SS-L cs-2461 10/21/04 page 1 of 4 features ? advanced laser light source and patented optical design. ? sleek low-profile housing (1.66"/ 42.164 mm height). sensitivity to 0.03%/foot. rotary decade address switches. set 01 ? 99. dual bi-color (red/green) leds flash green when normal and are steady red in alarm. compatible with the 602, 610, 632, 654 and 658 with smart scan? slc. dual led design provides 360 viewing angle. built-in magnetic test switch, or automatic test commanded from panel. optional relay, isolator, or sounder bases. listings listings and approvals below apply to the SS-L laser smoke detector. in some cases, certain modules may not be listed by certain approval agencies, or listing may be in process. consult factory for latest listing status. ul listed: file s1195. SS-L laser smoke detector description the gamewell smart scan tm SS-L laser detector pro- vides a revolutionary ad- vance in early warning smoke detection technol- ogy. the unique design of this detector, combined with enhanced algorithms in the gamewell ? control panels, allows smoke de- tection sensitivity that is 10 to 50 times higher than present photoelectric tech- nology. because of this high sensitivity, the SS-L can provide very early warning of slow smoldering fires. its performance is comparable to present as- piration technology, at a substantially lower in- stalled cost. the SS-L uses an ex- tremely bright laser diode, combined with special lens and mirror optics (u.s. patent pending) , to achieve a signal-to-noise ratio that is much higher than tradi- tional photoelectric sensors. in addition, the tightly focused light beam, com- bined with algorithms, allow the system to differentiate between dust and smoke particles. because of this differentiation, the SS-L can be set to extremely high sensitivity, yet can reject false signals caused by larger airborne particles such as dust, lint, and small insects (u.s. patents pending) . installation the SS-L plug-in detector uses a separate base to simplify installation, service, and maintenance. a special tool allows maintenance personnel to plug-in and re- move detectors without using a ladder. mount base on a box which is at least 1.5" (38.1 mm) deep. suitable mounting base boxes include: 4" (101.6 mm) square box. 3-1/2" (88.9 mm) or 4" (101.6 mm) octagonal box. single-gang box (except relay or isolator base). SS-L with ss-b6 base (top), b501 base (middle), and rmk400 recessed mounting kit (bottom). 5306p1.jpg 6714recs.jpg 5306p2.jpg
SS-L cs-2461 10/21/04 page 2 of 4 specifications operating voltage range 15 to 28 vdc. maximum standby current 230 a @ 24 vdc (no communication). maximum average standby current 255 a @ 24 vdc (one communica- tion every 5 seconds with led blink en- abled). maximum alarm current 6.5 ma @ 24 vdc (led ?on?). operating humidity range 10% to 93% relative humidity, non- condensing. operating temperature range 0 to 49c (32 to 120f). dimensions height: 1.66 inches (42.16 mm) in- stalled in ss-b6 base. diameter: 6.1 inches (154.94 mm) installed in ss-b6 base; 4.1 inches (104.14 mm) installed in b501 base. weight: 3.6 oz. (102 g). bases available: ss-b6: 6.1 inches (154.94 mm) diam- eter. b501: 4.1 inches (104.14 mm) diam- eter. b501bh: sounder base assembly. in- cludes b501 base. b224rb relay base: screw terminals: up to 14 awg (2.00 mm2). relay type: form-c. rating: 2 a @ 30 vdc resis- tive; 0.3 a @ 110 vdc inductive; 1.0 a @ 30 vdc inductive. dimensions: 6.2 in. (157.48 mm) x 1.2 in. (30.48 mm). b224bi isolator base: dimensions: 6.2 in. (157.48 mm) x 1.2 in. (30.48 mm). maximum: 25 devices between isolator bases. recommended coverage per detector in order to support sophisticated smoke/dust discrimination algorithms (cooperating multi-detector), it is recommended that at least two SS-L detectors be installed in each room or enclosed area. recommended coverage per detector is 400 square feet (37.16 square meters). ordering information SS-L laser detector. intelligent laser sensor with smart scan tm capabilities. mounts to one of the bases listed below. bases: ss-b6 standard u.s. low-profile base. b501bh sounder base, includes b501 base. b224rb intelligent relay base. b224bi intelligent isolator base. isolates slc from loop shorts. accessories: ra400z remote led annunciator. 3 - 32 vdc. fits u.s. single-gang electrical box. mod400r detector sensitivity test tool. use with most analog or digital multimeters. satisfies requirement of nfpa72 for sensitivity testing. m02-04-01 test magnet. m02-09-00 test magnet with telescope stick. wiring diagram (standard base) SS-L design the SS-L incorporates an extremely bright laser diode and integral lens that focuses the light beam to a very small volume near the receiving photo sensor. the light then passes into a light trap and is absorbed. the photo sensor is activated by a scattering of smoke particles in this small-volume light beam. in a typical photoelectric detector, the light beam is very wide and can reflect off the chamber walls into the photo sensor because dust accumulation changes the wall color from flat black to gray. with the SS-L, the concentrated light beam does not touch the walls, therefore it is much less susceptible to dust accumulation. smoke scatters light in all directions and, in a typical photoelectric detector, only a small portion of that scattered light reaches the photo sensor itself. in the SS-L, a special mirror reflects and concentrates most of the scattered light into the photo sensor. see laser detail drawings on following page. compared to smoke, airborne dust particles are very large and very sparse. since a) they are in motion; b) the illuminated volume is very small; and c) the SS-L flashes the laser only every few seconds; then the occasional dust particle cannot remain in the light volume for more than one or two samples. this transient signal from dust is the key to the dust discrimination.
SS-L cs-2461 10/21/04 page 3 of 4 mirror detail laser diode & integral lens assembly smoke direction baffles sensing chamber laser beam light trap photo receiver mirror (see detail at right) protective housing safety interlocks (4) smoke sensing chamber cover/screen smoke sensingchamber base spring contact to bug screen contacts to mounting brack- ets smoke detector base rf shield chamber cover bug screen circuit board photo diode test led 5306d2.wmf 5306mir.wmf 5306d1.wmf
SS-L cs-2461 10/21/04 page 4 of 4 gamewell 12 clintonville road northford, ct 06472-1610 phone: 203-484-7161 fax: 203-484-7118 www.gamewell.com a honeywell company ? 2004 gamewell specifications and wiring information are provided for information only and are believed to be accurate. gamewell assumes no responsibility for their use. data and design are subject to change without notice. installation and wiring instructions shipped with the product shall always be used for actual installation. for more information, contact gamewell.
|
