View B201SW01V0_1998292.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

au optronics corporation product specification document version 0.4 1/35 ( v) preliminary specifications ( ) final specifications module 20.1? wsxga+ color tft-lcd model name b201sw01 v0 customer date checked & approved by date note: this specification is subject to change witho ut notice. approved by date beyond yang 5/16/2007 prepared by date cl wu 2007/5/8 nbbu marketing division / au optronics corporation www..net
au optronics corporation product specification document version 0.4 2/35 contents 1. handling precautions............................ ................................................... ........ 4 2. general description............................. ................................................... .......... 4 2.1 display characteristics ........................ ................................................... ........................... 5 2.2 optical characteristics ........................ ................................................... ............................ 6 3. functional block diagram........................ ................................................... ... 11 4. absolute maximum ratings........................ ................................................... 12 4.1 tft lcd module ................................. ................................................... ......................... 12 4.2 backlight unit................................. ................................................... ............................... 12 4.3 absolute ratings of environment................ ................................................... .................. 12 5. electrical characteristics ...................... ................................................... ...... 13 5.1 tft lcd module ................................. ................................................... ......................... 13 5.2 backlight unit................................. ................................................... ............................... 15 6. signal characteristic ........................... ................................................... ........ 17 6.1 pixel format image............................. ................................................... .......................... 17 6.2 the input data format.......................... ................................................... .......................... 18 6.3 signal description............................. ................................................... ............................ 19 6.4 interface timing ............................... ................................................... ............................. 21 6.5 power on/off sequence .......................... ................................................... .................. 23 7. connector & pin assignment ...................... .................................................. 2 4 7.1 tft lcd module ................................. ................................................... ......................... 24 7.2 backlight unit................................. ................................................... ............................... 24 7.3 signal for lamp connector...................... ................................................... ...................... 24 8. vibration and shock test........................ ................................................... .... 25 8.1 vibration test ................................. ................................................... ............................... 25 8.2 shock test spec: ............................... ................................................... ........................... 25 9. reliability..................................... ................................................... ................. 