|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
rev. 0 information furnished by analog devices is believed to be accurate and reliable. however, no responsibility is assumed by analog devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. no license is granted by implication or otherwise under any patent or patent rights of analog devices. a ad7708/AD7718 one technology way, p.o. box 9106, norwood, ma 02062-9106, u.s.a. tel: 781/329-4700 www.analog.com fax: 781/326-8703 ? analog devices, inc., 2001 8-/10-channel, low voltage, low power, - adcs functional block diagram dvdd xtal1 xtal2 mux pos buf - adc * ain1 ain2 ain3 ain4 pga osc and pll serial interface and control logic dout din sclk cs rdy reset av d d i/o port av d d ad7708/AD7718 dgnd p2 p1 refin2(+)/ain9 refin1(+) refin2(?/ain10 refin1(? aincom ain5 ain6 ain7 ain8 agnd *ad7708 16-bit adc *AD7718 24-bit adc refin(+) refin(? neg buf features 8-/10-channel, high resolution - adcs ad7708 has 16-bit resolution AD7718 has 24-bit resolution factory-calibrated single conversion cycle setting programmable gain front end simultaneous 50 hz and 60 hz rejection vref select ? allows absolute and ratiometric measurement capability operation can be optimized for analog performance ( chop = 0) or channel throughput ( chop = 1) interface 3-wire serial spi tm , qspi tm , microwire tm , and dsp-compatible schmitt trigger on sclk power specified for single 3 v and 5 v operation normal: 1.28 ma typ @ 3 v power-down: 30 a (32 khz crystal running) on-chip functions rail-to-rail input buffer and pga 2-bit digital i/o port applications industrial process control instrumentation pressure transducers portable instrumentation smart transmitters spi and qspi are trademarks of motorola inc. microwire is a trademark of national semiconductor corp. vref select is a trademark of analog devices, inc. general description the ad7708/AD7718 are complete analog front-ends for low frequency measurement applications. the AD7718 contains a 24-bit - ? adc with pga and can be configured as 4/5 fully- differential input channels or 8/10 pseudo-differential input channels. two pins on the device are configurable as analog inputs or reference inputs. the ad7708 is a 16-bit version of the AD7718. input signal ranges from 20 mv to 2.56 v can be directly converted using these adcs. signals can be converted directly from a transducer without the need for signal conditioning. the device operates from a 32 khz crystal with an on-board pll generating the required internal operating frequency. the output data rate from the part is software programmable. the peak-to- peak resolution from the part varies with the programmed gain and output data rate. the part operates from a single 3 v or 5 v supply. when operating from 3 v supplies, the power dissipation for the part is 3.84 mw typ. both parts are pin-for-pin compatible allowing an upgradable path from 16 to 24 bits without the need for hardware modifica- tions. the ad7708/AD7718 are housed in 28-lead soic and tssop packages.
rev. 0 C2C ad7708/AD7718 features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 functional block diagram . . . . . . . . . . . . . . . . . 1 general description . . . . . . . . . . . . . . . . . . . . . . . . . 1 AD7718 specifications . . . . . . . . . . . . . . . . . . . . . . . . 3 ad7708 specifications . . . . . . . . . . . . . . . . . . . . . . . . 6 timing characteristics . . . . . . . . . . . . . . . . . . . . . 9 absolute maximum ratings . . . . . . . . . . . . . . . . 10 ordering guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 pin function descriptions . . . . . . . . . . . . . . . . . 12 pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . 13 adc circuit information . . . . . . . . . . . . . . . . . . . 15 signal chain overview (chop enabled, chop = 0) . . . 15 adc noise performance chop enabled ( chop = 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 signal chain overview (chop disabled chop = 1) . . . 19 adc noise performance chop disabled ( chop = 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 on-chip registers . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 communications register . . . . . . . . . . . . . . . . . . . . . . . . . . 25 status register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 mode register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 operating characteristics when addressing the mode and control registers . . . . . . . . . . . . . . . . . . . . . . . 28 adc control register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 filter register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 i/o control register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 adc data result register . . . . . . . . . . . . . . . . . . . . . . . . . . 30 unipolar mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 bipolar mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 adc offset calibration coefficient registers . . . . . . . . . . . 31 adc gain calibration coefficient register . . . . . . . . . . . . . 31 id register (id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 user nonprogrammable test registers . . . . . . . . . . . . . . . . 31 configuring the ad7708/AD7718 . . . . . . . . . . . . . . . . . . . . 32 digital interface . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 microcomputer/microprocessor interfacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 ad7708/AD7718 to 68hc11 interface . . . . . . . . . . . . . . . . 34 ad7708/AD7718-to-8051 interface . . . . . . . . . . . . . . . . . . 35 ad7708/AD7718-to-adsp-2103/adsp-2105 interface . . . 36 basic configuration . . . . . . . . . . . . . . . . . . . . . . . . 36 analog input channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 single-ended operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 chop mode of operation (chop = 0) . . . . . . . . . . . . . . . . 37 nonchop mode of operation (chop = 1) . . . . . . . . . . . . . 38 programmable gain amplifier . . . . . . . . . . . . . . . . . . . . . . . 38 bipolar/unipolar configuration . . . . . . . . . . . . . . . . . . . . . . 38 data output coding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 oscillator circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 reference input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 reset input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 power-down mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 grounding and layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 data acquisition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 programmable logic controllers . . . . . . . . . . . . . . . . . . . . . 41 converting single-ended inputs. . . . . . . . . . . . . . . . . . . . . 42 combined ratiometric and absolute value measurement system . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 optimizing throughput while maximizing 50 hz and 60 hz rejection in a multiplexed data acquisition system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 outline dimensions . . . . . . . . . . . . . . . . . . . . . . . . . 44 table of contents rev. 0 C3C ad7708/AD7718 parameter b grade unit test conditions AD7718 (chop disabled) output update rate 16.06 hz min chop = 1 1.365 khz max no missing codes 2 24 bits min resolution 13 bits p-p 20 mv range, sf = 69 18 bits p-p 2.56 v range, sf = 69 output noise and update rates see tables in adc description integral nonlinearity 10 ppm of fsr max 2 ppm typical offset error 3 table vii v typ offset error is in the order of the noise for the programmed gain and update rate following a calibration offset error drift vs. temp 4 200 nv/ c typ full-scale error 3 10 v typ gain drift vs. temp 4 0.5 ppm/ c typ negative full-scale error 0.003 % fsr max analog inputs differential input full-scale voltage 1.024 refin/gain v nom refin refers to both refin1 and refin2. refin = refin(+) Crefin(C) gain = 1 to 128 absolute ain voltage limits agnd + 100 mv v min ain1Cain10 and aincom with av dd C 100 mv v max negbuf = 1 absolute aincom voltage limits agnd C 30 mv v min negbuf = 0 av dd + 30 mv v max analog input current ain1Cain10 and aincom with negbuf = 1 dc input current 2 1 na max dc bias current drift 5pa/ c typ aincom input current negbuf = 0 dc input current 2 125 na/v typ 2.56 v range dc bias current drift 2 pa/v/ c typ normal-mode rejection 2 @ 50 hz 100 db min 50 hz 1 hz, sf word = 82 @ 60 hz 100 db min 60 hz 1 hz, sf word = 68 common-mode rejection @ dc 90 db min 100 db typ, analog input = 1 v, input range = 2.56 v 110 db typ on 20 mv range @ 50 hz 100 db typ 50 hz 1 hz, sf word = 82 @ 60 hz 100 db typ 60 hz 1 hz, sf word = 68 reference inputs (refin1 and refin2) refin(+) to refin(C) voltage 2.5 v nom refin refers to both refin1 and refin2 refin(+) to refin(C) range 2 1v min av dd v max refin common-mode range agnd C 30 mv v min av dd + 30 mv v max reference dc input current 0.5 a/v typ reference dc input current drift 0.1 na/v/ c typ normal-mode rejection 2 @ 50 hz 100 db min 50 hz 1 hz, sf word = 82 @ 60 hz 100 db min 60 hz 1 hz, sf word = 68 common-mode rejection input range = 2.56 v @ dc 100 db typ analog input = 1 v. input range = 2.56 v @ 50 hz 100 db typ @ 60 hz 100 db typ AD7718 specifications 1 (av dd = 2.7 v to 3.6 v or 4.75 v to 5.25 v, dv dd = 2.7 v to 3.6 v or 4.75 v to 5.25 v, refin(+) = 2.5 v; refin(? = agnd; agnd = dgnd = 0 v; xtal1/xtal2 = 32.768 khz crystal input buffer enabled. all specifications t min to t max unless otherwise noted.) rev. 0 C4C AD7718?pecifications 1 (av dd = 2.7 v to 3.6 v or 4.75 v to 5.25 v, dv dd = 2.7 v to 3.6 v or 4.75 v to 5.25 v, refin(+) = 2.5 v ; refin(? = agnd; agnd = dgnd = 0 v; xtal1/xtal2 = 32.768 khz crystal input buffer enabled. all specifications t min to t max unless otherwise noted.) parameter b grade unit test conditions AD7718 (chop enabled) output update rate 5.4 hz min chop = 0 105 hz max no missing codes 2 24 bits min 20 hz update rate resolution 13 bits p-p 20 mv range, 20 hz update rate 18 bits p-p 2.56 v range, 20 hz update rate output noise and update rates see tables in adc description integral nonlinearity 10 ppm of fsr max 2 ppm typical offset error 3 3 v typ offset error drift vs. temp 4 10 nv/ c typ full-scale error 3 10 v/ c typ gain drift vs. temp 4 0.5 ppm/ c typ analog inputs differential input full-scale voltage 1.024 refin/gain v nom refin refers to both refin1 and refin2. refin = refin(+) refin(C) gain = 1 to 128 range matching 2 v typ analog input = 18 mv absolute ain voltage limits agnd + 100 mv v min ain1Cain10 and aincom with av dd C 100 mv v max negbuf = 1 absolute aincom voltage limits agnd C 30 mv v min negbuf = 0 av dd + 30 mv v max analog input current ain1Cain10 and aincom with negbuf = 1 dc input current 2 1 na max dc input current drift 5 pa/ c typ aincom input current negbuf = 0 dc input current 2 125 na/v typ 2.56 v range dc bias current drift 2 pa/v/ c typ normal-mode rejection 2 @ 50 hz 100 db min 50 hz 1 hz, sf word = 82 @ 60 hz 100 db min 60 hz 1 hz, sf word = 68 common-mode rejection @ dc 90 db min 100 db typ, analog input = 1 v, input range = 2.56 v 110 db typ on 20 mv range @ 50 hz 2 100 db min 50 hz 1 hz, 20 hz update rate @ 60 hz 2 100 db min 60 hz 1 hz, 20 hz update rate reference inputs (refin1 and refin2) refin(+) to refin(C) voltage 2.5 v nom refin refers to both refin1 and refin2 refin(+) to refin(C) range 2 1v min av dd v max refin common-mode range agnd C 30 mv v min av dd + 30 mv v max reference dc input current 2 0.5 a/v typ reference dc input current drift 0.01 na/v/ c typ normal-mode rejection 2 @ 50 hz 100 db min 50 hz 1 hz, sf word = 82 @ 60 hz 100 db min 60 hz 1 hz, sf word = 68 common-mode rejection 2 input range = 2.56 v @ dc 110 db typ analog input = 1 v @ 50 hz 110 db typ 50 hz 1 hz, 20 hz update rate @ 60 hz 110 db typ 60 hz 1 hz, 20 hz update rate logic inputs 5 all inputs except sclk and xtal1 2 v inl , input low voltage 0.8 v max dv dd = 5 v v inl , input low voltage 0.4 v max dv dd = 3 v v inh , input high voltage 2.0 v min dv dd = 3 v or 5 v rev. 0 C5C ad7708/AD7718 parameter b grade unit test conditions logic inputs (continued) sclk only (schmitt-triggered input) 2 v t(+) 1.4/2 v min/v max dv dd = 5 v v t(C) 0.8/1.4 v min/v max dv dd = 5 v v t(+) C v t(C) 0.3/0.85 v min/v max dv dd = 5 v v t(+) 0.95/2 v min/v max dv dd = 3 v v t(C) 0.4/1.1 v min/v max dv dd = 3 v v t(+) Cv t(C) 0.3/0.85 v min/v max dv dd = 3 v xtal1 only 2 v inl , input low voltage 0.8 v max dv dd = 5 v v inh , input high voltage 3.5 v min dv dd = 5 v v inl , input low voltage 0.4 v max dv dd = 3 v v inh , input high voltage 2.5 v min dv dd = 3 v input currents 10 a max logic input = dv dd C70 a max logic input = dgnd, typical C40 a @ 5 v and C20 a at 3 v input capacitance 10 pf typ all digital inputs logic outputs (excluding xtal2) 5 v oh , output high voltage 2 dv dd C 0.6 v min dv dd = 3 v, i source = 100 a v ol , output low voltage 2 0.4 v max dv dd = 3 v, i sink = 100 a v oh , output high voltage 2 4v mindv dd = 5 v, i source = 200 a v ol , output low voltage 2 0.4 v max dv dd = 5 v, i sink = 1.6 ma floating state leakage current 10 a max floating state output capacitance 10 pf typ data output coding binary unipolar mode offset binary bipolar mode system calibration 2 full-scale calibration limit 1.05 fs v max zero-scale calibration limit C1.05 fs v min input span 0.8 fs v min 2.1 fs v max start-up time from power-on 300 ms typ from power-down mode 1 ms typ oscillator enabled 300 ms typ oscillator powered down power requirements power supply voltages av dd and dv dd can be operated independently of each other. av dd Cagnd 2.7/3.6 v min/max av dd = 3 v nom 4.75/5.25 v min/max av dd = 5 v nom dv dd Cdgnd 2.7/3.6 v min/max dv dd = 3 v nom 4.75/5.25 v min dv dd = 5 v nom di dd (normal mode) 0.55 ma max dv dd = 3 v, 0.43 ma typ 0.65 ma max dv dd = 5 v, 0.5 ma typ ai dd (normal mode) 1.1 ma max av dd = 3 v or 5 v, 0.85 ma typ di dd (power-down mode) 10 a max dv dd = 3 v, 32.768 khz osc. running 2 a max dv dd = 3 v, oscillator powered down 30 a max dv dd = 5 v, 32.768 khz osc. running 8 a max dv dd = 5 v, oscillator powered down ai dd (power-down mode) 1 a max av dd = 3 v or 5 v power supply rejection (psr) input range = 2.56 v, ain = 1 v chop disabled 70 db min 95 db typ chop enabled 100 db typ notes 1 temperature range is C40 c to +85 c. 2 not production tested, guaranteed by design and/or characterization data at release. 3 following a self-calibration this error will be in the order of the noise for the programmed gain and update selected. a system calibration will completely remove this error. 4 recalibration at any temperature will remove these errors. 5 i/o port logic levels are with respect to av dd and agnd. specifications are subject to change without notice. rev. 0 C6C ad7708/AD7718 ad7708 specifications 1 (av dd = 2.7 v to 3.6 v or 4.75 v to 5.25 v, dv dd = 2.7 v to 3.6 v or 4.75 v to 5.25 v, refin(+) = 2.5 v; refin(? = agnd; agnd = dgnd = 0 v; xtal1/xtal2 = 32.768 khz crystal input buffers enabled. all specification s t min to t max unless otherwise noted.) parameter b grade unit test conditions ad7708 (chop disabled) output update rate 16.06 hz min chop = 1 1.365 khz max no missing codes 2 16 bits min resolution 13 bits p-p 20 mv range, sf word = 69 16 bits p-p 2.56 v range, sf word = 69 output noise and update rates see tables in adc description integral nonlinearity 15 ppm of fsr max 2ppm typical offset error 3 0.65 lsb typ following a self-calibration offset error drift vs. temp 4 200 nv/ c typ full-scale error 3 0.75 lsb typ gain drift vs. temp 4 0.5 ppm/ c typ negative full-scale error 0.003 % fsr typ analog inputs differential input full-scale voltage 1.024 refin/gain v nom refin refers to both refin1 and refin2. refin = refin(+) C refin(C) gain = 1 to 128 absolute ain voltage limits agnd + 100 mv v min ain1Cain10 and aincom with av dd C 100 mv v max negbuf = 1 absolute aincom voltage limits agnd C 30 mv v min negbuf = 0 av dd + 30 mv v max analog input current ain1Cain10 and aincom with negbuf = 1 dc input current 2 1 na max dc bias current drift 5 pa/ c typ aincom input current negbuf = 0 dc input current 2 125 na/v typ 2.56 v range dc bias current drift 2 pa/v/ c typ normal-mode rejection 2 @ 50 hz 100 db min 50 hz 1 hz, sf word = 82 @ 60 hz 100 db min 60 hz 1 hz, sf word = 68 common-mode rejection @ dc 90 db min 100 db typ, analog input = 1 v, input range = 2.56 v 110 db typ on 20 mv range @ 50 hz 100 db typ 50 hz 1 hz, sf word = 82 @ 60 hz 100 db typ 60 hz 1 hz, sf word = 68 reference inputs (refin1 and refin2) refin(+) to refin(C) voltage 2.5 v nom refin refers to both refin1 and refin2 refin(+) to refin(C) range 2 1v min av dd v max refin common-mode range agnd C 30 mv v min av dd + 30 mv v max reference dc input current 0.5 a/v typ reference dc input current drift 0.1 na/v/ c typ normal-mode rejection 2 @ 50 hz 100 db min 50 hz 1 hz, sf word = 82 @ 60 hz 100 db min 60 hz 1 hz, sf word = 68 common-mode rejection input range = 2.56 v @ dc 100 db typ analog input = 1 v. input range = 2.56 v @ 50 hz 100 db typ @ 60 hz 100 db typ rev. 0 C7C ad7708/AD7718 parameter b grade unit test conditions ad7708 (chop enabled ) output update rate 5.4 hz min chop = 1 105 hz max 0.732 ms increments no missing codes 2 16 bits min 20 hz update rate resolution 13 bits p-p 20 mv range, 20 hz update rate 16 bits p-p 2.56 v range, 20 hz update rate output noise and update rates see tables in adc description integral nonlinearity 15 ppm of fsr max 2 ppm typical offset error 3 3 v typ calibration is accurate to 0.5 lsb offset error drift vs. temp 4 10 nv/ c typ full-scale error 3 0.75 lsb typ includes positive and negative errors gain drift vs. temp 4 0.5 ppm/ c typ analog inputs differential input full-scale voltage 1.024 refin/gain v nom refin refers to both refin1 and refin2. refin = refin(+) refin(C) gain = 1 to 128 range matching 2 v typ analog input = 18 mv absolute ain voltage limits agnd + 100 mv v min ain1Cain10 and aincom with av dd C 100 mv v max negbuf = 1 absolute aincom voltage limits agnd C 30 mv v min negbuf = 0 av dd + 30 mv v max analog input current ain1Cain10 and aincom with negbuf = 1 dc input current 2 1 na max dc input current drift 5 pa/ c typ aincom input current negbuf = 0 dc input current 2 125 na/v typ dc bias current drift 2 pa/v/ c typ normal-mode rejection 2 @ 50 hz 100 db min 50 hz 1 hz, sf word = 82 @ 60 hz 94 db min 60 hz 1 hz, sf word = 68 common-mode rejection @ dc 90 db min 100 db typ, analog input = 1 v, input range = 2.56 v 110 db typ on 20 mv range @ 50 hz 2 100 db min 50 hz 1 hz, 20 hz update rate @ 60 hz 2 100 db min 60 hz 1 hz, 20 hz update rate reference inputs (refin1 and refin2) refin(+) to refin(C) voltage 2.5 v nom refin refers to both refin1 and refin2 refin(+) to refin(C) range 2 1v min av dd v max refin common-mode range agnd C 30 mv v min av dd + 30 mv v max reference dc input current 2 0.5 a/v typ reference dc input current drift 0.01 na/v/ c typ normal-mode rejection 2 @ 50 hz 100 db min 50 hz 1 hz, sf word = 82 @ 60 hz 100 db min 60 hz 1 hz, sf word = 68 common-mode rejection input range = 2.56 v @ dc 110 db typ analog input = 1 v @ 50 hz 110 db typ 50 hz 1 hz, 20 hz update rate @ 60 hz 110 db typ 60 hz 1 hz, 20 hz update rate logic inputs 5 all inputs except sclk and xtal1 2 v inl , input low voltage 0.8 v max dv dd = 5 v 0.4 v max dv dd = 3 v v inh , input high voltage 2.0 v min dv dd = 3 v or 5 v rev. 0 C8C AD7718?pecifications 1 (av dd = 2.7 v to 3.6 v or 4.75 v to 5.25 v, dv dd = 2.7 v to 3.6 v or 4.75 v to 5.25 v, refin(+) = 2.5 v ; refin(? = agnd; agnd = dgnd = 0 v; xtal1/xtal2 = 32.768 khz crystal input buffer enabled. all specifications t min to t max unless otherwise noted.) ad7708 parameter b grade unit test conditions logic inputs (continued) sclk only (schmitt-triggered input) 2 v t(+) 1.4/2 v min/v max dv dd = 5 v v t(C) 0.8/1.4 v min/v max dv dd = 5 v v t(+) Cv t(C) 0.3/0.85 v min/v max dv dd = 5 v v t(+) 0.95/2 v min/v max dv dd = 3 v v t(C) 0.4/1.1 v min/v max dv dd = 3 v v t(+) Cv t(C) 0.3/0.85 v min/v max dv dd = 3 v xtal1 only 2 v inl , input low voltage 0.8 v max dv dd = 5 v v inh , input high voltage 3.5 v min dv dd = 5 v v inl , input low voltage 0.4 v max dv dd = 3 v v inh , input high voltage 2.5 v min dv dd = 3 v input currents 10 a max logic input = dv dd C70 a max logic input = dgnd, typical C40 a @ 5 v and C20 a at 3 v input capacitance 10 pf typ all digital inputs logic outputs (excluding xtal2) 5 v oh , output high voltage 2 dv dd C 0.6 v min dv dd = 3 v, i source = 100 a v ol , output low voltage 2 0.4 v max dv dd = 3 v, i sink = 100 a v oh , output high voltage 2 4v mindv dd = 5 v, i source = 200 a v ol , output low voltage 2 0.4 v max dv dd = 5 v, i sink = 1.6 ma floating state leakage current 10 a max floating state output capacitance 10 pf typ data output coding binary unipolar mode offset binary bipolar mode system calibration 2 full-scale calibration limit 1.05 fs v max zero-scale calibration limit C1.05 fs v min input span 0.8 fs v min 2.1 fs v max start-up time from power-on 300 ms typ from power-down mode 1 ms typ 300 ms typ oscillator powered down power requirements power supply voltages av dd and dv dd can be operated independently of each other. av dd Cagnd 2.7/3.6 v min/max av dd = 3 v nom 4.75/5.25 v min/max av dd = 5 v nom dv dd Cdgnd 2.7/3.6 v min/max dv dd = 3 v nom 4.75/5.25 v min dv dd = 5 v nom di dd (normal mode) 0.55 ma max dv dd = 3 v, 0.43 ma typ 0.65 ma dv dd = 5 v, 0.5 ma typ ai dd (normal mode) 1.1 ma av dd = 3 v or 5 v, 0.85 ma typ di dd (power-down mode) 10 a max dv dd = 3 v, 32.768 khz osc. running 2 a max dv dd = 3 v, oscillator powered down 30 a max dv dd = 5 v, 32.768 khz osc. running 8 a max dv dd = 5 v, oscillator powered down ai dd (power-down mode) 1 a max av dd = 3 v or 5 v power supply rejection (psr) input range = 2.56 v, ain = 1 v chop disabled 70 db min 95 db typ chop enabled 100 db typ notes 1 temperature range is C40 c to +85 c. 2 not production tested, guaranteed by design and/or characterization data at release. 3 following a self-calibration this error will be in the order of the noise for the programmed gain and update selected. a system calibration will completely remove this error. 4 recalibration at any temperature will remove these errors. 5 i/o port logic levels are with respect to av dd and agnd. specifications are subject to change without notice. rev. 0 ad7708/AD7718 C9C timing characteristics 1, 2 (av dd = 2.7 v to 3.6 v or av dd = 5 v 5%; dv dd = 2.7 v to 3.6 v or dv dd = 5 v 5%; agnd = dgnd = 0 v; xtal = 32.768 khz; input logic 0 = 0 v, logic 1 = dv dd unless otherwise noted. limit at t min , t max parameter (b version) unit conditions/comments t 1 32.768 khz typ crystal oscillator frequency t 2 50 ns min reset pulsewidth read operation t 3 0 ns min rdy to cs setup time t 4 0 ns min cs falling edge to sclk active edge setup time 3 t 5 4 0 ns min sclk active edge to data valid delay 3 60 ns max dv dd = 4.5 v to 5.5 v 80 ns max dv dd = 2.7 v to 3.6 v t 5a 4, 5 0 ns min cs falling edge to data valid delay 3 60 ns max dv dd = 4.5 v to 5.5 v 80 ns max dv dd = 2.7 v to 3.6 v t 6 100 ns min sclk high pulsewidth t 7 100 ns min sclk low pulsewidth t 8 0 ns min cs rising edge to sclk inactive edge hold time 3 t 9 6 10 ns min bus relinquish time after sclk inactive edge 3 80 ns max t 10 100 ns max sclk active edge to rdy high 3, 7 write operation t 11 0 ns min cs falling edge to sclk active edge setup time 3 t 12 30 ns min data valid to sclk edge setup time t 13 25 ns min data valid to sclk edge hold time t 14 100 ns min sclk high pulsewidth t 15 100 ns min sclk low pulsewidth t 16 0 ns min cs rising edge to sclk edge hold time notes 1 sample tested during initial release to ensure compliance. all input signals are specified with tr = tf = 5 ns (10% to 90% of d v dd ) and timed from a voltage level of 1.6 v. 2 see figures 1 and 2. 3 sclk active edge is falling edge of sclk. 4 these numbers are measured with the load circuit of figure 1 and defined as the time required for the output to cross the v ol or v oh limits. 5 this specification only comes into play if cs goes low while sclk is low. it is required primarily for interfacing to dsp machi nes. 6 these numbers are derived from the measured time taken by the data output to change 0.5 v when loaded with the load circuit of f igure 1. the measured number is then extrapolated back to remove effects of charging or discharging the 50 pf capacitor. this means that the times quoted in th e timing characteristics are the true bus relinquish times of the part and as such are independent of external bus loading capacitances. 7 rdy returns high after the first read from the device after an output update. the same data can be read again, if required, while rdy is high, although care should be taken that subsequent reads do not occur close to the next output update. specifications subject to change without notice. to output pin 50pf i sink i source 1.6v (1.6ma with dv dd = 5v 100 a with dv dd = 3v) (200 a with dv dd = 5v 100 a with dv dd = 3v) figure 1. load circuit for timing characterization rev. 0 C10C ad7708/AD7718 absolute maximum ratings * (t a = 25 c unless otherwise noted) av dd to agnd . . . . . . . . . . . . . . . . . . . . . . . C0.3 v to +7 v av dd to dgnd . . . . . . . . . . . . . . . . . . . . . . . C0.3 v to +7 v dv dd to agnd . . . . . . . . . . . . . . . . . . . . . . . C0.3 v to +7 v dv dd to dgnd . . . . . . . . . . . . . . . . . . . . . . . C0.3 v to +7 v agnd to dgnd . . . . . . . . . . . . . . . . . . C0.05 v to +0.05 v av dd to dv dd . . . . . . . . . . . . . . . . . . . . . . . . . C5 v to +5 v analog input voltage to agnd . . . . C0.3 v to av dd +0.3 v reference input voltage to agnd . . C0.3 v to av dd +0.3 v total ain/refin current (indefinite) . . . . . . . . . . . . 30 ma digital input voltage to dgnd . . . . C0.3 v to dv dd +0.3 v digital output voltage to dgnd . . . C0.3 v to dv dd +0.3 v operating temperature range . . . . . . . . . . . C40 c to +85 c storage temperature range . . . . . . . . . . . . C65 c to +150 c junction temperature . . . . . . . . . . . . . . . . . . . . . . . . . 150 c soic package ja thermal impedance . . . . . . . . . . . . . . . . . . . 71.4 c/w jc thermal impedance . . . . . . . . . . . . . . . . . . . . . 23 c/w tssop package ja thermal impedance . . . . . . . . . . . . . . . . . . . 97.9 c/w jc thermal impedance . . . . . . . . . . . . . . . . . . . . . 14 c/w lead temperature, soldering vapor phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . . . 215 c infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220 c * stresses above those listed under absolute maximum ratings may cause perma- nent damage to the device. this is a stress rating only; functional operation of the device at these or any other conditions above those listed in the operational sections of this specification is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. caution esd (electrostatic discharge) sensitive device. electrostatic charges as high as 4000 v readily accumulate on the human body and test equipment and can discharge without detection. although the ad7708/AD7718 features proprietary esd protection circuitry, permanent damage may occur on devices subjected to high-energy electrostatic discharges. therefore, proper esd precautions are recommended to avoid performance degradation or loss of functionality. warning! esd sensitive device ordering guide temperature package package model range description option ad7708br C40 c to +85 c soic r-28 ad7708bru C40 c to +85 c tssop ru-28 eval-ad7708eb evaluation board AD7718br C40 c to +85 c soic r-28 AD7718bru C40 c to +85 c tssop ru-28 eval-AD7718eb evaluation board rev. 0 ad7708/AD7718 C11C t 12 t 13 t 14 t 15 t 11 t 16 msb lsb cs sclk din figure 2. write cycle timing diagram t 5 t 5a t 4 t 6 t 3 t 9 msb lsb cs sclk t 8 t 10 t 7 t 6 dout rdy figure 3. read cycle timing diagram rev. 0 C12C ad7708/AD7718 pin function descriptions pin no mnemonic function 1 ain7 analog input channel 7. pro grammable-gain analog input that can be used as a pse udo- differential input when used with aincom, or as the positive input of a fully-differential input pair when used with ain8. (see adc control register section.) 2 ain8 analog input channel 8. program mable-gain analog input that can be used as a ps eudo- differential input when used with aincom, or as the negative input of a fully-differential input pair when used with ain7. (see adc control register section.) 3av dd analog supply voltage 4 agnd analog ground 5 refin1(C) negative reference input. this reference input can lie anywhere between agnd and av dd C 1 v. 6 refin1(+) positive reference input. refin(+) can lie anywhere between av dd and agnd. the nominal reference voltage [refin(+)Crefin(C)] is 2.5 v but the part is functional with a reference range from 1 v to av dd . 7 ain1 analog input channel 1. programmable-gain analog input that can be used as a ps eudo- differential input when used with aincom, or as the positive input of a fully-differential input pair when used with ain2. (see adc control register section.) 8 ain2 analog input channel 2. programmable-gain analog input that can be used as a pseudo- differential input when used with aincom, or as the negative input of a fully-differential input pair when used with ain1. (see adc control register section.) 9 ain3 analog input channel 3. programmable-gain analog input that can be used as a ps eudo- differential input when used with aincom, or as the positive input of a fully-differential input pair when used with ain4. (see adc control register section.) 10 ain4 analog input channel 4. progra mmable-gain analog input that can be used as a pseudo- differential input when used with aincom, or as the negative input of a fully-differential input pair when used with ain3. (see adc control register section.) 11 ain5 analog input channel 5. programmable-gain analog input that can be used as a pse udo- differential input when used with aincom, or as the positive input of a fully-differential input pair when used with ain6. (see adc control register section adccon.) 12 aincom all analog inp uts are referenced to this input when confi gured in pseudo-differential input mode. 13 refin2(+)/ain9 positive reference input/analog input. this input can be configured as a reference input with the same charact eristics as refin1(+) or as an additional analog input. when con figured as an analog input this pin provides a programmable-gain analog input that can be used as a pseudo- differential input when used with aincom, or as the positive input of a fully-differential input pair when used with ain10. (see adc control register section.) 14 refin2(C)/ain10 negative reference inp ut/analog input. this pin can be configured as a reference or analog input. when configured as a reference input it provides the negative reference input for refin2. when configured as an analog input it provides a programmable-gain analog input that can be used as a pseudo-differential input when used with aincom, or as the negative input of a fully- differential input pair when used with ain9. (see adc control register section.) 15 ain6 analog input channel 6. programmable-gain analog input that can be used as a pseudo- differential input when used with aincom, or as the negative input of a fully-differential input pair when used with ain5. (see adc control register section.) 16 p2 p2 can act as a general-purpose input/output bit referenced between av dd and agnd. there is a weak pull-up to av dd internally on this pin. 17 agnd it is recommended that this pin be tied directly to agnd. 18 p1 p1 can act as a general-purpose input/output bit referenced between av dd and agnd. there is a weak pull-up to av dd internally on this pin. 19 reset digital input used to reset the adc to its power-on-reset status. this pin has a weak pull-up internally to dv dd . 20 sclk serial clock input for data tran sfers to and from the adc. the sclk has a schmitt-trigger input making an opto-isolated interface more robust. the serial clock can be continuous with all data transmitted in a continuous train of pulses. alternatively, it can be a noncontinuous clock with the information being transmitted to or from the ad 7708/AD7718 in smaller batches of data. rev. 0 ad7708/AD7718 C13C pin no mnemonic function 21 cs chip select input. this is an active low logic input used to select the ad7708/AD7718. cs can be used to select the ad7708/AD7718 in systems with more than one device on the serial bus or as a frame syn chronization signal in communicating with the devi ce. cs can be hardwired low, allowing the ad7708/AD7718 to be operated in 3-wire mode with sclk, din, and dout used to interface with the device. 22 rdy rdy is a logic low status output from the ad7708/AD7718. rdy is low when valid data exists in the data register for the selected channel. this output returns high on completion of a read operation from the data register. if data is not read, rdy will return high prior to the next u pdate indicating to the user that a read operation should not be initiated. the rdy pin also returns low following the completion of a calibration cycle. rdy does not return high after a calibration until the mode bits are written to enabling a new conversion or calibration. 23 dout serial data output with serial data being read from the output shift register of the adc. the output shift register can contain data from any of the on-chip data, calibration or control registers. 24 din serial data input with serial data being written to the input shift register on the ad7708/AD7718 data in this shift register is transferred to the calibration or control registers within the adc depending on the selection bits of the communications register. 25 dgnd ground reference point for the digital circuitry. 26 dv dd digital supply voltage, 3 v or 5 v nominal. 27 xtal2 output from the 32 khz crystal oscillator or resonator inverter. 28 xtal1 input to the 32 khz crystal oscillator or resonator inverter. pin configuration 14 13 12 11 17 16 15 20 19 18 10 9 8 1 2 3 4 7 6 5 top view (not to scale) 28 27 26 25 24 23 22 21 ad7708/ AD7718 ain7 dgnd dv dd xtal2 xtal1 ain8 av dd agnd rdy dout din refin1( ) refin1(+) ain1 ain2 ain3 ain4 reset sclk cs ain5 aincom refin2(+)/ain9 refin2( )/ain10 p1 ain6 p2 agnd rev. 0 C14C ad7708/AD7718 reading number 8389600 8389400 8388000 0 1000 100 code read 200 300 8389200 400 500 600 700 800 900 8389000 8388800 8388600 8388400 8388200 av dd = dv dd = 5v input range = 20mv refin1(+) refin1( ) = 2.5v update rate = 19.79hz t a = 25 c v ref = 2.5v rms noise = 0.58 v rms tpc 1. AD7718 typical noise plot on 20 mv input range with 19.79 hz update rate 8 7 0 8388039 8388721 8388687 8388657 8388615 8388579 8388547 8388499 8388449 8388382 8388754 8389110 8389033 8388985 8388941 8388906 8388874 8388841 8388805 8388779 6 5 4 3 2 1 9 tpc 2. AD7718 noise distribution histogram 2.5 0 1.0 3.0 2.5 2.0 1.5 3.5 5.0 4.5 4.0 2.0 1.5 1.0 0.5 3.0 v ref v rms noise v 20mv range 2.56v range av dd = dv dd = 5v v ref = 2.5v input range = 2.56v update rate = 19.79hz t a = 25 c tpc 3. rms noise vs. reference input (AD7718 andad7708) 16 040 30 20 10 50 100 90 80 70 60 24 22 20 18 26 update rate hz no missing codes min 110 chop = 0 tpc 4. AD7718 no-missing codes performance 32767 100 0 200 400 300 32771 32770 32769 32768 32772 reading number code read 500 32766 32765 32764 600 700 800 900 1000 av dd = dv dd = 5v input range = 20mv update rate = 19.79hz v ref = 2.5v t a = 25 c tpc 5. ad7708 typical noise plot on 20 mv input range 200 32767 32766 32768 32770 32769 600 500 400 300 700 code occurrence 32771 100 0 tpc 6. ad7708 noise histogram typical performance characteristics rev. 0 ad7708/AD7718 C15C adc circuit information the ad7708/AD7718 incorporates a 10-channel multiplexer with a sigma-delta adc, on-chip programmable gain amplifier and digital filtering intended for the measurement of wide dynamic range, low frequency signals such as those in weigh-scale, strain-gauge, pressure transducer, or temperature measurement applications. the ad7708 offers 16-bit resolution while the AD7718 offers 24-bit resolution. the AD7718 is a pin-for-pin compatible version of the ad7708. the AD7718 offers a direct upgradable path from a 16-bit to a 24-bit system without requiring any hardware changes and only minimal software changes. these parts can be configured as four/five fully-differential input channels or as eight/ten pseudo-differential input chan- nels referenced to aincom. the channel is buffered and can be programmed for one of eight input ranges from 20 mv to 2.56 v. buffering the input channel means that the part can handle significant source impedances on the analog input and that r, c filtering (for noise rejection or rfi reduction) can be placed on the analog inputs if required. these input channels are intended to convert signals directly from sensors without the need for external signal conditioning. the adc employs a sigma-delta conversion technique to realize up to 24 bits of no missing codes performance. the sigma-delta modulator converts the sampled input signal into a digital pulse train whose duty cycle contains the digital information. a sinc 3 programmable low-pass filter is then employed to decimate the modulator output data stream to give a valid data conversion result at programmable output rates. the signal chain has two modes of operation, chop enabled and chop disabled. the chop bit in the mode register enables and disables the chopping scheme. signal chain overview (chop enabled, chop = 0) with chop = 0, chopping is enabled, this is the default and gives optimum performance in terms of drift performance. with chop ping enabled, the available output rates vary from 5.35 hz (186.77 ms) to 105.03 hz (9.52 ms). a block diagram of the adc input channel with chop enabled is shown in figure 4. the sampling frequency of the modulator loop is many times higher than the bandwidth of the input signal. the integrator in the modulator shapes the quantization noise (which results from the analog-to-digital conversion) so that the noise is pushed toward one-half of the modulator frequency. the output of the sigma-delta modulator feeds directly into the digital filter. the digital filter then band-limits the response to a frequency signifi- cantly lower than one-half of the modulator frequency. in this manner, the 1-bit output of the comparator is translated into a band limited, low noise output from the ad7708/AD7718 adc. the ad7708/AD7718 filter is a low-pass, sinc 3 or (sinx/x) 3 filter whose primary function is to remove the quantization noise introduced at the modulator. the cutoff frequency and deci- mated output data rate of the filter are programmable via the sf word loaded to the filter register. the complete signal chain is chopped resulting in excellent dc offset and offset drift specifica- tions and is extremely beneficial in applications where drift, noise rejection, and optimum emi rejection are important factors. with chopping, the adc repeatedly reverses its inputs. the decimated digital output words from the sinc 3 filters, therefore, have a positive offset and negative offset term included. as a result, a final summing stage is included so that each output word from the filter is summed and averaged with the previous filter output to produce a new valid output result to be written to the adc data register. the programming of the sinc 3 deci- mation factor is restricted to an 8-bit register sf, the actual decimation factor is the register value times 8. the decimated output rate from the sinc 3 filter (and the adc conversion rate) will therefore be f sf f adc mod = 1 3 1 8 where f adc in the adc conversion rate. sf is the decimal equivalent of the word loaded to the filter register. f mod is the modulator sampling rate of 32.768 khz. the chop rate of the channel is half the output data rate: f f chop adc = 1 2 as shown in the block diagram, the sinc 3 filter outputs alter- nately contain +v os and Cv os , where v os is the respective channel offset. this offset is removed by performing a running average of two. this average by two means that the settling time to any ch ange in programming of the adc will be twice the normal conversion time, while an asynchronous step change on the analog input will not be fully reflected until the third subse- quent output. t f t settle adc adc == 2 2 the allowable range for sf is 13 to 255 with a default of 69 (45h). the corresponding conversion rates, conversion times, and settling times are shown in table i. note that the conver- sion time increases by 0.732 ms for each increment in sf. sinc 3 filter mux buf pga - mod0 xor analog input digital output 1 8 sf 3 (8 sf ) 3 1 2 a in + v os a in v os f chop f in f mod f chop f adc ( ( figure 4. adc channel block diagram with chop enabled rev. 0 C16C ad7708/AD7718 table i. adc conversion and settling times for various sf words with chop = 0 sf data update rate settling time word f adc (hz) t settle (ms) 13 105.3 19.04 23 59.36 33.69 27 50.56 39.55 45 30.3 65.9 69 (default) 19.79 101.07 91 15 133.1 182 7.5 266.6 255 5.35 373.54 the overall frequency response is the product of a sinc 3 and a sinc response. there are sinc 3 notches at integer multiples of 3 f adc and there are sinc notches at odd integer multiples of f adc /2. the 3 db frequency for all values of sf obeys the following equation: f (3 db ) = 0.24 f adc normal-mode rejection is the major function of the digital filter on the ad7708/AD7718. the normal mode 50 1 hz rejection with an sf word of 82 is typically C100 db. the 60 1 hz rejection with sf = 68 is typically C100 db. simultaneous 50 hz and 60 hz rejection of better than 60 db is achieved with an sf of 69. choosing an sf word of 69 places notches at both 50 hz and 60 hz. figures 5 to 9 show the filter rejection for a selection of sf words. the frequency response of the filter h (f) is as follows: 1 8 81 2 2 3 sf sf f f ff ff ff mod mod out out ? ? ? ? ? ? ? ? ? ? ? ? sin ( / ) sin ( / ) sin ( / ) sin ( / ) where f mod = 32,768 hz, sf = value programmed into sf register, f out = f mod /(sf 8 3). the following plots show the filter frequency response for a variety of update rates from 5 hz to 105 hz. frequency hz 0 140 200 0 650 50 100 150 200 250 300 350 400 450 500 550 600 700 attenuation db 20 120 160 180 60 100 40 80 sf = 13 output data rate = 105hz input bandwidth = 25.2hz first notch = 52.5hz 50hz rejection = 23.6db, 50hz 1hz rejection = 20.5db 60hz rejection = 14.6db, 60hz 1hz rejection = 13.6db figure 5. filter profile with sf = 13 frequency hz 0 80 160 0 100 10 attenuation db 20 30 40 50 60 70 80 90 20 40 120 140 60 100 sf = 82 output data rate = 16.65hz input bandwidth = 4hz 50hz rejection = 171db, 50hz 1hz rejection = 100db 60hz rejection = 58db, 60hz 1hz rejection = 53db figure 6. filter profile with sf = 82 rev. 0 ad7708/AD7718 C17C frequency hz 0 80 160 0 100 10 attenuation db 20 30 40 50 60 70 80 90 20 40 120 140 60 100 sf = 255 output data rate = 5.35hz input bandwidth = 1.28hz 50hz rejection = 93db, 50hz 1hz rejection = 93db 60hz rejection = 74db, 60hz 1hz rejection = 68db figure 7. filter profile with sf = 255 frequency hz 0 80 160 0 100 10 attenuation db 20 30 40 50 60 70 80 90 20 40 120 140 60 100 sf = 69 output data rate = 19.8hz input bandwidth = 4.74hz first notch = 9.9hz 50hz rejection = 66db, 50hz 1hz rejection = 60db 60hz rejection = 117db, 60hz 1hz rejection = 94db figure 8. filter profile with default sf = 69 giving filter notches at both 50 hz and 60 hz frequency hz 0 80 160 0 100 10 attenuation db 20 30 40 50 60 70 80 90 20 40 120 140 60 100 sf = 68 output data rate = 20.07hz input bandwidth = 4.82hz 50hz rejection = 74db, 50hz 1hz rejection = 54.6db 60hz rejection = 147db, 60hz 1hz rejection = 101db figure 9. filter profile with sf = 68 adc noise performance chop enabled ( chop = 0) tables ii to v show the output rms noise and output peak-to- peak resolution in bits (rounded to the nearest 0.5 lsb) for a selection of output update rates. the numbers are typical and generated at a differential input voltage of 0 v with av dd = dv dd = 5 v and using a 2.5 v reference. the output update rate is selected via the sf7Csf0 bits in the filter register. it is important to note that the peak-to-peak resolution figures repre- sent the resolution for which there will be no code flicker within a six-sigma limit. the output noise comes from two sources. the first is the electrical noise in the semiconductor devices (device noise) used in the implementation of the modulator. secondly, when the analog input is converted into the digital domain, quantization noise is added. the device noise is at a low level and is independent of frequency. the quantization noise starts at an even lower level but rises rapidly with increasing frequency to become the dominant noise source. the numbers in the tables are given for the bipolar input ranges. for the unipolar ranges the rms noise numbers will be the same as the bipolar range, but the peak-to-peak resolution is now based on half the signal range which effectively means losing one bit of resolution. rev. 0 C18C ad7708/AD7718 table ii. typical output rms noise vs. input range and update rate for AD7718 with chop enabled ( chop = 0); output rms noise in v sf data update input range word rate (hz) 20 mv 40 mv 80 mv 160 mv 320 mv 640 mv 1.28 v 2.56 v 13 105.3 1.50 1.50 1.60 1.75 3.50 4.50 6.70 11.75 23 59.36 1.0 1.02 1.06 1.15 1.22 1.77 3.0 5.08 27 50.56 0.95 0.95 0.98 1.00 1.10 1.66 5.0 69 19.79 0.60 0.65 0.65 0.65 0.65 0.95 1.40 2.30 255 5.35 0.35 0.35 0.37 0.37 0.37 0.51 0.82 1.25 table iii. peak-to-peak resolution vs. input range and update rate for AD7718 with chop enabled ( chop = 0); peak-to-peak resolution in bits sf data update input range word rate (hz) 20 mv 40 mv 80 mv 160 mv 320 mv 640 mv 1.28 v 2.56 v 13 105.3 12 13 14 15 15 15.5 16 16 23 59.36 12.5 13.5 14.5 15 16 17 17 17 27 50.56 12.5 13.5 14.5 15.5 16.5 17 17 17 69 19.79 13 14 15 16 17 17.5 18 18.5 255 5.35 14 15 16 17 18 18.5 18.8 19.2 table iv. typical output rms noise vs. input range and update rate for ad7708 with chop enabled ( chop = 0); output rms noise in v sf data update input range word rate (hz) 20 mv 40 mv 80 mv 160 mv 320 mv 640 mv 1.28 v 2.56 v 13 105.3 1.50 1.50 1.60 1.75 3.50 4.50 6.70 11.75 23 59.36 1.0 1.02 1.06 1.15 1.22 1.77 3.0 5.08 27 50.56 0.95 0.95 0.98 1.00 1.10 1.66 5.0 69 19.79 0.60 0.65 0.65 0.65 0.65 0.95 1.40 2.30 255 5.35 0.35 0.35 0.37 0.37 0.37 0.51 0.82 1.25 table v. peak-to-peak resolution vs. input range and update rate for ad7708 with chop enabled ( chop = 0); peak-to-peak resolution in bits sf data update input range word rate (hz) 20 mv 40 mv 80 mv 160 mv 320 mv 640 mv 1.28 v 2.56 v 13 105.3 12 13 14 15 15 15.5 16 16 23 59.35 12.5 13.5 14.5 15 16 16 16 16 27 50.56 12.5 13.5 14.5 15.5 16 16 16 16 69 19.79 13 14 15 16 16 16 16 16 255 5.35 14 15 16 16 16 16 16 16 rev. 0 ad7708/AD7718 C19C signal chain overview chop disabled ( chop = 1) with chop =1 chopping is disabled. with chopping disabled the available output rates vary from 16.06 hz (62.26 ms) to 1365.33 hz (0.73 ms). the range of applicable sf words is from 3 to 255. w hen switching between channels with chop disabled, the channel throughput is increased by a factor of two over the case where chop is enabled. when used in m ultiplexed applica- tions operation with chop disabled w ill offer the best throughput time when cycling through all channels. the drawback with chop disabled is that the drift performance is degraded and calibration is required following a gain change or significant temperature change. a block d iagram of the adc input channel with chop disabled is shown in figure 10. the signal chain includes a mux, buffer, pga, sigma-delta m odu- lator, and digital filter. the modulator bit stream is applied to a sinc 3 filter. the programming of the sinc 3 decimation factor is restricted to an 8-bit register sf, the actual decima- tion factor is the register value times 8. the decimated output rate from the sinc 3 filter (and the adc conversion rate) will there- fore be: f f sf adc mod = 8 where f adc is the adc conversion rate, sf is the decimal equivalent of the word loaded to the filter register, valid range is from 3 to 255, f mod is the modulator sampling rate of 32.768 khz. the settling time to a step input is governed by the digital filter. a synchronized step change will require a se ttling time of three times the programmed update rate, a channel change can be treated as a synchronized step change. an unsynchronized step change will require four outputs to reflect the new analog input at its output. t f t settle adc adc == 3 3 the allowable range for sf is 3 to 255 with a default of 69 (45h). the corresponding conversion rates, conversion times, and settling times are shown in table vi. note that the conver- sion time increases by 0.245 ms for each increment in sf. table vi. adc conversion and settling times for various sf words with chop = 1 sf data update rate settling time word f adc (hz) t settle (ms) 03 1365.33 2.20 68 60.2 49.8 69 (default) 59.36 50.54 75 54.6 54.93 82 49.95 60 151 27.13 110.6 255 16.06 186.76 the frequency response of the digital filter h (f) is as follows: 1 8 8 3 sf sf f f ff mod mod ? ? ? ? ? ? sin( / ) sin( / ) where f mod = 32,768 hz, sf = value programmed into sf sfr. the following shows plots of the filter frequency response using different sf words for output data rates of 16 hz to 1.36 khz. there are sinc 3 notches at integer multiples of the update rate. the 3 db frequency for all value s of s f obeys the following equation: f (3 db ) = 0.262 f adc the following plots show frequency response of the ad7708/ AD7718 digital filter for various filter words. the ad7708/ AD7718 are targeted at multiplexed applications. one of the key requirements in these applications is to optimize the sf word to obtain the maximum filter rejection at 50 hz and 60 hz while minimizing the channel throughput rate. figure 12 shows the ad7708/AD7718 optimized throughput while maximizing 50 hz and 60 hz rejection. this is achieved with an sf word of 75. in figure 13, by using a higher sf word of 151, 50 hz and 60 hz rejection can be maxim ized at 60 db with a channel throughput rate of 110 ms. an sf word of 255 gives maximum rejection at both 50 hz and 60 hz but the channel throughput rate is restricted to 186 ms as shown in figure 14. sinc 3 filter mux buf pga - mod0 analog input digital output f in f mod f adc figure 10. adc channel block diagram with chop disabled rev. 0 C20C ad7708/AD7718 frequency hz 0 80 160 0 100 10 attenuation db 20 30 40 50 60 70 80 90 20 40 120 140 60 100 sf = 68 output data rate = 60.2hz settling time = 49.8ms input bandwidth = 15.5hz 50hz rejection = 43db, 50hz 1hz rejection = 40db 60hz rejection = 147db, 60hz 1hz rejection = 101db 200 180 figure 11. frequency response operating with the sf word of 68 frequency hz 0 80 160 0 100 10 attenuation db 20 30 40 50 60 70 80 90 20 40 120 140 60 100 sf = 75 output data rate = 54.6hz settling time = 55ms input bandwidth = 14.3hz 50hz rejection = 62.5db, 50hz 1hz rejection = 57db 60hz rejection = 63db, 60hz 1hz rejection = 60db 200 180 figure 12. optimizing filter response for throughput while maximizing the simultaneous 50 hz and 60 hz rejection frequency hz 0 80 160 0 100 10 attenuation db 20 30 40 50 60 70 80 90 20 40 120 140 60 100 sf = 151 output data rate = 27.12hz settling time = 110ms input bandwidth = 27.12hz 50hz rejection = 65.4db, 50hz 1hz rejection = 60db 60hz rejection = 63db, 60hz 1hz rejection = 60db 200 180 figure 13. optimizing filter response for maximum simultaneous 50 hz and 60 hz rejection frequency hz 0 80 160 0 100 10 attenuation db 20 30 40 50 60 70 80 90 20 40 120 140 60 100 sf = 255 output data rate = 16.06hz settling time = 186ms input bandwidth = 4.21hz 50hz rejection = 87db, 50hz 1hz rejection = 77db 60hz rejection = 72db, 60hz 1hz rejection = 68db 200 180 figure 14. frequency with maximum sf word = 255 adc noise performance chop disabled ( chop = 1) tables vii to x show the output rms noise and output peak-to- peak resolution in bits (rounded to the nearest 0.5 lsb) for some typical output update rates. the numbers are typical and generated at a differential input voltage of 0 v. the output update rate is selected via the sf7Csf0 bits in the filter register. it is important to note that the peak-to-peak resolution figures repre sent the resolution for which there will be no code flicker within a six-sigma limit. the output noise comes from two sources. the first is the electrical noise in the semiconductor devices (device noise) used in the implementation of the modulator. secondly, when the analog input is converted into the digital domain, quantization noise is added. the device noise is at a low level and is independent of frequency. the quantization noise starts at an even lower level but rises rapidly with increasing frequency to become the dominant noise source. the numbers in the tables are given for the bipolar input ranges. for the unipolar ranges the rms noise numbers will be the same as the bipolar range, but the peak-to-peak resolution is now based on half the signal range which effectively means losing 1 bit of resolution. rev. 0 ad7708/AD7718 C21C table vii. typical output rms noise vs. input range and update rate for AD7718 with chop disabled ( chop = 1); output rms noise in v sf data update input range word rate (hz) 20 mv 40 mv 80 mv 160 mv 320 mv 640 mv 1.28 v 2.56 v 03 1365.33 30.31 29.02 58.33 112.7 282.44 361.72 616.89 1660 13 315.08 2.47 2.49 2.37 3.87 7.18 12.61 16.65 32.45 66 62.06 0.743 0.852 0.9183 0.8788 0.8795 1.29 1.99 3.59 69 59.38 0.961 0.971 0.949 0.922 0.923 1.32 2.03 3.73 81 50.57 0.894 0.872 0.872 0.806 0.793 1.34 2.18 2.96 255 16.06 0.475 0.468 0.434 0.485 0.458 0.688 1.18 1.78 table viii. peak-to-peak resolution vs. input range and update rate for AD7718 with chop disabled ( chop = 1); peak-to-peak resolution in bits sf data update input range word rate (hz) 20 mv 40 mv 80 mv 160 mv 320 mv 640 mv 1.28 v 2.56 v 03 1365.33 8999 9 9 9 9 13 315.08 11 12 14 14 14 14 15 15 66 62.06 13 14 15 16 17 17 18 18 69 59.36 13 14 15 16 17 17 18 18 81 50.57 13 14 15 16 17 17 18 18 255 16.06 14 15 16 17 18 18 19 19 table ix. typical output rms noise vs. input range and update rate for ad7708 with chop disabled ( chop = 1); output rms noise in v sf data update input range word rate (hz) 20 mv 40 mv 80 mv 160 mv 320 mv 640 mv 1.28 v 2.56 v 03 1365.33 30.31 29.02 58.33 112.7 282.44 361.72 616.89 1660 13 315.08 2.47 2.49 2.37 3.87 7.18 12.61 16.65 32.45 66 62.06 0.743 0.852 0.9183 0.8788 0.8795 1.29 1.99 3.59 69 59.38 0.961 0.971 0.949 0.922 0.923 1.32 2.03 3.73 81 50.57 0.894 0.872 0.872 0.806 0.793 1.34 2.18 2.96 255 16.06 0.475 0.468 0.434 0.485 0.458 0.688 1.18 1.78 table x. peak-to-peak resolution vs. input range and update rate for ad7708 with chop disabled ( chop = 1); peak-to-peak resolution in bits sf data update input range word rate (hz) 20 mv 40 mv 80 mv 160 mv 320 mv 640 mv 1.28 v 2.56 v 03 1365.33 8999 9 9 9 9 13 315.08 11 12 14 14 14 14 15 15 66 62.06 13 14 15 16 16 16 16 16 69 59.36 13 14 15 16 16 16 16 16 81 50.57 13 14 15 16 16 16 16 16 255 16.06 14 15 16 16 16 16 16 16 rev. 0 C22C ad7708/AD7718 on-chip registers the ad7708 and AD7718 are controlled and configured via a number of on-chip registers which are shown in figure 15. the first of these registers is the communications register which is used to control all operations on these converters. all communications with these parts must start with a write to the communications register to specify the next operation to be performed. after a power-on or reset, the device defaults to waiting for a write to the communications register. the status register contains information pertaining to the operat- ing conditions of the converter. the status register is a read only register. the mode register is used to configure the con- version mode, calibration, chop enable/disable, reference select, channel configuration and buffered or unbuffered operation on the aincom analog input. the mode register is a read/write register. the adc control register is a read/write register used to select the active channel and program its input range and bipolar/unipolar operation. the i/o control register is a read/ write register used to configure the operation of the 2-pin i/o port. the filter register is a read/write register used to program the data update rate of the converter. the adc data register is a read only register that contains the result of a data conversion on the selected channel. the adc offset registers are read/write registers that contain the offset calibration data. there are five offset registers, one for each of the fully differential input channels. when configured for pseudo-differential input mode the chan- nels share offset registers. the adc gain registers are read/write registers that contain the gain calibration data. there are five adc gain registers, one for each of the fully differential input channels. when configured for pseudo differential input mode the channels share gain registers. the adc contains test registers for factory use only, the user is advised not to alter the oper- ating conditions of these registers. the id register is a read only register and is used for silicon identification purposes. the follow- ing sections contains more in-depth detail on all of these registers. in the following descriptions, set implies a logic 1 s tate and cleared implies a logic 0 state unless otherwise stated. dout dout dout din dout din dout din dout din dout dout din dout dout wen r/ w 00 a1 a2 a3 a0 communications register dout din din register select decoder adc data register status register mode register adc control register i/o control register filter register id register test register adc gain register adc offset register din din figure 15. on-chip registers rev. 0 ad7708/AD7718 C23C table xi. registers?uick reference guide power-on/reset register name type size default value function communications write only 8 bits not applicable all operations to other registers are initiated through the communications register. this controls whether subsequent operations are read or write operations and also selects the register for that subsequent operation. status register read only 8 bits 00 hex provides status information on conversions, calibra- tions and error conditions. mode register read/write 8 bits 00 hex controls functions such as mode of operation, chan- nel configuration, oscillator operation in power-down. adc (adccon) control register read/write 8 bits 07 hex t his register is used to select the active channel input, configure the operating input range, and select unipolar or bipolar operation. i/o (iocon) i/o control register read/write 8 bits 00 hex t his register is used to control and configure the i/o port. filter register read/write 8 bits 45 hex this register determines the amount of averaging performed by the sinc filter and consequently deter- mines the data update rate of the ad7708/AD7718. the filter register determines the update rate for operation with chop enabled and chop disabled. AD7718 adc (data) data register read only 24 bits 000000 hex provides the most up-to-date conversion result for the selected channel on the AD7718. ad7708 (data) data register read only 16 bits 0000 hex provides the most up-to-date conversion result for the selected channel on the ad7708. b s mb s l y d r0 l a c0r r e00 k c o l b s mb s l 3 h c2 h c1 h c0 h c/ u b 2 n r1 n r0 n r b s mb s l 7 f s6 f s5 f s4 f s3 f s2 f s1 f s0 f s b s mb s l 00 r i d 2 pr i d 1 p00 t a d 2 pt a d 1 p cr7 cr6 cr5 cr4 cr3 cr2 cr1 cr0 wen r/ w 0(0) 0(0) a3(0) a2(0) a1(0) a0(0) msb lsb chop negbuf refsel chcon oscpd md2 md1 md0 rev. 0 C24C ad7708/AD7718 table xi. registers quick reference guide (continued) power-on/reset register name type size default value function AD7718 offset register read/write 24 bits 800 000 hex contains a 24-bit word which is the offset calibration coefficient for the part. the contents of this register are used to provide offset correction on the output from the digital filter. there are five offset registers on the part and these are associated with input chan- nels as outlined in the adccon register. AD7718 gain register read/write 24 bits 5xxxx5 hex contains a 24-bit word which is the gain calibration coefficient for the part. the contents of this register are used to provide gain correction on the output from the digital filter. there are five gain registers on the part and these are associated with input chan- nels as outlined in the adccon register. ad7708 offset register read/write 16 bits 8000 hex contains a 16-bit word which is the offset calibration coefficient for the part. the contents of this register are used to provide offset correction on the output from the digital filter. there are five offset registers on the part and these are associated with input chan- nels as outlined in the adccon register. ad7708 gain register read/write 16 bits 5xxx hex contains a 16-bit word which is the gain calibration coefficient for the part. the contents of this register are used to provide gain correction on the output from the digital filter. there are five gain registers on the part and these are associated with input chan- nels as outlined in the adccon register. ad7708 id register read 8 bits 5x hex co ntains an 8-bit byte which is the identifier for the part. AD7718 id register read 8 bits 4x hex contains an 8-bit byte which is the identifier for the part. test registers read/write 16 bits 0000 hex controls the test modes of the part that are used when testing the part. the user is advised not to change the contents of these registers. rev. 0 ad7708/AD7718 C25C communications register (a3, a2, a1, a0 = 0, 0, 0, 0) the communications register is an 8-bit write-only register. all communications to the part must start with a write operation t o the communications register. the data written to the communications register determines whether the next operation is a read or wri te operation, the type of read operation, and on which register this operation takes place. for read or write operations, once the subse- quent read or write operation to the selected register is complete, the interface returns to where it expects a write operation to the communications register. this is the default state of the interface and, on power-up or after a reset , the ad7708/AD7718 is in this default state waiting for a write operation to the communications register. in situations where the interface sequence is lost, a write operation of at least 32 serial clock cycles with din high returns the ad7708/AD7718 to this default state by resetting t he part. table xii outlines the bit designations for the communications register. cr0 through cr7 indicate the bit location, cr denoting the bits are in the communications register. cr7 denotes the first bit of the data stream. 7 r c6 r c5 r c4 r c3 r c2 r c1 r c0 r c n e w ) 0 ( / r w ) 0 () 0 ( 0) 0 ( 0) 0 ( 3 a) 0 ( 2 a) 0 ( 1 a) 0 ( 0 a table xii. communications register bit designations bit bit location mnemonic description cr7 wen write enable bit. a 0 must be written to this bit so the write operation to the communications register actually takes place. if a 1 is written to this bit, the part will not clock on to subsequent bits in the regis ter. it will stay at this bit location until a 0 is written to this bit. once a 0 is written to the wen bit, the next seven bits will be loaded to the communications register. cr6 r/ w a zero in this bit location indicates that the next operation will be a write to a specified register. a one in this position indicates that the next operation will be a read from the designated register. cr5 0 a zero must be written to this bit position to ensure correct operation of the ad7708/AD7718. cr4 0 a zero must be written to this bit position to ensure correct operation of the ad7708/AD7718. cr3Ccr0 a3Ca0 register address bits. these address bits are used to select which of the ad7708/AD7718s registers are being accessed during this serial interface communication. a3 is the msb of the three selection bits. table xiii. register selection table a3 a2 a1 a0 register 0000comm unications register during a write operation 0000 status register during a read operation 0001m ode register 0010 adc control register 0011 filter register 0100 adc data register 0101 adc offset register 0110 adc gain register 0111i/o c ontrol register 1000un defined 1001un defined 1010un defined 1011un defined 1100t est 1 register 1101t est 2 register 1110un defined 1111id r egister rev. 0 C26C ad7708/AD7718 status register (a3, a2, a1, a0 = 0, 0, 0, 0; power-on-reset = 00hex) the adc status register is an 8-bit read-only register. to access the adc status register, the user must write to the communica - tions register selecting the next operation to be a read and load bits a3-a0 with 0, 0, 0,0. table xiv outlines the bit designa tions for the status register. sr0 through sr7 indicate the bit location, sr denoting the bits are in the status register. sr7 denote s the first bit of the data stream. the number in brackets indicates the power-on/reset default status of that bit. r s7 6 r s5 r s4 r s3 r s2 r s1 r s0 r s y d r) 0 () 0 ( 0) 0 ( l a c) 0 ( 0) 0 ( r r e) 0 ( 0) 0 ( 0) 0 ( k c o l table xiv. status register bit designations bit bit location mnemonic description sr7 rdy ready bit for the adc set when data is transferred to the adc data registers or on completion of calibration cycle. the rdy bit is cleared automatically a period of time before the data register is updated with a new conversion result or after the adc data register has been read. this bit is also cleared by a write to the mode bits to indicate a conversion or calibration. the rdy pin is the complement of the rdy bit. sr6 0 bit is automatically cleared . reserved for future use sr5 cal calibration status bit set to indicate completion of calibration. it is set at the same time that the rdy is set high. cleared by a write to the mode bits to start another adc conversion or calibration. sr4 0 this bit is automatically cleared . reserved for future use sr3 err adc error bit set to indicate that the result written to the adc data register has been clamped to all zeros or all ones. after a calibration this bit also flags error conditions that caused the calibration registers not to be written. e rror sources include overrange. cleared by a write to the mode bits to initiate a conversion or calibration. sr2 0 this bit is automatically cleared . reserved for future use sr1 0 this bit is automatically cleared . reserved for future use sr0 lock pll lock status bit. set if the pll has locked onto the 32.768 khz crystal oscillator clock. if the user is worried about exact sampling frequencies etc., the lock bit should be interrogated and the result discarded if the lock bit is zero. rev. 0 ad7708/AD7718 C27C mode register (a3, a2, a1, a0 = 0, 0, 0, 1; power-on-reset = 00hex) the mode register is an 8-bit register from which data can be read or to which data can be written. this register configures th e operating modes of the ad7708/AD7718. table xv outlines the bit designations for the mode register. mr7 through mr0 indi- cate the bit location, mr denoting the bits are in the mode register. mr7 denotes the first bit of the data stream. the number in brackets indicates the power-on/reset default status of that bit. 7 r m6 r m5 r m4 r m3 r m2 r m1 r m0 r m p o h c ) 0 ( ) 0 ( f u b g e n) 0 ( l e s f e r) 0 ( n o c h c) 0 ( d p c s o) 0 ( 2 d m) 0 ( 1 d m) 0 ( 0 d m table xv. mode register bit designations bit bit location mnemonic description mr7 chop if this bit is cleared, chopping is enabled. when this bit is set chopping is disabled. the default is for chop enabled. mr6 negbuf this bit controls the operation of the input buffer on the aincom input when a channel is config- ured for pseudo-differential mode of operation. if cleared, the analog negative input (aincom) is unbuffered allowing it to be tied to agnd in single-ended input configuration. if this bit is set the analog negative input (aincom) is buffered, placing a restriction on its common-mode input range. mr5 refsel if this bit is cleared , the reference selected is refin1(+) and refin1(C) for the active channel. if this bit is set , the reference selected is refin2(+) and refin2(C) for the active channel. the con- tents of the chcon bit overrides the refsel bit. if the adc is configured in five fully-differential or 10 pseudo-differential input channel mode, the refsel bit setting is irrelevant as only one reference input is available. v ref select implemented using the refsel bit enables the user to perform both absolute and ratiometric measurements. mr4 chcon when cleared the device is configured as an 8-input channel converter, configured as eight pseudo- differential input channels with respect to aincom or four differential input arrangements with two reference input selection options. when set the device is configured as a 10 pseudo- differential input or a five differential input channel arrangement with a single reference input option. mr3 oscpd oscillator power-down bit. if this bit is set , placing the ad7708/AD7718 in standby mode will stop the crystal oscillator reducing the power drawn by these parts to a minimum. the oscillator will require 300 ms to begin oscillating when the adc is taken out of standby mode. if this bit is cleared , the oscillator is not shut off when the adc is put into standby mode and will not require the 300 ms start-up time when the adc is taken out of standby. mr2Cmr0 md2Cmd0 adc mode bits. these bits select the operational mode of the adc as follows: md2 md1 md0 0 0 0 power-down mode (power-on default) 0 0 1 idle mode in idle mode the adc filter and modulator are held in a reset state although the modulator clocks are still provided. 0 1 0 single conversion mode in single conversion mode, a single conversion is performed on the enabled channels. on comple- tion of the conversion the adc data registers are updated, the relevant flags in the status register are written, and idle mode is reentered with the md2Cmd0 being written accordingly to 001. 0 1 1 continuous conversion in continuous conversion mode, the adc data registers are regularly updated at the selected update rate (see filter register). 1 0 0 internal zero-scale calibration internal short automatically connected to the enabled channel(s) 1 0 1 internal full-scale calibration external v ref is connected automatically to the adc input for this calibration. 1 1 0 system zero-scale calibration user should connect system zero-scale input to the channel input pins as selected by ch3Cch0 bits in the control registers. 1 1 1 system full-scale calibration user should connect system full-scale input to the channel input pins as selected by ch3Cch0 bits in the control registers. rev. 0 C28C ad7708/AD7718 operating characteristics when addressing the mode and control registers 1. any change to the md bits will immediately reset the adcs. a write to the md2Cmd0 bits with no change is also treated as a re set. 2. once the mode has been written with a calibration mode, the rdy bit (status) is immediately reset and the calibration commences. on completion the appropriate calibration registers are written, the bit in status register is updated and the md2Cmd0 bits are reset to 001 to indicate the adc is back in idle mode. 3. calibrations are performed with the maximum allowable sf value with chop enabled. sf register is reset to user configuration after calibration with chop enabled. calibrations are performed with the selected value of sf when chop is disabled. adc control register (adccon): (a3, a2, a1, a0 = 0, 0, 1, 0; power-on-reset = 07 hex) the adc control register is an 8-bit register from which data can be read or to which data can be written. this register is use d to configure the adc for range, channel selection, and unipolar or bipolar coding. table xvi outlines the bit designations for the adc control register adccon7 through adccon0 indicate the bit location, adccon denoting the bits are in the adc control register. adccon7 denotes the first bit of the data stream. the number in brackets indicates the power-on/reset default status of that bit. table xvi. adc control register (adccon) bit designations bit bit location mnemonic description adccon7 ch3 adc channel selection bits. written by the user to select either pseudo-differential or fully- adccon6 ch2 differential input pairs used by the adc as follows: adccon5 ch1 adccon4 ch0 8-channel configuration 10-channel configuration (chcon = 0) (chcon = 1) positive negative cal register positive negative cal register ch3 ch2 ch1 ch0 input input pair input input pair 0 0 0 0 ain1 aincom 1 ain1 aincom 1 0 0 0 1 ain2 aincom 2 ain2 aincom 2 0 0 1 0 ain3 aincom 3 ain3 aincom 3 0 0 1 1 ain4 aincom 4 ain4 aincom 4 0 1 0 0 ain5 aincom 1 ain5 aincom 5 0 1 0 1 ain6 aincom 2 ain6 aincom 1 0 1 1 0 ain7 aincom 3 ain7 aincom 2 0 1 1 1 ain8 aincom 4 ain8 aincom 3 1 0 0 0 ain1 ain2 1 ain1 ain2 1 1 0 0 1 ain3 ain4 2 ain3 ain4 2 1 0 1 0 ain5 ain6 3 ain5 ain6 3 1 0 1 1 ain7 ain8 4 ain7 ain8 4 1 1 0 0 ain2 ain2 1 ain9 ain10 5 1 1 0 1 aincom aincom 1 aincom aincom 1 1 1 1 0 refin(+) refin(C) 1 ain9 aincom 4 1 1 1 1 open open 1 ain10 aincom 5 adccon3 u/ b unipolar/bipolar bit. set by user to enable unipolar coding i.e., zero differential input will result in 000000hex output and a full-scale differential input will result in ffffff hex output when operated in 24-bit mode. cleared by user to enable bipolar coding, negative full-scale differential input will result in an output code of 000000 hex, zero differential input will result in an output code of 800000 hex and a positive full-scale differential input will result in an output code of ffffff hex. adccon7 adccon6 adccon5 adccon4 adccon3 adccon2 adccon1 adccon0 ch3 (0) ch2 (0) ch1 (0) ch0 (0) u/ b (0) rn2 (1) rn1 (1) rn0 (1) rev. 0 ad7708/AD7718 C29C ad0c2 rn2 adc range bits ad0c1 rn1 written by the user to select the adc input range as follows ad0c0 rn0 rn2 rn1 rn0 selected adc input range (vref = 2.5 v) 000 20 mv 001 40 mv 010 80 mv 011 160 mv 100 320 mv 101 640 mv 110 1.28 v 111 2.56 v filter register (a3, a2, a1, a0 = 0, 0, 1, 1; power-on reset = 45hex) the filter register is an 8-bit register from which data can be read or to which data can be written. this register determines the amount of averaging performed by the sinc filter. table xvii outlines the bit designations for the filter register. fr7 through fr0 indicate the bit location, fr denoting the bits are in the filter register. fr7 denotes the first bit of the data stream. the n umber in brackets indicates the power-on/reset default status of that bit. the number in this register is used to set the decimation fac tor and thus the output update rate for the adcs. the filter register cannot be written to by the user the adc is active. the update ra te is used for the adcs is calculated as follows: f f chop enabled chop f sf f chop disabled chop adc mod adc mod = = = = () () 1 3 0 1 8 1 where f adc = adc output update rate, f mod = modulator clock frequency = 32.768 khz, sf = decimal value written to sf register. table xvii. filter register bit designations 7 r f6 r f5 r f4 r f3 r f2 r f1 r f0 r f ) 0 ( 7 f s6 f s) 1 (5 f s) 0 (4 f s) 0 (3 f s) 0 () 1 ( 2 f s) 0 ( 1 f s) 1 ( 0 f s the allowable range for sf is 13 decimal to 255 decimal with chop enabled, and the allowable sf range when chop is disabled is 03 decimal to 255 decimal. examples of sf values and corresponding conversion rate (f adc ) and time (t adc ) are shown in table xviii. it should be noted that optimum performance is obtained when operating with chop enabled. when chopping is enabled ( chop = 0), the filter register is loaded with ff hex during a calibration cycle. with chop disabled ( chop =1), the value in the filter register is used during calibration. table xviii. update rate vs. sf word chop enabled chop disabled sf (dec) sf (hex) f adc (hz) t adc (ms) f adc (hz) t adc (ms) 03 03 n/a n/a 1365.33 0.732 13 0d 105.3 9.52 315 3.17 69 45 19.79 50.34 59.36 16.85 255 ff 5.35 186.77 16.06 62.26 table xvi. adc control register (adccon) bit designations (continued) rev. 0 C30C ad7708/AD7718 i/o control register (iocon): (a3, a2, a1, a0 = 0, 1, 1, 1; power-on-reset = 00hex) the iocon register is an 8-bit register from which data can be read or to which data can be written. this register is used to c on- trol and configure the i/o port. table xix outlines the bit designations for this register. iocon7 through iocon0 indicate the bit location, iocon denoting the bits are in the i/o control register. iocon7 denotes the first bit of the data stream. the num - ber in brackets indicates the power-on/reset default status of that bit. a write to the iocon register has immediate effect and does not reset the adcs. 7 n o c o i6 n o c o i5 n o c o i4 n o c o i3 n o c o i2 n o c o i1 n o c o i0 n o c o i ) 0 (0) 0 () 0 ( r i d 2 pr i d 1 p) 0 (0) 0 () 0 ( 0) 0 ( t a d 2 p) 0 ( t a d 1 p table xix. iocon (i/o control register) bit designations bit bit location mnemonic description iocon7 0 this bit should always be cleared . reserved for future use. iocon6 0 this bit should always be cleared . reserved for future use. iocon5 p2dir p2, i/o direction control bit. set by user to enable p2 as an output. cleared by user to enable p2 as an input. there are weak pull-ups internally when enabled as an input. iocon4 p1dir p1, i/o direction control bit. set by user to enable p1 as an output. cleared by user to enable p1 as an input. there are weak pull-ups internally when enabled as an input. iocon3 0 this bit should always be cleared . reserved for future use. iocon2 0 this bit should always be cleared . reserved for future use. iocon1 p2dat digital i/o port (p1) data bit. the readback value of this bit indicates the status of the pin regardless of whether this pin is configured as an input or an output. the v alue written to this data bit will appear at the output port when the i/o pin is enabled as an output. iocon0 p1dat digital i/o port (p1) data bit. the readback value of this bit indicates the status of the pin, regardless of whether this pin is configured as an input or an output. the value written to this data bit will appear at the output port when the i/o pin is enabled as an output. adc data result register (data): (a3, a2, a1, a0 = 0, 1, 0, 0; power-on-reset = 000000hex) the conversion result for the selected adc channel is stored in the adc data register (data). this register is 16 bits wide on the ad7708 and 24 bits wide on the AD7718. this is a read only register. on completion of a read from this register the rdy bit in the status register is cleared. these adcs can be operated in either unipolar or bipolar mode of operation. unipolar mode in unipolar mode of operation the output coding is straight binary. with an analog input voltage of 0 v the output code is 0000hex for the ad7708 and 000000hex for the AD7718. with an analog input voltage of 1.024 v ref /gain the output code is ffffhex for the ad7708 and ffffff hex for the AD7718. the output code for any analog input voltage can be represented as follows: code = ( ain gain 2 n )/(1.024 v ref ) where ain is the analog input voltage and n = 16 for the ad7708 and n = 24 for the AD7718. rev. 0 ad7708/AD7718 C31C bipolar mode with an analog input voltage of (C1.024 v ref /gain), the output code is 0000 hex using the ad7708 and 000000h using the ad 7718. with an analog input voltage of 0 v, the output code is 8000hex for the ad7708 and 800000hex for the AD7718. with an analog input voltage of (+1.024 v ref /gain), the output code is ffff hex for the ad7708 and ffffff hex for the AD7718. note the analog inputs are pseudo bipolar inputs and the analog input voltage must remain within the common-mode input range at all time s. the output code for any analog input voltage can be represented as follows: code = 2 n C1 [( ain gain /1.024 v ref ) + 1] where ain is the analog input voltage, n = 16 for the ad7708, and n = 24 for the AD7718. adc offset calibration coefficient registers (of0): (a3, a2, a1, a0 = 0, 1, 0, 1; power-on-reset = 8000(00)hex) the offset calibration registers are 16-bit registers on the ad7708 and 24-bit registers on the AD7718. these registers hold th e offset calibration coefficient for the adc. the power-on-reset value of the internal zero-scale calibration coefficient registers is 8 000(00). there are five offset registers available, one for each of the fully differential input channels. calibration register pairs ar e shared when operating in pseudo-differential input mode. however, these bytes will be automatically overwritten if an internal or system ze ro-scale calibration is initiated by the user via md2Cmd0 bits in the mode register. the channel bits, in association with the communica tion register address for the of0 register, allow access to this register. this register is a read/write register. the calibration r egister can only be written to if the adc is inactive (md bits in the mode register = 000 or 001). reading of the calibration register does not clear the rdy bit. adc gain calibration coefficient register (gno): (a3, a2, a1, a0 = 0, 1, 1, 0; power-on-reset = 5xxx(x5) hex) the gain calibration registers are 16-bit registers on the ad7708 and 24-bit registers on the AD7718. these registers are confi gured at power-on with factory-calculated internal full-scale calibration coefficients. there are five full-scale registers available , one for each of the fully differential input channels. calibration register pairs are shared when operating in pseudo-differential input mod e. every device will have different default coefficients. however, these bytes will be automatically overwritten if an internal or syste m full-scale calibration is initiated by the user via md2Cmd0 bits in the mode register. the channel bits, in association with the communica tion register address, allow access to the data contained in the gn0 register. this is a read/write register. the calibration regist ers can only be written to if the adc is inactive (md bits in the mode register = 000 or 001). reading of the calibration registers doe s not clear the rdy bit. a calibration (self or system) is required when operating with chop mode disabled. id register (id): (a3, a2, a1, a0 = 1, 1, 1, 1; power-on-reset = 4x hex (AD7718) and 5x hex (ad7708) this register is a read only 8-bit register. the contents are used to determine the die revision of the silicon. table xx indic ates the bit locations for the ad7708. table xx. id register bit designation user nonprogrammable test registers the ad7708 and AD7718 contain two test registers. the bits in these test registers control the test modes of these adcs which a re used for the testing of the device. the user is advised not to change the contents of these registers . id7 id6 id5 id4 id3 id2 id1 id0 0 1 0 0/1 x x x x rev. 0 C32C ad7708/AD7718 configuring the ad7708/AD7718 all user-accessible registers on the ad7708 and AD7718 are accessed via the serial interface. communication with any of these registers is initiated by first writing to the communica- tions register. figures 16, 17, and 18 show flow diagrams for initializing the adc, a sequence for calibrating the adc chan- nels, and a routine that cycles through and reads all channels. figure 16 shows a flowchart detailing necessary programming steps required to initialize the adc. the following are the general programming steps required: 1. configure and initialize the microcontroller or microprocessor serial port. 2. initialize the ad7708/AD7718 by configuring the following registers: a. iocon to configure the digital i/o port. b. filter to configure the update rate for each channel. c. adccon to select the active input channel, select the analog input range, and select unipolar or bipolar operation. d. mode to configure the operating mode. the mode register selects chop or nonchop operation, buffered/ unbuffered operation of the aincom input, 8-/10- channel mode of operation and reference select along with the selection of conversion, calibration or idle modes of operation. all operations consist of a write to the communications register to specify the next operation as a write to a specified register. data is then written to the specified register. when each sequence is complete, the adc defaults to waiting for another write to the communications register to specify the next operation. write to communications register setting up next operation to be a write to the mode register. calibrate and select mode of operation write to communications register setting up next operation to be a write to the adc control register. configure adccon write to communications register setting up next operation to be a write to the filter register. set sf word for required update rate write to communications register selecting next operation to be a write to the iocon register and configure this register power-on/reset for ad7708/AD7718 configure and initialize c/ p serial port start figure 16. initializing ad7708/AD7718 end cal another channel write to mode register selecting full-scale calibration write to mode register selecting zero-scale calibration write to adccon selecting channel and configuring input range and unipolar/bipolar mode calibration routine md bits = 001? no yes md bits = 001? no yes yes no figure 17. calibrating the ad7708/AD7718 figure 17 shows a flowchart detailing necessary programming steps required when calibrating the ad7708/AD7718. the ad7708/AD7718 have dedicated calibration register pairs for each of the fully-differential input channels. having a dedicated register pair per channel allows each channel to be calibrated as part of the initialization and the adc picks up the relevant coefficients for each channel during normal operation. when operating is pseudo-differential mode channels share calibration register pairs. channels that share coefficients should be config- ured with the same operating conditions to avoid having to calibrate each time a channel is switched, especially with chop mode disabled. the ad7708/AD7718 are factory-calibrated with chop mode enabled and, therefore, if the adc is operated at the same conditions as the factory-calibration field calibra- tions will not be required. extremely low offset error and offset and gain drift errors are a by product of the chopping scheme. when operating with chop mode disabled, the user can achieve faster throughput times. an offset calibration is required with chop disabled when a gain or temperature change occurs. the following are the general programming steps required when calibrating a channel on the ad7708/AD7718. rev. 0 ad7708/AD7718 C33C 1. write to the adccon register to select the channel to be cali brated, its input range, and operation in unipolar or bipolar mode. 2. write to the mode register selecting chop or nonchop mode of operation, select the reference, buffered/unbuffered opera- tion on the aincom, and select zero-scale offset calibration. zero-scale calibration can be either self-calibration, where the adc determines the zero point internal to the adc, or a system calibration where the user must supply the zero-scale voltage to the input for the duration of the calibration. 3. the calibration is initiated following the write to the mode register. the user then needs to determine when the calibra- tion is complete. this can be performed in two ways, by polling the rdy pin or flag or by monitoring the md2, md1, md0 bits in the mode register. these bits are reset to 0, 0, 1 when the calibration is complete. the flowchart uses polling of the mode bits in the mode register to determine when the calibration is complete. 4. the next step is to perform the full-scale calibration. full-scale calibration can be a self-calibration or system calibration. using system calibration the user must supply the full-scale signal to the analog inputs for the duration of the calibration. again the md2, md1, md0 bits in the mode register are monitored to determine when the calibration is complete. figure 18 shows a flowchart detailing the necessary program- ming steps required to cycle through and read data results from all channels in a multiplexed application. this flowchart assumes that all channels have been previously calibrated. the following are the general programming steps required when reading all channels in a multiplexed application. 1. the ad7708/AD7718 is put into continuous conversion mode. in this mode the part continually converts on the specified channel and the rdy line indicates when valid data is available to be read from the data register. 2. the adccon register is written to select the channel for conversion, its input range and operation is unipolar/ bipolar mode. 3. in this flowchart hardware polling of the rdy line is per- formed to determine when it is valid to read data from the converter. when rdy is low, valid data is available in the data register. the rdy line is set high on a channel change and will not go low until a new valid data word is available. alternatively, the rdy bit in the status register can be polled in software to determine when to read data from the converter. 4. when the data is read, increment the channel address pointer to select the next channel, poll the rdy pin, or rdy bit in the status register, and again read the data. continue until all channels have been read. poll rdy pin write to adccon selecting channel n and its operating range end write to communications register setting up next operation to be a read of data register and then read data result write to mode register selecting continuous conversion mode cycle through and read all channels rdy low? no yes all channels read no yes increment channel address (n = n+1) figure 18. multichannel read operation rev. 0 C34C ad7708/AD7718 digital interface as previously outlined, the ad7708/AD7718s programmable functions are controlled using a set of on-chip registers. data is written to these registers via the parts serial interface and read access to the on-chip registers is also provided by this interface. all communications to the part must start with a write operation to the communications register. after power-on or reset , the device expects a write to its communications register. the data written to this register determines whether the next operation to the part is a read or a write operation and also determines to which register this read or write operation occurs. therefore, write access to any of the other registers on the part starts with a write operation to the communications register followed by a write to the selected register. a read operation from any other register on the part (including the output data register) starts with a write operation to the communications register followed by a read operation from the selected register. the ad7708/AD7718s serial interface consists of five signals, cs , sclk, din, dout and rdy . the din line is used for transferring data into the on-chip registers while the dout line is used for accessing data from the on-chip registers. sclk is the serial clock input for the device and all data transfers (either on din or dout) take place with respect to this sclk signal. the rdy line is used as a status signal to indicate when data is ready to be read from the devicess data register. rdy goes low when a new data word is available in the output register. it is reset high when a read operation from the data register is complete. it also goes high prior to the updating of the output register to indicate when not to read from the device to ensure that a data read is not attempted while the register is being updated. cs is used to select the device. it can be used to decode these devices in systems where a number of parts are connected to the serial bus. figures 2 and 3 show timing diagrams for interfacing to the ad7708/AD7718 with cs used to decode the part. figure 3 is for a read operation from the ad7708/AD7718 output shift register while figure 2 shows a write operation to the input shift register. it is possible to read the same data twice from the out- put register even though the rdy line returns high after the first read operation. care must be taken, however, to ensure that the read operations have been completed before the next output update is about to take place. the serial interface can operate in three-wire mode by tying the cs input low. in this case, the sclk, din and dout lines are used to communicate with the device and the status of the rdy bit can be obtained by interrogating the status regis- ter. this scheme is suitable for interfacing to microcontrollers. if cs is required as a decoding signal, it can be generated from a port bit. for microcontroller interfaces, it is recommended that the sclk idles high between data transfers. the ad7708/AD7718 can also be operated with cs used as a frame synchronization signal. this scheme is suitable for dsp interfaces. in this case, the first bit (msb) is effectively clocked out by cs since cs would normally occur after the falling edge of sclk in dsps. the sclk can continue to run between data transfers provided the timing numbers are obeyed. the serial interface can be reset by exercising the reset input on the part. it can also be reset by writing a series of 1s on the din input. if a logic 1 is written to the ad7708/AD7718 din line for at least 32 serial clock cycles, the serial interface is reset. this ensures that in three-wire systems, if the interface is lost either via a software error or by some glitch in the system, it can be reset back to a known state. this state returns the inter face to where the adc is expecting a write operation to its commu- nications register. this operation resets the contents of all registers to their power-on-reset values. some microprocessor or microcontroller serial interfaces have a single serial data line. in this case, it is possible to connect the adcs dout and din lines together and connect them to the single data line of the processor. a 10 k ? pull-up resistor should be used on this single data line. in this case, if the i nterface is lost, because the read and write operations share the same line, the procedure to reset it back to a known state is somewhat different than previously described. it requires a read operation of 24 serial clocks followed by a write operation wh ere a logic 1 is written for at least 32 serial clock cycles to ensure that the serial interface is back into a known state. microcomputer/microprocessor interfacing the flexible serial interface allows for easy interface to most microcomputers and microprocessors. the flowcharts of figures 16, 17, and 18 outline the sequence that should be followed when i nterfacing a microcontroller or microprocessor to the ad7708/AD7718. figures 19, 20, and 21 show some typical interface circuits. the serial interface on the ad7708/AD7718 is capable of oper- ating from just three wires and is compatible with spi interface protocols. the three-wire operation makes the part ideal for isolated systems where minimizing the number of interface lines minimizes the number of opto-isolators required in the system. the serial clock input is a schmitt-triggered input to accommo- date slow edges from optocouplers. the rise and fall times of other digital inputs to the ad7708/AD7718 should be no slower than 1 s. most of the registers on the ad7708/AD7718 are 8-bit regis- ters, which facilitates easy interfacing to the 8-bit serial ports of microcontrollers. the data register on the AD7718 is 24 bits wide, the adc data register on the ad7708 is 16 bits wide, and the offset and gain registers are 16-bit registers on the ad7708 and 24-bit registers on the AD7718; however, data transfers to these registers can consist of multiple 8-bit transfers to the serial port of the microcontroller. dsp processors and microproces- sors generally transfer 16 bits of data in a serial data operation. some of these processors, such as the adsp-2105, have the facility to program the amount of cycles in a serial transfer. this allows the user to tailor the number of bits in any transfer to match the register length of the required register in the ad7708/ AD7718. even though some of the registers on the ad7708/AD7718 are only eight bits in length, communicating with two of these regis ters in successive write operations can be handled as a single 16-bit data transfer if required. for example, if the filter register is to be updated, the processor must first write to the communications register (saying that the next operation is a write to the filter register) and then write eight bits to the f ilter register. if required, this can all be done in a single 16-bit transfer because once the eight serial clocks of the write opera- tion to the communications register have been completed, the part immediately sets itself up for a write operation to the filter register. rev. 0 ad7708/AD7718 C35C ad7708/AD7718 to 68hc11 interface figure 19 shows an interface between the ad7708/AD7718 and the 68hc11 microcontroller. the diagram shows the minimum (3-wire) interface with cs on the ad7708/AD7718 hardwired low. in this scheme, the rdy bit of the status register is monitored to determine when the data register is updated. an alternative scheme, which increases the number of inter- face lines to four, is to monitor the rdy output line from the ad7708/AD7718. the monitoring of the rdy line can be done in two ways. first, rdy can be connected to one of the 68hc11s port bits (such as pc0), which is configured as an input. this port bit is then polled to determine the status of rdy . the second scheme is to use an interrupt driven system, in which case the rdy output is connected to the irq input of the 68hc11. for interfaces that require control of the cs input on the ad7708/AD7718, one of the port bits of the 68hc11 (such as pc1), which is configured as an output, can be used to drive the cs input. 68hc11 v dd ss sck miso mosi reset sclk cs din dout v dd ad7708/ AD7718 figure 19. ad7708/AD7718-to-68hc11 interface the 68hc11 is configured in the master mode with its cpol bit set to a logic 1 and its cpha bit set to a logic 1. when the 68hc11 is configured like this, its sclk line idles high between data transfers. the ad7708/AD7718 is not capable of full duplex operation. if the ad7708/AD7718 is configured for a write operation, no data appears on the dout lines even when the sclk input is active. similarly, if the ad7708/AD7718 is config- ured for a read operation, data presented to the part on the din line is ignored even when sclk is active. ad7708/AD7718-to-8051 interface an interface circuit between the ad7708/AD7718 and the 8xc51 microcontroller is shown in figure 20. the diagram shows the minimum number of interface connections with cs on the ad7708/AD7718 hardwired low. in the case of the 8xc51 interface the minimum number of interconnects is just two. in this scheme, the rdy bit of the status register is monitored to determine when the data register is updated. the alternative scheme, which increases the number of interface lines to three, is to monitor the rdy output line from the ad7708/AD7718. the monitoring of the rdy line can be done in two ways. first, rdy can be connected to one of the 8xc51s port bits (such as p1.0) which is configured as an input. this port bit is then polled to determine the status of rdy . the second scheme is to use an interrupt-driven system, in which case the rdy output is connected to the int1 input of the 8xc51. for interfaces that require control of the cs input on the ad7708/AD7718, one of the port bits of the 8xc51 (such as p1.1), which is configured as an output, can be used to drive the cs input. the 8xc51 is configured in its mode 0 serial interface mode. its serial interface contains a single data line. as a result, the dout and din pins of the ad7708/AD7718 should be connected together with a 10 k ? pull-up resistor. the serial clock on the 8xc51 idles high between data transfers. the 8xc51 outputs the lsb first in a write operation, while the ad7708/AD7718 expects the msb first so the data to be trans- mitted has to be rearranged before being written to the output serial register. similarly, the ad7708/AD7718 outputs the msb first during a read operation while the 8xc51 expects the lsb first. therefore, the data read into the serial buffer needs to be rearranged before the correct data word from the ad7708/ AD7718 is available in the accumulator. dv dd 8xc51 ad7708/ AD7718 p3.0 p3.1 reset sclk cs din dout dv dd 10k figure 20. ad7708/AD7718-to-8xc51 interface rev. 0 C36C ad7708/AD7718 ad7708/AD7718-to-adsp-2103/adsp-2105 interface figure 21 shows an interface between the ad7708/AD7718 and the adsp-2103/adsp-2105 dsp processor. in the interface shown, the rdy bit of the status register is again monitored to determine when the data register is updated. the alternative scheme is to use an interrupt-driven system, in which case the rdy output is connected to the irq2 input of the adsp-2103/ adsp-2105. the serial interface of the adsp-2103/adsp-2105 is set up for alternate framing mode. the rfs and tfs pins of the adsp-2103/adsp-2105 are configured as active low outputs and the adsp-2103/adsp-2105 serial clock line, sclk, is also configured as an output. the cs for the ad7708/AD7718 is active when either the rfs or tfs outputs from the adsp-2103/ adsp-2105 are active. the serial clock rate on the adsp- 2103/adsp-2105 should be limited to 3 mhz to ensure correct operation with the ad7708/AD7718. din reset dv dd cs ad7708/ AD7718 sclk dout sclk dt dr rfs tfs adsp-2103 / adsp-2105 figure 21. ad7708/AD7718-to-adsp-2103/adsp-2105 interface basic configuration the basic connection diagram for the ad7708/AD7718 in 10- channel mode is shown in figure 22. this shows both the av dd and dv dd pins of the converters being driven from the analog 5 v supply. some applications will have av dd and dv dd driven from separate supplies. av dd and dv dd can be operated inde- pendently of each other, allowing the device to be operated with 5 v analog supply and 3 v digital supply or vice versa. the parts can be operated in 8- or 10-channel configurations. in 8-channel mode the user has two reference input options. this allows the user to operate some channels in ratiometric mode and others in absolute measurement mode. in 10-channel mode only one reference option is available. an ad780/ref195, precision 2.5 v reference, provides the reference source for the part. a quartz crystal or ceramic resonator provides the 32.768 khz master clock source for the part. in some cases, it will be necessary to connect capacitors on the crystal or resonator to ensure that it does not oscillate at overtones of its fundamental operating fre- quency. the values of capacitors will vary, depending on the manufacturers specifications. ad780 / ref195 receive (read) p1 p2 ain6 ain5 ain4 ain3 ain2 ain1 0.1 f 10 f analog 5v supply gnd v in v out agnd dgnd 0.1 f 10 f 0.1 f av dd dv dd ref1in(+) ref1in( ) reset cs dout din sclk mclkin mclkout 5v chip select serial data (write) serial clock 32khz crystal analog 5v supply ad7708/ AD7718 ain8 ain7 ain9 aincom ain10 figure 22. basic configuration for 10-channel mode rev. 0 ad7708/AD7718 C37C analog input channels the input multiplexer on ad7708/AD7718 can be configured as either an 8- or 10-input channel device. this configuration is selected using the chcon bit in the mode register. with chcon = 0 (figure 23), the user has eight input channels; these can be configured as eight pseudo-differential input channels with respect to aincom or four fully-differential input channels. in this configuration the user can select refin1 or refin 2 as the reference for the selected channel using the refsel bit in the mode register. ain6 ain5 ain4 ain3 ain2 ain1 ad7708/ AD7718 ain8 ain7 refin1(+) aincom refin1( ) refin2(+) refin2( ) ain6 ain5 ain4 ain3 ain2 ain1 ain8 ain7 refin1(+) aincom refin1( ) refin2(+) refin2( ) figure 23. analog input and reference options with chcon = 0 with chcon = 1 (figure 24), the user has 10 input channels that can be configured as 10 pseudo-differential input channels with respect to aincom or as five fully-differential input chan- nels. the contents of the chcon bit overrides the refsel bit. if the adc is configured in five fully-differential or 10 pseudo- differential input channel mode, the refsel bit setting is irrelevant as only refin1 is available. channel selection bits ch3, ch2, chi, and ch0 in the adccon register select the input channel. the input multiplexer switches the selected input channel to the on-chip buffer amplifier and sigma-delta converter. when the analog input channel is switched, the settling time of the part must elapse before a new valid word is available from the adc. if any two inputs are configured as a differential input pair, this input is buffered and the common-mode and absolute input volt- age is restricted to a range between agnd + 100 mv and av dd C 100 mv. care must be taken in setting up the common-mode voltage and input voltage range to ensure that these limits are not exceeded, otherwise there will be a degradation in linearity and noise performance. ain6 ain5 ain4 ain3 ain2 ain1 ad7708/ AD7718 ain8 ain7 refin1(+) aincom refin1( ) ain9 ain10 ain6 ain5 ain4 ain3 ain2 ain1 ain8 ain7 refin1(+) aincom refin1( ) ain9 ain10 figure 24. analog input and reference options with chcon = 1 single-ended operation the negbuf bit in the mode register is used to control the operation of the input buffer on the aincom pin when config- ured for pseudo-differential mode of operation. if cleared, the analog negative input (aincom) is unbuffered. it should be noted that the unbuffered input path on the aincom provides a dynamic load to the driving source. therefore, resistor/capacitor combinations on this input pin can cause dc gain errors depend- ing on the output impedance of the source that is driving the aincom input. aincom is tied to agnd for single-ended operation. this enables all pseudo-differential inputs to act as single-ended analog inputs. all analog inputs still operate in buffered mode and their common-mode and absolute input voltage is restricted to a range between agnd + 100 mv and av dd C 100 mv. chop mode of operation ( chop = 0) the signal chain on the ad7708/AD7718 can be operated with chopping enabled or disabled. chopping is enabled or disabled using the chop bit in the mode register. the default mode of operation is for chop enabled ( chop = 0). optimum perfor- mance in terms of minimizing offset error and offset and gain drift performance is achieved when chopping is enabled. the digital filter decimation rate, and consequently the output data rate, is programmable via the sf word loaded to the filter register. output data rates vary from 5.35 hz (186.77 ms) to 105.03 hz (9.52 ms). the output data rate f f sf adc mod = 24 . the overall frequency response from the digital filter with chop- ping enabled is the product of a sinc 3 and a sinc response. there are sinc 3 notches at integer multiples of 3 f adc and there are sinc notches at odd integer multiples of f adc /2. normal mode rejection is the major function of the digital filter on the ad7708/ AD7718. the normal mode 50 1 hz rejection with an sf word of 82 is typically C100 db. the 60 1 hz rejection with sf = 68 is typically C100 db. simultaneous 50 hz and 60 hz rejec tion of better than 60 db is achieved with an sf of 69 and gi ves a data update rate of 19.8 hz and a channel settling time of 101 ms. the ad7708/AD7718 are factory-calibrated so field calibration will only be required if the adc is operated at temperatures that differ substantially from the factory-calibration conditions. rev. 0 C38C ad7708/AD7718 nonchop mode of operation ( chop = 1) chopping is enabled and disabled using the chop bit in the mode register. chopping is disabled by loading a 1 to the chop bit in the mode register. with chopping disabled the available output rates vary from 16.06 hz (62.26 ms) to 1365.33 hz (0.73 ms). the range of applicable sf words is from 3 to 255. when the chopping is disabled the channel output data rate is increased by a factor of 3 compared to the situation when chopping is enabled and using the same sf word. when used in multi plexed applications, operation with chop d isabled will offer the best throughput time when cycling through all channels. the draw back with chop disabled is that the drift performance is degraded and calibration is r equired following a gain change or significant temperature change. the output update and filter decimation rate is again controlled by the sf word loaded to the filter register. the digital filter frequency response places sinc 3 notches at integer multiples of the update rate. the output update rate f f sf adc mod = 8 . the ad7708/AD7718 are tar geted at multiplexed applications and therefore operating with chop disabled optimizes channel throughput time. one of the key requirements in these applicat ions is the selection of an sf word so as to obtain the maximum filter rejection at 50 hz and 60 hz while minimizing the channel throughput rate. this is achieved with an sf word of 75 giving 57 db rejection at 50 hz, and 60 db rejection at 60 hz while offering a channel throughput time of 55 ms. using a higher sf word of 151, 50 hz and 60 hz rejection can be maximized at 60 db w ith a channel throughput rate of 110 ms. an sf word of 255 gives maximum rejection at both 50 hz and 60 hz but the channel throughput rate is restricted to 186 ms. table xxi shows a quick comparison of normal mode 50 hz and 60 hz rejection, settling time, and update rate for a selection of sf words with chop both enabled and disabled. programmable gain amplifier the output from the buffer is applied to the input of the program- mable gain amplifier (pga). the pga gain range is programmed via the range bits in the adccon register. the pga has eight ranges. with an external 2.5 v reference applied, and a pga setting of 128, the unipolar analog input range is 0 mv to 20 mv, while the bipolar analog input range is 20 mv. with a pga setting of 1, the unipolar and bipolar input ranges are 2.56 v. when operating with chop mode enabled ( chop = 0), the adc range-matching specification of 2 v (typ) across all ranges means that calibration need only be carried out on a single range and does not have to be repeated when the pga range is changed. this is a significant advantage when compared with similar adcs available on the market. typical matching across ranges is shown in figure 25. here, the adc is configured in fully-differential, bipolar mode with an external 2.5 v reference, while an analog input voltage of just greater than 19 mv is forced on its analog inputs. the adc continuously converts the dc voltage at an update rate of 5.35 hz, i.e., sf = ffhex, 800 conversion results in total are gathered. the first 100 results are gathered with the adc operating with a pga setting of 128. 19.367 100 0 200 400 300 19.371 19.370 19.369 19.368 19.372 adc input voltage mv 500 19.366 19.365 19.364 600 700 800 sample count adc range 20mv 40mv 80mv 160mv 320mv 640mv 1.28v 2.56v figure 25. adc range matching the pga setting is then switched to 64 and 100 more results are gathered, and so on until the last 100 samples are gathered with a pga setting of 1. from figure 25, the variation in the sample mean through each range, i.e., the range matching, is seen to be of the order of 2 v. when operating with chop mode disabled ( chop = 1), new calibration data is needed (but not necessarily a new calibration) to remove offset error when switching chann els. bipolar/unipolar configuration the analog inputs on the ad7708/AD7718 can accept either unipolar or bipolar input voltage ranges. bipolar input ranges does not imply that the part can handle negative voltages with respect to system agnd. signals in pseudo-differential mode are referenced to aincom, while in fully differential mode they are referenced to the negative input of the differential inp ut. for example, if aincom is 2.5 v and the ad7708/AD7718 ain1 analog input is configured for an analog input range of 0 mv to +20 mv, the input voltage range on the ain1 input is 2.5 v to 2.52 v. if aincom is 2.5 v and the ad7708/AD7718 is con- figured for an analog input range of 1.28 v, the analog input range on the ain1 input is 1.22 v to 3.78 v (i.e., 2.5 v 1.28 v). bipolar or unipolar options are chosen by program ming u/ b bit in the adccon register. programming for either unipolar or bipolar operation does not change any of the input signal conditioning; it simply changes the data output coding and the points on the transfer function where calibrations occur. data output coding when the AD7718 is configured for unipolar operation, the out- put coding is natural (straight) binary with a zero differential input voltage resulting in a code of 000 . . . 000, a midscale voltage resulting in a code of 100 . . . 000, and a full-scale input voltage resulting in a code of 111 . . . 111. the output code for any analog input voltage can be represented as follows: code = ( ain gain 2 24 )/(1.024 v re f ) where ain is the analog input voltage, gain is the pga gain, i.e., 1 on the 2.5 v range and 128 on the 20 mv range. rev. 0 ad7708/AD7718 C39C the output code for any analog input voltage on the ad7708 can be represented as follows: code = ( ain gain 2 16 )/(1.024 v ref ) where ain is the analog input voltage, gain is the pga gain, i.e., 1 on the 2.5 v range and 128 on the 20 mv range. when an adc is configured for bipolar operation, the coding is offset binary with a negative full-scale voltage resulting in a code of 000 . . . 000, a zero differential voltage resulting in a code of 100 . . . 000, and a positive full-scale voltage resulting in a code of 111 . . . 111. the output code from the AD7718 for any analog input voltage can be represented as follows: code = 2 23 [( ain gain/ (1.024 v ref )) + 1] where ain is the analog input voltage, gain is the pga gain, i.e., 1 on the 2.5 v range and 128 on the 20 mv range. the output code from the ad7708 for any analog input voltage can be represented as follows: code = 2 15 [( ain gain /(1.024 v ref )) + 1] where ain is the analog input voltage, gain is the pga gain, i.e., 1 on the 2.5 v range and 128 on the 20 mv range. oscillator circuit the ad7708/AD7718 is intended for use with a 32.768 khz watch crystal or ceramic resonator. a pll internally locks onto a multiple of this frequency to provide a stable 4.194304 mhz clock for the adc. the modulator sample rate is the same as the oscillator frequency. the start-up time associated with 32 khz crystals is typically 300 ms. the ospd bit in the mode register can be used to prevent the oscillator from powering down when the ad7708/ AD7718 is placed in power-down mode. this avoids having to wait 300 ms after exiting power-down to start a conversion at the expense of raising the power-down current. reference input the ad7708/AD7718 has a fully differential reference input capability. when the ad7708/AD7718 is configured in 8-channel mode (chcon = 0) the user has the option of selecting one of two reference options. this allows the user to configure some channels, for example, for ratiometric operation while others can be configured for absolute value measurements. the refsel bit in the mode register allows selection of the required reference. if the refsel bit is cleared , the reference selected is refin1(+) Crefin1(C) for the active channel. if this bit is set , the refer- ence selected is refin2(+) C refin2(C) for the active channel. when the ad7708/AD7718 is configured in 10-channel mode (chcon = 1) the user has only one reference option (refin1). the contents of the chcon bit overrides the refsel bit. if the adc is configured in five fully-differential or 10 pseudo- differential input channel mode, the refsel bit setting is irrelevant as only one reference input is available. the common-mode range for these differential inputs is from agnd to av dd . the reference inputs are unbuffered and therefore excessive r-c source impedances will introduce gain errors. the nominal reference voltage for specified operation, vref, (refin1(+)Crefin1(C) or refin2(+)Crefin2(C)), is 2.5 v, but the ad7708/AD7718 is functional with reference voltages from 1 v to av dd . in applications where the excitation (voltage or current) for the transducer on the analog input also drives the reference voltage for the part, the effect of the low frequency noise in the excitation source will be removed as the application is ratiometric. if the ad7708/AD7718 is used in a nonratiometric application, a low noise reference should be used. recommended reference voltage sources for the ad7708/ AD7718 include the ad780, ref43, and ref192. it should also be noted that the reference inputs provide a high impedance, dynamic load. because the input impedance of each reference input is dynamic, resistor/capacitor combinations on these inputs can cause dc gain errors, depending on the output impedance of the source that is driving the reference inputs. reference voltage sources, like those recommended above (e.g., ad780) will typically have low output impedances and are therefore tolerant of having decoupling capacitors on the refin(+) without introducing gain errors in the system. deriving the reference input voltage across an external resistor will mean that the reference input sees a significant external source impedance. external decoupling on the refin(+) and refin(C) pins w ould not be recommended in this type configuration. reset input the reset input on the ad7708/AD7718 resets all the logic, the d igital filter and the analog modulator while all on-chip registers are reset to their default state. rdy is driven high and the ad7708/AD7718 ignores all communications to any of its registers while the reset input is low. when the reset input returns high the ad7708/AD7718 operates with its default setup conditions and it is necessary to set up all registers and ca rry out a system calibration if required after a reset command. power-down mode loading 0, 0, 0 to the md2, md1, md0 bits in the adc mode register places the adc in device power-down mode. device power-down mode is the default condition for the ad7708/ AD7718 on power-up. the adc retains the contents of all its on-chip registers (including the data register) while in power- down. the device power-down mode does not affect the digital interface, but does affect the status of the rdy pin. writing the ad7708/AD7718 into power-down will reset the rdy line high. placing the part in power-down mode reduces the total current (ai dd + di dd ) to 31 a max when the p art is operated at 5 v and the oscillator allowed to run during pow er-down mode. with the oscillator shut down the total i dd is typically 9 a. rev. 0 C40C ad7708/AD7718 calibration the ad7708/AD7718 provides four calibration modes that can be programmed via the mode bits in the mode register. one of the major benefits of the ad7708/AD7718 is that it is factory- calibrated with chopping enabled as part of the final test process with the generated coefficients stored within the adc. at power- on, the factory gain calibration coefficients are automatically loaded to the gain calibration registers on the ad7708/AD7718. this gives excellent offset and drift performance and it is envisaged that in the majority of applications the user will not need to perform any field calibrations. also, because factory gain calibration coefficients (generated at 25 c ambient) are automatically present at power-on, an internal full-scale calibration will only be required if the part is being operated at temperatures significantly different from 25 c. when chopping is disabled ( chop =1) the ad7708/AD7718 requires an offset calibration or new calibration coefficients on range changing or when significant temperature changes occur as the signal chain is no longer chopped and offset and drift errors are no longer removed as part of the conversion process. the factory-calibration values for any one channel will be over- written if any one of the four calibration options is initiated. the ad7708/AD7718 offers internal or system calibration facilities. for full calibration to occur, the calibration logic must record the modulator output for two different input c onditions. these are zero-scale and full-scale points. th ese points are derived by performing a conversion on the different input voltages provided to the input of the modulator during calibration. the result of the zero-scale calibration conversion is stored in the offset calibration registers for the appropriate channel. the result of the full-scale calibration conversion is stored in the gain calibration registers. with these readings, the calibration logic can calculate the offset and the gain slope for the input-to-output transfer function of the converter. during an internal zero-scale or full-scale calibra tion, the respective zero input and full-scale input are automatically con nected to the adc input pins internally to the device. a system cali- bration, however, expects the system zero-scale and system full-scale voltages to be applied to the external adc pins before the calibration mode is initiated. in this way external adc errors are taken into account and minimized as a result of system calibration. it should also be noted that to optimize calibration accuracy, all ad7708/AD7718 adc calibrations are carried out automatically at the slowest update rate with chop enabled. when chop mode is disabled calibrations are carried out at the update rate defined by the sf word in the filter register. internally in the ad7708/AD7718, the coefficients are normal ized before being used to scale the words coming out of the digital filter. the offset calibration coefficient is subtracted from the result prior to the multiplication by the gain coefficient. with chopping disabled ad7708/AD7718 adc specifications will only apply after a zero-scale calibration at the operating point of interest. from an operational point of view, a calibration should be treated like another adc conversion. a zero-scale calibration (if required) should always be carried out before a full-scale cali bration. system software should m onitor the rdy bit in the status register to determine end of calibration via a polling sequence or interrupt driven routine. grounding and layout since the analog inputs and reference inputs are differential, most of the voltages in the analog modulator are common-mode voltages. the excellent common-mode rejection of the part will remove common-mode noise on these inputs. the analog and digital supplies to the ad7708/AD7718 are independent and separately pinned out to minimize coupling between the analog and digital sections of the device. the ad7708/AD7718 can be operated with 5 v analog and 3 v digital supplies or vice versa. the digital filter will provide rejection of broadband noise on the power supplies, except at integer multiples of the modulator sampling frequency. the digital filter also removes noise from the analog and reference inputs provided these noise sources do not saturate the analog modulator. as a result, the ad7708/ AD7718 is more immune to noise interference than a conventional high-resolution converter. however, because the resolution of the ad7708/AD7718 is so high and the noise levels from the converter so low, care must be taken with regard to grounding and layout. the printed circuit board that houses the adc should be designed so the analog and digital sections are separated and confined to certain areas of the board. this facilitates the use of ground planes that can be easily separated. a minimum etch technique is generally best for ground planes as it gives the best shielding. although the ad7708/AD7718 has separate pins for analog and digital ground, the agnd and dgnd pins are tied together internally via the substrate. therefore, the user must not tie these two pins to separate ground planes unless the ground planes are connected together near the ad7708/AD7718. in systems where the agnd and dgnd are connected some- where else in the system, i.e., the systems power supply, they should not be connected again at the ad7708/AD7718 or a ground loop will result. in these situations it is recommended that ground pins of the ad7708/AD7718 be tied to the agnd plane. in any layout it is implicit that the user keep in mind the flow of currents in the system, ensuring that the paths for all currents are as close as possible to the paths the currents took to reach their destinations. avoid forcing digital currents to flow through the agnd. avoid running digital lines under the device as these will couple noise onto the die. the analog ground plane should be allowed to run under the ad7708/AD7718 to prevent noise coupling. the power supply lines to the ad7708/AD7718 should use as wide a trace as possible to provide low impedance paths and reduce the effects of glitches on the power supply line. fast switching signals like clocks should be shielded with digital ground to avoid radiating noise to other sections of the board and clock signals should never be run near the analog inputs. avoid crossover of digital and analog signals. traces on opposite sides of the board should run at right angles to each other. this will reduce the effects of feedthrough through the board. a microstrip technique is by far the best, but is not always possible with a double-sided board. in this technique, the component side of the board is dedicated to ground planes while signals are placed on the solder side. rev. 0 ad7708/AD7718 C41C good decoupling is important when using high resolution adcs. all analog supplies should be decoupled with 10 f tantalum in parallel with 0.1 f capacitors to agnd. to achieve the best from these decoupling components, they have to be placed as close as possible to the device, ideally right up against the device. all logic chips should be decoupled with 0.1 f ceramic capacitors to dgnd. in systems where a common supply voltage is used to drive both the av dd and dv dd of the ad7708/ AD7718, it is recommended that the systems av dd supply is used. this supply should have the recommended analog supply decoupling capacitors between the av dd pin of the ad7708/ AD7718 and agnd and the recommended digital supply decoupling capacitor between the dv dd pin of the ad 7708/ AD7718 and dgnd. applications the ad7708/AD7718 provides a low cost, high resolution analog-to-digital function. the ad7708 offers 16-bit resolution while the AD7718 offers 24-bit resolution. the ad7708 and AD7718 are pin and function compatible. the AD7718 allows a direct upgradable path from a 16-bit to a 24-bit system with minimal software and no hardware changes. because the analog- to-digital function is provided by a sigma-delta architecture, it makes the part more immune to noisy environments, thus mak- ing the part ideal for use in sensor measurement and in industrial and process control applications. there are two modes of operation associated with the ad7708/AD7718, chop enabled ( chop = 0) or chop disabled ( chop = 1). with chop enabled the signal chain is chopped and the device is factory-calibrated at final test in this mode. field calibration can be avoided due to the extremely low offset and gain drifts exhibited by the converter in this mode. while operating in this mode gives optimum performance in terms of offset error and offset and gain drift performance, it offers limited throughput when cycling through all channels. with chopping disabled, the signal chain is not chopped and therefore the user needs to ensure that the adc is calibrated on range chan ges and if there is a significant temperature change as the gain and offset drift performance is degraded. the key advantage in using the ad7708/AD7718 with chopping disabled is in channel cycling applications where system through- put is of prime importance. the max conversion rate with chop disabled is 1.36 khz compared with 105 hz with chop enabled. the ad7708/AD7718 also provides a programmable gain ampli- fier, a digital filter, and system calibration options. thus, it provides far more system level functionality than off-the-shelf integrating adcs without the disadvantage of having to sup- ply a high quality integrating capacitor. in addition, using the ad7708/AD7718 in a system allows the system designer to achieve a much higher level of resolution because noise perfor- mance of the ad7708/AD7718 is significantly better than that of integrating adcs. the on-chip pga allows the ad7708/AD7718 to handle an analog input voltage range as low as 10 mv full scale with v ref = 1.25 v. the ad7708/AD7718 can be operated in 8-channel mode with two reference input options or 10-channel mode with one reference input. eight-channel mode allows both ratiometric or absolute measurements to be performed on any channel using the two reference input options. the differential analog inputs of the part allow this analog input range to have an ab solute value anywhere between agnd + 100 mv and av dd C 100 mv. the buffer on the negative analog input can be bypassed allowing the ad7708/AD7718 be operated as eight or ten single- ended input channels. the pga allows the user to connect transducers directly to the input of the ad7708/AD7718. the program- mable gain front end on the ad7708/AD7718 allows the part to handle unipolar analog input ranges from 0 mv to +20 mv to 0 v to +2.5 v and bipolar inputs of 20 mv to 2.5 v. because the part operates from a single supply these bipolar ranges are with respect to a biased-up differential input. data acquisition the ad7708/AD7718, with its different configuration options (five fully-differential input or 10 pseudo-differential input channels with one reference input or four fully-differential input or eight pseudo-differential input channels with two reference inputs), is suited to low bandwidth, high resolution data acquisi- tion systems. in addition, the 3-wire digital interface allows this data acquisition front end to be isolated with just three opto- isolators. the entire system can be operated from a single 3 v or 5 v supply, provided that the input signals to the ad7708/ AD7718s analog inputs are all of positive polarity. 5v ad780 ain6 ain5 ain4 ain3 ain2 ain1 5v gnd v in v out agnd dgnd av dd dv dd ref1in( ) mclkin mclkout 32khz ad7708/ AD7718 ain8 ain7 ain9 aincom ain10 micro- controller sclk cs din dout rdy reset refin1(+) figure 26. data acquisition using the ad7708/AD7718 programmable logic controllers the ad7708/AD7718 is also suited to programmable logic controller applications. in such applications, the adc is required to handle signals from a variety of different transducers. the ad7708/AD7718s programmable gain front end allows the part to either handle low level signals directly from a transducer or full-scale signals that have already been conditioned. the faster throughput rate and settling time of the part when operated with chopping disabled makes this the optimum mode of operation in plc applications as an important feature in these applications is loop response time. the configuration of the ad7708/AD7718 in plc applications is similar to that outlined for a data acquisi- tion system and is shown in figure 26. in this application the ad7708/AD7718 is configured in 10-channel mode, ( chcon = 1) and can be operated as 10 pseudo-differential inputs with respect to aincom or as five fully-differential input channels. rev. 0 C42C ad7708/AD7718 converting single-ended inputs the ad7708/AD7718 generally operates in buffered mode. this places a restriction of agnd + 100 mv to avdd C 100 mv on the absolute and common-mode voltages that can be applied to any input on the ad7708/AD7718. some applications may require the measurement of analog inputs with respect to agnd. to enable the ad7708/AD7718 to be used in these single-ended applications, the buffer on the aincom can be bypassed. the negbuf bit in the mode register controls the operation of the input buffer on the aincom input when a channel is configured for pseudo-differential mode of operation. if cleared , the analog negative input (aincom) is unbuffered, allowing it to be tied to agnd in single-ended input configuration. if this bit is set , the analog negative input (aincom) is buffered, placing a restriction on its common- mode input range. when aincom is unbuffered, signals with a common-mode range from agnd C 30 mv to avdd + 30 mv can be accommodated on this input allowing the end user to connect the aincom input to agnd and perform single- ended m easurements with respect to this input. this unbuffered input path on the aincom provides a dynamic load to the driving source. therefore, resistor/capacitor combinations on this input pin can cause dc gain errors, depending on the output impedance of the source that is driving the aincom input. all analog inputs still operate in buffered mode and their com- mon-mode and absolute input voltage is restricted to a range between agnd + 100 mv and av dd C 100 mv. combined ratiometric and absolute value measurement system the ad7708/AD7718 when operated with chcon = 0 can be configured for operation as four fully-differential analog inputs or eight pseudo-differential analog inputs with two fully-differential reference inputs. having the ability to use either refin1 or refin2 with any channel during the conversion process allows the end user to make both absolute and ratiometric measure- ments as shown in figure 27. in this example a fully-differential analog input (ain1Cain2) is being converted from a bridge trans- ducer in a ratiometric manner using refin1 as the reference input for this channel. ain3 is configured as a pseudo-differential input channel using refin2 to perform an absolute measurement on the potentiometer. the refsel bit in the mode register is used to select which reference is used with the active channel during the conversion process. when the ad7708/AD7718 is configured with chcon = 1, only one reference (refin1) is available. the contents of the chcon bit override the refsel bit. if the adc is configured in five fully-differential or 10 pseudo-differential input channel mode, the refsel bit setting is irrelevant as only refin1 is available. refin1( ) AD7718 refin2(+) refin1(+) aincom ain1 ain3 ain2 refin2( ) gnd excitation voltage = 4v wiper figure 27. absolute and ratiometric measurement system using AD7718 rev. 0 ad7708/AD7718 C43C table xxi. normal mode 50 hz and 60 hz rejection vs. settling time and update rate for a selection of sf words chop disabled chop enabled 50 hz 1 hz 60 hz 1 hz 50 hz 1 hz 60 hz 1 hz sf rejection rejection rejection rejection word f adc (hz) t settle (ms) (db) (db) f adc (hz) t settle (ms) (db) (db) 03 1365.33 2.20 0.05 0.08 n/a n/a n/a n/a 13 315.08 9.52 1 1.5 105.03 19.04 21 13.6 69 59.36 50.54 42 94 19.79 101 60 94 75 54.6 54.93 57 60 18.2 110 62 66 82 49.95 60 100 16.65 180 100 53 151 27.13 110.6 60 60 9.04 221 72 63 255 16.06 186.76 77 68 5.35 373.5 93 68 optimizing throughput while maximizing 50 hz and 60 hz rejection in a multiplexed data acquisition system the ad7708/AD7718 can be optimized for one of two modes of operation. operating the ad7708/AD7718 with chopping enabled ( chop = 0) optimizes the ad7708/AD7718 for analog performance over channel throughput. output data rates vary from 5.35 hz (186.77 ms) to 105.03 hz (9.52 ms). optimum perfor mance, in terms of minimizing offset error and offset and gain drift performance, is achieved as a result of chopp ing the signal chain. with chopping disabled the available output rates vary from 16.06 hz (62.26 ms) to 1365.33 hz (0.73 ms). the range of applicable sf words is from 3 to 255. when the chopping is disabled the channel output data rate is increased by a factor of 3 compared to the situation when chopping is enabled is disabled. when used in multiplexed applications, operation with chop disabled w ill offer the best throughput time when cycling through all channels. the drawback with chopping disabled is that the drift performance is d egraded and calibra- tion is required following gain and temperature changes. one of the key requirements in these applications is to optimize the sf word to obtain the maximum filter rejection at 50 hz and 60 hz while minimizing the channel throughput rate. this is achieved with an sf word of 75 giving 57 db rejection at 50 hz and 60 db rejection at 60 hz while offering a channel throughput time of 55 ms. using a higher sf word of 151, 50 hz and 60 hz rejection can be maximized at 60 db with a channel throughput rate of 110 ms. an sf word of 255 gives maximum rejection at both 50 hz and 60 hz, but the channel throughput rate is restricted to 186 ms. table xxi gives a quick comparison of normal mode 50 hz and 60 hz rejection, settling time, and u pdate rate for a selec- tion of sf words with both chopping enabled and disabled. rev. 0 C44C c01831C1C7/01(0) printed in u.s.a. ad7708/AD7718 28-lead plastic soic (r-28) 0.0125 (0.32) 0.0091 (0.23) 8 0 0.0291 (0.74) 0.0098 (0.25) 45 0.0500 (1.27) 0.0157 (0.40) seating plane 0.0118 (0.30) 0.0040 (0.10) 0.0192 (0.49) 0.0138 (0.35) 0.1043 (2.65) 0.0926 (2.35) 0.0500 (1.27) bsc 28 15 14 1 0.7125 (18.10) 0.6969 (17.70) 0.4193 (10.65) 0.3937 (10.00) 0.2992 (7.60) 0.2914 (7.40) pin 1 28-lead plastic tssop (ru-28) 0.177 (4.50) 0.169 (4.30) 28 15 14 1 0.386 (9.80) 0.378 (9.60) 0.256 (6.50) 0.246 (6.25) pin 1 seating plane 0.006 (0.15) 0.002 (0.05) 0.0118 (0.30) 0.0075 (0.19) 0.0256 (0.65) bsc 0.0433 (1.10) max 0.0079 (0.20) 0.0035 (0.090) 0.028 (0.70) 0.020 (0.50) 8 0 outline dimensions dimensions shown in inches and (mm). |
Price & Availability of AD7718 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |