specification model elp-75-3.3 elp-75-12 elp-75-5 elp-75-15 elp-75-24 elp-75-48 dc voltage rated current current range rated power output voltage adj. range line regulation load regulation setup, rise time hold up time (typ.) voltage range note.6 frequency range power factor (typ.) note.5 efficiency (typ.) ac current (typ.) input inrush current (typ.) leakage current safety standards working temp. working humidity storage temp., humidity temp. coefficient vibration mtbf dimension others note packing over load over voltage 3.3v 12v 5v 15v 24v 48v 15a 6.25a 15a 5a 3.15a 1.6a 0 ~ 15a 0 ~ 6.25a 0 ~ 15a 0 ~ 5a 0 ~ 3.15a 0 ~ 1.6a 49.5w 75w 75w 75w 75.6w 76.8w 80mvp-p 120mvp-p 80mvp-p 150mvp-p 240mvp-p 300mvp-p 3 ~ 3.6v 10.8 ~ 13.2v 4.75 ~ 5.5v 13.5 ~ 16.5v 21.6 ~ 26.4v 43.2 ~ 52.8v 3.0% 0.5% 2.0% 2500ms, 50ms/230vac 2500ms, 50ms/115vac at full load 20ms/230vac 20ms/115vac at full load 90 ~ 264vac 127 ~ 370vdc 47 ~ 63hz 3.3v: pf>0.95/230vac pf>0.98/115vac at full load pf>0.91/230vac 5v~48v: 3.7 ~ 4.45v 5.6 ~ 6.75v 13.8 ~ 16.2v 17.25 ~ 20.25v 27.6 ~ 32.4v 53.3 ~ 64.8v 80% 89% 82% 90% 90% 90% 1.8a/115vac 1 a/230vac cold start 60a/230vac 105 ~ 150% rated output power compliance to en55022 (cispr22) class b, en61000-3-2,-3 -30 ~ +70 (refer to "derating curve") 20 ~ 90% rh non-condensing -40 ~ +85 , 10 ~ 95% rh 0.03%/ (0 ~ 50 ) 10 ~ 500hz, 2g 10min./1cycle, period for 60min. each along x, y, z axes 345.3khrs min. mil-hdbk-217f (25 ) pcb: with optional case:195*68.5*33mm (l*w*h) 175*60*27mm (l*w*h) 75w single output with pfc function e l p - 7 5 s e r i e s withstand voltage isolation resistance i/p-o/p, i/p-fg, o/p-fg:100m ohms / 500vdc/ 500vdc / 25 / 70% rh environment safety & emc (note 4) protection 1. all parameters not specially mentioned are measured at 230vac input, r ated load and 25 of ambient temperature. 2. ripple & noise are measured at 20mhz of bandwidth by using a 12" twisted pair- wire terminated with a 0.1uf & 47uf parallel capacitor. 3. tolerance : includes set up tolerance, line regulation and load regula tion. 4. the power supply is considered a component which will be installed into a fi nal equipment. the final equipment must be re-confirmed that it still me ets emc directives. 5. 3.3v pf>0.92/230vac, others pf>0.95/230vac. 6. derating may be needed under low input voltage. please check the deratin g curve for more details. for guidance on how to perform these emc tests, please refer to ?emi testing of c omponent power supplies.? (as available on http://www.meanwell.com) ripple & noise (max.) note.2 voltage tolerance note.3 features : protection type : hiccup mode, recovers automatically after fault con dition is removed protection type : shut down o/p voltage, re-power on to recover ul60950-1, tuv en60950-1 approved compliance to , heavy industry level, criteria a en61000-4-2,3,4,5,6,8,11; en55024 universal ac input / full rangeprotections: short circuit / overload / over voltage cooling by free air convection 3 years warranty optional l-bracket and cover (elp-75-x-c, x=3.3,5,12,15,24,36,48) built-in active pfc function, pf>0.95high efficiency up to 90% 1u low profile led indicator for power on no load power consumption<0.5w <1ma/240vac i/p-o/p:3kvac i/p-fg:1.5kvac o/p-fg:0.5kvac pcb:0.25kg; 48pcs/13kg/0.85cuft with optional case:0.54kg; 2 5pcs/14.5kg/0.59cuft file name:elp-75-spec 2011-05-09 2.0% 0.5% 1.5% 2.0% 0.5% 1.0% 2.0% 0.5% 1.0% 1.0% 0.5% 1.0% 1.0% 0.5% 1.0% elp-75-36 36v 2.1a 0 ~ 2.1a 75.6w 280mvp-p 32.4 ~ 39.6v 1.0% 0.5% 1.0% 90% 39.7 ~ 46.8v emc immunity emc emission
mechanical specification unit:mm block diagram circuit detection o.l.p. emi filter rectifier & pfc circuit power switching filter & rectifiers +v -v i/p fg control o.v.p. fosc : 100khz file name:elp-75-spec 2011-05-09 optional l-bracket: no. 996a-d 9 optional cover: no. 996a-t 75w single output with pfc function e l p - 7 5 s e r i e s dc output connector (cn2) : jst b6p-vh or equivalent pin no. 1,2,3 4,5,6 assignment -v +v mating housing jst vhr or equivalent terminal jst svh-21t-p1.1 or equivalent ac input connector (cn1) : jst b3p-vh or equivalent pin no. 12 3 assignment ac/l no pin ac/n mating housing jst vhr jst svh-21t-p1.1 or equivalent or equivalent terminal output derating vs input voltage input voltage (vac) 60hz 90 100 95 120 115 160 140 200 180 240 220 264 load (%) ta=25 90 100 80 70 60 50 40 output derating ambient temperature ( ) load (%) -30 0 -20 20 10 30 40 20 40 80 60 100 60 50 70 (horizontal) others 3.3v,5v 115vac 230vac 25 25 9 4-m3 5 185 195 2- 4 4 16 2-m3 5 10.6 163.8 68.5 25 25 33 10.6 7 4 t2.5a/250v svr1 led1 fs1 cn1 12 3 cn2 24 35 6 1 5 165 175 5 50 60 4- 3.8 27 3max.
|
