View SY88993AV11_969835.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Micrel, Inc.
5V/3.3V 3.2Gbps HIGH-SPEED LIMITING POST AMPLIFIER
SY88993AV
SY88993AV
FEATURES
s s s s s s s s s > 3.2Gbps operation Low noise CML data outputs Chatter-Free LOS generation Open Collector TTL LOS output TTL /EN Input Differential PECL inputs for data Single 3.3V or 5V power supply Designed for use with SY88922V and SY88905 Available in a tiny 10-pin (3mm) MSOP
DESCRIPTION
The SY88993AV limiting post amplifier with its high and wide bandwidth is ideal for use as a post amplifier in fiberoptic receivers with data rates up to 3.2Gbps. Signals as small as 4mVp-p can be amplified to drive devices with CML inputs or AC coupled PECL inputs. The SY88993AV generates a chatter-free Loss of Signal (LOS) open collector TTL output. The SY88993AV incorporates a programmble level detect function to identify when the input signal has been lost. This information can be fed back to the /EN input of the device to maintain stability under loss of signal conditions. Using LOSLVL pin the sensitivity of the level detect can be adjusted. The LOSLVL voltage can be set by connecting a resistor divider between VCC and VREF, Figure 3.
VCC SY88993AV LOS 4.7k to 10k
APPLICATIONS
s 1.25Gbps and 2.1Gbps Gigabit Ethernet s 531Mbps, 1062Mbps and 2.5Gbps SONET/SDH Fibre Channel s 622Mbps s Gigabit interface converter (GBIC) s Small form factor trancievers s Parallel 10G Ethernet
BLOCK DIAGRAM
DIN /DIN VREF VCC GND
Limiting Amplifer
CML Buffer
DOUT /DOUT
Enable
/EN
Level Detect
LOSLVL
LOS
M9999-091207 hbwhelp@micrel.com or (408) 955-1690
Rev.: D
Amendment: /0
1
Issue Date: September 2007
Micrel, Inc.
SY88993AV
PACKAGE/ORDERING INFORMATION
Ordering Information
/EN 1 DIN 2 /DIN 3 VREF 4 LOSLVL 5 MSOP K10-1 10 VCC 9 DOUT 8 /DOUT 7 LOS 6 GND
Part Number SY88993AVKI SY88993AVKITR(1) SY88993AVKG SY88993AVKGTR(1)
Note: 1. Tape and Reel.
Package Type K10-1 K10-1 K10-1 K10-1
Operating Range Industrial Industrial Industrial Industrial
Package Marking 993A 993A 993A with Pb-Free bar-line indicator 993A with Pb-Free bar-line indicator
Lead Finish Sn-Pb Sn-Pb Pb-Free NiPdAu Pb-Free NiPdAu
10-Pin MSOP (K10-1)
PIN NAMES
Pin DIN /DIN LOSLVL /EN LOS GND DOUT /DOUT VCC VREF Type Data Input Data Input Input TTL Input TTL Output (Open Collector) Ground CML Output CML Output Power Supply Output Function Data Input Inverting Data Input Loss of Signal Level Set Output Enable (Active Low) Loss of Signal Indicator (Active High) Ground Data Output Inverting Data Output Positive Power Supply Reference Voltage Output for LOS Level Set (see Fig. 3)
GENERAL DESCRIPTION
General The SY88993AV is an integrated limiting amplifier intended for high-frequency fiber-optic applications. The circuit connects to typical transimpedance amplifiers found within a fiber-optics link. The linear signal output from a transimpedance amplifier can contain significant amounts of noise, and may vary in amplitude over time. The SY88993AV limiting amplifier quantizes the signal and outputs a voltage-limited waveform. The /EN pin allows the user to disable the output signal without removing the input signal.
ABSOLUTE MAXIMUM RATINGS(1)
Symbol VCC DIN, /DIN TA TSTORE Input Voltage Operating Temperature Range Storage Temperature Range Rating Power Supply Voltage Value 0 to +7.0 0 to VCC -40 to +85 -55 to +85 Unit V V C C
Note: 1. Permanent device damage may occur if absolute maximum ratings are exceeded. This is a stress rating only and functional operation is not implied at conditions other than those detailed in the operational sections of this data sheet. Exposure to absolute maximum ratlng conditions for extended periods may affect device reliability.
M9999-091207 hbwhelp@micrel.com or (408) 955-1690
2
Micrel, Inc.
