philips semiconductors product specification three quadrant triacs bta204s series d, e and f guaranteed commutation general description quick reference data passivated guaranteed commutation triacs symbol parameter max. unit in a plastic envelope suitable for surface mounting, intended for use in motor control bta204s - 600d circuits or with other highly inductive loads. bta204s - 600e these devices balance the requirements of bta204s - 600f commutation performance and gate v drm repetitive peak 600 v sensitivity. the "logic level" d series is off-state voltages intended for interfacing with low power i t(rms) rms on-state current 4 a drivers, including micro controllers. i tsm non-repetitive peak 25 a on-state current pinning - sot428 pin configuration symbol pin description 1 mt1 2 mt2 3 gate tab mt2 limiting values limiting values in accordance with the absolute maximum system (iec 134). symbol parameter conditions min. max. unit v drm repetitive peak off-state - 600 1 v voltages i t(rms) rms on-state current full sine wave; t mb 107 ?c - 4 a i tsm non-repetitive peak full sine wave; t j = 25 ?c prior to on-state current surge t = 20 ms t = 16.7 ms - 25 a -27a i 2 ti 2 t for fusing t = 10 ms - 3.1 a 2 s di t /dt repetitive rate of rise of i tm = 6 a; i g = 0.2 a; 100 a/ s on-state current after di g /dt = 0.2 a/ s triggering i gm peak gate current - 2 a p gm peak gate power - 5 w p g(av) average gate power over any 20 ms period - 0.5 w t stg storage temperature -40 150 ?c t j operating junction - 125 ?c temperature 1 2 3 tab t1 t2 g 1 although not recommended, off-state voltages up to 800v may be applied without damage, but the triac may switch to the on-state. the rate of rise of current should not exceed 6 a/ s. may 2003 1 rev 2.000
philips semiconductors product specification three quadrant triacs bta204s series d, e and f guaranteed commutation thermal resistances symbol parameter conditions min. typ. max. unit r th j-mb thermal resistance full cycle - - 3.0 k/w junction to mounting base half cycle - - 3.7 k/w r th j-a thermal resistance pcb (fr4) mounted; footprint as in fig.14 - 75 - k/w junction to ambient static characteristics t j = 25 ?c unless otherwise stated symbol parameter conditions min. typ. max. unit bta204s ...d ...e ...f i gt gate trigger current 2 v d = 12 v; i t = 0.1 a t2+ g+ - - 5 10 25 ma t2+ g- - - 5 10 25 ma t2- g- - - 5 10 25 ma i l latching current v d = 12 v; i gt = 0.1 a t2+ g+ - - 6 12 20 ma t2+ g- - - 9 18 30 ma t2- g- - - 6 12 20 ma i h holding current v d = 12 v; i gt = 0.1 a - - 6 12 20 ma v t on-state voltage i t = 5 a - 1.4 1.7 v v gt gate trigger voltage v d = 12 v; i t = 0.1 a - 0.7 1.5 v v d = 400 v; i t = 0.1 a; 0.25 0.4 - v t j = 125 ?c i d off-state leakage v d = v drm(max) ; t j = 125 ?c - 0.1 0.5 ma current dynamic characteristics t j = 25 ?c unless otherwise stated symbol parameter conditions min. typ. max. unit bta204s ...d ...e ...f dv d /dt critical rate of rise of v dm = 67% v drm(max) ;203050--v/ s off-state voltage t j = 125 ?c; exponential waveform; gate open circuit di com /dt critical rate of change v dm = 400 v; t j = 125 ?c; 1.1 2.1 3.0 - - a/ms of commutating current i t(rms) = 4 a; dv com /dt = 10v/ s; gate open circuit di com /dt critical rate of change v dm = 400 v; t j = 125 ?c; 4.5 8.0 15 - - a/ms of commutating current i t(rms) = 4 a; dv com /dt = 0.1v/ s; gate open circuit t gt gate controlled turn-on i tm = 12 a; v d = v drm(max) ;---2- s time i g = 0.1 a; di g /dt = 5 a/ s 2 device does not trigger in the t2-, g+ quadrant. may 2003 2 rev 2.000
philips semiconductors product specification three quadrant triacs bta204s series d, e and f guaranteed commutation fig.1. maximum on-state dissipation, p tot , versus rms on-state current, i t(rms) , where = conduction angle. fig.2. maximum permissible non-repetitive peak on-state current i tsm , versus pulse width t p , for sinusoidal currents, t p 20ms. fig.3. maximum permissible non-repetitive peak on-state current i tsm , versus number of cycles, for sinusoidal currents, f = 50 hz. fig.4. maximum permissible rms current i t(rms) , versus mounting base temperature t mb . fig.5. maximum permissible repetitive rms on-state current i t(rms) , versus surge duration, for sinusoidal currents, f = 50 hz; t mb 107?c. fig.6. normalised gate trigger voltage v gt (t j )/ v gt (25?c), versus junction temperature t j . 012345 0 1 2 3 4 5 6 7 8 = 180 120 90 60 30 it(rms) / a ptot / w tmb(max) / c 125 122 119 116 113 110 107 104 101 1 -50 0 50 100 150 0 1 2 3 4 5 tmb / c it(rms) / a 107 c 10us 100us 1ms 10ms 100ms 10 100 1000 t / s itsm / a t i tsm time i tj initial = 25 c max t di /dt limit t t2- g+ quadrant 0.01 0.1 1 10 0 2 4 6 8 10 12 surge duration / s it(rms) / a 1 10 100 1000 0 5 10 15 20 25 30 bt136 number of cycles at 50hz itsm / a t i tsm time i tj initial = 25 c max t -50 0 50 100 150 0.4 0.6 0.8 1 1.2 1.4 1.6 tj / c vgt(tj) vgt(25 c) may 2003 3 rev 2.000
philips semiconductors product specification three quadrant triacs bta204s series d, e and f guaranteed commutation fig.7. normalised gate trigger current i gt (t j )/ i gt (25?c), versus junction temperature t j . fig.8. normalised latching current i l (t j )/ i l (25?c), versus junction temperature t j . fig.9. normalised holding current i h (t j )/ i h (25?c), versus junction temperature t j . fig.10. typical and maximum on-state characteristic. fig.11. transient thermal impedance z th j-mb , versus pulse width t p . -50 0 50 100 150 0 0.5 1 1.5 2 2.5 3 tj / c t2+ g+ t2+ g- t2- g- igt(tj) igt(25 c) 0 0.5 1 1.5 2 2.5 3 0 2 4 6 8 10 12 vt / v it / a tj = 125 c tj = 25 c typ max vo = 1.27 v rs = 0.091 ohms -50 0 50 100 150 0 0.5 1 1.5 2 2.5 3 tj / c il(tj) il(25 c) 10us 0.1ms 1ms 10ms 0.1s 1s 10s 0.01 0.1 1 10 tp / s zth j-mb (k/w) unidirectional bidirectional t p p t d -50 0 50 100 150 0 0.5 1 1.5 2 2.5 3 tj / c ih(tj) ih(25c) may 2003 4 rev 2.000
philips semiconductors product specification three quadrant triacs bta204s series d, e and f guaranteed commutation mechanical data dimensions in mm net mass: 1.1 g fig.12. sot428 : centre pin connected to tab. mounting instructions dimensions in mm fig.13. sot428 : minimum pad sizes for surface mounting . notes 1. plastic meets ul94 v0 at 1/8". 6.22 max 2.38 max 0.93 max 6.73 max 0.3 10.4 max 0.5 0.8 max (x2) 2.285 (x2) 0.5 seating plane 1.1 0.5 min 5.4 4 min 4.6 1 2 3 tab 7.0 7.0 2.15 2.5 4.57 1.5 may 2003 5 rev 2.000
philips semiconductors product specification three quadrant triacs bta204s series d, e and f guaranteed commutation definitions data sheet status data sheet product definitions status 3 status 4 objective data development this data sheet contains data from the objective specification for product development. philips semiconductors reserves the right to change the specification in any manner without notice preliminary data qualification this data sheet contains data from the preliminary specification. supplementary data will be published at a later date. philips semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product product data production this data sheet contains data from the product specification. philips semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. changes will be communicated according to the customer product/process change notification (cpcn) procedure snw-sq-650a limiting values limiting values are given in accordance with the absolute maximum rating system (iec 134). stress above one or more of the limiting values may cause permanent damage to the device. these are stress ratings only and operation of the device at these or at any other conditions above those given in the characteristics sections of this specification is not implied. exposure to limiting values for extended periods may affect device reliability. application information where application information is given, it is advisory and does not form part of the specification. ? philips electronics n.v. 2003 all rights are reserved. reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. the information presented in this document does not form part of any quotation or contract, it is believed to be accurate and reliable and may be changed without notice. no liability will be accepted by the publisher for any consequence of its use. publication thereof does not convey nor imply any license under patent or other industrial or intellectual property rights. life support applications these products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify philips for any damages resulting from such improper use or sale. 3 please consult the most recently issued datasheet before initiating or completing a design. 4 the product status of the device(s) described in this datasheet may have changed since this datasheet was published. the latest information is available on the internet at url http://www.semiconductors.philips.com. may 2003 6 rev 2.000
|
