data sheet luy9033/tr2 ligitek electronics co.,ltd. property of ligitek only surface mount tape and reel doc. no : qw0905-luy9033/tr2 rev. : a date : 18 - sep.- 2007 lead-free parts pb
ligitek electronics co.,ltd. property of ligitek only 1/7 page cathode 1.9 2.0 0.5 0.1 4.0 0.3 1.75 4.0 1.55 3.05 5.5 6.43 2.8 part no. package dimensions luy9033/tr2 0.4 0.1 0.7 carrier type dimensions polarity 9.3 12 0.3 note : 1.all dimension are in millimeter tolerance is 0.2mm unless otherwise noted. 2.specifications are subject to change without notice. note : the tolerances unless mentioned is 0.2mm,angle 0.5. unit=mm. 1.4 4.3 0.5 2.0 5.8 0.5 3.05 0.5 2.5
178 2.0 part no. luy9033/tr2 description 12.0mm tape,7"reel quantity/reel 1500 devices 14.2 1.0 74.0 1.5 16.0 1.0 reel dimensions page2/7 ligitek electronics co.,ltd. property of ligitek only part no. : luy9033/tr2
electrostatic discharge esd2000 v min. 550 max 260 for 5 sec max (2mm from body) luminous intensity @20ma(mcd) color water clear note : 1.the forward voltage data did not including 0.1v testing tolerance. 2. the luminous intensity data did not including 15% testing tolerance. luy9033/tr2 part no emitted algainpyellow material dominant wave length dnm lens 595 max. min. 1.7 152.6 forward voltage @20 ma(v) spectral halfwidth nm typical electrical & optical characteristics (ta=25 ) storage temperature soldering temperature operating temperature tstg tsol t opr -40 ~ +100 -40 ~ +85 typ. 20 900 viewing angle 2 1/2 (deg) ligitek electronics co.,ltd. property of ligitek only absolute maximum ratings at ta=25 reverse current @5v power dissipation peak forward current duty 1/10@10khz forward current parameter ir pd i fp i f 10 120 90 50 symbol ratings uy a mw ma ma unit page3/7 part no. : luy9033/tr2
ambient temperature( ) fig.4 relative intensity vs. temperature r e l a t i v e i n t e n s i t y @ 2 0 m a wavelength (nm) 500 0 0.5 550600650 ambient temperature( ) fig.5 relative intensity vs. wavelength fig.3 forward voltage vs. temperature f o r w a r d v o l t a g e @ 2 0 m a n o r m a l i z @ 2 5 -20 1.0 -40 0.8 20 060 40 1.0 0.9 1.1 1.2 0.5 r e l a t i v e i n t e n s i t y @ 2 0 m a n o r m a l i z e @ 2 5 100 80-40-20 0 020 3.0 2.5 2.0 1.5 1.0 80 60 40100 ligitek electronics co.,ltd. property of ligitek only fig.2 relative intensity vs. forward current forward current(ma) 4.0 fig.1 forward current vs. forward voltage typical electro-optical characteristics curve 100 f o r w a r d c u r r e n t ( m a ) 0.1 1.0 10 1.0 forward voltage(v) 2.03.0 1000 uy chip r e l a t i v e i n t e n s i t y n o r m a l i z e @ 2 0 m a 2.0 1.5 1.0 0.5 5.0 0 1.010 3.0 2.5 page4/7 1001000 part no. : luy9033/tr2
120 sec.max. above 220 c 60 sec.max. 4. pb-free reflow solder preheat 180~200 c 1~5 c/sec 1~5 c/sec 260 c max. 10sec.max time cooling -5 /sec 240 150 120 preheat rising +5 /sec temp. ( ) 3. lead reflow solder 1. hand solder basic spec is Q 280 3 sec one time only. preheat 2. wave solder 245 5 within 5 sec ligitek electronics co.,ltd. property of ligitek only recommended soldering conditions page 5/7 note:1.wave solder and reflow soldering should not be made more than one time. 2.you can just only select one of the soldering conditions as above. part no. 60 ~ 120 sec 120 ~ 180 sec 120 ~ 150 5sec soldering heat max. 260 luy9033/tr2
luy9033/tr2 part no. cleaning: use alcohol-based cleaning solvents such as isopropyl alcohol to clean the led. (a) recommended circuit. (b) the difference of brightness between led could be found due to the vf-if characteristics of led. esd(electrostatic discharge): static electricity or power surge will damage the led. use of a conductive wrist band or anti-electrosatic glove is recommended when handing these led. all devices, equipment and machinery must be properly grounded. led led circuit model a drive method: led is a current operated device, and therefore, requirer some kind of current limiting incorporated into the driver circuit. this current limiting typically takes the form of a current limiting resistor placed in series with the led. consider worst case voltage variations than could occur across the current limiting resistor. the forwrd current should not be allowed to change by more than 40% of its desired value. precautions for use: storage time: 1.the operation of temperatures and rh are : 5 ~35 ,rh<60%. 2.once the package is opened, the products should be used within a week. otherwise, they should be kept in a damp proof box with descanting agent. considering the tape life, we suggest our customers to use our products within a year(from production date). 3.if opened more than one week in an atmosphere 5 ~ 35 ,rh<60%, they should be treated at 60 5 fo r 15hrs. circuit model b ligitek electronics co.,ltd. property of ligitek only page 6/7
luy9033/tr2 part no. 1.t.sol=235 5 2.immersion time 2 0.5sec 3.coverage R 95% of the dipped surface solderability test mil-std-202f: 208d mil-std-750d: 2026 mil-std-883d: 2003 iec 68 part 2-20 jis c 7021: a-2 mil-std-750d:2031.2 j-std-020 mil-std-202f: 107d mil-std-750d: 1051 mil-std-883d: 1010 jis c 7021: a-4 environmental test ir reflow temperature cycling 1.105 ~ 25 ~ - 55 ~ 25 30mins 5mins 30mins 5mins 2.10 cyeles 1.t=260 xc max. 10sec.max. 2. 6 min mil-std-202f: 107d mil-std-750d: 1051 mil-std-883d: 1011 jis c 7021: b-12 mil-std-202f:103b jis c 7021: b-11 mil-std-750d: 1026 mil-std-883d: 1005 jis c 7021: b-1 mil-std-883d:1008 jis c 7021: b-10 page ligitek electronics co.,ltd. property of ligitek only 1.ta=under room temperature as per data sheet maximum rating. 2.if=20ma 3.t=1000 hrs (-24hrs, +72hrs) thermal shock test high temperature high humidity storage test endurance test high temperature storage test low temperature storage test operating life test 1.ta=105 5 &-40 5 (10min) (10min) 2.total 10 cycles 1.ta=65 5 2.rh=90%~95% 3.t=1000hrs 2hrs 1.ta=-40 5 2.t=1000 hrs (-24hrs, +72hrs) 1.ta=105 5 2.t=1000 hrs (-24hrs, +72hrs) classification reliability test: test item test condition reference standard 7/7
|
