1 ? fn7388 caution: these devices are sensitive to electrostatic discharge; follow proper ic handling procedures. 1-888-intersil or 321-724-7143 | intersil (and design) is a registered trademark of intersil americas inc. copyright ? intersil americas inc. 2003. all rights reserved. elantec is a registered trademark of elantec semiconductor, inc. all other trademarks mentioned are the property of their respective owners. preliminary el5162, EL5163, el5262, el5263, el5362 300mhz current feedback amplifiers with enable the el5162, EL5163, el5262, el5263, and el5362 are current feedback amplifiers with a bandwidth of 300mhz. this makes these amplifiers ideal for today?s high speed video and monitor applications. with a supply current of just 1.5ma and the ability to run from a single supply voltage from 5v to 12v, these amplifiers are also ideal for hand held, portable or battery-powered equipment. the el5162 also incorporates an enable and disable function to reduce the supply current to 100a typical per amplifier. allowing the ce pin to float or applying a low logic level will enable the amplifier. the EL5163 is offered in a 5-pin sot-23 package, the el5162 in a 6-pin sot-23 and industry-standard 8-pin so packages, the el5262 in a 10-pin msop package, the el5263 in 8-pin so and msop packages, and the el5362 in 16-pin so and qsop packages. all operate over the industrial temperature range of -40c to +85c. features 500mhz -3db bandwidth 4000v/s slew rate 1.5ma supply current single and dual supply operation, from 5v to 12v supply span fast enable/disable (el5162 only) available in sot-23 packages high speed, 1.4ghz product available (el5167 & el5167) high speed, 5ma, 600mhz product available (el5164 & el5165) applications battery powered equipment handheld, portable devices video amplifiers cable drivers rgb amplifiers test equipment instrumentation current to voltage converters ordering information part number package tape & reel pkg. dwg. # part number package tape & reel pkg. dwg. # el5162is 8-pin so - mdp0027 el5263iy (note) 8-pin msop - mdp0043 el5162is-t7 8-pin so 7? mdp0027 el5263iy-t7 8-pin msop 7? mdp0043 el5162is-t13 8-pin so 13? mdp0027 el5263iy-t13 8-pin msop 13? mdp0043 el5162iw 6-pin sot-23 - mdp0038 el5263is (note) 8-pin so - mdp0027 el5162iw-t7 6-pin sot-23 7? mdp0038 el5263is-t7 8-pin so 7? mdp0027 el5162iw-t13 6-pin sot-23 13? mdp0038 el5263is-t13 8-pin so 13? mdp0027 EL5163iw 5-pin sot-23 - mdp0038 el5362is (note) 16-pin so - mdp0027 EL5163iw-t7 5-pin sot-23 7? mdp0038 el5362is-t7 16-pin so 7? mdp0027 EL5163iw-t13 5-pin sot-23 13? mdp0038 el5362is-t13 16-pin so 13? mdp0027 el5262iy (note) 10-pin msop - mdp0043 el5362iu (note) 16-pin qsop - mdp0040 el5262iy-t7 10-pin msop 7? mdp0043 el5362iu-t7 16-pin qsop 7? mdp0040 el5262iy-t13 10-pin msop 13? mdp0043 el5362iu-t13 16-pin qsop 13? mdp0040 note: duals and triples to be released october 2003 data sheet august 29, 2003
2 pinouts el5162 (8-pin so) top view el5162 (6-pin sot-23) top view EL5163 (5-pin sot-23) top view el5262 (10-pin msop) top view el5263 (8-pin so, msop) top view el5362 (16-pin so, qsop) top view 1 2 3 4 8 7 6 5 - + nc in- in+ vs- ce vs+ out nc 1 2 3 6 4 5 - + out vs- in+ vs+ in- ce 1 2 3 5 4 - + out vs- in+ vs+ in- 1 2 3 4 10 9 8 7 5 6 out in- in+ vs- vs+ out in- in+ ce ce 1 2 3 4 8 7 6 5 - + - + out1 in- in+ vs+ in- out2 vs- in+ 1 2 3 4 16 15 14 13 5 6 7 12 11 10 8 9 - + - + - + ina+ cea vs- ceb inb+ nc cec inc+ ina- outa vs+ outb inb- nc outc inc- el5162, EL5163, el5262, el5263, el5362
3 absolute maximum ratings (t a = 25c) supply voltage between v s + and v s - . . . . . . . . . . . . . . . . . . . 13.2v maximum continuous output current . . . . . . . . . . . . . . . . . . . 50ma operating junction temperature . . . . . . . . . . . . . . . . . . . . . . . 125c power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see curves pin voltages. . . . . . . . . . . . . . . . . . . . . . . . .v s - - 0.5v to v s + +0.5v storage temperature . . . . . . . . . . . . . . . . . . . . . . . . -65c to +150c operating temperature . . . . . . . . . . . . . . . . . . . . . . . -40c to +85c caution: stresses above those listed in ?absolute maximum ratings? may cause permanent damage to the device. this is a stress o nly rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. important note: all parameters having min/max specifications are guaranteed. typical values are for information purposes only. u nless otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: t j = t c = t a electrical specifications v s + = +5v, v s - = -5v, r f = 750 ? for a v = 1, r f = 400 ? for a v = 2, r l = 150 ? , t a = 25c unless otherwise specified. parameter description conditions min typ max unit ac performance bw -3db bandwidth a v = +1, r l = 500 ? 500 mhz a v = +2, r l = 150 ? 233 mhz bw1 0.1db bandwidth 30 mhz sr slew rate v o = -2.5v to +2.5v, a v = +2, r l = 100 ? 2800 4000 6000 v/s t s 0.1% settling time v out = -2.5v to +2.5v, a v = +1 25 ns e n input voltage noise 3nv/ hz i n - in- input current noise 10 pa/ hz i n + in+ input current noise 6.5 pa/ hz dg differential gain error (note 1) a v = +2 0.05 % dp differential phase error (note 1) a v = +2 0.15 dc performance v os offset voltage -5 -2 5 mv t c v os input offset voltage temperature coefficient measured from t min to t max 10 v/c r ol transimpedance 500 1000 k ? input characteristics cmir common mode input range 3 3.3 v cmrr common mode rejection ratio 50 62 75 db -icmr - input current common mode rejection -1 1 a/v +i in + input current -8 1 8 a -i in - input current -10 1.0 10 a r in input resistance 800 900 3000 k ? c in input capacitance 1pf output characteristics v o output voltage swing r l = 150 ? to gnd 3.35 3.6 3.75 v r l = 1k ? to gnd 3.75 3.9 4.15 v i out output current r l = 10 ? to gnd 60 100 180 ma supply i son supply current - enabled no load, v in = 0v 1.3 1.5 1.7 ma i soff supply current - disabled no load, v in = 0v -25 -14 -5 a el5162, EL5163, el5262, el5263, el5362
4 all intersil u.s. products are manufactured, asse mbled and tested utilizing iso9000 quality systems. intersil corporation?s quality certifications can be viewed at www.intersil.com/design/quality intersil products are sold by description only. intersil corporation reserves the right to make changes in circuit design, soft ware and/or specifications at any time without notice. accordingly, the reader is cautioned to verify that data sheets are current before placing orders. information furnishe d by intersil is believed to be accurate and reliable. however, no responsibility is assumed by intersil or its subsidiaries for its use; nor for any infringements of paten ts or other rights of third parties which may result from its use. no license is granted by implication or otherwise under any patent or patent rights of intersil or its subsidiari es. for information regarding intersil corporation and its products, see www.intersil.com psrr power supply rejection ratio dc, v s = 4.75v to 5.25v 65 77 db -ipsr - input current power supply rejection dc, v s = 4.75v to 5.25v -0.5 0.1 0.5 a/v enable (el5162 only) t en enable time 200 ns t dis disable time 800 ns i ihce ce pin input high current ce = v s + 5 15 25 a i ilce ce pin input low current ce = v s --101a v ihce ce input high voltage for power-down v s + - 1 v v ilce ce input low voltage for power-down v s + - 3 v note: 1. standard ntsc test, ac signal amplitude = 286mvp-p, f = 3.58mhz electrical specifications v s + = +5v, v s - = -5v, r f = 750 ? for a v = 1, r f = 400 ? for a v = 2, r l = 150 ? , t a = 25c unless otherwise specified. (continued) parameter description conditions min typ max unit el5162, EL5163, el5262, el5263, el5362
|
