gaas spst absorptive switch with asic driver dc - 3.0 ghz sw65-0014 north america: tel. (800) 366-2266, fax (800) 618-8883 asia/pacific: tel.+81-44-844-8296, fax +81-44-844-8298 europe: tel. +44 (1344) 869 595, fax+44 (1344) 300 020 specifications subject to change without notice. visit www.macom.com for additional data sheets and product information. v 3.00 features ? typical isolation: 42 db (2,000 mhz) ? typical insertion loss: 1.8 db (2,000 mhz) ? integral asic ttl/cmos driver ? plastic, 50 mil pitch, sow-24 lead, wide body ? low dc power consumption ? 50 ohm nominal impedance ? tape and reel packaging available ? test boards available description m/a-com's sw65-0014 is a gaas mmic absorptive spst switch with an integral silicon asic driver. this device is in a 24-lead plastic package. this switch offers excellent broadband performance and repeatability from dc to 3 ghz, while maintaining low dc power dissipation. the sw65-0014 is ideally suited for wireless infrastructure applications. also available in ceramic package with improved performance. sow-24 package outline conforms to jedec standard ms-013ad. 1. check with factory for available quantities and reel size. part number package sw65-0014 bulk packaging SW65-0014-TR tape and reel 1 sw65-0014-tb units mounted on test board ordering information electrical specifications: t a = +25c parameter test conditions units min typical max insertion loss dc - 3.0 ghz db ? 1.8 2.2 isolation (all arms off) dc - 3.0 ghz db 35 42 ? vswr dc - 3.0 ghz ? ? on off 1.6:1 2.0:1 2.1:1 t rise t fall t on t off transients 10%/90%, 90%/10% 2 50% ttl to 90%/10% rf in-band (peak to peak) ns ns mv ?- ? ? 15 50 50 50 150 150
gaas spst absorptive switch with asic driver dc - 3.0 ghz sw65-0014 north america: tel. (800) 366-2266, fax (800) 618-8883 asia/pacific: tel.+81-44-844-8296, fax +81-44-844-8298 europe: tel. +44 (1344) 869 595, fax+44 (1344) 300 020 specifications subject to change without notice. visit www.macom.com for additional data sheets and product information. v 3.00 pin configuration parameter test conditions units min typical max 1 db compression .05 ghz .5 - 3.0 ghz dbm dbm ? ? +20 +27 ? ? input ip 3 two tone inputs 0.05 ghz up to +5 dbm 0.5 - 3.0 ghz dbm dbm ? ? +35 +46 ? ? v cc ? v +4.5 +5.0 +5.5 v ee ? v -8.0 -5.0 -4.75 i cc v cc = +5.0v ma ? ? 4 i ee v ee = -5.0v ma ? ? -1 logic ?0? i in = 20a max v 0.0 ? 0.8 logic ?1? i in = 20a max v 2.0 ? 5.0 absolute maximum ratings 3,4 parameter absolute maximum max. input power 0.05 ghz 0.5 - 3.0 ghz +27 dbm +34 dbm bias voltages v ee v cc control voltage -8.5v +5.5v -0.5v to v cc +0.5v operating temperature -40c to +85c storage temperature -65c to +125c electrical specifications: t a = +25c ttl control input rf common to: c1 rf1 1 on 0 off truth table 2. decoupling capacitors (.01 f) are required on the power supply lines. 3. operation of this device above any one of these parameters may cause permanent damage. 4. when the rf input is applied to the terminated port, the absolute maximum power is +30 dbm. pin # function pin # function 1 rfc 13 c1 2 gnd 14 gnd 3 gnd 15 gnd 4 gnd 16 gnd 5 gnd 17 gnd 6 gnd 18 gnd 7 gnd 19 rf1 8 v ee 20 gnd 9 gnd 21 gnd 10 v cc 22 gnd 11 gnd 23 gnd 12 gnd 24 gnd
|