26 10. mechanical characteristics ..................... ................................................... . 27 10.1 lcm outline dimension......................... ................................................... ..................... 27 10.2 screw hole depth and center position .......... ................................................... ............ 28 11. shipping and package ........................... ................................................... ... 29 11.1 shipping label format......................... ................................................... ....................... 29 11.2. carton package............................... ................................................... ........................... 30 11.3 shipping package of palletizing sequence ...... ................................................... ............ 30 12. appendix: edid description..................... ................................................... . 31 www..net
au optronics corporation product specification document version 0.4 3/35 record of revision version and date page old description new description remark 0.1 2006/11/10 all first edition 0.2 2006/12/13 30 add shipping label format 0.2 2006/12/13 32 add edid data 0.3 2007/4/13 6 white luminance (iccfl=6.0ma) white luminance (iccfl=7.5ma) 0.4 2007/5/8 5~29 add specifications www..net
au optronics corporation product specification document version 0.4 4/35 1. handling precautions 1) since front polarizer is easily damaged, pay att ention not to scratch it. 2) be sure to turn off power supply when inserting or disconnecting from input connector. 3) wipe off water drop immediately. long contact wi th water may cause discoloration or spots. 4) when the panel surface is soiled, wipe it with a bsorbent cotton or other soft cloth. 5) since the panel is made of glass, it may break o r crack if dropped or bumped on hard surface. 6) since cmos lsi is used in this module, take care of static electricity and insure human earth when handling. 7) do not open nor modify the module assembly. 8) do not press the reflector sheet at the back of the module to any directions. 9) in case if a module has to be put back into the packing container slot after once it was taken out from the container, do not press the cent er of the ccfl reflector edge. instead, press at the far ends of the cfl reflector edge softly. otherwise the tft module may be damaged. 10) at the insertion or removal of the signal inter face connector, be sure not to rotate nor tilt the interface connector of the tft module. 11) after installation of the tft module into an en closure (notebook pc bezel, for example), do not twist nor bend the tft module even momentary. at designing the enclosure, it should be taken into consideration th at no bending/twisting forces are applied to the tft module from outside. otherwise the tft module may be damaged. 12) cold cathode fluorescent lamp in lcd contains a small amount of mercury. please follow local ordinances or regulations for disposal. 13) small amount of materials having no flammabilit y grade is used in the lcd module. the lcd module should be supplied by power complied wit h requirements of limited power source(, iec60950 or ul1950), or be applied exempti on. 14) the lcd module is designed so that the ccfl in it is supplied by limited current circuit(iec60950 or ul1950). do not connect the ccf l in hazardous voltage circuit. 2. general description b201sw01 v0 is a color active matrix liquid crystal display composed of a tft lcd panel, a driver circuit, and backlight system. the screen fo rmat is intended to support the wsxga+ (1680(h) x 1050(v)) screen and 16.7m colors (rgb 6- bits data driver with frame rate control). all input signals are lvds interface compatible. inverter of backlight is not included. www..net
