original creation date: 06/23/95 last update date: 04/08/02 last major revision date: 06/23/95 mnlm105-x rev 0c0 microcircuit data sheet voltage regulator general description the lm105 positive voltage regulator is similar to the lm100, except that an extra gain stage has been added for improved regulation. a redesign of the biasing circuitry removes any minimum load current requirement and at the same time reduces standby current drain, permitting higher voltage operation. it is a direct, plug-in replacement for the lm100 in both linear and switching regulator circuits with output voltages greater than 4.5v. important characteristics of the circuit is: - output voltage adjustable from 4.5v to 40v - output currents in excess of 10a possible by adding external transistors - load regulation better than 0.1%, full load with current limiting - dc line regulation guaranteed at 0.30%/v - ripple rejection on 0.01%/v as with the lm100, it also features fast response to both load and line transients, freedom from oscillations with varying resistive and reactive loads and the ability to start reliably on any load within rating. the circuit is built on a single silicon chip. the lm105 is specified for operation for -55 c < ta < +125 c. ns part numbers LH105H-MLS lm105h/883 industry part number lm105 prime die lm105 processing mil-std-883, method 5004 quality conformance inspection mil-std-883, method 5005 subgrp description temp ( c) o 1 static tests at +25 2 static tests at +125 3 static tests at -55 4 dynamic tests at +25 5 dynamic tests at +125 6 dynamic tests at -55 7 functional tests at +25 8a functional tests at +125 8b functional tests at -55 9 switching tests at +25 10 switching tests at +125 11 switching tests at -55 1
microcircuit data sheet mnlm105-x rev 0c0 (absolute maximum ratings) (note 1) input voltage 50v input-output differential 40v power dissipation 800 mw operating temperature range -55 c < ta < +125 c storage temperature range -65 c < ta < +150 c lead temperature 300 c (soldering, 10 seconds) maximum junction temperature 150 c thermal resistance thetaja 165 c/w (still air) 96 c/w (500lf/min air flow) 43 c/w thetajc esd tolerance 1500v note 1: absolute maximum ratings indicate limits beyond which damage to the device may occur. operating ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. for guaranteed specifications and test conditions, see the electrical characteristics. the guaranteed specifications apply only for the test conditions listed. some performance characteristics may degrade when the device is not operated under the listed test conditions. 2
mnlm105-x rev 0c0 microcircuit data sheet electrical characteristics dc parameters (the following conditions apply to all the following parameters, unless otherwise specified.) dc: vout = 4.5v, rsc = 0 ohms. symbol parameter conditions notes pin- name min max unit sub- groups r23 pin 2 to pin 3 resistance v23 = 0.25v 0.2 1.2 kohms 1 0.14 2.5 kohms 2, 3 iq quiescent current vin = 50v -0.1 -2 ma 1, 2 -0.1 -3 ma 3 vref reference voltage vin = 8.4v (feedback sense voltage) 1.63 1.81 v 1, 2, 3 vrload load regulation vin = 8.4v, 0.7ma < il < 13ma 0.05 % 1 0.1 % 2, 3 vin = 50v, 0.7ma < il < 13ma, vout = 40.5v 0.05 % 1 0.1 % 2, 3 vin = 43v, 13ma > il > 0.7ma, vout = 40.5v 0.05 % 1 0.1 % 2, 3 vrline line regulation il = 13ma, 8.4v < vin < 44.5v 3 1 % 1, 2, 3 il = 0.7ma, 8.4v < vin < 44.5v 3 1 % 1, 2, 3 il = 0.7ma, 43v < vin < 50v, vout = 40.5v 4 0.2 % 1, 2, 3 il = 13ma, 50v < vin < 43v, vout = 40.5v 4 0.2 % 1, 2, 3 ibias input bias current vin = 50v 6 ua 1, 2 10.5 ua 3 vsense current limit sense voltage vin = 20v, vout = gnd, rsc = 10 ohms 225 375 mv 1 70 305 mv 2 195 510 mv 3 vin input voltage range 1 8.5 50 v 1, 2, 3 vout output voltage range 1 4.5 40 v 1, 2, 3 vdiff output-input voltage differential 1 3 30 v 1, 2, 3 ripple rejection vin = 25v, cref = 10uf, vout = 20v, f = 120hz, vin = 0.707vrms 2 1.4 mvrms 1 3
mnlm105-x rev 0c0 microcircuit data sheet electrical characteristics dc parameters: drift values (the following conditions apply to all the following parameters, unless otherwise specified.) dc: vout = 4.5v, rsc = 0 ohms. "deltas not required on b-level product. deltas required for s-level product as specified on internal processing instructions (ipi)." symbol parameter conditions notes pin- name min max unit sub- groups iq quiescent current vin = 50v -0.2 0.2 ma 1 vref reference voltage vin = 8.4v (feedback sense voltage) -0.02 0.02 v 1 ibias input bias current vin = 50v -1 1 ua 1 note 1: parameter guaranteed by line regulation. note 2: ripple rejection test may be done on ltx or bench use (sg)rpi-3-369. note 3: 1% = 0.03%/v. note 4: 0.2% = 0.03%/v. 4
microcircuit data sheet mnlm105-x rev 0c0 graphics and diagrams graphics# description 9797hrb 8ld .200 dia p.c. to-99 metal can(h) (b/i ckt) h08crf metal can (h), to-99, 8ld, .200 dia p.c. (p/p dwg) see attached graphics following this page. 5
microcircuit data sheet mnlm105-x rev 0c0 revision history rev ecn # rel date originator changes 0c0 m0003999 04/08/02 rose malone update mds: mnlm105-x, rev. 0b0 to mnlm105-x, rev. 0c0. added lm105h-mls to main table under ns part numbers section and updated absolute maximum ratings section adding thermal resistance limits. 6
|