SY88993AV
DC ELECTRICAL CHARACTERISTICS
VCC = +3.3V 10% or +5V 10%, RLOAD = 50 to VCC
TA = -40C Symbol ICC IIL IIH IOH LOSLVL VOL VREF VIH VIL Parameter Power Supply Current(1) /EN Input LOW Current /EN Input HIGH Current LOS Output Leakage(2) LOSLVL Level LOS Output Low Level(3) Reference Voltage /EN Input HIGH Voltage /EN Input LOW Voltage 5V 3.3V Min. -- -- -0.3(4) -- -- -- VREF -- Max. 55 50 -- 20(5) 100(6) 100 VCC 0.5 TA = 0C Min. -- -- -0.3(4) -- -- -- VREF -- Max. 55 50 -- 20(5) 100(6) 100 VCC 0.5 Min. -- -- -0.3(4) -- -- -- VREF -- TA = +25C Typ. 43 40 -- -- -- -- -- -- Max. 55 50 -- 20(5) 100(6) 100 VCC 0.5 TA = +85C Min. -- -- -0.3(4) -- -- -- VREF -- Max. 65 60 -- 20(5) 100(6) 100 VCC 0.5 Unit mA mA A uA V V V V V mV V
VCC -1.38 VCC -1.26 VCC -1.38 VCC -1.26 VCC -1.38 VCC -1.32 VCC -1.26 VCC -1.38 VCC -1.26 2.0 -- -- -- -- 80 2.0 0.8 -- -- -- 80 VCC-0.2 2.0 0.8 -- GND2 -- -- 9 -- -- -- 80 VCC-0.2 2.0 0.8 -- -- -- 80
VOFFSET Differential Output Offset VCMR Common Mode Range
GND2 VCC-0.2 GND2
GND2 VCC-0.2
Notes: 1. No output load. 2. VOH = 5.5V. 3. IOL = +2mA. 4. VIN = 0.5V. 5. VIN = 2.7V. 6. VIN =VCC.
M9999-091207 hbwhelp@micrel.com or (408) 955-1690
3
Micrel, Inc.
SY88993AV
AC ELECTRICAL CHARACTERISTICS
VCC = +3.3V 10% or +5V 10%, RLOAD = 50 to VCC
TA = -40C Symbol HYS PSRR tOFFL tOFFH tONL tr tf VID VOD VSR VOH VOL ZO Parameter LOS Hysteresis Power Rejection Ratio Supply(1) Min. 2 -- -- -- -- -- 4 600 4 Max. 8 -- 0.5 0.5 0.5 120 1800 -- 50 2 -- -- -- -- -- 4 600 4 TA = 0C Min. Max. 8 -- 0.5 0.5 0.5 120 1800 -- 50 Min. 2 -- -- -- -- -- 4 600 4 TA = +25C Typ. 4.6 35 0.1 0.1 0.2 60 -- 800(5) -- Max. 8 -- 0.5 0.5 0.5 120 1800 1200 50 TA = +85C Min. 2 -- -- -- -- -- 4 600 4 Max. 8 -- 0.5 0.5 0.5 120 1800 -- 50 Unit dB dB s s s ps mVPP mVPP mVPP mV mV
LOS Release Time(2) Minimum Input LOS Release Time(2) Maximum Input LOS Assert Time(2) Differential Output(3) Rise/Fall Time (20%-80%) Input Voltage Range Differential Output Voltage Swing(4) LOS Sensitivity Range
Output Spec (DOUT and /DOUT) Output HIGH Voltage Output LOW Voltage(6) Single-Ended Output(7) Impedance VCC -20 -- 40 VCC VCC -300 60 VCC -20 -- 40 VCC VCC -300 60 VCC -20 -- 40 VCC -5 50 VCC 60 VCC -20 -- 40 VCC VCC -300 60 VCC -400 VCC -300
Input Spec (DIN and /DIN) AV(Diff) B-3dB S21 Differential Voltage Gain 3dB Bandwidth Single-Ended Small Signal-Gain -- -- 26 -- -- -- -- -- 26 -- -- -- -- -- 26 39 2.5 33 -- -- -- -- -- 26 -- -- -- dB GHz dB
Notes: 1. Input referred noise = RMS output noise/low frequency gain. Input referred, 55MHz. 2. Input is a 200MHz square wave, tr < 300ps, 1.8VPP. 3. With input signal VID > 50mVPP with 50 load. 4. Input is a 200MHz square wave, tr < 300ps, 50 load. 5. VID > 10mVPP. 6. Output levels are based on 50 impedance. If the load impedance is different, the output level will be changed. 7. See output structure.
M9999-091207 hbwhelp@micrel.com or (408) 955-1690
4
Micrel, Inc.
SY88993AV
APPLICATION NOTE
Output Termination The SY88993AV outputs must be terminated with a 50 load to VCC. Layout and PCB Design Since the SY88993AV is a high-frequency component, performance can largely be determined by board layout and design. A common problem with high-gain amplifiers is feedback from the large swing outputs to the input via power supply. The SY88993AV ground pin should be connected to the circuit board ground. Use multiple PCB vias close to the part to connect to ground. Avoid long, inductive runs which can degrade performance.
ESD STRUCTURE VCC
VCC
VCC
50
50 DOUT /DOUT
50 Z0 = 50
50
Z0 = 50
16mA
GND
ESD STRUCTURE
Figure 2. Differential Output Configuration
22nF DIN
22nF
/DIN
VCC
50
50
R1 LOSLVL
VREF
R2
GND
0.1F
VREF
Figure 1. Differential Input Configuration NOTES: 1. Resistor Divider = R2/ (R1 + R2) 2. R1 + R2 5k Figure 3. LOSLVL Circuit
M9999-091207 hbwhelp@micrel.com or (408) 955-1690
5
Micrel, Inc.
SY88993AV
PERFORMANCE CURVE
LOS Assert and Deassert Levels vs LOSLVL
100 90
INPUT LEVEL (mVp-p) INPUT LEVEL (mVp-p)
LOS Assert and Deassert Levels vs LOSLVL
100 90 80 70 60 50 40 30 20 10 0 0 -0.2 -0.4 -0.6 -0.8 -1.0 -1.2 LOSLVL = VCC - V (V) 5.0V TA = 25C 2.5Gbps Pattern 223-1
80 70 60 50 40 30 20 10 0 0
3.3V TA = 25C 2.5Gbps Pattern 223-1
-0.2 -0.4 -0.6 -0.8 -1.0 -1.2 LOSLVL = VCC - V (V)
Figure 4.
Figure 5.
LOS Assert and Deassert Levels vs LOSLVL
100
INPUT LEVEL (mVp-p) INPUT LEVEL (mVp-p)
LOS Assert and Deassert Levels vs LOSLVL
100 90 80 70 60 50 40 30 20 10 0 0 -0.2 -0.4 -0.6 -0.8 -1.0 -1.2 LOSLVL = VCC - V (V) 5.0V TA = 25C 2.5Gbps Pattern 27-1
90 80 70 60 50 40 30 20 10 0
3.3V TA = 25C 2.5Gbps Pattern 27-1
0
-0.2 -0.4 -0.6 -0.8 -1.0 -1.2 LOSLVL = VCC - V (V)
Figure 6.
Figure 7.
M9999-091207 hbwhelp@micrel.com or (408) 955-1690
6
SY88993AV
VCC VCC VCC
Laserdiode
Photodiode
VCC
0.01F
TX_DATA+ TX_DATA- /DIN
DIN
OUT
Laser Module /OUT
RSER
SY88922
/EN GND
VREF RSET
200
0.01F
200
20k
APPLICATION EXAMPLE FOR 3-CHIP SET SOLUTION
GBIC Terminal
0.1F VCC IBIAS TX_FAULT TX_DISABLE LOSOUT LOSIN RX_LOS TX_OUT TX_FAULT TX_DISABLE VREF
MD
VCC 2M
1000pF
68
68
SY88904
IPIN SET 20k ILIMIT SET 20k IBIAS SET 20k IBIAS FB
RWIN VCCDET
0.1F
GND
0.1F VCC
0.1F
0.01F
LOS
RX_DATA+ RX_DATA- DOUT /DOUT
/EN
DIN
SY88993AV
0.01F
LOSLVL VREF
/DIN
22nF
GND
VCC 0.1F
20K 0.1F
M9999-091207 hbwhelp@micrel.com or (408) 955-1690
22nF From Transimpedance Amp.
Micrel, Inc.
50
50
7
Micrel, Inc.
SY88993AV
10 LEAD MSOP (K10-1)
Rev. 00
MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131
TEL
USA
+ 1 (408) 944-0800
FAX
+ 1 (408) 474-1000
WEB
http://www.micrel.com
The information furnished by Micrel in this datasheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser's use or sale of Micrel Products for use in life support appliances, devices or systems is at Purchaser's own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. (c) 2005 Micrel, Incorporated. M9999-091207 hbwhelp@micrel.com or (408) 955-1690
8

▲Up To Search▲

Price & Availability of SY88993AV11

	To Download SY88993AV11 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .