View ATSAM3103_2822899.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

6093a?drmsd?25-oct-04 features three dsps and 24-bit audio router on-chip 32 khz to 96 khz sampling rate 16-bit microcontroller on-chip variety of i/os, including smartmedia ? and dataflash ? embedded ram for single chip operation (530 kbit) warm start power-down 1 a typical deep power-down, 0.5 mw/mips typical operating external flash/rom capability available in a 64-lead tqfp package ideal for real-time audio applications ? mp3 decoding wavetable synthesis (gm-lite) ? effect processing (reverb, echo, chorus, etc.) ? speech recognition and synthesis ? filtering, sampling rate conversion typical applications: cellular phones, mp3 player, effect devices, intelligent answering machinces, toys description the ATSAM3103 is a member of the new atsam3000 family that uses dsp array technology. the ATSAM3103 includes three 24-bit dsps, a 24-bit audio router and a general purpose 16-bit on-chip cisc microcontroller. its high performance and flexibil- ity with eight input and eight output channels allow implementation of professional quality audio applications such as effects processing and mp3 decoding. a variety of i/os, including smartmedia ? and dataflash ? are provided. sampling rates up to 96 khz at 24 bits are supported. audio processing ATSAM3103 versatile low-power audio dsp/ low-cost effects dsp
2 ATSAM3103 6093a?drmsd?25-oct-04 dsp array block diagram figure 1. ATSAM3103 dsp array block diagram functional description dsp array the ATSAM3103 includes three on-chip dsps. each dsp (p24) is built around a 2k x 24 ram and a 1k x 24 rom. the ram contains both data and p24 instructions; the rom contains typical coefficients such as fft cosines and windowing. a p24 sends and receives audio samples through the sync bus. it can request external data such as compressed audio through the async bus. each p24 ram can be accessed through the async bus. each p24 is capable of typical mac operation loops, including auto-indexing, bit reverse and butterfly (multiplication of complex numbers). it also includes specialized audio instructions such as state variable iir filtering, envelope generation, linear interpolation and wavetable loop. one p24 is sufficient for processing one channel of mp3, implementing a multi-tap delay line or a multi-tap transversal filter. a single p24 is also capable of generating 12 voices of wavetable sound at 32 khz sampling rate (8 voices at 48 khz), including sample cache, pitch control, second-order filter and two envelope generators. sync bus the sync bus transfers data on a frame basis, typical frame rates being 32, 44.1, 48 or 96 khz. each frame is divided into 64 time slots. each slot is divided into 4 bus cycles. each p24 is assigned a hardwired time slot (8 to 63), during which it may provide 24-bit data to the bus (up to 4 data samples). each p24 can read data on the bus at any time, mmu 16-bit processor (p16) embedded rom 1k x 16 bios and debug embedded ram 16k x 24 i/os timers, uarts, dataflash, ports router final acc mix audio out audio in dsp array (3 p24 dsps) sync bus async bus audio i/o external i/o
3 ATSAM3103 6093a?drmsd?25-oct-04 allowing inter p24 communication at the current sampling rate. slots 0 to 7 are reserved for a specific router dsp, which also handles audio out, audio in, and remix send. async bus the async bus is 24-bit data inside the chip and 16-bit outside. the p16 processor normally masters the async bus; it can read/write the p24 memories and the external or embedded rom/ram. however, each p24 can request a bus mas- ter cycle for accessing external rom/ram or other p24 memories. this allows efficient intercommunication between several p24s on asynchronous block basis. specific p24 instructions float and fix convert fixed-point dsp data to floating-point 16 bits. this allows for 20-bit audio dynamic range when using 16-bit external memory. 