au optronics corporation product specification document version 0.4 5/35 b201sw01 v0 is designed for a display unit of noteb ook style personal computer and industrial machine. 2.1 general specification the following items are characteristics summary on the table at 25 condition: items unit specifications screen diagonal [mm] 511.1 (20.1w?) active area [mm] 433.4 x 270.9 pixels h x v 1680x3(rgb) x 1050 pixel pitch [mm] 0.258x0.258 pixel arrangement r.g.b. vertical stripe display mode normally white white luminance (i ccfl =7.5ma) note: i ccfl is lamp current [cd/m 2 ] 300 typ. (5 points average) 255 min. (5 points average) ( note1 ) luminance uniformity 1.25 typ. (5 points) contrast ratio 1000 typ 800 min. optical rise time/fall time [msec] max 8/typ 5 nominal input voltage vdd [volt] +5.0 typ. power consumption [watt] 18.0 typ.( without inverte r) weight [grams] 1250 typ. 1310 max. physical size [mm] 453.5 typ. x 296.5 typ. x 8.6 max electrical interface 2-channel lvds surface treatment glare, hardness 3h, reflectance <=4.5% support color 16.7m colors temperature range operating storage (non-operating) [ o c] [ o c] 0 to +50 -20 to +60 rohs compliance rohs compliance www..net
au optronics corporation product specification document version 0.4 6/35 2.2 optical characteristics the optical characteristics are measured under stab le conditions at 25 (room temperature) : item unit conditions min. typ. max. note white luminance i ccfl =7.5ma [cd/m 2 ] 5 points average 255 300 - 1, 4, 5. [degree] [degree] horizontal (right) cr = 10 (left) 60 60 80 80 - - viewing angle [degree] [degree] vertical (upper) cr = 10 (lower) 60 60 80 75 - - 8 luminance uniformity 5 points 1.25 1.35 1 luminance uniformity 13 points 1.67 2.00 2 cr: contrast ratio 800 1000 - 6 cross talk % 4 7 [msec] rising - 3.8 5.7 [msec] falling - 1.2 2.3 response time [msec] rising + falling 5.0 8.0 8 red x 0.619 0.649 0.679 red y 0.308 0.338 0.368 green x 0.259 0.289 0.319 green y 0.579 0.609 0.639 blue x 0.116 0.146 0.176 blue y 0.040 0.070 0.100 white x 0.283 0.313 0.343 color / chromaticity coordinates (cie 1931) white y 0.299 0.329 0.359 2,8 www..net
au optronics corporation product specification document version 0.4 7/35 note 1: 5 points position (display area : 433.4mm x 270.9mm) 1 2 3 4 5 h /4 h /4 h /4 h /4 h w w /4 w /4 w /4 w /4 note 2: 13 points position w /4 w w /4 h h /4 h /4 h /4 h /4 7 9 1 0 w /4 1 8 w /4 1 0 1 0 1 0 1 0 2 3 1 3 1 2 4 5 6 1 1 note 3: the luminance uniformity of 5 and 13 point s is defined by dividing the maximum luminance valu es by the minimum test point luminance note 4: measurement method w13 = maximum brightnes s of thirteen points minimum brightness of thirteen points maximum brightness of five points w5 = minimum brightness of five points www..net
au optronics corporation product specification document version 0.4 8/35 the lcd module should be stabilized at given temper ature for 30 minutes to avoid abrupt temperature ch ange during measuring. in order to stabilize the luminan ce, the measurement should be executed after lighti ng backlight for 30 minutes in a stable, windless and dark room. note 5 definition of average luminance of white (y l ): measure the luminance of gray level 63 at 5 points y l = [l (1)+ l (2)+ l (3)+ l (4)+ l (5)] / 5 l (x) is corresponding to the luminance of the poin t x at figure in note (1). note 6 definition of contrast ratio: contrast ratio is calculated with the following for mula. note 7 definition of cross talk (ct) ct = | y b ? y a | / y a 100 (%) where y a = luminance of measured location without gray level 0 pattern (cd/m 2 ) center of the screen tft - lcd module 50 cm photo detector lcd panel field=2 contrast ratio (cr)= brightness on the ?white? state brightness on the ?bl ack? state www..net
au optronics corporation product specification document version 0.4 9/35 y b = luminance of measured location with gray level 0 pattern (cd/m 2 ) note 8: definition of response time: the output signals of bm-7 or equivalent are measur ed when the input signals are changed from ?black? to ?white? (falling time) and from ?white? to ?black? (rising time), respectively. the response time inte rval between the 10% and 90% of amplitudes. refer to figure as below . s i g n a l ( r e l a t i v e v a l u e ) "black" tr tf "white" "white" 0% 10% 90% 100% www..net
au optronics corporation product specification document version 0.4 10/35 note 8. definition of viewing angle viewing angle is the measurement of contrast ratio 10, at the screen center, over a 180 horizontal an d R 180 vertical range (off-normal viewing angles). th e 180 viewing angle range is broken down as follow s; 90 ( ) horizontal left and right and 90 ( ) vertical, high (up) and low (down). the measureme nt direction is typically perpendicular to the display surface with the scree n rotated about its center to develop the desired measurement viewing angle. www..net
au optronics corporation product specification document version 0.4 11/35 3. functional block diagram the following diagram shows the functional block of the 20.1wsxga+ tft/lcd module: tft array/cell vdd lcd controller lcd drive board backlight unit 1680(r/g/b) x 3 x 1050 gnd dc-dc converter ref circuit y-driver x-driver r o in0 roin1 roin2 roin3 roclkin rein0 rein1 rein2 rein3 r e clkin (10 pairs lvds) jae fi-nxb40sl-hf10 mating housing fi-nx40ch jst bhsr-02vs-1 mating type sm02b-bhss-1-tb lamp connector( 2 pin x2 ) l cd connector( 40 pin) www..net
au optronics corporation product specification document version 0.4 12/35 4. absolute maximum ratings absolute maximum ratings of the module is as follow ing: 4.1 absolute ratings of tft lcd module item symbol min max unit conditions logic/lcd drive voltage vin - 7 [volt] note 1,2 4.2 absolute ratings of backlight unit item symbol min max unit conditions ccfl current iccfl 7.0 8.0 [ma] rms note 1,2 4.3 absolute ratings of environment item symbol min max unit conditions operating temperature top 0 +50 [ o c] note 3 operation humidity hop 5 95 [%rh] note 3 storage temperature tst -20 +60 [ o c] note 3 storage humidity hst 5 95 [%rh] note 3 note 1: at ta (25 ) note 2: permanent damage to the device may occur if exceed maximum values note 3: for quality performance, please refer to au o iis(incoming inspection standard). twb=39c operating range storage range www..net
au optronics corporation product specification document version 0.4 13/35 5. electrical characteristics 5.1 tft lcd module 5.1.1 power specification input power specifications are as follows; symble parameter min typ max units note vdd logic/lcd drive voltage 4.5 5.0 5.5 [volt] pdd vdd power 6 [watt] note 1 idd idd current 1100 1400 [ma] note 1 i rush inrush current 8000 [ma] note 2 vddrp allowable logic/lcd drive ripple voltage 500 [mv] p-p note 1 : maximum measurement condition black pattern note 2 measure condition 90% 10% vin rising time 0v 5.0v 0.5ms www..net
au optronics corporation product specification document version 0.4 14/35 5.1.2 signal electrical characteristics input signals shall be low or high-impedance state when vdd is off. it is recommended to refer the specifications of th c63lvdf84a(thine electronics inc.) in detail. signal electrical characteristics are as follows; parameter condition min max unit vth differential input high threshold (vcm=+1.2v) 100 [mv] vtl differential input low threshold (vcm=+1.2v) -100 [mv] vcm differential input common mode voltage 1.125 1.375 [v] note: lvds signal waveform vth vtl vcm vss www..net
au optronics corporation product specification document version 0.4 15/35 5.2 backlight unit parameter guideline for ccfl inverter parameter min typ max units condition white luminance 5 points average 255 300 - [cd/m 2 ] (ta=25 ) ccfl current(i ccfl ) 7.0 7.5 8.0 [ma] rms (ta=25 ) note 2 ccfl frequency(f ccfl ) 40 60 80 [khz] (ta=25 ) note 3,4 ccfl ignition voltage(vs) 1550 [volt] rms (ta= 0 ) note 5 ccfl ignition voltage(vs) 1250 [volt] rms (ta= 25 ) note 5 ccfl voltage (reference) (v ccfl ) 750 [volt] rms (ta=25 ) note 6 ccfl power consumption (p ccfl ) - 11.3 [watt] (ta=25 ) note 6 note 1: typ are auo recommended design points. *1 all of characteristics listed are measured under the condition using the auo test inverter. *2 in case of using an inverter other than listed, it is recommended to check the inverter carefully. sometimes, interfering noise stripes appear on the screen, and substandard luminance or flicker at low power may happen. *3 in designing an inverter, it is suggested to che ck safety circuit very carefully. impedance of ccfl , for instance, becomes more than 1 [m ohm] when ccfl is damaged. *4 generally, ccfl has some amount of delay time af ter applying kick-off voltage. it is recommended to keep on applying kick-off voltage for 1 [sec] until disc harge. *5 ccfl discharge frequency must be carefully chose n so as not to produce interfering noise stripes on the screen. *6 reducing ccfl current increases ccfl discharge v oltage and generally increases ccfl discharge frequency. so all the parameters of an inverter sho uld be carefully designed so as not to produce too much leakage current from high-voltage output of the inv erter. note 2: it should be employed the inverter which ha s ?duty dimming?, if iccfl is less than 7ma. note 3: ccfl discharge frequency should be carefull y determined to avoid interference between inverter and tft lcd. www..net
au optronics corporation product specification document version 0.4 16/35 note 4: the frequency range will not affect to lamp life and reliability characteristics. note 5: ccfl inverter should be able to give out a power that has a generating capacity of over 1,280 voltage. lamp units need 1,250 voltage minimum for ignition. note 6: calculator value for reference (2lampxi ccfl v ccfl =p ccfl ) note 7: requirements for a system inverter design, which is intended to have a better display performa nce, a better power efficiency and a more reliable lamp, are foll owing. it shall help increase the lamp lifetime and reduce leakage current. a. the asymmetry rate of the inverter waveform shou ld be less than 10%. b. the distortion rate of the waveform should be wi thin 2 10%. * inverter output waveform had better be more simil ar to ideal sine wave. www..net
au optronics corporation product specification document version 0.4 17/35 6. signal characteristic 6.1 pixel format image following figure shows the relationship of the inpu t signals and lcd pixel format. r g b r g b r g b r g b r g b r g b r g b r g b 1 2 1679 1680 1st line 1050th line www..net
au optronics corporation product specification document version 0.4 18/35 6.2 the input data format www..net
au optronics corporation product specification document version 0.4 19/35 6.3 signal description/pin assignment lvds is a differential signal technology for lcd in terface and high speed data transfer device. pin# signal name description 1 gnd ground 2 gnd ground 3 avdd analog power supply 4 avdd analog power supply 5 avdd analog power supply 6 dvdd digital power supply 7 dvdd digital power supply 8 ddc_scl two wire serial interface clock 9 ddc_sda two wire serial interface data 10 rxino0- - lvds differential data input, chan 0-o dd 11 rxino0+ + lvds differential data input, chan 0-o dd 12 hgnd ground 13 rxino1- - lvds differential data input, chan 1-o dd 14 rxino1+ + lvds differential data input, chan 1-o dd 15 hgnd ground 16 rxino2- - lvds differential data input, chan 2-o dd 17 rxino2+ + lvds differential data input, chan 2-o dd 18 hgnd ground 19 rxclko- - lvds differential clock input (odd) 20 rxclko+ + lvds differential clock input (odd) 21 hgnd ground 22 rxino3- - lvds differential data input, chan 3-o dd 23 rxino3+ + lvds differential data input, chan 3-o dd 24 hgnd ground 25 rxine0- - lvds differential data input, chan 0-e ven 26 rxine0+ + lvds differential data input, chan 0-e ven 27 hgnd ground 28 rxine1- - lvds differential data input, chan 1-e ven 29 rxine1+ + lvds differential data input, chan 1-e ven 30 hgnd ground 31 rxine2- - lvds differential data input, chan 2-e ven 32 rxine2+ + lvds differential data input, chan 2-e ven 33 hgnd ground 34 rxclke- - lvds differential clock input (even) www..net
au optronics corporation product specification document version 0.4 20/35 35 rxclke+ + lvds differential clock input (even) 36 hgnd ground 37 rxine3- - lvds differential data input, chan 3-e ven 38 rxine3+ + lvds differential data input, chan 3-e ven 39 hgnd ground 40 nc reserved www..net
au optronics corporation product specification document version 0.4 21/35 6.4 interface timing 6.4.1 timing characteristics basically, interface timings should match the 1680x 1050 /60hz manufacturing guide line timing. parameter symbol min. typ. max. unit frame rate - - 60 - hz clock frequency 1/ t clock tbd 72.1 85 mhz period t v 1058 1066 2048 active t vd 1050 1050 1050 vertical section blanking t vb 8 16 998 t line period t h 880 1128 2048 active t hd 840 840 840 horizontal section blanking t hb 40 288 1208 t clock note : de mode only www..net
au optronics corporation product specification document version 0.4 22/35 6.4.2 timing diagram dotclk de t h t hb t hd de t v t vb t vd input timing definition ( de mode) t clock input data pixel 1 pixel 2 pixel 3 pixel n-1 pixel n invaild data invaild data pixel 1 www..net
au optronics corporation product specification document version 0.4 23/35 6.5 power on/off sequence vdd power and lamp on/off sequence is as follows. i nterface signals are also shown in the chart. signals from any system shall be hi-z state or low level when vdd is off. power sequence timing value parameter min. typ. max. units t1 0.5 - 10 (ms) t2 0 - 50 (ms) t3 0 - 50 (ms) t4 400 - - (ms) t5 200 - - (ms) t6 200 - - (ms) t7 0 - 10 (ms) t4 t3 t2 t5 valid data t1 10% 90% 10% 90% t6 t 7 power supply vdd lvds interface backlight on www..net
au optronics corporation product specification document version 0.4 24/35 7. connector description physical interface is described as for the connecto r on module. these connectors are capable of accommodating the f ollowing signals and will be following components. 7.1 tft lcd module connector name / designation for signal connector manufacturer jae or compatible type / part number jae, fi-nxb40sl-hf10 or compatib le mating housing/part number fi-nx40ch or compatible 7.2 backlight unit physical interface is described as for the connecto r on module. these connectors are capable of accommodating the f ollowing signals and will be following components. connector name / designation for lamp connector manufacturer jst type / part number bhsr-02vs-1 mating type / part number sm02b-bhss-1-tb 7.3 signal for lamp connector pin # cable color signal name 1 red lamp high voltage 2 white lamp low voltage 3 blue lamp high voltage 4 black lamp low voltage www..net
au optronics corporation product specification document version 0.4 25/35 8. vibration and shock test 8.1 vibration test test spec: test method: non-operation acceleration: 1.5grms frequency: 10~500hz sweep: 30min/axis 8.2 shock test spec: test spec: test method: non-operation acceleration: 160g active time: 2ms pulse: 1time/axis www..net
au optronics corporation product specification document version 0.4 26/35 9. reliability items required condition note temperature humidity bias 40 /90%,300hr high temperature operation 50 /dry,300hr low temperature operation 0 ,300hr on/off test 25 ,150hrs(on/10 sec. off/10sec., 10,000 cycles) hot storage 60 /35% rh ,250 hours cold storage -20 /50% rh ,250 hours thermal shock test -20 /3 0 min ,60 /30 min 100cycles hot start test 50 /1 hr min. power on/off per 5 minutes, 5 times cold start test 0 /1 hr min. power on/off per 5 minutes, 5 times shock test (non-operating) 160g/2ms, 1time/axis vibration test (non-operating) 1.5.grms, 10~500hz , 30min/axis esd contact : 8kv/ operation air : 15kv / operation note 1 room temperature test 25 , 2000hours, operating with loop pattern note1: according to en61000-4-2 , esd class b: some performance degradation allowed. no data lost . self-recoverable. no hardware failures. note2: ccfl life time: 10,000 hours minimum und er normal module usage. note3: mtbf (excluding the ccfl): 30,000 hours with a confidence level 90% www..net
document version 0.4 27/35 10. mechanical characteristics 10.1 lcm outline dimension www..net
document version 0.4 28/35 10.2 screw hole depth and center position screw hole minimum depth, from side surface =2.5mm (see drawing) screw hole center location, from front surface =4. 60.3 mm (see drawing) screw torque: maximum 2.5 kgf-cm www..net
document version 0.4 29/35 11. shipping and package 11.1 shipping label format www..net
document version 0.4 30/35 11.2. carton package 11.3 shipping package of palletizing sequence top cardboard wooden pallet bottom cardboard corner angle stretch film pe band note : limit of box palletizing = max 3 layers(ship and stock conditions) www..net
document version 0.4 31/35 12. appendix: edid description address address address address function function function function value value value value value value value value value value value value notes notes notes notes hex hex hex hex hex hex hex hex bin binbin bin dec dec dec dec 00 0000 00 header 00 0000 00 00000000 0 01 0101 01 ff ffff ff 11111111 255 02 0202 02 ff ffff ff 11111111 255 03 0303 03 ff ffff ff 11111111 255 04 0404 04 ff ffff ff 11111111 255 05 0505 05 ff ffff ff 11111111 255 06 0606 06 ff ffff ff 11111111 255 07 0707 07 00 0000 00 00000000 0 08 0808 08 eisa manuf. code lsb 06 0606 06 00000110 6 ascii data string:b201sw01 09 0909 09 compressed ascii af afaf af 10101111 175 auo 0a 0a0a 0a product code ab abab ab 10101011 171 b201sw 0b 0b0b 0b hex, lsb first 10 1010 10 00010000 16 01 v0 0c 0c0c 0c 32-bit ser # 00 0000 00 00000000 0 0 0d 0d0d 0d 00 0000 00 00000000 0 0 0e 0e0e 0e 00 0000 00 00000000 0 0 0f 0f0f 0f 00 0000 00 00000000 0 0 10 1010 10 week of manufacture 01 0101 01 00000001 1 week 1 11 1111 11 year of manufacture 11 1111 11 00010001 17 year(2007-1990=17) 12 1212 12 edid structure ver. 01 0101 01 00000001 1 13 1313 13 edid revision # 03 0303 03 00000011 3 14 1414 14 video input definition 80 8080 80 10000000 128 digital input 15 1515 15 max h image size 2b 2b2b 2b 00101011 43 33.00cm 16 1616 16 max v image size 1b 1b1b 1b 00011011 27 19.90cm 17 1717 17 display gamma 78 7878 78 01111000 120 gamma 2.2 18 1818 18 feature support 0a 0a0a 0a 00001010 10 no dpms,active off,rgb color 19 1919 19 red/green low bits 60 6060 60 01100000 96 1a 1a1a 1a blue/white low bits 85 8585 85 10000101 133 1b 1b1b 1b red x/ high bits a6 a6a6 a6 10100110 166 rx=0.649 1c 1c1c 1c red y 56 5656 56 01010110 86 ry=0.338 1d 1d1d 1d green x 4a 4a4a 4a 01001010 74 gx=0.289 1e 1e1e 1e green y 9c 9c9c 9c 10011100 156 gy=0.609 1f 1f1f 1f blue x 25 2525 25 00100101 37 bx=0.146 20 2020 20 blue y 12 1212 12 00010010 18 by=0.070 21 2121 21 white x 50 5050 50 01010000 80 wx=0.313 22 2222 22 white y 54 5454 54 01010100 84 xy=0.329 23 2323 23 established timing 1 00 0000 00 00000000 0 unused 24 2424 24 established timing 2 00 0000 00 00000000 0 25 2525 25 manufacturer's timing 00 0000 00 00000000 0 26 2626 26 standard timing #1 01 0101 01 00000001 1 unused 27 2727 27 01 0101 01 00000001 1 www..net
document version 0.4 32/35 28 2828 28 standard timing #2 01 0101 01 00000001 1 29 2929 29 01 0101 01 00000001 1 2a 2a2a 2a standard timing #3 01 0101 01 00000001 1 2b 2b2b 2b 01 0101 01 00000001 1 2c 2c2c 2c standard timing #4 0 00 01 11 1 00000001 1 2d 2d2d 2d 01 0101 01 00000001 1 2e 2e2e 2e standard timing #5 01 0101 01 00000001 1 2f 2f2f 2f 01 0101 01 00000001 1 30 3030 30 standard timing #6 01 0101 01 00000001 1 31 3131 31 01 0101 01 00000001 1 32 3232 32 standard timing #7 01 0101 01 00000001 1 33 3333 33 01 0101 01 00000001 1 34 3434 34 standard timing #8 01 0101 01 00000001 1 35 3535 35 01 0101 01 00000001 1 36 3636 36 pixel clock/10,000 (lsb) 5e 5e5e 5e 01011110 94 timing descriptor #1 37 3737 37 pixel clock/10,000 (msb) 38 3838 38 00111000 56 1680x1050 @60_mode:pixel clock=72.10mhz 38 3838 38 horiz. active pixels(lower 8 bits) 90 9090 90 10010000 144 horiz active=1680 pixels 3 33 39 99 9 horiz.blanking (lower 8 bits) 40 4040 40 01000000 64 horiz blanking=576 pixels 3a 3a3a 3a horiz. active pixels:horiz. blanking (upper4:4 bits) 62 6262 62 01100010 98 3b 3b3b 3b 1a 1a1a 1a 00011010 26 vertcal active=1050 lines 3c 3c3c 3c 10 1010 10 00010000 16 vertical blanking=16 lines 3d 3d3d 3d vert. active pixels:vert. blanking (upper4:4 bits) 40 4040 40 01000000 64 3e 3e3e 3e 40 4040 40 01000000 64 horiz sync. offset=64 pixels 3f 3f3f 3f c0 c0c0 c0 11000000 192 horiz sync. pulse width=192 pixels 40 4040 40 vert. sync. offset=xx lines, sync width=xx lines 13 1313 13 00010011 19 verti sync. offset=1 lines,sync width=3 lines 41 4141 41 horz. ver. sync/width (upper 2 bits) 00 0000 00 00000000 0 42 4242 42 hori. image size (lower 8 bits) b1 b1b1 b1 10110001 177 hori image size= 433 mm 43 4343 43 vert. image size (lower 8 bits) 0f 0f0f 0f 00001111 15 verti image size = 271mm 44 4444 44 hori. image size : vert. image size (upper 4 bits) 11 1111 11 00010001 17 45 4545 45 00 0000 00 00000000 0 horizontal border = 0 46 4646 46 00 0000 00 00000000 0 vertical border = 0 47 4747 47 18 1818 18 00011000 24 48 4848 48 detailed timing/monitor 00 0000 00 00000000 0 ascii data string:b201sw01 49 4949 49 descriptor #2 00 0000 00 00000000 0 4a 4a4a 4a 00 0000 00 00000000 0 4b 4b4b 4b 0f 0f0f 0f 00001111 15 4c 4c4c 4c 00 00000000 0 4d 4d4d 4d 00 00000000 0 4e 4e4e 4e 00 00000000 0 4f 4f4f 4f 00 00000000 0 50 5050 50 00 00000000 0 51 5151 51 00 00000000 0 www..net
document version 0.4 33/35 52 5252 52 00 00000000 0 53 5353 53 00 00000000 0 54 5454 54 00 00000000 0 55 5555 55 00 00000000 0 56 5656 56 00 00000000 0 57 5757 57 00 00000000 0 58 5858 58 00 00000000 0 59 5959 59 20 2020 20 00100000 32 5a 5a5a 5a detailed timing/monitor 00 0000 00 00000000 0 ascii data string:b201sw01 5b 5b5b 5b descriptor #3 00 0000 00 00000000 0 5c 5c5c 5c 00 0000 00 00000000 0 5d 5d5d 5d fe fefe fe 11111110 254 5e 5e5e 5e 00 00000000 0 5f 5f5f 5f 41 4141 41 01000001 65 a 60 6060 60 55 5555 55 01010101 85 u 61 6161 61 4f 4f4f 4f 01001111 79 o 62 6262 62 0a 0a0a 0a 00001010 10 63 6363 63 20 2020 20 00100000 32 64 6464 64 20 2020 20 00100000 32 65 6565 65 20 2020 20 00100000 32 66 6666 66 20 2020 20 00100000 32 67 6767 67 20 2020 20 00100000 32 68 6868 68 20 2020 20 00100000 32 69 6969 69 20 2020 20 00100000 32 6a 6a6a 6a 20 2020 20 00100000 32 6b 6b6b 6b 20 2020 20 00100000 32 6c 6c6c 6c detailed timing/monitor 00 0000 00 00000000 0 monitor name: color lcd 6d 6d6d 6d descriptor #4 00 0000 00 00000000 0 6e 6e6e 6e 00 0000 00 00000000 0 6f 6f6f 6f fe fefe fe 11111110 254 70 7070 70 00 0000 00 00000000 0 71 7171 71 42 4242 42 01000010 66 b 72 7272 72 3 33 32 22 2 00110010 50 2 73 7373 73 30 3030 30 00110000 48 0 74 7474 74 31 3131 31 00110001 49 1 75 7575 75 53 5353 53 01010011 83 s 76 7676 76 57 5757 57 01010111 87 w 77 7777 77 30 3030 30 00110000 48 0 78 7878 78 31 3131 31 00110001 49 1 79 7979 79 20 2020 20 00100000 32 7a 7a7a 7a 56 5656 56 01010110 86 v 7b 7b7b 7b 30 3030 30 00110000 48 0 7c 7c7c 7c 20 2020 20 00100000 32 7d 7d7d 7d 0a 0a0a 0a 00001010 10 www..net
document version 0.4 34/35 7e 7e7e 7e extension flag 00 0000 00 00000000 0 7f 7f7f 7f checksum 6e 6e6e 6e 01101110 110 www..net
document version 0.4 35/35 www..net

▲Up To Search▲

Price & Availability of B201SW01V0

	To Download B201SW01V0 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .