photocoupler 12-81 high ac input current, ac input type photocoupler ltv-733h series ordering information part number package safety standard approval application part number ltv-733h ltv-733hm ltv-733hs ltv-733hs-ta ltv-733hs-ta1 ltv733h-v ltv733hm-v ltv733hs-v ltv733hsta-v ltv733hsta1-v 6-pin dip 6-pin (leads with 0.4" spacing) 6-pin (lead bends for surface mount) 6-pin (tape and reel packaging of type i) 6-pin (tape and reel packaging of type ii) 6-pin dip 6-pin (leads with 0.4" spacing) 6-pin (lead bends for surface mount) 6-pin (tape and reel packaging of type i) 6-pin (tape and reel packaging of type ii) ul approved nemko approved csa approved demko approved fimko approved semko approved vde approved ltv - 733h ltv - 733h features directly connectable to ttl ac input response high input current( i f : max. 150ma ) high input-output isolation voltage ( viso = 5,000vrms ) low collector dark current ( i ceo : max. 10 -7 a at v ce = 20v ) current transfer ratio ( ctr : min. 20% at i f = 100ma, v ce = 2v ) ul approved ( no. e113898 ) csa approved ( no. ca91533-1 ) fimko approved ( no. 203512 ) nemko approved ( no. p98102534 ) demko approved ( no. 308184 ) semko approved ( no. 9844179/01-02 ) vde approved ( no. 094722 ) options available : - leads with 0.4" (10.16mm) spacing (m type) - lead bends for surface mounting (s type) - tape and reel of type i for smd (add "-ta" suffix) - tape and reel of type ii for smd (add "-ta1" suffix) - vde 0884 approvals (add "-v" suffix) applications 1. telephone sets 2. system appliances, measuring instruments 3. signal transmission between circuits of different poten- tials and impedances package dimensions notes : 1. year date code. 2. 2-digit work week. 3. factory code shall be marked. (z taiwan, y thailand). 4. all dimensions are in millimeters (inches). 5. tolerance is 0.25mm (.010") unless otherwise noted. 6. specifications are subject to change without notice.
12-82 parameter symbol rating unit input output total power dissipation *1. isolation voltage operating temperature s torage temperature *2. soldering temperature forward current power dissipation collector-emitter voltage emitter-collector voltage collector-base voltage emitter-base voltage collector current collector power dissipation i f p v ceo v eco v cbo v ebo i c p c p tot v iso t opr t stg t sol 150 230 35 6 35 6 80 160 320 5,000 -30~+100 -55~+125 260 ma mw v v v v ma mw mw vrms parameter symbol min. typ. max. unit conditions input output transfer characteristics forward voltage reverse current collector dark current emitter-collector breakdown voltage collector current * current transfer ratio collector-emitter saturation voltage isolation resistance floating capacitance cut-off frequency response time (rise) response time (fall) v f c t i ceo bv ceo bv eco i c ctr v ce(sat) r iso c f f c t r t f 35 20 1.4 50 1.7 400 100 v pf na *ctr= 100% i c i f i f = 100ma v=0, f=1khz v ce =20v, i f =0 ratings and characteristics absolute maximum ratings (ta=25 ) *1. ac for 1 minute, r.h. = 40 ~ 60% isolation voltage shall be measured using the following method. (1) short between anode and cathode on the primary side and between collector and emitter on the secondary side. (2) the isolation voltage tester with zero-cross circuit shall be used. (3) the waveform of applied voltage shall be a sine wave. *2. for 10 seconds collector-emitter breakdown voltage 6 20 5 10 10 15 0.1 1 10 11 0.6 80 4 3 80 80 0.2 1 18 18 v v ma % v pf khz s s i c =0.1ma i f =0 i e =10 a i f =0 i f = 100ma v ce =2v i f = 100ma i c =1ma dc500v 40~60%r.h. v=0, f=1mh z v ce =5v, i c =2ma r l =100 , -3db v ce =2v, i c =2ma r l =100 electrical / optical characteristics (ta=25 )
photocoupler 12-83 typical electrical/optical characteristic curves (25 ambient temperature unless otherwise noted)
12-84
|