16-bit processor the p16 processor is widely used in atsam products. using the p16 allows to keep the large firmware investments from the atsam97xx series. a built-in rom, connected to the p16, holds basic input/output software (bios) for peripherals such as uart, dataflash, smartmedia, mpu, as well as a debugger using a dedicated asynchronous serial line. the firmware can reside on external parallel rom/flash or it can be down- loaded at power-up into the built-in 16k x 24 ram from serial eeprom, dataflash, smartmedia or host. mmu (memory management unit) the mmu handles transfer requests between the external or embedded ram/rom, the p16 and the p24s through the async bus. the ATSAM3103 includes an on-chip 16k x 24 ram. router: final acc, mix, audio out, audio in this block includes a ram, accessed through the async bus, which defines the routing from the sync bus to/from the audio i/o or back to the sync bus (mix send). it takes care of mix and accumulation from sync bus samples. eight channels of audio in and eight channels of audio out are provided (4 stereo in/out, i2s format). the stereo audio in channels may have a different sampling rate than the audio out channels. in this case, one or more p24s take care of sampling rate conversion. i/o the ATSAM3103 includes versatile i/os that share common pins for reduced pin count and small ic footprint. most i/os, when not used for a specific function, remain available as firmware controlled general-purpose pins. the following peripherals are included on-chip: 2 x 8-bit timers 2 x 16-bit timers parallel slave 8-bit port, mpu401 compatible parallel master 8-bit port, for connection to smartmedia and/or lcd display, switches, etc. 2 x asynchronous bi-directional serial ports synchronous serial slave port (spi type host connection) spi master bi-directional port for eeprom or dataflash c onnection firmware controlled i/o pins
4 ATSAM3103 6093a?drmsd?25-oct-04 typical application examples figure 2. host-controlled mp3 player ATSAM3103 firmware download from host (when using parallel interface) choice of host communication interfaces ? 8-bit parallel ? asynchronous serial (1) ? synchronous serial (spi) (1) full mp3 support inculding very low bit rate extension (iso/iec 13813-3) easily upgradeable to other coding standards single cbga on request note: 1. external firmware serial eeprom required figure 3. stand-alone mp3 player (smartmedia based) s/pdif connection possible pc connection possible ATSAM3103 dac rom stereo audio out compressed audio (from host) ATSAM3103 dac stereo audio out 8-mb to 12-mb smart media switches, lcd display midi
5 ATSAM3103 6093a?drmsd?25-oct-04 figure 4. low-cost high-quality effect high quality, full 24-bit multi-effects such as reverb, chorus and compression stereo 10-band graphic equalizer figure 5. intelligent answering machines (dataflash-based) high quality telephone recording at low bit rate (8 kbit/sec) close to one hour recording capacity using 32-mbit dataflash detects touch-tone easy to program figure 6. toys with artificial intelligence speech recognition learning functions adpcm record/play ATSAM3103 adc dac atmel eeprom stereo audio in/out switches lcd display midi ATSAM3103 adc dac atmel dataflash audio in/out switches lcd display ATSAM3103 adc dac atmel eeprom audio in/out switches motor controi
6 ATSAM3103 6093a?drmsd?25-oct-04 dsp capacity and i/o configuration dsp considerations the ATSAM3103 includes three p24 dsps. table 1 lists the performance levels achievable by the p24. the ATSAM3103 runs firmware from built-in 16 x 24 ram. the firmware should be downloaded at power-up. this can be done from the following: a small 256-kbit external eeprom with spi interface such as the atmel at25256 a dataflash (current capacities range from 1 mbit to 64 mbits) if audio storage functions are required a smartmedia card (supported capacities from 8 mbytes to 128 mbytes) parallel mpu type interface i/o selection considerations i/os are organized in groups that can be mutually exclusive because they share the same ic pins (please refer to the pinout to identify the exclusions). the two main types of operation are host controlled and stand-alone. host-controlled operation there are three main possible ways of communication with a host processor: 8-bit parallel mpu type bi-directional interface signals: d7 - d0, cs , wr , rd , a0, irq asynchronous serial, midi_in and, optionally, midi_out synchronous serial signals: sdin, sclk, sync, int the mpu type interface allows downloading firmware to the chip from the host. if another interface is used, then external eeprom or dataflash is required. stand-alone operation possible stand-alone modes are: firmware into external rom or dataflash firmware into external smartmedia. in this case, the firmware should reside in the smartmedia reserved sectors starting at sector #1. table 1. p24 performance levels function p24s required mp3 decode 3 stereo reverb and chorus @48 khz 1 31-band equalizer @96 khz 3 stereo 31-band equalizer @48 khz 3 256 points fft or ifft @96 khz incl. windowing 1
7 ATSAM3103 6093a?drmsd?25-oct-04 pinout pin description identical sharing number indicates multifunction pins. pd indicates a pin with built-in pull-down resistor. pu indicates a pin with built-in pull-up resistor. table 2. pinout by pin name pin name pin number type sharing description gnd 4, 13, 19, 25 , 36, 43, 48, 57 pwr - digital ground. all these pins should be returned to a ground plane vc18 12, 31, 46, 63 pwr - core power. all these pins should be returned to nominal 1.8v or to pwrout if the built-in power switch is used. vc33 3, 32 pwr - periphery power. all these pins should be returned to nominal 3.3v. pwrin 18 pwr - power switch input; should be returned to nominal 1.8v even if the power switch is not used pwrout 17 pwr - power switch output; should be connected to all vc18 pins if the power switch is used d7 - d0 59, 58, 56, 55, 52, 51, 50, 49 i/o 1 slave 8-bit interface data. output if cs and rd are low (read from chip), input if cs and wr are low (write to chip). type of data defined by a0 input. i/o7 - i/o0 59, 58, 56, 55, 52, 51, 50, 49 i/o 1 smartmedia data or other peripheral data p0.7 - p0.0 59, 58, 56, 55, 52, 51, 50, 49 i/o 1 general-purpose i/o; can be programmed individually as input or output clad3 - 0 59, 58, 56, 55 in 1 optional bit clocks for digital audio input. used for sampling rate conversion, for external incoming digital audio such as aes/beu or s/pdif. wsad3 - 0 52, 51, 50, 49 in 1 optional word selects for digital audio input. used for sampling rate conversion, for external incoming digital audio such as aes/beu or s/pdif. a0 60 in 2 slave 8-bit interface address. indicates data/status or data/ctrl transfer type (cs rd low or cs wr low) smpd 60 in 2 smartmedia presence detect p0.10 60 in 2 general-purpose input pin sclk 60 in 2 serial slave synchronous interface input clock cs 64 in 3 slave 8-bit interface chip select, active low p0.11 64 in 3 general-purpose input pin sync 64 in 3 serial slave synchronous interface input sync signal wr 1 in 4 slave 8-bit interface write, active low. d7 - d0 data is sampled by chip on wr rising edge if cs is low smc 1 in 4 smartmedia configuration. this pin is sensed after power-up. if found low, it is assumed that a smartmedia connector is present. the built-in firmware will wait for smartmedia smpd. p0.12 1 in 4 general-purpose input pin rd 2 in 5 slave 8-bit interface read, active low. d7 - d0 data is output when rd goes low and cs is low
8 ATSAM3103 6093a?drmsd?25-oct-04 r|b 2 in 5 smartmedia ready busy/ status p0.13 2 in 5 general-purpose input pin irq 8 out 6 slave 8-bit interface interrupt request. high when data is ready to be transferred from chip to host. reset by a read from host (cs = 0 and rd = 0) smre 8 out 6 smartmedia read enable (re ), active low fs0 8 in 6 freq sense, sensed at power up. together with fs1, allows the firmware to know the operating freq of the chip (see fs1). p0.8 8 i/o 6 general-purpose i/o pin int 8 out 6 serial slave synchronous interface data request, active low midi_in 9 in 7 serial midi in p0.14 9 in 7 general-purpose input pin sdin 9 in 7 serial slave synchronous interface input data midi_out 10 out 8 serial midi out fs1 10 in 8 freq sense, sensed at power up. fs1/fs0 allow firmware to know operating frequency of chip as follows: 00 6.9552 mhz 01 9.6 mhz 10 11.2896 mhz 11 12.288 mhz p0.9 10 i/o 8 general-purpose i/o dabd3 - 0 42, 41, 40, 39 out - four stereo channels of digital audio output, i2s format clbd 6 out - audio bit clock for dabd3 - 0. audio bit clock for daad3 - 0 if the corresponding clad3 - 0 is not used. wsbd 7 out - audio left/right channel select for dabd3 - 0. audio left/right channel for daad3 - 0 if the corresponding wsad3 - 0 is not used. ckout 5 out - external dac/codec master clock. same frequency as x2 pin. can be programmed to be 128 x fs, 192 x fs, 256 x fs, 384 x fs, where fs is the dac/codec sampling rate. daad0 34 in 9 stereo audio data input, i2s format. can operate on clbd master rate or clad0 external rate when sampling rate conversion is requested. p0.15 34 in 9 general-purpose input pin daad3 - 1 38, 37 35 in pd - three additional channels of stereo audio input, i2s format. can individually operate on clbd master rate or corresponding clad3 - 1 when sampling rate conversion is requested. daad3 - 1 have built-in pull-downs. they may be left open if not used. mute 11 i/o 10 external dac/codec mute. sensed at power up. if found high, then mute becomes an active high output. if found low, then mute becomes an active low output. p1.6 11 i/o 10 general-purpose i/o pin smce 29 out 11 smartmedia chip enable (ce ), active low p1.5 29 i/o 11 general-purpose i/o pin smale 28 out 12 smartmedia address latch enable (ale) table 2. pinout by pin name (continued) pin name pin number type sharing description
9 ATSAM3103 6093a?drmsd?25-oct-04 p1.4 28 i/o 12 general-purpose i/o pin smwe 27 out 13 smartmedia write enable (we ), active low p1.3 27 i/o 13 general-purpose i/o pin smcle 26 out 14 smartmedia command latch enable (cle) p1.2 26 i/o 14 general-purpose i/o pin dfcs 14 out - dataflash chip select dfsi 16 out - dataflash serial input (to dataflash) dfso 21 in pd - dataflash serial output (from dataflash). this pin has a built-in pull- down. it may be left open if not used. dfsck 15 out - dataflash data clock p1.15 - p1.11 30, 62, 61, 54, 53 i/o pu - five general-purpose i/o pins. these pins have built-in pull-ups. they may be left open if not used. x1 - x2 45, 44 - - external crystal connection. standard frequencies are 6.9552 mhz, 9.6 mhz, 11.2896 mhz, 12.288 mhz. max frequency is 12.5 mhz. an external clock (max. 1.8v pp ) can be connected to x1 using ac coupling (22 pf). a built-in pll multiplies the clock frequency by 4 for internal use. lft 47 - - pll decoupling rcr filter reset 22 in - master reset schmitt trigger input, active low. reset should be held low during at least 10 ms after power is applied. on the rising edge of reset , the chip enters an initialization routine, which may involve firmware download from an external smartmedia, dataflash or host. stin 23 in pd - serial test input. this is a 57.6 kbaud asynchronous input used for firmware debugging. this pin is tested at power-up. the built-in debugger starts if stin is found high. stin has a built-in pull-down. it should be grounded or left open for normal operation. stout 24 out - serial test output. 57.6 kbaud async output used for firmware debugging. pdwn 20 in - power down input, active low. high level on this pin is typ. vc18. when pdwn is low, the oscillator and pll are stopped, the power switch opens, and the chip enters a deep sleep mode (1 a typ. consumption when power switch is used). to exit from power down, pdwn has to be set high then reset applied. alternate programmable power-downs are available which allow warm restart of the chip. test 33 in pd - test input. should be grounded or left open. table 2. pinout by pin name (continued) pin name pin number type sharing description
10 ATSAM3103 6093a?drmsd?25-oct-04 pinout by pin number table 3. atsam3133 pinout by pin number pin # pin name pin # pin name pin # pin name pin # pin name 1wr smc p0.12 17 pwrout 33 test 49 d0 i/o0 p0.0 wsad0 2rd r|b p0.13 18 pwrin 34 daad0 p0.15 50 d1 i/o1 p0.1 wsad1 3 vc33 19 gnd 35 daad1 51 d2 i/o2 p0.2 wsad2 4gnd 20pdwn 36 gnd 52 d3 i/o3 p0.3 wsad3 5 ckout 21 dfso 37 daad2 53 p1.11 6 clbd 22 reset 38 daad3 54 p1.12 7 wsbd 23 stin 39 dabd0 55 d4 i/o4 p0.4 clad0 8 irq smre fs0 p0.8 24 stout 40 dabd1 56 d5 i/o5 p0.5 clad1 9 midi_in p0.14 sdin 25 gnd 41 dabd2 57 gnd 10 midi_out fs1 p0.9 26 smcle p1.2 42 dabd3 58 d6 i/o6 p0.7 clad2 11 mute p1.6 27 smwe p1.3 43 gnd 59 d7 i/o7 p0.7 clad3 12 vc18 28 smale p1.4 44 x2 60 a0 smpd p0.10 sclk 13 gnd 29 smce p1.5 45 x1 61 p1.13 14 dfcs 30 p1.15 46 vc18 62 p1.14 15 dfsck 31 vc18 47 lft 63 vc18 16 dfsi 32 vc33 48 gnd 64 cs p0.11 sync
11 ATSAM3103 6093a?drmsd?25-oct-04 mechanical dimensions figure 7. thin plastic 64-lead quad flat pack (tqfp64) table 4. package dimensions in mm denomination min nom max a 1.40 1.50 1.60 a1 0.05 0.10 0.15 a2 1.35 1.40 1.45 l 0.45 0.60 0.75 d 12.00 d1 10.00 e 12.00 e1 10.00 p0.50 b 0.17 0.22 0.27
12 ATSAM3103 6093a?drmsd?25-oct-04 electrical characteristics absolute maximum ratings(*) recommended operating conditions note: 1. operation at lower v c33 values down to v c18 is possible, however external timing may be impaired. please contact atmel in case of use of these circuits with v c33 outside the recommended operating range. ambient temperature (power applied)................-40 c to 85 c *notice: stresses beyond those listed under "absolute maximum ratings" may cause permanent dam- age to the device. this is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the recommended operating conditions of this specification is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. storage temperature ........................................-65 c to 150 c voltage on any pin x1, lft ....................................................... -0.3 to v c18 + 0.3v others ......................................................... -0.3 to v c33 + 0.3v supply voltage .......................................................................... v c18 .................................................................... -0.3v to 1.95v v c3 .......................................................................-0.3v to 3.6v maximum iol per i/o pin................................................. 4 ma table 5. recommended operating conditions symbol parameter min typ max unit v c18 supply voltage 1.65 1.8 1.95 v v c33 supply voltage (1) 33.3v c18 + 1.5 3.6 v pwrin supply voltage pwrin pin 1.75 1.9 1.95 v t a operating ambient temperature 0 - 70 c
13 ATSAM3103 6093a?drmsd?25-oct-04 dc characteristics table 6. dc characteristics (t a = 25c, v c18 = 1.8v 10%, v c33 = 3.3v 10%) symbol parameter min typ max unit v il low level input voltage -0.3 - 1.0 v v ih high level input voltage, except x1, pdwn 2.3 - v c33 + 0.3 v v ih high level input voltage x1, pdwn 1.2 - v c18 + 0.3 v v ol low level output voltage i ol = -2 ma - - 0.4 v v oh high level output voltage i oh = 2 ma 2.9 - - v i cc1 v c18 power supply current (crystal freq. = 11.2896 mhz, all three p24s running) -40-ma i cc2 v c18 power supply current (crystal freq. = 11.2896 mhz, all p24s stopped) -22-ma i cc3 v c18 power supply current (crystal freq. = 11.2896 mhz, all p24s stopped, warm start power-down active) -4-ma i cc4 v c18 deep power down supply current (using power switch) -110a pu/pd built-in pull-up/pull-down resistor 10 - 56 k ?
14 ATSAM3103 6093a?drmsd?25-oct-04 peripherals and timings slave 8-bit parallel interface pins used: d7-d0 (i/o), cs (input), a0 (input), wr (input), rd (input), irq (output). this interface is typically used to connect the chip to a host processor. timings figure 8. host interface read cycle figure 9. host interface write cycle table 7. timing parameters symbol parameter min typ max unit t av cs address valid to chip select low 0 - - ns t cslrdl chip select low to rd low 5 - - ns t rdhcsh rd high to cs high 5 - - ns t prd rd pulse width 50 - - ns t rdldv data out valid from rd - - 20 ns t drh data out hold from rd 5 - 10 ns t cslrwrl chip select low to wr low 5 - - ns t wrhcsh wr high to cs high 5 - - ns t pwr wr pulse width 50 - - ns t dws write data setup time 10 - - ns t dwh write data hold time 0 - - ns a0 d0 - d7 t avcs t cslrdl t prd t rdhcsh t rdldv t drh cs rd a0 d0 - d7 t avcs t cslwrl t pwr t wrhcsh t dws t dwh cs wr
15 ATSAM3103 6093a?drmsd?25-oct-04 io status register status register is read when a0 = 1, rd = 0, cs = 0. te: transmit empty if 0, data from ATSAM3103 to host is pending and irq is high. reading the data at a0 = 0 will set te to 1 and clear irq. rf: receiver full if 0, then ATSAM3103 is ready to accept data from host. note: if status bit rf is not checked by host, write cycle time should not be lower than 3 s. smartmedia and other peripheral interfaces this is a master 8-bit parallel interface that provides connection to smartmedia or other peripherals such as lcd screens. pins used: i/o7 - i/o0 (i/o), smpd (input), smce , smale, smcle, smre , smwe (outputs) all these pins are fully under firmware control, therefore timing compatibility is ensured by firmware only. eeprom/dataflash interface this is a master synchronous serial interface, operating in spi mode 0. pins used: dfcs , dfsi, dfsck (outputs), dfso (input) the dfsck frequency is firmware programmable from fck to fck/64, where fck is the crystal frequency. thus a large variety of eeprom/dataflash devices can be accomodated. please refer to atmel dataflash datasheets for accurate spi mode 0 timing. figure 10. typical dataflash interface timing 76543210 terfxxxxxx lsb msb dfsck dfsi dfso
16 ATSAM3103 6093a?drmsd?25-oct-04 serial slave synchronous interface the ATSAM3103 can be controlled by an external host processor through the unidirec- tional serial interface. however, no firmware can be downloaded at power-up through this interface. therefore an external rom/flash/eeprom is r equired. pins used: sclk, sync, sdin (input), int (output) data is shifted msb first. the ic samples an incoming sdin bit on the rising edge of sclk, therefore the host should change sdin on the negative sclk edge. sync allows initial synchronization. the rising edge of sync, which should occur with sclk low, indicates that sdin will hold msb data on the next rising sclk. the data is stored internally in a 256-byte fifo. when the fifo count is below 64, the int output goes low. this allows the host proces- sor to send data in burst mode. the maximum sclk frequency is fck (fck being the crystal frequency). the minimum time between two bytes is 64 fck periods. the contents of the sdin data are defined by the firmware. figure 11. serial slave interface typical timing digital audio pins used: clbd (output), wsbd (output), dabd3 - 0 (outputs), daad3 - 0 (inputs) optionally: clad3 - 0 (inputs), wsad3 - 0 (inputs) the ATSAM3103 allows for 8 digital audio output channels and 8 digital audio input channels. all audio channels are normally synchronized on single clocks clbd, wsbd which are derived from the ic crystal oscillator. however, as a firmware option, the daad3 - 0 inputs can be synchronized with incoming clad3 - 0 and wsad3 - 0 sig- nals. in this case, the incoming sampling frequencies must be lower or equal to the chip sampling frequency. the digital audio timing follows the i2s standard, with up to 24 bits per sample msb sclk sync sdin
17 ATSAM3103 6093a?drmsd?25-oct-04 figure 12. digital audio t c is related to t ck , the crystal period at x1 as follows: the choice of sample frequency is done by the firmware. figure 13. digital audio frame format, 128 x fs and 256 x fs modes t cw wsbd t cw t clbd t sod t sod clbd dabd3 - 0 daad3 - 0 table 8. digital audio timing parameters symbol parameter min typ max unit t cw clbd rising to wsbd change t c - 10 - - ns t sod dabd valid prior/after clbd rising t c - 10 - - ns t clbd clbd cycle time - 2 * t c -ns table 9. sample frequency sample frequency wsbd typical sample frequency t c clbd/wsbd frequency ratio 1/(t ck * 128) 96 khz t ck 64 1/(t ck * 192) 64 khz 2 * t ck 48 1/(t ck * 256) 48 khz 2 * t ck 64 1/(t ck * 384) 32 khz 4 * t ck 48 wsbd dabd3 - 0 daad3 - 0 clbd msb lsb 16 bits lsb 24 bits msb
18 ATSAM3103 6093a?drmsd?25-oct-04 figure 14. digital audio frame format, 192 x fs and 384 x fs modes serial midi_in and midi_out the serial midi in and out signals are asynchronous signals following the midi trans- mission standard: baud rate: 31.25 khz format: start, 8 data bits, 1 stop wsbd dabd3 - 0 daad3 - 0 clbd msb lsb 16 bits lsb 24 bits msb
19 ATSAM3103 6093a?drmsd?25-oct-04 reset and power-down during power-up, the reset input should be held low until the crystal oscillator and pll are stabilized, which takes max. 10 ms. after the low-to-high transition of reset , the following occurs: all p24s enter an idle state. p16 program execution starts in built-in rom. the power-up sequence is as follows: stin is sensed. if high, then the built-in debugger is started. smc is sensed. if low, then the built-in loader waits for smartmedia presence detect (smpd). when detected, the firmware is downloaded from smartmedia reserved sector 1 and started. an attempt is made to read the first two bytes of an external eeprom or dataflash. if ?dr? is read, then the built-in loader loads the firmware from the external eeprom/dataflash and starts it. firmware download from a host processor is assumed. 1. the byte 0ach is written to the host, this raises irq. the host can recognize that the chip is ready to accept program download. higher speed transfer can be reached by po lling the parallel interface status (cs = 0, a0 = 1, rd = 0). 2. the host sends the firmware size (in words) on two bytes (low byte first). 3. the host sends the ATSAM3103 firmware. the firmware should begin with string ?dr?. 4. the byte 0ach is written to the host, this raises irq. the host recognizes that the chip has accepted the firmware. 5. ATSAM3103 starts the firmware. if pdwn is asserted low, then the crystal oscillator and pll are stopped. if the power switch is used, then the chip enters a deep power-down sleep mode, as power is removed from the core. to exit power down, pdwn has to be asserted high, then reset applied. other power reduction features allowing warm restart are controlled by firmware: p24s can be individually stopped. the clock frequency can be internally divided by 256.
20 ATSAM3103 6093a?drmsd?25-oct-04 recommended board layout like all hcmos high integration ics, the following simple rules of board layout are man- datory for reliable operation: gnd, vc33, vc18 distribution and decouplings all gnd, vc33, vc18 pins should be connected. a gnd plane is strongly recom- mended. the board gnd + vc33 distribution should be in grid form. recommended vc18 decoupling is 0.1 f at each corner of the ic with an additional 10 f decoupling close to the crystal. vc33 requires a single 0.1f decoupling. crystal, lft the paths between the crystal, the crystal compensation capacitors, the lft filter r-c- r and the ATSAM3103 should be short and shielded. the ground return from the com- pensation capacitors and lft filter should be the gnd plane from ATSAM3103. buses a ground plane should be implemented below the d0 - d7 bus, which is connected to the host and to the ATSAM3103 gnd. a ground plane should be implemented below the wa0 - wa21/wd0 - wd15 bus, which is connected to the rom/flash grounds and to the ATSAM3103. analog section a specific agnd ground plane should be provided, which is connected to the gnd ground by a single trace. no digital signals should cross the agnd plane. refer to the codec vendor recommended layout for correct implementation of the ana- log section.
21 ATSAM3103 6093a?drmsd?25-oct-04 recommended crystal compensation and lft filter figure 15. recommended crystal compensation and lft filter x1 x2 lft x1 1 nf 10 nf gnd 22 pf 22 pf 560
22 ATSAM3103 6093a?drmsd?25-oct-04 product development and debugging atmel provides an integrated product development and debugging tool samvs. samvs runs under windows ? (98, me, 2000, xp). within the environment, it is possible to: edit assemble debug on real target (in-circuit emulation) program dataflash, eeprom, smartmedia on target. two dedicated ic pins, stin and stout allow running firmware directly into the target using standard pc com port communication at 57.6 kbauds. thus time-to-market is optimized by testing directly on the final prototype. a library of frequently used functions is available, such as: reverb/chorus mp3 decode 31-band equalizer parametric equalizer atmel engineers are available to study customer-specific applications.
23 ATSAM3103 6093a?drmsd?25-oct-04 document details title ATSAM3103 literature number 6093 revision history version a publication date: 25-oct-04
printed on recycled paper. disclaimer: the information in this document is provided in connection with atmel products. no license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of atmel products. except as set forth in atmel?s terms and condi- tions of sale located on atmel?s web site, atmel assumes no liability whatsoever and disclaims any express, implied or statutor y warranty relating to its products including, but not limited to, the implied warranty of merchantability, fitness for a particu lar purpose, or non-infringement. in no event shall atmel be liable for any direct, indirect, consequential, punitive, special or i nciden- tal damages (including, without limitation, damages for loss of profits, business interruption, or loss of information) arising out of the use or inability to use this document, even if atmel has been advised of the possibility of such damages. atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the rig ht to make changes to specifications and product descriptions at any time without notice. atmel does not make any commitment to update the information contained her ein. atmel?s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. atmel corporation atmel operations 2325 orchard parkway san jose, ca 95131, usa tel: 1(408) 441-0311 fax: 1(408) 487-2600 regional headquarters europe atmel sarl route des arsenaux 41 case postale 80 ch-1705 fribourg switzerland tel: (41) 26-426-5555 fax: (41) 26-426-5500 asia room 1219 chinachem golden plaza 77 mody road tsimshatsui east kowloon hong kong tel: (852) 2721-9778 fax: (852) 2722-1369 japan 9f, tonetsu shinkawa bldg. 1-24-8 shinkawa chuo-ku, tokyo 104-0033 japan tel: (81) 3-3523-3551 fax: (81) 3-3523-7581 memory 2325 orchard parkway san jose, ca 95131, usa tel: 1(408) 441-0311 fax: 1(408) 436-4314 microcontrollers 2325 orchard parkway san jose, ca 95131, usa tel: 1(408) 441-0311 fax: 1(408) 436-4314 la chantrerie bp 70602 44306 nantes cedex 3, france tel: (33) 2-40-18-18-18 fax: (33) 2-40-18-19-60 asic/assp/smart cards zone industrielle 13106 rousset cedex, france tel: (33) 4-42-53-60-00 fax: (33) 4-42-53-60-01 1150 east cheyenne mtn. blvd. colorado springs, co 80906, usa tel: 1(719) 576-3300 fax: 1(719) 540-1759 scottish enterprise technology park maxwell building east kilbride g75 0qr, scotland tel: (44) 1355-803-000 fax: (44) 1355-242-743 rf/automotive theresienstrasse 2 postfach 3535 74025 heilbronn, germany tel: (49) 71-31-67-0 fax: (49) 71-31-67-2340 1150 east cheyenne mtn. blvd. colorado springs, co 80906, usa tel: 1(719) 576-3300 fax: 1(719) 540-1759 biometrics/imaging/hi-rel mpu/ high speed converters/rf datacom avenue de rochepleine bp 123 38521 saint-egreve cedex, france tel: (33) 4-76-58-30-00 fax: (33) 4-76-58-34-80 literature requests www.atmel.com/literature 6093a?drmsd?25-oct-04 ? atmel corporation 2004 . all rights reserved. atmel ? , logo and combinations thereof, dream ? and dataflash ? are registered trademarks, and everywhere you are sm is the trademark of of atmel corporation or its subsidiaries. windows ? 98, windows ? 2000, windows ? me and win- dows ? xp are the registered trademarks of microsoft corporation. smartmedia ? is the trademark of sandisk corp. mpeg layer-3 audio decod- ing technology licensed from fraunhofer iis and thomson multimedia. other terms and product names may be the trademarks of othe rs.

▲Up To Search▲

Price & Availability of ATSAM3103

	To Download ATSAM3103 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .