 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| 75 ?2010 littelfuse, inc revised: july 29, 2010 12:24 pm teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. teccor ? brand thyristors lxx08xx & qxx08xx & qxx08xhx series 8 amp sensitive, standard & alternistor (high commutation) triacs 8.0a triacs lxx08xx & qxx08xx & qxx08xhx series main features description 8 amp bi-directional solid state switch series is designed for ac switching and phase control applications such as motor speed and temperature modulation controls, lighting controls, and static switching relays. sensitive type devices guarantee gate control in quadrants i & iv needed for digital control circuitry. standard type devices normally operate in quadrants i & iii triggered from ac line. alternistor type devices only operate in quadrants i, ii, & iii and are used in circuits requiring high dv/dt capability. symbol value unit i t(rms) 8a v drm /v rrm 400 to 1000 v i gt (q1) 5 to 50 ma features & bene?ts t 3 p ) 4 d p n q m j b o u t ( m b t t o q b t t j w b u f e junctions t 7 p m u b h f d b q b c j m j u z v q to 1000 v t 4 v s h f d b q b c j m j u z v q to 100 a t & m f d u s j d b m m z j t p m b u f e l-package is ul recognized for 2500vrms t 4 p m j e t u b u f t x j u d i j o h eliminates arcing or contact bounce that create voltage transients t / p d p o u b d u t u p x f b s p v u from reaction of switching events t 3 f t u s j d u f e p s m j n j u f e 3 ' * generation, depending on activation point of sine wave t 3 f r v j s f t p o m z b t n b m m h b u f activation pulse in each half-cycle applications & y d f m m f o u g p s " $ t x j u d i j o h b o e q i b t f d p o u s p m b q q m j d b u j p o t such as heating, lighting, and motor speed controls. typical applications are ac solid-state switches, light dimmers, power tools, home/brown goods and white goods appliances. alternistor triacs (no snubber required) are used in b q q m j d b u j p o t x j u i f y u s f n f m z j o e v d u j w f m p b e t s f r v j s j o h highest commutation performance. internally constructed isolated packages are offered for ease of heat sinking with highest isolation voltage. schematic symbol mt2 mt1 g agency approval agency agency file number ? - 1 b d l b h f & ? 76 revised: july 29, 2010 12:24 pm ?2010 littelfuse, inc teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. 8 amp sensitive, standard & alternistor (high commutation) triacs lxx08xx & qxx08xx & qxx08xhx series absolute maximum ratings sensitive triac (4 quadrants) symbol parameter value unit i t(rms) rms on-state current (full sine wave) - y y - z t c = 80c 8a - y y 3 z - y y 7 z - y y % z t c = 85c i tsm / p o s f q f u j u j w f t v s h f q f b l p o t u b u f d v s s f o u (full cycle, t j initial = 25c) g ) [ t = 20 ms a g ) [ u n t 85 i 2 ti 2 t value for fusing t p n t a 2 s di/dt critical rate of rise of on-state current i g = 50ma with 0.1s rise time g ) [ t j = 110c a/s i gtm peak gate trigger current t p c 10 s t j = 110c a p g(av) average gate power dissipation t j = 110c 0.4 w t stg storage temperature range -40 to 150 c t j operating junction temperature range -40 to 110 c / p u f y y w p m u b h f z t f o t j u j w j u z absolute maximum ratings standard triac symbol parameter value unit i t(rms) rms on-state current (full sine wave) 2 y y 3 z 2 y y / z t c ? $ 8a 2 y y - z t c ? $ i tsm / p o s f q f u j u j w f t v s h f q f b l p o t u b u f d v s s f o u (full cycle, t j initial = 25c) g ) [ t = 20 ms a g ) [ u n t 100 i 2 ti 2 t value for fusing t p n t 41 a 2 s di/dt critical rate of rise of on-state current i g = 200ma with c 0.1s rise time g ) [ t j = 125c a/s i gtm peak gate trigger current t p c 10 s; i gt c t gtm t j = 125c 1. 8 a p g(av) average gate power dissipation t j = 125c 0.5 w t stg storage temperature range -40 to 150 c t j operating junction temperature range -40 to 125 c / p u f y y w p m u b h f z t f o t j u j w j u z 77 ?2010 littelfuse, inc revised: july 29, 2010 12:24 pm teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. teccor ? brand thyristors lxx08xx & qxx08xx & qxx08xhx series 8 amp sensitive, standard & alternistor (high commutation) triacs 8.0a triacs absolute maximum ratings alternistor (3 quadrants) symbol parameter value unit i t(rms) rms on-state current (full sine wave) 2 y y - ) z t c ? $ 8a 2 y y 3 ) z 2 y y / ) z 2 y y 7 ) z 2 y y % ) z t c ? $ i tsm / p o s f q f u j u j w f t v s h f q f b l p o t u b u f d v s s f o u (full cycle, t j initial = 25c) g ) [ t = 20 ms 2 y y 7 ) z 2 y y % ) z 80 a 2 y y - ) z 2 y y 3 ) z 2 y y / ) z g ) [ u n t 2 y y 7 ) z 2 y y % ) z 85 2 y y - ) z 2 y y 3 ) z 2 y y / ) z 100 i 2 ti 2 t value for fusing t p n t 2 y y 7 ) z 2 y y % ) z a 2 s 2 y y - ) z 2 y y 3 ) z 2 y y / ) z 41 di/dt critical rate of rise of on-state current g ) [ t j = 125c a/s i gtm peak gate trigger current t p c 10 s; i gt c i gtm t j = 125c 2 y y 7 ) z 2 y y % ) z a 2 y y - ) z 2 y y 3 ) z 2 y y / ) z 2.0 p g(av) average gate power dissipation t j = 125c i gt = 10ma 2 y y 7 ) z 2 y y % ) z 0.4 w i gt n " 2 y y - ) z 2 y y 3 ) z 2 y y / ) z 0.5 t stg storage temperature range -40 to 150 c t j operating junction temperature range -40 to 125 c / p u f y y w p m u b h f z t f o t j u j w j u z electrical characteristics (t j = 25c, unless otherwise speci?ed) sensitive triac (4 quadrants) symbol test conditions quadrant lxx08x6 lxx08x8 unit i gt v d = 12v r l 8 * o * * o * * * iv max. 5 10 10 20 ma v gt all max. v v gd v d = v drm r l l 8 t j = 110c all . * / 0.2 v i ) i t = 100ma max. 10 20 ma dv/dt v d = v drm gate open t j = 100c 400v typ. 40 v/s 7 20 (dv/dt)c e j e u d " n t 5 j = 110c typ. 2 2 v/s t gt i g = 100ma pw = 15s i t " q l typ. s / p u f y y w p m u b h f y q b d l b h f z t f o t j u j w j u z 78 revised: july 29, 2010 12:24 pm ?2010 littelfuse, inc teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. 8 amp sensitive, standard & alternistor (high commutation) triacs lxx08xx & qxx08xx & qxx08xhx series electrical characteristics (t j = 25c, unless otherwise speci?ed) standard triac symbol test conditions quadrant qxx08x4 qxx08x5 unit i gt v d = 12v r l 8 * o * * o * * * iv max. typ. 25 50 50 ma v gt * o * * o * * * max. v v gd v d = v drm r l l 8 t j = 125c all . * / 0.2 v i ) i t = 200ma max. 50 50 ma dv/dt v d = v drm gate open t j = 125c 400v . * / 150 v/s 7 125 800v 100 1000v 80 (dv/dt)c e j e u d " n t 5 j = 125c typ. 4 4 v/s t gt i g = 100ma pw = 15s i t " q l typ. s electrical characteristics (t j = 25c, unless otherwise speci?ed) alternistor triac (3 quadrants) symbol test conditions quadrant qxx08xh3 qxx08xh4 unit i gt v d = 12v r l 8 * o * * o * * * max. 10 ma v gt * o * * o * * * max. v v gd v d = v drm r l l 8 t j = 125c * o * * o * * * . * / 0.2 v i ) i t = 100ma max. 15 ma dv/dt v d = v drm gate open t j = 125c 2 y y - ) z 2 y y 3 ) z 2 y y / ) z . * / 400v 400 v/s 7 50 800v 200 1000v 100 2 y y 7 ) z 2 y y % ) z 400v 450 7 50 800v 250 1000v 150 (dv/dt)c e j e u d " n t 5 j = 125c . * / 20 25 v/s t gt i g = 100ma pw = 15s i t " q l typ. 4.0 4.0 s / p u f y y w p m u b h f y q b d l b h f z t f o t j u j w j u z 79 ?2010 littelfuse, inc revised: july 29, 2010 12:24 pm teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. teccor ? brand thyristors lxx08xx & qxx08xx & qxx08xhx series 8 amp sensitive, standard & alternistor (high commutation) triacs 8.0a triacs static characteristics symbol test conditions value unit v tm i tm " u p ? t max. v i drm i rrm v drm = v rrm - y y y z t j = 25c 7 max. 20 a t j = 110c 7 0.5 ma 2 y y y z t j = 25c 400 - 1000v 50 a t j = 125c 400 - 800v 2 ma t j = 100c 1000v 2 y y y ) z t j = 25c 400 - 800v 10 a 1000v 20 t j = 125c 400 - 800v 2 ma t j = 100c 1000v thermal resistances symbol parameter value unit r r (j-c) junction to case (ac) - 2 y y 3 z z - 2 y y / z z 1. 5 c/w - 2 y y - z z 2.8 - 2 y y 7 z z 2.1 r r (j-a) junction to ambient - 2 y y 3 z z 45 c/w - 2 y y - z z 50 - 2 y y 7 z z / p u f y y w p m u b h f y q b d l b h f z t f o t j u j w j u z z z u z q f t f o t j u j w j u z figure 2: normalized dc gate trigger current for all quadrants vs. junction temperature junction temperature (t j )- oc -6 5 -40 -1 5 10 3 5 60 8 5 110 12 5 0.0 ratio of i gt i gt (t j = 2 5 c) 0. 5 1.0 1. 5 2.0 2. 5 3.0 3. 5 figure 1: de?nition of quadrants / p u f " m u f s o j t u p s t x j m m o p u p q f s b u f j o 2 * 7 mt2 positive (positive half cycle) mt2 negative (negative half cycle) mt1 mt2 + i gt ref qii mt1 i gt gate mt2 ref mt1 mt2 ref mt1 mt2 ref qi qiv qiii all polarities are referenced to mt1 ( - ) i gt gate (+) i gt - i gt gate ( - ) i gt gate (+) + - 80 revised: july 29, 2010 12:24 pm ?2010 littelfuse, inc teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. 8 amp sensitive, standard & alternistor (high commutation) triacs lxx08xx & qxx08xx & qxx08xhx series figure 3: normalized dc holding current vs. junction temperature figure 4: normalized dc gate trigger voltage for all quadrants vs. junction temperature junction temperature (t j )- oc -6 5 -40 -1 5 10 3 5 60 8 5 110 1 2 5 0.0 ratio of i h i h (t j = 2 5 c) 0. 5 1. 0 1. 5 2.0 2. 5 3.0 3. 5 junction temperature (t j )- oc ratio of v gt v gt (t j = 2 5 c) -6 5 -40 -1 5 10 3 5 60 8 5 110 1 2 5 0.0 0. 5 1. 0 1. 5 2.0 figure 7: maximum allowable case temperature vs. on-state current (standard / alternistor triac) figure 8: on-state current vs. on-state voltage (typical) 0.6 0.8 1.0 1.2 1.4 1.6 20 16 12 8 4 0 t c = 2 5 c postitive or negative instantaneous on-state voltage (v t ) - volts postitive or negative instantaneous on-state current (i t ) - amps rms on-state current (i t(rms) ) - amps 0246810 0 2 4 6 8 10 12 14 16 18 average on-state power dissipation (p d(av) ) - watts figure 5: power dissipation (typical) vs. rms on-state current figure 6: maximum allowable case temperature vs. on-state current (sensitive triac) rms on-state current (i t(rms) ) - amps 01234 5 678 60 6 5 70 7 5 80 8 5 90 9 5 100 10 5 110 maximum allowable case temperature (t c ) - c lxx08vy lxx08dy lxx08ry lxx08ly current waveform: sinusoidal load: resistive or inductive conduction angle: 360 case temperature: measured as shown on dimensional drawings rms on-state current (i t(rms) ) - amps 60 70 80 90 100 110 120 130 maximum allowable case temperature (t c ) - c 01234 5 678 qxx08lyy qxx08ryy qxx08nyy qxx08vyy qxx08dyy / p u f y y w p m u b h f y q b d l b h f z t f o t j u j w j u z z z u z q f t f o t j u j w j u z 81 ?2010 littelfuse, inc revised: july 29, 2010 12:24 pm teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. teccor ? brand thyristors lxx08xx & qxx08xx & qxx08xhx series 8 amp sensitive, standard & alternistor (high commutation) triacs 8.0a triacs surge current duration- full cycles 1 peak surge (non-repetitive) on-state current (i tsm ) - amps 1 10 100 1000 10 100 l/qxx08ryy l/qxx08lyy l/qxx08nyy l/qxx08vyy l/qxx08dyy figure 10: surge peak on-state current vs. number of cycles 4 6 1 1 - : ' 3 & 2 6 & / $ : ) [ 4 j o v t p j e b m load: resistive rms on-state current: [i t(rms) > . b y j n v n 3 b u f e value at speci?ed case temperature / p u f t 1. gate control may be lost during and immediately following surge current interval. 2. overload may not be repeated until junction temperature has returned to steady-state rated value. figure 9: maximum allowable ambient temperature vs. on-state current rms on-state current (i t(rms) ) - amps 20 40 60 80 100 120 maximum allowable ambient temperature (t a ) - c 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 current waveform: sinusoidal load: resistive or inductive conduction angle: 360 free air rating - no heatsink l/qxx08lyy l/qxx08ryy l/qxx08vyy / p u f y y w p m u b h f y q b d l b h f z t f o t j u j w j u z z z u z q f t f o t j u j w j u z 82 revised: july 29, 2010 12:24 pm ?2010 littelfuse, inc teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. 8 amp sensitive, standard & alternistor (high commutation) triacs lxx08xx & qxx08xx & qxx08xhx series soldering parameters re?ow condition 1 c o ' s f f b t t f n c m z pre heat - temperature min (t s(min) ) 150c - temperature max (t s(max) ) 200c - time (min to max) (t s ) o t f d t average ramp up rate (liquidus temp) (t l ) to peak ? $ t f d p o e n b y t s(max) to t l - ramp-up rate ? $ t f d p o e n b y re?ow - temperature (t l ) (liquidus) ? $ - temperature (t l ) o t f d p o e t peak temperature (t p ) +0/-5 c time within 5c of actual peak temperature (t p ) o t f d p o e t ramp-down rate ? $ t f d p o e n b y time 25c to peak temperature (t p ) n j o v u f t . b y do not exceed 280c physical speci?cations environmental speci?cations test speci?cations and conditions ac blocking (v drm ) . * - 4 5 % . $ p o e " " q q m j f e peak ac voltage @ 125c for 1008 hours temperature cycling . * - 4 5 % . 100 cycles; -40c to +150c; 15-min dwell-time temperature/ humidity & * " + & % & $ + & 4 % " i p v s t 7 % $ ? $ rel humidity high temp storage . * - 4 5 % . 1008 hours; 150c low-temp storage 1008 hours; -40c thermal shock . * - 4 5 % . 10 cycles; 0c to 100c; 5-min dwell- u j n f b u f b d i u f n q f s b u v s f t f d n b y transfer time between temperature autoclave & * " + & % & $ + & 4 % " i p v s t ? $ b u " 5 . t b o e 3 ) resistance to solder heat . * - 4 5 % . f u i p e solderability " / 4 * + 4 5 % d b u f h p s z 5 f t u " lead bend . * - 4 5 % . $ p o e & terminal finish . b u u f 5 j o q m b u f e body material 6 - s f d p h o j [ f e f q p y z n f f u j o h n b n n b c j m j u z d m b t t j m d b u j p o 7 terminal material copper alloy design considerations careful selection of the correct device for the applications operating parameters and environment will go a long way u p x b s e f y u f o e j o h u i f p q f s b u j o h m j g f p g u i f 5 i z s j t u p s ( p p e e f t j h o q s b d u j d f t i p v m e m j n j u u i f n b y j n v n d p o u j o v p v t d v s s f o u u i s p v h i u i f n b j o u f s n j o b m t u p p g u i f e f w j d f rating. other ways to ensure long life for a power discrete semiconductor are proper heat sinking and selection of voltage ratings for worst case conditions. overheating, overvoltage (including dv/dt), and surge currents are the main killers of semiconductors. correct mounting, soldering, and forming of the leads also help protect against component damage. time temperature t p t l t s(max) t s(min) 25 t p t l t s time to peak temperature preheat p reheat ramp-up ramp-up ramp-down r amp- do 83 ?2010 littelfuse, inc revised: july 29, 2010 12:24 pm teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. teccor ? brand thyristors lxx08xx & qxx08xx & qxx08xhx series 8 amp sensitive, standard & alternistor (high commutation) triacs 8.0a triacs dimensions to-220ab (r-package) non-isolated mounting tab common with center lead dimension inches millimeters min max min max a 0.420 b 0.105 0.115 c 0.250 5.84 d & 0.142 ' 0.110 g 0.540 ) 0.025 j 0.205 5.21 k 0.105 2.41 l 1.52 m 0.085 2.41 / 0.018 0.024 o 0.188 4.52 p 0.045 1. 14 1. 5 2 r 0.048 1.22 dimensions to-220ab (l-package) isolated mounting tab dimension inches millimeters min max min max a 0.420 b 0.105 0.115 c 0.250 5.84 d & 0.142 ' 0.110 g 0.540 ) 0.025 j 0.205 5.21 k 0.105 2.41 l 1.52 m 0.085 2.41 / 0.018 0.024 o 0.188 4.52 p 0.045 1. 14 1. 5 2 r 0.048 1.22 k j a h g b f e c d l r t c measuring point area (ref.) 0.17 in 2 mt2 o p n m mt1 gate .320 8.13 . 5 26 13.36 .276 7. 0 1 k j a h g b f e c d l r t c measuring point mt2 mt2 o p n m mt1 .276 7. 0 1 . 5 26 13.36 .320 8.13 gate area (ref.) 0.17 in 2 notch in gate lead to id. non-isolated tab / p u f . b y j n v n u p s r v f u p be applied to mounting tab j t j o m c t / n / p u f . b y j n v n u p s r v f u p be applied to mounting tab j t j o m c t / n 84 revised: july 29, 2010 12:24 pm ?2010 littelfuse, inc teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. 8 amp sensitive, standard & alternistor (high commutation) triacs lxx08xx & qxx08xx & qxx08xhx series dimensions to-263ab (n-package) d 2 -pak surface mount dimensions to-251aa (v-package) v-pak through hole dimension inches millimeters min typ max min typ max a 0.040 0.044 0.050 1.02 1.11 b 0.242 0.245 c d 0.205 0.208 5.21 5.41 & 0.255 ' 0.80 0.84 g 2.21 2.28 ) 0.085 2.41 i 0.180 0.184 j 0.018 0.020 0.51 0.58 k 0.040 0.044 1. 01 1. 12 l 0.018 0.020 0.52 0.58 p 0.042 0.052 1.20 q 0.044 1. 0 0 1. 11 r 0.044 1. 0 0 1. 11 s 0.084 2.00 2.11 dimension inches millimeters min . b y min . b y a b 0.420 c 0.188 4.52 d 0.025 & 0.045 1. 14 1. 5 2 ' 1.52 g 0.105 2.41 ) 0.102 j 0.018 0.024 k 0.110 s 15.88 v 0.045 1. 14 u 0.002 0.010 0.05 0.25 w 0.040 1.02 g b a w v s mt1 mt2 t c measuring point c e k h j u .320 8.13 .276 7. 0 1 .331 8.41 gate .460 11.68 .66 5 16.89 .260 6.60 .1 5 0 3.81 .080 2.03 .08 5 2.16 .0 55 1.40 .3 5 0 8.89 .276 7. 0 1 .276 7. 0 1 area: 0.11 in 2 d f area: 0.040 in 2 t c measuring point gate g i e d a b c f j h k l 5 .28 .208 5 .34 .210 mt2 mt1 mt2 p q r s 85 ?2010 littelfuse, inc revised: july 29, 2010 12:24 pm teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. teccor ? brand thyristors lxx08xx & qxx08xx & qxx08xhx series 8 amp sensitive, standard & alternistor (high commutation) triacs 8.0a triacs dimensions to-252aa (d-package) d-pak surface mount dimension inches millimeters min typ max min typ max a 0.040 0.050 1.02 b 0.245 c 0.108 d 0.205 0.208 5.21 5.41 & 0.255 ' 0.80 0.84 g 2.21 2.28 ) 0.085 2.41 i 0.184 4.55 j 0.018 0.020 0.51 0.58 k 0.040 0.044 1.02 1.12 l 0.018 0.020 0.51 0.58 m 0.000 0.000 0.004 0.00 0.00 0.10 / 0.021 o005005 p 0.042 0.052 1.20 q 0.044 1. 0 0 1. 11 m o n h j l k .118 3 .063 1.60 .071 1.80 .264 6.71 .264 6.71 .181 4.60 gate mt2 mt1 mt2 t c measuring point g i d e a b c f 5 .28 .208 5 .34 .210 : 0.040 in 2 area p q 86 revised: july 29, 2010 12:24 pm ?2010 littelfuse, inc teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. 8 amp sensitive, standard & alternistor (high commutation) triacs lxx08xx & qxx08xx & qxx08xhx series product selector part number voltage (xx) gate sensitivity quadrants type package 400v 600v 800v 1000v i C ii C iii iv - y y - x x 5 ma 10 ma sensitive triac to-220l - y y % x x 5 ma 10 ma sensitive triac to-252 d-pak - y y 3 x x 5ma 10ma sensitive triac to-220r - y y 7 x x 5 ma 10 ma sensitive triac to-251 v-pak - y y - x x 10 ma 20 ma sensitive triac to-220l - y y % x x 10 ma 20 ma sensitive triac to-252 d-pak - y y 3 x x 10ma 20ma sensitive triac to-220r - y y 7 x x 10 ma 20 ma sensitive triac to-251 v-pak 2 y y 3 ) x x 10 ma alternistor triac to-220r 2 y y 7 ) x x 10 ma alternistor triac to-251 v-pak 2 y y % ) x x 10 ma alternistor triac to-252 d-pak 2 y y / ) x x 10 ma alternistor triac 5 0 % 2 -pak 2 y y - x 25 ma triac to-220l 2 y y 3 x 25 ma triac to-220r 2 y y / x 25 ma triac 5 0 % 1 " , 2 y y - ) xxx x n " alternistor triac to-220l 2 y y 3 ) xxx x n " alternistor triac to-220r 2 y y 7 ) xxx x n " alternistor triac to-251 v-pak 2 y y % ) xxx x n " alternistor triac to-252 d-pak 2 y y / ) xxx x n " alternistor triac 5 0 % 1 " , 2 y y - x x x 50 ma triac to-220l 2 y y 3 x x x 50 ma triac to-220r 2 y y / x x x 50 ma triac 5 0 % 1 " , packing options part number marking weight packing mode base quantity - 2 y y - 3 z z - 2 y y - 3 z z 2.2 g bulk 500 - 2 y y - 3 z z 5 1 - 2 y y - 3 z z 2.2 g tube pack 500 (50 per tube) 2 y y / z z 5 1 2 y y / z z h tube 500 (50 per tube) 2 y y / z z 3 1 2 y y / z z h & n c p t t f e $ b s s j f s 500 - 2 y y % z z 5 1 - 2 y y % z z h tube q f s u v c f - 2 y y % z z 3 1 - 2 y y % z z h & n c p t t f e $ b s s j f s 2500 - 2 y y 7 z z 5 1 - 2 y y 7 z z 0.4 g tube q f s u v c f / p u f y y w p m u b h f y q b d l b h f z t f o t j u j w j u z z z u z q f t f o t j u j w j u z 87 ?2010 littelfuse, inc revised: july 29, 2010 12:24 pm teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. teccor ? brand thyristors lxx08xx & qxx08xx & qxx08xhx series 8 amp sensitive, standard & alternistor (high commutation) triacs 8.0a triacs 0.512 (13.0) arbor hole dia. dc xxxxxx xxxxxx dc xxxxxx dc xxxxxx xx xx xx gate mt1 mt2 0.63 (16.0) 0.157 (4.0) 0.64 (16.3) 12.99 (330.0) 0.524 (13.3) 0.315 (8.0) 0.059 dia (1.5) * * cover tape direction of feed dimensions are in inches (and millimeters). gate mt1 mt2 0.512 (13.0) arbor hole dia. 0.945 (24.0) 0.63 (16.0) 1.01 (25.7) 12.99 (330.0) 0.827 (21.0) 0.157 (4.0) direction of feed dimensions are in inches (and millimeters). * * cover tape 0.059 dia (1.5) to-252 embossed carrier reel pack (rp) speci?cations meets all eia-481-2 standards to-263 embossed carrier reel pack (rp) speci?cations meets all eia-481-2 standards 88 revised: july 29, 2010 12:24 pm ?2010 littelfuse, inc teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. 8 amp sensitive, standard & alternistor (high commutation) triacs lxx08xx & qxx08xx & qxx08xhx series current 08: 8a sensitivity & type sensitive triac: 6 : 5 ma (qi, ii, iii) 10 ma (qiv) 8 : 10 ma (qi, ii, iii) 20 ma (qiv) standard triac: 4 : 2 5 ma (qi, ii, iii) 5 : 5 0 ma (qi, ii, iii) alternistor triac: h3 : 10 ma (qi, ii, iii) h 4 : 3 5 ma (qi, ii, iii) package type l : to-220 isolated r : to-220 non-isolated n : to-263 (d 2 pak) v : to-2 5 1 (vpak) d : to-2 5 2 (dpak) voltage rating 4 0 : 400v 60 : 600v 80 : 800v k0 : 1000v lead form dimensions xx : lead form option q 60 08 l 5 5 6 device type l : sensitive triac q : triac or alternistor part numbering system part marking system ? l6008v5 yxxxx to-252aa C (d package) to-251aa C (v package) ? |
Price & Availability of QXX08RH4
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |