 ER6 ER7 (SP) E0 E1 E2 E3 E4 E5 E6 E7 07 R0H R1H R2H R3H R4H R5H R6H R7H 07 R0L R1L R2L R3L R4L R5L R6L R7L 0 Control registers (CR) 23 PC 0 76543210 CCR I UI H U N Z V C [Legend] Stack pointer SP: Program counter PC: CCR: Condition-code register Interrupt mask bit I: User bit UI: H: U: N: Z: V: C: Half-carry flag User bit Negative flag Zero flag Overflow flag Carry flag Figure 2.2 CPU Registers Rev. 1.00, 11/03, page 14 of 376 2.2.1 General Registers The H8/300H CPU has eight 32-bit general registers. These general registers are all functionally identical and can be used as both address registers and data registers. When a general register is used as a data register, it can be accessed as a 32-bit, 16-bit, or 8-bit register. Figure 2.3 illustrates the usage of the general registers. When the general registers are used as 32-bit registers or address registers, they are designated by the letters ER (ER0 to ER7). The ER registers divide into 16-bit general registers designated by the letters E (E0 to E7) and R (R0 to R7). These registers are functionally equivalent, providing a maximum of sixteen 16-bit registers. The E registers (E0 to E7) are also referred to as extended registers. The R registers divide into 8-bit registers designated by the letters RH (R0H to R7H) and RL (R0L to R7L). These registers are functionally equivalent, providing a maximum of sixteen 8-bit registers. The usage of each register can be selected independently. * Address registers * 32-bit registers * 16-bit registers * 8-bit registers E registers (extended registers) (E0 to E7) ER registers (ER0 to ER7) R registers (R0 to R7) RL registers (R0L to R7L) RH registers (R0H to R7H) Figure 2.3 Usage of General Registers General register ER7 has the function of stack pointer (SP) in addition to its general-register function, and is used implicitly in exception handling and subroutine calls. Figure 2.4 shows the stack. Rev. 1.00, 11/03, page 15 of 376 Free area SP (ER7) Stack area Figure 2.4 Relationship between Stack Pointer and Stack Area 2.2.2 Program Counter (PC) This 24-bit counter indicates the address of the next instruction the CPU will execute. The length of all CPU instructions is 2 bytes (one word), so the least significant PC bit is ignored. (When an instruction is fetched, the least significant PC bit is regarded as 0). The PC is initialized when the start address is loaded by the vector address generated during reset exception-handling sequence. 2.2.3 Condition-Code Register (CCR) This 8-bit register contains internal CPU status information, including an interrupt mask bit (I) and half-carry (H), negative (N), zero (Z), overflow (V), and carry (C) flags. The I bit is initialized to 1 by reset exception-handling sequence, but other bits are not initialized. Some instructions leave flag bits unchanged. Operations can be performed on the CCR bits by the LDC, STC, ANDC, ORC, and XORC instructions. The N, Z, V, and C flags are used as branching conditions for conditional branch (Bcc) instructions. For the action of each instruction on the flag bits, see Appendix A.1, Instruction List. Rev. 1.00, 11/03, page 16 of 376 Bit 7 Bit Name I Initial Value 1 R/W R/W Description Interrupt Mask Bit Masks interrupts other than NMI when set to 1. NMI is accepted regardless of the I bit setting. The I bit is set to 1 at the start of an exception-handling sequence. 6 UI Undefined R/W User Bit Can be written and read by software using the LDC, STC, ANDC, ORC, and XORC instructions. 5 H Undefined R/W Half-Carry Flag When the ADD.B, ADDX.B, SUB.B, SUBX.B, CMP.B, or NEG.B instruction is executed, this flag is set to 1 if there is a carry or borrow at bit 3, and cleared to 0 otherwise. When the ADD.W, SUB.W, CMP.W, or NEG.W instruction is executed, the H flag is set to 1 if there is a carry or borrow at bit 11, and cleared to 0 otherwise. When the ADD.L, SUB.L, CMP.L, or NEG.L instruction is executed, the H flag is set to 1 if there is a carry or borrow at bit 27, and cleared to 0 otherwise. 4 U Undefined R/W User Bit Can be written and read by software using the LDC, STC, ANDC, ORC, and XORC instructions. 3 N Undefined R/W Negative Flag Stores the value of the most significant bit of data as a sign bit. 2 Z Undefined R/W Zero Flag Set to 1 to indicate zero data, and cleared to 0 to indicate non-zero data. 1 V Undefined R/W Overflow Flag Set to 1 when an arithmetic overflow occurs, and cleared to 0 at other times. 0 C Undefined R/W Carry Flag Set to 1 when a carry occurs, and cleared to 0 otherwise. Used by: * * * Add instructions, to indicate a carry Subtract instructions, to indicate a borrow Shift and rotate instructions, to indicate a carry The carry flag is also used as a bit accumulator by bit manipulation instructions. Rev. 1.00, 11/03, page 17 of 376 2.3 Data Formats The H8/300H CPU can process 1-bit, 4-bit (BCD), 8-bit (byte), 16-bit (word), and 32-bit (longword) data. Bit-manipulation instructions operate on 1-bit data by accessing bit n (n = 0, 1, 2, ..., 7) of byte operand data. The DAA and DAS decimal-adjust instructions treat byte data as two digits of 4-bit BCD data. 2.3.1 General Register Data Formats Figure 2.5 shows the data formats in general registers. Data Type 1-bit data General Register RnH Data Format 7 0 Don't care 7 0 76 54 32 10 1-bit data RnL Don't care 76 54 32 10 7 4-bit BCD data RnH Upper 43 Lower 0 Don't care 7 4-bit BCD data RnL Don't care Upper 43 Lower 0 7 Byte data RnH MSB 0 Don't care LSB 7 0 LSB Byte data RnL Don't care MSB Figure 2.5 General Register Data Formats (1) Rev. 1.00, 11/03, page 18 of 376 Data Type Word data General Register Rn Data Format 15 0 Word data En 15 0 MSB LSB MSB LSB 16 15 0 Longword data ERn 31 MSB LSB [Legend] ERn: En: Rn: RnH: RnL: LSB: General register ER General register E General register R General register RH General register RL Least significant bit MSB: Most significant bit Figure 2.5 General Register Data Formats (2) Rev. 1.00, 11/03, page 19 of 376 2.3.2 Memory Data Formats Figure 2.6 shows the data formats in memory. The H8/300H CPU can access word data and longword data in memory, however word or longword data must begin at an even address. If an attempt is made to access word or longword data at an odd address, an address error does not occur, however the least significant bit of the address is regarded as 0, so access begins the preceding address. This also applies to instruction fetches. When ER7 (SP) is used as an address register to access the stack, the operand size should be word or longword. Data Type Address 7 1-bit data Address L 7 6 5 4 3 2 1 Data Format 0 0 Byte data Address L MSB LSB Word data Address 2M Address 2M+1 MSB LSB Longword data Address 2N Address 2N+1 Address 2N+2 Address 2N+3 MSB LSB Figure 2.6 Memory Data Formats Rev. 1.00, 11/03, page 20 of 376 2.4 2.4.1 Instruction Set Table of Instructions Classified by Function The H8/300H CPU has 62 instructions. Tables 2.2 to 2.9 summarize the instructions in each functional category. The notation used in tables 2.2 to 2.9 is defined below. Table 2.1 Symbol Rd Rs Rn ERn (EAd) (EAs) CCR N Z V C PC SP #IMM disp + - x / :3/:8/:16/:24 Note: * Operation Notation Description General register (destination)* General register (source)* General register* General register (32-bit register or address register) Destination operand Source operand Condition-code register N (negative) flag in CCR Z (zero) flag in CCR V (overflow) flag in CCR C (carry) flag in CCR Program counter Stack pointer Immediate data Displacement Addition Subtraction Multiplication Division Logical AND Logical OR Logical XOR Move NOT (logical complement) 3-, 8-, 16-, or 24-bit length General registers include 8-bit registers (R0H to R7H, R0L to R7L), 16-bit registers (R0 to R7, E0 to E7), and 32-bit registers/address registers (ER0 to ER7). Rev. 1.00, 11/03, page 21 of 376 Table 2.2 Instruction MOV Data Transfer Instructions Size* B/W/L Function (EAs) Rd, Rs (EAd) Moves data between two general registers or between a general register and memory, or moves immediate data to a general register. (EAs) Rd, Cannot be used in this LSI. Rs (EAs) Cannot be used in this LSI. @SP+ Rn Pops a general register from the stack. POP.W Rn is identical to MOV.W @SP+, Rn. POP.L ERn is identical to MOV.L @SP+, ERn. Rn @-SP Pushes a general register onto the stack. PUSH.W Rn is identical to MOV.W Rn, @-SP. PUSH.L ERn is identical to MOV.L ERn, @-SP. MOVFPE MOVTPE POP B B W/L PUSH W/L Note: * Refers to the operand size. B: Byte W: Word L: Longword Rev. 1.00, 11/03, page 22 of 376 Table 2.3 Instruction ADD SUB Arithmetic Operations Instructions (1) Size* B/W/L Function Rd Rs Rd, Rd #IMM Rd Performs addition or subtraction on data in two general registers, or on immediate data and data in a general register (immediate byte data cannot be subtracted from byte data in a general register. Use the SUBX or ADD instruction.) Rd Rs C Rd, Rd #IMM C Rd Performs addition or subtraction with carry on byte data in two general registers, or on immediate data and data in a general register. Rd 1 Rd, Rd 2 Rd Increments or decrements a general register by 1 or 2. (Byte operands can be incremented or decremented by 1 only.) Rd 1 Rd, Rd 2 Rd, Rd 4 Rd Adds or subtracts the value 1, 2, or 4 to or from data in a 32-bit register. Rd decimal adjust Rd Decimal-adjusts an addition or subtraction result in a general register by referring to the CCR to produce 4-bit BCD data. Rd x Rs Rd Performs unsigned multiplication on data in two general registers: either 8 bits x 8 bits 16 bits or 16 bits x 16 bits 32 bits. Rd x Rs Rd Performs signed multiplication on data in two general registers: either 8 bits x 8 bits 16 bits or 16 bits x 16 bits 32 bits. Rd / Rs Rd Performs unsigned division on data in two general registers: either 16 bits / 8 bits 8-bit quotient and 8-bit remainder or 32 bits / 16 bits 16-bit quotient and 16-bit remainder. ADDX SUBX INC DEC ADDS SUBS DAA DAS MULXU B B/W/L L B B/W MULXS B/W DIVXU B/W Note: * Refers to the operand size. B: Byte W: Word L: Longword Rev. 1.00, 11/03, page 23 of 376 Table 2.3 Instruction DIVXS Arithmetic Operations Instructions (2) Size* B/W Function Rd / Rs Rd Performs signed division on data in two general registers: either 16 bits / 8 bits 8-bit quotient and 8-bit remainder or 32 bits / 16 bits 16-bit quotient and 16-bit remainder. Rd - Rs, Rd - #IMM Compares data in a general register with data in another general register or with immediate data, and sets CCR bits according to the result. 0 - Rd Rd Takes the two's complement (arithmetic complement) of data in a general register. Rd (zero extension) Rd Extends the lower 8 bits of a 16-bit register to word size, or the lower 16 bits of a 32-bit register to longword size, by padding with zeros on the left. Rd (sign extension) Rd Extends the lower 8 bits of a 16-bit register to word size, or the lower 16 bits of a 32-bit register to longword size, by extending the sign bit. CMP B/W/L NEG B/W/L EXTU W/L EXTS W/L Note: * Refers to the operand size. B: Byte W: Word L: Longword Table 2.4 Instruction AND Logic Operations Instructions Size* B/W/L Function Rd Rs Rd, Rd #IMM Rd Performs a logical AND operation on a general register and another general register or immediate data. Rd Rs Rd, Rd #IMM Rd Performs a logical OR operation on a general register and another general register or immediate data. Rd Rs Rd, Rd #IMM Rd Performs a logical exclusive OR operation on a general register and another general register or immediate data. (Rd) (Rd) Takes the one's complement of general register contents. OR B/W/L XOR B/W/L NOT Note: * B/W/L Refers to the operand size. B: Byte W: Word L: Longword Rev. 1.00, 11/03, page 24 of 376 Table 2.5 Instruction SHAL SHAR SHLL SHLR ROTL ROTR ROTXL ROTXR Note: * Shift Instructions Size* B/W/L B/W/L B/W/L B/W/L Function Rd (shift) Rd Performs an arithmetic shift on general register contents. Rd (shift) Rd Performs a logical shift on general register contents. Rd (rotate) Rd Rotates general register contents. Rd (rotate) Rd Rotates general register contents through the carry flag. Refers to the operand size. B: Byte W: Word L: Longword Rev. 1.00, 11/03, page 25 of 376 Table 2.6 Instruction BSET Bit Manipulation Instructions (1) Size* B Function 1 ( BCLR B BNOT B BTST B BAND B BIAND B BOR B BIOR B Note: * Refers to the operand size. B: Byte Rev. 1.00, 11/03, page 26 of 376 Table 2.6 Instruction BXOR Bit Manipulation Instructions (2) Size* B Function C ( BIXOR B BLD B BILD B BST B BIST B Note: * Refers to the operand size. B: Byte Rev. 1.00, 11/03, page 27 of 376 Table 2.7 Instruction Bcc* Branch Instructions Size -- Function Branches to a specified address if a specified condition is true. The branching conditions are listed below. Mnemonic BRA(BT) BRN(BF) BHI BLS BCC(BHS) BCS(BLO) BNE BEQ BVC BVS BPL BMI BGE BLT BGT BLE Description Always (true) Never (false) High Low or same Carry clear (high or same) Carry set (low) Not equal Equal Overflow clear Overflow set Plus Minus Greater or equal Less than Greater than Less or equal Condition Always Never CZ=0 CZ=1 C=0 C=1 Z=0 Z=1 V=0 V=1 N=0 N=1 NV=0 NV=1 Z(N V) = 0 Z(N V) = 1 JMP BSR JSR RTS Note: * -- -- -- -- Branches unconditionally to a specified address. Branches to a subroutine at a specified address. Branches to a subroutine at a specified address. Returns from a subroutine Bcc is the general name for conditional branch instructions. Rev. 1.00, 11/03, page 28 of 376 Table 2.8 Instruction TRAPA RTE SLEEP LDC System Control Instructions Size* -- -- -- B/W Function Starts trap-instruction exception handling. Returns from an exception-handling routine. Causes a transition to a power-down state. (EAs) CCR Moves the source operand contents to the CCR. The CCR size is one byte, but in transfer from memory, data is read by word access. CCR (EAd), EXR (EAd) Transfers the CCR contents to a destination location. The condition code register size is one byte, but in transfer to memory, data is written by word access. CCR #IMM CCR, EXR #IMM EXR Logically ANDs the CCR with immediate data. CCR #IMM CCR, EXR #IMM EXR Logically ORs the CCR with immediate data. CCR #IMM CCR, EXR #IMM EXR Logically XORs the CCR with immediate data. PC + 2 PC Only increments the program counter. STC B/W ANDC ORC XORC NOP Note: * B B B -- Refers to the operand size. B: Byte W: Word Table 2.9 Instruction EEPMOV.B Block Data Transfer Instructions Size -- Function if R4L 0 then Repeat @ER5+ @ER6+, R4L-1 R4L Until R4L = 0 else next; if R4 0 then Repeat @ER5+ @ER6+, R4-1 R4 Until R4 = 0 else next; Transfers a data block. Starting from the address set in ER5, transfers data for the number of bytes set in R4L or R4 to the address location set in ER6. Execution of the next instruction begins as soon as the transfer is completed. Rev. 1.00, 11/03, page 29 of 376 EEPMOV.W -- 2.4.2 Basic Instruction Formats H8/300H CPU instructions consist of 2-byte (1-word) units. An instruction consists of an operation field (op field), a register field (r field), an effective address extension (EA field), and a condition field (cc). Figure 2.7 shows examples of instruction formats. Operation Field: Indicates the function of the instruction, the addressing mode, and the operation to be carried out on the operand. The operation field always includes the first four bits of the instruction. Some instructions have two operation fields. Register Field: Specifies a general register. Address registers are specified by 3 bits, and data registers by 3 bits or 4 bits. Some instructions have two register fields. Some have no register field. Effective Address Extension: 8, 16, or 32 bits specifying immediate data, an absolute address, or a displacement. A24-bit address or displacement is treated as a 32-bit data in which the first 8 bits are 0 (H'00). Condition Field: Specifies the branching condition of Bcc instructions. (1) Operation field only op NOP, RTS, etc. (2) Operation field and register fields op rn rm ADD.B Rn, Rm, etc. (3) Operation field, register fields, and effective address extension op EA(disp) rn rm MOV.B @(d:16, Rn), Rm (4) Operation field, effective address extension, and condition field op cc EA(disp) BRA d:8 Figure 2.7 Instruction Formats Rev. 1.00, 11/03, page 30 of 376 2.5 Addressing Modes and Effective Address Calculation The following describes the H8/300H CPU. In this LSI, the upper eight bits are ignored in the generated 24-bit address, so the effective address is 16 bits. 2.5.1 Addressing Modes The H8/300H CPU supports the eight addressing modes listed in table 2.10. Each instruction uses a subset of these addressing modes. Addressing modes that can be used differ depending on the instruction. For details, refer to Appendix A.4, Combinations of Instructions and Addressing Modes. Arithmetic and logic instructions can use the register direct and immediate modes. Data transfer instructions can use all addressing modes except program-counter relative and memory indirect. Bit manipulation instructions use register direct, register indirect, or the absolute addressing mode to specify an operand, and register direct (BSET, BCLR, BNOT, and BTST instructions) or immediate (3-bit) addressing mode to specify a bit number in the operand. Table 2.10 Addressing Modes No. 1 2 3 4 5 6 7 8 Addressing Mode Register direct Register indirect Register indirect with displacement Register indirect with post-increment Register indirect with pre-decrement Absolute address Immediate Program-counter relative Memory indirect Symbol Rn @ERn @(d:16,ERn)/@(d:24,ERn) @ERn+ @-ERn @aa:8/@aa:16/@aa:24 #xx:8/#xx:16/#xx:32 @(d:8,PC)/@(d:16,PC) @@aa:8 Register Direct--Rn The register field of the instruction specifies an 8-, 16-, or 32-bit general register containing the operand. R0H to R7H and R0L to R7L can be specified as 8-bit registers. R0 to R7 and E0 to E7 can be specified as 16-bit registers. ER0 to ER7 can be specified as 32-bit registers. Register Indirect--@ERn The register field of the instruction code specifies an address register (ERn), the lower 24 bits of which contain the address of the operand on memory. Rev. 1.00, 11/03, page 31 of 376 Register Indirect with Displacement--@(d:16, ERn) or @(d:24, ERn) A 16-bit or 24-bit displacement contained in the instruction is added to an address register (ERn) specified by the register field of the instruction, and the lower 24 bits of the sum the address of a memory operand. A 16-bit displacement is sign-extended when added. Register Indirect with Post-Increment or Pre-Decrement--@ERn+ or @-ERn * Register indirect with post-increment--@ERn+ The register field of the instruction code specifies an address register (ERn) the lower 24 bits of which contains the address of a memory operand. After the operand is accessed, 1, 2, or 4 is added to the address register contents (32 bits) and the sum is stored in the address register. The value added is 1 for byte access, 2 for word access, or 4 for longword access. For the word or longword access, the register value should be even. * Register indirect with pre-decrement--@-ERn The value 1, 2, or 4 is subtracted from an address register (ERn) specified by the register field in the instruction code, and the lower 24 bits of the result is the address of a memory operand. The result is also stored in the address register. The value subtracted is 1 for byte access, 2 for word access, or 4 for longword access. For the word or longword access, the register value should be even. Absolute Address--@aa:8, @aa:16, @aa:24 The instruction code contains the absolute address of a memory operand. The absolute address may be 8 bits long (@aa:8), 16 bits long (@aa:16), 24 bits long (@aa:24) For an 8-bit absolute address, the upper 16 bits are all assumed to be 1 (H'FFFF). For a 16-bit absolute address the upper 8 bits are a sign extension. A 24-bit absolute address can access the entire address space. The access ranges of absolute addresses for the group of this LSI are those shown in table 2.11, because the upper 8 bits are ignored. Table 2.11 Absolute Address Access Ranges Absolute Address 8 bits (@aa:8) 16 bits (@aa:16) 24 bits (@aa:24) Access Range H'FF00 to H'FFFF H'0000 to H'FFFF H'0000 to H'FFFF Rev. 1.00, 11/03, page 32 of 376 Immediate--#xx:8, #xx:16, or #xx:32 The instruction contains 8-bit (#xx:8), 16-bit (#xx:16), or 32-bit (#xx:32) immediate data as an operand. The ADDS, SUBS, INC, and DEC instructions contain immediate data implicitly. Some bit manipulation instructions contain 3-bit immediate data in the instruction code, specifying a bit number. The TRAPA instruction contains 2-bit immediate data in its instruction code, specifying a vector address. Program-Counter Relative--@(d:8, PC) or @(d:16, PC) This mode is used in the BSR instruction. An 8-bit or 16-bit displacement contained in the instruction is sign-extended and added to the 24-bit PC contents to generate a branch address. The PC value to which the displacement is added is the address of the first byte of the next instruction, so the possible branching range is -126 to +128 bytes (-63 to +64 words) or -32766 to +32768 bytes (-16383 to +16384 words) from the branch instruction. The resulting value should be an even number. Memory Indirect--@@aa:8 This mode can be used by the JMP and JSR instructions. The instruction code contains an 8-bit absolute address specifying a memory operand. This memory operand contains a branch address. The memory operand is accessed by longword access. The first byte of the memory operand is ignored, generating a 24-bit branch address. Figure 2.8 shows how to specify branch address for in memory indirect mode. The upper bits of the absolute address are all assumed to be 0, so the address range is 0 to 255 (H'0000 to H'00FF). Note that the first part of the address range is also the exception vector area. Specified by @aa:8 Dummy Branch address Figure 2.8 Branch Address Specification in Memory Indirect Mode Rev. 1.00, 11/03, page 33 of 376 2.5.2 Effective Address Calculation Table 2.12 indicates how effective addresses are calculated in each addressing mode. In this LSI, the upper 8 bits of the effective address are ignored in order to generate a 16-bit effective address. Table 2.12 Effective Address Calculation (1) No 1 Addressing Mode and Instruction Format Register direct(Rn) Effective Address Calculation Effective Address (EA) Operand is general register contents. op 2 rm rn 31 General register contents Register indirect(@ERn) 0 23 0 op 3 r Register indirect with displacement @(d:16,ERn) or @(d:24,ERn) 31 General register contents 0 23 0 op r disp 31 Sign extension 0 disp 4 Register indirect with post-increment or pre-decrement *Register indirect with post-increment @ERn+ 31 General register contents 0 23 0 op r 31 1, 2, or 4 *Register indirect with pre-decrement @-ERn 0 General register contents 23 0 op r 1, 2, or 4 The value to be added or subtracted is 1 when the operand is byte size, 2 for word size, and 4 for longword size. Rev. 1.00, 11/03, page 34 of 376 Table 2.12 Effective Address Calculation (2) No 5 Addressing Mode and Instruction Format Absolute address Effective Address Calculation Effective Address (EA) @aa:8 op abs 23 H'FFFF 87 0 @aa:16 op abs 23 16 15 0 Sign extension @aa:24 op abs 23 0 6 Immediate #xx:8/#xx:16/#xx:32 op IMM Operand is immediate data. 7 Program-counter relative @(d:8,PC) @(d:16,PC) 23 PC contents 0 op disp 23 Sign extension 0 disp 23 0 8 Memory indirect @@aa:8 23 op abs H'0000 15 87 abs 0 0 Memory contents 23 16 15 H'00 0 [Legend] r, rm,rn : op : disp : IMM : abs : Register field Operation field Displacement Immediate data Absolute address Rev. 1.00, 11/03, page 35 of 376 2.6 Basic Bus Cycle CPU operation is synchronized by a system clock (). The period from a rising edge of to the next rising edge is called one state. A bus cycle consists of two states or three states. The cycle differs depending on whether access is to on-chip memory or to on-chip peripheral modules. 2.6.1 Access to On-Chip Memory (RAM, ROM) Access to on-chip memory takes place in two states. The data bus width is 16 bits, allowing access in byte or word size. Figure 2.9 shows the on-chip memory access cycle. Bus cycle T1 state T2 state Internal address bus Address Internal read signal Internal data bus (read access) Read data Internal write signal Internal data bus (write access) Write data Figure 2.9 On-Chip Memory Access Cycle Rev. 1.00, 11/03, page 36 of 376 2.6.2 On-Chip Peripheral Modules On-chip peripheral modules are accessed in two states or three states. The data bus width is 8 bits or 16 bits depending on the register. For description on the data bus width and number of accessing states of each register, refer to section 19.1, Register Addresses (Address Order). Registers with 16-bit data bus width can be accessed by word size only. Registers with 8-bit data bus width can be accessed by byte or word size. When a register with 8-bit data bus width is accessed by word size, a bus cycle occurs twice. In two-state access, the operation timing is the same as that for on-chip memory. Figure 2.10 shows the operation timing in the case of three-state access to an on-chip peripheral module. Bus cycle T1 state T2 state T3 state Internal address bus Internal read signal Internal data bus (read access) Internal write signal Internal data bus (write access) Address Read data Write data Figure 2.10 On-Chip Peripheral Module Access Cycle (3-State Access) Rev. 1.00, 11/03, page 37 of 376 2.7 CPU States There are four CPU states: the reset state, program execution state, program halt state, and exception-handling state. The program execution state includes active mode. In the program halt state there are a sleep mode, and standby mode. These states are shown in figure 2.11. Figure 2.12 shows the state transitions. For details on program execution state and program halt state, refer to section 6, Power-Down Modes. For details on exception processing, refer to section 3, Exception Handling. CPU state Reset state The CPU is initialized Program execution state Active (high speed) mode The CPU executes successive program instructions at high speed, synchronized by the system clock Program halt state A state in which some or all of the chip functions are stopped to conserve power Sleep mode Power-down modes Standby mode Exceptionhandling state A transient state in which the CPU changes the processing flow due to a reset or an interrupt Figure 2.11 CPU Operation States Reset cleared Reset state Reset occurs Exception-handling state Reset occurs Reset occurs Interrupt source Interrupt source Exceptionhandling complete Program halt state SLEEP instruction executed Program execution state Figure 2.12 State Transitions Rev. 1.00, 11/03, page 38 of 376 2.8 2.8.1 Usage Notes Notes on Data Access to Empty Areas The address space of this LSI includes empty areas in addition to the ROM, RAM, and on-chip I/O registers areas available to the user. When data is transferred from CPU to empty areas, the transferred data will be lost. This action may also cause the CPU to malfunction. When data is transferred from an empty area to CPU, the contents of the data cannot be guaranteed. 2.8.2 EEPMOV Instruction EEPMOV is a block-transfer instruction and transfers the byte size of data indicated by R4L, which starts from the address indicated by R5, to the address indicated by R6. Set R4L and R6 so that the end address of the destination address (value of R6 + R4L) does not exceed H'FFFF (the value of R6 must not change from H'FFFF to H'0000 during execution). 2.8.3 Bit Manipulation Instruction The BSET, BCLR, BNOT, BST, and BIST instructions read data from the specified address in byte units, manipulate the data of the target bit, and write data to the same address again in byte units. Special care is required when using these instructions in cases where two registers are assigned to the same address or when a bit is directly manipulated for a port, because this may rewrite data of a bit other than the bit to be manipulated. Rev. 1.00, 11/03, page 39 of 376 Bit Manipulation for Two Registers Assigned to the Same Address Example 1: Bit manipulation for the timer load register and timer counter (Applicable to timer B1, not available for the H8/36902 Group.) Figure 2.13 shows an example of a timer in which two timer registers are assigned to the same address. When a bit manipulation instruction accesses the timer load register and timer counter of a reloadable timer, since these two registers share the same address, the following operations takes place. 1. Data is read in byte units. 2. The CPU sets or resets the bit to be manipulated with the bit manipulation instruction. 3. The written data is written again in byte units to the timer load register. The timer is counting, so the value read is not necessarily the same as the value in the timer load register. As a result, bits other than the intended bit in the timer counter may be modified and the modified value may be written to the timer load register. Read Count clock Timer counter Reload Write Timer load register Internal bus Figure 2.13 Example of Timer Configuration with Two Registers Allocated to Same Address Example 2: The BSET instruction is executed for port 5. P57 and P56 are input pins, with a low-level signal input at P57 and a high-level signal input at P56. P55 to P50 are output pins and output low-level signals. An example to output a high-level signal at P50 with a BSET instruction is shown below. Rev. 1.00, 11/03, page 40 of 376 [Prior to executing BSET] P57 Input/output Pin state PCR5 PDR5 Input Low level 0 1 P56 Input High level 0 0 P55 Output Low level 1 0 P54 Output Low level 1 0 P53 Output Low level 1 0 P52 Output Low level 1 0 P51 Output Low level 1 0 P50 Output Low level 1 0 [BSET instruction executed] BSET #0, @PDR5 The BSET instruction is executed for port 5. [After executing BSET] P57 Input/output Pin state PCR5 PDR5 Input Low level 0 0 P56 Input High level 0 1 P55 Output Low level 1 0 P54 Output Low level 1 0 P53 Output Low level 1 0 P52 Output Low level 1 0 P51 Output Low level 1 0 P50 Output High level 1 1 [Description on operation] 1. When the BSET instruction is executed, first the CPU reads port 5. Since P57 and P56 are input pins, the CPU reads the pin states (low-level and high-level input). P55 to P50 are output pins, so the CPU reads the value in PDR5. In this example PDR5 has a value of H'80, but the value read by the CPU is H'40. 2. Next, the CPU sets bit 0 of the read data to 1, changing the PDR5 data to H'41. 3. Finally, the CPU writes H'41 to PDR5, completing execution of BSET. As a result of the BSET instruction, bit 0 in PDR5 becomes 1, and P50 outputs a high-level signal. However, bits 7 and 6 of PDR5 end up with different values. To prevent this problem, store a copy of the PDR5 data in a work area in memory. Perform the bit manipulation on the data in the work area, then write this data to PDR5. Rev. 1.00, 11/03, page 41 of 376 [Prior to executing BSET] MOV.B MOV.B MOV.B #80, R0L, R0L, P57 Input/output Pin state PCR5 PDR5 RAM0 Input Low level 0 1 1 R0L @RAM0 @PDR5 P56 Input High level 0 0 0 The PDR5 value (H'80) is written to a work area in memory (RAM0) as well as to PDR5. P55 Output Low level 1 0 0 P54 Output Low level 1 0 0 P53 Output Low level 1 0 0 P52 Output Low level 1 0 0 P51 Output Low level 1 0 0 P50 Output Low level 1 0 0 [BSET instruction executed] BSET #0, @RAM0 The BSET instruction is executed designating the PDR5 work area (RAM0). [After executing BSET] MOV.B MOV.B @RAM0, R0L R0L, @PDR5 P57 Input/output Pin state PCR5 PDR5 RAM0 Input Low level 0 1 1 P56 Input High level 0 0 0 The work area (RAM0) value is written to PDR5. P55 Output Low level 1 0 0 P54 Output Low level 1 0 0 P53 Output Low level 1 0 0 P52 Output Low level 1 0 0 P51 Output Low level 1 0 0 P50 Output High level 1 1 1 Bit Manipulation in a Register Containing a Write-Only Bit Example 3: BCLR instruction executed designating port 5 control register PCR5 P57 and P56 are input pins, with a low-level signal input at P57 and a high-level signal input at P56. P55 to P50 are output pins that output low-level signals. An example of setting the P50 pin as an input pin by the BCLR instruction is shown below. It is assumed that a high-level signal will be input to this input pin. Rev. 1.00, 11/03, page 42 of 376 [Prior to executing BCLR] P57 Input/output Pin state PCR5 PDR5 Input Low level 0 1 P56 Input High level 0 0 P55 Output Low level 1 0 P54 Output Low level 1 0 P53 Output Low level 1 0 P52 Output Low level 1 0 P51 Output Low level 1 0 P50 Output Low level 1 0 [BCLR instruction executed] BCLR #0, @PCR5 The BCLR instruction is executed for PCR5. [After executing BCLR] P57 Input/output Pin state PCR5 PDR5 Output Low level 1 1 P56 Output High level 1 0 P55 Output Low level 1 0 P54 Output Low level 1 0 P53 Output Low level 1 0 P52 Output Low level 1 0 P51 Output Low level 1 0 P50 Input High level 0 0 [Description on operation] 1. When the BCLR instruction is executed, first the CPU reads PCR5. Since PCR5 is a write-only register, the CPU reads a value of H'FF, even though the PCR5 value is actually H'3F. 2. Next, the CPU clears bit 0 in the read data to 0, changing the data to H'FE. 3. Finally, H'FE is written to PCR5 and BCLR instruction execution ends. As a result of this operation, bit 0 in PCR5 becomes 0, making P50 an input port. However, bits 7 and 6 in PCR5 change to 1, so that P57 and P56 change from input pins to output pins. To prevent this problem, store a copy of the PCR5 data in a work area in memory and manipulate data of the bit in the work area, then write this data to PCR5. Rev. 1.00, 11/03, page 43 of 376 [Prior to executing BCLR] MOV.B MOV.B MOV.B #3F, R0L, R0L, P57 Input/output Pin state PCR5 PDR5 RAM0 Input Low level 0 1 0 R0L @RAM0 @PCR5 P56 Input High level 0 0 0 The PCR5 value (H'3F) is written to a work area in memory (RAM0) as well as to PCR5. P55 Output Low level 1 0 1 P54 Output Low level 1 0 1 P53 Output Low level 1 0 1 P52 Output Low level 1 0 1 P51 Output Low level 1 0 1 P50 Output Low level 1 0 1 [BCLR instruction executed] BCLR #0, @RAM0 The BCLR instructions executed for the PCR5 work area (RAM0). [After executing BCLR] MOV.B MOV.B @RAM0, R0L R0L, @PCR5 P57 Input/output Pin state PCR5 PDR5 RAM0 Input Low level 0 1 0 P56 Input High level 0 0 0 The work area (RAM0) value is written to PCR5. P55 Output Low level 1 0 1 P54 Output Low level 1 0 1 P53 Output Low level 1 0 1 P52 Output Low level 1 0 1 P51 Output Low level 1 0 1 P50 Output High level 0 0 0 Rev. 1.00, 11/03, page 44 of 376 Section 3 Exception Handling Exception handling may be caused by a reset, a trap instruction (TRAPA), or interrupts. * Reset A reset has the highest exception priority. Exception handling starts as soon as the reset is cleared by the RES pin. The chip is also reset when the watchdog timer overflows, and exception handling starts. Exception handling is the same as exception handling by the RES pin. * Trap Instruction Exception handling starts when a trap instruction (TRAPA) is executed. The TRAPA instruction generates a vector address corresponding to a vector number from 0 to 3, as specified in the instruction code. Exception handling can be executed at all times in the program execution state. * Interrupts External interrupts other than NMI and internal interrupts other than address break are masked by the I bit in CCR, and kept masked while the I bit is set to 1. Exception handling starts when the current instruction or exception handling ends, if an interrupt request has been issued. 3.1 Exception Sources and Vector Address Table 3.1 shows the vector addresses and priority of each exception handling. When more than one interrupt is requested, handling is performed from the interrupt with the highest priority. Table 3.1 Exception Sources and Vector Address Exception Sources Reset Reserved for system use NMI Trap instruction #0 Trap instruction #1 Trap instruction #2 Trap instruction #3 Address break CPU Break conditions satisfied Direct transition by executing the SLEEP instruction Vector Number 0 1 to 6 7 8 9 10 11 12 13 Vector Address H'0000 to H'0001 H'0002 to H'000D H'000E to H'000F H'0010 to H'0011 H'0012 to H'0013 H'0014 to H'0015 H'0016 to H'0017 H'0018 to H'0019 H'001A to H'001B Low Priority High Relative Module RES pin Watchdog timer External interrupt pin CPU Rev. 1.00, 11/03, page 45 of 376 Relative Module External interrupt pin External interrupt pin Timer W Exception Sources IRQ0, low-voltage detection interrupt Reserved for system use IRQ3 WKP Reserved for system use Timer W input capture A/ compare match A Timer W input capture B/ compare match B Timer W input capture C/ compare match C Timer W input capture D/ compare match D Timer W overflow Timer V compare match A Timer V compare match B Timer V overflow SCI3 receive data full SCI3 transmit data empty SCI3 transmit end SCI3 receive error IIC_2 transmit data empty IIC_2 transmit end IIC_2 receive error A/D conversion end Reserved for system use Timer B1 overflow Reserved for system use Vector Number 14 15, 16 17 18 19, 20 21 Vector Address H'001C to H'001D H'001E to H'0021 H'0022 to H'0023 H'0024 to H'0025 H'0026 to H'0029 H'002A to H'002B Priority High Timer V 22 H'002C to H'002D SCI3 23 H'002E to H'002F IIC_2 24 H'0030 to H'0031 A/D converter Timer B1 Clock switch 25 26 to 28 29 30 to 33 H'0032 to H'0033 H'0034 to H'0039 H'003A to H'003B H'003C to H'0043 H'0044 to H'0045 Low Clock switch (external clock to 34 internal clock) Rev. 1.00, 11/03, page 46 of 376 3.2 Register Descriptions Interrupts are controlled by the following registers. * Interrupt edge select register 1 (IEGR1) * Interrupt edge select register 2 (IEGR2) * Interrupt enable register 1 (IENR1) * Interrupt enable register 2 (IENR2) * Interrupt flag register 1 (IRR1) * Interrupt flag register 2 (IRR2) * Wakeup interrupt flag register (IWPR) 3.2.1 Interrupt Edge Select Register 1 (IEGR1) IEGR1 selects the direction of an edge that generates interrupt requests of the IRQ3 and IRQ0 pins. Bit 7 6 to 4 3 Bit Name IEG3 Initial Value 0 All 1 0 R/W - R/W Description Reserved This bit is always read as 0. Reserved These bits are always read as 1. IRQ3 Edge Select 0: Falling edge of IRQ3 pin input is detected 1: Rising edge of IRQ3 pin input is detected 2, 1 0 IEG0 All 0 0 R/W Reserved These bits are always read as 0. IRQ0 Edge Select 0: Falling edge of IRQ0 pin input is detected 1: Rising edge of IRQ0 pin input is detected Rev. 1.00, 11/03, page 47 of 376 3.2.2 Interrupt Edge Select Register 2 (IEGR2) IEGR2 selects the direction of an edge that generates interrupt requests of the ADTRG and WKP5 pins. Bit 7, 6 5 Bit Name WPEG5 Initial Value All 1 0 R/W R/W Description Reserved These bits are always read as 1. WKP5 Edge Select 0: Falling edge of WKP5 (ADTRG) pin input is detected 1: Rising edge of WKP5 (ADTRG) pin input is detected 4 to 0 All 0 Reserved These bits are always read as 0. 3.2.3 Interrupt Enable Register 1 (IENR1) IENR1 enables direct transition interrupts and external pin interrupts. Bit 7 Bit Name IENDT Initial Value 0 R/W R/W Description Direct Transfer Interrupt Enable When this bit is set to 1, direct transition interrupt requests are enabled. 6 5 IENWP 0 0 R/W Reserved This bit is always read as 0. Wakeup Interrupt Enable This bit is an enable bit of the WKP5 pin. When this bit is set to 1, interrupt requests are enabled. 4 3 IEN3 1 0 R/W Reserved This bit is always read as 1. IRQ3 Interrupt Enable When this bit is set to 1, interrupt requests of the IRQ3 pin are enabled. 2, 1 0 IEN0 All 0 0 R/W Reserved These bits are always read as 0. IRQ0 Interrupt Enable When this bit is set to 1, interrupt requests of the IRQ0 pin are enabled. Rev. 1.00, 11/03, page 48 of 376 3.2.4 Interrupt Enable Register 2 (IENR2) IENR2 enables timer B1 interrupts. Bit 7 6 Bit Name Initial Value 0 0 R/W R/W Description Reserved This bit is always read as 0. Reserved Although this bit is readable/writable, it should not be set to 1. 5 IENTB1 0 R/W Timer B1 Interrupt Enable When this bit is set to 1, overflow interrupt requests of timer B1 are enabled. 4 to 0 All 1 Reserved These bits are always read as 1. When disabling interrupts by clearing bits in an interrupt enable register, or when clearing bits in an interrupt flag register, always do so while interrupts are masked (I = 1). If the above clear operations are performed while I = 0, and as a result a conflict arises between the clear instruction and an interrupt request, exception handling for the interrupt will be executed after the clear instruction has been executed. Rev. 1.00, 11/03, page 49 of 376 3.2.5 Interrupt Flag Register 1 (IRR1) IRR1 is a status flag register for direct transition interrupts, and IRQ3 and IRQ0 interrupt requests. Bit 7 Bit Name IRRDT Initial Value 0 R/W R/W Description Direct Transfer Interrupt Request Flag [Setting condition] When a direct transfer is made by executing a SLEEP instruction while DTON in SYSCR2 is set to 1. [Clearing condition] When IRRDT is cleared by writing 0 6 5, 4 3 IRRI3 0 All 1 0 R/W Reserved This bit is always read as 0. Reserved These bits are always read as 1. IRQ3 Interrupt Request Flag [Setting condition] When IRQ3 pin is designated for interrupt input and the designated signal edge is detected [Clearing condition] When IRRI3 is cleared by writing 0 2, 1 0 IRRl0 All 0 0 R/W Reserved These bits are always read as 0. IRQ0 Interrupt Request Flag [Setting condition] When IRQ0 pin is designated for interrupt input and the designated signal edge is detected [Clearing condition] When IRRI0 is cleared by writing 0 Rev. 1.00, 11/03, page 50 of 376 3.2.6 Interrupt Flag Register 2 (IRR2) IRR2 is a status flag register for timer B1 interrupt requests. Bit 7 6 5 Bit Name IRRTB1 Initial Value 0 0 R/W R/W Description Reserved This bit is always read as 0. Reserved Timer B1 Interrupt Request Flag [Setting condition] When timer B1 overflows [Clearing condition] When IRRTB1 is cleared by writing 0 4 to 0 All 1 Reserved These bits are always read as 1. 3.2.7 Wakeup Interrupt Flag Register (IWPR) IWPR is a status flag register for WKP5 interrupt requests. Bit 7, 6 5 Bit Name IWPF5 Initial Value All 1 0 R/W R/W Description Reserved These bits are always read as 1. WKP5 Interrupt Request Flag [Setting condition] When WKP5 pin is designated for interrupt input and the designated signal edge is detected. [Clearing condition] When IWPF5 is cleared by writing 0 4 to 0 All 0 Reserved These bits are always read as 0. Rev. 1.00, 11/03, page 51 of 376 3.3 Reset Exception Handling When the RES pin goes low, all processing halts and this LSI enters the reset. The internal state of the CPU and the registers of the on-chip peripheral modules are initialized by the reset. To ensure that this LSI is reset at power-up, hold the RES pin low for the specified period. To reset the chip during operation, hold the RES pin low for the specified period. For details, refer to section 17, Band-Gap Circuit, Power-On Reset, and Low-Voltage Detection Circuits. When the RES pin goes high after being held low for a certain period, this LSI starts reset exception handling. The reset exception handling sequence is shown in figure 3.1. The reset exception handling sequence is as follows. 1. Set the I bit in the condition code register (CCR) to 1. 2. The CPU generates a reset exception handling vector address (from H'0000 to H'0001), the data in that address is sent to the program counter (PC) as the start address, and program execution starts from that address. Rev. 1.00, 11/03, page 52 of 376 3.4 3.4.1 Interrupt Exception Handling External Interrupts As external interrupts, there are NMI, IRQ3, IRQ0, and WKP5 interrupts. NMI Interrupt: NMI interrupt is requested by input falling edge to the NMI pin. NMI is the highest interrupt, and can always be accepted without depending on the I bit value in CCR. IRQ3 and IRQ0 Interrupts: IRQ3 and IRQ0 interrupts are requested by input signals to the IRQ3 and IRQ0 pins. These interrupts are given different vector addresses, and are detected individually by either rising edge sensing or falling edge sensing, depending on the settings of the IEG3 and IEG0 bits in IEGR1. When the IRQ3 and IRQ0 pins are designated for interrupt input in PMR1 and the designated signal edge is input, the corresponding bit in IRR1 is set to 1, requesting the CPU of an interrupt. These interrupts can be masked by setting the IEN3 and IEN0 bits in IENR1. WKP Interrupt: WKP interrupt is requested by an input signal to the WKP5 pin. This interrupt is detected by either rising edge sensing or falling edge sensing, depending on the setting of the WPEG5 bit in IEGR2. When the WKP5 pin is designated for interrupt input in PMR5 and the designated signal edge is input, the corresponding bit in IWPR is set to 1, requesting the CPU of an interrupt. This interrupt can be masked by setting the IENWP bit in IENR1. Rev. 1.00, 11/03, page 53 of 376 Reset cleared Initial program instruction prefetch Vector fetch Internal processing Internal address bus Internal read signal Internal write signal Internal data bus (16 bits) ~ ~ ~ (1) (2) ~ ~ ~ (2) (3) (1) Reset exception handling vector address (H'0000) (2) Program start address (3) Initial program instruction Figure 3.1 Reset Sequence 3.4.2 Internal Interrupts Each on-chip peripheral module has a flag to show the interrupt request status and the enable bit to enable or disable the interrupt. For direct transfer interrupt requests generated by execution of a SLEEP instruction, this function is included in IRR1 and IENR1. When an on-chip peripheral module requests an interrupt, the corresponding interrupt request status flag is set to 1, requesting the CPU of an interrupt. When this interrupt is accepted, the I bit is set to 1 in CCR. These interrupts can be masked by writing 0 to clear the corresponding enable bit. 3.4.3 Interrupt Handling Sequence Interrupts are controlled by an interrupt controller. Interrupt operation is described as follows. 1. If an interrupt occurs while the NMI or interrupt enable bit is set to 1, an interrupt request signal is sent to the interrupt controller. Rev. 1.00, 11/03, page 54 of 376 2. When multiple interrupt requests are generated, the interrupt controller requests to the CPU for the interrupt handling with the highest priority at that time according to table 3.1. Other interrupt requests are held pending. 3. The CPU accepts the NMI or address break without depending on the I bit value. Other interrupt requests are accepted, if the I bit is cleared to 0 in CCR; if the I bit is set to 1, the interrupt request is held pending. 4. If the CPU accepts the interrupt after processing of the current instruction is completed, interrupt exception handling will begin. First, both PC and CCR are pushed onto the stack. The state of the stack at this time is shown in figure 3.2. The PC value pushed onto the stack is the address of the first instruction to be executed upon return from interrupt handling. 5. Then, the I bit of CCR is set to 1, masking further interrupts excluding the NMI and address break. Upon return from interrupt handling, the values of I bit and other bits in CCR will be restored and returned to the values prior to the start of interrupt exception handling. 6. Next, the CPU generates the vector address corresponding to the accepted interrupt, and transfers the address to PC as a start address of the interrupt handling-routine. Then a program starts executing from the address indicated in PC. Figure 3.3 shows a typical interrupt sequence where the program area is in the on-chip ROM and the stack area is in the on-chip RAM. SP - 4 SP - 3 SP - 2 SP - 1 SP (R7) Stack area SP (R7) SP + 1 SP + 2 SP + 3 SP + 4 CCR CCR* PCH PCL Even address Prior to start of interrupt exception handling PC and CCR saved to stack After completion of interrupt exception handling [Legend] PCH : Upper 8 bits of program counter (PC) PCL : Lower 8 bits of program counter (PC) CCR: Condition code register SP: Stack pointer Notes: PC shows the address of the first instruction to be executed upon return from the interrupt handling routine. Register contents must always be saved and restored by word length, starting from an even-numbered address. * Ignored when returning from the interrupt handling routine. Figure 3.2 Stack Status after Exception Handling Rev. 1.00, 11/03, page 55 of 376 3.4.4 Interrupt Response Time Table 3.2 shows the number of wait states after an interrupt request flag is set until the first instruction of the interrupt handling-routine is executed. Table 3.2 Item Waiting time for completion of executing instruction* Saving of PC and CCR to stack Vector fetch Instruction fetch Internal processing Note: * EEPMOV instruction is not included. Interrupt Wait States States 1 to 23 4 2 4 4 Total 15 to 37 Rev. 1.00, 11/03, page 56 of 376 Interrupt is accepted Interrupt level decision and wait for end of instruction Instruction prefetch Internal processing Stack access Vector fetch Prefetch instruction of Internal interrupt-handling routine processing Interrupt request signal Internal address bus (1) (3) (5) (6) (8) (9) Internal read signal Internal write signal (2) (4) (1) (7) (9) (10) Figure 3.3 Interrupt Sequence Internal data bus (16 bits) Rev. 1.00, 11/03, page 57 of 376 (1) Instruction prefetch address (Instruction is not executed. Address is saved as PC contents, becoming return address.) (2)(4) Instruction code (not executed) (3) Instruction prefetch address (Instruction is not executed.) (5) SP - 2 (6) SP - 4 (7) CCR (8) Vector address (9) Starting address of interrupt-handling routine (contents of vector) (10) First instruction of interrupt-handling routine 3.5 3.5.1 Usage Notes Interrupts after Reset If an interrupt is accepted after a reset and before the stack pointer (SP) is initialized, the PC and CCR will not be saved correctly, leading to a program crash. To prevent this, all interrupt requests, including NMI, are disabled immediately after a reset. Since the first instruction of a program is always executed immediately after the reset state ends, make sure that this instruction initializes the stack pointer (example: MOV.W #xx: 16, SP). 3.5.2 Notes on Stack Area Use When word data is accessed, the least significant bit of the address is regarded as 0. Access to the stack always takes place in word size, so the stack pointer (SP: R7) should never indicate an odd address. Use PUSH Rn (MOV.W Rn, @-SP) or POP Rn (MOV.W @SP+, Rn) to save or restore register values. 3.5.3 Notes on Rewriting Port Mode Registers When a port mode register is rewritten to switch the functions of external interrupt pins, IRQ3, IRQ0, and WKP5, the interrupt request flag may be set to 1. When switching a pin function, mask the interrupt before setting the bit in the port mode register. After accessing the port mode register, execute at least one instruction (e.g., NOP), then clear the interrupt request flag from 1 to 0. Figure 3.4 shows a port mode register setting and interrupt request flag clearing procedure. Interrupts masked. (Another possibility is to disable the relevant interrupt in interrupt enable register 1.) CCR I bit 1 Set port mode register bit Execute NOP instruction Clear interrupt request flag to 0 After setting the port mode register bit, first execute at least one instruction (e.g., NOP), then clear the interrupt request flag to 0 CCR I bit 0 Interrupt mask cleared Figure 3.4 Port Mode Register Setting and Interrupt Request Flag Clearing Procedure Rev. 1.00, 11/03, page 58 of 376 Section 4 Address Break The address break simplifies on-board program debugging. It requests an address break interrupt when the set break condition is satisfied. The interrupt request is not affected by the I bit of CCR. Break conditions that can be set include instruction execution at a specific address and a combination of access and data at a specific address. With the address break function, the execution start point of a program containing a bug is detected and execution is branched to the correcting program. Figure 4.1 shows a block diagram of the address break. Internal address bus Comparator BARH Interrupt generation control circuit BDRH BARL ABRKCR ABRKSR BDRL Internal data bus Interrupt Comparator [Legend] BARH, BARL: BDRH, BDRL: ABRKCR: ABRKSR: Break address register Break data register Address break control register Address break status register Figure 4.1 Block Diagram of Address Break 4.1 Register Descriptions Address break has the following registers. * Address break control register (ABRKCR) * Address break status register (ABRKSR) * Break address register (BARH, BARL) * Break data register (BDRH, BDRL) ABK0001A_000020020200 Rev. 1.00, 11/03, page 59 of 376 4.1.1 Address Break Control Register (ABRKCR) ABRKCR sets address break conditions. Bit 7 Bit Name RTINTE Initial Value 1 R/W R/W Description RTE Interrupt Enable When this bit is 0, the interrupt immediately after executing RTE is masked and then one instruction must be executed. When this bit is 1, the interrupt is not masked. 6 5 CSEL1 CSEL0 0 0 R/W R/W Condition Select 1 and 0 These bits set address break conditions. 00: Instruction execution cycle 01: CPU data read cycle 10: CPU data write cycle 11: CPU data read/write cycle 4 3 2 ACMP2 ACMP1 ACMP0 0 0 0 R/W R/W R/W Address Compare Condition Select 2 to 0 These bits comparison condition between the address set in BAR and the internal address bus. 000: Compares 16-bit addresses 001: Compares upper 12-bit addresses 010: Compares upper 8-bit addresses 011: Compares upper 4-bit addresses 1XX: Reserved (setting prohibited) 1 0 DCMP1 DCMP0 0 0 R/W R/W Data Compare Condition Select 1 and 0 These bits set the comparison condition between the data set in BDR and the internal data bus. 00: No data comparison 01: Compares lower 8-bit data between BDRL and data bus 10: Compares upper 8-bit data between BDRH and data bus 11: Compares 16-bit data between BDR and data bus [Legend] X: Don't care Rev. 1.00, 11/03, page 60 of 376 When an address break is set in the data read cycle or data write cycle, the data bus used will depend on the combination of the byte/word access and address. Table 4.1 shows the access and data bus used. When an I/O register space with an 8-bit data bus width is accessed in word size, a byte access is generated twice. For details on data widths of each register, see section 19.1, Register Addresses (Address Order). Table 4.1 Access and Data Bus Used Word Access Even Address Odd Address ROM space RAM space Upper 8 bits Upper 8 bits Lower 8 bits Lower 8 bits Upper 8 bits Lower 8 bits Byte Access Even Address Odd Address Upper 8 bits Upper 8 bits Upper 8 bits -- Upper 8 bits Upper 8 bits Upper 8 bits -- I/O register with 8-bit data bus Upper 8 bits width I/O register with 16-bit data bus width Upper 8 bits 4.1.2 Address Break Status Register (ABRKSR) ABRKSR consists of the address break interrupt flag and the address break interrupt enable bit. Bit 7 Bit Name ABIF Initial Value 0 R/W R/W Description Address Break Interrupt Flag [Setting condition] When the condition set in ABRKCR is satisfied [Clearing condition] When 0 is written after ABIF=1 is read 6 ABIE 0 R/W Address Break Interrupt Enable When this bit is 1, an address break interrupt request is enabled. 5 to 0 -- All 1 -- Reserved These bits are always read as 1. Rev. 1.00, 11/03, page 61 of 376 4.1.3 Break Address Registers (BARH, BARL) BARH and BARL are 16-bit read/write registers that set the address for generating an address break interrupt. When setting the address break condition to the instruction execution cycle, set the first byte address of the instruction. The initial value of this register is H'FFFF. 4.1.4 Break Data Registers (BDRH, BDRL) BDRH and BDRL are 16-bit read/write registers that set the data for generating an address break interrupt. BDRH is compared with the upper 8-bit data bus. BDRL is compared with the lower 8bit data bus. When memory or registers are accessed by byte, the upper 8-bit data bus is used for even and odd addresses in the data transmission. Therefore, comparison data must be set in BDRH for byte access. For word access, the data bus used depends on the address. See section 4.1.1, Address Break Control Register (ABRKCR), for details. The initial value of this register is undefined. Rev. 1.00, 11/03, page 62 of 376 4.2 Operation When the ABIF and ABIE bits in ABRKSR are set to 1, the address break function generates an interrupt request to the CPU. The ABIF bit in ABRKSR is set to 1 by the combination of the address set in BAR, the data set in BDR, and the conditions set in ABRKCR. When the interrupt request is accepted, interrupt exception handling starts after the instruction being executed ends. The address break interrupt is not masked because of the I bit in CCR of the CPU. The following figures show the operation examples of the address break interrupt setting. When the address break is specified in instruction execution cycle Register setting * ABRKCR = H'80 * BAR = H'025A Program 0258 * 025A 025C 0260 0262 : NOP NOP MOV.W @H'025A,R0 NOP NOP : Underline indicates the address to be stacked. NOP MOV MOV NOP instruc- instruc- instruc- instruction tion 2 Internal tion tion 1 prefetch prefetch prefetch prefetch processing Stack save Address bus Interrupt request 0258 025A 025C 025E SP-2 SP-4 Interrupt acceptance Figure 4.2 Address Break Interrupt Operation Example (1) Rev. 1.00, 11/03, page 63 of 376 When the address break is specified in the data read cycle Register setting * ABRKCR = H'A0 * BAR = H'025A Program 0258 025A * 025C 0260 0262 : NOP NOP MOV.W @H'025A,R0 NOP Underline indicates the address NOP to be stacked. : MOV MOV NOP MOV NOP Next instruc- instruc- instruc- instruc- instruc- instruction 1 tion 2 tion tion tion tion Internal Stack prefetch prefetch prefetch execution prefetch prefetch processing save Address bus Interrupt request 025C 025E 0260 025A 0262 0264 SP-2 Interrupt acceptance Figure 4.2 Address Break Interrupt Operation Example (2) Rev. 1.00, 11/03, page 64 of 376 Section 5 Clock Pulse Generators Clock oscillator circuitry (CPG: clock pulse generator) consists of an external oscillator, an internal RC oscillator, a duty correction circuit, a clock select circuit, and system clock dividers. Figure 5.1 shows a block diagram of the clock pulse generator. OSC1 OSC2 System clock oscillator OSC Duty correction circuit RC OSC /8 Clock select circuit Internal RC oscillator RC RC clock divider RC/2 RC/4 RC System clock divider /16 /32 /64 /2 to /8192 Prescaler S (13 bits) Figure 5.1 Block Diagram of Clock Pulse Generators The system clock () is a basic clock on which the CPU and on-chip peripheral modules operate. The system clock is divided into /2 to /8192 by prescaler S and the divided clocks are supplied to respective peripheral modules. CPG0200A_000020020200 Rev. 1.00, 11/03, page 65 of 376 5.1 Features * Choice of two clock sources Internal RC oscillator clock External oscillator clock * Choice of two types of RC oscillation frequency by the user software 8MHz 5% 10MHz 5% * Frequency trimming The initial frequency of the internal RC oscillator in the flash memory version is within the range shown above, so users do not need to trim the frequency. As for the masked ROM version (under planning), users can adjust the internal RC oscillation frequency to the range by rewriting the trimming registers. * Backup of the external oscillation halt This system detects the external oscillation halt. If detected, the system clock source is automatically switched to the internal RC oscillation clock. * Interrupt can be requested to the CPU when the system clock is changed from the external clock to the internal RC oscillator clock. Rev. 1.00, 11/03, page 66 of 376 5.2 Register Descriptions Clock oscillators are controlled by the following registers. * RC control register (RCCR) * RC trimming data protect register (RCTRMDPR) * RC trimming data register (RCTRMDR) * Clock control/status register (CKCSR) 5.2.1 RC Control Register (RCCR) RCCR controls the internal RC oscillator. Bit 7 Bit Name RCSTP Initial Value 0 R/W R/W Description Internal RC Oscillator Standby The internal RC oscillator standby state is entered by setting this bit to 1. 6 FSEL 0 R/W Frequency Select for Internal RC Oscillator 0: 8MHz 1: 10MHz 5 VCLSEL 0 R/W Power Supply Select for Internal RC Oscillator 0: Selects VBGR 1: Selects VCL When VCL is selected, the accuracy of the internal RC oscillator frequency cannot be guaranteed. 4 to 2 1 0 RCPSC1 RCPSC0 All 0 0 0 R/W R/W Reserved These bits are always read as 0 Division Ratio Select for Internal RC Oscillator The division ratio of RC changes right after rewriting this bit. These bits can be written to only when the CKSTA bit in CKCSR is 0. 0X: RC (not divided) 10: RC/2 11: RC/4 Rev. 1.00, 11/03, page 67 of 376 5.2.2 RC Trimming Data Protect Register (RCTRMDPR) RCTRMDPR controls RCTRMDPR itself and writing to RCTRMDR. Use the MOV instruction to rewrite this register. Bit manipulation instruction cannot change the settings. Bit 7 Bit Name WRI Initial Value 1 R/W W Description Write Inhibit Only when writing 0 to this bit, this register can be written to. This bit is always read as 1. 6 PRWE 0 R/W Protect Information Write Enable Bits 5 and 4 can be written to when this bit is set to 1. [Setting condition] * When writing 0 to the WRI bit and writing 1 to the PRWE bit Reset When writing 0 to the WRI bit and writing 0 to the PRWE bit [Clearing conditions] * * 5 LOCKDW 0 R/W Trimming Data Register Lock Down The RC trimming data register (RCTRMDR) cannot be written to when this bit is set to 1. Once this bit is set to 1, this register cannot be written to until a reset is input even if 0 is written to this bit. [Setting condition] When writing 0 to the WRI bit and writing 1 to the LOCKDW bit while the PRWE bit is 1 [Clearing condition] Reset 4 TRMDRWE 0 R/W Trimming Date Register Write Enable This register can be written to when the LOCKDW bit is 0 and this bit is 1. [Setting condition] * When writing 0 to the WRI bit while writing 1 to the LOCKDW bit while the PRWE bit is 1 Reset When writing 0 to the WRI bit and writing 0 to the LOCKDW bit while the PRWE bit is 1 [Clearing conditions] * * Rev. 1.00, 11/03, page 68 of 376 Bit 3 to 0 Bit Name Initial Value All 1 R/W Description Reserved These bits are always read as 1 5.2.3 RC Trimming Data Register (RCTRMDR) RCTRMDR stores the trimming data of the internal RC oscillator frequency. Bit 7 6 5 4 3 2 1 0 Bit Name TRMD7 TRMD6 TRMD5 TRMD4 TRMD3 TRMD2 TRMD1 TRMD0 Initial Value (0)* (0)* (0)* (0)* (0)* (0)* 0 0 R/W R/W R/W R/W R/W R/W R/W R R Description Trimming Data In the flash memory version, the trimming data is loaded from the flash memory to this register right after a reset. These bits are always read as undefined value. As for the masked ROM version (under planning), the internal RC oscillator frequency can be trimmed by rewriting these bits. The frequency generated in the internal RC oscillator changes right after rewriting these bits. These bits are initialized to H'00. Frequency variation is expressed as follows (the TRMD7 bit is a sign bit): (Min.) H'80 H'FC H'00 H'04 H'7C (Max.) Note: * These values are initialized while loading the trimming data from the flash memory in the flash memory version. 5.2.4 Clock Control/Status Register (CKCSR) CKCSR selects the port C function, controls switching the system clocks, and indicates the system clock state. Bit 7 6 Bit Name PMRC1 PMRC0 Initial Value 0 0 R/W R/W R/W Description Port C Function Select 1 and 2 PMRC1 PMRC0 PC1 0 1 0 1 0 0 1 1 I/O I/O OSC2 PC0 I/O OSC1 (external clock input) OSC1 CLKOUT I/O Rev. 1.00, 11/03, page 69 of 376 Bit 5 Bit Name Initial Value R/W R/W Description External Clock Backup Enable 0: External clock backup disabled 1: External clock backup enabled The detection circuit for the external clock is enabled when this bit is 1. When the external clock halt is detected while this LSI operates on the external clock, the system clock source is automatically switched to the internal RC oscillator regardless of the value of bit 4 in this register. Usage Note: The detection circuit for the external clock operates on the internal RC clock. When this bit is set to 1, do not set the internal RC oscillator to the standby state by the RCSTP bit in RCCR. OSCBAKE 0 4 OSCSEL 0 R/W LSI Operation Clock Select * When OSCBAKE = 0 This bit forcibly selects the system clock of this LSI. 0: Selects the internal RC clock as the system clock. 1: Selects the external clock as the system clock. * When OSCBAKE = 1 This bit switches the internal RC clock to the external clock. When this LSI operates on the internal RC clock, setting this bit to 1 switches the system clock to the external clock. [Setting condition] * * * When 1 is written to this bit while the CKSWIF bit is 0. When 0 is written to this bit When the external clock halt is detected while OSCBAKE = 1 [Clearing conditions] 3 CKSWIE 0 R/W Clock Switch Interrupt Enable Setting this bit to 1 enables the clock switch interrupt request. 2 CKSWIF 0 R/W Clock Switch Interrupt Request Flag [Setting condition] When the external clock is switched to the internal RC clock [Clearing condition] When writing 0 after reading 1 Rev. 1.00, 11/03, page 70 of 376 Bit 1 Bit Name OSCHLT Initial Value 1 R/W R Description External Clock Halt Detection Flag * When OSCBAKE = 1 This bit indicates the checking result of the external clock state. 0: External oscillation is in use 1: External oscillation is halted. * When OSCBAKE = 0 This bit is meaningless. This bit is always read as 1. 0 CKSTA 0 R LSI Operating Clock Status 0: This LSI operates on internal RC clock. 1: This LSI operates on external clock. 5.3 System Clock Select Operation Figure 5.2 shows the state transition of the system clock. LSI operates on internal RC clock Reset release Reset state RC oscillator: Operated External oscillator: Halted * Switching to external clock RC oscillator halted RC oscillator: Halted External oscillator: Operated RC oscillator operated LSI operates on external oscillator Note: * Conditions for the state transition are as follows: * When the external oscillation halt is detected while the backup function is enabled * When the external clock is switched to the internal RC clock by user software while the backup function is disabled RC oscillator: Operated External oscillator: Operated Figure 5.2 State Transition of System Clock Rev. 1.00, 11/03, page 71 of 376 5.3.1 Clock Control Operation The LSI system clock is generated by the internal RC clock after a reset. The internal RC clock is switched to the external clock by the user software. Figure 5.3 shows the flowchart to switch clocks with the external oscillator backup function enabled. Figures 5.4 and 5.5 show the flowcharts to switch clocks with the external oscillator backup function disabled. LSI operates on internal RC clock Start (reset) Write 1 to PMRC0 in CKCSR Write 1 to PMRC1 in CKCSR [1] Write 1 to OSCBAKE in CKCSR [2] Clear CKSWIE in CKCSR to 0 Write 1 to CKSWIE in CKCSR [3] Write 1 to OSCSEL in CKCSR [4] [5] Switched to external clock? (CKSTA in CKCSR is 1) No [1] External oscillation starts when pins PC1 and PC0 are selected as external oscillation pins. Write 0 to bit PMRC1 to input the external clock. [2] The external oscillation halt detection circuit is enabled when the external oscillation backup function is enabled. Since this detection circuit operates on the internal RC clock, do not set the internal RC oscillator to standby mode by using the RCSTP bit in RCCR. [3] An interrupt to switch the internal RC clock to the external clock is enabled. [4] After writing 1 to the OSCSEL bit, this LSI waits until the oscillation of the external oscillator settles. The correspondence between Nwait, which is the number of wait cycles for oscillation settling, and Nstby, which is the number of wait cycles for oscillation settling when returning from standby mode, is as follows: Nstby Nwait 2 x Nstby Nstby is set by bits STS[2:0] in SYSCR1. For details, see section 6.1.1, System Control Register 1 (SYSCR1). [5] While waiting for external oscillation settling, this LSI is not halted but continues to operate on the internal RC clock. Read the CKSTA bit in CKCSR to ensure whether or not clocks are switched. When the oscillation settles, this LSI switches the system clock to the external clock. If the external oscillation is in a halted state, then set the clock switch interrupt request flag. [6] If this LSI detects the external oscillation halt, it switches the system clock to the internal clock, and sets the clock switch interrupt request flag. External oscillation halt is detected LSI operates on internal RC clock Exceptional handling for clock switching Yes [6] LSI operates on external oscillator External oscillation halt is detected Figure 5.3 Flowchart of Clock Switching with Backup Function Enabled Rev. 1.00, 11/03, page 72 of 376 LSI operates on internal RC clock Start (reset) [1] External oscillation starts when pins PC1 and PC0 are selected as external oscillation pins. Write 0 to bit PMRC1 to input the external clock. [2] After writing 1 to the OSCSEL bit, this LSI waits until the oscillation of the external oscillator settles. The correspondence between Nwait, which is the number of wait cycles for oscillation settling, and Nstby, which is the number of wait cycles for oscillation settling when returning from standby mode, is as follows: Nstby Nwait 2 x Nstby Nstby is set by bits STS[2:0] in SYSCR1. For details, see section 6.1.1, System Control Register 1 (SYSCR1). [3] While the system is waiting for the external oscillation settling, this LSI is not halted but continues to operate on the internal RC clock. Read the value of the CKSTA bit in CKCSR to ensure that the system clocks are switched. Write 1 to PMRC0 in CKCSR Write 1 to PMRC1 in CKCSR [1] Write 0 to CKSWIE in CKCSR Write 1 to OSCSEL in CKCSR [2] Switched to external clock? (CKSTA in CKCSR is 1) [3] No Yes LSI operates on external oscillator Figure 5.4 Flowchart of Clock Switching with Backup Function Disabled (1) (From Internal RC Clock to External Clock) Rev. 1.00, 11/03, page 73 of 376 LSI operates on internal RC clock Start (LSI operates on internal RC clock) [1] When 0 is written to the OSCSEL bit, this LSI switches the external clock to the internal RC clock after the stop duration. Seven rising edges of the RC clock after the OSCSEL bit becomes 0 are included in the stop duration. [2] Writing 0 to PMRC0 stops the external oscillation. Write 0 to OSCBAKE in CKCSR Write 1 to CKSWIE in CKCSR if necessary Write 0 to OSCSEL in CKCSR [1] LSI operates on internal RC clock When CKSWIE = 1 Exception handling for clock switching Write 0 to PMRC0 in CKCSR if necessary [2] LSI operates on internal oscillator Figure 5.5 Flowchart of Clock Switching with Backup Function Disabled (2) (From External Clock to Internal RC Clock) Rev. 1.00, 11/03, page 74 of 376 5.3.2 Clock Change Timing The timing for changing clocks are shown in figures 5.6 to 5.8. OSC RC OSCSEL PHISTOP (Internal signal) CKSTA Internal RC clock operation Wait for external oscillation settling Nwait halt* External clock operation [Legend] OSC: External clock RC: Internal RC clock : System clock OSCSEL: Bit 4 in CKCSR PHISTOP: System clock stop control signal CKSTA: Bit 0 in CKCSR Note: * The halt duration is the duration from the timing when the clock stops to the first rising edge of the OSC clock after seven clock cycles of the RC clock have elapsed. Figure 5.6 Timing Chart of Switching Internal RC Clock to External Clock Rev. 1.00, 11/03, page 75 of 376 OSC RC OSCSEL PHISTOP (Internal signal) CKSTA CKSWIF External RC clock operation Wait for external oscillation settling Nwait halt* External clock operation [Legend] OSC: External clock RC: Internal RC clock : System clock OSCSEL: Bit 4 in CKCSR PHISTOP: System clock stop control signal CKSTA: Bit 0 in CKCSR CKSWIF: Bit 2 in CKCSR Note: * The halt duration is the duration from the timing when the clock stops to the seventh rising edge of the RC clock. Figure 5.7 Timing Chart to Switch External Clock to Internal RC Clock Rev. 1.00, 11/03, page 76 of 376 External clock halt OSC RC OSCHLT PHISTOP (Internal signal) CKSTA CKSWIF External RC clock operation OSC halt detected*1 Tchk halt*2 Internal clock operation [Legend] OSC: External clock RC: Internal RC clock : System clock OSCHLT: Bit 1 in CKCSR PHISTOP: System clock stop control signal CKSTA: Bit 0 in CKCSR CKSWIF: Bit 2 in CKCSR Notes: 1. 44 x RC Tchk 48 x RC 2. The halt duration is the duration from the timing when the clock stops to the seventh rising edge of the RC clock. Figure 5.8 External Oscillation Backup Timing Rev. 1.00, 11/03, page 77 of 376 5.4 Trimming of Internal RC Oscillator Frequency Users can trim the internal RC oscillator frequency, supplying the external reference pulses with the input capture function in internal timer W. An example of trimming flow and a timing chart are shown in figures 5.9 and 5.10, respectively. Because RCTRMDR is initialized by a reset, when users have trimmed the oscillators, some operations after a reset are necessary, such as trimming it again or saving the trimming value in an external device for later reloading. Start Setting timer W GRA: Input capture GRC: Buffer of GRA Set RCTRMD to H'00 Input reference pulses to pin P81/FTIOA Capture 1 Capture 2 Modify RCTRMDR* Frequency calculation Within desired frequency range? Yes No End Note: * Comparing the difference between the measured frequency and the desired frequency, individual bits of RCTRMDR are decided from the MSB bit by bit. Figure 5.9 Example of Trimming Flow for Internal RC Oscillator Frequency Rev. 1.00, 11/03, page 78 of 376 RC FTIOA input capture input tA (s) Timer W TCNT M-1 M M+1 M+ GRA N M M+ GRC N M Capture 1 Capture 2 Figure 5.10 Timing Chart of Trimming of Internal RC Oscillator Frequency The internal RC oscillator frequency is gained by the expression below. Since the input-capture input is sampled by the RC clock, the calculated result may include a sampling error of 1 cycle of the RC clock. RC = RC: tA: M: (M + ) - M tA Frequency of internal RC oscillator (MHz) Period of reference clock (s) Timer W counter value (MHz) Rev. 1.00, 11/03, page 79 of 376 5.5 External Oscillators This LSI has two methods to supply external clock pulses into it: connecting a crystal or ceramic resonator, and an external clock. Oscillation pins OSC1 and OSC2 are common with general ports PC0 and PC1, respectively. To set pins PC0 and PC1 as crystal resonator or external clock input ports, refer to section 5.3, System Clock Select Operation. 5.5.1 Connecting Crystal Resonator Figure 5.11 shows an example of connecting a crystal resonator. An AT-cut parallel-resonance crystal resonator should be used. Figure 5.12 shows the equivalent circuit of a crystal resonator. A resonator having the characteristics given in table 5.1 should be used. C1 PC0/OSC1 C2 PC1/OSC2/CLKOUT C1 = C 2 = 10 to 22 pF Figure 5.11 Example of Connection to Crystal Resonator LS RS CS PC0/OSC1 C0 PC1/OSC2/CLKOUT Figure 5.12 Equivalent Circuit of Crystal Resonator Table 5.1 Crystal Resonator Parameters Frequency (MHz) RS (Max.) C0 (Max.) 2 500 4 120 8 80 70 pF 10 60 Rev. 1.00, 11/03, page 80 of 376 5.5.2 Connecting Ceramic Resonator Figure 5.13 shows an example of connecting a ceramic resonator. C1 PC0/OSC1 C2 PC1/OSC2/CLKOUT C1 = C 2 = 5 to 30 pF Figure 5.13 Example of Connection to Ceramic Resonator 5.5.3 External Clock Input Method To use the external clock, input the external clock on pin OSC1. Figure 5.14 shows an example of connection. The duty cycle of the external clock signal must be 45 to 55%. PC0/OSC1 External clock input PC1/OSC2/CLKOUT General port Figure 5.14 Example of External Clock Input 5.6 5.6.1 Prescaler Prescaler S Prescaler S is a 13-bit counter using the system clock () as its input clock. The outputs, which are divided clocks, are used as internal clocks by the on-chip peripheral modules. Prescaler S is initialized to H'0000 by a reset, and starts counting on exit from the reset state. In standby mode and subsleep mode, the system clock pulse generator stops. Prescaler S also stops and is initialized to H'0000. It cannot be read from or written to by the CPU. The outputs from prescaler S is shared by the on-chip peripheral modules. The division ratio can be set separately for each on-chip peripheral module. In active mode and sleep mode, the clock input to prescaler S is a system clock with the division ratio specified by bits MA2 to MA0 in SYSCR2. Rev. 1.00, 11/03, page 81 of 376 5.7 5.7.1 Usage Notes Note on Resonators Resonator characteristics are closely related to board design and should be carefully evaluated by the user, referring to the examples shown in this section. Resonator circuit parameters will differ depending on the resonator element, stray capacitance of the PCB, and other factors. Suitable values should be determined in consultation with the resonator element manufacturer. Design the circuit so that the resonator element never receives voltages exceeding its maximum rating. 5.7.2 Notes on Board Design When using a crystal resonator (ceramic resonator), place the resonator and its load capacitors as close as possible to pins OSC1 and OSC2. Other signal lines should be routed away from the oscillator circuit to prevent induction from interfering with correct oscillation (see figure 5.15). Prohibited Signal A Signal B C1 PC0/OSC1 C2 PC1/OSC2/CLKOUT Figure 5.15 Example of Incorrect Board Design Rev. 1.00, 11/03, page 82 of 376 Section 6 Power-Down Modes For operating modes after a reset, this LSI has not only a normal active mode but also three power-down modes in which power consumption is significantly reduced. In addition, there is also a module standby function which reduces power consumption by individually stopping on-chip peripheral modules. * Active mode The CPU and all on-chip peripheral modules are operable on the system clock. The system clock frequency can be selected from osc, osc/8, osc/16, osc/32, and osc/64. * Sleep mode The CPU halts. On-chip peripheral modules are operable on the system clock. * Standby mode The CPU and all on-chip peripheral modules halt. * Subsleep mode The CPU and all on-chip peripheral modules halt. I/O ports keep the same states as before the transition. * Module standby function Independent of the above modes, power consumption can be reduced by halting on-chip peripheral modules that are not used in module units. LPW3003A_000020020200 Rev. 1.00, 11/03, page 83 of 376 6.1 Register Descriptions The registers related to power-down modes are listed below. * System control register 1 (SYSCR1) * System control register 2 (SYSCR2) * Module standby control register 1 (MSTCR1) * Module standby control register 2 (MSTCR2) 6.1.1 System Control Register 1 (SYSCR1) SYSCR1 controls the power-down modes, as well as SYSCR2. Bit 7 Bit Name SSBY Initial Value 0 R/W R/W Description Software Standby Specifies the operating mode to be entered after executing the SLEEP instruction. 0: Shifts to sleep mode. 1: Shifts to standby mode. For details, see table 6.2. 6 5 4 STS2 STS1 STS0 0 0 0 R/W R/W R/W Standby Timer Select 2 to 0 These bits set the wait time from when the system clock oscillator starts functioning until the clock is supplied, in shifting from standby mode, to active mode or sleep mode. During the wait time, this LSI automatically selects the internal RC clock as its system clock and counts the number of wait states. Select a wait time of 6.5 ms (oscillation stabilization time) or longer, depending on the operating frequency. Table 6.1 shows the relationship between the STS2 to STS0 values and the wait time. When using an external clock, set the wait time to be 100 s or longer in the F-ZTAT version. In the masked ROM version, the minimum value (STS2 = STS1 = STS0 = 1) is recommended. These bits also set the wait states for external oscillation stabilization when system clock is switched from the internal RC clock to the external clock by user software. The relationship between Nwait (number of wait states for oscillation stabilization) and Nstby (number of wait states for recovering to the standby mode) is as follows. Nstby Nwait 2 x Nstby Rev. 1.00, 11/03, page 84 of 376 Bit 3 to 0 Bit Name Initial Value All 0 R/W Description Reserved These bits are always read as 0. Table 6.1 Operating Frequency and Wait Time Operating Frequency 10 MHz 0.8 1.6 3.3 6.6 13.1 0.10 0.01 0.00 8 MHz 1.0 2.0 4.1 8.2 16.4 0.13 0.02 0.00 5 MHz 1.6 3.3 6.6 13.1 26.2 0.21 0.03 0.00 4 MHz 2.0 4.1 8.2 16.4 32.8 0.26 0.03 0.00 2.5 MHz 3.3 6.6 13.1 26.2 52.4 0.42 0.05 0.00 2 MHz 4.1 8.2 16.4 32.8 65.5 0.51 0.06 0.01 Bit Name STS2 STS1 STS0 Wait Time 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 8,192 states 16,384 states 32,768 states 65,536 states 131,072 states 1,024 states 128 states 16 states Notes: 1. Time unit is ms. 2. The internal RC clock counts the wait states, even when the external clock is used as system clock. Rev. 1.00, 11/03, page 85 of 376 6.1.2 System Control Register 2 (SYSCR2) SYSCR2 controls the power-down modes, as well as SYSCR1. Bit 7 Bit Name SMSEL Initial Value 0 R/W R/W Description Sleep Mode Selection This bit specifies the mode to be entered after executing the SLEEP instruction, as well as the SSBY bit in SYSCR1. For details, see table 6.2. 6 5 DTON 0 0 R/W Reserved This bit is always read as 0. Direct Transfer on Flag This bit specifies the mode to be entered after executing the SLEEP instruction, as well as the SSBY bit in SYSCR1. For details, see table 6.2. 4 3 2 MA2 MA1 MA0 0 0 0 R/W R/W R/W Active Mode Clock Select 2 to 0 These bits select the operating clock frequency in active and sleep modes. The operating clock frequency changes to the set frequency after the SLEEP instruction is executed. 0XX: 100: /8 101: /16 110: /32 111: /64 1, 0 All 0 Reserved These bits are always read as 0. [Legend] X: Don't care Rev. 1.00, 11/03, page 86 of 376 6.1.3 Module Standby Control Register 1 (MSTCR1) MSTCR1 allows the on-chip peripheral modules to enter a standby state in module units. Bit 7 6 5 4 Bit Name MSTIIC MSTS3 MSTAD Initial Value 0 0 0 0 R/W R/W R/W R/W Description Reserved This bit is always read as 0. IIC2 Module Standby IIC2 enters standby mode when this bit is set to 1. SCI3 Module Standby SCI3 enters standby mode when this bit is set to 1. A/D Converter Module Standby A/D converter enters standby mode when this bit is set to 1. 3 MSTWD 0 R/W Watchdog Timer Module Standby Watchdog timer enters standby mode when this bit is set to 1. (When the internal oscillator is selected for the watchdog timer clock, the watchdog timer operates regardless of the setting of this bit.) 2 1 0 MSTTW MSTTV 0 0 0 R/W R/W Timer W Module Standby Timer W enters standby mode when this bit is set to 1. Timer V Module Standby Timer V enters standby mode when this bit is set to 1. Reserved This bit is always read as 0. Rev. 1.00, 11/03, page 87 of 376 6.1.4 Module Standby Control Register 2 (MSTCR2) MSTCR2 allows the on-chip peripheral modules to enter a standby state in module units. Bit 7 to 5 4 3 to 0 Bit Name MSTTB1 Initial Value All 0 0 All 0 R/W R/W Description Reserved These bits are always read as 0. Timer B1 Module Standby Timer B1 enters standby mode when this bit is set to 1. Reserved These bits are always read as 0. Rev. 1.00, 11/03, page 88 of 376 6.2 Mode Transitions and States of LSI Figure 6.1 shows the possible transitions among these operating modes. A transition is made from the program execution state to the program halt state of the program by executing a SLEEP instruction. Interrupts allow for returning from the program halt state to the program execution state of the program. A direct transition from active mode to active mode changes the operating frequency. RES input enables transitions from a mode to the reset state. Table 6.2 shows the transition conditions of each mode after the SLEEP instruction is executed and a mode to return by an interrupt. Table 6.3 shows the internal states of the LSI in each mode. Reset state Program halt state SLEEP instruction Standby mode Interrupt Active mode Interrupt SLEEP instruction Program execution state Direct transition interrupt SLEEP instruction Sleep mode Program halt state Interrupt Subsleep mode Notes: 1. To make a transition to another mode by an interrupt, make sure interrupt handling is after the interrupt is accepted. 2. Details on the mode transition conditions are given in table 6.2. Figure 6.1 Mode Transition Diagram Table 6.2 DTON 0 Transition Mode after SLEEP Instruction Execution and Interrupt Handling SSBY 0 0 1 SMSEL 0 1 X 0* Transition Mode after SLEEP Transition Mode due to Instruction Execution Interrupt Sleep mode Subsleep mode Standby mode Active mode (direct transition) Active mode Active mode Active mode -- 1 X [Legend] X: Don't care Note: * When a state transition is performed while SMSEL is 1, timer V, SCI3, and the A/D converter are reset, and all registers are set to their initial values. To use these functions after entering active mode, reset the registers. Rev. 1.00, 11/03, page 89 of 376 Table 6.3 Function Internal State in Each Operating Mode Active Mode Functioning Functioning Functioning Functioning Functioning Sleep Mode Functioning Halted Retained Retained Retained Subsleep Mode Halted Halted Retained Retained Retained Standby Mode Halted Halted Retained Retained Register contents are retained, but output is the high-impedance state. Functioning Functioning Retained Reset Retained System clock oscillator CPU Instructions operations Registers RAM IO ports External interrupts IRQ3, IRQ0 WKP5 Functioning Functioning Functioning Functioning Functioning Functioning Functioning Functioning Functioning Functioning Functioning Functioning Functioning Functioning Retained Reset Retained Peripheral Timer B1 modules Timer V Timer W Watchdog timer SCI3 IIC2 A/D converter LVD Retained (Functioning if the internal oscillator is selected as a count clock.) Reset Retained Reset Functioning Reset Retained Reset Functioning Functioning Functioning Functioning Functioning Functioning Functioning Functioning Functioning 6.2.1 Sleep Mode In sleep mode, CPU operation is halted but the on-chip peripheral modules function at the clock frequency set by the MA2 to MA0 bits in SYSCR2. CPU register contents are retained. When an interrupt is requested, sleep mode is cleared and the CPU starts interrupt exception handling. Sleep mode is not cleared if the I bit in the condition code register (CCR) is set to 1 or the requested interrupt is disabled by the interrupt enable bit. When the RES pin is driven low in sleep mode, the CPU goes into the reset state and sleep mode is cleared. Rev. 1.00, 11/03, page 90 of 376 6.2.2 Standby Mode In standby mode, the system clock oscillator is halted, and operation of the CPU and on-chip peripheral modules is halted. However, as long as the rated voltage is supplied, the contents of CPU registers, on-chip RAM, and some on-chip peripheral module registers are retained. On-chip RAM contents will be retained as long as the voltage set by the RAM data retention voltage is provided. The I/O ports go to the high-impedance state. Standby mode is cleared by an interrupt. When an interrupt is requested, the internal RC oscillator starts functioning. The external oscillator also starts functioning when used. After the time set by the STS2 to STS0 bits in SYSCR1 has elapsed, standby mode is cleared and the CPU starts interrupt exception handling. Standby mode is not cleared if the I bit in the condition code register (CCR) is set to 1 or the requested interrupt is disabled by the interrupt enable bit. When the RES pin is driven low in standby mode, the internal RC oscillator starts functioning. The RC clock is supplied to the entire chip as soon as the internal RC oscillator starts functioning. The RES pin must be kept low for the rated period. On driving the RES pin high, after the oscillation stabilization time set by the power-on reset circuit has elapsed, the internal reset signal is cleared and the CPU starts reset exception handling. 6.2.3 Subsleep Mode In subsleep mode, the system clock oscillator is halted, and operation of the CPU and on-chip peripheral modules is halted. However, as long as the rated voltage is supplied, the contents of CPU registers, the on-chip RAM, and some on-chip peripheral module registers are retained. The I/O ports keep the same states as before the transition. Subsleep mode is cleared by an interrupt. When an interrupt is requested, the internal RC oscillator starts functioning. The external oscillator also starts functioning when used. After the time set by the STS2 to STS0 bits in SYSCR1 has elapsed, subsleep mode is cleared and the CPU starts interrupt exception handling. Subsleep mode is not cleared if the I bit in the condition code register (CCR) is set to 1 or the requested interrupt is disabled by the interrupt enable bit. When the RES pin is driven low in subsleep mode, the internal RC oscillator starts functioning. The RC clock is supplied to the entire chip as soon as the internal RC oscillator starts functioning. The RES pin must be kept low for the rated period. On driving the RES pin high, after the oscillation stabilization time set by the power-on reset circuit has elapsed, the internal reset signal is cleared and the CPU starts reset exception handling. Rev. 1.00, 11/03, page 91 of 376 6.3 Operating Frequency in Active Mode Operation in active mode is clocked at the frequency designated by the MA2 to MA0 bits in SYSCR2. The operating frequency changes to the set frequency after SLEEP instruction execution. 6.4 Direct Transition The CPU can execute programs in active mode. The operating frequency can be changed by making a transition directly from active mode to active mode. A direct transition can be made by executing a SLEEP instruction while the DTON bit in SYSCR2 is set to 1. If the direct transition interrupt is disabled by the interrupt enable register 1, a transition is made instead to sleep mode or subsleep mode. Note that if a direct transition is attempted while the I bit in condition code register (CCR) is set to 1, sleep mode or subsleep mode will be entered though that mode cannot be cleared by means of an interrupt. 6.5 Module Standby Function The module standby function can be set to any peripheral module. In module standby mode, the clock supply to the specified module stops and the module enters the power-down mode. Module standby mode enables each on-chip peripheral module to enter the standby state by setting a bit that corresponds to each module in MSTCR1 and MSTCR2 to 1 and cancels the mode by clearing the bit to 0. Rev. 1.00, 11/03, page 92 of 376 Section 7 ROM The features of the 12-kbyte (including 4 kbytes as the E7 control program area) flash memory built into the HD64F36912G and HD64F36902G are summarized below. * Programming/erase methods The flash memory is programmed in 64-byte units at a time. Erase is performed in singleblock units. The flash memory is configured as follows: 1 kbyte x 4 blocks and 4 kbytes x 2 blocks. To erase the entire flash memory, each block must be erased in turn. * Reprogramming capability The flash memory can be reprogrammed up to 1,000 times. * On-board programming On-board programming/erasing can be done in boot mode, in which the boot program built into the chip is started to erase or program of the entire flash memory. In normal user program mode, individual blocks can be erased or programmed. * Automatic bit rate adjustment For data transfer in boot mode, this LSI's bit rate can be automatically adjusted to match the transfer bit rate of the host. * Programming/erasing protection Sets software protection against flash memory programming/erasing. ROM3321A_000120030300 Rev. 1.00, 11/03, page 93 of 376 7.1 Block Configuration Figure 7.1 shows the block configuration of 12-kbyte flash memory. The thick lines indicate erasing units, the narrow lines indicate programming units, and the values are addresses. The flash memory is divided into 1 kbyte x 4 blocks and 4 kbytes x 2 blocks. Erasing is performed in these units. Programming is performed in 64-byte units starting from an address with lower eight bits H'00, H'40, H'80, or H'C0. Rev. 1.00, 11/03, page 94 of 376 H'0000 Erase unit 1 kbyte H'0040 H'0001 H'0041 H'0002 H'0042 Programming unit: 64 kbytes H'003F H'007F H'03C0 H'0400 Erase unit 1 kbyte H'0440 H'03C1 H'0401 H'0441 H'03C2 H'0402 H'0442 Programming unit: 64 kbytes H'03FF H'043F H'047F H'07C0 H'0800 Erase unit 1 kbyte H'0840 H'07C1 H'0801 H'0841 H'07C2 H'0802 H'0842 Programming unit: 64 kbytes H'07FF H'083F H'087F H'0BC0 H'0C00 Erase unit 1 kbyte H'0C40 H'0BC1 H'0C01 H'0C41 H'0BC2 H'0C02 H'0C42 Programming unit: 64 kbytes H'0BFF H'0C3F H'0C7F H'0FC0 H'1000 Erase unit 4 kbytes H'1040 H'0FC1 H'1001 H'1041 H'0FC2 H'1002 H'1042 Programming unit: 64 kbytes H'0FFF H'103F H'107F H'1FC0 H'2000 Erase unit 4 kbytes H'2040 H'1FC1 H'2001 H'2041 H'1FC2 H'2002 H'2042 Programming unit: 64 kbytes H'1FFF H'203F H'207F H'2FC0 H'2FC1 H'2FC2 H'2FFF Figure 7.1 Flash Memory Block Configuration Rev. 1.00, 11/03, page 95 of 376 7.2 Register Descriptions The flash memory has the following registers. * Flash memory control register 1 (FLMCR1) * Flash memory control register 2 (FLMCR2) * Erase block register 1 (EBR1) * Flash memory enable register (FENR) 7.2.1 Flash Memory Control Register 1 (FLMCR1) FLMCR1 is a register that makes the flash memory change to program mode, program-verify mode, erase mode, or erase-verify mode. For details on register setting, refer to section 7.4, Flash Memory Programming/Erasing. Bit 7 6 Bit Name -- SWE Initial Value 0 0 R/W -- R/W Description Reserved This bit is always read as 0. Software Write Enable When this bit is set to 1, flash memory programming/erasing is enabled. When this bit is cleared to 0, other FLMCR1 register bits and all EBR1 bits cannot be set. 5 ESU 0 R/W Erase Setup When this bit is set to 1, the flash memory changes to the erase setup state. When it is cleared to 0, the erase setup state is cancelled. Set this bit to 1 before setting the E bit to 1 in FLMCR1. 4 PSU 0 R/W Program Setup When this bit is set to 1, the flash memory changes to the program setup state. When it is cleared to 0, the program setup state is cancelled. Set this bit to 1 before setting the P bit in FLMCR1. 3 EV 0 R/W Erase-Verify When this bit is set to 1, the flash memory changes to erase-verify mode. When it is cleared to 0, erase-verify mode is cancelled. Rev. 1.00, 11/03, page 96 of 376 Bit 2 Bit Name PV Initial Value 0 R/W R/W Description Program-Verify When this bit is set to 1, the flash memory changes to program-verify mode. When it is cleared to 0, programverify mode is cancelled. 1 E 0 R/W Erase When this bit is set to 1 while SWE = 1 and ESU = 1, the flash memory changes to erase mode. When it is cleared to 0, erase mode is cancelled. 0 P 0 R/W Program When this bit is set to 1 while SWE = 1 and PSU = 1, the flash memory changes to program mode. When it is cleared to 0, program mode is cancelled. 7.2.2 Flash Memory Control Register 2 (FLMCR2) FLMCR2 is a register that displays the state of flash memory programming/erasing. FLMCR2 is a read-only register, and should not be written to. Bit 7 Bit Name FLER Initial Value 0 R/W R Description Flash Memory Error Indicates that an error has occurred during an operation on flash memory (programming or erasing). When FLER is set to 1, flash memory goes to the error-protection state. See 7.5.3, Error Protection, for details. 6 to 0 -- All 0 -- Reserved These bits are always read as 0. Rev. 1.00, 11/03, page 97 of 376 7.2.3 Erase Block Register 1 (EBR1) EBR1 specifies the flash memory erase area block. EBR1 is initialized to H'00 when the SWE bit in FLMCR1 is 0. Do not set more than one bit at a time, as this will cause all the bits in EBR1 to be automatically cleared to 0. Bit 7, 6 5 4 3 2 1 0 Bit Name -- EB5 EB4 EB3 EB2 EB1 EB0 Initial Value All 0 0 0 0 0 0 0 R/W -- R/W R/W R/W R/W R/W R/W Description Reserved These bits are always read as 0. When this bit is set to 1, 4 kbytes of H'2000 to H'2FFF will be erased. When this bit is set to 1, 4 kbytes of H'1000 to H'1FFF will be erased. When this bit is set to 1, 1 kbyte of H'0C00 to H'0FFF will be erased. When this bit is set to 1, 1 kbyte of H'0800 to H'0BFF will be erased. When this bit is set to 1, 1 kbyte of H'0400 to H'07FF will be erased. When this bit is set to 1, 1 kbyte of H'0000 to H'03FF will be erased. 7.2.4 Flash Memory Enable Register (FENR) Bit 7 (FLSHE) in FENR enables or disables the CPU access to the flash memory control registers, FLMCR1, FLMCR2, and EBR1. Bit 7 Bit Name FLSHE Initial Value 0 R/W R/W Description Flash Memory Control Register Enable Flash memory control registers can be accessed when this bit is set to 1. Flash memory control registers cannot be accessed when this bit is set to 0. 6 to 0 -- All 0 -- Reserved These bits are always read as 0. Rev. 1.00, 11/03, page 98 of 376 7.3 On-Board Programming Modes There is a mode for programming/erasing of the flash memory; boot mode, which enables onboard programming/erasing. On-board programming/erasing can also be performed in user program mode. At reset-start in reset mode, this LSI changes to a mode depending on the TEST pin settings, NMI pin settings, and input level of each port, as shown in table 7.1. The input level of each pin must be defined four states before the reset ends. When changing to boot mode, the boot program built into this LSI is initiated. The boot program transfers the programming control program from the externally-connected host to on-chip RAM via SCI3. After erasing the entire flash memory, the programming control program is executed. This can be used for programming initial values in the on-board state or for a forcible return when programming/erasing can no longer be done in user program mode. In user program mode, individual blocks can be erased and programmed by branching to the user program/erase control program prepared by the user. Table 7.1 TEST 0 0 Setting Programming Modes NMI 1 0 P85 X 1 LSI State after Reset End User mode Boot mode [Legend] X: Don't care 7.3.1 Boot Mode Table 7.2 shows the boot mode operations between reset end and branching to the programming control program. 1. When boot mode is used, the flash memory programming control program must be prepared in the host beforehand. Prepare a programming control program in accordance with the description in section 7.4, Flash Memory Programming/Erasing. 2. SCI3 should be set to asynchronous mode, and the transfer format as follows: 8-bit data, 1 stop bit, and no parity. 3. When the boot program is initiated, the chip measures the low-level period of asynchronous SCI communication data (H'00) transmitted continuously from the host. The chip then calculates the bit rate of transmission from the host, and adjusts the SCI3 bit rate to match that of the host. The reset should end with the RxD pin high. The RxD and TxD pins should be pulled up on the board if necessary. After the reset is complete, it takes approximately 100 states before the chip is ready to measure the low-level period. Rev. 1.00, 11/03, page 99 of 376 4. After matching the bit rates, the chip transmits one H'00 byte to the host to indicate the completion of bit rate adjustment. The host should confirm that this adjustment end indication (H'00) has been received normally, and transmit one H'55 byte to the chip. If reception could not be performed normally, initiate boot mode again by a reset. Depending on the host's transfer bit rate and system clock frequency of this LSI, there will be a discrepancy between the bit rates of the host and the chip. To operate the SCI properly, set the host's transfer bit rate and system clock frequency of this LSI within the ranges listed in table 7.3. 5. In boot mode, a part of the on-chip RAM area is used by the boot program. The area H'F980 to H'FEEF is the area to which the programming control program is transferred from the host. The boot program area cannot be used until the execution state in boot mode switches to the programming control program. 6. Before branching to the programming control program, the chip terminates transfer operations by SCI3 (by clearing the RE and TE bits in SCR3 to 0), however the adjusted bit rate value remains set in BRR. Therefore, the programming control program can still use it for transfer of write data or verify data with the host. The TxD pin is high (PCR22 = 1, P22 = 1). The contents of the CPU general registers are undefined immediately after branching to the programming control program. These registers must be initialized at the beginning of the programming control program, as the stack pointer (SP), in particular, is used implicitly in subroutine calls, etc. 7. Boot mode can be cleared by a reset. End the reset after driving the reset pin low, waiting at least 20 states, and then setting the TEST pin and NMI pin. Boot mode is also cleared when a WDT overflow occurs. 8. Do not change the TEST pin and NMI pin input levels in boot mode. Rev. 1.00, 11/03, page 100 of 376 Table 7.2 Item Boot Mode Operation Host Operation Processing Contents Communication Contents LSI Operation Processing Contents Branches to boot program at reset-start. Boot mode initiation Boot program initiation Bit rate adjustment Continuously transmits data H'00 at specified bit rate. H'00, H'00 . . . H'00 Transmits data H'55 when data H'00 is received error-free. H'00 * Measures low-level period of receive data H'00. * Calculates bit rate and sets BRR in SCI3. * Transmits data H'00 to host as adjustment end indication. H'55 reception. H'55 Flash memory erase Boot program erase error H'FF H'AA reception H'AA Checks flash memory data, erases all flash memory blocks in case of written data existing, and transmits data H'AA to host. (If erase could not be done, transmits data H'FF to host and aborts operation.) Transfer of number of bytes of programming control program Transmits number of bytes (N) of programming control program to be transferred as 2-byte data (low-order byte following high-order byte) Upper bytes, lower bytes Echoback Echobacks the 2-byte data received to host. Transmits 1-byte of programming control program (repeated for N times) H'XX Echoback Echobacks received data to host and also transfers it to RAM. (repeated for N times) H'AA reception H'AA Transmits data H'AA to host. Branches to programming control program transferred to on-chip RAM and starts execution. Rev. 1.00, 11/03, page 101 of 376 Table 7.3 System Clock Frequencies for which Automatic Adjustment of LSI Bit Rate is Possible System Clock Frequency Range of LSI 8 to 10 MHz 4 to 10 MHz 2 to 10 MHz Host Bit Rate 9,600 bps 4,800 bps 2,400 bps 7.3.2 Programming/Erasing in User Program Mode On-board programming/erasing of an individual flash memory block can also be performed in user program mode by branching to a user program/erase control program. The user must set branching conditions and provide on-board means of supplying programming data. The flash memory must contain the user program/erase control program or a program that provides the user program/erase control program from external memory. As the flash memory itself cannot be read during programming/erasing, transfer the user program/erase control program to on-chip RAM, as in boot mode. Figure 7.2 shows a sample procedure for programming/erasing in user program mode. Prepare a user program/erase control program in accordance with the description in section 7.4, Flash Memory Programming/Erasing. Reset-start No Program/erase? Yes Transfer user program/erase control program to RAM Branch to flash memory application program Branch to user program/erase control program in RAM Execute user program/erase control program (flash memory rewrite) Branch to flash memory application program Figure 7.2 Programming/Erasing Flowchart Example in User Program Mode Rev. 1.00, 11/03, page 102 of 376 7.4 Flash Memory Programming/Erasing A software method using the CPU is employed to program and erase flash memory in the onboard programming modes. Depending on the FLMCR1 setting, the flash memory operates in one of the following four modes: Program mode, program-verify mode, erase mode, and erase-verify mode. The programming control program in boot mode and the user program/erase control program in user program mode use these operating modes in combination to perform programming/erasing. Flash memory programming and erasing should be performed in accordance with the descriptions in section 7.4.1, Program/Program-Verify and section 7.4.2, Erase/Erase-Verify, respectively. 7.4.1 Program/Program-Verify When writing data or programs to the flash memory, the program/program-verify flowchart shown in figure 7.3 should be followed. Performing programming operations according to this flowchart will enable data or programs to be written to the flash memory without subjecting the chip to voltage stress or sacrificing program data reliability. 1. Programming must be done to an empty address. Do not reprogram an address to which programming has already been performed. 2. Programming should be carried out 64 bytes at a time. A 64-byte data transfer must be performed even if writing fewer than 64 bytes. In this case, H'FF data must be written to the extra addresses. 3. Prepare the following data storage areas in RAM: A 64-byte programming data area, a 64-byte reprogramming data area, and a 64-byte additional-programming data area. Perform reprogramming data computation according to table 7.4, and additional programming data computation according to table 7.5. 4. Consecutively transfer 64 bytes of data in byte units from the reprogramming data area or additional-programming data area to the flash memory. The program address and 64-byte data are latched in the flash memory. The lower 8 bits of the start address in the flash memory destination area must be H'00, H'40, H'80, or H'C0. 5. The time during which the P bit is set to 1 is the programming time. Table 7.6 shows the allowable programming times. 6. The watchdog timer (WDT) is set to prevent overprogramming due to program runaway, etc. An overflow cycle of approximately 6.6 ms is allowed. 7. 8. For a dummy write to a verify address, write 1-byte data H'FF to an even address. Verify data can be read in words from the address to which a dummy write was performed. The maximum number of repetitions of the program/program-verify sequence of the same bit is 1,000. Rev. 1.00, 11/03, page 103 of 376 START Write pulse application subroutine Disable WDT Apply Write Pulse WDT enable Set PSU bit in FLMCR1 Wait 50 s Set P bit in FLMCR1 Wait (Wait time = Programming time) Clear P bit in FLMCR1 Wait 5 s Clear PSU bit in FLMCR1 Wait 5 s Disable WDT *2 Set SWE bit in FLMCR1 Wait 1 s *1 Store 64-byte program data in program data area and reprogram data area n=1 m= 0 Write 64-byte data in RAM reprogram data area consecutively to flash memory Apply Write pulse Set PV bit in FLMCR1 Wait 4 s Set block start address as verify address nn+1 H'FF dummy write to verify address End Sub Wait 2 s Read verify data Increment address Verify data = Write data? *1 No m=1 No Yes n6? Yes Additional-programming data computation Reprogram data computation No 64-byte data verification completed? Yes Clear PV bit in FLMCR1 Wait 2 s n 6? Yes Successively write 64-byte data from additionalprogramming data area in RAM to flash memory Sub-Routine-Call Apply Write Pulse No Yes No m=0? Yes Clear SWE bit in FLMCR1 Wait 100 s End of programming n 1000 ? No Clear SWE bit in FLMCR1 Wait 100 s Programming failure Notes: 1. The RTS instruction must not be used during the following (1) and (2) periods. (1) A period between 64-byte data programming to flash memory and the P bit clearing (2) A period between dummy writing of H'FF to a verify address and verify data reading 2. When WDT is in use, disable it once. Figure 7.3 Program/Program-Verify Flowchart Rev. 1.00, 11/03, page 104 of 376 Table 7.4 Reprogram Data Computation Table Verify Data 0 1 0 1 Reprogram Data 1 0 1 1 Comments Programming completed Reprogram bit -- Remains in erased state Program Data 0 0 1 1 Table 7.5 Additional-Program Data Computation Table Verify Data 0 1 0 1 Additional-Program Data 0 1 1 1 Comments Additional-program bit No additional programming No additional programming No additional programming Reprogram Data 0 0 1 1 Table 7.6 Programming Time In Additional Programming 10 -- Comments n Programming (Number of Writes) Time 1 to 6 7 to 1,000 30 200 Note: Time shown in s. 7.4.2 Erase/Erase-Verify When erasing flash memory, the erase/erase-verify flowchart shown in figure 7.4 should be followed. 1. Prewriting (setting erase block data to all 0s) is not necessary. 2. Erasing is performed in block units. Make only a single-bit specification in the erase block register (EBR1). To erase multiple blocks, each block must be erased in turn. 3. The time during which the E bit is set to 1 is the flash memory erase time. 4. The watchdog timer (WDT) is set to prevent overerasing due to program runaway, etc. An overflow cycle of approximately 19.8 ms is allowed. 5. For a dummy write to a verify address, write 1-byte data H'FF to an even address. Verify data can be read in words from the address to which a dummy write was performed. Rev. 1.00, 11/03, page 105 of 376 6. If the read data is not erased successfully, set erase mode again, and repeat the erase/eraseverify sequence as before. The maximum number of repetitions of the erase/erase-verify sequence is 100. 7.4.3 Interrupt Handling when Programming/Erasing Flash Memory All interrupts, including the NMI interrupt, are disabled while flash memory is being programmed or erased, or while the boot program is executing, for the following three reasons: 1. Interrupt during programming/erasing may cause a violation of the programming or erasing algorithm, with the result that normal operation cannot be assured. 2. If interrupt exception handling starts before the vector address is written or during programming/erasing, a correct vector cannot be fetched and the CPU malfunctions. 3. If an interrupt occurs during boot program execution, normal boot mode sequence cannot be carried out. Rev. 1.00, 11/03, page 106 of 376 Erase start Disable WDT SWE bit 1 Wait 1 s n1 Set EBR1 Enable WDT ESU bit 1 Wait 100 s E bit 1 Wait 10 s E bit 0 Wait 10 s ESU bit 10 Wait 10 s Disable WDT EV bit 1 Wait 20 s Set block start address as verify address *2 H'FF dummy write to verify address Wait 2 s Read verify data No Increment address Verify data + all 1s ? Yes *1 nn+1 No Last address of block ? Yes EV bit 0 Wait 4 s EV bit 0 Wait 4s No All erase block erased ? Yes Yes SWE bit 0 Wait 100 s End of erasing n 100 ? No Yes SWE bit 0 Wait 100 s Erase failure Notes: 1. The RTS instruction must not be used during a period between dummy writing of H'FF to a verify address and verify data reading. 2. When WDT is in use, disable it once. Figure 7.4 Erase/Erase-Verify Flowchart Rev. 1.00, 11/03, page 107 of 376 7.5 Program/Erase Protection There are three kinds of flash memory program/erase protection; hardware protection, software protection, and error protection. 7.5.1 Hardware Protection Hardware protection refers to a state in which programming/erasing of flash memory is forcibly disabled or aborted because of a transition to reset, subsleep mode or standby mode. Flash memory control register 1 (FLMCR1), flash memory control register 2 (FLMCR2), and erase block register 1 (EBR1) are initialized. In a reset via the RES pin, the reset state is not entered unless the RES pin is held low until oscillation stabilizes after powering on. In the case of a reset during operation, hold the RES pin low for the RES pulse width specified in the AC Characteristics section. 7.5.2 Software Protection Software protection can be implemented against programming/erasing of all flash memory blocks by clearing the SWE bit in FLMCR1. When software protection is in effect, setting the P or E bit in FLMCR1 does not cause a transition to program mode or erase mode. By setting the erase block register 1 (EBR1), erase protection can be set for individual blocks. When EBR1 is set to H'00, erase protection is set for all blocks. 7.5.3 Error Protection In error protection, an error is detected when CPU runaway occurs during flash memory programming/erasing, or operation is not performed in accordance with the program/erase algorithm, and the program/erase operation is aborted. Aborting the program/erase operation prevents damage to the flash memory due to overprogramming or overerasing. When the following errors are detected during programming/erasing of flash memory, the FLER bit in FLMCR2 is set to 1, and the error protection state is entered. * When the flash memory of the relevant address area is read during programming/erasing (including vector read and instruction fetch) * Immediately after exception handling excluding a reset during programming/erasing * When a SLEEP instruction is executed during programming/erasing The FLMCR1, FLMCR2, and EBR1 settings are retained, however program mode or erase mode is aborted at the point at which the error occurred. Program mode or erase mode cannot be reentered by re-setting the P or E bit. However, PV and EV bit setting is enabled, and a transition can be made to verify mode. Error protection can be cleared only by a reset. Rev. 1.00, 11/03, page 108 of 376 Section 8 RAM The H8/36912F and H8/36902F have 1536 bytes, the H8/36912 and H8/36902 have 512 bytes, and the H8/36911, H8/36901, and H8/36900 have 256 bytes of on-chip high-speed static RAM, respectively. The RAM is connected to the CPU by a 16-bit data bus, enabling two-state access by the CPU to both byte data and word data. Product Classification Flash memory version Masked ROM version H8/36912F H8/36902F H8/36912, H8/36902 H8/36911, H8/36901 H8/36900 Note: * RAM Size 1536 bytes 1536 bytes 512 bytes 256 bytes 256 bytes RAM Address H'F980 to H'FF7F* H'F980 to H'FF7F* H'FD80 to H'FF7F H'FE80 to H'FF7F H'FE80 to H'FF7F When the E7 is used, area H'F980 to H'FD7F must not be accessed. RAM0400A_000020020200 Rev. 1.00, 11/03, page 109 of 376 Rev. 1.00, 11/03, page 110 of 376 Section 9 I/O Ports The LSI of the H8/36912 Group and H8/36902 Group has 18 general I/O ports. Port 8 (P84 to P80) is a large current port, which can drive 20 mA (@VOL = 1.5 V) when a low level signal is output. Any of these ports can become an input port immediately after a reset. They can also be used as I/O pins of the on-chip peripheral modules or external interrupt input pins, and these functions can be switched depending on the register settings. The registers for selecting these functions can be divided into two types: those included in I/O ports and those included in each onchip peripheral module. General I/O ports are comprised of the port control register for controlling inputs/outputs and the port data register for storing output data and can select inputs/outputs in bit units. For functions in each port, see Appendix B.1, I/O Port Block Diagrams. For the execution of bit manipulation instructions to the port control register and port data register, see section 2.8.3, Bit Manipulation Instruction. 9.1 Port 1 Port 1 is a general I/O port also functioning as an IRQ interrupt input pin and timer V input pin. Figure 9.1 shows its pin configuration. Port 1 P17/ P14/ /TRGV Figure 9.1 Port 1 Pin Configuration Port 1 has the following registers. * Port mode register 1 (PMR1) * Port control register 1 (PCR1) * Port data register 1 (PDR1) * Port pull-up control register 1 (PUCR1) Rev. 1.00, 11/03, page 111 of 376 9.1.1 Port Mode Register 1 (PMR1) PMR1 switches the functions of pins in port 1 and port 2. Bit 7 Bit Name IRQ3 Initial Value 0 R/W R/W Description P17/IRQ3/TRGV Pin Function Switch Selects whether pin P17/IRQ3/TRGV is used as P17 or as IRQ3/TRGV. 0: General I/O port 1: IRQ3/TRGV input pin 6, 5 4 IRQ0 All 0 0 R/W Reserved These bits are always read as 0. P14/IRQ0 Pin Function Switch Selects whether pin P14/IRQ0 is used as P14 or as IRQ0. 0: General I/O port 1: IRQ0 input pin 3, 2 1 TXD All 0 0 R/W Reserved These bits are always read as 0. P22/TXD Pin Function Switch Selects whether pin P22/TXD is used as P22 or as TXD. 0: General I/O port 1: TXD output pin 0 0 Reserved This bit is always read as 0. Rev. 1.00, 11/03, page 112 of 376 9.1.2 Port Control Register 1 (PCR1) PCR1 selects inputs/outputs in bit units for pins to be used as general I/O ports of port 1. Bit 7 6 5 4 3 2 1 0 Bit Name PCR17 PCR14 Initial Value 0 0 R/W W W Description When the corresponding pin is designated in PMR1 as a general I/O pin, setting a PCR1 bit to 1 makes the corresponding pin an output port, while clearing the bit to 0 makes the pin an input port. Bits 6, 5, and 3 to 0 are reserved. 9.1.3 Port Data Register 1 (PDR1) PDR1 is a general I/O port data register of port 1. Bit 7 6 5 4 3 2 1 0 Bit Name P17 P14 Initial Value 0 1 1 0 1 1 1 1 R/W R/W R/W Description These bits store output data for port 1 pins. If PDR1 is read while PCR1 bits are set to 1, the value stored in PDR1 are read. If PDR1 is read while PCR1 bits are cleared to 0, the pin states are read regardless of the value stored in PDR1. Bits 6, 5, and 3 to 0 are reserved. These bits are always read as 1. Rev. 1.00, 11/03, page 113 of 376 9.1.4 Port Pull-Up Control Register 1 (PUCR1) PUCR1 controls the pull-up MOS in bit units of the pins set as the input ports. Bit 7 6 5 4 3 2 1 0 Bit Name PUCR17 PUCR14 Initial Value 0 1 1 0 1 1 1 1 R/W R/W R/W Description Only bits for which PCR1 is cleared are valid. The pull-up MOS of the P17 and P14 pins enter the onstate when these bits are set to 1, while they enter the off-state when these bits are cleared to 0. Bits 6, 5, and 3 to 0 are reserved. These bits are always read as 1. 9.1.5 Pin Functions The correspondence between the register specification and the port functions is shown below. * P17/IRQ3/TRGV pin Register Bit Name PMR1 IRQ3 PCR1 PCR17 0 1 1 [Legend] X: Don't care X Pin Function P17 input pin P17 output pin IRQ3 input/TRGV input pin Setting value 0 * P14/IRQ0 pin Register Bit Name PMR1 IRQ0 PCR1 PCR14 0 1 1 [Legend] X: Don't care X Pin Function P14 input pin P14 output pin IRQ0 input pin Setting value 0 Rev. 1.00, 11/03, page 114 of 376 9.2 Port 2 Port 2 is a general I/O port also functioning as a SCI3 I/O pin. Each pin of the port 2 is shown in figure 9.2. The register settings of PMR1 and SCI3 have priority for functions of the pins for both uses. P22/TXD Port 2 P21/RXD P20/SCK3 Figure 9.2 Port 2 Pin Configuration Port 2 has the following registers. * Port control register 2 (PCR2) * Port data register 2 (PDR2) 9.2.1 Port Control Register 2 (PCR2) PCR2 selects inputs/outputs in bit units for pins to be used as general I/O ports of port 2. Bit 7 to 3 2 1 0 Bit Name PCR22 PCR21 PCR20 Initial Value 0 0 0 R/W W W W Description Reserved When each of the port 2 pins, P22 to P20, functions as an general I/O port, setting a PCR2 bit to 1 makes the corresponding pin an output port, while clearing the bit to 0 makes the pin an input port. Rev. 1.00, 11/03, page 115 of 376 9.2.2 Port Data Register 2 (PDR2) PDR2 is a general I/O port data register of port 2. Bit 7 to 3 2 1 0 Bit Name P22 P21 P20 Initial Value All 1 0 0 0 R/W R/W R/W R/W Description Reserved These bits are always read as 1. These bits store output data for port 2 pins. If PDR2 is read while PCR2 bits are set to 1, the value stored in PDR2 is read. If PDR2 is read while PCR2 bits are cleared to 0, the pin states are read regardless of the value stored in PDR2. 9.2.3 Pin Functions The correspondence between the register specification and the port functions is shown below. * P22/TXD pin Register Bit Name Setting value PMR1 TXD 0 PCR2 PCR22 0 1 1 [Legend] X: Don't care X Pin Function P22 input pin P22 output pin TXD output pin * P21/RXD pin Register Bit Name Setting value SCR3 RE 0 PCR2 PCR21 0 1 1 [Legend] X: Don't care X Pin Function P21 input pin P21 output pin RXD input pin Rev. 1.00, 11/03, page 116 of 376 * P20/SCK3 pin Register Bit Name SCR3 CKE1 CKE0 0 0 1 X SMR COM 0 1 X X PCR2 PCR20 0 1 0 0 1 [Legend] X: Don't care X X X Pin Function P20 input pin P20 output pin SCK3 output pin SCK3 output pin SCK3 input pin Setting value 0 9.3 Port 5 Port 5 is a general I/O port also functioning as an I2C bus interface I/O pin*, A/D trigger input pin, and wakeup interrupt input pin. Each pin of the port 5 is shown in figure 9.3. The register setting of the I2C bus interface has priority for functions of the P57/SCL and P56/SDA pins. Note: * Supported only by the H8/36912 Group. P57/SCL Port 5 P56/SDA P55/ / Figure 9.3 Port 5 Pin Configuration Port 5 has the following registers. * Port mode register 5 (PMR5) * Port control register 5 (PCR5) * Port data register 5 (PDR5) * Port pull-up control register 5 (PUCR5) Rev. 1.00, 11/03, page 117 of 376 9.3.1 Port Mode Register 5 (PMR5) PMR5 switches the functions of pins in port 5. Bit 7, 6 5 Bit Name WKP5 Initial Value All 0 0 R/W R/W Description Reserved These bits are always read as 0. P55/WKP5/ADTRG Pin Function Switch Selects whether pin P55/WKP5/ADTRG is used as P55 or as WKP5/ADTRG. 0: General I/O port 1: WKP5/ADTRG input pin 4 to 0 All 0 Reserved These bits are always read as 0. 9.3.2 Port Control Register 5 (PCR5) PCR5 selects inputs/outputs in bit units for pins to be used as general I/O ports of port 5. Bit 7 6 5 4 to 0 Bit Name PCR57 PCR56 PCR55 Initial Value 0 0 0 R/W W W W Description When each of the port 5 pins, P57 to P55, functions as an general I/O port, setting a PCR5 bit to 1 makes the corresponding pin an output port, while clearing the bit to 0 makes the pin an input port. Reserved Rev. 1.00, 11/03, page 118 of 376 9.3.3 Port Data Register 5 (PDR5) PDR5 is a general I/O port data register of port 5. Bit 7 6 5 Bit Name P57 P56 P55 Initial Value 0 0 0 R/W R/W R/W R/W Description These bits store output data for port 5 pins. If PDR5 is read while PCR5 bits are set to 1, the value stored in PDR5 are read. If PDR5 is read while PCR5 bits are cleared to 0, the pin states are read regardless of the value stored in PDR5. Reserved These bits are always read as 1. 4 to 0 All 1 9.3.4 Port Pull-Up Control Register 5 (PUCR5) PUCR5 controls the pull-up MOS in bit units of the pins set as the input ports. Bit 7, 6 5 Bit Name PUCR55 Initial Value All 0 0 R/W R/W Description Reserved These bits are always read as 0. Only bits for which PCR5 is cleared are valid. The pull-up MOS of the corresponding pins enter the onstate when this bit is set to 1, while they enter the offstate when this bit is cleared to 0. 4 to 0 All 0 Reserved These bits are always read as 0. Rev. 1.00, 11/03, page 119 of 376 9.3.5 Pin Functions The correspondence between the register specification and the port functions is shown below. * P57/SCL pin Register Bit Name ICCR ICE PCR5 PCR57 0 1 1 X Pin Function P57 input pin P57 output pin SCL I/O pin* Setting value 0 [Legend] X: Don't care Note: As the SCL output form is NMOS open-drain, direct bus drive is enabled. * Supported only by the H8/36912 Group. * P56/SDA pin Register Bit Name ICCR ICE PCR5 PCR56 0 1 1 X Pin Function P56 input pin P56 output pin SDA I/O pin* Setting value 0 [Legend] X: Don't care Note: As the SDA output form is NMOS open-drain, direct bus drive is enabled. * Supported only by the H8/36912 Group. * P55/WKP5/ADTRG pin Register Bit Name PMR5 WKP5 PCR5 PCR55 0 1 1 [Legend] X: Don't care X Pin Function P55 input pin P55 output pin WKP5/ADTRG input pin Setting value 0 Rev. 1.00, 11/03, page 120 of 376 9.4 Port 7 Port 7 is a general I/O port also functioning as a timer V I/O pin. Each pin of the port 7 is shown in figure 9.4. The register setting of TCSRV in timer V has priority for functions of the P76/TMOV pin. The pins, P75/TMCIV and P74/TMRIV, are also functioning as timer V input ports that are connected to the timer V regardless of the register setting of port 7. P76/TMOV Port 7 P75/TMCIV P74/TMRIV Figure 9.4 Port 7 Pin Configuration Port 7 has the following registers. * Port control register 7 (PCR7) * Port data register 7 (PDR7) 9.4.1 Port Control Register 7 (PCR7) PCR7 selects inputs/outputs in bit units for pins to be used as general I/O ports of port 7. Bit 7 6 5 4 3 to 0 Bit Name PCR76 PCR75 PCR74 Initial Value 0 0 0 R/W W W W Description Reserved Setting a PCR7 bit to 1 makes the corresponding pin an output port, while clearing the bit to 0 makes the pin an input port. Note that the TCSRV setting of the timer V has priority for deciding input/output direction of the P76/TMOV pin. Reserved Rev. 1.00, 11/03, page 121 of 376 9.4.2 Port Data Register 7 (PDR7) PDR7 is a general I/O port data register of port 7. Bit 7 6 5 4 Bit Name P76 P75 P74 Initial Value 1 0 0 0 R/W R/W R/W R/W Description Reserved This bit is always read as 1. These bits store output data for port 7 pins. If PDR7 is read while PCR7 bits are set to 1, the value stored in PDR7 is read. If PDR7 is read while PCR7 bits are cleared to 0, the pin states are read regardless of the value stored in PDR7. Reserved These bits are always read as 1. 3 to 0 All 1 9.4.3 Pin Functions The correspondence between the register specification and the port functions is shown below. * P76/TMOV pin Register Bit Name TCSRV PCR7 Pin Function P76 input pin P76 output pin TMOV output pin 0 1 Other than the above values [Legend] X: Don't care X OS3 to OS0 PCR76 Setting value 0000 * P75/TMCIV pin Register Bit Name PCR7 PCR75 1 Pin Function P75 input/TMCIV input pin P75 output/TMCIV input pin Setting value 0 Rev. 1.00, 11/03, page 122 of 376 * P74/TMRIV pin Register Bit Name PCR7 PCR74 1 Pin Function P74 input/TMRIV input pin P74 output/TMRIV input pin Setting value 0 9.5 Port 8 Port 8 is a general I/O port also functioning as a timer W I/O pin. Each pin of the port 8 is shown in figure 9.5. The register setting of the timer W has priority for functions of the P84/FTIOD, P83/FTIOC, P82/FTIOB, and P81/FTIOA pins. The P80/FTCI pin also functions as a timer W input port that is connected to the timer W regardless of the register setting of port 8. P84/FTIOD P83/FTIOC Port 8 P82/FTIOB P81/FTIOA P80/FTCI Figure 9.5 Port 8 Pin Configuration Port 8 has the following registers. * Port control register 8 (PCR8) * Port data register 8 (PDR8) Rev. 1.00, 11/03, page 123 of 376 9.5.1 Port Control Register 8 (PCR8) PCR8 selects inputs/outputs in bit units for pins to be used as general I/O ports of port 8. Bit 7 to 5 4 3 2 1 0 Bit Name PCR84 PCR83 PCR82 PCR81 PCR80 Initial Value 0 0 0 0 0 R/W W W W W W Description Reserved When each of the port 8 pins, P84 to P80, functions as an general I/O port, setting a PCR8 bit to 1 makes the corresponding pin an output port, while clearing the bit to 0 makes the pin an input port. 9.5.2 Port Data Register 8 (PDR8) PDR8 is a general I/O port data register of port 8. Bit 7 to 5 4 3 2 1 0 Bit Name P84 P83 P82 P81 P80 Initial Value All 0 0 0 0 0 0 R/W R/W R/W R/W R/W R/W Description Reserved These bits store output data for port 8 pins. If PDR8 is read while PCR8 bits are set to 1, the value stored in PDR8 is read. If PDR8 is read while PCR8 bits are cleared to 0, the pin states are read regardless of the value stored in PDR8. Rev. 1.00, 11/03, page 124 of 376 9.5.3 Pin Functions The correspondence between the register specification and the port functions is shown below. * P84/FTIOD pin Register Bit Name IOD2 Setting value 0 0 0 1 [Legend] X: Don't care 0 0 1 X TIOR1 IOD1 IOD0 0 1 X X PCR8 PCR84 0 1 X X 0 1 Pin Function P84 input/FTIOD input pin P84 output/FTIOD input pin FTIOD output pin FTIOD output pin P84 input/FTIOD input pin P84 output/FTIOD input pin * P83/FTIOC pin Register Bit Name IOC2 Setting value 0 0 0 1 [Legend] X: Don't care 0 0 1 X TIOR1 IOC1 IOC0 0 1 X X PCR8 PCR83 0 1 X X 0 1 Pin Function P83 input/FTIOC input pin P83 output/FTIOC input pin FTIOC output pin FTIOC output pin P83 input/FTIOC input pin P83 output/FTIOC input pin Rev. 1.00, 11/03, page 125 of 376 * P82/FTIOB pin Register Bit Name IOB2 Setting value 0 0 0 1 [Legend] X: Don't care 0 0 1 X TIOR0 IOB1 IOB0 0 1 X X PCR8 PCR82 0 1 X X 0 1 Pin Function P82 input/FTIOB input pin P82 output/FTIOB input pin FTIOB output pin FTIOB output pin P82 input/FTIOB input pin P82 output/FTIOB input pin * P81/FTIOA pin Register Bit Name IOA2 Setting value 0 0 0 1 [Legend] X: Don't care 0 0 1 X TIOR0 IOA1 IOA0 0 1 X X PCR8 PCR81 0 1 X X 0 1 Pin Function P81 input/FTIOA input pin P81 output/FTIOA input pin FTIOA output pin FTIOA output pin P81 input/FTIOA input pin P81 output/FTIOA input pin * P80/FTCI pin Register Bit Name PCR8 PCR80 1 Pin Function P80 input/FTCI input pin P80 output/FTCI input pin Setting value 0 Rev. 1.00, 11/03, page 126 of 376 9.6 Port B Port B is an input port also functioning as an A/D converter analog input pin and LVD external comparison voltage input pin. Each pin of the port B is shown in figure 9.6. PB3/AN3/ExtU Port B PB2/AN2/ExtD PB1/AN1 PB0/AN0 Figure 9.6 Port B Pin Configuration Port B has the following register. * Port data register B (PDRB) 9.6.1 Port Data Register B (PDRB) PDRB is a general input-only port data register of port B. Bit 7 to 4 3 2 1 0 Bit Name PB3 PB2 PB1 PB0 Initial Value R/W R R R R Description Reserved The input value of each pin is read by reading this register. However, if a port B pin is designated as an analog input channel by ADCSR in A/D converter or external comparison voltage input pin by LVDCR in low-voltage detection circuit, 0 is read. Rev. 1.00, 11/03, page 127 of 376 9.6.2 Pin Functions The correspondence between the register specification and the port functions is shown below. * PB3/AN3/ExtU pin Register Bit Name CH2 Setting value 0 1 ADCSR CH1 CH0 1 LVDCR VDDII 1 0 Other than the above values 1 0 Pin Function AN3 input pin AN3 input/ExtU input pin PB3 input pin PB3 input/ExtU input pin * PB2/AN2/ExtD pin Register Bit Name CH2 0 Setting value 0 0 1 ADCSR SCAN CH1 1 1 CH0 0 X LVDCR VDDII 1 0 1 0 [Legend] X: Don't care Pin Function AN2 input pin AN2 input/ExtD input pin PB2 input pin PB2 input/ExtD input pin Other than the above values * PB1/AN1 pin Register Bit Name CH2 0 [Legend] X: Don't care SCAN X 1 Setting value 0 ADCSR CH1 0 1 CH0 1 X PB1 input pin Pin Function AN1 input pin Other than the above values Rev. 1.00, 11/03, page 128 of 376 * PB0/AN0 pin Register Bit Name Setting value CH2 0 0 SCAN 0 1 ADCSR CH1 0 X CH0 0 X PB0 input pin Pin Function AN0 input pin Other than the above values [Legend] X: Don't care Rev. 1.00, 11/03, page 129 of 376 9.7 Port C Port C is a general I/O port also functioning as an external oscillation pin and clock output pin. Each pin of the port C is shown in figure 9.7. The register setting of CKCSR has priority for functions of the pins for both uses. Port C PC1/OSC2/CLKOUT PC0/OSC1 Figure 9.7 Port C Pin Configuration Port C has the following registers. * Port control register C (PCRC) * Port data register C (PDRC) Rev. 1.00, 11/03, page 130 of 376 9.7.1 Port Control Register C (PCRC) PCRC selects inputs/outputs in bit units for pins to be used as general I/O ports of port C. Bit 7 to 2 1 0 Bit Name PCRC1 PCRC0 Initial Value 0 0 R/W W W Description Reserved When each of the port C pins, PC1 and PC0, functions as an general I/O port, setting a PCRC bit to 1 makes the corresponding pin an output port, while clearing the bit to 0 makes the pin an input port. 9.7.2 Port Data Register C (PDRC) PDRC is a general I/O port data register of port C. Bit 7 to 2 1 0 Bit Name PC1 PC0 Initial Value 0 0 R/W R/W R/W Description Reserved These bits store output data for port C pins. If PDRC is read while PCRC bits are set to 1, the value stored in PDRC is read. If PDRC is read while PCRC bits are cleared to 0, the pin states are read regardless of the value stored in PDRC. 9.7.3 Pin Functions The correspondence between the register specification and the port functions is shown below. * PC1/OSC2/CLKOUT pin Register Bit Name Setting value PMRC1 0 1 [Legend] X: Don't care CKCSR PMRC0 X 0 1 PCRC PCRC1 0 1 X X Pin Function PC1 input pin PC1 output pin CLKOUT output pin OSC2 oscillation pin Rev. 1.00, 11/03, page 131 of 376 * PC0/OSC1 pin Register Bit Name CKCSR PMRC0 PCRC PCRC0 0 1 1 [Legend] X: Don't care X Pin Function PC0 input pin PC0 output pin OSC1 oscillation pin Setting value 0 Rev. 1.00, 11/03, page 132 of 376 Section 10 Timer B1 Timer B1 is an 8-bit timer that increments each time a clock pulse is input. This timer has two operating modes, interval and auto reload. Figure 10.1 shows a block diagram of timer B1. 10.1 Features * Selection of seven internal clock sources (/8192, /2048, /512, /256, /64, /16, and /4) * An interrupt is generated when the counter overflows. TMB1 PSS TCB1 TLB1 [Legend] TMB1: TCB1: TLB1: IRRTB1: PSS: Timer mode register B1 Timer counter B1 Timer load register B1 Timer B1 interrupt request flag Prescaler S IRRTB1 Figure 10.1 Block Diagram of Timer B1 TIM08B0A_000020020200 Rev. 1.00, 11/03, page 133 of 376 Internal data bus 10.2 Register Descriptions The timer B1 has the following registers. * Timer mode register B1 (TMB1) * Timer counter B1 (TCB1) * Timer load register B1 (TLB1) 10.2.1 Timer Mode Register B1 (TMB1) TMB1 selects the auto-reload function and input clock. Bit 7 Bit Name TMB17 Initial Value 0 R/W R/W Description Auto-Reload Function Select 0: Interval timer function selected 1: Auto-reload function selected 6 1 R/W Reserved Although this bit is readable/writable, it should not be set to 0. 5 to 3 2 1 0 TMB12 TMB11 TMB10 All 1 0 0 0 R/W R/W R/W Reserved These bits are always read as 1. Clock Select 000: Internal clock: /8192 001: Internal clock: /2048 010: Internal clock: /512 011: Internal clock: /256 100: Internal clock: /64 101: Internal clock: /16 110: Internal clock: /4 111: Reserved (setting prohibited) Rev. 1.00, 11/03, page 134 of 376 10.2.2 Timer Counter B1 (TCB1) TCB1 is an 8-bit read-only up-counter, which is incremented by internal clock input. The clock source for input to this counter is selected by bits TMB12 to TMB10 in TMB1. TCB1 values can be read by the CPU at any time. When TCB1 overflows from H'FF to H'00 or to the value set in TLB1, the IRRTB1 flag in IRR2 is set to 1. TCB1 is allocated to the same address as TLB1. 10.2.3 Timer Load Register B1 (TLB1) TLB1 is an 8-bit write-only register for setting the reload value of TCB1. When a reload value is set in TLB1, the same value is loaded into TCB1 as well, and TCB1 starts counting up from that value. When TCB1 overflows during operation in auto-reload mode, the TLB1 value is loaded into TCB1. Accordingly, overflow periods can be set within the range of 1 to 256 input clocks. TLB1 is allocated to the same address as TCB1. Rev. 1.00, 11/03, page 135 of 376 10.3 10.3.1 Operation Interval Timer Operation When bit TMB17 in TMB1 is cleared to 0, timer B1 functions as an 8-bit interval timer. Upon reset, TCB1 is cleared to H'00 and bit TMB17 is cleared to 0, so up-counting and interval timing resume immediately. The operating clock of timer B1 is selected from seven internal clock signals output by prescaler S. The selection is made by the TMB12 to TMB10 bits in TMB1. After the count value in TMB1 reaches H'FF, the next clock signal input causes timer B1 to overflow, setting flag IRRTB1 in IRR2 to 1. If IENTB1 in IENR2 is 1, an interrupt is requested to the CPU. At overflow, TCB1 returns to H'00 and starts counting up again. During interval timer operation (TMB17 = 0), when a value is set in TLB1, the same value is set in TCB1. 10.3.2 Auto-Reload Timer Operation Setting bit TMB17 in TMB1 to 1 causes timer B1 to function as an 8-bit auto-reload timer. When a reload value is set in TLB1, the same value is loaded into TCB1, becoming the value from which TCB1 starts its count. After the count value in TCB1 reaches H'FF, the next clock signal input causes timer B1 to overflow. The TLB1 value is then loaded into TCB1, and the count continues from that value. The overflow period can be set within a range from 1 to 256 input clocks, depending on the TLB1 value. The clock sources and interrupts in auto-reload mode are the same as in interval mode. In autoreload mode (TMB17 = 1), when a new value is set in TLB1, the TLB1 value is also loaded into TCB1. 10.4 Timer B1 Operating Modes Table 10.1 shows the timer B1 operating modes. Table 10.1 Timer B1 Operating Modes Operating Mode TCB1 TMB1 Interval Reset Reset Reset Active Functions Functions Functions Sleep Functions Functions Retained Subsleep Halted Halted Retained Standby Halted Halted Retained Auto-reload Reset Rev. 1.00, 11/03, page 136 of 376 Section 11 Timer V Timer V is an 8-bit timer based on an 8-bit counter. Timer V counts external events. Comparematch signals with two registers can also be used to reset the counter, request an interrupt, or output a pulse signal with an arbitrary duty cycle. Counting can be initiated by a trigger input at the TRGV pin, enabling pulse output control to be synchronized to the trigger, with an arbitrary delay from the trigger input. Figure 11.1 shows a block diagram of timer V. 11.1 Features * Choice of seven clock signals is available. Choice of six internal clock sources (/128, /64, /32, /16, /8, /4) or an external clock. * Counter can be cleared by compare match A or B, or by an external reset signal. If the count stop function is selected, the counter can be halted when cleared. * Timer output is controlled by two independent compare match signals, enabling pulse output with an arbitrary duty cycle, PWM output, and other applications. * Three interrupt sources: compare match A, compare match B, timer overflow * Counting can be initiated by trigger input at the TRGV pin. The rising edge, falling edge, or both edges of the TRGV input can be selected. TIM08V0A_000120030300 Rev. 1.00, 11/03, page 137 of 376 TCRV1 TCORB TRGV Trigger control Comparator Comparator PSS TCORA Clear control TMRIV TCRV0 Interrupt request control TMOV Output control TCSRV CMIA CMIB OVI [Legend] TCORA: TCORB: TCNTV: TCSRV: TCRV0: TCRV1: PSS: CMIA: CMIB: OVI: Time constant register A Time constant register B Timer counter V Timer control/status register V Timer control register V0 Timer control register V1 Prescaler S Compare-match interrupt A Compare-match interrupt B Overflow interrupt Figure 11.1 Block Diagram of Timer V 11.2 Input/Output Pins Table 11.1 shows the timer V pin configuration. Table 11.1 Pin Configuration Name Timer V output Timer V clock input Timer V reset input Trigger input Abbreviation I/O TMOV TMCIV TMRIV TRGV Output Input Input Input Function Timer V waveform output Clock input to TCNTV External input to reset TCNTV Trigger input to initiate counting Rev. 1.00, 11/03, page 138 of 376 Internal data bus TMCIV Clock select TCNTV 11.3 Register Descriptions Time V has the following registers. * Timer counter V (TCNTV) * Timer constant register A (TCORA) * Timer constant register B (TCORB) * Timer control register V0 (TCRV0) * Timer control/status register V (TCSRV) * Timer control register V1 (TCRV1) 11.3.1 Timer Counter V (TCNTV) TCNTV is an 8-bit up-counter. The clock source is selected by bits CKS2 to CKS0 in timer control register V0 (TCRV0). The TCNTV value can be read and written by the CPU at any time. TCNTV can be cleared by an external reset input signal, or by compare match A or B. The clearing signal is selected by bits CCLR1 and CCLR0 in TCRV0. When TCNTV overflows, OVF is set to 1 in timer control/status register V (TCSRV). TCNTV is initialized to H'00. 11.3.2 Time Constant Registers A and B (TCORA, TCORB) TCORA and TCORB have the same function. TCORA and TCORB are 8-bit read/write registers. TCORA and TCNTV are compared at all times. When the TCORA and TCNTV contents match, CMFA is set to 1 in TCSRV. If CMIEA is also set to 1 in TCRV0, a CPU interrupt is requested. Note that they must not be compared during the T3 state of a TCORA write cycle. Timer output from the TMOV pin can be controlled by the identifying signal (compare match A) and the settings of bits OS3 to OS0 in TCSRV. TCORA and TCORB are initialized to H'FF. Rev. 1.00, 11/03, page 139 of 376 11.3.3 Timer Control Register V0 (TCRV0) TCRV0 selects the input clock signals of TCNTV, specifies the clearing conditions of TCNTV, and controls each interrupt request. Bit 7 Bit Name CMIEB Initial Value 0 R/W R/W Description Compare Match Interrupt Enable B When this bit is set to 1, interrupt request from the CMFB bit in TCSRV is enabled. 6 CMIEA 0 R/W Compare Match Interrupt Enable A When this bit is set to 1, interrupt request from the CMFA bit in TCSRV is enabled. 5 OVIE 0 R/W Timer Overflow Interrupt Enable When this bit is set to 1, interrupt request from the OVF bit in TCSRV is enabled. 4 3 CCLR1 CCLR0 0 0 R/W R/W Counter Clear 1 and 0 These bits specify the clearing conditions of TCNTV. 00: Clearing is disabled 01: Cleared by compare match A 10: Cleared by compare match B 11: Cleared on the rising edge of the TMRIV pin. The operation of TCNTV after clearing depends on TRGE in TCRV1. 2 1 0 CKS2 CKS1 CKS0 0 0 0 R/W R/W R/W Clock Select 2 to 0 These bits select clock signals to input to TCNTV and the counting condition in combination with ICKS0 in TCRV1. Refer to table 11.2. Rev. 1.00, 11/03, page 140 of 376 Table 11.2 Clock Signals to Input to TCNTV and Counting Conditions TCRV0 Bit 2 CKS2 0 Bit 1 CKS1 0 Bit 0 CKS0 0 1 1 0 1 1 0 1 0 1 0 1 TCRV1 Bit 0 ICKS0 0 1 0 1 0 1 Description Clock input prohibited Internal clock: counts on /4, falling edge Internal clock: counts on /8, falling edge Internal clock: counts on /16, falling edge Internal clock: counts on /32, falling edge Internal clock: counts on /64, falling edge Internal clock: counts on /128, falling edge Clock input prohibited External clock: counts on rising edge External clock: counts on falling edge External clock: counts on rising and falling edge Rev. 1.00, 11/03, page 141 of 376 11.3.4 Timer Control/Status Register V (TCSRV) TCSRV indicates the status flag and controls outputs by using a compare match. Bit 7 Bit Name CMFB Initial Value 0 R/W R/W Description Compare Match Flag B [Setting condition] When the TCNTV value matches the TCORB value [Clearing condition] After reading CMFB = 1, cleared by writing 0 to CMFB 6 CMFA 0 R/W Compare Match Flag A [Setting condition] When the TCNTV value matches the TCORA value [Clearing condition] After reading CMFA = 1, cleared by writing 0 to CMFA 5 OVF 0 R/W Timer Overflow Flag [Setting condition] When TCNTV overflows from H'FF to H'00 [Clearing condition] After reading OVF = 1, cleared by writing 0 to OVF 4 3 2 OS3 OS2 1 0 0 R/W R/W Reserved This bit is always read as 1. Output Select 3 and 2 These bits select an output method for the TMOV pin by the compare match of TCORB and TCNTV. 00: No change 01: 0 output 10: 1 output 11: Output toggles 1 0 OS1 OS0 0 0 R/W R/W Output Select 1 and 0 These bits select an output method for the TMOV pin by the compare match of TCORA and TCNTV. 00: No change 01: 0 output 10: 1 output 11: Output toggles Rev. 1.00, 11/03, page 142 of 376 OS3 and OS2 select the output level for compare match B. OS1 and OS0 select the output level for compare match A. The two output levels can be controlled independently. After a reset, the timer output is 0 until the first compare match. 11.3.5 Timer Control Register V1 (TCRV1) TCRV1 selects the edge at the TRGV pin, enables TRGV input, and selects the clock input to TCNTV. Bit 7 to 5 4 3 Bit Name TVEG1 TVEG0 Initial Value All 1 0 0 R/W R/W R/W Description Reserved These bits are always read as 1. TRGV Input Edge Select These bits select the TRGV input edge. 00: TRGV trigger input is prohibited 01: Rising edge is selected 10: Falling edge is selected 11: Rising and falling edges are both selected 2 TRGE 0 R/W TCNT starts counting up by the input of the edge which is selected by TVEG1 and TVEG0. 0: Disables starting counting-up TCNTV by the input of the TRGV pin and halting counting-up TCNTV when TCNTV is cleared by a compare match. 1: Enables starting counting-up TCNTV by the input of the TRGV pin and halting counting-up TCNTV when TCNTV is cleared by a compare match. 1 0 ICKS0 1 0 R/W Reserved This bit is always read as 1. Internal Clock Select 0 This bit selects clock signals to input to TCNTV in combination with CKS2 to CKS0 in TCRV0. Refer to table 11.2. Rev. 1.00, 11/03, page 143 of 376 11.4 11.4.1 Operation Timer V Operation 1. According to table 11.2, six internal/external clock signals output by prescaler S can be selected as the timer V operating clock signals. When the operating clock signal is selected, TCNTV starts counting-up. Figure 11.2 shows the count timing with an internal clock signal selected, and figure 11.3 shows the count timing with both edges of an external clock signal selected. 2. When TCNTV overflows (changes from H'FF to H'00), the overflow flag (OVF) in TCRV0 will be set. The timing at this time is shown in figure 11.4. An interrupt request is sent to the CPU when OVIE in TCRV0 is 1. 3. TCNTV is constantly compared with TCORA and TCORB. Compare match flag A or B (CMFA or CMFB) is set to 1 when TCNTV matches TCORA or TCORB, respectively. The compare-match signal is generated in the last state in which the values match. Figure 11.5 shows the timing. An interrupt request is generated for the CPU when CMIEA or CMIEB in TCRV0 is 1. 4. When a compare match A or B is generated, the TMOV responds with the output value selected by bits OS3 to OS0 in TCSRV. Figure 11.6 shows the timing when the output is toggled by compare match A. 5. When CCLR1 or CCLR0 in TCRV0 is 01 or 10, TCNTV can be cleared by the corresponding compare match. Figure 11.7 shows the timing. 6. When CCLR1 or CCLR0 in TCRV0 is 11, TCNTV can be cleared by the rising edge of the input of TMRIV pin. A TMRIV input pulse-width of at least 1.5 system clocks is necessary. Figure 11.8 shows the timing. 7. When a counter-clearing source is generated with TRGE in TCRV1 set to 1, the counting-up is halted as soon as TCNTV is cleared. TCNTV resumes counting-up when the edge selected by TVEG1 or TVEG0 in TCRV1 is input from the TGRV pin. Internal clock TCNTV input clock TCNTV N-1 N N+1 Figure 11.2 Increment Timing with Internal Clock Rev. 1.00, 11/03, page 144 of 376 TMCIV (External clock input pin) TCNTV input clock TCNTV N-1 N N+1 Figure 11.3 Increment Timing with External Clock TCNTV H'FF H'00 Overflow signal OVF Figure 11.4 OVF Set Timing TCNTV N N+1 TCORA or TCORB Compare match signal CMFA or CMFB N Figure 11.5 CMFA and CMFB Set Timing Rev. 1.00, 11/03, page 145 of 376 Compare match A signal Timer V output pin Figure 11.6 TMOV Output Timing Compare match A signal TCNTV N H'00 Figure 11.7 Clear Timing by Compare Match Compare match A signal Timer V output pin TCNTV N-1 N H'00 Figure 11.8 Clear Timing by TMRIV Input Rev. 1.00, 11/03, page 146 of 376 11.5 11.5.1 Timer V Application Examples Pulse Output with Arbitrary Duty Cycle Figure 11.9 shows an example of output of pulses with an arbitrary duty cycle. 1. Set bits CCLR1 and CCLR0 in TCRV0 so that TCNTV will be cleared by compare match with TCORA. 2. Set bits OS3 to OS0 in TCSRV so that the output will go to 1 at compare match with TCORA and to 0 at compare match with TCORB. 3. Set bits CKS2 to CKS0 in TCRV0 and bit ICKS0 in TCRV1 to select the desired clock source. 4. With these settings, a waveform is output without further software intervention, with a period determined by TCORA and a pulse width determined by TCORB. TCNTV value H'FF Counter cleared TCORA TCORB H'00 TMOV Time Figure 11.9 Pulse Output Example Rev. 1.00, 11/03, page 147 of 376 11.5.2 Pulse Output with Arbitrary Pulse Width and Delay from TRGV Input The trigger function can be used to output a pulse with an arbitrary pulse width at an arbitrary delay from the TRGV input, as shown in figure 11.10. To set up this output: 1. Set bits CCLR1 and CCLR0 in TCRV0 so that TCNTV will be cleared by compare match with TCORB. 2. Set bits OS3 to OS0 in TCSRV so that the output will go to 1 at compare match with TCORA and to 0 at compare match with TCORB. 3. Set bits TVEG1 and TVEG0 in TCRV1 and set TRGE to select the falling edge of the TRGV input. 4. Set bits CKS2 to CKS0 in TCRV0 and bit ICKS0 in TCRV1 to select the desired clock source. 5. After these settings, a pulse waveform will be output without further software intervention, with a delay determined by TCORA from the TRGV input, and a pulse width determined by (TCORB to TCORA). TCNTV value H'FF Counter cleared TCORB TCORA H'00 TRGV Time TMOV Compare match A Compare match A Compare match B clears TCNTV and halts count-up Compare match B clears TCNTV and halts count-up Figure 11.10 Example of Pulse Output Synchronized to TRGV Input Rev. 1.00, 11/03, page 148 of 376 11.6 Usage Notes The following types of contention or operation can occur in timer V operation. 1. Writing to registers is performed in the T3 state of a TCNTV write cycle. If a TCNTV clear signal is generated in the T3 state of a TCNTV write cycle, as shown in figure 11.11, clearing takes precedence and the write to the counter is not carried out. If counting-up is generated in the T3 state of a TCNTV write cycle, writing takes precedence. If a compare match is generated in the T3 state of a TCORA or TCORB write cycle, the write to TCORA or TCORB takes precedence and the compare match signal is inhibited. Figure 11.12 shows the timing. If compare matches A and B occur simultaneously, any conflict between the output selections for compare match A and compare match B is resolved by the following priority: toggle output > output 1 > output 0. Depending on the timing, TCNTV may be incremented by a switch between different internal clock sources. When TCNTV is internally clocked, an increment pulse is generated from the falling edge of an internal clock signal, that is divided system clock (). Therefore, as shown in figure 11.13 the switch is from a high clock signal to a low clock signal, the switchover is seen as a falling edge, causing TCNTV to increment. TCNTV can also be incremented by a switch between internal and external clocks. TCNTV write cycle by CPU T1 T2 T3 2. 3. 4. Address TCNTV address Internal write signal Counter clear signal TCNTV N H'00 Figure 11.11 Contention between TCNTV Write and Clear Rev. 1.00, 11/03, page 149 of 376 TCORA write cycle by CPU T1 T2 T3 Address TCORA address Internal write signal TCNTV N N+1 TCORA N M TCORA write data Compare match signal Inhibited Figure 11.12 Contention between TCORA Write and Compare Match Clock before switching Clock after switching Count clock TCNTV N N+1 N+2 Write to CKS1 and CKS0 Figure 11.13 Internal Clock Switching and TCNTV Operation Rev. 1.00, 11/03, page 150 of 376 Section 12 Timer W The timer W has a 16-bit timer having output compare and input capture functions. The timer W can count external events and output pulses with an arbitrary duty cycle by compare match between the timer counter and four general registers. Thus, it can be applied to various systems. 12.1 Features * Selection of five counter clock sources: four internal clocks (, /2, /4, and /8) and an external clock (external events can be counted) * Capability to process up to four pulse outputs or four pulse inputs * Four general registers: Independently assignable output compare or input capture functions Usable as two pairs of registers; one register of each pair operates as a buffer for the output compare or input capture register * Four selectable operating modes: Waveform output by compare match Selections of 0 output, 1 output, or toggle output Input capture function Rising edge, falling edge, or both edges Counter clearing function Counters can be cleared by compare match PWM mode Up to three-phase PWM output can be provided with desired duty ratio. * Any initial timer output value can be set * Five interrupt sources Four compare match/input capture interrupts and an overflow interrupt. Table 12.1 summarizes the timer W functions, and figure 12.1 shows a block diagram of the timer W. TIM08W0A_000020020200 Rev. 1.00, 11/03, page 151 of 376 Table 12.1 Timer W Functions Input/Output Pins Item Count clock General registers (output compare/input capture registers) Counter clearing function Counter FTIOA FTIOB FTIOC FTIOD Internal clocks: , /2, /4, /8 External clock: FTCI Period GRA specified in GRA GRA compare match -- -- 0 1 Toggle Input capture function PWM mode Interrupt sources -- -- -- -- -- Overflow GRA compare match Yes Yes Yes Yes Yes Yes -- Compare match/input capture GRB GRC (buffer register for GRA in buffer mode) -- GRD (buffer register for GRB in buffer mode) -- -- Initial output value setting function Buffer function Compare match output Yes Yes Yes Yes Yes Yes Yes Compare match/input capture Yes -- Yes Yes Yes Yes Yes Compare match/input capture Yes -- Yes Yes Yes Yes Yes Compare match/input capture Rev. 1.00, 11/03, page 152 of 376 Internal clock: /2 /4 /8 External clock: FTCI Clock selector Control logic Comparator FTIOA FTIOB FTIOC FTIOD IRRTW TIERW TMRW TCRW TSRW TCNT TIOR GRC GRD GRA GRB [Legend] TMRW: TCRW: TIERW: TSRW: TIOR: TCNT: GRA: GRB: GRC: GRD: IRRTW: Timer mode register W (8 bits) Timer control register W (8 bits) Timer interrupt enable register W (8 bits) Timer status register W (8 bits) Timer I/O control register (8 bits) Timer counter (16 bits) General register A (input capture/output compare register: 16 bits) General register B (input capture/output compare register: 16 bits) General register C (input capture/output compare register: 16 bits) General register D (input capture/output compare register: 16 bits) Timer W interrupt request Figure 12.1 Timer W Block Diagram 12.2 Input/Output Pins Table 12.2 summarizes the timer W pins. Table 12.2 Pin Configuration Name External clock input Input capture/output compare A Input capture/output compare B Input capture/output compare C Input capture/output compare D Abbreviation FTCI FTIOA FTIOB Input/Output Input Input/output Input/output Function External clock input pin Output pin for GRA output compare or input pin for GRA input capture Output pin for GRB output compare, input pin for GRB input capture, or PWM output pin in PWM mode Output pin for GRC output compare, input pin for GRC input capture, or PWM output pin in PWM mode Output pin for GRD output compare, input pin for GRD input capture, or PWM output pin in PWM mode FTIOC Input/output FTIOD Input/output Rev. 1.00, 11/03, page 153 of 376 Bus interface Internal data bus 12.3 Register Descriptions The timer W has the following registers. * Timer mode register W (TMRW) * Timer control register W (TCRW) * Timer interrupt enable register W (TIERW) * Timer status register W (TSRW) * Timer I/O control register 0 (TIOR0) * Timer I/O control register 1 (TIOR1) * Timer counter (TCNT) * General register A (GRA) * General register B (GRB) * General register C (GRC) * General register D (GRD) Rev. 1.00, 11/03, page 154 of 376 12.3.1 Timer Mode Register W (TMRW) TMRW selects the general register functions and the timer output mode. Bit 7 Bit Name CTS Initial Value 0 R/W R/W Description Counter Start The counter operation is halted when this bit is 0, while it can be performed when this bit is 1. 6 5 BUFEB 1 0 R/W Reserved This bit is always read as 1. Buffer Operation B Selects the GRD function. 0: GRD operates as an input capture/output compare register 1: GRD operates as the buffer register for GRB 4 BUFEA 0 R/W Buffer Operation A Selects the GRC function. 0: GRC operates as an input capture/output compare register 1: GRC operates as the buffer register for GRA 3 2 PWMD 1 0 R/W Reserved This bit is always read as 1. PWM Mode D Selects the output mode of the FTIOD pin. 0: FTIOD operates normally (output compare output) 1: PWM output 1 PWMC 0 R/W PWM Mode C Selects the output mode of the FTIOC pin. 0: FTIOC operates normally (output compare output) 1: PWM output 0 PWMB 0 R/W PWM Mode B Selects the output mode of the FTIOB pin. 0: FTIOB operates normally (output compare output) 1: PWM output Rev. 1.00, 11/03, page 155 of 376 12.3.2 Timer Control Register W (TCRW) TCRW selects the timer counter clock source, selects a clearing condition, and specifies the timer output levels. Bit 7 Bit Name CCLR Initial Value 0 R/W R/W Description Counter Clear The TCNT value is cleared by compare match A when this bit is 1. When it is 0, TCNT operates as a freerunning counter. 6 5 4 CKS2 CKS1 CKS0 0 0 0 R/W R/W R/W Clock Select 2 to 0 Select the TCNT clock source. 000: Internal clock: counts on 001: Internal clock: counts on /2 010: Internal clock: counts on /4 011: Internal clock: counts on /8 1XX: Counts on rising edges of the external event (FTCI) When the internal clock source () is selected, subclock sources are counted in subactive and subsleep modes. 3 TOD 0 R/W Timer Output Level Setting D Sets the output value of the FTIOD pin until the first compare match D is generated. 0: Output value is 0* 1: Output value is 1* 2 TOC 0 R/W Timer Output Level Setting C Sets the output value of the FTIOC pin until the first compare match C is generated. 0: Output value is 0* 1: Output value is 1* 1 TOB 0 R/W Timer Output Level Setting B Sets the output value of the FTIOB pin until the first compare match B is generated. 0: Output value is 0* 1: Output value is 1* Rev. 1.00, 11/03, page 156 of 376 Bit 0 Bit Name TOA Initial Value 0 R/W R/W Description Timer Output Level Setting A Sets the output value of the FTIOA pin until the first compare match A is generated. 0: Output value is 0* 1: Output value is 1* [Legend] X: Don't care Note: * The change of the setting is immediately reflected in the output value. 12.3.3 Timer Interrupt Enable Register W (TIERW) TIERW controls the timer W interrupt request. Bit 7 Bit Name OVIE Initial Value 0 R/W R/W Description Timer Overflow Interrupt Enable When this bit is set to 1, FOVI interrupt requested by OVF flag in TSRW is enabled. 6 to 4 3 IMIED All 1 0 R/W Reserved These bits are always read as 1. Input Capture/Compare Match Interrupt Enable D When this bit is set to 1, IMID interrupt requested by IMFD flag in TSRW is enabled. 2 IMIEC 0 R/W Input Capture/Compare Match Interrupt Enable C When this bit is set to 1, IMIC interrupt requested by IMFC flag in TSRW is enabled. 1 IMIEB 0 R/W Input Capture/Compare Match Interrupt Enable B When this bit is set to 1, IMIB interrupt requested by IMFB flag in TSRW is enabled. 0 IMIEA 0 R/W Input Capture/Compare Match Interrupt Enable A When this bit is set to 1, IMIA interrupt requested by IMFA flag in TSRW is enabled. Rev. 1.00, 11/03, page 157 of 376 12.3.4 Timer Status Register W (TSRW) TSRW shows the status of interrupt requests. Bit 7 Bit Name OVF Initial Value 0 R/W R/W Description Timer Overflow Flag [Setting condition] * * 6 to 4 3 IMFD All 1 0 R/W When TCNT overflows from H'FFFF to H'0000 Read OVF when OVF = 1, then write 0 in OVF [Clearing condition] Reserved These bits are always read as 1. Input Capture/Compare Match Flag D [Setting conditions] * * TCNT = GRD when GRD functions as an output compare register The TCNT value is transferred to GRD by an input capture signal when GRD functions as an input capture register Read IMFD when IMFD = 1, then write 0 in IMFD [Clearing condition] * 2 IMFC 0 R/W Input Capture/Compare Match Flag C [Setting conditions] * * TCNT = GRC when GRC functions as an output compare register The TCNT value is transferred to GRC by an input capture signal when GRC functions as an input capture register Read IMFC when IMFC = 1, then write 0 in IMFC [Clearing condition] * Rev. 1.00, 11/03, page 158 of 376 Bit 1 Bit Name IMFB Initial Value 0 R/W R/W Description Input Capture/Compare Match Flag B [Setting conditions] * * TCNT = GRB when GRB functions as an output compare register The TCNT value is transferred to GRB by an input capture signal when GRB functions as an input capture register Read IMFB when IMFB = 1, then write 0 in IMFB [Clearing condition] * 0 IMFA 0 R/W Input Capture/Compare Match Flag A [Setting conditions] * * TCNT = GRA when GRA functions as an output compare register The TCNT value is transferred to GRA by an input capture signal when GRA functions as an input capture register Read IMFA when IMFA = 1, then write 0 in IMFA [Clearing condition] * Rev. 1.00, 11/03, page 159 of 376 12.3.5 Timer I/O Control Register 0 (TIOR0) TIOR0 selects the functions of GRA and GRB, and specifies the functions of the FTIOA and FTIOB pins. Bit 7 6 Bit Name IOB2 Initial Value 1 0 R/W R/W Description Reserved This bit is always read as 1. I/O Control B2 Selects the GRB function. 0: GRB functions as an output compare register 1: GRB functions as an input capture register 5 4 IOB1 IOB0 0 0 R/W R/W I/O Control B1 and B0 When IOB2 = 0, 00: No output at compare match 01: 0 output to the FTIOB pin at GRB compare match 10: 1 output to the FTIOB pin at GRB compare match 11: Output toggles to the FTIOB pin at GRB compare match When IOB2 = 1, 00: Input capture at rising edge at the FTIOB pin 01: Input capture at falling edge at the FTIOB pin 1X: Input capture at rising and falling edges of the FTIOB pin 3 2 IOA2 1 0 R/W Reserved This bit is always read as 1. I/O Control A2 Selects the GRA function. 0: GRA functions as an output compare register 1: GRA functions as an input capture register Rev. 1.00, 11/03, page 160 of 376 Bit 1 0 Bit Name IOA1 IOA0 Initial Value 0 0 R/W R/W R/W Description I/O Control A1 and A0 When IOA2 = 0, 00: No output at compare match 01: 0 output to the FTIOA pin at GRA compare match 10: 1 output to the FTIOA pin at GRA compare match 11: Output toggles to the FTIOA pin at GRA compare match When IOA2 = 1, 00: Input capture at rising edge of the FTIOA pin 01: Input capture at falling edge of the FTIOA pin 1X: Input capture at rising and falling edges of the FTIOA pin [Legend] X: Don't care 12.3.6 Timer I/O Control Register 1 (TIOR1) TIOR1 selects the functions of GRC and GRD, and specifies the functions of the FTIOC and FTIOD pins. Bit 7 6 Bit Name IOD2 Initial Value 1 0 R/W R/W Description Reserved This bit is always read as 1. I/O Control D2 Selects the GRD function. 0: GRD functions as an output compare register 1: GRD functions as an input capture register When GRB buffer operation has been selected by BUFEB in TMRW, select the same function as GRB. Rev. 1.00, 11/03, page 161 of 376 Bit 5 4 Bit Name IOD1 IOD0 Initial Value 0 0 R/W R/W R/W Description I/O Control D1 and D0 When IOD2 = 0, 00: No output at compare match 01: 0 output to the FTIOD pin at GRD compare match 10: 1 output to the FTIOD pin at GRD compare match 11: Output toggles to the FTIOD pin at GRD compare match When IOD2 = 1, 00: Input capture at rising edge at the FTIOD pin 01: Input capture at falling edge at the FTIOD pin 1X: Input capture at rising and falling edges at the FTIOD pin 3 2 IOC2 1 0 R/W Reserved This bit is always read as 1. I/O Control C2 Selects the GRC function. 0: GRC functions as an output compare register 1: GRC functions as an input capture register When GRA buffer operation has been selected by BUFEA in TMRW, select the same function as GRA. 1 0 IOC1 IOC0 0 0 R/W R/W I/O Control C1 and C0 When IOC2 = 0, 00: No output at compare match 01: 0 output to the FTIOC pin at GRC compare match 10: 1 output to the FTIOC pin at GRC compare match 11: Output toggles to the FTIOC pin at GRC compare match When IOC2 = 1, 00: Input capture to GRC at rising edge of the FTIOC pin 01: Input capture to GRC at falling edge of the FTIOC pin 1X: Input capture to GRC at rising and falling edges of the FTIOC pin [Legend] X: Don't care Rev. 1.00, 11/03, page 162 of 376 12.3.7 Timer Counter (TCNT) TCNT is a 16-bit readable/writable up-counter. The clock source is selected by bits CKS2 to CKS0 in TCRW. TCNT can be cleared to H'0000 through a compare match with GRA by setting the CCLR in TCRW to 1. When TCNT overflows (changes from H'FFFF to H'0000), the OVF flag in TSRW is set to 1. If OVIE in TIERW is set to 1 at this time, an interrupt request is generated. TCNT must always be read or written in 16-bit units; 8-bit access is not allowed. TCNT is initialized to H'0000 by a reset. 12.3.8 General Registers A to D (GRA to GRD) Each general register is a 16-bit readable/writable register that can function as either an outputcompare register or an input-capture register. The function is selected by settings in TIOR0 and TIOR1. When a general register is used as an input-compare register, its value is constantly compared with the TCNT value. When the two values match (a compare match), the corresponding flag (IMFA, IMFB, IMFC, or IMFD) in TSRW is set to 1. An interrupt request is generated at this time, when IMIEA, IMIEB, IMIEC, or IMIED is set to 1. Compare match output can be selected in TIOR. When a general register is used as an input-capture register, an external input-capture signal is detected and the current TCNT value is stored in the general register. The corresponding flag (IMFA, IMFB, IMFC, or IMFD) in TSRW is set to 1. If the corresponding interrupt-enable bit (IMIEA, IMIEB, IMIEC, or IMIED) in TSRW is set to 1 at this time, an interrupt request is generated. The edge of the input-capture signal is selected in TIOR. GRC and GRD can be used as buffer registers of GRA and GRB, respectively, by setting BUFEA and BUFEB in TMRW. For example, when GRA is set as an output-compare register and GRC is set as the buffer register for GRA, the value in the buffer register GRC is sent to GRA whenever compare match A is generated. When GRA is set as an input-capture register and GRC is set as the buffer register for GRA, the value in TCNT is transferred to GRA and the value in the buffer register GRC is transferred to GRA whenever an input capture is generated. GRA to GRD must be written or read in 16-bit units; 8-bit access is not allowed. GRA to GRD are initialized to H'FFFF by a reset. Rev. 1.00, 11/03, page 163 of 376 12.4 Operation The timer W has the following operating modes. * Normal Operation * PWM Operation 12.4.1 Normal Operation TCNT performs free-running or periodic counting operations. After a reset, TCNT is set as a freerunning counter. When the CTS bit in TMRW is set to 1, TCNT starts incrementing the count. When the count overflows from H'FFFF to H'0000, the OVF flag in TSRW is set to 1. If the OVIE in TIERW is set to 1, an interrupt request is generated. Figure 12.2 shows free-running counting. TCNT value H'FFFF H'0000 CTS bit Time Flag cleared by software OVF Figure 12.2 Free-Running Counter Operation Periodic counting operation can be performed when GRA is set as an output compare register and bit CCLR in TCRW is set to 1. When the count matches GRA, TCNT is cleared to H'0000, the IMFA flag in TSRW is set to 1. If the corresponding IMIEA bit in TIERW is set to 1, an interrupt request is generated. TCNT continues counting from H'0000. Figure 12.3 shows periodic counting. Rev. 1.00, 11/03, page 164 of 376 TCNT value GRA H'0000 CTS bit Flag cleared by software IMFA Time Figure 12.3 Periodic Counter Operation By setting a general register as an output compare register, compare match A, B, C, or D can cause the output at the FTIOA, FTIOB, FTIOC, or FTIOD pin to output 0, output 1, or toggle. Figure 12.4 shows an example of 0 and 1 output when TCNT operates as a free-running counter, 1 output is selected for compare match A, and 0 output is selected for compare match B. When signal is already at the selected output level, the signal level does not change at compare match. TCNT value H'FFFF GRA GRB H'0000 FTIOA FTIOB No change No change Time No change No change Figure 12.4 0 and 1 Output Example (TOA = 0, TOB = 1) Figure 12.5 shows an example of toggle output when TCNT operates as a free-running counter, and toggle output is selected for both compare match A and B. Rev. 1.00, 11/03, page 165 of 376 TCNT value H'FFFF GRA GRB H'0000 FTIOA FTIOB Time Toggle output Toggle output Figure 12.5 Toggle Output Example (TOA = 0, TOB = 1) Figure 12.6 shows another example of toggle output when TCNT operates as a periodic counter, cleared by compare match A. Toggle output is selected for both compare match A and B. TCNT value Counter cleared by compare match with GRA H'FFFF GRA GRB H'0000 FTIOA FTIOB Time Toggle output Toggle output Figure 12.6 Toggle Output Example (TOA = 0, TOB = 1) The TCNT value can be captured into a general register (GRA, GRB, GRC, or GRD) when a signal level changes at an input-capture pin (FTIOA, FTIOB, FTIOC, or FTIOD). Capture can take place on the rising edge, falling edge, or both edges. By using the input-capture function, the pulse width and periods can be measured. Figure 12.7 shows an example of input capture when both edges of FTIOA and the falling edge of FTIOB are selected as capture edges. TCNT operates as a free-running counter. Rev. 1.00, 11/03, page 166 of 376 TCNT value H'FFFF H'F000 H'AA55 H'55AA H'1000 H'0000 Time FTIOA GRA H'1000 H'F000 H'55AA FTIOB GRB H'AA55 Figure 12.7 Input Capture Operating Example Figure 12.8 shows an example of buffer operation when the GRA is set as an input-capture register and GRC is set as the buffer register for GRA. TCNT operates as a free-running counter, and FTIOA captures both rising and falling edge of the input signal. Due to the buffer operation, the GRA value is transferred to GRC by input-capture A and the TCNT value is stored in GRA. TCNT value H'FFFF H'DA91 H'5480 H'0245 H'0000 FTIOA Time GRA GRC H'0245 H'5480 H'0245 H'DA91 H'5480 Figure 12.8 Buffer Operation Example (Input Capture) Rev. 1.00, 11/03, page 167 of 376 12.4.2 PWM Operation In PWM mode, PWM waveforms are generated by using GRA as the period register and GRB, GRC, and GRD as duty registers. PWM waveforms are output from the FTIOB, FTIOC, and FTIOD pins. Up to three-phase PWM waveforms can be output. In PWM mode, a general register functions as an output compare register automatically. The output level of each pin depends on the corresponding timer output level set bit (TOB, TOC, and TOD) in TCRW. When TOB is 1, the FTIOB output goes to 1 at compare match A and to 0 at compare match B. When TOB is 0, the FTIOB output goes to 0 at compare match A and to 1 at compare match B. Thus the compare match output level settings in TIOR0 and TIOR1 are ignored for the output pin set to PWM mode. If the same value is set in the cycle register and the duty register, the output does not change when a compare match occurs. Figure 12.9 shows an example of operation in PWM mode. The output signals go to 1 and TCNT is cleared at compare match A, and the output signals go to 0 at compare match B, C, and D (TOB, TOC, and TOD = 1: initial output values are set to 1). TCNT value GRA GRB GRC GRD H'0000 FTIOB FTIOC Time Counter cleared by compare match A FTIOD Figure 12.9 PWM Mode Example (1) Figure 12.10 shows another example of operation in PWM mode. The output signals go to 0 and TCNT is cleared at compare match A, and the output signals go to 1 at compare match B, C, and D (TOB, TOC, and TOD = 0: initial output values are set to 1). Rev. 1.00, 11/03, page 168 of 376 TCNT value GRA GRB GRC Counter cleared by compare match A GRD H'0000 FTIOB FTIOC Time FTIOD Figure 12.10 PWM Mode Example (2) Figure 12.11 shows an example of buffer operation when the FTIOB pin is set to PWM mode and GRD is set as the buffer register for GRB. TCNT is cleared by compare match A, and FTIOB outputs 1 at compare match B and 0 at compare match A. Due to the buffer operation, the FTIOB output level changes and the value of buffer register GRD is transferred to GRB whenever compare match B occurs. This procedure is repeated every time compare match B occurs. TCNT value GRA H'0200 H'0450 H'0520 GRB H'0000 GRD Time H'0200 H'0450 H'0520 GRB H'0200 H'0450 H'0520 FTIOB Figure 12.11 Buffer Operation Example (Output Compare) Figures 12.12 and 12.13 show examples of the output of PWM waveforms with duty cycles of 0% and 100%. Rev. 1.00, 11/03, page 169 of 376 TCNT value GRA Write to GRB GRB H'0000 Duty 0% Write to GRB Time FTIOB TCNT value Write to GRB GRA Output does not change when cycle register and duty register compare matches occur simultaneously. Write to GRB Write to GRB GRB H'0000 Duty 100% Time FTIOB TCNT value Write to GRB GRA Output does not change when cycle register and duty register compare matches occur simultaneously. Write to GRB Write to GRB Time Duty 100% Duty 0% GRB H'0000 FTIOB Figure 12.12 PWM Mode Example (TOB, TOC, and TOD = 0: Initial Output Values are Set to 0) Rev. 1.00, 11/03, page 170 of 376 TCNT value GRA Write to GRB GRB H'0000 Duty 100% Write to GRB Time FTIOB TCNT value Write to GRB GRA Output does not change when cycle register and duty register compare matches occur simultaneously. Write to GRB Write to GRB GRB H'0000 Duty 0% Time FTIOB TCNT value Write to GRB GRA Output does not change when cycle register and duty register compare matches occur simultaneously. Write to GRB Write to GRB Time Duty 0% Duty 100% GRB H'0000 FTIOB Figure 12.13 PWM Mode Example (TOB, TOC, and TOD = 1: Initial Output Values are Set to 1) Rev. 1.00, 11/03, page 171 of 376 12.5 12.5.1 Operation Timing TCNT Count Timing Figure 12.14 shows the TCNT count timing when the internal clock source is selected. Figure 12.15 shows the timing when the external clock source is selected. The pulse width of the external clock signal must be at least two system clock () cycles; shorter pulses will not be counted correctly. Internal clock TCNT input clock TCNT N Rising edge N+1 N+2 Figure 12.14 Count Timing for Internal Clock Source External clock TCNT input clock TCNT Rising edge Rising edge N N+1 N+2 Figure 12.15 Count Timing for External Clock Source Rev. 1.00, 11/03, page 172 of 376 12.5.2 Output Compare Output Timing The compare match signal is generated in the last state in which TCNT and GR match (when TCNT changes from the matching value to the next value). When the compare match signal is generated, the output value selected in TIOR is output at the compare match output pin (FTIOA, FTIOB, FTIOC, or FTIOD). When TCNT matches GR, the compare match signal is generated only after the next counter clock pulse is input. Figure 12.16 shows the output compare timing. TCNT input clock TCNT N N+1 GRA to GRD Compare match signal FTIOA to FTIOD N Figure 12.16 Output Compare Output Timing Rev. 1.00, 11/03, page 173 of 376 12.5.3 Input Capture Timing Input capture on the rising edge, falling edge, or both edges can be selected through settings in TIOR0 and TIOR1. Figure 12.17 shows the timing when the falling edge is selected. The pulse width of the input capture signal must be at least two system clock () cycles; shorter pulses will not be detected correctly. Input capture input Input capture signal TCNT GRA to GRD N-1 N N+1 N+2 N Figure 12.17 Input Capture Input Signal Timing 12.5.4 Timing of Counter Clearing by Compare Match Figure 12.18 shows the timing when the counter is cleared by compare match A. When the GRA value is N, the counter counts from 0 to N, and its cycle is N + 1. Compare match signal TCNT N H'0000 GRA N Figure 12.18 Timing of Counter Clearing by Compare Match Rev. 1.00, 11/03, page 174 of 376 12.5.5 Buffer Operation Timing Figures 12.19 and 12.20 show the buffer operation timing. Compare match signal TCNT N N+1 GRC, GRD M GRA, GRB M Figure 12.19 Buffer Operation Timing (Compare Match) Input capture signal TCNT N N+1 GRA, GRB M N N+1 GRC, GRD M N Figure 12.20 Buffer Operation Timing (Input Capture) Rev. 1.00, 11/03, page 175 of 376 12.5.6 Timing of IMFA to IMFD Flag Setting at Compare Match If a general register (GRA, GRB, GRC, or GRD) is used as an output compare register, the corresponding IMFA, IMFB, IMFC, or IMFD flag is set to 1 when TCNT matches the general register. The compare match signal is generated in the last state in which the values match (when TCNT is updated from the matching count to the next count). Therefore, when TCNT matches a general register, the compare match signal is generated only after the next TCNT clock pulse is input. Figure 12.21 shows the timing of the IMFA to IMFD flag setting at compare match. TCNT input clock TCNT N N+1 GRA to GRD Compare match signal IMFA to IMFD IRRTW N Figure 12.21 Timing of IMFA to IMFD Flag Setting at Compare Match Rev. 1.00, 11/03, page 176 of 376 12.5.7 Timing of IMFA to IMFD Setting at Input Capture If a general register (GRA, GRB, GRC, or GRD) is used as an input capture register, the corresponding IMFA, IMFB, IMFC, or IMFD flag is set to 1 when an input capture occurs. Figure 12.22 shows the timing of the IMFA to IMFD flag setting at input capture. Input capture signal TCNT N GRA to GRD N IMFA to IMFD IRRTW Figure 12.22 Timing of IMFA to IMFD Flag Setting at Input Capture 12.5.8 Timing of Status Flag Clearing When the CPU reads a status flag while it is set to 1, then writes 0 in the status flag, the status flag is cleared. Figure 12.23 shows the status flag clearing timing. TSRW write cycle T1 T2 Address TSRW address Write signal IMFA to IMFD IRRTW Figure 12.23 Timing of Status Flag Clearing by CPU Rev. 1.00, 11/03, page 177 of 376 12.6 Usage Notes The following types of contention or operation can occur in timer W operation. 1. The pulse width of the input clock signal and the input capture signal must be at least two system clock () cycles; shorter pulses will not be detected correctly. 2. Writing to registers is performed in the T2 state of a TCNT write cycle. If counter clear signal occurs in the T2 state of a TCNT write cycle, clearing of the counter takes priority and the write is not performed, as shown in figure 12.24. If counting-up is generated in the TCNT write cycle to contend with the TCNT counting-up, writing takes precedence. 3. Depending on the timing, TCNT may be incremented by a switch between different internal clock sources. When TCNT is internally clocked, an increment pulse is generated from the rising edge of an internal clock signal, that is divided system clock (). Therefore, as shown in figure 12.25 the switch is from a low clock signal to a high clock signal, the switchover is seen as a rising edge, causing TCNT to increment. 4. If timer W enters module standby mode while an interrupt request is generated, the interrupt request cannot be cleared. Before entering module standby mode, disable interrupt requests. 5. The TOA to TOD bits in TCRW decide the value of the FTIO pin, which is output until the first compare match occurs. Once a compare match occurs and this compare match changes the values of FTIOA to FTIOD output, the values of the FTIOA to FTIOD pin output and the values read from the TOA to TOD bits may differ. Moreover, when the writing to TCRW and the generation of the compare match A to D occur at the same timing, the writing to TCRW has the priority. Thus, output change due to the compare match is not reflected to the FTIOA to FTIOD pins. Therefore, when bit manipulation instruction is used to write to TCRW, the values of the FTIOA to FTIOD pin output may result in an unexpected result. When TCRW is to be written to while compare match is operating, stop the counter once before accessing to TCRW, read the port 8 state to reflect the values of FTIOA to FTIOD output, to TOA to TOD, and then restart the counter. Figure 12.26 shows an example when the compare match and the bit manipulation instruction to TCRW occur at the same timing. Rev. 1.00, 11/03, page 178 of 376 TCNT write cycle T1 T2 Address TCNT address Write signal Counter clear signal TCNT N H'0000 Figure 12.24 Contention between TCNT Write and Clear Clock before switching Clock after switching Count clock TCNT N N+1 N+2 N+3 The change in signal level at clock switching is assumed to be a rising edge, and TCNT increments the count. Figure 12.25 Internal Clock Switching and TCNT Operation Rev. 1.00, 11/03, page 179 of 376 TCRW has been set to H'06. Compare match B and compare match C are used. The FTIOB pin is in the 1 output state, and is set to the toggle output or the 0 output by compare match B. When BCLR#2, @TCRW is executed to clear the TOC bit (the FTIOC signal is low) and compare match B occurs at the same timing as shown below, the H'02 writing to TCRW has priority and compare match B does not drive the FTIOB signal low; the FTIOB signal remains high. Bit TCRW Set value 7 CCLR 0 6 CKS2 0 5 CKS1 0 4 CKS0 0 3 TOD 0 2 TOC 1 1 TOB 1 0 TOA 0 BCLR#2, @TCRW (1) TCRW read operation: Read H'06 (2) Modify operation: Modify H'06 to H'02 (3) Write operation to TCRW: Write H'02 TCRW write signal Compare match signal B FTIOB pin Expected output Remains high because the 1 writing to TOB has priority Figure 12.26 When Compare Match and Bit Manipulation Instruction to TCRW Occur at the Same Timing Rev. 1.00, 11/03, page 180 of 376 Section 13 Watchdog Timer The watchdog timer is an 8-bit timer that can generate an internal reset signal for this LSI if a system crash prevents the CPU from writing to the timer counter, thus allowing it to overflow. The block diagram of the watchdog timer is shown in figure 13.1. WDT dedicated internal oscillator CLK TCSRWD PSS TCWD TMWD [Legend] TCSRWD: TCWD: PSS: TMWD: Timer control/status register WD Timer counter WD Prescaler S Timer mode register WD Internal reset signal Figure 13.1 Block Diagram of Watchdog Timer 13.1 Features * Selectable from nine counter input clocks. Eight clock sources (/64, /128, /256, /512, /1024, /2048, /4096, and /8192) or the WDT dedicated internal oscillator can be selected as the timer-counter clock. When the WDT dedicated internal oscillator is selected, it can operate as the watchdog timer in any operating mode. * Reset signal generated on counter overflow An overflow period of 1 to 256 times the selected clock can be set. * The watchdog timer is enabled in the initial state. It starts operating after the reset state is canceled. WDT0110A_000020030700 Rev. 1.00, 11/03, page 181 of 376 Internal data bus 13.2 Register Descriptions The watchdog timer has the following registers. * Timer control/status register WD (TCSRWD) * Timer counter WD (TCWD) * Timer mode register WD (TMWD) 13.2.1 Timer Control/Status Register WD (TCSRWD) TCSRWD performs the TCSRWD and TCWD write control. TCSRWD also controls the watchdog timer operation and indicates the operating state. TCSRWD must be rewritten by using the MOV instruction. The bit manipulation instruction cannot be used to change the setting value. Bit 7 Bit Name B6WI Initial Value 1 R/W R/W Description Bit 6 Write Inhibit The TCWE bit can be written only when the write value of the B6WI bit is 0. This bit is always read as 1. 6 TCWE 0 R/W Timer Counter WD Write Enable TCWD can be written when the TCWE bit is set to 1. When writing data to this bit, the value for bit 7 must be 0. 5 B4WI 1 R/W Bit 4 Write Inhibit The TCSRWE bit can be written only when the write value of the B4WI bit is 0. This bit is always read as 1. 4 TCSRWE 0 R/W Timer Control/Status Register W Write Enable The WDON and WRST bits can be written when the TCSRWE bit is set to 1. When writing data to this bit, the value for bit 5 must be 0. 3 B2WI 1 R/W Bit 2 Write Inhibit This bit can be written to the WDON bit only when the write value of the B2WI bit is 0. This bit is always read as 1. Rev. 1.00, 11/03, page 182 of 376 Bit 2 Bit Name WDON Initial Value 1 R/W R/W Description Watchdog Timer On TCWD starts counting up when the WDON bit is set to 1 and halts when the WDON bit is cleared to 0. The watchdog timer is enabled in the initial state. When the watchdog timer is not used, clear the WDON bit to 0. [Setting condition] * When 1 is written to the WDON bit and 0 is written to the B2WI bit while the TCSRWE bit = 1 Reset by the RES pin When 0 is written to the WDON bit and 0 is written to the B2WI bit while the TCSRWE bit = 1 [Clearing conditions] * * 1 B0WI 1 R/W Bit 0 Write Inhibit This bit can be written to the WRST bit only when the write value of the B0WI bit is 0. This bit is always read as 1. 0 WRST 0 R/W Watchdog Timer Reset [Setting condition] * When TCWD overflows and an internal reset signal is generated Reset by the RES pin When 0 is written to the WRST bit and 0 is written to the B0WI bit while the TCSRWE bit = 1 [Clearing conditions] * * Rev. 1.00, 11/03, page 183 of 376 13.2.2 Timer Counter WD (TCWD) TCWD is an 8-bit readable/writable up-counter. When TCWD overflows from H'FF to H'00, the internal reset signal is generated and the WRST bit in TCSRWD is set to 1. TCWD is initialized to H'00. 13.2.3 Timer Mode Register WD (TMWD) TMWD selects the input clock. Bit 7 to 4 3 2 1 0 Bit Name CKS3 CKS2 CKS1 CKS0 Initial Value All 1 1 1 1 1 R/W R/W R/W R/W R/W Description Reserved These bits are always read as 1. Clock Select 3 to 0 Select the clock to be input to TCWD. 1000: Internal clock: counts on /64 1001: Internal clock: counts on /128 1010: Internal clock: counts on /256 1011: Internal clock: counts on /512 1100: Internal clock: counts on /1024 1101: Internal clock: counts on /2048 1110: Internal clock: counts on /4096 1111: Internal clock: counts on 8192 0XXX: WDT dedicated internal oscillator For the overflow periods of the WDT dedicated internal oscillator, see section 20, Electrical Characteristics. [Legend] X: Don't care Rev. 1.00, 11/03, page 184 of 376 13.3 Operation The watchdog timer is provided with an 8-bit counter. After the reset state is released, TCWD starts counting up. When the TCWD count value overflows H'FF, an internal reset signal is generated. The internal reset signal is output for a period of 256 RC clock cycles. As TCWD is a writable counter, it starts counting from the value set in TCWD. An overflow period in the range of 1 to 256 input clock cycles can therefore be set, according to the TCWD set value. When the watchdog timer is not used, stop TCWD counting by writing 0 to B2WI and WDON simultaneously while the TCSRWE bit in TCSRWD is set to 1. (To stop the watchdog timer, two write accesses to TCSRWD are required.) Figure 13.2 shows an example of watchdog timer operation. Example: With 30ms overflow period when = 4 MHz 4 x 106 8192 x 30 x 10-3 = 14.6 Therefore, 256 - 15 = 241 (H'F1) is set in TCW. TCWD overflow H'FF H'F1 TCWD count value H'00 H'F1 written to TCWD Internal reset signal H'F1 written to TCWD Reset generated 256 RC clock cycles Figure 13.2 Watchdog Timer Operation Example Rev. 1.00, 11/03, page 185 of 376 Rev. 1.00, 11/03, page 186 of 376 Section 14 Serial Communication Interface 3 (SCI3) This LSI includes serial communication interface 3 (SCI3). SCI3 can handle both asynchronous and clocked synchronous serial communication. In asynchronous mode, serial data communication can be carried out using standard asynchronous communication chips such as a Universal Asynchronous Receiver/Transmitter (UART) or an Asynchronous Communication Interface Adapter (ACIA). A function is also provided for serial communication between processors (multiprocessor communication function). Figure 14.1 is a block diagram of SCI3. 14.1 Features * Choice of asynchronous or clocked synchronous serial communication mode * Full-duplex communication capability The transmitter and receiver are mutually independent, enabling transmission and reception to be executed simultaneously. Double-buffering is used in both the transmitter and the receiver, enabling continuous transmission and continuous reception of serial data. * On-chip baud rate generator allows any bit rate to be selected * External clock or on-chip baud rate generator can be selected as a transfer clock source. * Six interrupt sources Transmit-end, transmit-data-empty, receive-data-full, overrun error, framing error, and parity error. * Internal noise filter circuit (available for asynchronous serial communication only) Asynchronous mode * Data length: 7 or 8 bits * Stop bit length: 1 or 2 bits * Parity: Even, odd, or none * Receive error detection: Parity, overrun, and framing errors * Break detection: Break can be detected by reading the RXD pin level directly in the case of a framing error Clocked synchronous mode * Data length: 8 bits * Receive error detection: Overrun errors SCI0010A_000120030300 Rev. 1.00, 11/03, page 187 of 376 SCK3 External clock Baud rate generator BRC Internal clock ( /64, /16, /4, ) BRR Clock SMR Transmit/receive control circuit SCR3 SSR SPMR TXD TSR TDR RXD Noise filter circuit RSR RDR Interrupt request (TEI, TXI, RXI, ERI) [Legend] Receive shift register RSR: Receive data register RDR: Transmit shift register TSR: Transmit data register TDR: Serial mode register SMR: SCR3: Serial control register 3 Serial status register SSR: Bit rate register BRR: Bit rate counter BRC: SPMR: Sampling mode register Figure 14.1 Block Diagram of SCI3 Rev. 1.00, 11/03, page 188 of 376 Internal data bus 14.2 Input/Output Pins Table 14.1 shows the SCI3 pin configuration. Table 14.1 Pin Configuration Pin Name SCI3 clock SCI3 receive data input SCI3 transmit data output Abbreviation SCK3 RXD TXD I/O Input/output Input Output Function SCI3 clock input/output SCI3 receive data input SCI3 transmit data output 14.3 Register Descriptions SCI3 has the following registers for each channel. * Receive shift register (RSR) * Receive data register (RDR) * Transmit shift register (TSR) * Transmit data register (TDR) * Serial mode register (SMR) * Serial control register 3 (SCR3) * Serial status register (SSR) * Bit rate register (BRR) * Sampling mode register (SPMR) Rev. 1.00, 11/03, page 189 of 376 14.3.1 Receive Shift Register (RSR) RSR is a shift register that is used to receive serial data input from the RXD pin and convert it into parallel data. When one frame of data has been received, it is transferred to RDR automatically. RSR cannot be directly accessed by the CPU. 14.3.2 Receive Data Register (RDR) RDR is an 8-bit register that stores received data. When SCI3 has received one frame of serial data, it transfers the received serial data from RSR to RDR, where it is stored. After this, RSR is receive-enabled. As RSR and RDR function as a double buffer in this way, continuous receive operations are possible. After confirming that the RDRF bit in SSR is set to 1, read RDR only once. RDR cannot be written to by the CPU. RDR is initialized to H'00. 14.3.3 Transmit Shift Register (TSR) TSR is a shift register that transmits serial data. To perform serial data transmission, SCI3 first transfers transmit data from TDR to TSR automatically, then sends the data that starts from the LSB to the TXD pin. TSR cannot be directly accessed by the CPU. 14.3.4 Transmit Data Register (TDR) TDR is an 8-bit register that stores data for transmission. When SCI3 detects that TSR is empty, it transfers the transmit data written in TDR to TSR and starts transmission. The double-buffered structure of TDR and TSR enables continuous serial transmission. If the next transmit data has already been written to TDR during transmission of one-frame data, SCI3 transfers the written data to TSR to continue transmission. To achieve reliable serial transmission, write transmit data to TDR only once after confirming that the TDRE bit in SSR is set to 1. TDR is initialized to H'FF. Rev. 1.00, 11/03, page 190 of 376 14.3.5 Serial Mode Register (SMR) SMR is used to set the SCI3's serial transfer format and select the baud rate generator clock source. Bit 7 Bit Name COM Initial Value 0 R/W R/W Description Communication Mode 0: Asynchronous mode 1: Clocked synchronous mode 6 CHR 0 R/W Character Length (enabled only in asynchronous mode) 0: Selects 8 bits as the data length. 1: Selects 7 bits as the data length. 5 PE 0 R/W Parity Enable (enabled only in asynchronous mode) When this bit is set to 1, the parity bit is added to transmit data before transmission, and the parity bit is checked in reception. 4 PM 0 R/W Parity Mode (enabled only when the PE bit is 1 in asynchronous mode) 0: Selects even parity. 1: Selects odd parity. 3 STOP 0 R/W Stop Bit Length (enabled only in asynchronous mode) Selects the stop bit length in transmission. 0: 1 stop bit 1: 2 stop bits For reception, only the first stop bit is checked, regardless of the value in the bit. If the second stop bit is 0, it is treated as the start bit of the next transmit character. 2 MP 0 R/W Multiprocessor Mode When this bit is set to 1, the multiprocessor communication function is enabled. The PE bit and PM bit settings are invalid in multiprocessor mode. In clocked synchronous mode, clear this bit to 0. Rev. 1.00, 11/03, page 191 of 376 Bit 1 0 Bit Name CKS1 CKS0 Initial Value 0 0 R/W R/W R/W Description Clock Select 0 and 1 These bits select the clock source for the baud rate generator. 00: clock (n = 0) 01: /4 clock (n = 1) 10: /16 clock (n = 2) 11: /64 clock (n = 3) For the relationship between the bit rate register setting and the baud rate, see section 14.3.8, Bit Rate Register (BRR). n is the decimal representation of the value of n in BRR (see section 14.3.8, Bit Rate Register (BRR)). 14.3.6 Serial Control Register 3 (SCR3) SCR3 is a register that enables or disables SCI3 transfer operations and interrupt requests, and is also used to select the transfer clock source. For details on interrupt requests, refer to section 14.7, Interrupts. Bit 7 Bit Name TIE Initial Value 0 R/W R/W Description Transmit Interrupt Enable When this bit is set to 1, the TXI interrupt request is enabled. 6 RIE 0 R/W Receive Interrupt Enable When this bit is set to 1, RXI and ERI interrupt requests are enabled. 5 4 3 TE RE MPIE 0 0 0 R/W R/W R/W Transmit Enable When this bit s set to 1, transmission is enabled. Receive Enable When this bit is set to 1, reception is enabled. Multiprocessor Interrupt Enable (enabled only when the MP bit in SMR is 1 in asynchronous mode) When this bit is set to 1, receive data in which the multiprocessor bit is 0 is skipped, and setting of the RDRF, FER, and OER status flags in SSR is disabled. On receiving data in which the multiprocessor bit is 1, this bit is automatically cleared and normal reception is resumed. For details, refer to section 14.6, Multiprocessor Communication Function. Rev. 1.00, 11/03, page 192 of 376 Bit 2 1 0 Bit Name TEIE CKE1 CKE0 Initial Value 0 0 0 R/W R/W R/W R/W Description Transmit End Interrupt Enable When this bit is set to 1, TEI interrupt request is enabled. Clock Enable 0 and 1 Selects the clock source. * Asynchronous mode 00: On-chip baud rate generator 01: On-chip baud rate generator Outputs a clock of the same frequency as the bit rate from the SCK3 pin. 10: External clock Inputs a clock with a frequency 16 times the bit rate from the SCK3 pin. 11:Reserved * Clocked synchronous mode 00: On-chip clock (SCK3 pin functions as clock output) 01:Reserved 10: External clock (SCK3 pin functions as clock input) 11:Reserved Rev. 1.00, 11/03, page 193 of 376 14.3.7 Serial Status Register (SSR) SSR is a register containing status flags of SCI3 and multiprocessor bits for transfer. 1 cannot be written to flags TDRE, RDRF, OER, PER, and FER; they can only be cleared. Bit 7 Bit Name TDRE Initial Value 1 R/W R/W Description Transmit Data Register Empty Indicates whether TDR contains transmit data. [Setting conditions] * * * * 6 RDRF 0 R/W When the TE bit in SCR3 is 0 When data is transferred from TDR to TSR When 0 is written to TDRE after reading TDRE = 1 When the transmit data is written to TDR [Clearing conditions] Receive Data Register Full Indicates that the received data is stored in RDR. [Setting condition] * When serial reception ends normally and receive data is transferred from RSR to RDR When 0 is written to RDRF after reading RDRF = 1 When data is read from RDR [Clearing conditions] * * 5 OER 0 R/W Overrun Error [Setting condition] * * When an overrun error occurs in reception When 0 is written to OER after reading OER = 1 [Clearing condition] 4 FER 0 R/W Framing Error [Setting condition] * * When a framing error occurs in reception When 0 is written to FER after reading FER = 1 [Clearing condition] Rev. 1.00, 11/03, page 194 of 376 Bit 3 Bit Name PER Initial Value 0 R/W R/W Description Parity Error [Setting condition] * * When a parity error is detected during reception When 0 is written to PER after reading PER = 1 [Clearing condition] 2 TEND 1 R Transmit End [Setting conditions] * * When the TE bit in SCR3 is 0 When TDRE = 1 at transmission of the last bit of a 1frame serial transmit character When 0 is written to TDRE after reading TDRE = 1 When the transmit data is written to TDR [Clearing conditions] * * 1 MPBR 0 R Multiprocessor Bit Receive MPBR stores the multiprocessor bit in the receive character data. When the RE bit in SCR3 is cleared to 0, its state is retained. 0 MPBT 0 R/W Multiprocessor Bit Transfer MPBT stores the multiprocessor bit to be added to the transmit character data. Rev. 1.00, 11/03, page 195 of 376 14.3.8 Bit Rate Register (BRR) BRR is an 8-bit register that adjusts the bit rate. The initial value of BRR is H'FF. Table 14.2 shows the relationship between the N setting in BRR and the n setting in bits CKS1 and CKS0 of SMR in asynchronous mode. Table 14.3 shows the maximum bit rate for each frequency in asynchronous mode. The values shown in both tables 14.2 and 14.3 are values in active (highspeed) mode. Table 14.4 shows the relationship between the N setting in BRR and the n setting in bits CKS1 and CKS0 of SMR in clocked synchronous mode. The values shown in table 14.5 are values in active (high-speed) mode. The N setting in BRR and error for other operating frequencies and bit rates can be obtained by the following formulas: [Asynchronous Mode] N= x 106 - 1 64 x 22n-1 x B Error (%) = x 106 - 1 x 100 (N + 1) x B x 64 x 22n-1 [Clocked Synchronous Mode] N= x 106 - 1 8 x 22n-1 x B Legend B: Bit rate (bit/s) N: BRR setting for baud rate generator (0 N 255) : Operating frequency (MHz) n: CSK1 and CSK0 settings in SMR (0 n 3) Rev. 1.00, 11/03, page 196 of 376 Table 14.2 Examples of BRR Settings for Various Bit Rates (Asynchronous Mode) Operating Frequency (MHz) 2 Bit Rate (bits/s) 110 150 300 600 1200 2400 4800 9600 19200 31250 38400 n 1 1 0 0 0 0 0 0 0 0 0 N 141 103 207 103 51 25 12 6 2 1 1 Error (%) 0.03 0.16 0.16 0.16 0.16 0.16 0.16 -6.99 8.51 0.00 -18.62 n 1 1 0 0 0 0 0 0 0 0 0 2.097152 N 148 108 217 108 54 26 13 6 2 1 1 Error (%) -0.04 0.21 0.21 0.21 -0.70 1.14 -2.48 -2.48 13.78 4.86 -14.67 n 1 1 0 0 0 0 0 0 0 0 0 2.4576 N 174 127 255 127 63 31 15 7 3 1 1 Error (%) -0.26 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 22.88 0.00 n 1 1 1 0 0 0 0 0 0 0 -- N 212 155 77 155 77 38 19 9 4 2 -- 3 Error (%) 0.03 0.16 0.16 0.16 0.16 0.16 -2.34 -2.34 -2.34 0.00 -- Operating Frequency (MHz) 3.6864 Bit Rate (bits/s) 110 150 300 600 1200 2400 4800 9600 19200 31250 38400 n 2 1 1 0 0 0 0 0 0 -- 0 N 64 191 95 191 95 47 23 11 5 -- 2 Error (%) 0.70 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 -- 0.00 n 2 1 1 0 0 0 0 0 0 0 0 N 70 207 103 207 103 51 25 12 6 3 2 4 Error (%) 0.03 0.16 0.16 0.16 0.16 0.16 0.16 0.16 -6.99 0.00 8.51 n 2 1 1 0 0 0 0 0 0 0 0 4.9152 N 86 255 127 255 127 63 31 15 7 4 3 Error (%) 0.31 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 -1.70 0.00 n 2 2 1 1 0 0 0 0 0 0 0 N 88 64 129 64 129 64 32 15 7 4 3 5 Error (%) -0.25 0.16 0.16 0.16 0.16 0.16 -1.36 1.73 1.73 0.00 1.73 [Legend] : A setting is available but error occurs Rev. 1.00, 11/03, page 197 of 376 Operating Frequency (MHz) 6 Bit Rate (bit/s) 110 150 300 600 1200 2400 4800 9600 19200 31250 38400 n 2 2 1 1 0 0 0 0 0 0 0 N 106 77 155 77 155 77 38 19 9 5 4 Error (%) -0.44 0.16 0.16 0.16 0.16 0.16 0.16 -2.34 -2.34 0.00 -2.34 n 2 2 1 1 0 0 0 0 0 0 0 6.144 N 108 79 159 79 159 79 39 19 9 5 4 Error (%) 0.08 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 2.40 0.00 n 2 2 1 1 0 0 0 0 0 0 0 7.3728 N 130 95 191 95 191 95 47 23 11 6 5 Error (%) -0.07 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 5.33 0.00 Rev. 1.00, 11/03, page 198 of 376 Operating Frequency (MHz) Bit Rate (bit/s) 110 150 300 600 1200 2400 4800 9600 19200 31250 38400 8 n 2 2 1 1 0 0 0 0 0 0 0 N 141 103 207 103 207 103 51 25 12 7 6 Error (%) 0.03 0.16 0.16 0.16 0.16 0.16 0.16 0.16 0.16 0.00 -6.99 n 2 2 1 1 0 0 0 0 0 0 0 9.8304 N 174 127 255 127 255 127 63 31 15 9 7 Error (%) -0.26 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 -1.70 0.00 n 2 2 2 1 1 0 0 0 0 0 0 N 177 129 64 129 64 129 64 32 15 9 7 10 Error (%) -0.25 0.16 0.16 0.16 0.16 0.16 0.16 -1.36 1.73 0.00 1.73 Table 14.3 Maximum Bit Rate for Each Frequency (Asynchronous Mode) (MHz) 2 2.4576 3 3.6864 4 4.9152 Maximum Bit Rate (bit/s) 62500 76800 93750 115200 125000 153600 n 0 0 0 0 0 0 0 N 0 0 0 0 0 0 0 (MHz) 5 6 6.144 7.3728 8 9.8304 10 Maximum Bit Rate (bit/s) 156250 187500 192000 230400 250000 307200 312500 n 0 0 0 0 0 0 0 N 0 0 0 0 0 0 0 2.097152 65536 Rev. 1.00, 11/03, page 199 of 376 Table 14.4 Examples of BRR Settings for Various Bit Rates (Clocked Synchronous Mode) Operating Frequency (MHz) 2 Bit Rate (bit/s) 110 250 500 1k 2.5k 5k 10k 25k 50k 100k 250k 500k 1M 2M 2.5M 4M [Legend] Blank: No setting is available. --: A setting is available but error occurs. *: Continuous transfer is not possible. n 3 2 1 1 0 0 0 0 0 0 0 0 N 70 124 249 124 199 99 49 19 9 4 1 0* n -- 2 2 1 1 0 0 0 0 0 0 0 0 4 N -- 249 124 249 99 199 99 39 19 9 3 1 0* n -- 3 2 2 1 1 0 0 0 0 0 0 0 0 8 N -- 124 249 124 199 99 199 79 39 19 7 3 1 0* n -- -- -- -- 1 1 0 0 0 0 0 0 -- -- 0 10 N -- -- -- -- 249 124 249 99 49 24 9 4 -- -- 0* Rev. 1.00, 11/03, page 200 of 376 14.3.9 Sampling Mode Register (SPMR) SPMR controls the serial communication function. Bit 7 to 3 2 Bit Name STDSPM Initial Value All 1 1 R/W R/W Description Reserved These bits are always read as 1. Noise Filter Function Select Selects the noise filter function for the RXD pin in asynchronous mode. 0: Noise filter circuit is enabled 1: Noise filter circuit is disabled 1, 0 All 1 Reserved These bits are always read as 1. * Noise Filter Circuit The RXD input signal is latched through the noise filter circuit. The noise filter circuit comprises a series of three latch circuits and a match detection circuit. The RXD input signal is sampled by the basic clock with the 16 times the transfer clock frequency. If three latch outputs match, its level is transferred to the next stage. If not, the circuit holds the previous value. That is, when the incoming signal holds the same level for three clock cycles, it is regarded as the proper signal. If the levels of the signal is less than three clock cycles, the signal is regarded as a noise. Sampling clock C C Q D Q D C Q RXD input signal D Latch Latch Latch Match detection circuit SPMR (STDSPM) Internal RXD signal shown in figure 14.1 Internal basic clock cycle Sampling clock Figure 14.2 Block Diagram of Noise Filter Circuit Rev. 1.00, 11/03, page 201 of 376 14.4 Operation in Asynchronous Mode Figure 14.3 shows the general format for asynchronous serial communication. One character (or frame) consists of a start bit (low level), followed by data (in LSB-first order), a parity bit (high or low level), and finally stop bits (high level). Inside the SCI3, the transmitter and receiver are independent units, enabling full-duplex. Both the transmitter and the receiver also have a doublebuffered structure, so data can be read or written during transmission or reception, enabling continuous data transfer. LSB Serial Start data bit Transmit/receive data MSB Parity bit Stop bit 1 Mark state 1 bit 7 or 8 bits 1 bit, or none 1 or 2 bits One unit of transfer data (character or frame) Figure 14.3 Data Format in Asynchronous Communication 14.4.1 Clock Either an internal clock generated by the on-chip baud rate generator or an external clock input at the SCK3 pin can be selected as the SCI3's serial clock, according to the setting of the COM bit in SMR and the CKE0 and CKE1 bits in SCR3. When an external clock is input at the SCK3 pin, the clock frequency should be 16 times the bit rate used. When SCI3 is operated on an internal clock, the clock can be output from the SCK3 pin. The frequency of the clock output in this case is equal to the bit rate, and the phase is such that the rising edge of the clock is in the middle of the transmit data, as shown in figure 14.4. Clock Serial data 0 D0 D1 D2 D3 D4 D5 D6 D7 0/1 1 1 1 character (frame) Figure 14.4 Relationship between Output Clock and Transfer Data Phase (Asynchronous Mode)(Example with 8-Bit Data, Parity, Two Stop Bits) Rev. 1.00, 11/03, page 202 of 376 14.4.2 SCI3 Initialization Before transmitting and receiving data, you should first clear the TE and RE bits in SCR3 to 0, then initialize SCI3 as described below. When the operating mode, or transfer format, is changed for example, the TE and RE bits must be cleared to 0 before making the change using the following procedure. When the TE bit is cleared to 0, the TDRE flag is set to 1. Note that clearing the RE bit to 0 does not initialize the contents of the RDRF, PER, FER, and OER flags, or the contents of RDR. When the external clock is used in asynchronous mode, the clock must be supplied even during initialization. [1] Start initialization Set the clock selection in SCR3. Be sure to clear bits RIE, TIE, TEIE, and MPIE, and bits TE and RE, to 0. When the clock output is selected in asynchronous mode, clock is output immediately after CKE1 and CKE0 settings are made. When the clock output is selected at reception in clocked synchronous mode, clock is output immediately after CKE1, CKE0, and RE are set to 1. [2] [3] No 1-bit interval elapsed? Yes Set TE and RE bits in SCR3 to 1, and set RIE, TIE, TEIE, and MPIE bits. For transmit (TE=1), also set the TxD bit in PMR1. [4] Set the data transfer format in SMR. Write a value corresponding to the bit rate to BRR. Not necessary if an external clock is used. Wait at least one bit interval, then set the TE bit or RE bit in SCR3 to 1. RE settings enable the RXD pin to be used. For transmission, set the TXD bit in PMR1 to 1 to enable the TXD output pin to be used. Also set the RIE, TIE, TEIE, and MPIE bits, depending on whether interrupts are required. In asynchronous mode, the bits are marked at transmission and idled at reception to wait for the start bit. For transmission, set the TE bit to 1 and then output 1 for one frame to enable. Clear TE and RE bits in SCR3 to 0 [1] Set CKE1 and CKE0 bits in SCR3 Set data transfer format in SMR [2] Set value in BRR Wait [3] [4] Figure 14.5 Sample SCI3 Initialization Flowchart Rev. 1.00, 11/03, page 203 of 376 14.4.3 Data Transmission Figure 14.6 shows an example of operation for transmission in asynchronous mode. In transmission, SCI3 operates as described below. 1. SCI3 monitors the TDRE flag in SSR. If the flag is cleared to 0, SCI3 recognizes that data has been written to TDR, and transfers the data from TDR to TSR. 2. After transferring data from TDR to TSR, SCI3 sets the TDRE flag to 1 and starts transmission. If the TIE bit is set to 1 at this time, a TXI interrupt request is generated. Continuous transmission is possible because the TXI interrupt routine writes next transmit data to TDR before transmission of the current transmit data has been completed. 3. SCI3 checks the TDRE flag at the timing for sending the stop bit. 4. If the TDRE flag is 0, the data is transferred from TDR to TSR, the stop bit is sent, and then serial transmission of the next frame is started. 5. If the TDRE flag is 1, the TEND flag in SSR is set to 1, the stop bit is sent, and then the "mark state" is entered, in which 1 is output. If the TEIE bit in SCR3 is set to 1 at this time, a TEI interrupt request is generated. 6. Figure 14.7 shows a sample flowchart for transmission in asynchronous mode. Start bit Serial data 1 0 D0 D1 1 frame Transmit data D7 Parity Stop Start bit bit bit 0/1 1 0 D0 Transmit data D1 1 frame D7 Parity Stop bit bit 0/1 1 Mark state 1 TDRE TEND LSI TXI interrupt operation request generated User processing TDRE flag cleared to 0 Data written to TDR TXI interrupt request generated TEI interrupt request generated Figure 14.6 Example of SCI3 Transmission in Asynchronous Mode (8-Bit Data, Parity, One Stop Bit) Rev. 1.00, 11/03, page 204 of 376 Start transmission [1] Read TDRE flag in SSR No TDRE = 1 Yes Write transmit data to TDR [2] Yes All data transmitted? No [1] Read SSR and check that the TDRE flag is set to 1, then write transmit data to TDR. When data is written to TDR, the TDRE flag is automaticaly cleared to 0. [2] To continue serial transmission, read 1 from the TDRE flag to confirm that writing is possible, then write data to TDR. When data is written to TDR, the TDRE flag is automaticaly cleared to 0. [3] To output a break in serial transmission, after setting PCR to 1 and PDR to 0, clear TxD in PMR1 to 0, then clear the TE bit in SCR3 to 0. Read TEND flag in SSR No TEND = 1 Yes No Break output? Yes Clear PDR to 0 and set PCR to 1 [3] Clear TE bit in SCR3 to 0 Figure 14.7 Sample Serial Transmission Data Flowchart (Asynchronous Mode) Rev. 1.00, 11/03, page 205 of 376 14.4.4 Serial Data Reception Figure 14.8 shows an example of operation for reception in asynchronous mode. In serial reception, SCI3 operates as described below. 1. SCI3 monitors the communication line. If a start bit is detected, SCI3 performs internal synchronization, receives receive data in RSR, and checks the parity bit and stop bit. 2. If an overrun error occurs (when reception of the next data is completed while the RDRF flag is still set to 1), the OER bit in SSR is set to 1. If the RIE bit in SCR3 is set to 1 at this time, an ERI interrupt request is generated. Receive data is not transferred to RDR. 3. If a parity error is detected, the PER bit in SSR is set to 1 and receive data is transferred to RDR. If the RIE bit in SCR3 is set to 1 at this time, an ERI interrupt request is generated. 4. If a framing error is detected (when the stop bit is 0), the FER bit in SSR is set to 1 and receive data is transferred to RDR. If the RIE bit in SCR3 is set to 1 at this time, an ERI interrupt request is generated. 5. If reception is completed successfully, the RDRF bit in SSR is set to 1, and receive data is transferred to RDR. If the RIE bit in SCR3 is set to 1 at this time, an RXI interrupt request is generated. Continuous reception is possible because the RXI interrupt routine reads the receive data transferred to RDR before reception of the next receive data has been completed. Start bit Serial data 1 0 D0 D1 1 frame Receive data D7 Parity Stop Start bit bit bit 0/1 1 0 D0 Receive data D1 1 frame D7 Parity Stop bit bit 0/1 0 Mark state (idle state) 1 RDRF FER LSI operation User processing RXI request RDRF cleared to 0 RDR data read 0 stop bit detected ERI request in response to framing error Framing error processing Figure 14.8 Example of SCI3 Reception in Asynchronous Mode (8-Bit Data, Parity, One Stop Bit) Table 14.5 shows the states of the SSR status flags and receive data handling when a receive error is detected. If a receive error is detected, the RDRF flag retains its state before receiving data. Reception cannot be resumed while a receive error flag is set to 1. Accordingly, clear the OER, FER, PER, and RDRF bits to 0 before resuming reception. Figure 14.9 shows a sample flow chart for serial data reception. Rev. 1.00, 11/03, page 206 of 376 Table 14.5 SSR Status Flags and Receive Data Handling SSR Status Flag RDRF* 1 0 0 1 1 0 1 Note: * OER 1 0 0 1 1 0 1 FER 0 1 0 1 0 1 1 PER 0 0 1 0 1 1 1 Receive Data Lost Transferred to RDR Transferred to RDR Lost Lost Transferred to RDR Lost Receive Error Type Overrun error Framing error Parity error Overrun error + framing error Overrun error + parity error Framing error + parity error Overrun error + framing error + parity error The RDRF flag retains the state it had before data reception. Start reception Read OER, PER, and FER flags in SSR [1] Yes OER+PER+FER = 1 [4] No Error processing (Continued on next page) Read RDRF flag in SSR No RDRF = 1 Yes [2] Read receive data in RDR [1] Read the OER, PER, and FER flags in SSR to identify the error. If a receive error occurs, performs the appropriate error processing. [2] Read SSR and check that RDRF = 1, then read the receive data in RDR. The RDRF flag is cleared automatically. [3] To continue serial reception, before the stop bit for the current frame is received, read the RDRF flag and read RDR. The RDRF flag is cleared automatically. [4] If a receive error occurs, read the OER, PER, and FER flags in SSR to identify the error. After performing the appropriate error processing, ensure that the OER, PER, and FER flags are all cleared to 0. Reception cannot be resumed if any of these flags are set to 1. In the case of a framing error, a break can be detected by reading the value of the input port corresponding to the RxD pin. Yes All data received? (A) No Clear RE bit in SCR3 to 0 Figure 14.9 Sample Serial Reception Data Flowchart (Asynchronous Mode) Rev. 1.00, 11/03, page 207 of 376 14.5 Operation in Clocked Synchronous Mode Figure 14.10 shows the general format for clocked synchronous communication. In clocked synchronous mode, data is transmitted or received synchronous with clock pulses. A single character in the transmit data consists of the 8-bit data starting from the LSB. In clocked synchronous serial communication, data on the transmission line is output from one falling edge of the synchronization clock to the next. In clocked synchronous mode, SCI3 receives data in synchronous with the rising edge of the synchronization clock. After 8-bit data is output, the transmission line holds the MSB state. In clocked synchronous mode, no parity or multiprocessor bit is added. Inside the SCI3, the transmitter and receiver are independent units, enabling fullduplex communication through the use of a common clock. Both the transmitter and the receiver also have a double-buffered structure, so data can be read or written during transmission or reception, enabling continuous data transfer. 8-bit * Synchronization clock LSB Serial data Don't care Note: * High except in continuous transfer Bit 0 Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 MSB Bit 7 Don't care One unit of transfer data (character or frame) * Figure 14.10 Data Format in Clocked Synchronous Communication 14.5.1 Clock Either an internal clock generated by the on-chip baud rate generator or an external synchronization clock input at the SCK3 pin can be selected, according to the setting of the COM bit in SMR and CKE0 and CKE1 bits in SCR3. When SCI3 is operated on an internal clock, the synchronization clock is output from the SCK3 pin. Eight synchronization clock pulses are output in the transfer of one character, and when no transfer is performed the clock is fixed high. 14.5.2 SCI3 Initialization Before transmitting and receiving data, SCI3 should be initialized as described in a sample flowchart in figure 14.5. Rev. 1.00, 11/03, page 208 of 376 14.5.3 Serial Data Transmission Figure 14.11 shows an example of SCI3 operation for transmission in clocked synchronous mode. In serial transmission, SCI3 operates as described below. 1. SCI3 monitors the TDRE flag in SSR, and if the flag is 0, SCI3 recognizes that data has been written to TDR, and transfers the data from TDR to TSR. 2. SCI3 sets the TDRE flag to 1 and starts transmission. If the TIE bit in SCR3 is set to 1 at this time, a transmit data empty interrupt (TXI) is generated. 3. 8-bit data is sent from the TXD pin synchronized with the output clock when output clock mode has been specified, and synchronized with the input clock when use of an external clock has been specified. Serial data is transmitted sequentially from the LSB (bit 0), from the TXD pin. 4. SCI3 checks the TDRE flag at the timing for sending the MSB (bit 7). 5. If the TDRE flag is cleared to 0, data is transferred from TDR to TSR, and serial transmission of the next frame is started. 6. If the TDRE flag is set to 1, the TEND flag in SSR is set to 1, and the TDRE flag maintains the output state of the last bit. If the TEIE bit in SCR3 is set to 1 at this time, a TEI interrupt request is generated. The SCK3 pin is fixed high at the end of transmission. 7. Figure 14.12 shows a sample flow chart for serial data transmission. Even if the TDRE flag is cleared to 0, transmission will not start while a receive error flag (OER, FER, or PER) is set to 1. Make sure that the receive error flags are cleared to 0 before starting transmission. Serial clock Serial data Bit 0 Bit 1 Bit 7 Bit 0 Bit 1 Bit 6 Bit 7 1 frame TDRE TEND TXI interrupt LSI operation request generated User processing TDRE flag cleared to 0 Data written to TDR 1 frame TXI interrupt request generated TEI interrupt request generated Figure 14.11 Example of SCI3 Transmission in Clocked Synchronous Mode Rev. 1.00, 11/03, page 209 of 376 Start transmission [1] [1] Read TDRE flag in SSR No TDRE = 1 Yes [2] Read SSR and check that the TDRE flag is set to 1, then write transmit data to TDR. When data is written to TDR, the TDRE flag is automatically cleared to 0 and clocks are output to start the data transmission. To continue serial transmission, be sure to read 1 from the TDRE flag to confirm that writing is possible, then write data to TDR. When data is written to TDR, the TDRE flag is automatically cleared to 0. Write transmit data to TDR [2] All data transmitted? No Yes Read TEND flag in SSR No TEND = 1 Yes Clear TE bit in SCR3 to 0 Figure 14.12 Sample Serial Transmission Flowchart (Clocked Synchronous Mode) Rev. 1.00, 11/03, page 210 of 376 14.5.4 Serial Data Reception (Clocked Synchronous Mode) Figure 14.13 shows an example of SCI3 operation for reception in clocked synchronous mode. In serial reception, SCI3 operates as described below. 1. 2. 3. SCI3 performs internal initialization synchronous with a synchronization clock input or output, starts receiving data. SCI3 stores the receive data in RSR. If an overrun error occurs (when reception of the next data is completed while the RDRF flag in SSR is still set to 1), the OER bit in SSR is set to 1. If the RIE bit in SCR3 is set to 1 at this time, an ERI interrupt request is generated, receive data is not transferred to RDR, and the RDRF flag remains to be set to 1. If reception is completed successfully, the RDRF bit in SSR is set to 1, and receive data is transferred to RDR. If the RIE bit in SCR3 is set to 1 at this time, an RXI interrupt request is generated. 4. Serial clock Serial data Bit 7 Bit 0 Bit 7 Bit 0 Bit 1 Bit 6 Bit 7 1 frame RDRF OER LSI operation User processing RXI interrupt request generated RDRF flag cleared to 0 RDR data read 1 frame RXI interrupt request generated ERI interrupt request generated by overrun error Overrun error processing RDR data has not been read (RDRF = 1) Figure 14.13 Example of SCI3 Reception in Clocked Synchronous Mode Reception cannot be resumed while a receive error flag is set to 1. Accordingly, clear the OER, FER, PER, and RDRF bits to 0 before resuming reception. Figure 14.14 shows a sample flow chart for serial data reception. Rev. 1.00, 11/03, page 211 of 376 Start reception [1] Read OER flag in SSR [1] [2] Yes OER = 1 [4] No Error processing (Continued below) Read RDRF flag in SSR [2] [4] RDRF = 1 Yes [3] Read the OER flag in SSR to determine if there is an error. If an overrun error has occurred, execute overrun error processing. Read SSR and check that the RDRF flag is set to 1, then read the receive data in RDR. When data is read from RDR, the RDRF flag is automatically cleared to 0. To continue serial reception, before the MSB (bit 7) of the current frame is received, reading the RDRF flag and reading RDR should be finished. When data is read from RDR, the RDRF flag is automatically cleared to 0. If an overrun error occurs, read the OER flag in SSR, and after performing the appropriate error processing, clear the OER flag to 0. Reception cannot be resumed if the OER flag is set to 1. No Read receive data in RDR Yes All data received? No Clear RE bit in SCR3 to 0 [4] Error processing Overrun error processing Clear OER flag in SSR to 0 Figure 14.14 Sample Serial Reception Flowchart (Clocked Synchronous Mode) Rev. 1.00, 11/03, page 212 of 376 14.5.5 Simultaneous Serial Data Transmission and Reception Figure 14.15 shows a sample flowchart for simultaneous serial transmit and receive operations. The following procedure should be used for simultaneous serial data transmit and receive operations. To switch from transmit mode to simultaneous transmit and receive mode, after checking that SCI3 has finished transmission and the TDRE and TEND flags are set to 1, clear TE to 0. Then simultaneously set TE and RE to 1 with a single instruction. To switch from receive mode to simultaneous transmit and receive mode, after checking that SCI3 has finished reception, clear RE to 0. Then after checking that the RDRF and receive error flags (OER, FER, and PER) are cleared to 0, simultaneously set TE and RE to 1 with a single instruction. Rev. 1.00, 11/03, page 213 of 376 Start transmission/reception Read TDRE flag in SSR No TDRE = 1 Yes Write transmit data to TDR [1] Read OER flag in SSR Yes OER = 1 No Read RDRF flag in SSR No RDRF = 1 Yes Read receive data in RDR [2] [4] Overrun error processing Read SSR and check that the TDRE flag is set to 1, then write transmit data to TDR. When data is written to TDR, the TDRE flag is automatically cleared to 0. [2] Read SSR and check that the RDRF flag is set to 1, then read the receive data in RDR. When data is read from RDR, the RDRF flag is automatically cleared to 0. [3] To continue serial transmission/ reception, before the MSB (bit 7) of the current frame is received, finish reading the RDRF flag, reading RDR. Also, before the MSB (bit 7) of the current frame is transmitted, read 1 from the TDRE flag to confirm that writing is possible. Then write data to TDR. When data is written to TDR, the TDRE flag is automatically cleared to 0. When data is read from RDR, the RDRF flag is automatically cleared to 0. [4] If an overrun error occurs, read the OER flag in SSR, and after performing the appropriate error processing, clear the OER flag to 0. Transmission/reception cannot be resumed if the OER flag is set to 1. For overrun error processing, see figure 14.14. [1] Yes All data received? No [3] Clear TE and RE bits in SCR to 0 Figure 14.15 Sample Flowchart of Simultaneous Serial Transmit and Receive Operations (Clocked Synchronous Mode) Rev. 1.00, 11/03, page 214 of 376 14.6 Multiprocessor Communication Function Use of the multiprocessor communication function enables data transfer between a number of processors sharing communication lines by asynchronous serial communication using the multiprocessor format, in which a multiprocessor bit is added to the transfer data. When multiprocessor communication is performed, each receiving station is addressed by a unique ID code. The serial communication cycle consists of two component cycles; an ID transmission cycle that specifies the receiving station, and a data transmission cycle. The multiprocessor bit is used to differentiate between the ID transmission cycle and the data transmission cycle. If the multiprocessor bit is 1, the cycle is an ID transmission cycle; if the multiprocessor bit is 0, the cycle is a data transmission cycle. Figure 14.16 shows an example of inter-processor communication using the multiprocessor format. The transmitting station first sends the ID code of the receiving station with which it wants to perform serial communication as data with a 1 multiprocessor bit added. It then sends transmit data as data with a 0 multiprocessor bit added. When data with a 1 multiprocessor bit is received, the receiving station compares that data with its own ID. The station whose ID matches then receives the data sent next. Stations whose IDs do not match continue to skip data until data with a 1 multiprocessor bit is again received. SCI3 uses the MPIE bit in SCR3 to implement this function. When the MPIE bit is set to 1, transfer of receive data from RSR to RDR, error flag detection, and setting the SSR status flags, RDRF, FER, and OER, to 1, are inhibited until data with a 1 multiprocessor bit is received. On reception of a receive character with a 1 multiprocessor bit, the MPBR bit in SSR is set to 1 and the MPIE bit is automatically cleared, thus normal reception is resumed. If the RIE bit in SCR3 is set to 1 at this time, an RXI interrupt is generated. When the multiprocessor format is selected, the parity bit setting is rendered invalid. All other bit settings are the same as those in normal asynchronous mode. The clock used for multiprocessor communication is the same as that in normal asynchronous mode. Rev. 1.00, 11/03, page 215 of 376 Transmitting station Serial transmission line Receiving station A (ID = 01) Serial data Receiving station B (ID = 02) H'01 (MPB = 1) Receiving station C (ID = 03) H'AA (MPB = 0) Receiving station D (ID = 04) ID transmission cycle = Data transmission cycle = receiving station Data transmission to specification receiving station specified by ID [Legend] MPB: Multiprocessor bit Figure 14.16 Example of Inter-Processor Communication Using Multiprocessor Format (Transmission of Data H'AA to Receiving Station A) Rev. 1.00, 11/03, page 216 of 376 14.6.1 Multiprocessor Serial Data Transmission Figure 14.17 shows a sample flowchart for multiprocessor serial data transmission. For an ID transmission cycle, set the MPBT bit in SSR to 1 before transmission. For a data transmission cycle, clear the MPBT bit in SSR to 0 before transmission. All other SCI3 operations are the same as those in asynchronous mode. Start transmission [1] [1] Read TDRE flag in SSR Read SSR and check that the TDRE flag is set to 1, set the MPBT bit in SSR to 0 or 1, then write transmit data to TDR. When data is written to TDR, the TDRE flag is automatically cleared to 0. To continue serial transmission, be sure to read 1 from the TDRE flag to confirm that writing is possible, then write data to TDR. When data is written to TDR, the TDRE flag is automatically cleared to 0. To output a break in serial transmission, set the port PCR to 1, clear PDR to 0, then clear the TE bit in SCR3 to 0. No TDRE = 1 [2] Yes Set MPBT bit in SSR [3] Write transmit data to TDR Yes [2] All data transmitted? No Read TEND flag in SSR No TEND = 1 Yes No [3] Break output? Yes Clear PDR to 0 and set PCR to 1 Clear TE bit in SCR3 to 0 Figure 14.17 Sample Multiprocessor Serial Transmission Flowchart Rev. 1.00, 11/03, page 217 of 376 14.6.2 Multiprocessor Serial Data Reception Figure 14.18 shows a sample flowchart for multiprocessor serial data reception. If the MPIE bit in SCR3 is set to 1, data is skipped until data with a 1 multiprocessor bit is sent. On receiving data with a 1 multiprocessor bit, the receive data is transferred to RDR. An RXI interrupt request is generated at this time. All other SCI3 operations are the same as those in asynchronous mode. Figure 14.19 shows an example of SCI3 operation for multiprocessor format reception. Rev. 1.00, 11/03, page 218 of 376 Start reception [1] [2] [1] [2] Yes [3] Set MPIE bit in SCR3 to 1 Read OER and FER flags in SSR FER+OER = 1 No Read RDRF flag in SSR No RDRF = 1 Yes Read receive data in RDR No This station's ID? Yes Read OER and FER flags in SSR Yes FER+OER = 1 No Read RDRF flag in SSR No RDRF = 1 Yes Read receive data in RDR Yes All data received? No [A] Clear RE bit in SCR3 to 0 Set the MPIE bit in SCR3 to 1. Read OER and FER in SSR to check for errors. Receive error processing is performed in cases where a receive error occurs. Read SSR and check that the RDRF flag is set to 1, then read the receive data in RDR and compare it with this station's ID. If the data is not this station's ID, set the MPIE bit to 1 again. When data is read from RDR, the RDRF flag is automatically cleared to 0. Read SSR and check that the RDRF flag is set to 1, then read the data in RDR. If a receive error occurs, read the OER and FER flags in SSR to identify the error. After performing the appropriate error processing, ensure that the OER and FER flags are all cleared to 0. Reception cannot be resumed if either of these flags is set to 1. In the case of a framing error, a break can be detected by reading the RxD pin value. [5] Error processing (Continued on next page) Figure 14.18 Sample Multiprocessor Serial Reception Flowchart (1) Rev. 1.00, 11/03, page 219 of 376 [5] Error processing No OER = 1 Yes Overrun error processing No FER = 1 Yes Yes Break? No Framing error processing [A] Clear OER, and FER flags in SSR to 0 Figure 14.18 Sample Multiprocessor Serial Reception Flowchart (2) Rev. 1.00, 11/03, page 220 of 376 Start bit Serial data 1 0 D0 Receive data (ID1) D1 1 frame D7 MPB 1 Stop Start bit bit 1 0 D0 Receive data (Data1) D1 1 frame D7 MPB 0 Stop bit 1 Mark state (idle state) 1 MPIE RDRF RDR value LSI operation User processing RXI interrupt request MPIE cleared to 0 RDRF flag cleared to 0 RDR data read When data is not this station's ID, MPIE is set to 1 again ID1 RXI interrupt request is not generated, and RDR retains its state (a) When data does not match this receiver's ID Start bit Serial data 1 0 D0 Receive data (ID2) D1 1 frame D7 MPB 1 Stop Start bit bit 1 0 D0 Receive data (Data2) D1 1 frame D7 MPB 0 Stop bit 1 Mark state (idle state) 1 MPIE RDRF RDR value LSI operation User processing ID1 ID2 Data2 RXI interrupt request MPIE cleared to 0 RDRF flag cleared to 0 RDR data read RXI interrupt request When data is this station's ID, reception is continued RDRF flag cleared to 0 RDR data read MPIE set to 1 again (b) When data matches this receiver's ID Figure 14.19 Example of SCI3 Reception Using Multiprocessor Format (Example with 8-Bit Data, Multiprocessor Bit, One Stop Bit) Rev. 1.00, 11/03, page 221 of 376 14.7 Interrupts SCI3 creates the following six interrupt requests: transmission end, transmit data empty, receive data full, and receive errors (overrun error, framing error, and parity error). Table 14.6 shows the interrupt sources. Table 14.6 SCI3 Interrupt Requests Interrupt Requests Receive Data Full Transmit Data Empty Transmission End Receive Error Abbreviation RXI TXI TEI ERI Interrupt Sources Setting RDRF in SSR Setting TDRE in SSR Setting TEND in SSR Setting OER, FER, and PER in SSR The initial value of the TDRE flag in SSR is 1. Thus, when the TIE bit in SCR3 is set to 1 before transferring the transmit data to TDR, a TXI interrupt request is generated even if the transmit data is not ready. The initial value of the TEND flag in SSR is 1. Thus, when the TEIE bit in SCR3 is set to 1 before transferring the transmit data to TDR, a TEI interrupt request is generated even if the transmit data has not been sent. It is possible to make use of the most of these interrupt requests efficiently by transferring the transmit data to TDR in the interrupt routine. To prevent the generation of these interrupt requests (TXI and TEI), set the enable bits (TIE and TEIE) that correspond to these interrupt requests to 1, after transferring the transmit data to TDR. Rev. 1.00, 11/03, page 222 of 376 14.8 14.8.1 Usage Notes Break Detection and Processing When framing error detection is performed, a break can be detected by reading the RXD pin value directly. In a break, the input from the RXD pin becomes all 0s, setting the FER flag, and possibly the PER flag. Note that as SCI3 continues the receive operation after receiving a break, even if the FER flag is cleared to 0, it will be set to 1 again. 14.8.2 Mark State and Break Sending When TE is 0, the TXD pin is used as an I/O port whose direction (input or output) and level are determined by PCR and PDR. This can be used to set the TXD pin to mark state (high level) or send a break during serial data transmission. To maintain the communication line at mark state until TE is set to 1, set both PCR and PDR to 1. As TE is cleared to 0 at this point, the TXD pin becomes an I/O port, and 1 is output from the TXD pin. To send a break during serial transmission, first set PCR to 1 and clear PDR to 0, and then clear TE to 0. When TE is cleared to 0, the transmitter is initialized regardless of the current transmission state, the TXD pin becomes an I/O port, and 0 is output from the TXD pin. 14.8.3 Receive Error Flags and Transmit Operations (Clocked Synchronous Mode Only) Transmission cannot be started when a receive error flag (OER, PER, or FER) is set to 1, even if the TDRE flag is cleared to 0. Be sure to clear the receive error flags to 0 before starting transmission. Note also that receive error flags cannot be cleared to 0 even if the RE bit is cleared to 0. Rev. 1.00, 11/03, page 223 of 376 14.8.4 Receive Data Sampling Timing and Reception Margin in Asynchronous Mode In asynchronous mode, SCI3 operates on a basic clock with a frequency of 16 times the transfer rate. In reception, SCI3 samples the falling edge of the start bit using the basic clock, and performs internal synchronization. Receive data is latched internally at the rising edge of the 8th pulse of the basic clock as shown in figure 14.20. Thus, the reception margin in asynchronous mode is given by formula (1) below. 1 D - 0.5 M = (0.5 - )- - (L - 0.5) F x 100(%) 2N N ... Formula (1) Legend N D L F : Ratio of bit rate to clock (N = 16) : Clock duty (D = 0.5 to 1.0) : Frame length (L = 9 to 12) : Absolute value of clock rate deviation Assuming values of F (absolute value of clock rate deviation) = 0 and D (clock duty) = 0.5 in formula (1), the reception margin can be given by the formula. M = {0.5 - 1/(2 x 16)} x 100 [%] = 46.875% However, this is only the computed value, and a margin of 20% to 30% should be allowed for in system design. 16 clocks 8 clocks 0 Internal basic clock Receive data (RxD) Synchronization sampling timing Data sampling timing 7 15 0 7 15 0 Start bit D0 D1 Figure 14.20 Receive Data Sampling Timing in Asynchronous Mode Rev. 1.00, 11/03, page 224 of 376 Section 15 I2C Bus Interface 2 (IIC2) The I2C bus interface 2 conforms to and provides a subset of the Philips I2C bus (inter-IC bus) interface functions. The register configuration that controls the I2C bus differs partly from the Philips configuration, however. Figure 15.1 shows a block diagram of the I2C bus interface 2. Figure 15.2 shows an example of I/O pin connections to external circuits. 15.1 Features * Selection of I2C format or clocked synchronous serial format * Continuous transmission/reception Since the shift register, transmit data register, and receive data register are independent from each other, the continuous transmission/reception can be performed. I2C bus format: * Start and stop conditions generated automatically in master mode * Selection of acknowledge output levels when receiving * Automatic loading of acknowledge bit when transmitting * Bit synchronization/wait function In master mode, the state of SCL is monitored per bit, and the timing is synchronized automatically. If transmission/reception is not yet possible, set the SCL to low until preparations are completed. * Six interrupt sources Transmit data empty (including slave-address match), transmit end, receive data full (including slave-address match), arbitration lost, NACK detection, and stop condition detection * Direct bus drive Two pins, SCL and SDA pins, function as NMOS open-drain outputs when the bus drive function is selected. Clocked synchronous format: * Four interrupt sources Transmit-data-empty, transmit-end, receive-data-full, and overrun error IFIIC10A_000020030300 Rev. 1.00, 11/03, page 225 of 376 Transfer clock generation circuit SCL Output control Transmit/ receive control circuit ICCR1 ICCR2 ICMR Noise canceler ICDRT SAR Internal data bus SDA Output control ICDRS Noise canceler Address comparator ICDRR Bus state decision circuit Arbitration decision circuit ICIER ICSR [Legend] ICCR1: ICCR2: ICMR: ICSR: ICIER: ICDRT: ICDRR: ICDRS: SAR: I2C bus control register 1 I2C bus control register 2 I2C bus mode register I2C bus status register I2C bus interrupt enable register I2C bus transmit data register I2C bus receive data register I2C bus shift register Slave address register Interrupt generator Interrupt request Figure 15.1 Block Diagram of I2C Bus Interface 2 Rev. 1.00, 11/03, page 226 of 376 Vcc Vcc SCL in out SCL SCL SDA in out (Master) SDA SDA SCL SDA SCL in out SDA in out (Slave 1) SCL in out SDA in out (Slave 2) Figure 15.2 External Circuit Connections of I/O Pins 15.2 Input/Output Pins Table 15.1 summarizes the input/output pins used by the I2C bus interface 2. Table 15.1 Pin Configuration Name Serial clock Serial data Abbreviation SCL SDA I/O I/O I/O Function I C serial clock input/output I C serial data input/output 2 2 15.3 Register Descriptions The I2C bus interface 2 has the following registers. * I2C bus control register 1 (ICCR1) * I2C bus control register 2 (ICCR2) * I2C bus mode register (ICMR) * I2C bus interrupt enable register (ICIER) * I2C bus status register (ICSR) * I2C bus slave address register (SAR) * I2C bus transmit data register (ICDRT) * I2C bus receive data register (ICDRR) * I2C bus shift register (ICDRS) Rev. 1.00, 11/03, page 227 of 376 SCL SDA 15.3.1 I2C Bus Control Register 1 (ICCR1) ICCR1 enables or disables the I2C bus interface 2, controls transmission or reception, and selects master or slave mode, transmission or reception, and transfer clock frequency in master mode. Bit 7 Bit Name Initial Value R/W ICE 0 R/W Description I C Bus Interface Enable 0: This module is halted. (SCL and SDA pins are set to port function.) 1: This bit is enabled for transfer operations. (SCL and SDA pins are bus drive state.) 6 RCVD 0 R/W Reception Disable This bit enables or disables the next operation when TRS is 0 and ICDRR is read. 0: Enables next reception 1: Disables next reception 5 4 MST TRS 0 0 R/W R/W Master/Slave Select Transmit/Receive Select In master mode with the I C bus format, when arbitration is lost, MST and TRS are both reset by hardware, causing a transition to slave receive mode. Modification of the TRS bit should be made between transfer frames. After data receive has been started in slave receive mode, when the first seven bits of the receive data agree with the slave address that is set to SAR and the eighth bit is 1, TRS is automatically set to 1. If an overrun error occurs in master mode with the clock synchronous serial format, MST is cleared to 0 and slave receive mode is entered. Operating modes are described below according to MST and TRS combination. When clocked synchronous serial format is selected and MST is 1, clock is output. 00: Slave receive mode 01: Slave transmit mode 10: Master receive mode 11: Master transmit mode 3 to 0 CKS3 to CKS0 All 0 R/W Transfer Clock Select 3 to 0 These bits should be set according to the necessary transfer rate in master mode. In slave mode, these bits are used reservation of the set up time in transmit mode. The time is 10Tcyc when CKS3 = 0, and 20Tcyc when CKS3 = 1. (see table 15.2) 2 2 Rev. 1.00, 11/03, page 228 of 376 Table 15.2 Transfer Rate Bit 3 0 Bit 2 0 Bit 1 CKS1 0 1 1 0 1 1 0 0 1 1 0 1 Bit 0 CKS0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Clock /28 /40 /48 /64 /80 /100 /112 /128 /56 /80 /96 /128 /160 /200 /224 /256 = 5 MHz 179 kHz 125 kHz 104 kHz 78.1 kHz 62.5 kHz 50.0 kHz 44.6 kHz 39.1 kHz 89.3 kHz 62.5 kHz 52.1 kHz 39.1 kHz 31.3 kHz 25.0 kHz 22.3 kHz 19.5 kHz Transfer Rate = 8 MHz 286 kHz 200 kHz 167 kHz 125 kHz 100 kHz 80.0 kHz 71.4 kHz 62.5 kHz 143 kHz 100 kHz 83.3 kHz 62.5 kHz 50.0 kHz 40.0 kHz 35.7 kHz 31.3 kHz CKS3 CKS2 = 10 MHz 357 kHz 250 kHz 208 kHz 156 kHz 125 kHz 100 kHz 89.3 kHz 78.1 kHz 179 kHz 125 kHz 104 kHz 78.1 kHz 62.5 kHz 50.0 kHz 44.6 kHz 39.1 kHz 15.3.2 I2C Bus Control Register 2 (ICCR2) ICCR2 issues start/stop conditions, manipulates the SDA pin, monitors the SCL pin, and controls reset in the control part of the I2C bus interface 2. Bit 7 Bit Name BBSY Initial Value R/W Description 0 R/W Bus Busy This bit enables to confirm whether the I C bus is occupied or released and to issue start/stop conditions in master mode. With the clocked synchronous serial format, this bit 2 has no meaning. With the I C bus format, this bit is set to 1 when the SDA level changes from high to low under the condition of SCL = high, assuming that the start condition has been issued. This bit is cleared to 0 when the SDA level changes from low to high under the condition of SCL = high, assuming that the stop condition has been issued. Write 1 to BBSY and 0 to SCP to issue a start condition. Follow this procedure when also re-transmitting a start condition. Write 0 in BBSY and 0 in SCP to issue a stop condition. To issue start/stop conditions, use the MOV instruction. 2 Rev. 1.00, 11/03, page 229 of 376 Bit 6 Bit Name SCP Initial Value R/W Description 1 R/W Start/Stop Issue Condition Disable The SCP bit controls the issue of start/stop conditions in master mode. To issue a start condition, write 1 in BBSY and 0 in SCP. A retransmit start condition is issued in the same way. To issue a stop condition, write 0 in BBSY and 0 in SCP. This bit is always read as 1. If 1 is written, the data is not stored. 5 SDAO 1 R/W SDA Output Value Control This bit is used with SDAOP when modifying output level of SDA. This bit should not be manipulated during transfer. 0: When reading, SDA pin outputs low. When writing, SDA pin is changed to output low. 1: When reading, SDA pin outputs high. When writing, SDA pin is changed to output Hi-Z (outputs high by external pull-up resistance). 4 SDAOP 1 R/W SDAO Write Protect This bit controls change of output level of the SDA pin by modifying the SDAO bit. To change the output level, clear SDAO and SDAOP to 0 or set SDAO to 1 and clear SDAOP to 0 by the MOV instruction. This bit is always read as 1. 3 2 1 SCLO IICRST 1 1 0 R This bit monitors SCL output level. When SCLO is 1, SCL pin outputs high. When SCLO is 0, SCL pin outputs low. Reserved This bit is always read as 1. R/W IIC Control Part Reset This bit resets the control part except for I C registers. If this bit is set to 1 when hang-up occurs because of 2 2 communication failure during I C operation, I C control part can be reset without setting ports and initializing registers. 2 0 1 Reserved This bit is always read as 1. Rev. 1.00, 11/03, page 230 of 376 15.3.3 I2C Bus Mode Register (ICMR) ICMR selects whether the MSB or LSB is transferred first, performs master mode wait control, and selects the transfer bit count. Bit 7 Bit Name MLS Initial Value R/W Description 0 R/W MSB-First/LSB-First Select 0: MSB-first 1: LSB-first Set this bit to 0 when the I C bus format is used. 6 WAIT 0 R/W Wait Insertion Bit In master mode with the I C bus format, this bit selects whether to insert a wait after data transfer except the acknowledge bit. When WAIT is set to 1, after the fall of the clock for the final data bit, low period is extended for two transfer clocks. If WAIT is cleared to 0, data and acknowledge bits are transferred consecutively with no wait inserted. The setting of this bit is invalid in slave mode with the I C bus format or with the clocked synchronous serial format. 5, 4 3 BCWP All 1 1 Reserved These bits are always read as 1. R/W BC Write Protect This bit controls the BC2 to BC0 modifications. When modifying BC2 to BC0, this bit should be cleared to 0 and use the MOV instruction. In clock synchronous serial mode, BC should not be modified. 0: When writing, values of BC2 to BC0 are set. 1: When reading, 1 is always read. When writing, settings of BC2 to BC0 are invalid. 2 2 2 Rev. 1.00, 11/03, page 231 of 376 Bit 2 1 0 Bit Name BC2 BC1 BC0 Initial Value R/W Description 0 0 0 R/W Bit Counter 2 to 0 R/W These bits specify the number of bits to be transferred next. R/W When read, the remaining number of transfer bits is 2 indicated. With the I C bus format, the data is transferred with one addition acknowledge bit. Bit BC2 to BC0 settings should be made during an interval between transfer frames. If bits BC2 to BC0 are set to a value other than 000, the setting should be made while the SCL pin is low. The value returns to 000 at the end of a data transfer, including the acknowledge bit. With the clock synchronous serial format, these bits should not be modified. I C Bus Format 000: 9 bits 001: 2 bits 010: 3 bits 011: 4 bits 100: 5 bits 101: 6 bits 110: 7 bits 111: 8 bits 2 Clock Synchronous Serial Format 000: 8 bits 001: 1 bits 010: 2 bits 011: 3 bits 100: 4 bits 101: 5 bits 110: 6 bits 111: 7 bits 15.3.4 I2C Bus Interrupt Enable Register (ICIER) ICIER enables or disables interrupt sources and acknowledge bits, sets acknowledge bits to be transferred, and confirms acknowledge bits to be received. Bit 7 Bit Name TIE Initial Value R/W Description 0 R/W Transmit Interrupt Enable When the TDRE bit in ICSR is set to 1, this bit enables or disables the transmit data empty interrupt (TXI). 0: Transmit data empty interrupt request (TXI) is disabled. 1: Transmit data empty interrupt request (TXI) is enabled. 6 TEIE 0 R/W Transmit End Interrupt Enable This bit enables or disables the transmit end interrupt (TEI) at the rising of the ninth clock while the TDRE bit in ICSR is 1. TEI can be canceled by clearing the TEND bit or the TEIE bit to 0. 0: Transmit end interrupt request (TEI) is disabled. 1: Transmit end interrupt request (TEI) is enabled. Rev. 1.00, 11/03, page 232 of 376 Bit 5 Bit Name RIE Initial Value R/W Description 0 R/W Receive Interrupt Enable This bit enables or disables the receive data full interrupt request (RXI) and the overrun error interrupt request (ERI) with the clocked synchronous format, when a receive data is transferred from ICDRS to ICDRR and the RDRF bit in ICSR is set to 1. RXI can be canceled by clearing the RDRF or RIE bit to 0. 0: Receive data full interrupt request (RXI) and overrun error interrupt request (ERI) with the clocked synchronous format are disabled. 1: Receive data full interrupt request (RXI) and overrun error interrupt request (ERI) with the clocked synchronous format are enabled. 4 NAKIE 0 R/W NACK Receive Interrupt Enable This bit enables or disables the NACK receive interrupt request (NAKI) and the overrun error (setting of the OVE bit in ICSR) interrupt request (ERI) with the clocked synchronous format, when the NACKF and AL bits in ICSR are set to 1. NAKI can be canceled by clearing the NACKF, OVE, or NAKIE bit to 0. 0: NACK receive interrupt request (NAKI) is disabled. 1: NACK receive interrupt request (NAKI) is enabled. 3 STIE 0 R/W Stop Condition Detection Interrupt Enable 0: Stop condition detection interrupt request (STPI) is disabled. 1: Stop condition detection interrupt request (STPI) is enabled. 2 ACKE 0 R/W Acknowledge Bit Judgement Select 0: The value of the receive acknowledge bit is ignored, and continuous transfer is performed. 1: If the receive acknowledge bit is 1, continuous transfer is halted. 1 ACKBR 0 R Receive Acknowledge In transmit mode, this bit stores the acknowledge data that are returned by the receive device. This bit cannot be modified. 0: Receive acknowledge = 0 1: Receive acknowledge = 1 Rev. 1.00, 11/03, page 233 of 376 Bit 0 Bit Name ACKBT Initial Value R/W Description 0 R/W Transmit Acknowledge In receive mode, this bit specifies the bit to be sent at the acknowledge timing. 0: 0 is sent at the acknowledge timing. 1: 1 is sent at the acknowledge timing. 15.3.5 I2C Bus Status Register (ICSR) ICSR performs confirmation of interrupt request flags and status. Bit 7 Bit Name TDRE Initial Value R/W Description 0 R/W Transmit Data Register Empty [Setting conditions] * * * * When data is transferred from ICDRT to ICDRS and ICDRT becomes empty When TRS is set When a start condition (including re-transfer) has been issued When transmit mode is entered from receive mode in slave mode When 0 is written in TDRE after reading TDRE = 1 When data is written to ICDRT with an instruction [Clearing conditions] * * 6 TEND 0 R/W Transmit End [Setting conditions] * * When the ninth clock of SCL rises with the I C bus format while the TDRE flag is 1 When the final bit of transmit frame is sent with the clock synchronous serial format When 0 is written in TEND after reading TEND = 1 When data is written to ICDRT with an instruction 2 [Clearing conditions] * * Rev. 1.00, 11/03, page 234 of 376 Bit 5 Bit Name RDRF Initial Value R/W Description 0 R/W Receive Data Register Full [Setting condition] * * * When a receive data is transferred from ICDRS to ICDRR When 0 is written in RDRF after reading RDRF = 1 When ICDRR is read with an instruction [Clearing conditions] 4 NACKF 0 R/W No Acknowledge Detection Flag [Setting condition] * When no acknowledge is detected from the receive device in transmission while the ACKE bit in ICIER is 1 When 0 is written in NACKF after reading NACKF = 1 [Clearing condition] * 3 STOP 0 R/W Stop Condition Detection Flag [Setting condition] * * 2 AL/OVE 0 When a stop condition is detected after frame transfer When 0 is written in STOP after reading STOP = 1 [Clearing condition] R/W Arbitration Lost Flag/Overrun Error Flag This flag indicates that arbitration was lost in master mode 2 with the I C bus format and that the final bit has been received while RDRF = 1 with the clocked synchronous format. When two or more master devices attempt to seize the bus 2 at nearly the same time, if the I C bus interface detects data differing from the data it sent, it sets AL to 1 to indicate that the bus has been taken by another master. [Setting conditions] * * * If the internal SDA and SDA pin disagree at the rise of SCL in master transmit mode When the SDA pin outputs high in master mode while a start condition is detected When the final bit is received with the clocked synchronous format while RDRF = 1 When 0 is written in AL/OVE after reading AL/OVE=1 [Clearing condition] * Rev. 1.00, 11/03, page 235 of 376 Bit 1 Bit Name AAS Initial Value R/W Description 0 R/W Slave Address Recognition Flag In slave receive mode, this flag is set to 1 if the first frame following a start condition matches bits SVA6 to SVA0 in SAR. [Setting conditions] * * When the slave address is detected in slave receive mode When the general call address is detected in slave receive mode. When 0 is written in AAS after reading AAS=1 2 [Clearing condition] * 0 ADZ 0 R/W General Call Address Recognition Flag This bit is valid in I C bus format slave receive mode. [Setting condition] * When the general call address is detected in slave receive mode When 0 is written in ADZ after reading ADZ=1 [Clearing condition] * 15.3.6 Slave Address Register (SAR) SAR selects the communication format and sets the slave address. When the chip is in slave mode with the I2C bus format, if the upper 7 bits of SAR match the upper 7 bits of the first frame received after a start condition, the chip operates as the slave device. Bit Bit Name Initial Value R/W Description All 0 R/W Slave Address 6 to 0 These bits set a unique address in bits SVA6 to SVA0, differing form the addresses of other slave devices 2 connected to the I C bus. 0 R/W Format Select 0: I C bus format is selected. 1: Clocked synchronous serial format is selected. 2 7 to 1 SVA6 to SVA0 0 FS Rev. 1.00, 11/03, page 236 of 376 15.3.7 I2C Bus Transmit Data Register (ICDRT) ICDRT is an 8-bit readable/writable register that stores the transmit data. When ICDRT detects the space in the shift register (ICDRS), it transfers the transmit data which is written in ICDRT to ICDRS and starts transferring data. If the next transfer data is written to ICDRT during transferring data of ICDRS, continuous transfer is possible. If the MLS bit of ICMR is set to 1 and when the data is written to ICDRT, the MSB/LSB inverted data is read. The initial value of ICDRT is H'FF. 15.3.8 I2C Bus Receive Data Register (ICDRR) ICDRR is an 8-bit register that stores the receive data. When data of one byte is received, ICDRR transfers the receive data from ICDRS to ICDRR and the next data can be received. ICDRR is a receive-only register, therefore the CPU cannot write to this register. The initial value of ICDRR is H'FF. 15.3.9 I2C Bus Shift Register (ICDRS) ICDRS is a register that is used to transfer/receive data. In transmission, data is transferred from ICDRT to ICDRS and the data is sent from the SDA pin. In reception, data is transferred from ICDRS to ICDRR after data of one byte is received. This register cannot be read directly from the CPU. Rev. 1.00, 11/03, page 237 of 376 15.4 Operation The I2C bus interface can communicate either in I2C bus mode or clocked synchronous serial mode by setting FS in SAR. 15.4.1 I2C Bus Format Figure 15.3 shows the I2C bus formats. Figure 15.4 shows the I2C bus timing. The first frame following a start condition always consists of 8 bits. (a) I2C bus format (FS = 0) S 1 SLA 7 1 R/ 1 A 1 DATA n A 1 m A/ 1 P 1 n: Transfer bit count (n = 1 to 8) m: Transfer frame count (m 1) (b) I2C bus format (Start condition retransmission, FS = 0) S 1 SLA 7 1 R/ 1 A 1 DATA n1 m1 A/ 1 S 1 SLA 7 1 R/ 1 A 1 DATA n2 m2 A/ 1 P 1 n1 and n2: Transfer bit count (n1 and n2 = 1 to 8) m1 and m2: Transfer frame count (m1 and m2 1) Figure 15.3 I2C Bus Formats SDA SCL S 1-7 SLA 8 R/ 9 A 1-7 DATA 8 9 A 1-7 DATA 8 9 A P Figure 15.4 I2C Bus Timing [Legend] S: Start condition. The master device drives SDA from high to low while SCL is high. SLA: Slave address R/W: Indicates the direction of data transfer: from the slave device to the master device when R/W is 1, or from the master device to the slave device when R/W is 0. A: Acknowledge. The receive device drives SDA to low. DATA: Transfer data P: Stop condition. The master device drives SDA from low to high while SCL is high. Rev. 1.00, 11/03, page 238 of 376 15.4.2 Master Transmit Operation In master transmit mode, the master device outputs the transmit clock and transmit data, and the slave device returns an acknowledge signal. For master transmit mode operation timing, refer to figures 15.5 and 15.6. The transmission procedure and operations in master transmit mode are described below. 1. Set the ICE bit in ICCR1 to 1. Set the MLS and WAIT bits in ICMR and the CKS3 to CKS0 bits in ICCR1 to 1. (Initial setting) 2. Read the BBSY flag in ICCR2 to confirm that the bus is free. Set the MST and TRS bits in ICCR1 to select master transmit mode. Then, write 1 to BBSY and 0 to SCP using MOV instruction. (Start condition issued) This generates the start condition. 3. After confirming that TDRE in ICSR has been set, write the transmit data (the first byte data show the slave address and R/W) to ICDRT. At this time, TDRE is automatically cleared to 0, and data is transferred from ICDRT to ICDRS. TDRE is set again. 4. When transmission of one byte data is completed while TDRE is 1, TEND in ICSR is set to 1 at the rise of the 9th transmit clock pulse. Read the ACKBR bit in ICIER, and confirm that the slave device has been selected. Then, write second byte data to ICDRT. When ACKBR is 1, the slave device has not been acknowledged, so issue the stop condition. To issue the stop condition, write 0 to BBSY and SCP using MOV instruction. SCL is fixed low until the transmit data is prepared or the stop condition is issued. 5. The transmit data after the second byte is written to ICDRT every time TDRE is set. 6. Write the number of bytes to be transmitted to ICDRT. Wait until TEND is set (the end of last byte data transmission) while TDRE is 1, or wait for NACK (NACKF in ICSR = 1) from the receive device while ACKE in ICIER is 1. Then, issue the stop condition to clear TEND or NACKF. 7. When the STOP bit in ICSR is set to 1, the operation returns to the slave receive mode. Rev. 1.00, 11/03, page 239 of 376 SCL (Master output) SDA (Master output) 1 Bit 7 2 Bit 6 3 Bit 5 4 Bit 4 5 Bit 3 6 Bit 2 7 Bit 1 8 Bit 0 R/ 9 1 Bit 7 2 Bit 6 Slave address SDA (Slave output) TDRE A TEND ICDRT Address + R/ Data 1 Data 2 ICDRS Address + R/ Data 1 User processing [2] Instruction of start condition issuance [4] Write data to ICDRT (second byte) [3] Write data to ICDRT (first byte) [5] Write data to ICDRT (third byte) Figure 15.5 Master Transmit Mode Operation Timing (1) SCL (Master output) SDA (Master output) SDA (Slave output) TDRE A 9 1 Bit 7 2 Bit 6 3 Bit 5 4 Bit 4 5 Bit 3 6 Bit 2 7 Bit 1 8 Bit 0 9 A/ TEND ICDRT Data n ICDRS Data n User [5] Write data to ICDRT processing [6] Issue stop condition. Clear TEND. [7] Set slave receive mode Figure 15.6 Master Transmit Mode Operation Timing (2) Rev. 1.00, 11/03, page 240 of 376 15.4.3 Master Receive Operation In master receive mode, the master device outputs the receive clock, receives data from the slave device, and returns an acknowledge signal. For master receive mode operation timing, refer to figures 15.7 and 15.8. The reception procedure and operations in master receive mode are shown below. 1. Clear the TEND bit in ICSR to 0, then clear the TRS bit in ICCR1 to 0 to switch from master transmit mode to master receive mode. Then, clear the TDRE bit to 0. 2. When ICDRR is read (dummy data read), reception is started, and the receive clock is output, and data received, in synchronization with the internal clock. The master device outputs the level specified by ACKBT in ICIER to SDA, at the 9th receive clock pulse. 3. After the reception of first frame data is completed, the RDRF bit in ICST is set to 1 at the rise of 9th receive clock pulse. At this time, the receive data is read by reading ICDRR, and RDRF is cleared to 0. 4. The continuous reception is performed by reading ICDRR every time RDRF is set. If 8th receive clock pulse falls after reading ICDRR by the other processing while RDRF is 1, SCL is fixed low until ICDRR is read. 5. If next frame is the last receive data, set the RCVD bit in ICCR1 to 1 before reading ICDRR. This enables the issuance of the stop condition after the next reception. 6. When the RDRF bit is set to 1 at rise of the 9th receive clock pulse, issue the stage condition. 7. When the STOP bit in ICSR is set to 1, read ICDRR. Then clear the RCVD bit to 0. 8. The operation returns to the slave receive mode. Rev. 1.00, 11/03, page 241 of 376 Master transmit mode SCL (Master output) SDA (Master output) SDA (Slave output) TDRE A 9 1 Master receive mode 2 3 4 5 6 7 8 9 A 1 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Bit 7 TEND TRS RDRF ICDRS Data 1 ICDRR User processing Data 1 [3] Read ICDRR [1] Clear TDRE after clearing TEND and TRS [2] Read ICDRR (dummy read) Figure 15.7 Master Receive Mode Operation Timing (1) SCL (Master output) SDA (Master output) SDA (Slave output) RDRF 9 A 1 2 3 4 5 6 7 8 9 A/ Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 RCVD ICDRS Data n-1 Data n ICDRR User processing Data n-1 Data n [5] Read ICDRR after setting RCVD [7] Read ICDRR, and clear RCVD [6] Issue stop condition [8] Set slave receive mode Figure 15.8 Master Receive Mode Operation Timing (2) Rev. 1.00, 11/03, page 242 of 376 15.4.4 Slave Transmit Operation In slave transmit mode, the slave device outputs the transmit data, while the master device outputs the receive clock and returns an acknowledge signal. For slave transmit mode operation timing, refer to figures 15.9 and 15.10. The transmission procedure and operations in slave transmit mode are described below. 1. Set the ICE bit in ICCR1 to 1. Set the MLS and WAIT bits in ICMR and the CKS3 to CKS0 bits in ICCR1 to 1. (Initial setting) Set the MST and TRS bits in ICCR1 to select slave receive mode, and wait until the slave address matches. 2. When the slave address matches in the first frame following detection of the start condition, the slave device outputs the level specified by ACKBT in ICIER to SDA, at the rise of the 9th clock pulse. At this time, if the 8th bit data (R/W) is 1, the TRS and ICSR bits in ICCR1 are set to 1, and the mode changes to slave transmit mode automatically. The continuous transmission is performed by writing transmit data to ICDRT every time TDRE is set. 3. If TDRE is set after writing last transmit data to ICDRT, wait until TEND in ICSR is set to 1, with TDRE = 1. When TEND is set, clear TEND. 4. Clear TRS for the end processing, and read ICDRR (dummy read). SCL is free. 5. Clear TDRE. Slave receive mode SCL (Master output) SDA (Master output) SCL (Slave output) SDA (Slave output) TDRE TEND TRS ICDRT Data 1 Data 2 Data 3 A Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Bit 7 Slave transmit mode 9 1 2 3 4 5 6 7 8 9 A 1 ICDRS Data 1 Data 2 ICDRR User processing [2] Write data to ICDRT (data 1) [2] Write data to ICDRT (data 2) [2] Write data to ICDRT (data 3) Figure 15.9 Slave Transmit Mode Operation Timing (1) Rev. 1.00, 11/03, page 243 of 376 Slave receive mode Slave transmit mode SCL (Master output) SDA (Master output) SCL (Slave output) SDA (Slave output) TDRE TEND TRS ICDRT ICDRS ICDRR User processing 9 A 1 2 3 4 5 6 7 8 9 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Data n [3] Clear TEND [4] Read ICDRR (dummy read) after clearing TRS [5] Clear TDRE Figure 15.10 Slave Transmit Mode Operation Timing (2) 15.4.5 Slave Receive Operation In slave receive mode, the master device outputs the transmit clock and transmit data, and the slave device returns an acknowledge signal. For slave receive mode operation timing, refer to figures 15.11 and 15.12. The reception procedure and operations in slave receive mode are described below. 1. Set the ICE bit in ICCR1 to 1. Set the MLS and WAIT bits in ICMR and the CKS3 to CKS0 bits in ICCR1 to 1. (Initial setting) Set the MST and TRS bits in ICCR1 to select slave receive mode, and wait until the slave address matches. 2. When the slave address matches in the first frame following detection of the start condition, the slave device outputs the level specified by ACKBT in ICIER to SDA, at the rise of the 9th clock pulse. At the same time, RDRF in ICSR is set to read ICDRR (dummy read). (Since the read data show the slave address and R/W, it is not used.) 3. Read ICDRR every time RDRF is set. If 8th receive clock pulse falls while RDRF is 1, SCL is fixed low until ICDRR is read. The change of the acknowledge before reading ICDRR, to be returned to the master device, is reflected to the next transmit frame. 4. The last byte data is read by reading ICDRR. Rev. 1.00, 11/03, page 244 of 376 SCL (Master output) SDA (Master output) SCL (Slave output) SDA (Slave output) RDRF 9 1 2 3 4 5 6 7 8 9 1 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Bit 7 A A ICDRS Data 1 Data 2 ICDRR User processing Data 1 [2] Read ICDRR (dummy read) [2] Read ICDRR Figure 15.11 Slave Receive Mode Operation Timing (1) SCL (Master output) SDA (Master output) SCL (Slave output) SDA (Slave output) 9 1 Bit 7 2 Bit 6 3 Bit 5 4 Bit 4 5 Bit 3 6 Bit 2 7 Bit 1 8 Bit 0 9 A A RDRF ICDRS Data 1 Data 2 ICDRR User processing Data 1 [3] Set ACKBT [3] Read ICDRR [4] Read ICDRR Figure 15.12 Slave Receive Mode Operation Timing (2) Rev. 1.00, 11/03, page 245 of 376 15.4.6 Clocked Synchronous Serial Format This module can be operated with the clocked synchronous serial format, by setting the FS bit in SAR to 1. When the MST bit in ICCR1 is 1, the transfer clock output from SCL is selected. When MST is 0, the external clock input is selected. Data Transfer Format: Figure 15.13 shows the clocked synchronous serial transfer format. The transfer data is output from the rise to the fall of the SCL clock, and the data at the rising edge of the SCL clock is guaranteed. The MLS bit in ICMR sets the order of data transfer, in either the MSB first or LSB first. The output level of SDA can be changed during the transfer wait, by the SDAO bit in ICCR2. SCL SDA Bit 0 Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7 Figure 15.13 Clocked Synchronous Serial Transfer Format Transmit Operation: In transmit mode, transmit data is output from SDA, in synchronization with the fall of the transfer clock. The transfer clock is output when MST in ICCR1 is 1, and is input when MST is 0. For transmit mode operation timing, refer to figure 15.14. The transmission procedure and operations in transmit mode are described below. 1. Set the ICE bit in ICCR1 to 1. Set the MST and CKS3 to CKS0 bits in ICCR1 to 1. (Initial setting) 2. Set the TRS bit in ICCR1 to select the transmit mode. Then, TDRE in ICSR is set. 3. Confirm that TDRE has been set. Then, write the transmit data to ICDRT. The data is transferred from ICDRT to ICDRS, and TDRE is set automatically. The continuous transmission is performed by writing data to ICDRT every time TDRE is set. When changing from transmit mode to receive mode, clear TRS while TDRE is 1. Rev. 1.00, 11/03, page 246 of 376 SCL SDA (Output) TRS TDRE ICDRT ICDRS 1 2 7 Bit 6 8 Bit 7 1 Bit 0 7 Bit 6 8 Bit 7 1 Bit 0 Bit 0 Bit 1 Data 1 Data 1 Data 2 Data 2 Data 3 Data 3 User processing [3] Write data [3] Write data to ICDRT to ICDRT [2] Set TRS [3] Write data to ICDRT [3] Write data to ICDRT Figure 15.14 Transmit Mode Operation Timing Receive Operation: In receive mode, data is latched at the rise of the transfer clock. The transfer clock is output when MST in ICCR1 is 1, and is input when MST is 0. For receive mode operation timing, refer to figure 15.15. The reception procedure and operations in receive mode are described below. 1. Set the ICE bit in ICCR1 to 1. Set the MST and CKS3 to CKS0 bits in ICCR1 to 1. (Initial setting) 2. When the transfer clock is output, set MST to 1 to start outputting the receive clock. 3. When the receive operation is completed, data is transferred from ICDRS to ICDRR and RDRF in ICSR is set. When MST = 1, the next byte can be received, so the clock is continually output. The continuous reception is performed by reading ICDRR every time RDRF is set. When the 8th clock is risen while RDRF is 1, the overrun is detected and AL/OVE in ICSR is set. At this time, the previous reception data is retained in ICDRR. 4. To stop receiving when MST = 1, set RCVD in ICCR1 to 1, then read ICDRR. Then, SCL is fixed high after receiving the next byte data. Rev. 1.00, 11/03, page 247 of 376 SCL SDA (Input) MST TRS 1 2 7 Bit 6 8 Bit 7 1 Bit 0 7 Bit 6 8 Bit 7 1 2 Bit 0 Bit 0 Bit 1 RDRF ICDRS ICDRR User processing [2] Set MST (when outputting the clock) Data 1 Data 2 Data 3 Data 1 Data 2 [3] Read ICDRR [3] Read ICDRR Figure 15.15 Receive Mode Operation Timing 15.4.7 Noise Canceler The logic levels at the SCL and SDA pins are routed through the noise canceler before being latched internally. Figure 15.16 shows a block diagram of the noise canceler. The noise canceler consists of two cascaded latches and a match detector. The SCL (or SDA) input signal is sampled on the system clock, but is not passed forward to the next circuit unless the outputs of both latches agree. If they do not agree, the previous value is held. Sampling clock C SCL or SDA input signal D Latch Q D C Q Latch March detector Internal SCL or SDA signal System clock period Sampling clock Figure 15.16 Block Diagram of Noise Canceler Rev. 1.00, 11/03, page 248 of 376 15.4.8 Example of Use Flowcharts in respective modes that use the I2C bus interface are shown in figures 15.17 to 15.20. Start Initialize Read BBSY in ICCR2 No BBSY=0 ? Yes Set MST and TRS in ICCR1 to 1. Write 1 to BBSY and 0 to SCP. Write transmit data in ICDRT Read TEND in ICSR No TEND=1 ? Yes Read ACKBR in ICIER ACKBR=0 ? No [1] [3] Issue the start candition. [2] [4] Set the first byte (slave address + R/ ) of transmit data. [3] [5] Wait for 1 byte to be transmitted. [4] [6] Test the acknowledge transferred from the specified slave device. [7] Set the second and subsequent bytes (except for the final byte) of transmit data. [5] [8] Wait for ICDRT empty. [9] Set the last byte of transmit data. [6] [10] Wait for last byte to be transmitted. [11] Clear the TEND flag. Mater receive mode [7] [12] Clear the STOP flag. [13] Issue the stop condition. [8] [14] Wait for the creation of stop condition. [15] Set slave receive mode. Clear TDRE. [9] [1] Test the status of the SCL and SDA lines. [2] Set master transmit mode. Yes No Transmit mode? Yes Write transmit data in ICDRT Read TDRE in ICSR No TDRE=1 ? Yes No Last byte? Yes Write transmit data in ICDRT Read TEND in ICSR No [10] TEND=1 ? Yes Clear TEND in ICSR Clear STOP in ICSR Write 0 to BBSY and SCP Read STOP in ICSR [11] [12] [13] No [14] STOP=1 ? Yes Set MST to 1 and TRS to 0 in ICCR1 Clear TDRE in ICSR End [15] Figure 15.17 Sample Flowchart for Master Transmit Mode Rev. 1.00, 11/03, page 249 of 376 Mater receive mode [1] Clear TEND, select master receive mode, and then clear TDRE.* Clear TEND in ICSR Clear TRS in ICCR1 to 0 Clear TDRE in ICSR Clear ACKBT in ICIER to 0 Dummy-read ICDRR Read RDRF in ICSR No RDRF=1 ? Yes Last receive - 1? No Read ICDRR Yes [5] [6] [2] [3] [1] [2] Set acknowledge to the transmit device.* [3] Dummy-read ICDDR.* [4] Wait for 1 byte to be received [5] Check whether it is the (last receive - 1). [6] Read the receive data last. [4] [7] Set acknowledge of the final byte. Disable continuous reception (RCVD = 1). [8] Read the (final byte - 1) of receive data. [9] Wait for the last byte to be receive. [10] Clear the STOP flag. [11] Issue the stop condition. Set ACKBT in ICIER to 1 [7] Set RCVD in ICCR1 to 1 Read ICDRR Read RDRF in ICSR No RDRF=1 ? [9] [8] [12] Wait for the creation of stop condition. [13] Read the last byte of receive data. [14] Clear RCVD. [15] Set slave receive mode. Yes Clear STOP in ICSR. Write 0 to BBSY and SCP Read STOP in ICSR No STOP=1 ? Yes Read ICDRR Clear RCVD in ICCR1 to 0 Clear MST in ICCR1 to 0 End [10] [11] [12] [13] [14] [15] Note: Do not activate an interrupt during the execution of steps [1] to [3]. When one byte is received, steps [2] to [6] are skipped after step [1], before jumping to step [7]. The step [8] is dammy-read in ICDRR. Figure 15.18 Sample Flowchart for Master Receive Mode Rev. 1.00, 11/03, page 250 of 376 Slave transmit mode Clear AAS in ICSR Write transmit data in ICDRT Read TDRE in ICSR No [3] TDRE=1 ? Yes No Last byte? Yes Write transmit data in ICDRT Read TEND in ICSR No [5] TEND=1 ? Yes Clear TEND in ICSR Clear TRS in ICCR1 to 0 Dummy read ICDRR Clear TDRE in ICSR End [4] [1] [1] Clear the AAS flag. [2] Set transmit data for ICDRT (except for the last data). [3] Wait for ICDRT empty. [2] [4] Set the last byte of transmit data. [5] Wait for the last byte to be transmitted. [6] Clear the TEND flag . [7] Set slave receive mode. [8] Dummy-read ICDRR to release the SCL line. [9] Clear the TDRE flag. [6] [7] [8] [9] Figure 15.19 Sample Flowchart for Slave Transmit Mode Rev. 1.00, 11/03, page 251 of 376 Slave receive mode [1] Clear the AAS flag. Clear AAS in ICSR Clear ACKBT in ICIER to 0 Dummy-read ICDRR [1] [2] Set acknowledge to the transmit device. [2] [3] [3] Dummy-read ICDRR. [4] Wait for 1 byte to be received. [5] Check whether it is the (last receive - 1). Read RDRF in ICSR No RDRF=1 ? Yes Last receive - 1? No Read ICDRR Yes [8] Read the (last byte - 1) of receive data. [5] [9] Wait the last byte to be received. [6] [10] Read for the last byte of receive data. [4] [6] Read the receive data. [7] Set acknowledge of the last byte. Set ACKBT in ICIER to 1 [7] Read ICDRR Read RDRF in ICSR No [8] [9] RDRF=1 ? Yes Read ICDRR End [10] Note: When one byte is received, steps [2] to [6] are skipped after step [1], before jumping to step [7]. The step [8] is dammy-read in ICDRR. Figure 15.20 Sample Flowchart for Slave Receive Mode Rev. 1.00, 11/03, page 252 of 376 15.5 Interrupts There are six interrupt requests in this module; transmit data empty, transmit end, receive data full, NACK receive, STOP recognition, and arbitration lost/overrun error. Table 15.3 shows the contents of each interrupt request. Table 15.3 Interrupt Requests Clocked Synchronous 2 I C Mode Mode ! ! ! ! * Interrupt Request Transmit Data Empty Transmit End Receive Data Full STOP Recognition NACK Receive Arbitration Lost/Overrun Error Abbreviation TXI TEI RXI STPI NAKI Interrupt Condition (TDRE=1) * (TIE=1) (TEND=1) * (TEIE=1) (RDRF=1) * (RIE=1) (STOP=1) * (STIE=1) {(NACKF=1)+(AL=1)} (NAKIE=1) ! ! ! x x ! ! ! When interrupt conditions described in table 15.3 are 1 and the I bit in CCR is 0, the CPU executes an interrupt exception processing. Interrupt sources should be cleared in the exception processing. TDRE and TEND are automatically cleared to 0 by writing the transmit data to ICDRT. RDRF are automatically cleared to 0 by reading ICDRR. TDRE is set to 1 again at the same time when transmit data is written to ICDRT. When TDRE is cleared to 0, then an excessive data of one byte may be transmitted. Rev. 1.00, 11/03, page 253 of 376 15.6 Bit Synchronous Circuit In master mode, this module has a possibility that high level period may be short in the two states described below. * When SCL is driven to low by the slave device * When the rising speed of SCL is lowered by the load of the SCL line (load capacitance or pullup resistance) Therefore, it monitors SCL and communicates by bit with synchronization. Figure 15.21 shows the timing of the bit synchronous circuit and table 15.4 shows the time when SCL output changes from low to Hi-Z then SCL is monitored. SCL monitor timing reference clock SCL VIH Internal SCL Figure 15.21 Timing of Bit Synchronous Circuit Table 15.4 Time for Monitoring SCL CKS3 0 1 CKS2 0 1 0 1 Time for Monitoring SCL 7.5 tcyc 19.5 tcyc 17.5 tcyc 41.5 tcyc Rev. 1.00, 11/03, page 254 of 376 Section 16 A/D Converter This LSI includes a successive approximation type 10-bit A/D converter that allows up to four analog input channels to be selected. The block diagram of the A/D converter is shown in figure 16.1. 16.1 Features * 10-bit resolution * Four input channels * Conversion time: At least 7 s per channel (at 10 MHz operation) * Two operating modes Single mode: Single-channel A/D conversion Scan mode: Continuous A/D conversion on 1 to 4 channels * Four data registers Conversion results are held in a 16-bit data register for each channel * Sample and hold function * Two conversion start methods Software External trigger signal * Interrupt request An A/D conversion end interrupt request (ADI) can be generated ADCMS32A_000020020200 Rev. 1.00, 11/03, page 255 of 376 AVCC 10-bit D/A Successive approximations register A D D R A A D D R B A D D R C A D D R D A D C S R A D C R Analog multiplexer + Control circuit Comparator Sample-andhold circuit Bus interface Module data bus Internal data bus /4 /8 AN0 AN1 AN2 AN3 ADI interrupt request [Legend] ADCR: ADCSR: ADDRA: ADDRB: ADDRC: ADDRD: A/D control register A/D control/status register A/D data register A A/D data register B A/D data register C A/D data register D Figure 16.1 Block Diagram of A/D Converter Rev. 1.00, 11/03, page 256 of 376 16.2 Input/Output Pins Table 16.1 summarizes the input pins used by the A/D converter. Table 16.1 Pin Configuration Pin Name Analog power supply pin Analog input pin 0 Analog input pin 1 Analog input pin 2 Analog input pin 3 A/D external trigger input pin Symbol AVCC AN0 AN1 AN2 AN3 ADTRG I/O Input Input Input Input Input Input External trigger input pin for starting A/D conversion Function Analog block power supply pin Analog input pins 16.3 Register Description The A/D converter has the following registers. * A/D data register A (ADDRA) * A/D data register B (ADDRB) * A/D data register C (ADDRC) * A/D data register D (ADDRD) * A/D control/status register (ADCSR) * A/D control register (ADCR) 16.3.1 A/D Data Registers A to D (ADDRA to ADDRD) There are four 16-bit read-only ADDR registers; ADDRA to ADDRD, used to store the results of A/D conversion. The ADDR registers, which store a conversion result for each channel, are shown in table 16.2. The converted 10-bit data is stored in bits 6 to 15. The lower 6 bits are always read as 0. The data bus between the CPU and the A/D converter is 8 bits wide. The upper byte can be read directly from the CPU, however the lower byte should be read via a temporary register. The temporary register contents are transferred from the ADDR when the upper byte data is read. When reading ADDR, read the upper bytes only or read in word units. ADDR is initialized to H'0000. Rev. 1.00, 11/03, page 257 of 376 Table 16.2 Analog Input Channels and Corresponding ADDR Registers Analog Input Channel AN0 AN1 AN2 AN3 A/D Data Register to Be Stored Results of A/D Conversion ADDRA ADDRB ADDRC ADDRD 16.3.2 A/D Control/Status Register (ADCSR) ADCSR consists of the control bits and conversion end status bits of the A/D converter. Bit 7 Bit Name ADF Initial Value 0 R/W R/W Description A/D End Flag [Setting conditions] * * When A/D conversion ends in single mode When A/D conversion ends on all the channels selected in scan mode When 0 is written after reading ADF = 1 [Clearing conditions] * 6 ADIE 0 R/W A/D Interrupt Enable A/D conversion end interrupt (ADI) request enabled by ADF when 1 is set 5 ADST 0 R/W A/D Start Setting this bit to 1 starts A/D conversion. In single mode, this bit is cleared to 0 automatically when conversion on the specified channel is complete. In scan mode, conversion continues sequentially on the specified channels until this bit is cleared to 0 by software, a reset, or a transition to standby mode. 4 SCAN 0 R/W Scan Mode Selects single mode or scan mode as the A/D conversion operating mode. 0: Single mode 1: Scan mode Rev. 1.00, 11/03, page 258 of 376 Bit 3 Bit Name CKS Initial Value 0 R/W R/W Description Clock Select Selects the A/D conversions time 0: Conversion time = 134 states (max.) 1: Conversion time = 70 states (max.) Clear the ADST bit to 0 before switching the conversion time. 2 1 0 CH2 CH1 CH0 0 0 0 R/W R/W R/W Channel Select 0 to 2 Select analog input channels. When SCAN = 0 000: AN0 001: AN1 010: AN2 011: AN3 When SCAN = 1 000: AN0 001: AN0 to AN1 010: AN0 to AN2 011: AN0 to AN3 Note: When executing the A/D conversion through AN3 or AN2, do not set the VDDII bit in LVDCR to 0. If 0 is set, the A/D conversion accuracy is not guaranteed. 16.3.3 A/D Control Register (ADCR) ADCR enables A/D conversion started by an external trigger signal. Bit 7 Bit Name TRGE Initial Value 0 R/W R/W Description Trigger Enable A/D conversion is started at the falling edge and the rising edge of the external trigger signal (ADTRG) when this bit is set to 1. The selection between the falling edge and rising edge of the external trigger pin (ADTRG) conforms to the WPEG5 bit in the interrupt edge select register 2 (IEGR2) 6 to 4 3, 2 -- -- All 1 All 0 -- R/W Reserved These bits are always read as 1. Reserved Although these bits are readable/writable, they should not be set to 1. Rev. 1.00, 11/03, page 259 of 376 Bit 1 0 Bit Name -- -- Initial Value 1 0 R/W R/W R/W Description Reserved This bit is always read as 1. Reserved Although this bit is readable/writable, it should not be set to 1. Rev. 1.00, 11/03, page 260 of 376 16.4 Operation The A/D converter operates by successive approximation with 10-bit resolution. It has two operating modes; single mode and scan mode. When changing the operating mode or analog input channel, in order to prevent incorrect operation, first clear the bit ADST to 0 in ADCSR. The ADST bit can be set at the same time as the operating mode or analog input channel is changed. 16.4.1 Single Mode In single mode, A/D conversion is performed once for the analog input on the specified single channel as follows: 1. 2. 3. 4. A/D conversion is started from the first channel when the ADST bit in ADCSR is set to 1, according to software or external trigger input. When A/D conversion is completed, the result is transferred to the corresponding A/D data register to the channel. On completion of conversion, the ADF bit in ADCSR is set to 1. If the ADIE bit is set to 1 at this time, an ADI interrupt request is generated. The ADST bit remains set to 1 during A/D conversion. When A/D conversion ends, the ADST bit is automatically cleared to 0 and the A/D converter enters the wait state. Scan Mode 16.4.2 In scan mode, A/D conversion is performed sequentially for the analog input on the specified channels (four channels maximum) as follows: 1. When the ADST bit is set to 1 by software, or external trigger input, A/D conversion starts on the first channel in the group. 2. When A/D conversion for each channel is completed, the result is sequentially transferred to the A/D data register corresponding to each channel. 3. When conversion of all the selected channels is completed, the ADF flag in ADCSR is set to 1. If the ADIE bit is set to 1 at this time, an ADI interrupt is requested. Conversion of the first channel in the group starts again. 4. The ADST bit is not automatically cleared to 0. Steps [2] to [3] are repeated as long as the ADST bit remains set to 1. When the ADST bit is cleared to 0, A/D conversion stops. Rev. 1.00, 11/03, page 261 of 376 16.4.3 Input Sampling and A/D Conversion Time The A/D converter has a built-in sample-and-hold circuit. The A/D converter samples the analog input when the A/D conversion start delay time (tD) has passed after the ADST bit is set to 1, then starts conversion. Figure 16.2 shows the A/D conversion timing. Table 16.3 shows the A/D conversion time. As indicated in figure 16.2, the A/D conversion time includes tD and the input sampling time. The length of tD varies depending on the timing of the write access to ADCSR. The total conversion time therefore varies within the ranges indicated in table 16.3. In scan mode, the values given in table 16.3 apply to the first conversion time. In the second and subsequent conversions, the conversion time is 128 states (fixed) when CKS = 0 and 66 states (fixed) when CKS = 1. (1) Address (2) Write signal Input sampling timing ADF tD tSPL tCONV [Legend] (1): ADCSR write cycle (2): ADCSR address A/D conversion start delay tD: tSPL: Input sampling time tCONV: A/D conversion time Figure 16.2 A/D Conversion Timing Rev. 1.00, 11/03, page 262 of 376 Table 16.3 A/D Conversion Time (Single Mode) CKS = 0 Item Input sampling time A/D conversion time Symbol tSPL tCONV Min. 6 -- 131 Typ. -- 31 -- Max. 9 -- 134 Min. 4 -- 69 A/D conversion start delay tD CKS = 1 Typ. -- 15 -- Max. 5 -- 70 Note: All values represent the number of states. 16.4.4 External Trigger Input Timing A/D conversion can also be started by an external trigger input. When the TRGE bit is set to 1 in ADCR, external trigger input is enabled at the ADTRG pin. A falling edge at the ADTRG input pin sets the ADST bit to 1 in ADCSR, starting A/D conversion. Other operations, in both single and scan modes, are the same as when the bit ADST has been set to 1 by software. Figure 16.3 shows the timing. Internal trigger signal ADST A/D conversion Figure 16.3 External Trigger Input Timing Rev. 1.00, 11/03, page 263 of 376 16.5 A/D Conversion Accuracy Definitions This LSI's A/D conversion accuracy definitions are given below. * Resolution The number of A/D converter digital output codes * Quantization error The deviation inherent in the A/D converter, given by 1/2 LSB (see figure 16.4). * Offset error The deviation of the analog input voltage value from the ideal A/D conversion characteristic when the digital output changes from the minimum voltage value 0000000000 to 0000000001 (see figure 16.5). * Full-scale error The deviation of the analog input voltage value from the ideal A/D conversion characteristic when the digital output changes from 1111111110 to 1111111111 (see figure 16.5). * Nonlinearity error The error with respect to the ideal A/D conversion characteristics between zero voltage and full-scale voltage. Does not include offset error, full-scale error, or quantization error. * Absolute accuracy The deviation between the digital value and the analog input value. Includes offset error, fullscale error, quantization error, and nonlinearity error. Digital output 111 110 101 100 011 010 001 000 1 8 Ideal A/D conversion characteristic Quantization error 2 8 3 8 4 8 5 8 6 8 7 FS 8 Analog input voltage Figure 16.4 A/D Conversion Accuracy Definitions (1) Rev. 1.00, 11/03, page 264 of 376 Digital output Full-scale error Ideal A/D conversion characteristic Nonlinearity error Actual A/D conversion characteristic FS Analog input voltage Offset error Figure 16.5 A/D Conversion Accuracy Definitions (2) Rev. 1.00, 11/03, page 265 of 376 16.6 16.6.1 Usage Notes Permissible Signal Source Impedance This LSI's analog input is designed such that conversion accuracy is guaranteed for an input signal for which the signal source impedance is 5 k or less. This specification is provided to enable the A/D converter's sample-and-hold circuit input capacitance to be charged within the sampling time; if the sensor output impedance exceeds 5 k, charging may be insufficient and it may not be possible to guarantee A/D conversion accuracy. However, for A/D conversion in single mode with a large capacitance provided externally, the input load will essentially comprise only the internal input resistance of 10 k, and the signal source impedance is ignored. However, as a low-pass filter effect is obtained in this case, it may not be possible to follow an analog signal with a large differential coefficient (e.g., 5 mV/s or greater) (see figure 16.6). When converting a high-speed analog signal or converting in scan mode, a low-impedance buffer should be inserted. 16.6.2 Influences on Absolute Accuracy Adding capacitance results in coupling with GND, and therefore noise in GND may adversely affect absolute accuracy. Be sure to make the connection to an electrically stable GND. Care is also required to ensure that filter circuits do not interfere with digital signals or act as antennas on the mounting board. This LSI Sensor output impedance to 5 k Sensor input Low-pass filter C to 0.1 F Cin = 15 pF A/D converter equivalent circuit 10 k 20 pF Figure 16.6 Analog Input Circuit Example Rev. 1.00, 11/03, page 266 of 376 Section 17 Band-Gap Circuit, Power-On Reset, and Low-Voltage Detection Circuits This LSI can include a band-gap circuit (BGR, band-gap regulator), a power-on reset circuit and low-voltage detection circuit. BGR supplies a reference voltage to the internal RC oscillator and low-voltage detection circuit. Figure 17.1 shows the block diagram of how BGR is allocated. The low-voltage detection (LVD) circuit consists of two circuits: LVDI (interrupt by low voltage detection) and LVDR (reset by low voltage detection) circuits. This circuit is used to prevent abnormal operation (program runaway) from occurring due to the power supply voltage fall and to recreate the state before the power supply voltage fall when the power supply voltage rises again. Even if the power supply voltage falls, the unstable state when the power supply voltage falls below the guaranteed operating voltage can be removed by entering standby mode when exceeding the guaranteed operating voltage and during normal operation. Thus, system stability can be improved. If the power supply voltage falls more, the reset state is automatically entered. If the power supply voltage rises again, the reset state is held for a specified period, then active mode is automatically entered. Figure 17.2 is a block diagram of the power-on reset circuit and the low-voltage detection circuit. LVI0000A_000020030300 Rev. 1.00, 11/03, page 267 of 376 17.1 Features * BGR circuit Supplies stable reference voltage covering the entire operating voltage range and the operating temperature range. Reduces power consumption when BGR is disabled by setting registers. * Power-on reset circuit Uses an external capacitor to generate an internal reset signal when power is first supplied. * Low-voltage detection circuit LVDR: Monitors the power-supply voltage, and generates an internal reset signal when the voltage falls below a given value. LVDI: Monitors the power-supply voltage, and generates an interrupt when the voltage falls below or rises above respective given values. Two detection levels for reset generation voltage are available: when only the LVDR circuit is used, or when the LVDI and LVDR circuits are both used. VCLSEL Vcc Step-down circuit VCL Internal RC oscillator BGRE BGR VBGR RCSTP LVDE [Legend] Vcc: BGRE: VCL: VBGR: VCLSEL: RCSTP: LVDE: LVD (low-voltage detection circuit) Power supply BGR circuit enable signal Internal power supply generated from Vcc by the step-down circuit Reference voltage from BGR Select signal for the source of the RC oscillator power supply RC oscillator stop signal LVD enable signal Figure 17.1 Block Diagram around BGR Rev. 1.00, 11/03, page 268 of 376 OVF CK PSS R R Internal reset signal Noise filter circuit Noise filter circuit External power supply Vcc Ladder network Vreset VintU VintD Q S Power-on reset circuit LVDCR Internal data bus ExtD Interrupt control circuit ExtU VDDII VBGR [Legend] PSS: LVDCR: LVDSR: VBGR: ExtD: ExtU: VDDII: Prescaler S Low-voltage-detection control register Low-voltage-detection status register Reference voltage from BGR Compared voltage for falling external input voltage Compared voltage for rising external input voltage Bit 5 in LVDCR LVDSR Interrupt request Figure 17.2 Block Diagram of Power-On Reset Circuit and Low-Voltage Detection Circuit 17.2 Register Descriptions The low-voltage detection circuit has the following registers. * Low-voltage-detection control register (LVDCR) * Low-voltage-detection status register (LVDSR) 17.2.1 Low-Voltage-Detection Control Register (LVDCR) LVDCR enables or disables the low-voltage detection circuit and BGR circuit, selects the compared voltage of the LVDI circuit, sets the detection levels for the LVDR circuit, enables or disables the LVDR circuit, and enables or disables generation of an interrupt when the powersupply voltage rises above or falls below the respective levels. Table 17.1 shows the relationship between the LVDCR settings and functions to be selected. LVDCR should be set according to table 17.1. Rev. 1.00, 11/03, page 269 of 376 Bit 7 Bit Name LVDE Initial Value 1* R/W R/W Description LVD Enable 0: Low-voltage detection circuit is not used (standby mode) 1: Low-voltage detection circuit is used 6 BGRE 1* R/W BGR Enable 0: BGR circuit is not used (standby mode) 1: BGR circuit is used 5 VDDII 1* R/W LVDR External Compared Voltage Input Inhibit 0: Use external voltage as LVDI compared voltage 1: Use internal voltage as LVDI compared voltage 4 3 LVDSEL 1 0* R/W Reserved This bit is always read as 1 and cannot be modified. LVDR Detection Level Select 0: Reset detection voltage is 2.3 V (Typ.) 1: Reset detection voltage is 3.6 V (Typ.) When the falling or rising voltage detection interrupt is used, the reset detection voltage of 2.3 V (Typ.) should be used. When only a reset detection interrupt is used, reset detection voltage of 3.6 V (Typ.) should be used. 2 LVDRE 1* R/W LVDR Enable 0: Disables an LVDR 1: Enables an LVDR 1 LVDDE 0 R/W Voltage-Fall-Interrupt Enable 0: Interrupt on the power-supply voltage falling disabled 1: Interrupt on the power-supply voltage falling enabled 0 LVDUE 0 R/W Voltage-Rise-Interrupt Enable 0: Interrupt on the power-supply voltage rising disabled 1: Interrupt on the power-supply voltage rising enabled Note: * Not initialized by an LVDR but initialized by a power-on reset or a watchdog timer reset. Rev. 1.00, 11/03, page 270 of 376 Table 17.1 LVDCR Settings and Select Functions LVDCR Settings Select Functions LowVoltageDetection Fall Interrupt LowVoltageDetection Rise Interrupt LVDE BGRE VDDII LVDSEL LVDRE LVDDE LVDUE Power-On Reset LVDR 0 1 1 1 1 * 1 * 2 1 1 1 1 * 2 * 2 * 2 * 2 1 1 1 1 * * * * 1 0 0 0 1 0 0 1 0 1 1 1 0 0 1 1 Notes: 1. Set these bits if necessary. 2. Settings are ignored. 17.2.2 Low-Voltage-Detection Status Register (LVDSR) LVDSR indicates whether the power-supply voltage falls below or rises above the respective given values. Bit 7 to 2 1 Bit Name LVDDF Initial Value All 1 0* R/W R/W Description Reserved These bits are always read as 1 and cannot be modified. LVD Power-Supply Voltage Fall Flag [Setting condition] When the power-supply voltage falls below Vint (D) (Typ. = 3.7 V) [Clearing condition] When writing 0 to this bit after reading it as 1 0 LVDUF 0* R/W LVD Power-Supply Voltage Rise Flag [Setting condition] When the power supply voltage falls below Vint (D) while the LVDUE bit in LVDCR is set to 1 and then rises above Vint (U) (Typ. = 4.0 V) before falling below Vreset1 (Typ. = 2.3 V) [Clearing condition] When writing 0 to this bit after reading it as 1 Note: * Initialized by an LVDR. Rev. 1.00, 11/03, page 271 of 376 17.3 17.3.1 Operations Power-On Reset Circuit Figure 17.3 shows the timing of the operation of the power-on reset circuit. As the power-supply voltage rises, the capacitor which is externally connected to the RES pin is gradually charged via the internal pull-up resistor (Typ. 150 k). While the RES signal is driven low, the prescaler S and the entire chip retains the reset state. When the level on the RES signal reaches the specified value, the prescaler S is released from its reset state and it starts counting. The OVF signal is generated to release the internal reset signal after the prescaler S has counted 131,072 cycles of the clock. The noise filter circuit which removes noise with less than 400 ns (Typ.) is included to prevent the incorrect operation of this LSI caused by noise on the RES signal. To achieve stable operation of this LSI, the power supply needs to rise to its full level and settles within the specified time. The maximum time required for the power supply to rise and settle (tPWON) is determined by the oscillation frequency (fOSC) and capacitance which is connected to RES pin (CRES). Where tPWON is assumed to be the time required to reach 90 % of the full level of the power supply, the power supply circuit should be designed to satisfy the following formula. tPWON (ms) 90 x CRES (F) + 162/fOSC (MHz) (tPWON 3000 ms, CRES 0.22 F, and fOSC = 10 in 2-MHz to 10-MHz operation) Note that the power supply voltage (Vcc) must fall below Vpor = 100 mV to remove charge on the RES pin. After that, it can be risen. To remove charge on the RES pin, it is recommended that the diode should be placed to Vcc. If the power supply voltage (Vcc) rises from the point above Vpor, a power-on reset may not occur. tPWON Vcc Vpor Vss Vss PSS-reset signal OVF Internal reset signal 131,072 cycles PSS counter starts Reset released Figure 17.3 Operational Timing of Power-On Reset Circuit Rev. 1.00, 11/03, page 272 of 376 17.3.2 Low-Voltage Detection Circuit LVDR (Reset by Low Voltage Detection) Circuit: Figure 17.4 shows the timing of the operation of the LVDR circuit. The LVDR circuit is enabled after a power-on reset is released. To cancel the LVDR circuit, first the LVDRE bit in LVDCR should be cleared to 0 and then the LVDE bit in LVDCR and, if necessary, the BGRE bit should be cleared to 0. The LVDE and the BGRE bits must not be cleared to 0 simultaneously with the LVDRE bit because incorrect operation may occur. To restart the LVDR circuit, set the LVDE bit and the BGRE bit to 1, wait for 50 s (tLVDON) given by a software timer until the reference voltage and the low-voltage-detection power supply have settled, then set the LVDRE bit to 1. After that, the output settings of ports must be made. When the power-supply voltage falls below the Vreset voltage (2.3 V or 3.6 V (Typ.)), the LVDR circuit clears the LVDRES signal to 0, and resets prescaler S. The low-voltage detection reset state remains in place until a power-on reset is generated. When the power-supply voltage rises above the Vreset voltage again, prescaler S starts counting. It counts 131,072 clock () cycles, and then releases the internal reset signal. In this case, the LVDE, BGRE, VDDII, LVDSEL, and LVDRE bits in LVDCR are not initialized. Note that if the power supply voltage (Vcc) falls below VLVDRmin = 1.0 V and then rises from that point, the low-voltage detection reset may not occur. If the power supply voltage (Vcc) falls below Vpor = 100 mV, a power-on reset occurs. VCC Vreset VLVDRmin VSS PSS-reset signal OVF Internal reset signal 131,072 cycles PSS counter starts Reset released Figure 17.4 Operating Timing of LVDR Circuit Rev. 1.00, 11/03, page 273 of 376 Low Voltage Detection Interrupt (LVDI) Circuit (When Internally Generated Voltage is used for Detection): Figure 17.5 shows the timing of the operation of the LVDI circuit. The LVDI circuit is enabled after a power-on reset, however, the interrupt request is disabled. To enable the LVDI, the LVDDF bit and LVDUF bit in LVDSR must be cleared to 0 and then the LVDDE bit or LVDUE bit in LVDCR must be set to 1. After that, the output settings of ports must be made. To cancel the LVDI, follow the procedures written in section 17.3.2 (4), Operating Procedures for Enabling/Disabling LVDR and LVDI Circuits. To restart the LVDI circuit after standby mode, set the LVDE bit to 1, write 1 to VDDII (if necessary), and wait for 50 s (tLVDON) given by a software timer until the reference voltage and the low-voltage detection power supply have settled. Then, clear the LVDDF and LVDUF bits to 0 and set the LVDDE or the LVDUE bit to 1. After that, the output settings of ports must be made. When the power-supply voltage falls below Vint (D) (Typ. = 3.7 V) voltage, the LVDI circuit clears the LVDINT signal to 0 and sets the LVDDF bit to 1. If the LVDDE bit is 1 at this time, an IRQ0 interrupt request is generated. In this case, the necessary data must be saved in the external EEPROM and a transition to standby mode or subsleep mode must be made. Until this processing is completed, the power supply voltage must be higher than the lower limit of the guaranteed operating voltage. When the power-supply voltage does not fall below the Vreset1 (Typ. = 2.3 V) voltage and rises above the Vint (U) (Typ. = 4.0 V) voltage, the LVDI circuit sets the LVDINT signal to 1. If the LVDUE bit is 1 at this time, the LVDUF bit in LVDSR is set to 1 and an IRQ0 interrupt request is simultaneously generated. If the power supply voltage (Vcc) falls below the Vreset1 (Typ. = 2.3 V) voltage, this LSI enters low voltage detection reset operation (when LVDRE = 1). Rev. 1.00, 11/03, page 274 of 376 Vcc Vint (U) Vint (D) Vreset1 VSS LVDDE LVDDF LVDUE LVDUF IRQ0 interrupt generated IRQ0 interrupt generated Figure 17.5 Operational Timing of LVDI Circuit Low Voltage Detection Interrupt (LVDI) Circuit (When Voltages Input via ExtU and ExtD Pins are used for Detection): Figure 17.6 shows the timing of the LVDI circuit. The LVDI circuit is enabled after a power-on reset, however, the interrupt request is disabled. To enable the LVDI, the LVDDF and LVDUF bits in LVDSR must be cleared to 0 and the LVDDE or LVDUE bit in LVDCR must be set to 1. When using external compared voltage, write 0 to the VDDII bit in LVDCR, and wait for 50 s (tLVDON) given by a software timer until the detection circuit has settled. Then clear the LVDDF and LVDUF bits to 0 and set the LVDDE or LVDUE bit to 1. After that, the output settings of ports must be made. The initial value of the external compared voltages input on the ExtU and ExtD pins must be higher than the Vexd voltage. To cancel the LVDI, follow the procedures written in section 17.3.2 (4), Operating Procedures for Enabling/Disabling LVDR and LVDI Circuits. When the external comparison voltage of ExtD pin falls below the Vexd (D) (Typ. = 1.15 V) voltage, the LVDI clears the LVDINT signal to 0 and sets the LVDDF bit in LVDSR to 1. If the LVDDE bit is 1 at this time, an IRQ0 interrupt request is generated. In this case, the necessary data must be saved in the external EEPROM, and a transition to standby mode or subsleep mode must be made. Until this processing is completed, the power supply voltage must be higher than the lower limit of the guaranteed operating voltage. When the power-supply voltage does not fall below the Vreset1 (Typ. = 2.3 V) voltage and the input voltage of the ExtU pin rises above Vexd (Typ. = 1.15 V) voltage, the LVDI circuit sets the LVDINT signal to 1. If the LVDUE bit is 1 at this time, the LVDUF bit in LVDSR is set to 1 and an IRQ0 interrupt request is generated. Rev. 1.00, 11/03, page 275 of 376 If the power supply voltage falls below the Vreset1 (Typ. = 2.3 V) voltage, this LSI enters lowvoltage detection reset operation. When the voltages input on the ExtU and ExtD pins are used as the compared voltage, ensure to use the LVDR (reset detection voltage: Typ. = 2.3 V) circuit. External power supply voltage ExtD input voltage ExtU input voltage (1) (2) (3) (4) Vreset1 VSS Vexd LVDDE LVDDF LVDUE LVDUF IRQ0 interrupt generated IRQ0 interrupt generated Figure 17.6 Operational Timing of LVDI Circuit (When Compared Voltage is Input through ExtU and ExtD Pins)) Rev. 1.00, 11/03, page 276 of 376 Operating Procedures for Enabling/Disabling LVDR and LVDI Circuits: The low-voltage detection circuit is enabled after reset. To enable or disable the low-voltage detection circuit correctly, follow the procedure described below. Figure 17.7 shows the timing for the operation and release of the low-voltage detection circuit. 1. To disable the low-voltage detection circuit, clear all of the LVDRE, LVDDE, and LVDUE bits to 0. Then, clear the LVDE and BGRE bits to 0. Set the VDDII bit in LVDCR if necessary. The LVDE and BGRE bits must not be cleared to 0 at the same timing as the LVDRE, LVDDE, and LVDUE bits because incorrect operation may occur. To enable the low-voltage detection circuit, set the LVDE and BGRE bits in LVDCR to 1. When the voltages input on the ExtU and ExtD pins are used as the compared voltage, clear the LVDDII bit to 0. Wait for 50 s (tLVDON) given by a software timer until the reference voltage and the lowvoltage-detection power supply have settled. Then, clear the LVDDF and LVDUF bits in LVDSR to 0 and set the LVDRE, LVDDE, and LVDUE bits in LVDCR to 1, if necessary. LVDE 2. 3. BGRE VDDII LVDRE LVDDE LVDUE Longer than one instruction operation time tLVDON Figure 17.7 Timing for Enabling/Disabling of Low-Voltage Detection Circuit Rev. 1.00, 11/03, page 277 of 376 Rev. 1.00, 11/03, page 278 of 376 Section 18 Power Supply Circuit This LSI incorporates an internal power supply step-down circuit. Use of this circuit enables the internal power supply to be fixed at a constant level of approximately 3.0 V, independently of the voltage of the power supply connected to the external VCC pin. As a result, the current consumed when an external power supply is used at 3.0 V or above can be held down to virtually the same low level as when used at approximately 3.0 V. If the external power supply is 3.0 V or below, the internal voltage will be practically the same as the external voltage. It is, of course, also possible to use the same level of external power supply voltage and internal power supply voltage without using the internal power supply step-down circuit. 18.1 When Using Internal Power Supply Step-Down Circuit Connect the external power supply to the VCC pin, and connect a capacitance of approximately 0.1 F between VCL and VSS, as shown in figure 18.1. The internal step-down circuit is made effective simply by adding this external circuit. In the external circuit interface, the external power supply voltage connected to VCC and the GND potential connected to VSS are the reference levels. For example, for port input/output levels, the VCC level is the reference for the high level, and the VSS level is that for the low level. The A/D converter analog power supply is not affected by the internal step-down circuit. VCC VCC = 3.0 to 5.5 V Step-down circuit VCL Internal logic Internal power supply VSS Stabilization capacitance (approx. 0.1 F) Figure 18.1 Power Supply Connection when Internal Step-Down Circuit is Used PSCKT00A_000020020200 Rev. 1.00, 11/03, page 279 of 376 18.2 When Not Using Internal Power Supply Step-Down Circuit When the internal power supply step-down circuit is not used, connect the external power supply to the VCL pin and VCC pin, as shown in figure 18.2. The external power supply is then input directly to the internal power supply. The permissible range for the power supply voltage is 3.0 V to 3.6 V. Operation cannot be guaranteed if a voltage outside this range (less than 3.0 V or more than 3.6 V) is input. VCC VCC = 3.0 to 3.6 V Step-down circuit VCL Internal logic Internal power supply VSS Figure 18.2 Power Supply Connection when Internal Step-Down Circuit is Not Used Rev. 1.00, 11/03, page 280 of 376 Section 19 List of Registers The register list gives information on the on-chip I/O register addresses, how the register bits are configured, and the register states in each operating mode. The information is given as shown below. 1. Register addresses (address order) * Registers are listed from the lower allocation addresses. * Registers are classified by functional modules. * The data bus width is indicated. * The number of access states is indicated. 2. Register bits * Bit configurations of the registers are described in the same order as the register addresses. * Reserved bits are indicated by in the bit name column. * When registers consist of 16 bits, bits are described from the MSB side. 3. Register states in each operating mode * Register states are described in the same order as the register addresses. * The register states described here are for the basic operating modes. If there is a specific reset for an on-chip peripheral module, refer to the section on that on-chip peripheral module. Rev. 1.00, 11/03, page 281 of 376 19.1 Register Addresses (Address Order) The data bus width indicates the numbers of bits by which the register is accessed. The number of access states indicates the number of states based on the specified reference clock. Register Name Low-voltage-detection control register Low-voltage-detection status register Clock control status register RC control register Abbreviation LVDCR Bit No 8 Module Address Name H'F730 Data Bus Access Width State 2 Low-voltage 8 detection circuit Low-voltage 8 detection circuit Clock oscillator 8 LVDSR 8 H'F731 2 CKCSR RCCR 8 8 H'F734 H'F735 H'F736 H'F737 H'F748 H'F749 H'F74A H'F74B H'F74C H'F74D H'F74E H'F74F H'F760 H'F761 H'FF80 H'FF81 H'FF82 H'FF83 H'FF84 H'FF85 H'FF86 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 1 Internal RC 8 oscillator Internal RC 8 oscillator Internal RC 8 oscillator IIC2 IIC2 IIC2 IIC2 IIC2 IIC2 IIC2 IIC2 Timer B1 Timer B1 Timer W Timer W Timer W Timer W Timer W Timer W Timer W 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 16* RC trimming data protect register RCTRMDPR 8 RC trimming data register I C bus control register 1 I C bus control register 2 I C bus mode register I C bus interrupt enable register I C bus status register Slave address register I C bus transmit data register I C bus receive data register Timer mode register B1 Timer counter B1 Timer mode register W Timer control register W Timer status register W Timer I/O control register 0 Timer I/O control register 1 Timer counter Rev. 1.00, 11/03, page 282 of 376 2 2 2 2 2 2 2 RCTRMDR ICCR1 ICCR2 ICMR ICIER ICSR SAR ICDRT ICDRR TMB1 TCB1 TMRW TCRW TSRW TIOR0 TIOR1 TCNT 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 16 Timer interrupt enable register W TIERW 2 Register Name General register A General register B General register C General register D Flash memory control register 1 Flash memory control register 2 Erase block register 1 Flash memory enable register Timer control register V0 Timer control/status register V Timer constant register A Timer constant register B Timer counter V Timer control register V1 Serial mode register Bit rate register Serial control register 3 Transmit data register Serial status register Receive data register Sampling mode register A/D data register A A/D data register B A/D data register C A/D data register D A/D control/status register A/D control register Timer counter WD Timer mode register WD Address break control register Address break status register Break address register H Abbreviation GRA GRB GRC GRD Bit No 16 16 16 16 Module Address Name H'FF88 H'FF8A H'FF8C H'FF8E H'FF90 H'FF91 H'FF93 H'FF9B H'FFA0 H'FFA1 H'FFA2 H'FFA3 H'FFA4 H'FFA5 H'FFA8 H'FFA9 Timer W Timer W Timer W Timer W ROM ROM ROM ROM Timer V Timer V Timer V Timer V Timer V Timer V SCI3 SCI3 Data Bus Access Width State 16* 16* 16* 16* 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 1 1 1 1 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 2 2 2 2 2 2 FLMCR1 8 FLMCR2 8 EBR1 FENR TCRV0 TCSRV TCORA TCORB TCNTV TCRV1 SMR BRR SCR3 TDR SSR RDR SPMR ADDRA ADDRB ADDRC ADDRD ADCSR ADCR TCWD TMWD 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 16 16 16 16 8 8 8 8 H'FFAA SCI3 H'FFAB SCI3 H'FFAC SCI3 H'FFAD SCI3 H'FFAE SCI3 H'FFB0 H'FFB2 H'FFB4 H'FFB6 H'FFB8 H'FFB9 H'FFC0 H'FFC1 H'FFC2 H'FFC8 H'FFC9 A/D converter A/D converter A/D converter A/D converter A/D converter A/D converter WDT* WDT* WDT* 2 2 2 Timer control/status register WD TCSRWD 8 ABRKCR 8 ABRKSR 8 BARH 8 Address break 8 Address break 8 H'FFCA Address break 8 Rev. 1.00, 11/03, page 283 of 376 Register Name Break address register L Break data register H Break data register L Port pull-up control register 1 Port pull-up control register 5 Port data register 1 Port data register 2 Port data register 5 Port data register 7 Port data register 8 Port data register B Port data register C Port mode register 1 Port mode register 5 Port control register 1 Port control register 2 Port control register 5 Port control register 7 Port control register 8 Port control register C System control register 1 System control register 2 Interrupt edge select register 1 Interrupt edge select register 2 Interrupt enable register 1 Interrupt enable register 2 Interrupt flag register 1 Interrupt flag register 2 Wake-up interrupt flag register Module standby control register 1 Module standby control register 2 Abbreviation BARL BDRH BDRL PUCR1 PUCR5 PDR1 PDR2 PDR5 PDR7 PDR8 PDRB PDRC PMR1 PMR5 PCR1 PCR2 PCR5 PCR7 PCR8 PCRC Bit No 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 Module Address Name H'FFCB H'FFCC H'FFCD H'FFD0 H'FFD1 H'FFD4 H'FFD5 H'FFD8 H'FFDA H'FFDB H'FFDD H'FFDE H'FFE0 H'FFE1 H'FFE4 H'FFE5 H'FFE8 H'FFEA H'FFEB H'FFEE H'FFF0 H'FFF1 H'FFF2 H'FFF3 H'FFF4 H'FFF5 H'FFF6 H'FFF7 H'FFF8 H'FFF9 H'FFFA Data Bus Access Width State 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 Address break 8 Address break 8 Address break 8 I/O port I/O port I/O port I/O port I/O port I/O port I/O port I/O port I/O port I/O port I/O port I/O port I/O port I/O port I/O port I/O port I/O port Power-down Power-down Interrupts Interrupts Interrupts Interrupts Interrupts Interrupts Interrupts Power-down Power-down 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 SYSCR1 8 SYSCR2 8 IEGR1 IEGR2 IENR1 IENR2 IRR1 IRR2 IWPR 8 8 8 8 8 8 8 MSTCR1 8 MSTCR2 8 Notes: 1. Only word access can be used. 2. WDT: Watchdog timer Rev. 1.00, 11/03, page 284 of 376 19.2 Register Bits Register bit names of the on-chip peripheral modules are described below. Each line covers eight bits, and 16-bit registers are shown as 2 lines. Register Name LVDCR LVDSR CKCSR RCCR Bit 7 LVDE -- Bit 6 BGRE -- Bit 5 VDDII -- Bit 4 -- -- Bit 3 Bit 2 Bit 1 LVDDE LVDDF Bit 0 LVDUE LVDUF Clock oscillator Module Name LVDC LVDSEL LVDRE -- -- PMRC1 PMRC0 OSCBAKE OSCSEL RCSTP FSEL PRWE RCVD SCP WAIT TEIE TEND SVA5 VCLSEL -- CKSWIE CKSWIF OSCHLT CKSTA -- -- CKS3 SCLO BCWP STIE STOP SVA2 -- -- CKS2 -- BC2 ACKE SVA1 RCPSC1 RCPSC0 Internal RC oscillator -- CKS1 IICRST BC1 ACKBR SVA0 -- TRMD0 CKS0 -- BC0 ACKBT ADZ FS ICDRT0 ICDRR0 TMB10 TCB10 PWMB TOA IMIEA IMFA IOA0 IOC0 TCNT8 TCNT0 GRA8 GRA0 GRB8 GRB0 Timer W Timer B1 IIC2 RCTRMDPR WRI RCTRMDR ICCR1 ICCR2 ICMR ICIER ICSR SAR ICDRT ICDRR TMB1 TCB1 TMRW TCRW TIERW TSRW TIOR0 TIOR1 TCNT GRA GRB TRMD7 ICE BBSY MLS TIE TDRE SVA6 LOCKDW TRMDRWE TRMD4 TRS SDAOP -- NAKIE NACKF SVA3 ICDRT4 ICDRR4 -- TCB14 BUFEA CKS0 -- -- IOB0 IOD0 TCNT12 TCNT4 GRA12 GRA4 GRB12 GRB4 MST SDAO -- RIE RDRF SVA4 TRMD6 TRMD5 TRMD3 TRMD2 TRMD1 AL/OVE AAS ICDRT7 ICDRT6 ICDRT5 ICDRR7 ICDRR6 ICDRR5 TMB17 TCB17 CTS CCLR OVIE OVF -- -- TCNT7 GRA15 GRA7 GRB15 GRB7 -- TCB16 -- CKS2 -- -- IOB2 IOD2 TCNT6 GRA6 GRB6 -- TCB15 BUFEB CKS1 -- -- IOB1 IOD1 TCNT5 GRA5 GRB5 ICDRT3 ICDRT2 ICDRT1 ICDRR3 ICDRR2 ICDRR1 -- TCB13 -- TOD IMIED IMFD -- -- TCNT3 GRA11 GRA3 GRB11 GRB3 TMB12 TCB12 PWMD TOC IMIEC IMFC IOA2 IOC2 TCNT2 GRA10 GRA2 GRB10 GRB2 TMB11 TCB11 PWMC TOB IMIEB IMFB IOA1 IOC1 TCNT1 GRA9 GRA1 GRB9 GRB1 TCNT15 TCNT14 TCNT13 GRA14 GRA13 GRB14 GRB13 TCNT11 TCNT10 TCNT9 Rev. 1.00, 11/03, page 285 of 376 Register Name GRC GRD FLMCR1 FLMCR2 EBR1 FENR TCRV0 TCSRV TCORA TCORB TCNTV TCRV1 SMR BRR SCR3 TDR SSR RDR SPMR ADDRA ADDRB ADDRC ADDRD ADCSR ADCR TCWD TMWD Bit 7 GRC15 GRC7 GRD15 GRD7 -- FLER -- FLSHE CMIEB CMFB Bit 6 GRC14 GRC6 GRD14 GRD6 SWE -- -- -- CMIEA CMFA Bit 5 GRC13 GRC5 GRD13 GRD5 ESU -- EB5 -- OVIE OVF Bit 4 GRC12 GRC4 GRD12 GRD4 PSU -- EB4 -- CCLR1 -- Bit 3 GRC11 GRC3 GRD11 GRD3 EV -- EB3 -- CCLR0 OS3 Bit 2 GRC10 GRC2 GRD10 GRD2 PV -- EB2 -- CKS2 OS2 Bit 1 GRC9 GRC1 GRD9 GRD1 E -- EB1 -- CKS1 OS1 Bit 0 GRC8 GRC0 GRD8 GRD0 P -- EB0 -- CKS0 OS0 Module Name Timer W ROM Timer V TCORA7 TCORA6 TCORA5 TCORA4 TCORA3 TCORA2 TCORA1 TCORA0 TCORB7 TCORB6 TCORB5 TCORB4 TCORB3 TCORB2 TCORB1 TCORB0 TCNTV7 TCNTV6 TCNTV5 TCNTV4 TCNTV3 TCNTV2 TCNTV1 TCNTV0 -- COM BRR7 TIE TDR7 TDRE RDR7 -- AD9 AD1 AD9 AD1 AD9 AD1 AD9 AD1 ADF TRGE TCWD7 -- -- CHR BRR6 RIE TDR6 RDRF RDR6 -- AD8 AD0 AD8 AD0 AD8 AD0 AD8 AD0 ADIE -- TCWE TCWD6 -- -- PE BRR5 TE TDR5 OER RDR5 -- AD7 -- AD7 -- AD7 -- AD7 -- ADST -- B4WI TCWD5 -- TVEG1 PM BRR4 RE TDR4 FER RDR4 -- AD6 -- AD6 -- AD6 -- AD6 -- SCAN -- TCWD4 -- TVEG0 STOP BRR3 MPIE TDR3 PER RDR3 -- AD5 -- AD5 -- AD5 -- AD5 -- CKS -- TCWD3 CKS3 TRGE MP BRR2 TEIE TDR2 TEND RDR2 AD4 -- AD4 -- AD4 -- AD4 -- CH2 -- WDON TCWD2 CKS2 -- CKS1 BRR1 CKE1 TDR1 MPBR RDR1 AD3 -- AD3 -- AD3 -- AD3 -- CH1 -- B0WI TCWD1 CKS1 ICKS0 CKS0 BRR0 CKE0 TDR0 MPBT RDR0 -- AD2 -- AD2 -- AD2 -- AD2 -- CH0 -- WRST TCWD0 CKS0 WDT* A/D converter SCI3 STDSPM -- TCSRWD B6WI TCSRWE B2WI Rev. 1.00, 11/03, page 286 of 376 Register Name Bit 7 Bit 6 CSEL1 ABIE BARH6 BARL6 BDRH6 BDRL6 -- -- -- P56 P76 -- -- -- -- -- -- -- PCR56 PCR76 -- -- STS2 -- -- -- -- -- -- -- -- MSTIIC -- Bit 5 CSEL0 -- BARH5 BARL5 BDRH5 BDRL5 -- -- -- P55 P75 -- -- -- -- WKP5 -- -- PCR55 PCR75 -- -- STS1 DTON -- WPEG5 IENWP IENTB1 -- IRRTB1 IWPF5 MSTS3 -- Bit 4 ACMP2 -- BARH4 BARL4 BDRH4 BDRL4 Bit 3 ACMP1 -- BARH3 BARL3 BDRH3 BDRL3 -- -- -- -- -- P83 PB3 -- -- -- -- -- -- -- PCR83 -- -- MA1 IEG3 -- IEN3 -- IRRI3 -- -- Bit 2 ACMP0 -- BARH2 BARL2 BDRH2 BDRL2 -- -- -- P22 -- -- P82 PB2 -- -- -- -- PCR22 -- -- PCR82 -- -- MA0 -- -- -- -- -- -- -- -- Bit 1 DCMP1 -- BARH1 BARL1 BDRH1 BDRL1 -- -- -- P21 -- -- P81 PB1 PC1 TXD -- -- PCR21 -- -- PCR81 PCRC1 -- -- -- -- -- -- -- -- -- MSTTV -- Bit 0 DCMP0 -- BARH0 BARL0 BDRH0 BDRL0 -- -- -- P20 -- -- P80 PB0 PC0 -- -- -- PCR20 -- -- PCR80 PCRC0 -- -- IEG0 -- IEN0 -- IRRI0 -- -- -- -- Module Name Address break ABRKCR RTINTE ABRKSR ABIF BARH BARL BDRH BDRL PUCR1 PUCR5 PDR1 PDR2 PDR5 PDR7 PDR8 PDRB PDRC PMR1 PMR5 PCR1 PCR2 PCR5 PCR7 PCR8 PCRC SYSCR1 SYSCR2 IEGR1 IEGR2 IENR1 IENR2 IRR1 IRR2 IWPR BARH7 BARL7 BDRH7 BDRL7 -- P17 -- P57 -- -- -- -- IRQ3 -- PCR17 -- PCR57 -- -- -- SSBY SMSEL -- -- IENDT -- IRRDT -- -- PUCR17 -- PUCR14 -- P14 -- -- P74 P84 -- -- IRQ0 -- PCR14 -- -- PCR74 PCR84 -- STS0 MA2 -- -- -- -- -- -- -- MSTAD I/O port PUCR55 -- Power-down Interrupts MSTCR1 -- MSTCR2 -- MSTWD MSTTW Power-down MSTTB1 -- Note: WDT:Watchdog timer Rev. 1.00, 11/03, page 287 of 376 19.3 Register Name LVDCR LVDSR CKCSR RCCR Register States in Each Operating Mode Reset Active Sleep -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Subsleep -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Initialized Initialized Initialized Initialized Standby -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Initialized Initialized Initialized Initialized ROM Timer W Timer B1 IIC2 Clock oscillator RC oscillation Module LVDC Initialized -- Initialized -- Initialized -- Initialized -- Initialized -- Initialized -- Initialized -- Initialized -- Initialized -- Initialized -- Initialized -- Initialized -- Initialized -- Initialized -- Initialized -- Initialized -- Initialized -- Initialized -- Initialized -- Initialized -- Initialized -- Initialized -- Initialized -- Initialized -- Initialized -- Initialized -- Initialized -- Initialized -- Initialized -- Initialized -- RCTRMDPR Initialized -- RCTRMDR ICCR1 ICCR2 ICMR ICIER ICSR SAR ICDRT ICDRR TMB1 TCB1 TMRW TCRW TIERW TSRW TIOR0 TIOR1 TCNT GRA GRB GRC GRD FLMCR1 FLMCR2 EBR1 FENR Rev. 1.00, 11/03, page 288 of 376 Register Name TCRV0 TCSRV TCORA TCORB TCNTV TCRV1 SMR BRR SCR3 TDR SSR RDR SPMR ADDRA ADDRB ADDRC ADDRD ADCSR ADCR TCWD TMWD Reset Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Active -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Sleep -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Subsleep Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Standby Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Module Timer V SCI3 A/D converter TCSRWD Initialized WDT* ABRKCR Initialized ABRKSR Initialized BARH BARL BDRH BDRL PUCR1 PUCR5 PDR1 PDR2 PDR5 PDR7 PDR8 PDRB Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Address Break I/O port Rev. 1.00, 11/03, page 289 of 376 Register Name PDRC PMR1 PMR5 PCR1 PCR2 PCR5 PCR7 PCR8 PCRC SYSCR1 SYSCR2 IEGR1 IEGR2 IENR1 IENR2 IRR1 IRR2 IWPR Reset Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Initialized Active -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Sleep -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Subsleep -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Standby -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Module I/O port Power-down Interrupts MSTCR1 Initialized MSTCR2 Initialized Power-down Note: is not initialized * WDT: Watchdog timer Rev. 1.00, 11/03, page 290 of 376 Section 20 Electrical Characteristics 20.1 Absolute Maximum Ratings Table 20.1 Absolute Maximum Ratings Item Power supply voltage Analog power supply voltage Input voltage Ports other than port B Port B Operating temperature Storage temperature Note: * Topr Tstg Symbol VCC AVCC VIN Value -0.3 to +7.0 -0.3 to +7.0 -0.3 to VCC +0.3 -20 to +75 -55 to +125 Unit V V V C C Note * -0.3 to AVCC +0.3 V Permanent damage may result if maximum ratings are exceeded. Normal operation should be under the conditions specified in Electrical Characteristics. Exceeding these values can result in incorrect operation and reduced reliability. Rev. 1.00, 11/03, page 291 of 376 20.2 20.2.1 Electrical Characteristics (F-ZTATTM Version) Power Supply Voltage and Operating Ranges 1. Supply voltage and oscillation frequency range osc(MHz) 10.0 2.0 3.0 5.5 AVcc = 3.0 to 5.5 V Active mode Sleep mode Vcc(V) 2. Power supply voltage and operating frequency range (MHz) 10.0 (kHz) 1250 2.0 31.25 3.0 5.5 Vcc(V) 3.0 5.5 Vcc(V) AVcc = 3.0 to 5.5 V Active mode Sleep mode (When MA2 = 0 in SYSCR2) AVcc = 3.0 to 5.5 V Active mode Sleep mode (When MA2 = 1 in SYSCR2) Rev. 1.00, 11/03, page 292 of 376 3. Analog power supply voltage and A/D converter accuracy guarantee range (MHz) 10.0 2.0 3.0 5.5 Vcc = 3.0 to 5.5 V Active mode Sleep mode AVcc(V) Rev. 1.00, 11/03, page 293 of 376 20.2.2 DC Characteristics Table 20.2 DC Characteristics (1) VCC = 3.0 V to 5.5 V, VSS = 0.0 V, Ta = -20C to +75C unless otherwise indicated. Applicable Pins Test Condition Values Min. VCC x 0.8 VCC x 0.9 Typ. Max. -- -- VCC + 0.3 VCC + 0.3 Unit V V Notes Item Symbol Input high VIH voltage RES, NMI, WKP5, VCC = 4.0 V to 5.5 V IRQ0, IRQ3, ADTRG, TMRIV, TMCIV, FTCI, FTIOA to FTIOD, SCK3, TRGV RXD, SCL, SDA, VCC = 4.0 V to 5.5 V P17, P14, P22 to P20, P57 to P55, P76 to P74, P84 to P80, PC1, PC0 PB3 to PB0 AVCC = 4.0 V to 5.5 V AVCC = 3.0 V to 5.5 V OSC1 VCC = 4.0 V to 5.5 V VCC x 0.7 VCC x 0.8 -- -- VCC + 0.3 VCC + 0.3 V V AVCC x 0.7 -- AVCC x 0.8 -- VCC - 0.5 VCC - 0.3 -0.3 -- -- AVCC + 0.3 AVCC + 0.3 VCC + 0.3 VCC + 0.3 VCC x 0.2 V V V V V Input low voltage VIL RES, NMI, WKP5, VCC = 4.0 V to 5.5 V IRQ0, IRQ3, ADTRG, TMRIV, TMCIV, FTCI, FTIOA to FTIOD, SCK3, TRGV RXD, SCL, SDA, P17, P14, P22 to P20, P57 to P55, P76 to P74, P84 to P80, PC1, PC0 PB3 to PB0 OSC1 VCC = 4.0 V to 5.5 V -0.3 -- VCC x 0.1 V -0.3 -- VCC x 0.3 V -0.3 -- VCC x 0.2 V AVCC = 4.0 V to 5.5 V AVCC = 3.0 V to 5.5 V VCC = 4.0 V to 5.5 V -0.3 -0.3 -0.3 -0.3 -- -- -- -- AVCC x 0.3 V AVCC x 0.2 0.5 0.3 V V Rev. 1.00, 11/03, page 294 of 376 Item Output high voltage Symbol VOH Applicable Pins P17, P14, P22 to P20, P55, P76 to P74, P84 to P80, PC1, PC0 P56, P57 Test Condition -IOH = 5 mA Values Min. Typ. -- -- Max. -- -- Unit V V Notes VCC = 4.0 V to 5.5 V VCC - 1.0 -IOH = 0.1 mA VCC - 0.5 VCC = 4.0 V to 5.5 V VCC - 2.5 -I = 0.1 mA OH -- -- -- -- -- -- -- -- -- -- -- -- -- 0.6 0.4 1.5 1.0 0.4 0.4 0.6 0.4 1.0 V V V V V V V V V V A VCC = 3.0 V to 4.0 V VCC - 2.0 -I = 0.1 mA OH Output low VOL voltage P17, P14, P22 to P20, P57 to P55, P76 to P74, PC1, PC0 P84 to P80 VCC = 4.0 V to 5.5 V -- IOL = 1.6 mA IOL = 0.4 mA -- VCC = 4.0 V to 5.5 V -- IOL = 20.0 mA VCC = 4.0 V to 5.5 V -- IOL = 10.0 mA VCC = 4.0 V to 5.5 V -- IOL = 1.6 mA IOL = 0.4 mA -- SCL, SDA VCC = 4.0 V to 5.5 V -- IOL = 6.0 mA IOL = 3.0 mA -- -- Input/ output leakage current | IIL | OSC1, RES, NMI, VIN = 0.5 V to WKP5, (VCC - 0.5 V) IRQ0, IRQ3, ADTRG, TRGV, TMRIV, TMCIV, FTCI, FTIOA to FTIOD, RXD, SCK3, SCL, SDA P17, P14, P22 to P20, P57 to P55, P76 to P74, P84 to P80, PC1, PC0 PB3 to PB0 VIN = 0.5 V to (VCC - 0.5 V) -- -- 1.0 A VIN = 0.5 V to (AVCC - 0.5 V) -- -- 1.0 A Rev. 1.00, 11/03, page 295 of 376 Item Pull-up MOS current Input capacitance Symbol -Ip Applicable Pins P17, P14, P55 Test Condition VCC = 5.0 V, VIN = 0.0 V VCC = 3.0 V, VIN = 0.0 V Values Min. 50.0 -- -- Typ. -- 60.0 -- Max. 300.0 -- 15.0 Unit A A pF Reference value Notes Cin All input pins except power supply pins VCC f = 1 MHz, VIN = 0.0 V, Ta = 25C Active mode 1 VCC = 5.0 V, fOSC = 10 MHz Active mode 1 VCC = 3.0 V, fOSC = 10 MHz Active IOPE1 mode current consumption IOPE2 -- TBD TBD mA * -- TBD -- mA Reference value* * VCC Active mode 2 VCC = 5.0 V, fOSC = 10 MHz Active mode 2 VCC = 3.0 V, fOSC = 10 MHz -- TBD TBD mA -- TBD -- mA Reference value* * Sleep ISLEEP1 mode current consumption ISLEEP2 VCC Sleep mode 1 VCC = 5.0 V, fOSC = 10 MHz Sleep mode 1 VCC = 3.0 V, fOSC = 10 MHz -- TBD TBD mA -- TBD -- mA Reference value* * VCC Sleep mode 2 VCC = 5.0 V, fOSC = 10 MHz Sleep mode 2 VCC = 3.0 V, fOSC = 10 MHz -- TBD TBD mA -- TBD -- mA Reference value* Subsleep ISUBSP mode current consumption ISTBY Standby mode current consumption RAM data VRAM retaining voltage VCC VCC = 3.0 V -- -- TBD A VCC -- -- TBD A * VCC 2.0 -- -- V Rev. 1.00, 11/03, page 296 of 376 Note: * Pin states during current consumption measurement are given below (excluding current in the pull-up MOS transistors and output buffers). RES Pin VCC VCC VCC Internal State Operates Operates (/64) Only timers operate Only timers operate (/64) CPU and timers both stop VCC System clock: Internal RC oscillator VCC Other Pins VCC Oscillator Pins System clock: Internal RC oscillator Mode Active mode 1 Active mode 2 Sleep mode 1 Sleep mode 2 Standby mode Rev. 1.00, 11/03, page 297 of 376 Table 20.2 DC Characteristics (2) VCC = 3.0 V to 5.5 V, VSS = 0.0 V, Ta = -20C to +75C, unless otherwise indicated. Application Symbol Pins Test Condition Values Min. Typ. -- Max. 2.0 Unit mA Item Allowable output low IOL current (per pin) Output pins except VCC = 4.0 V to 5.5 V -- P84 to P80, SCL, and SDA P84 to P80 Output pins except P84 to P80, SCL, and SDA P84 to P80 SCL, SDA -- -- -- -- 20.0 0.5 mA mA -- -- -- -- -- 10.0 6.0 40.0 mA mA mA Allowable output low IOL current (total) Output pins except VCC = 4.0 V to 5.5 V -- P84 to P80, SCL, and SDA P84 to P80, SCL, and SDA Output pins except P84 to P80, SCL, and SDA P84 to P80, SCL, and SDA -- -- -- -- 80.0 20.0 mA mA -- VCC = 4.0 V to 5.5 V -- -- VCC = 4.0 V to 5.5 V -- -- VCC = 4.0 V to 5.5 V -- -- -- -- -- -- -- -- -- 40.0 5.0 0.2 2.0 0.2 T.B.D 8.0 mA mA mA mA mA mA mA Allowable output high I -IOH I current (per pin) Output pins except P56, P57 P56, P57 Allowable output high I -IOH All output pins current (total) I Rev. 1.00, 11/03, page 298 of 376 20.2.3 AC Characteristics Table 20.3 AC Characteristics VCC = 3.0 V to 5.5 V, VSS = 0.0 V, Ta = -20C to +75C, unless otherwise specified. Applicable Symbol Pins OSC1, OSC2 Test Condition Values Min. Typ. 2.0 1 -- 2 OSC1, OSC2 OSC1, OSC2 -- -- -- -- -- -- -- -- Max. 10.0 64 32.0 -- 10.0 5.0 Unit MHz tOSC s tcyc ms ms Reference Figure *1 *2 Item System clock fOSC oscillation frequency System clock () cycle tcyc time Instruction cycle time Oscillation stabilization trc time (crystal resonator) Oscillation stabilization trc time (ceramic resonator) External clock high width External clock low width tCPH tCPL OSC1 OSC1 OSC1 OSC1 RES 40.0 -- 40.0 -- -- -- -- -- -- -- 15.0 15.0 -- ns ns ns ns ns Figure 20.1 External clock rise time tCPr External clock fall time tCPf RES pin low width tREL At power-on and TBD -- in modes other than those below In active mode TBD -- and sleep mode operation Figure 20.2 -- ns Input pin high width tIH IRQ0 , IRQ3, WKP5, NMI, TMCIV, TMRIV, TRGV, ADTRG, FTCI, FTIOA to FTIOD IRQ0, IRQ3, WKP5, NMI, TMCIV, TMRIV, TRGV, ADTRG, FTCI, FTIOA to FTIOD 2 -- -- tcyc Figure 20.3 Input pin low width tIL 2 -- -- tcyc Notes: 1. When an external clock is input, the minimum system clock oscillator frequency is 2.0 MHz. 2. Determined by MA2 to MA0 in system control register 2 (SYSCR2). Rev. 1.00, 11/03, page 299 of 376 Table 20.4 I2C Bus Interface Timing VCC = 3.0 to 5.5 V, VSS = 0.0 V, Ta = -20 to +75C, unless otherwise indicated. Applicable Test Symbol Pins Condition Min. Values Typ. Reference Max. Unit Figure Item SCL input cycle time SCL input high pulse width SCL input low pulse width tSCL tSCLH tSCLL 12tcyc + 600 300 1tcyc ns ns ns ns ns Figure 20.4 3tcyc + 300 5tcyc + 300 SCL and SDA input fall tSf time SCL and SDA input spike pulse removal time SDA input bus-free time Start condition input hold time Retransmission start condition input setup time Setup time for stop condition input Data input setup time Data input hold time Capacitive load of SCL and SDA SCL and SDA output fall time tSP tBUF tSTAH tSTAS 5tcyc 3tcyc 3tcyc ns ns ns tSTOS tSDAS tSDAH cb tSf VCC = 4.0 to 5.5 V 3tcyc 1tcyc+ 20 0 0 400 250 300 ns ns ns pF ns ns Rev. 1.00, 11/03, page 300 of 376 Table 20.5 Serial Interface (SCI3) Timing VCC = 3.0 V to 5.5 V, VSS = 0.0 V, Ta = -20C to +75C, unless otherwise specified. Applicable Pins Test Condition Values Min. Typ. Max. Reference Unit Figure Item Symbol Input clock cycle Asynchronous Clocked synchronous Tscyc SCK3 4 6 -- -- -- -- -- -- 0.6 1 tcyc tcyc Tscyc tcyc Figure 20.5 Input clock pulse width tSCKW Transmit data delay time (clocked synchronous) Receive data setup time (clocked synchronous) Receive data hold time (clocked synchronous) tTXD SCK3 TXD 0.4 -- Figure 20.6 tRXS RXD 100.0 -- -- ns tRXH RXD 100.0 -- -- ns Rev. 1.00, 11/03, page 301 of 376 20.2.4 A/D Converter Characteristics Table 20.6 A/D Converter Characteristics VCC = 3.0 V to 5.5 V, VSS = 0.0 V, Ta = -20C to +75C, unless otherwise specified. Applicable Test Pins Condition AVCC AN3 to AN0 AVCC Values Min. 3.0 VSS - 0.3 AVCC = 5.0 V -- fOSC = 10 MHz AISTOP1 AVCC -- 50 -- A *2 Reference value *3 Typ. VCC -- -- Max. 5.5 Unit V Notes *1 Item Analog power supply voltage Analog input voltage Analog power supply current Symbol AVCC AVIN AIOPE AVCC + V 0.3 2.0 mA AISTOP2 Analog input capacitance CAIN Allowable signal source impedance Resolution (data length) Conversion time (single mode) Nonlinearity error Offset error Full-scale error Quantization error Absolute accuracy Conversion time (single mode) Nonlinearity error Offset error Full-scale error Quantization error Absolute accuracy RAIN AVCC AN3 to AN0 AN3 to AN0 -- -- -- 10 AVCC = 3.0 V 134 to 5.5 V -- -- -- -- -- AVCC = 4.0 V 70 to 5.5 V -- -- -- -- -- -- -- -- 10 -- -- -- -- -- -- -- -- -- -- -- -- 5.0 30.0 5.0 10 -- 7.5 7.5 7.5 0.5 8.0 -- 7.5 7.5 7.5 0.5 8.0 A pF k bit tcyc LSB LSB LSB LSB LSB tcyc LSB LSB LSB LSB LSB Rev. 1.00, 11/03, page 302 of 376 Item Conversion time (single mode) Nonlinearity error Offset error Full-scale error Quantization error Absolute accuracy Symbol Applicable Pins Test Condition Values Min. Typ. -- -- -- -- -- -- Max. -- 3.5 3.5 3.5 0.5 4.0 Unit tcyc LSB LSB LSB LSB LSB Notes AVCC = 4.0 V 134 to 5.5 V -- -- -- -- -- Notes: 1. Set AVCC = VCC when the A/D converter is not used. 2. AISTOP1 is the current in active and sleep modes while the A/D converter is idle. 3. AISTOP2 is the current at reset and in standby and subsleep modes while the A/D converter is idle. 20.2.5 Watchdog Timer Characteristics Table 20.7 Watchdog Timer Characteristics VCC = 3.0 V to 5.5 V, VSS = 0.0 V, Ta = -20C to +75C, unless otherwise specified. Applicable Pins Test Condition Values Min. 0.2 Typ. 0.4 Max. -- Unit s Notes * Item Internal oscillator overflow time Note: * Symbol tOVF Shows the time to count from 0 to 255, at which point an internal reset is generated, when the internal oscillator is selected. Rev. 1.00, 11/03, page 303 of 376 20.2.6 Power-Supply-Voltage Detection Circuit Characteristics Table 20.8 Power-Supply-Voltage Detection Circuit Characteristics VSS = 0.0 V, Ta = -20 to +75C, unless otherwise indicated. Test Condition LVDSEL = 0 LVDSEL = 0 LVDSEL = 0 LVDSEL = 1 Values Min. 3.3 3.6 2.0 3.0 1.0 50 LVDE = 1, BGRE = 1 Vcc = 5.0 V Typ. 3.7 4.0 2.3 3.6 -- -- -- Max. 4.2 4.5 2.7 4.2 -- -- TBD Unit V V V V V s A Item Power-supply falling detection voltage Power-supply rising detection voltage Reset detection voltage 1* Reset detection voltage 2* 1 2 Symbol Vint(D) Vint(U) Vreset1 Vreset2 VLVDRmin tLVDON Lower-limit voltage of LVDR 3 operation* LVD stabilization time Current consumption in standby ISTBY mode Notes: 1. This voltage should be used when the falling and rising voltage detection function is used. 2. Select the low-voltage reset 2 when only the low-voltage detection reset is used. 3. When the power-supply voltage (Vcc) falls below VLVDRmin = 1.0 V and then rises, a reset may not occur. Therefore sufficient evaluation is required. 20.2.7 LVDI External Voltage Detection Circuit Characteristics Table 20.9 LVDI External Voltage Detection Circuit Characteristics Vcc = 4.5 to 5.5 V, AVcc = 3.0 to 5.5 V, VSS= 0.0 V, Ta = -20 to +75C Test Condition Values Min. 0.85 VextD > VextU -0.3 Typ. 1.15 -- Max. 1.45 Unit V Item ExtD/ExtU input detection voltage ExtD/ExtU input voltage range Symbol Vexd VextD/U Lower voltage, V either AVcc + 0.3 or Vcc + 0.3 Rev. 1.00, 11/03, page 304 of 376 20.2.8 Power-On Reset Characteristics Table 20.10 Power-On Reset Circuit Characteristics VSS = 0.0 V, Ta = -20 to +75C, unless otherwise indicated. Test Condition Values Min. 100 -- Typ. 150 -- Max. -- 100 Unit k mV Item Pull-up resistance of RES pin Power-on reset start voltage* Note: * Symbol RRES Vpor The power-supply voltage (Vcc) must fall below Vpor = 100 mV and then rise after charge of the RES pin is removed completely. In order to remove charge of the RES pin, it is recommended that the diode be placed in the Vcc side. If the power-supply voltage (Vcc) rises from the point over 100 mV, a power-on reset may not occur. Rev. 1.00, 11/03, page 305 of 376 20.2.9 Flash Memory Characteristics Table 20.11 Flash Memory Characteristics VCC = 3.0 V to 5.5 V, VSS = 0.0 V, Ta = -20C to +75C, unless otherwise specified. Test Condition Values Min. -- -- 1 50 1n6 7 n 1000 28 198 Typ. 7 100 -- -- 30 200 10 -- -- -- -- -- -- -- Max. Unit -- -- -- -- 32 202 12 -- -- -- -- -- -- ms ms Times s s s s s s s s s s s Item Programming time (per 128 bytes)* * * Erase time (per block) * * * Reprogramming count Programming Wait time after SWE 1 bit setting* Wait time after PSU 1 bit setting* Wait time after P bit 14 setting* * 136 124 Symbol tP tE NWEC x y z1 z2 z3 Wait time after P bit 1 clear* Wait time after PSU 1 bit clear* Wait time after PV 1 bit setting* Wait time after 1 dummy write* Wait time after PV 1 bit clear* Wait time after SWE 1 bit clear* 1000 10000 -- Additional8 programming 5 5 4 2 2 100 -- Maximum N 145 programming count* * * 1000 Times Rev. 1.00, 11/03, page 306 of 376 Item Erase Wait time after SWE 1 bit setting* Wait time after ESU 1 bit setting* Wait time after E bit 16 setting* * Wait time after E bit 1 clear* Wait time after ESU 1 bit clear* Wait time after EV 1 bit setting* Wait time after 1 dummy write* Wait time after EV 1 bit clear* Wait time after SWE 1 bit clear* Maximum erase 167 count* * * Test Symbol Condition x y z N Values Min. 1 100 10 10 10 20 2 4 100 -- Typ. -- -- -- -- -- -- -- -- -- -- Max. -- -- 100 -- -- -- -- -- -- 120 Unit s s ms s s s s s s Times Notes: 1. Make the time settings in accordance with the program/erase algorithms. 2. The programming time for 64 bytes. (Indicates the total time for which the P bit in flash memory control register 1 (FLMCR1) is set. The program-verify time is not included.) 3. The time required to erase one block. (Indicates the time for which the E bit in flash memory control register 1 (FLMCR1) is set. The erase-verify time is not included.) 4. Programming time maximum value (tP (max.)) = wait time after P bit setting (z) x maximum programming count (N) 5. Set the maximum programming count (N) according to the actual set values of z1, z2, and z3, so that it does not exceed the programming time maximum value (tP (max.)). The wait time after P bit setting (z1, z2) should be changed as follows according to the value of the programming count (n). Programming count (n) 1n6 z1 = 30 s 7 n 1000 z2 = 200 s 6. Erase time maximum value (tE (max.)) = wait time after E bit setting (z) x maximum erase count (N) 7. Set the maximum erase count (N) according to the actual set value of (z), so that it does not exceed the erase time maximum value (tE (max.)). Rev. 1.00, 11/03, page 307 of 376 20.3 20.3.1 Electrical Characteristics (Masked ROM Version) Power Supply Voltage and Operating Ranges 1. Supply voltage and oscillation frequency range osc(MHz) 10.0 2.0 2.7 AVcc = 3.0 to 5.5 V Active mode Sleep mode 5.5 Vcc(V) 2. Power supply voltage and operating frequency range (MHz) 10.0 (kHz) 1250 2.0 31.25 2.7 5.5 Vcc(V) AVcc = 3.0 to 5.5 V Active mode Sleep mode (When MA2 = 0 in SYSCR2) 2.7 5.5 Vcc(V) AVcc = 3.0 to 5.5 V Active mode Sleep mode (When MA2 = 1 in SYSCR2) Rev. 1.00, 11/03, page 308 of 376 3. Analog power supply voltage and A/D converter accuracy guarantee range (MHz) 10.0 2.0 3.0 Vcc = 2.7 to 5.5 V Active mode Sleep mode 5.5 AVcc(V) Rev. 1.00, 11/03, page 309 of 376 20.3.2 DC Characteristics Table 20.12 DC Characteristics (1) VCC = 2.7 V to 5.5 V, VSS = 0.0 V, Ta = -20C to +75C unless otherwise indicated. Applicable Symbol Pins Test Condition Values Min. VCC x 0.8 VCC x 0.9 Typ. Max. -- -- VCC + 0.3 VCC + 0.3 Unit V V Notes Item Input high VIH voltage RES, NMI, WKP5, VCC = 4.0 V to 5.5 V IRQ0, IRQ3, ADTRG, TMRIV, TMCIV, FTCI, FTIOA to FTIOD, SCK3, TRGV RXD, SCL, SDA, VCC = 4.0 V to 5.5 V P17, P14, P22 to P20, P57 to P55, P76 to P74, P84 to P80, PC1, PC0 PB3 to PB0 AVCC = 4.0 V to 5.5 V AVCC = 3.0 V to 5.5 V OSC1 VCC = 4.0 V to 5.5 V VCC x 0.7 VCC x 0.8 -- -- VCC + 0.3 VCC + 0.3 V V AVCC x 0.7 -- AVCC x 0.8 -- VCC - 0.5 VCC - 0.3 -0.3 -- -- AVCC + 0.3 AVCC + 0.3 VCC + 0.3 VCC + 0.3 VCC x 0.2 V V V V V Input low voltage VIL RES, NMI, WKP5, VCC = 4.0 V to 5.5 V IRQ0, IRQ3, ADTRG, TMRIV, TMCIV, FTCI, FTIOA to FTIOD, SCK3, TRGV RXD, SCL, SDA, P17, P14, P22 to P20, P57 to P55, P76 to P74, P84 to P80, PC1, PC0 PB3 to PB0 OSC1 VCC = 4.0 V to 5.5 V -0.3 -- VCC x 0.1 V -0.3 -- VCC x 0.3 V -0.3 -- VCC x 0.2 V AVCC = 4.0 V to 5.5 V AVCC = 3.0 V to 5.5 V VCC = 4.0 V to 5.5 V -0.3 -0.3 -0.3 -0.3 -- -- -- -- AVCC x 0.3 V AVCC x 0.2 0.5 0.3 V V Rev. 1.00, 11/03, page 310 of 376 Item Output high voltage Symbol VOH Applicable Pins P17, P14, P22 to P20, P55, P76 to P74, P84 to P80, PC1, PC0 P56, P57 Test Condition -IOH = 5 mA Values Min. Typ. -- -- Max. -- -- Unit V V Notes VCC = 4.0 V to 5.5 V VCC - 1.0 -IOH = 0.1 mA VCC - 0.5 VCC = 4.0 V to 5.5 V VCC - 2.5 -I = 0.1 mA OH -- -- -- -- -- -- -- -- -- -- -- -- -- 0.6 0.4 1.5 1.0 0.4 0.4 0.6 0.4 1.0 V V V V V V V V V V A VCC = 2.7 V to 4.0 V VCC - 2.0 -I = 0.1 mA OH Output low VOL voltage P17, P14, P22 to P20, P57 to P55, P76 to P74, PC1, PC0 P84 to P80 VCC = 4.0 V to 5.5 V -- IOL = 1.6 mA IOL = 0.4 mA -- VCC = 4.0 V to 5.5 V -- IOL = 20.0 mA VCC = 4.0 V to 5.5 V -- IOL = 10.0 mA VCC = 4.0 V to 5.5 V -- IOL = 1.6 mA IOL = 0.4 mA -- SCL, SDA VCC = 4.0 V to 5.5 V -- IOL = 6.0 mA IOL = 3.0 mA -- -- Input/ output leakage current | IIL | OSC1, RES, NMI, VIN = 0.5 V to WKP5, (VCC - 0.5 V) IRQ0, IRQ3, ADTRG, TRGV, TMRIV, TMCIV, FTCI, FTIOA to FTIOD, RXD, SCK3, SCL, SDA P17, P14, P22 to P20, P57 to P55, P76 to P74, P84 to P80, PC1, PC0 PB3 to PB0 VIN = 0.5 V to (VCC - 0.5 V) -- -- 1.0 A VIN = 0.5 V to (AVCC - 0.5 V) -- -- 1.0 A Rev. 1.00, 11/03, page 311 of 376 Item Pull-up MOS current Input capacitance Symbol -Ip Applicable Pins P17, P14, P55 Test Condition VCC = 5.0 V, VIN = 0.0 V VCC = 3.0 V, VIN = 0.0 V Values Min. 50.0 -- -- Typ. -- 60.0 -- Max. 300.0 -- 15.0 Unit Notes A A pF Reference value Cin All input pins except power supply pins VCC f = 1 MHz, VIN = 0.0 V, Ta = 25C Active mode 1 VCC = 5.0 V, fOSC = 10 MHz Active mode 1 VCC = 3.0 V, fOSC = 10 MHz Active IOPE1 mode current consumption IOPE2 -- TBD TBD mA * -- TBD -- mA Reference value* * VCC Active mode 2 VCC = 5.0 V, fOSC = 10 MHz Active mode 2 VCC = 3.0 V, fOSC = 10 MHz -- TBD TBD mA -- TBD -- mA Reference value* * Sleep ISLEEP1 mode current consumption ISLEEP2 VCC Sleep mode 1 VCC = 5.0 V, fOSC = 10 MHz Sleep mode 1 VCC = 3.0 V, fOSC = 10 MHz -- TBD TBD mA -- TBD -- mA Reference value* * VCC Sleep mode 2 VCC = 5.0 V, fOSC = 10 MHz Sleep mode 2 VCC = 3.0 V, fOSC = 10 MHz -- TBD TBD mA -- TBD -- mA Reference value* Subsleep ISUBSP mode current consumption ISTBY Standby mode current consumption RAM data VRAM retaining voltage VCC VCC = 3.0 V -- -- TBD A VCC -- -- TBD A * VCC 2.0 -- -- V Rev. 1.00, 11/03, page 312 of 376 Note: * Pin states during current consumption measurement are given below (excluding current in the pull-up MOS transistors and output buffers). RES Pin VCC VCC VCC Internal State Operates Operates (/64) Only timers operate Only timers operate (/64) CPU and timers both stop VCC System clock: Internal RC oscillator VCC Other Pins VCC Oscillator Pins System clock: Internal RC oscillator Mode Active mode 1 Active mode 2 Sleep mode 1 Sleep mode 2 Standby mode Rev. 1.00, 11/03, page 313 of 376 Table 20.12 DC Characteristics (2) VCC = 3.0 V to 5.5 V, VSS = 0.0 V, Ta = -20C to +75C, unless otherwise indicated. Application Pins Output pins except P84 to P80, SCL, and SDA P84 to P80 Output pins except P84 to P80, SCL, and SDA P84 to P80 SCL, SDA Allowable output low IOL current (total) Output pins except P84 to P80, SCL, and SDA P84 to P80, SCL, and SDA Output pins except P84 to P80, SCL, and SDA P84 to P80, SCL, and SDA Allowable output high I -IOH I current (per pin) Output pins except P56, P57 P56, P57 Allowable output high I -IOH I current (total) All output pins Test Condition Values Min. Typ. -- Max. 2.0 Unit mA Item Symbol Allowable output low IOL current (per pin) VCC = 4.0 V to 5.5 V -- -- -- -- -- 20.0 0.5 mA mA -- -- VCC = 4.0 V to 5.5 V -- -- -- -- 10.0 6.0 40.0 mA mA mA -- -- -- -- 80.0 20.0 mA mA -- VCC = 4.0 V to 5.5 V -- -- VCC = 4.0 V to 5.5 V -- -- VCC = 4.0 V to 5.5 V -- -- -- -- -- -- -- -- -- 40.0 5.0 0.2 2.0 0.2 8.0 mA mA mA mA mA mA T.B.D mA Rev. 1.00, 11/03, page 314 of 376 20.3.3 AC Characteristics Table 20.13 AC Characteristics VCC = 2.7 V to 5.5 V, VSS = 0.0 V, Ta = -20C to +75C, unless otherwise specified. Applicable Pins OSC1, OSC2 Test Condition Values Min. 2.0 Typ. -- Max. 10.0 Unit MHz Reference Figure *1 Item System clock oscillation frequency System clock () cycle time Instruction cycle time Oscillation stabilization time (crystal resonator) Symbol fOSC tcyc 1 -- 2 -- -- -- -- 64 32.0 -- 10.0 tOSC s tcyc ms *2 trc OSC1, OSC2 -- Oscillation trc stabilization time (ceramic resonator) External clock high tCPH width External clock low width External clock rise time External clock fall time RES pin low width tCPL tCPr tCPf tREL OSC1, OSC2 -- -- 5.0 ms OSC1 OSC1 OSC1 OSC1 RES At power-on and in modes other than those below 40.0 40.0 -- -- TBD -- -- -- -- -- -- -- 15.0 15.0 -- ns ns ns ns ns Figure 20.1 Figure 20.2 In active mode TBD and sleep mode operation Input pin high width tIH IRQ0 , IRQ3, WKP5, NMI, TMCIV, TMRIV, TRGV, ADTRG, FTCI, FTIOA to FTIOD IRQ0, IRQ3, WKP5, NMI, TMCIV, TMRIV, TRGV, ADTRG, FTCI, FTIOA to FTIOD 2 -- -- ns -- -- tcyc Figure 20.3 Input pin low width tIL 2 -- -- tcyc Rev. 1.00, 11/03, page 315 of 376 Notes: 1. When an external clock is input, the minimum system clock oscillator frequency is 2.0 MHz. 2. Determined by MA2 to MA0 in system control register 2 (SYSCR2). Table 20.14 I2C Bus Interface Timing VCC = 3.0 to 5.5 V, VSS = 0.0 V, Ta = -20 to +75C, unless otherwise indicated. Applicable Pins Test Condition Min. Values Typ. Reference Max. Unit Figure Item Symbol SCL input cycle time SCL input high pulse width SCL input low pulse width SCL and SDA input fall time SCL and SDA input spike pulse removal time SDA input bus-free time Start condition input hold time Retransmission start condition input setup time Setup time for stop condition input Data input setup time Data input hold time Capacitive load of SCL and SDA SCL and SDA output fall time tSCL tSCLH tSCLL tSf tSP 12tcyc + 600 ns ns ns Figure 20.4 3tcyc + 300 5tcyc + 300 300 ns 1tcyc ns tBUF tSTAH tSTAS 5tcyc 3tcyc 3tcyc ns ns ns tSTOS tSDAS tSDAH cb tSf VCC = 4.0 to 5.5 V 3tcyc 1tcyc+ 20 0 0 ns ns ns 400 pF 250 ns 300 ns Rev. 1.00, 11/03, page 316 of 376 Table 20.15 Serial Interface (SCI3) Timing VCC = 2.7 V to 5.5 V, VSS = 0.0 V, Ta = -20C to +75C, unless otherwise specified. Applicable Pins Test Condition Values Min. Typ. Max. Unit Reference Figure Item Symbol Input clock cycle Asynchronous Clocked synchronous Tscyc SCK3 4 6 -- -- -- -- -- -- 0.6 1 tcyc tcyc Tscyc tcyc Figure 20.5 Input clock pulse width tSCKW Transmit data delay time (clocked synchronous) Receive data setup time (clocked synchronous)s Receive data hold time (clocked synchronous) tTXD SCK3 TXD 0.4 -- Figure 20.6 tRXS RXD 100.0 -- -- ns tRXH RXD 100.0 -- -- ns Rev. 1.00, 11/03, page 317 of 376 20.3.4 A/D Converter Characteristics Table 20.16 A/D Converter Characteristics VCC = 3.0 V to 5.5 V, VSS = 0.0 V, Ta = -20C to +75C, unless otherwise specified. Applicable Symbol Pins AVCC AVIN AIOPE AVCC AN3 to AN0 AVCC Test Condition Values Min. 3.0 VSS - 0.3 AVCC = 5.0 V -- fOSC = 10 MHz AISTOP1 AVCC -- 50 -- A *2 Reference value *3 Typ. Max. VCC -- -- 5.5 Unit V Notes *1 Item Analog power supply voltage Analog input voltage Analog power supply current AVCC + 0.3 V 2.0 mA AISTOP2 Analog input capacitance Allowable signal source impedance Resolution (data length) Conversion time (single mode) Nonlinearity error Offset error Full-scale error Quantization error Absolute accuracy Conversion time (single mode) Nonlinearity error Offset error Full-scale error Quantization error Absolute accuracy CAIN RAIN AVCC AN3 to AN0 AN3 to AN0 -- -- -- 10 AVCC = 3.0 V 134 to 5.5 V -- -- -- -- -- AVCC = 4.0 V 70 to 5.5 V -- -- -- -- -- -- -- -- 10 -- -- -- -- -- -- -- -- -- -- -- -- 5.0 30.0 5.0 10 -- 7.5 7.5 7.5 0.5 8.0 -- 7.5 7.5 7.5 0.5 8.0 A pF k bit tcyc LSB LSB LSB LSB LSB tcyc LSB LSB LSB LSB LSB Rev. 1.00, 11/03, page 318 of 376 Item Conversion time (single mode) Nonlinearity error Offset error Full-scale error Quantization error Absolute accuracy Symbol Applicable Test Pins Condition Values Min. Typ. -- -- -- -- -- -- Max. -- 3.5 3.5 3.5 0.5 4.0 Unit tcyc LSB LSB LSB LSB LSB Notes AVCC = 4.0 V 134 to 5.5 V -- -- -- -- -- Notes: 1. Set AVCC = VCC when the A/D converter is not used. 2. AISTOP1 is the current in active and sleep modes while the A/D converter is idle. 3. AISTOP2 is the current at reset and in standby and subsleep modes while the A/D converter is idle. 20.3.5 Watchdog Timer Characteristics Table 20.17 Watchdog Timer Characteristics VCC = 2.7 V to 5.5 V, VSS = 0.0 V, Ta = -20C to +75C, unless otherwise specified. Applicable Test Condition Min. Pins 0.2 Values Typ. 0.4 Max. Unit Notes -- s * Item Internal oscillator overflow time Note: * Symbol tOVF Shows the time to count from 0 to 255, at which point an internal reset is generated, when the internal oscillator is selected. Rev. 1.00, 11/03, page 319 of 376 20.3.6 Power-Supply-Voltage Detection Circuit Characteristics Table 20.18 Power-Supply-Voltage Detection Circuit Characteristics VSS = 0.0 V, Ta = -20 to +75C, unless otherwise indicated. Test Condition Values Min. Typ. 3.7 4.0 2.3 3.6 -- -- -- Max. 4.2 4.5 2.7 4.2 -- -- TBD Unit V V V V V s A Item Power-supply falling detection voltage Power-supply rising detection voltage Reset detection voltage 1* Reset detection voltage 2* 1 2 Symbol Vint(D) Vint(U) Vreset1 Vreset2 VLVDRmin tLVDON ISTBY LVDSEL = 0 3.3 LVDSEL = 0 3.6 LVDSEL = 0 2.0 LVDSEL = 1 3.0 1.0 50 LVDE = 1, BGRE = 1 Vcc = 5.0 V Lower-limit voltage of LVDR 3 operation* LVD stabilization time Current consumption in standby mode Notes: 1. This voltage should be used when the falling and rising voltage detection function is used. 2. Select the low-voltage reset 2 when only the low-voltage detection reset is used. 3. When the power-supply voltage (Vcc) falls below VLVDRmin = 1.0 V and then rises, a reset may not occur. Therefore sufficient evaluation is required. 20.3.7 LVDI External Voltage Detection Circuit Characteristics Table 20.19 LVDI External Voltage Detection Circuit Characteristics Vcc = 4.5 to 5.5 V, AVcc = 3.0 to 5.5 V, VSS= 0.0 V, Ta = -20 to +75C Test Condition Values Min. 0.85 VextD > VextU -0.3 Typ. 1.15 -- Max. 1.45 Unit V Item ExtD/ExtU input detection voltage ExtD/ExtU input voltage range Symbol Vexd VextD/U Lower voltage, V either AVcc + 0.3 or Vcc + 0.3 Rev. 1.00, 11/03, page 320 of 376 20.3.8 Power-On Reset Characteristics Table 20.20 Power-On Reset Circuit Characteristics VSS = 0.0 V, Ta = -20 to +75C, unless otherwise indicated. Test Condition Values Min. 100 -- Typ. 150 -- Max. -- 100 Unit k mV Item Pull-up resistance of RES pin Power-on reset start voltage* Note: * Symbol RRES Vpor The power-supply voltage (Vcc) must fall below Vpor = 100 mV and then rise after charge of the RES pin is removed completely. In order to remove charge of the RES pin, it is recommended that the diode be placed in the Vcc side. If the power-supply voltage (Vcc) rises from the point over 100 mV, a power-on reset may not occur. Rev. 1.00, 11/03, page 321 of 376 20.4 Operation Timing tOSC OSC1 VIH VIL tCPH tCPr tCPL tCPf Figure 20.1 System Clock Input Timing Vcc Vcc 0.7 OSC1 tREL VIL VIL tREL Figure 20.2 RES Low Width Timing , VIH VIL tIL tIH FTCI, FTIOA FTIOB, FTIOC FTIOD TMCIV, TMRIV TRGV Figure 20.3 Input Timing Rev. 1.00, 11/03, page 322 of 376 SDA tBUF VIH VIL tSTAH tSCLH tSTAS tSP tSTOS SCL P* S* tSf tSCLL tSCL Sr* tSr tSDAH tSDAS P* Note: * S, P, and Sr represent the following: S: Start condition P: Stop comdition Sr: Retransmission start condition Figure 20.4 I2C Bus Interface Input/Output Timing tSCKW SCK3 tscyc Figure 20.5 SCK3 Input Clock Timing Rev. 1.00, 11/03, page 323 of 376 t scyc SCK3 VIH or VOH * VIL or VOL * t TXD TXD (transmit data) VOH* VOL * t RXS t RXH RXD (receive data) Note: * Output timing reference levels Output high: Output low: VOH = 2.0 V VOL= 0.8 V Load conditions are shown in figure 20.7. Figure 20.6 SCI3 Input/Output Timing in Clocked Synchronous Mode 20.5 Output Load Condition VCC 2.4 k LSI output pin 30 pF 12 k Figure 20.7 Output Load Circuit Rev. 1.00, 11/03, page 324 of 376 Appendix A Instruction Set A.1 Symbol Rd Rs Rn ERd ERs ERn (EAd) (EAs) PC SP CCR N Z V C disp + - x / ( ), < > Instruction List Description General (destination*) register General (source*) register General register* General destination register (address register or 32-bit register) General source register (address register or 32-bit register) General register (32-bit register) Destination operand Source operand Program counter Stack pointer Condition-code register N (negative) flag in CCR Z (zero) flag in CCR V (overflow) flag in CCR C (carry) flag in CCR Displacement Transfer from the operand on the left to the operand on the right, or transition from the state on the left to the state on the right Addition of the operands on both sides Subtraction of the operand on the right from the operand on the left Multiplication of the operands on both sides Division of the operand on the left by the operand on the right Logical AND of the operands on both sides Logical OR of the operands on both sides Logical exclusive OR of the operands on both sides NOT (logical complement) Contents of operand * Operand Notation Note: General registers include 8-bit registers (R0H to R7H and R0L to R7L) and 16-bit registers (R0 to R7 and E0 to E7). Rev. 1.00, 11/03, page 325 of 376 * Condition Code Notation Symbol Description Changed according to execution result Undetermined (no guaranteed value) Cleared to 0 Set to 1 Not affected by execution of the instruction Varies depending on conditions, described in notes * 0 1 -- Rev. 1.00, 11/03, page 326 of 376 Table A.1 Instruction Set * Data transfer instructions Addressing Mode and Instruction Length (bytes) @-ERn/@ERn+ Operand Size Condition Code No. of States*1 @(d, ERn) I H N Z V C MOV MOV.B #xx:8, Rd MOV.B Rs, Rd MOV.B @ERs, Rd MOV.B @(d:16, ERs), Rd MOV.B @(d:24, ERs), Rd MOV.B @ERs+, Rd B B B B B B 2 2 2 4 8 2 ---- ---- ---- ---- ---- ---- #xx:8 Rd8 Rs8 Rd8 @ERs Rd8 @(d:16, ERs) Rd8 @(d:24, ERs) Rd8 @ERs Rd8 ERs32+1 ERs32 2 4 6 2 4 8 2 @aa:8 Rd8 @aa:16 Rd8 @aa:24 Rd8 Rs8 @ERd Rs8 @(d:16, ERd) Rs8 @(d:24, ERd) ERd32-1 ERd32 Rs8 @ERd 2 4 6 Rs8 @aa:8 Rs8 @aa:16 Rs8 @aa:24 #xx:16 Rd16 2 2 4 8 2 Rs16 Rd16 @ERs Rd16 @(d:16, ERs) Rd16 @(d:24, ERs) Rd16 @ERs Rd16 ERs32+2 @ERd32 4 6 2 4 8 @aa:16 Rd16 @aa:24 Rd16 Rs16 @ERd Rs16 @(d:16, ERd) Rs16 @(d:24, ERd) 0-- 0-- 0-- 0-- 0-- 0-- 2 2 4 6 10 6 MOV.B @aa:8, Rd MOV.B @aa:16, Rd MOV.B @aa:24, Rd MOV.B Rs, @ERd MOV.B Rs, @(d:16, ERd) MOV.B Rs, @(d:24, ERd) MOV.B Rs, @-ERd B B B B B B B ---- ---- ---- ---- ---- ---- ---- 0-- 0-- 0-- 0-- 0-- 0-- 0-- 4 6 8 4 6 10 6 MOV.B Rs, @aa:8 MOV.B Rs, @aa:16 MOV.B Rs, @aa:24 MOV.W #xx:16, Rd MOV.W Rs, Rd MOV.W @ERs, Rd B B B W4 W W ---- ---- ---- ---- ---- ---- ---- ---- ---- 0-- 0-- 0-- 0-- 0-- 0-- 0-- 0-- 0-- 4 6 8 4 2 4 6 10 6 MOV.W @(d:16, ERs), Rd W MOV.W @(d:24, ERs), Rd W MOV.W @ERs+, Rd W MOV.W @aa:16, Rd MOV.W @aa:24, Rd MOV.W Rs, @ERd W W W ---- ---- ---- ---- ---- 0-- 0-- 0-- 0-- 0-- 6 8 4 6 10 MOV.W Rs, @(d:16, ERd) W MOV.W Rs, @(d:24, ERd) W Rev. 1.00, 11/03, page 327 of 376 Advanced Mnemonic Operation @(d, PC) Normal @@aa @ERn @aa #xx Rn -- Addressing Mode and Instruction Length (bytes) @-ERn/@ERn+ Operand Size Condition Code No. of States*1 @(d, ERn) I H N Z V C MOV MOV.W Rs, @-ERd MOV.W Rs, @aa:16 MOV.W Rs, @aa:24 MOV.L #xx:32, Rd MOV.L ERs, ERd MOV.L @ERs, ERd MOV.L @(d:16, ERs), ERd MOV.L @(d:24, ERs), ERd MOV.L @ERs+, ERd W 2 ERd32-2 ERd32 Rs16 @ERd 4 6 Rs16 @aa:16 Rs16 @aa:24 #xx:32 Rd32 ERs32 ERd32 ---- 0-- 6 W W L L L L L L 6 2 4 6 10 4 ---- ---- ---- ---- ---- ---- ---- ---- 0-- 0-- 0-- 0-- 0-- 0-- 0-- 0-- 6 8 6 2 8 10 14 10 @ERs ERd32 @(d:16, ERs) ERd32 @(d:24, ERs) ERd32 @ERs ERd32 ERs32+4 ERs32 6 8 @aa:16 ERd32 @aa:24 ERd32 ERs32 @ERd 6 10 4 ERs32 @(d:16, ERd) ERs32 @(d:24, ERd) ERd32-4 ERd32 ERs32 @ERd 6 8 ERs32 @aa:16 ERs32 @aa:24 2 @SP Rn16 SP+2 SP 4 @SP ERn32 SP+4 SP 2 SP-2 SP Rn16 @SP 4 SP-4 SP ERn32 @SP Cannot be used in this LSI Cannot be used in this LSI MOV.L @aa:16, ERd MOV.L @aa:24, ERd MOV.L ERs, @ERd MOV.L ERs, @(d:16, ERd) MOV.L ERs, @(d:24, ERd) MOV.L ERs, @-ERd L L L L L L 4 ---- ---- ---- ---- ---- ---- 0-- 0-- 0-- 0-- 0-- 0-- 10 12 8 10 14 10 MOV.L ERs, @aa:16 MOV.L ERs, @aa:24 POP POP.W Rn POP.L ERn L L W ---- ---- ---- 0-- 0-- 0-- 10 12 6 L ---- 0-- 10 PUSH PUSH.W Rn PUSH.L ERn W ---- 0-- 6 L ---- 0-- 10 MOVFPE MOVFPE @aa:16, Rd B 4 Cannot be used in this LSI Cannot be used in this LSI MOVTPE MOVTPE Rs, @aa:16 B 4 Rev. 1.00, 11/03, page 328 of 376 Advanced Mnemonic Operation @(d, PC) Normal @@aa @ERn @aa #xx Rn -- * Arithmetic instructions Addressing Mode and Instruction Length (bytes) @-ERn/@ERn+ Operand Size Condition Code No. of States*1 @(d, ERn) I H N Z V C ADD ADD.B #xx:8, Rd ADD.B Rs, Rd ADD.W #xx:16, Rd ADD.W Rs, Rd ADD.L #xx:32, ERd B B 2 2 -- -- Rd8+#xx:8 Rd8 Rd8+Rs8 Rd8 Rd16+#xx:16 Rd16 2 Rd16+Rs16 Rd16 ERd32+#xx:32 ERd32 2 ERd32+ERs32 ERd32 Rd8+#xx:8 +C Rd8 2 2 2 2 2 2 2 2 2 2 Rd8+Rs8 +C Rd8 ERd32+1 ERd32 ERd32+2 ERd32 ERd32+4 ERd32 Rd8+1 Rd8 Rd16+1 Rd16 Rd16+2 Rd16 ERd32+1 ERd32 ERd32+2 ERd32 Rd8 decimal adjust Rd8 Rd8-Rs8 Rd8 Rd16-#xx:16 Rd16 2 Rd16-Rs16 Rd16 2 2 4 2 6 W4 W L 6 -- (1) -- (1) -- (2) ADD.L ERs, ERd L -- (2) 2 ADDX ADDX.B #xx:8, Rd ADDX.B Rs, Rd ADDS ADDS.L #1, ERd ADDS.L #2, ERd ADDS.L #4, ERd INC INC.B Rd INC.W #1, Rd INC.W #2, Rd INC.L #1, ERd INC.L #2, ERd DAA SUB DAA Rd B B L L L B W W L L B 2 -- -- (3) (3) 2 2 2 2 2 2 2 2 2 2 2 ------------ ------------ ------------ ---- ---- ---- ---- ---- --* -- -- -- -- -- *-- SUB.B Rs, Rd SUB.W #xx:16, Rd SUB.W Rs, Rd SUB.L #xx:32, ERd SUB.L ERs, ERd B W4 W L L B B L L L B W W 2 6 2 -- 2 4 2 6 2 2 2 2 2 2 2 2 2 -- (1) -- (1) ERd32-#xx:32 ERd32 -- (2) 2 ERd32-ERs32 ERd32 -- (2) SUBX SUBX.B #xx:8, Rd SUBX.B Rs, Rd SUBS SUBS.L #1, ERd SUBS.L #2, ERd SUBS.L #4, ERd DEC DEC.B Rd DEC.W #1, Rd DEC.W #2, Rd Rd8-#xx:8-C Rd8 2 2 2 2 2 2 2 Rd8-Rs8-C Rd8 ERd32-1 ERd32 ERd32-2 ERd32 ERd32-4 ERd32 Rd8-1 Rd8 Rd16-1 Rd16 Rd16-2 Rd16 -- -- (3) (3) ------------ ------------ ------------ ---- ---- ---- -- -- -- Rev. 1.00, 11/03, page 329 of 376 Advanced Mnemonic Operation @(d, PC) Normal @@aa @ERn @aa #xx Rn -- Addressing Mode and Instruction Length (bytes) @-ERn/@ERn+ Operand Size Condition Code No. of States*1 @(d, ERn) I H N Z V C DEC DEC.L #1, ERd DEC.L #2, ERd DAS DAS.Rd L L B 2 2 2 ---- ---- --* ERd32-1 ERd32 ERd32-2 ERd32 Rd8 decimal adjust Rd8 Rd8 x Rs8 Rd16 (unsigned multiplication) Rd16 x Rs16 ERd32 (unsigned multiplication) Rd8 x Rs8 Rd16 (signed multiplication) Rd16 x Rs16 ERd32 (signed multiplication) Rd16 / Rs8 Rd16 (RdH: remainder, RdL: quotient) (unsigned division) ERd32 / Rs16 ERd32 (Ed: remainder, Rd: quotient) (unsigned division) Rd16 / Rs8 Rd16 (RdH: remainder, RdL: quotient) (signed division) ERd32 / Rs16 ERd32 (Ed: remainder, Rd: quotient) (signed division) Rd8-#xx:8 -- -- 2 2 2 *-- MULXU MULXU. B Rs, Rd B 2 ------------ 14 MULXU. W Rs, ERd W 2 ------------ 22 MULXS MULXS. B Rs, Rd B 4 ---- ---- 16 MULXS. W Rs, ERd W 4 ---- ---- 24 DIVXU DIVXU. B Rs, Rd B 2 -- -- (6) (7) -- -- 14 DIVXU. W Rs, ERd W 2 -- -- (6) (7) -- -- 22 DIVXS DIVXS. B Rs, Rd B 4 -- -- (8) (7) -- -- 16 DIVXS. W Rs, ERd W 4 -- -- (8) (7) -- -- 24 CMP CMP.B #xx:8, Rd CMP.B Rs, Rd CMP.W #xx:16, Rd CMP.W Rs, Rd CMP.L #xx:32, ERd CMP.L ERs, ERd B B 2 2 -- -- 2 2 4 2 4 2 Rd8-Rs8 Rd16-#xx:16 W4 W L L 6 2 2 -- (1) -- (1) -- (2) -- (2) Rd16-Rs16 ERd32-#xx:32 ERd32-ERs32 Rev. 1.00, 11/03, page 330 of 376 Advanced Mnemonic Operation @(d, PC) Normal @@aa @ERn @aa #xx Rn -- Addressing Mode and Instruction Length (bytes) @-ERn/@ERn+ Operand Size Condition Code No. of States*1 @(d, ERn) I H N Z V C NEG NEG.B Rd NEG.W Rd NEG.L ERd EXTU EXTU.W Rd EXTU.L ERd 2 2 2 2 -- -- -- B 0-Rd8 Rd8 W 0-Rd16 Rd16 L 0-ERd32 ERd32 W 0 ( 2 2 2 2 ---- 0 0-- 2 ---- 0 0-- 2 EXTS EXTS.W Rd EXTS.L ERd 2 ---- 0-- 2 2 ---- 0-- 2 Rev. 1.00, 11/03, page 331 of 376 Advanced Mnemonic Operation @ERn @(d, PC) Normal @@aa @aa #xx Rn -- * Logic instructions Addressing Mode and Instruction Length (bytes) @-ERn/@ERn+ Operand Size Condition Code No. of States*1 @(d, ERn) I H N Z V C AND AND.B #xx:8, Rd AND.B Rs, Rd AND.W #xx:16, Rd AND.W Rs, Rd AND.L #xx:32, ERd AND.L ERs, ERd B B 2 2 ---- ---- ---- ---- Rd8#xx:8 Rd8 Rd8Rs8 Rd8 Rd16#xx:16 Rd16 2 Rd16Rs16 Rd16 0-- 0-- 0-- 0-- 0-- 0-- 0-- 0-- 0-- 0-- 0-- 0-- 0-- 0-- 0-- 0-- 0-- 0-- 0-- 0-- 0-- 2 2 4 2 6 4 2 2 4 2 6 4 2 2 4 2 6 4 2 2 2 W4 W L L B B W4 W L L B B W4 W L L B W L 6 4 2 2 2 2 2 2 6 4 2 2 2 6 4 ERd32#xx:32 ERd32 -- -- ERd32ERs32 ERd32 -- -- Rd8#xx:8 Rd8 Rd8Rs8 Rd8 Rd16#xx:16 Rd16 Rd16Rs16 Rd16 ERd32#xx:32 ERd32 ERd32ERs32 ERd32 Rd8#xx:8 Rd8 Rd8Rs8 Rd8 Rd16#xx:16 Rd16 Rd16Rs16 Rd16 ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- OR OR.B #xx:8, Rd OR.B Rs, Rd OR.W #xx:16, Rd OR.W Rs, Rd OR.L #xx:32, ERd OR.L ERs, ERd XOR XOR.B #xx:8, Rd XOR.B Rs, Rd XOR.W #xx:16, Rd XOR.W Rs, Rd XOR.L #xx:32, ERd XOR.L ERs, ERd ERd32#xx:32 ERd32 -- -- ERd32ERs32 ERd32 -- -- Rd8 Rd8 Rd16 Rd16 Rd32 Rd32 ---- ---- ---- NOT NOT.B Rd NOT.W Rd NOT.L ERd Rev. 1.00, 11/03, page 332 of 376 Advanced Mnemonic Operation @(d, PC) Normal @@aa @ERn #xx Rn @aa -- * Shift instructions Addressing Mode and Instruction Length (bytes) @-ERn/@ERn+ Operand Size Condition Code No. of States*1 @(d, ERn) I H N Z V C SHAL SHAL.B Rd SHAL.W Rd SHAL.L ERd SHAR SHAR.B Rd SHAR.W Rd SHAR.L ERd SHLL SHLL.B Rd SHLL.W Rd SHLL.L ERd SHLR SHLR.B Rd SHLR.W Rd SHLR.L ERd ROTXL ROTXL.B Rd B W L B W L B W L B W L B W L B W L B W L B W L 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 C MSB LSB C MSB C MSB 0 MSB C MSB LSB C MSB C MSB LSB LSB LSB LSB LSB 0 ---- ---- ---- ---- ---- ---- ---- 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ---- ---- ---- C ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ROTXL.W Rd ROTXL.L ERd ROTXR ROTXR.B Rd ROTXR.W Rd ROTXR.L ERd ROTL ROTL.B Rd ROTL.W Rd ROTL.L ERd ROTR ROTR.B Rd ROTR.W Rd ROTR.L ERd C MSB LSB ---- ---- Rev. 1.00, 11/03, page 333 of 376 Advanced Mnemonic Operation @(d, PC) Normal @@aa @ERn @aa #xx Rn -- * Bit manipulation instructions Addressing Mode and Instruction Length (bytes) @-ERn/@ERn+ Operand Size Condition Code No. of States*1 @(d, ERn) I H N Z V C BSET BSET #xx:3, Rd BSET #xx:3, @ERd BSET #xx:3, @aa:8 BSET Rn, Rd BSET Rn, @ERd BSET Rn, @aa:8 BCLR BCLR #xx:3, Rd BCLR #xx:3, @ERd BCLR #xx:3, @aa:8 BCLR Rn, Rd BCLR Rn, @ERd BCLR Rn, @aa:8 BNOT BNOT #xx:3, Rd B B B B B B B B B B B B B 2 4 4 2 4 4 2 4 4 2 4 4 2 (#xx:3 of Rd8) 1 (#xx:3 of @ERd) 1 (#xx:3 of @aa:8) 1 (Rn8 of Rd8) 1 (Rn8 of @ERd) 1 (Rn8 of @aa:8) 1 (#xx:3 of Rd8) 0 (#xx:3 of @ERd) 0 (#xx:3 of @aa:8) 0 (Rn8 of Rd8) 0 (Rn8 of @ERd) 0 (Rn8 of @aa:8) 0 (#xx:3 of Rd8) (#xx:3 of Rd8) 4 (#xx:3 of @ERd) (#xx:3 of @ERd) 4 (#xx:3 of @aa:8) (#xx:3 of @aa:8) (Rn8 of Rd8) (Rn8 of Rd8) 4 (Rn8 of @ERd) (Rn8 of @ERd) 4 (Rn8 of @aa:8) (Rn8 of @aa:8) (#xx:3 of Rd8) Z 4 4 (#xx:3 of @ERd) Z (#xx:3 of @aa:8) Z (Rn8 of @Rd8) Z 4 4 (Rn8 of @ERd) Z (Rn8 of @aa:8) Z (#xx:3 of Rd8) C ------------ ------------ ------------ ------------ ------------ ------------ ------------ ------------ ------------ ------------ ------------ ------------ ------------ 2 8 8 2 8 8 2 8 8 2 8 8 2 BNOT #xx:3, @ERd B ------------ 8 BNOT #xx:3, @aa:8 B ------------ 8 BNOT Rn, Rd B 2 ------------ 2 BNOT Rn, @ERd B ------------ 8 BNOT Rn, @aa:8 B ------------ 8 BTST BTST #xx:3, Rd BTST #xx:3, @ERd BTST #xx:3, @aa:8 BTST Rn, Rd BTST Rn, @ERd BTST Rn, @aa:8 BLD BLD #xx:3, Rd B B B B B B B 2 ------ ------ ------ ------ ------ ------ ---- ---- ---- ---- ---- ---- 2 6 6 2 6 6 2 2 2 ---------- Rev. 1.00, 11/03, page 334 of 376 Advanced Mnemonic Operation @(d, PC) Normal @@aa @ERn @aa #xx Rn -- Addressing Mode and Instruction Length (bytes) @-ERn/@ERn+ Operand Size Condition Code No. of States*1 @(d, ERn) I H N Z V C BLD BLD #xx:3, @ERd BLD #xx:3, @aa:8 B B B B B B B B B B B B B B B B B B B B B B B B B B B B B 2 2 2 2 2 2 2 2 2 4 4 ---------- ---------- ---------- ---------- ---------- (#xx:3 of @ERd) C (#xx:3 of @aa:8) C (#xx:3 of Rd8) C (#xx:3 of @ERd) C 4 (#xx:3 of @aa:8) C C (#xx:3 of Rd8) C (#xx:3 of @ERd24) 4 C (#xx:3 of @aa:8) C (#xx:3 of Rd8) C (#xx:3 of @ERd24) 4 C (#xx:3 of @aa:8) C(#xx:3 of Rd8) C C(#xx:3 of @ERd24) C 4 C(#xx:3 of @aa:8) C C (#xx:3 of Rd8) C C (#xx:3 of @ERd24) C 4 C (#xx:3 of @aa:8) C C(#xx:3 of Rd8) C C(#xx:3 of @ERd24) C 4 C(#xx:3 of @aa:8) C C (#xx:3 of Rd8) C C (#xx:3 of @ERd24) C 4 C (#xx:3 of @aa:8) C C(#xx:3 of Rd8) C C(#xx:3 of @ERd24) C 4 C(#xx:3 of @aa:8) C C (#xx:3 of Rd8) C 6 6 2 6 6 2 8 8 2 8 8 2 6 6 2 6 6 2 6 6 2 6 6 2 6 6 2 6 6 BILD BILD #xx:3, Rd BILD #xx:3, @ERd BILD #xx:3, @aa:8 BST BST #xx:3, Rd BST #xx:3, @ERd BIST BST #xx:3, @aa:8 BIST #xx:3, Rd BIST #xx:3, @ERd BIST #xx:3, @aa:8 BAND BAND #xx:3, Rd BAND #xx:3, @ERd BIAND BAND #xx:3, @aa:8 BIAND #xx:3, Rd BIAND #xx:3, @ERd BIAND #xx:3, @aa:8 BOR BOR #xx:3, Rd BOR #xx:3, @ERd BOR #xx:3, @aa:8 BIOR BIOR #xx:3, Rd BIOR #xx:3, @ERd BIOR #xx:3, @aa:8 BXOR BXOR #xx:3, Rd BXOR #xx:3, @ERd BXOR #xx:3, @aa:8 BIXOR BIXOR #xx:3, Rd BIXOR #xx:3, @ERd BIXOR #xx:3, @aa:8 4 ------------ ------------ ------------ ------------ ------------ ------------ ---------- ---------- ---------- ---------- ---------- ---------- ---------- ---------- ---------- ---------- ---------- ---------- ---------- ---------- ---------- ---------- 4 4 4 4 4 4 4 4 4 C (#xx:3 of @ERd24) C -- -- -- -- -- C (#xx:3 of @aa:8) C ---------- Rev. 1.00, 11/03, page 335 of 376 Advanced Mnemonic Operation @(d, PC) Normal @@aa @ERn @aa #xx Rn -- * Branching instructions Addressing Mode and Instruction Length (bytes) @-ERn/@ERn+ Operand Size Condition Code No. of States*1 @(d, ERn) Branch Condition If condition Always is true then PC PC+d Never else next; CZ=0 CZ=1 C=0 I H N Z V C Bcc BRA d:8 (BT d:8) BRA d:16 (BT d:16) BRN d:8 (BF d:8) BRN d:16 (BF d:16) BHI d:8 BHI d:16 BLS d:8 BLS d:16 BCC d:8 (BHS d:8) BCC d:16 (BHS d:16) BCS d:8 (BLO d:8) BCS d:16 (BLO d:16) BNE d:8 BNE d:16 BEQ d:8 BEQ d:16 BVC d:8 BVC d:16 BVS d:8 BVS d:16 BPL d:8 BPL d:16 BMI d:8 BMI d:16 BGE d:8 BGE d:16 BLT d:8 BLT d:16 BGT d:8 BGT d:16 BLE d:8 BLE d:16 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 2 4 2 4 2 4 2 4 2 4 2 4 2 4 2 4 2 4 2 4 2 4 2 4 2 4 2 4 2 4 2 4 ------------ ------------ ------------ ------------ ------------ ------------ ------------ ------------ ------------ ------------ 4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6 C=1 ------------ ------------ Z=0 ------------ ------------ Z=1 ------------ ------------ V=0 ------------ ------------ V=1 ------------ ------------ N=0 ------------ ------------ N=1 ------------ ------------ NV = 0 ------------ ------------ NV = 1 Z (NV) = 0 Z (NV) = 1 ------------ ------------ ------------ ------------ ------------ ------------ Rev. 1.00, 11/03, page 336 of 376 Advanced Mnemonic Operation @(d, PC) Normal @@aa @ERn @aa #xx Rn -- Addressing Mode and Instruction Length (bytes) @-ERn/@ERn+ Operand Size Condition Code No. of States*1 @(d, ERn) @(d, PC) @@aa @aa -- I H N Z V C JMP JMP @ERn JMP @aa:24 JMP @@aa:8 -- -- -- -- 2 4 2 2 PC ERn PC aa:24 PC @aa:8 PC @-SP PC PC+d:8 PC @-SP PC PC+d:16 PC @-SP PC ERn 4 PC @-SP PC aa:24 2 PC @-SP PC @aa:8 2 PC @SP+ ------------ ------------ ------------ ------------ 8 6 4 6 10 8 BSR BSR d:8 BSR d:16 JSR -- 4 ------------ 8 10 JSR @ERn -- 2 ------------ 6 JSR @aa:24 -- ------------ 8 10 JSR @@aa:8 -- ------------ 8 12 RTS RTS -- ------------ 8 10 Rev. 1.00, 11/03, page 337 of 376 Advanced Mnemonic Operation Normal @ERn #xx Rn 8 * System control instructions Addressing Mode and Instruction Length (bytes) @-ERn/@ERn+ Operand Size Condition Code No. of States*1 @(d, ERn) @(d, PC) @@aa @aa -- I H N Z V C TRAPA TRAPA #x:2 -- 2 PC @-SP CCR @-SP 1 -- -- -- -- -- 14 16 RTE RTE -- 10 SLEEP SLEEP -- ------------ 2 LDC LDC #xx:8, CCR LDC Rs, CCR LDC @ERs, CCR LDC @(d:16, ERs), CCR LDC @(d:24, ERs), CCR LDC @ERs+, CCR B B W W W W 2 2 6 8 12 8 LDC @aa:16, CCR LDC @aa:24, CCR STC STC CCR, Rd STC CCR, @ERd STC CCR, @(d:16, ERd) STC CCR, @(d:24, ERd) STC CCR, @-ERd W W B W W W W 8 10 2 6 8 12 8 ------------ ------------ ------------ ------------ ------------ ------------ ------------ STC CCR, @aa:16 STC CCR, @aa:24 ANDC ANDC #xx:8, CCR ORC NOP ORC #xx:8, CCR XORC XORC #xx:8, CCR NOP W W B B B -- 8 10 2 2 2 2 ------------ Rev. 1.00, 11/03, page 338 of 376 Advanced Mnemonic Operation Normal @ERn #xx Rn * Block transfer instructions Addressing Mode and Instruction Length (bytes) @-ERn/@ERn+ Operand Size Condition Code No. of States*1 @(d, ERn) I H N Z V C EEPMOV EEPMOV. B -- 4 if R4L 0 then repeat @R5 @R6 R5+1 R5 R6+1 R6 R4L-1 R4L until R4L=0 else next 4 if R4 0 then repeat @R5 @R6 R5+1 R5 R6+1 R6 R4-1 R4 until R4=0 else next -- -- -- -- -- -- 8+ 4n*2 EEPMOV. W -- -- -- -- -- -- -- 8+ 4n*2 Notes: 1. The number of states in cases where the instruction code and its operands are located in on-chip memory is shown here. For other cases see Appendix A.3, Number of Execution States. 2. n is the value set in register R4L or R4. (1) Set to 1 when a carry or borrow occurs at bit 11; otherwise cleared to 0. (2) Set to 1 when a carry or borrow occurs at bit 27; otherwise cleared to 0. (3) Retains its previous value when the result is zero; otherwise cleared to 0. (4) Set to 1 when the adjustment produces a carry; otherwise retains its previous value. (5) The number of states required for execution of an instruction that transfers data in synchronization with the E clock is variable. (6) Set to 1 when the divisor is negative; otherwise cleared to 0. (7) Set to 1 when the divisor is zero; otherwise cleared to 0. (8) Set to 1 when the quotient is negative; otherwise cleared to 0. Rev. 1.00, 11/03, page 339 of 376 Advanced Mnemonic Operation @(d, PC) Normal @@aa @ERn @aa #xx Rn -- A.2 Table A.2 Instruction code: Instruction when most significant bit of BH is 1. 4 ORC ADD SUB Table A-2 Table A-2 (2) (2) CMP MOV OR.B XOR.B AND.B Table A-2 (2) XORC ANDC LDC Table A-2 Table A-2 (2) (2) ADDX SUBX 5 6 7 8 9 A B C D E F Table A-2 (2) Table A-2 (2) 1st byte 2nd byte AH AL BH BL Instruction when most significant bit of BH is 0. 3 LDC AL AH 0 1 2 0 NOP Table A-2 (2) STC 1 Table A-2 Table A-2 Table A-2 Table A-2 (2) (2) (2) (2) 2 MOV.B Rev. 1.00, 11/03, page 340 of 376 Operation Code Map Operation Code Map (1) 3 BLS BVS JMP MOV MOV BIOR ADD ADDX CMP SUBX OR XOR AND MOV BIXOR BIAND BILD Table A-2 Table A-2 EEPMOV (2) (2) Table A-2 (3) DIVXU BST OR BTST BOR BXOR BAND BIST BLD XOR AND RTS BSR RTE TRAPA Table A-2 (2) BCC BCS BNE BEQ BVC BPL BMI BGE BSR BLT BGT JSR BLE 4 BRA BRN BHI 5 MULXU DIVXU MULXU 6 BSET BNOT BCLR 7 8 9 A B C D E F Table A.2 Instruction code: 1st byte 2nd byte AH AL BH BL 2 LDC/STC SLEEP ADD INC ADDS MOV SHLL SHAL SHAR ROTL ROTR EXTU EXTU NEG SHLR ROTXL ROTXR NOT SHAL SHAR ROTL ROTR NEG SUB DEC DEC SUB CMP BHI BLS SUB SUB OR OR CMP CMP BCC BCS XOR XOR BNE AND AND BEQ BVC BVS BPL BMI BGE BLT BGT BLE DEC DEC EXTS EXTS INC INC INC 3 4 5 6 7 8 9 A B C D E F Table A-2 (3) BH AH AL 0 1 01 MOV Table A-2 Table A-2 (3) (3) 0A INC 0B ADDS Operation Code Map (2) 0F DAA 10 SHLL 11 SHLR 12 ROTXL 13 ROTXR 17 NOT 1A DEC 1B SUBS 1F DAS 58 BRA BRN 79 MOV ADD Rev. 1.00, 11/03, page 341 of 376 7A MOV ADD Table A.2 Instruction code: 1st byte 2nd byte 3rd byte 4th byte AH AL BH BL CH CL DH DL Instruction when most significant bit of DH is 0. Instruction when most significant bit of DH is 1. CL 2 3 4 5 6 7 8 9 A B C D E F AH ALBH BLCH LDC STC STC MULXS DIVXS OR BTST BOR BTST BIOR BCLR BIST BCLR BTST BOR BTST BIOR BCLR BIST BCLR BIXOR BIAND BILD BST BXOR BAND BLD BIXOR BIAND BILD BST BXOR BAND BLD XOR AND LDC 0 1 Rev. 1.00, 11/03, page 342 of 376 LDC STC LDC STC 01406 Operation Code Map (3) 01C05 MULXS 01D05 DIVXS 01F06 7Cr06 * 1 7Cr07 * 1 7Dr06 * 1 BSET BNOT 7Dr07 * 1 BSET BNOT 7Eaa6 * 2 7Eaa7 * 2 7Faa6 * 2 BSET BNOT 7Faa7 * 2 BSET BNOT Notes: 1. r is the register designation field. 2. aa is the absolute address field. A.3 Number of Execution States The status of execution for each instruction of the H8/300H CPU and the method of calculating the number of states required for instruction execution are shown below. Table A.4 shows the number of cycles of each type occurring in each instruction, such as instruction fetch and data read/write. Table A.3 shows the number of states required for each cycle. The total number of states required for execution of an instruction can be calculated by the following expression: Execution states = I x SI + J x SJ + K x SK + L x SL + M x SM + N x SN Examples: When instruction is fetched from on-chip ROM, and an on-chip RAM is accessed. BSET #0, @FF00 From table A.4: I = L = 2, J = K = M = N= 0 From table A.3: SI = 2, SL = 2 Number of states required for execution = 2 x 2 + 2 x 2 = 8 When instruction is fetched from on-chip ROM, branch address is read from on-chip ROM, and on-chip RAM is used for stack area. JSR @@ 30 From table A.4: I = 2, J = K = 1, From table A.3: SI = SJ = SK = 2 Number of states required for execution = 2 x 2 + 1 x 2+ 1 x 2 = 8 L=M=N=0 Rev. 1.00, 11/03, page 343 of 376 Table A.3 Number of Cycles in Each Instruction Access Location On-Chip Memory SI SJ SK SL SM SN 2 or 3* 2 or 3* 1 2 On-Chip Peripheral Module -- Execution Status (Instruction Cycle) Instruction fetch Branch address read Stack operation Byte data access Word data access Internal operation Note: * Depends on which on-chip peripheral module is accessed. See section 19.1, Register Addresses (Address Order). Rev. 1.00, 11/03, page 344 of 376 Table A.4 Number of Cycles in Each Instruction Instruction Fetch Branch J Stack K Byte Data Access L Word Data Access M Internal Operation N Addr. Read Operation Instruction Mnemonic ADD ADD.B #xx:8, Rd ADD.B Rs, Rd ADD.W #xx:16, Rd ADD.W Rs, Rd ADD.L #xx:32, ERd ADD.L ERs, ERd ADDS ADDX ADDS #1/2/4, ERd ADDX #xx:8, Rd ADDX Rs, Rd AND AND.B #xx:8, Rd AND.B Rs, Rd AND.W #xx:16, Rd AND.W Rs, Rd AND.L #xx:32, ERd AND.L ERs, ERd ANDC BAND ANDC #xx:8, CCR BAND #xx:3, Rd BAND #xx:3, @ERd BAND #xx:3, @aa:8 Bcc BRA d:8 (BT d:8) BRN d:8 (BF d:8) BHI d:8 BLS d:8 BCC d:8 (BHS d:8) BCS d:8 (BLO d:8) BNE d:8 BEQ d:8 BVC d:8 BVS d:8 BPL d:8 BMI d:8 BGE d:8 I 1 1 2 1 3 1 1 1 1 1 1 2 1 3 2 1 1 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 1 1 Rev. 1.00, 11/03, page 345 of 376 Instruction Fetch Instruction Mnemonic Bcc BLT d:8 BGT d:8 BLE d:8 BRA d:16(BT d:16) BRN d:16(BF d:16) BHI d:16 BLS d:16 BCC d:16(BHS d:16) BCS d:16(BLO d:16) BNE d:16 BEQ d:16 BVC d:16 BVS d:16 BPL d:16 BMI d:16 BGE d:16 BLT d:16 BGT d:16 BLE d:16 BCLR BCLR #xx:3, Rd BCLR #xx:3, @ERd BCLR #xx:3, @aa:8 BCLR Rn, Rd BCLR Rn, @ERd BCLR Rn, @aa:8 BIAND BIAND #xx:3, Rd BIAND #xx:3, @ERd BIAND #xx:3, @aa:8 BILD BILD #xx:3, Rd BILD #xx:3, @ERd BILD #xx:3, @aa:8 I 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 1 2 2 1 2 2 1 2 2 1 2 2 Branch J Stack K Byte Data Access L Word Data Access M Internal Operation N Addr. Read Operation 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 1 1 1 1 Rev. 1.00, 11/03, page 346 of 376 Instruction Fetch Instruction Mnemonic BIOR BIOR #xx:8, Rd BIOR #xx:8, @ERd BIOR #xx:8, @aa:8 BIST BIST #xx:3, Rd BIST #xx:3, @ERd BIST #xx:3, @aa:8 BIXOR BIXOR #xx:3, Rd BIXOR #xx:3, @ERd BIXOR #xx:3, @aa:8 BLD BLD #xx:3, Rd BLD #xx:3, @ERd BLD #xx:3, @aa:8 BNOT BNOT #xx:3, Rd BNOT #xx:3, @ERd BNOT #xx:3, @aa:8 BNOT Rn, Rd BNOT Rn, @ERd BNOT Rn, @aa:8 BOR BOR #xx:3, Rd BOR #xx:3, @ERd BOR #xx:3, @aa:8 BSET BSET #xx:3, Rd BSET #xx:3, @ERd BSET #xx:3, @aa:8 BSET Rn, Rd BSET Rn, @ERd BSET Rn, @aa:8 BSR BSR d:8 BSR d:16 BST BST #xx:3, Rd BST #xx:3, @ERd BST #xx:3, @aa:8 I 1 2 2 1 2 2 1 2 2 1 2 2 1 2 2 1 2 2 1 2 2 1 2 2 1 2 2 2 2 1 2 2 Branch J Stack K Byte Data Access L Word Data Access M Internal Operation N Addr. Read Operation 1 1 2 2 1 1 1 1 2 2 2 2 1 1 2 2 2 2 1 1 2 2 2 Rev. 1.00, 11/03, page 347 of 376 Instruction Fetch Instruction Mnemonic BTST BTST #xx:3, Rd BTST #xx:3, @ERd BTST #xx:3, @aa:8 BTST Rn, Rd BTST Rn, @ERd BTST Rn, @aa:8 BXOR BXOR #xx:3, Rd BXOR #xx:3, @ERd BXOR #xx:3, @aa:8 CMP CMP.B #xx:8, Rd CMP.B Rs, Rd CMP.W #xx:16, Rd CMP.W Rs, Rd CMP.L #xx:32, ERd CMP.L ERs, ERd DAA DAS DEC DAA Rd DAS Rd DEC.B Rd DEC.W #1/2, Rd DEC.L #1/2, ERd DUVXS DIVXS.B Rs, Rd DIVXS.W Rs, ERd DIVXU DIVXU.B Rs, Rd DIVXU.W Rs, ERd EEPMOV EEPMOV.B EEPMOV.W EXTS EXTS.W Rd EXTS.L ERd EXTU EXTU.W Rd EXTU.L ERd I 1 2 2 1 2 2 1 2 2 1 1 2 1 3 1 1 1 1 1 1 2 2 1 1 2 2 1 1 1 1 Branch J Stack K Byte Data Access L Word Data Access M Internal Operation N Addr. Read Operation 1 1 1 1 1 1 12 20 12 20 2n+2* 1 1 2n+2* Rev. 1.00, 11/03, page 348 of 376 Instruction Fetch Instruction Mnemonic INC INC.B Rd INC.W #1/2, Rd INC.L #1/2, ERd JMP JMP @ERn JMP @aa:24 JMP @@aa:8 JSR JSR @ERn JSR @aa:24 JSR @@aa:8 LDC LDC #xx:8, CCR LDC Rs, CCR LDC@ERs, CCR LDC@(d:16, ERs), CCR LDC@(d:24,ERs), CCR LDC@ERs+, CCR LDC@aa:16, CCR LDC@aa:24, CCR MOV MOV.B #xx:8, Rd MOV.B Rs, Rd MOV.B @ERs, Rd MOV.B @(d:16, ERs), Rd MOV.B @(d:24, ERs), Rd MOV.B @ERs+, Rd MOV.B @aa:8, Rd MOV.B @aa:16, Rd MOV.B @aa:24, Rd MOV.B Rs, @Erd MOV.B Rs, @(d:16, ERd) MOV.B Rs, @(d:24, ERd) MOV.B Rs, @-ERd MOV.B Rs, @aa:8 I 1 1 1 2 2 2 2 2 2 1 1 2 3 5 2 3 4 1 1 1 2 4 1 1 2 3 1 2 4 1 1 Branch J Stack K Byte Data Access L Word Data Access M Internal Operation N Addr. Read Operation 2 1 1 1 1 1 2 2 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 2 2 Rev. 1.00, 11/03, page 349 of 376 Instruction Fetch Instruction Mnemonic MOV MOV.B Rs, @aa:16 MOV.B Rs, @aa:24 MOV.W #xx:16, Rd MOV.W Rs, Rd MOV.W @ERs, Rd MOV.W @(d:16,ERs), Rd MOV.W @(d:24,ERs), Rd MOV.W @ERs+, Rd MOV.W @aa:16, Rd MOV.W @aa:24, Rd MOV.W Rs, @ERd MOV.W Rs, @(d:16,ERd) MOV.W Rs, @(d:24,ERd) MOV MOV.W Rs, @-ERd MOV.W Rs, @aa:16 MOV.W Rs, @aa:24 MOV.L #xx:32, ERd MOV.L ERs, ERd MOV.L @ERs, ERd MOV.L @(d:16,ERs), ERd MOV.L @(d:24,ERs), ERd MOV.L @ERs+, ERd MOV.L @aa:16, ERd MOV.L @aa:24, ERd MOV.L ERs,@ERd MOV.L ERs, @(d:16,ERd) MOV.L ERs, @(d:24,ERd) MOV.L ERs, @-ERd MOV.L ERs, @aa:16 MOV.L ERs, @aa:24 MOVFPE MOVTPE MOVFPE @aa:16, Rd* MOVTPE Rs,@aa:16* 2 Branch J Stack K Byte Data Access L 1 1 Word Data Access M Internal Operation N Addr. Read Operation I 2 3 2 1 1 2 4 1 2 3 1 2 4 1 2 3 3 1 2 3 5 2 3 4 2 3 5 2 3 4 2 2 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 2 2 1 1 2 2 2 Rev. 1.00, 11/03, page 350 of 376 Instruction Fetch Instruction Mnemonic MULXS MULXS.B Rs, Rd MULXS.W Rs, ERd MULXU MULXU.B Rs, Rd MULXU.W Rs, ERd NEG NEG.B Rd NEG.W Rd NEG.L ERd NOP NOT NOP NOT.B Rd NOT.W Rd NOT.L ERd OR OR.B #xx:8, Rd OR.B Rs, Rd OR.W #xx:16, Rd OR.W Rs, Rd OR.L #xx:32, ERd OR.L ERs, ERd ORC POP ORC #xx:8, CCR POP.W Rn POP.L ERn PUSH PUSH.W Rn PUSH.L ERn ROTL ROTL.B Rd ROTL.W Rd ROTL.L ERd ROTR ROTR.B Rd ROTR.W Rd ROTR.L ERd ROTXL ROTXL.B Rd ROTXL.W Rd ROTXL.L ERd I 2 2 1 1 1 1 1 1 1 1 1 1 1 2 1 3 2 1 1 2 1 2 1 1 1 1 1 1 1 1 1 Branch J Stack K Byte Data Access L Word Data Access M Internal Operation N 12 20 12 20 Addr. Read Operation 1 2 1 2 2 2 2 2 Rev. 1.00, 11/03, page 351 of 376 Instruction Fetch Instruction Mnemonic ROTXR ROTXR.B Rd ROTXR.W Rd ROTXR.L ERd RTE RTS SHAL RTE RTS SHAL.B Rd SHAL.W Rd SHAL.L ERd SHAR SHAR.B Rd SHAR.W Rd SHAR.L ERd SHLL SHLL.B Rd SHLL.W Rd SHLL.L ERd SHLR SHLR.B Rd SHLR.W Rd SHLR.L ERd SLEEP STC SLEEP STC CCR, Rd STC CCR, @ERd STC CCR, @(d:16,ERd) STC CCR, @(d:24,ERd) STC CCR,@-ERd STC CCR, @aa:16 STC CCR, @aa:24 SUB SUB.B Rs, Rd SUB.W #xx:16, Rd SUB.W Rs, Rd SUB.L #xx:32, ERd SUB.L ERs, ERd SUBS SUBS #1/2/4, ERd I 1 1 1 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 3 5 2 3 4 1 2 1 3 1 1 Branch J Stack K Byte Data Access L Word Data Access M Internal Operation N Addr. Read Operation 2 1 2 2 1 1 1 1 1 1 2 Rev. 1.00, 11/03, page 352 of 376 Instruction Fetch Instruction Mnemonic SUBX SUBX #xx:8, Rd SUBX. Rs, Rd TRAPA XOR TRAPA #xx:2 XOR.B #xx:8, Rd XOR.B Rs, Rd XOR.W #xx:16, Rd XOR.W Rs, Rd XOR.L #xx:32, ERd XOR.L ERs, ERd XORC XORC #xx:8, CCR I 1 1 2 1 1 2 1 3 2 1 Branch J Stack K Byte Data Access L Word Data Access M Internal Operation N Addr. Read Operation 1 2 4 Notes: 1. n: Specified value in R4L and R4. The source and destination operands are accessed n+1 times respectively. 2. Cannot be used in this LSI. Rev. 1.00, 11/03, page 353 of 376 A.4 Combinations of Instructions and Addressing Modes Combinations of Instructions and Addressing Modes Addressing Mode @ERn+/@ERn @(d:16.ERn) @(d:24.ERn) @(d:16.PC) Table A.5 @@aa:8 Functions Instructions @ERn #xx @(d:8.PC) @aa:16 @aa:24 @aa:8 Rn Data MOV transfer POP, PUSH instructions MOVFPE, MOVTPE Arithmetic operations ADD, CMP SUB ADDX, SUBX ADDS, SUBS INC, DEC DAA, DAS MULXU, MULXS, DIVXU, DIVXS NEG EXTU, EXTS BWL BWL BWL BWL BWL BWL -- -- -- -- -- -- -- -- -- -- -- -- BWL WL B -- -- -- -- BWL BWL B L BWL B BW -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- B -- -- -- -- -- -- -- -- -- BWL BWL -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- WL -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- B -- B -- -- BWL WL BWL BWL BWL B -- -- -- -- -- -- B B -- -- -- -- -- -- -- -- B -- -- -- -- -- W W -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- W W -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- W W -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- W W -- -- -- -- -- -- -- -- B -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- W W -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Logical operations AND, OR, XOR NOT Shift operations Bit manipulations Branching BCC, BSR instructions JMP, JSR RTS System TRAPA control RTE instructions SLEEP LDC STC ANDC, ORC, XORC NOP Block data transfer instructions -- -- -- W W -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- BW Rev. 1.00, 11/03, page 354 of 376 -- Appendix B I/O Port Block Diagrams B.1 I/O Port Block Diagrams RES goes low in a reset, and SBY goes low in a reset and in standby mode. Internal data bus PUCR Pull-up MOS PMR PDR PCR TRGV [Legend] PUCR: Port pull-up control register PMR: Port mode register PDR: Port data register PCR: Port control register Figure B.1 Port 1 Block Diagram (P17) Rev. 1.00, 11/03, page 355 of 376 Internal data bus PUCR Pull-up MOS PMR PDR PCR [Legend] PUCR: Port pull-up control register PMR: Port mode register PDR: Port data register PCR: Port control register Figure B.2 Port 1 Block Diagram (P14) Rev. 1.00, 11/03, page 356 of 376 Internal data bus PMR PDR PCR SCI3 TXD [Legend] PMR: Port mode register PDR: Port data register PCR: Port control register Figure B.3 Port 2 Block Diagram (P22) Rev. 1.00, 11/03, page 357 of 376 Internal data bus PDR PCR SCI3 RE RXD [Legend] PDR: Port data register PCR: Port control register Figure B.4 Port 2 Block Diagram (P21) Rev. 1.00, 11/03, page 358 of 376 SCI3 SCKIE SCKOE Internal data bus PDR PCR SCKO SCKI [Legend] PDR: Port data register PCR: Port control register Figure B.5 Port 2 Block Diagram (P20) Rev. 1.00, 11/03, page 359 of 376 Internal data bus PDR PCR IIC2 ICE SDAO/SCLO SDAI/SCLI [Legend] PDR: Portdata register PCR: Portcontrol register Figure B.6 (1) Port 5 Block Diagram (P57, P56) (for H8/36912 Group) Internal data bus PDR PCR [Legend] PDR: PCR: Portdata register Portcontrol register Figure B.6 (2) Port 5 Block Diagram (P57, P56) (for H8/36902 Group) Rev. 1.00, 11/03, page 360 of 376 Internal data bus PUCR Pull-up MOS PMR PDR PCR [Legend] PUCR: Port pull-up control register PMR: Port mode register PDR: Port data register PCR: Port control register Figure B.7 Port 5 Block Diagram (P55) Rev. 1.00, 11/03, page 361 of 376 Internal data bus Timer V OS3 OS2 OS1 OS0 PDR PCR TMOV [Legend] PDR: Portdata register PCR: Portcontrol register Figure B.8 Port 5 Block Diagram (P76) Internal data bus PDR PCR Timer V TMCIV [Legend] PDR: Portdata register PCR: Portcontrol register Figure B.9 Port 7 Block Diagram (P75) Rev. 1.00, 11/03, page 362 of 376 Internal data bus PDR PCR Timer V TMRIV [Legend] PDR: Portdata register PCR: Portcontrol register Figure B.10 Port 7 Block Diagram (P74) Rev. 1.00, 11/03, page 363 of 376 Internal data bus Timer W Output control signal A to D PDR PCR FTIOA to D [Legend] PDR: Portdata register PCR: Portcontrol register Figure B.11 Port 8 Block Diagram (P84 to P81) Rev. 1.00, 11/03, page 364 of 376 Internal data bus PDR PCR Timer W FTCI [Legend] PDR: Portdata register PCR: Portcontrol register Figure B.12 Port 8 Block Diagram (P80) Rev. 1.00, 11/03, page 365 of 376 Internal data bus A/D converter CH3 to CH0 SCAN VIN DEC Low voltage detection circuit VDDII ExtD, ExtU [Legend] PDR: Portdata register PCR: Portcontrol register Figure B.13 Port B Block Diagram (PB3,PB2) Internal data bus A/D converter SCAN CH3 to CH0 VIN DEC Figure B.14 Port B Block Diagram (PB1, PB0) Rev. 1.00, 11/03, page 366 of 376 Internal data bus CPG PDR PCR PMRC1 PMRC0 XTALI [Legend] PDR: Portdata register PCR: Portcontrol register Figure B.15 Port C Block Diagram (PC1) Rev. 1.00, 11/03, page 367 of 376 Internal data bus PDR PCR CPG PMRC0 EXTALI [Legend] PDR: Portdata register PCR: Portcontrol register Figure B.16 Port C Block Diagram (PC0) Rev. 1.00, 11/03, page 368 of 376 B.2 Port P17, P14 Port States in Each Operating State Reset High impedance High impedance High impedance High impedance High impedance High impedance High impedance Active Functioning Functioning Functioning Functioning Functioning High impedance Functioning Sleep Retained Retained Retained Retained Retained High impedance Retained Subsleep Retained Retained Retained Retained Retained Retained Retained Standby High impedance* High impedance High impedance* High impedance High impedance High impedance High impedance P22 to P20 P57 to P55 P76 to P74 P84 to P80 PB3 to PB0 PC1, PC0 Note: * High level output when the pull-up MOS is in on state. Rev. 1.00, 11/03, page 369 of 376 Appendix C Product Code Lineup Product Type H8/36912 Flash memory version Masked ROM version H8/36911 Masked ROM version H8/36902 Flash memory version Masked ROM version H8/36901 Masked ROM version H8/36900 Masked ROM version [Legend] (***): ROM code Product Code HD64F36912G Model Marking HD64F36912G FH HD64F36912G TP HD64336912G HD64336912G (***) FH HD64336912G (***) TP HD64336911G HD64336911G (***) FH HD64336911G (***) TP HD64F36902G HD64336902G HD64336901G HD64336900G HD64F36902G FH HD64F36902G TP HD64336902G (***) FH HD64336902G (***) TP HD64336901G (***) FH HD64336901G (***) TP HD64336900G (***) FH HD64336900G (***) TP Package Code LQFP-32 (FP-32) SOP-32 (FP-32D) LQFP-32 (FP-32) SOP-32 (FP-32D) LQFP-32 (FP-32) SOP-32 (FP-32D) LQFP-32 (FP-32) SOP-32 (FP-32D) LQFP-32 (FP-32) SOP-32 (FP-32D) LQFP-32 (FP-32) SOP-32 (FP-32D) LQFP-32 (FP-32) SOP-32 (FP-32D) Rev. 1.00, 11/03, page 370 of 376 Appendix D Package Dimensions The package dimensions that are shows in the Renesas Semiconductor Packages Data Book have priority. Unit: mm 20.45 20.95 Max 32 17 1 1.00 Max 16 11.30 3.00 Max *0.22 0.05 0.20 0.04 14.14 0.30 1.42 1.27 *0.40 0.08 0.10 0.15 M 0.12 0.15 + 0.10 - 0 - 8 0.80 0.20 0.38 0.06 *Dimension including the plating thickness Base material dimension Package Code JEDEC JEITA Mass (reference value) FP-32D Conforms -- 1.3 g Figure D.1 FP-32D Package Dimensions TBD Figure D.2 LQFP-32 Package Dimension Rev. 1.00, 11/03, page 371 of 376 Rev. 1.00, 11/03, page 372 of 376 Index A/D converter ......................................... 255 A/D conversion time ........................... 262 External trigger input .......................... 263 Sample-and-hold circuit...................... 262 Scan mode........................................... 261 Single mode ........................................ 261 Acknowledge .......................................... 238 Address break ........................................... 59 Addressing modes Absolute address ................................... 32 Immediate ............................................. 33 Memory indirect ................................... 33 Program-counter relative ...................... 33 Register direct ....................................... 31 Register indirect.................................... 31 Register indirect with displacement...... 32 Register indirect with post-increment ... 32 Register indirect with pre-decrement .... 32 Bit Synchronous Circuit.......................... 254 Clock pulse generators System Prescaler S................................ 81 Clock Synchronous Serial Format .......... 246 Condition field .......................................... 30 Condition-code register (CCR) ................. 16 CPU .......................................................... 11 Effective address....................................... 34 Effective address extension....................... 30 Exception handling ................................... 45 Reset exception handling ...................... 52 Stack status ........................................... 55 Trap instruction..................................... 45 Flash memory ........................................... 93 Boot mode............................................. 99 Boot program ........................................ 99 Erase/erase-verify ............................... 105 Erasing units ......................................... 94 Error protection................................... 108 Hardware protection ........................... 108 Program/program-verify ..................... 103 Programming units................................ 94 Programming/erasing in user program mode....................................................102 Software protection .............................108 General registers .......................................15 I/O ports ..................................................111 I/O port block diagrams.......................355 2 I C Bus Format........................................238 I2C Bus Interface 2 (IIC2) .......................225 Instruction set............................................21 Arithmetic operations instructions ........23 Bit Manipulation instructions................26 Block data transfer instructions.............29 Branch instructions................................28 Data Transfer instructions .....................22 Logic Operations instructions ...............24 Shift Instructions ...................................25 System control instructions ...................29 Internal power supply step-down circuit ......................................................279 Interrupt Internal interrupts ..................................54 Interrupt response time..........................56 IRQ3 to IRQ0 interrupts........................53 NMI interrupt ........................................53 WKP5 to WKP0 interrupts....................53 Low-voltage detection circuit..................267 LVDI ...............................................274, 275 LVDI (interrupt by low voltage detect) circuit ..............................................274, 275 LVDR......................................................273 LVDR (reset by low voltage detect) circuit ................................................................273 Memory map .............................................12 Module standby function...........................92 Noise Canceler ........................................248 On-board programming modes .................99 Operation field ..........................................30 Package .......................................................2 Package dimensions ................................371 Power-down modes...................................83 Rev. 1.00, 11/03, page 373 of 376 Sleep mode ........................................... 90 Standby mode ....................................... 91 Subsleep mode ...................................... 91 Power-on reset ........................................ 267 Power-on reset circuit ............................. 272 Product code lineup ................................ 370 Program counter (PC) ............................... 16 PWM operation....................................... 168 Register ABRKCR...................... 60, 283, 287, 289 ABRKSR ...................... 61, 283, 287, 289 ADCR ......................... 259, 283, 286, 289 ADCSR....................... 258, 283, 286, 289 ADDRA ...................... 257, 283, 286, 289 ADDRB ...................... 257, 283, 286, 289 ADDRC ...................... 257, 283, 286, 289 ADDRD ...................... 257, 283, 286, 289 BARH ........................... 62, 283, 287, 289 BARL............................ 62, 284, 287, 289 BDRH ........................... 62, 284, 287, 289 BDRL............................ 62, 284, 287, 289 BRR ............................ 196, 283, 286, 289 EBR1 ............................ 98, 283, 286, 288 FENR ............................ 98, 283, 286, 288 FLMCR1....................... 96, 283, 286, 288 FLMCR2....................... 97, 283, 286, 288 GRA............................ 163, 283, 285, 288 GRB ............................ 163, 283, 285, 288 GRC ............................ 163, 283, 286, 288 GRD............................ 163, 283, 286, 288 ICCR1......................... 228, 282, 285, 288 ICCR2......................... 229, 282, 285, 288 ICDRR ........................ 237, 282, 285, 288 ICDRS ................................................ 237 ICDRT ........................ 237, 282, 285, 288 ICIER.......................... 232, 282, 285, 288 ICMR .......................... 231, 282, 285, 288 ICSR ........................... 234, 282, 285, 288 IEGR1........................... 47, 284, 287, 290 IEGR2........................... 48, 284, 287, 290 IENR1........................... 48, 284, 287, 290 IRR1.............................. 50, 284, 287, 290 IWPR ............................ 51, 284, 287, 290 Rev. 1.00, 11/03, page 374 of 376 LVDCR ....................... 269, 282, 285, 288 LVDSR ....................... 271, 282, 285, 288 MSTCR1 ....................... 87, 284, 287, 290 MSTCR2 ....................... 88, 284, 287, 290 PCR1 ........................... 113, 284, 287, 290 PCR2 ........................... 115, 284, 287, 290 PCR5 ........................... 118, 284, 287, 290 PCR7 ........................... 121, 284, 287, 290 PCR8 ........................... 124, 284, 287, 290 PDR1........................... 113, 284, 287, 289 PDR2........................... 116, 284, 287, 289 PDR5........................... 119, 284, 287, 289 PDR7........................... 122, 284, 287, 289 PDR8........................... 124, 284, 287, 289 PDRB .......................... 127, 284, 287, 289 PMR1 .......................... 112, 284, 287, 290 PMR5 .......................... 118, 284, 287, 290 PUCR1 ........................ 114, 284, 287, 289 PUCR5 ........................ 119, 284, 287, 289 RDR ............................ 190, 283, 286, 289 RSR..................................................... 190 SAR............................. 236, 282, 285, 288 SCR3 ........................... 192, 283, 286, 289 SMR ............................ 191, 283, 286, 289 SPMR.......................... 201, 283, 286, 289 SSR ............................. 194, 283, 286, 289 SYSCR1........................ 84, 284, 287, 290 SYSCR2........................ 86, 284, 287, 290 TCB1........................... 135, 282, 285, 288 TCNT .................................. 163, 285, 288 TCNTV ....................... 139, 283, 286, 289 TCORA ....................... 139, 283, 286, 289 TCORB ....................... 139, 283, 286, 289 TCRV0........................ 140, 283, 286, 289 TCRV1........................ 143, 283, 286, 289 TCRW ......................... 156, 282, 285, 288 TCSRV........................ 142, 283, 286, 289 TCSRWD.................... 182, 283, 286, 289 TCWD......................... 184, 283, 286, 289 TDR ............................ 190, 283, 286, 289 TIERW........................ 157, 282, 285, 288 TIOR0 ......................... 160, 282, 285, 288 TIOR1 ......................... 161, 282, 285, 288 TLB1................................................... 135 TMB1.......................... 134, 282, 285, 288 TMRW........................ 155, 282, 285, 288 TMWD........................ 184, 283, 286, 289 TSR..................................................... 190 TSRW ......................... 158, 282, 285, 288 Register field............................................. 30 Serial communication interface 3 (SCI3) ..................................................... 187 Asynchronous mode ........................... 202 Bit rate ................................................ 196 Break................................................... 223 Clocked synchronous mode ................ 208 Framing error ...................................... 206 Multiprocessor communication function ............................................................ 215 Overrun error.......................................206 Parity error ..........................................206 Slave address...........................................238 Stack pointer (SP) .....................................15 Start condition .........................................238 Stop condition .........................................238 System clocks............................................65 Timer B1 .................................................133 Auto-reload timer operation ................136 Interval timer operation.......................136 Timer V...................................................137 Timer W ..................................................151 Transfer Rate...........................................229 Vector address...........................................45 Watchdog timer.......................................181 Rev. 1.00, 11/03, page 375 of 376 Rev. 1.00, 11/03, page 376 of 376 H8/36912 Group, H8/36902 Group Hardware Manual Publication Date: Rev.1.00, November 7, 2003 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Technical Documentation & Information Department Renesas Kodaira Semiconductor Co., Ltd. 2003 Renesas Technology Corp. All rights reserved. Printed in Japan. Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan RENESAS SALES OFFICES Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500 Fax: <1> (408) 382-7501 Renesas Technology Europe Limited. Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, United Kingdom Tel: <44> (1628) 585 100, Fax: <44> (1628) 585 900 Renesas Technology Europe GmbH Dornacher Str. 3, D-85622 Feldkirchen, Germany Tel: <49> (89) 380 70 0, Fax: <49> (89) 929 30 11 Renesas Technology Hong Kong Ltd. 7/F., North Tower, World Finance Centre, Harbour City, Canton Road, Hong Kong Tel: <852> 2265-6688, Fax: <852> 2375-6836 Renesas Technology Taiwan Co., Ltd. FL 10, #99, Fu-Hsing N. Rd., Taipei, Taiwan Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999 Renesas Technology (Shanghai) Co., Ltd. 26/F., Ruijin Building, No.205 Maoming Road (S), Shanghai 200020, China Tel: <86> (21) 6472-1001, Fax: <86> (21) 6415-2952 Renesas Technology Singapore Pte. Ltd. 1, Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632 Tel: <65> 6213-0200, Fax: <65> 6278-8001 http://www.renesas.com Colophon 1.0 H8/36912 Group, H8/36902 Group Hardware Manual REJ09B0105-0100Z |
Price & Availability of H836900 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |