Part Number Hot Search : 
NP175014 E001159 D1212 CS2012 40D112K G1427 109215 LM3580
Product Description
Full Text Search
 

To Download FTP-632MCL304 Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
  24v drive interface board (parallel) ftp-622dcl001/011/ ftp-622dsl001/011/012 1. centronics (1) connector (cn1) connector part number : fcn-605q030-g/s (fujitsu components) mating connector part number : fcn-607b030-g/d (fujitsu components) or equivalent no. signal i/o contents no. signal i/o contents 1 prstb i data strobe 2 prstb-ret connected to logic gnd 3 prdt0 i data 0 4 prdt0-ret connected to logic gnd 5 prdt1 i data 1 6 prdt1-ret connected to logic gnd 7 prdt2 i data 2 8 prdt2-ret connected to logic gnd 9 prdt3 i data 3 10 prdt3-ret connected to logic gnd 11 prdt4 i data 4 12 prdt4-ret connected to logic gnd 13 prdt5 i data 5 14 prdt5-ret connected to logic gnd 15 prdt6 i data 6 16 prdt6-ret connected to logic gnd 17 prdt7 i data 7 18 prdt7-ret connected to logic gnd 19 acknlg o data input acknowledge 20 acknlg-ret connected to logic gnd 21 busy o busy 22 busy-ret connected to logic gnd 23 rinf2 o printer status 24 inprm-ret connected to logic gnd 25 slctin i printer select 26 inprm i reset 27 rinf1 o printer status 28 rinf3 o printer status 29 atf i paper feed request 30 gnd logic gnd (2) connector pin assignment notes: ? symbol means a negative logic signal. ? Cret signal is a return signal of the twisted pair cable. ? i or o means a signal direction from the interface board side. n interface (3) connector pin number fcn-605q030-g/s (fujitsu components) or equivalent (4) data input signal timing no.1 no. 2 no. 30 prdt0~7 pr s t b b u s y acknlg t1 t 3 t 2 t 4 t 5 : t1 3 0 . 5 m sec : t 2 3 0 . 5 m sec : t 3 3 0 . 5 m sec pr s t b t o b u s y = h acknlg pul se : t 4 0 . 5 m sec : t 5 = 5 . 0 m sec . . d a t a se t t im e pr s t b pul se d a t a h ol d t im e for ftp-622/632/642mcl001/002/301/302/303/304 1
2 ftp-622dcl/dsl n specification item specification data receive speed 19200, 9600, 4800, 1200 bps (set by dip switch) synchronous method asynchronous, full duplex hand shake dtr/dsr signal or xon/xoff input output level rs232c signal level space (logic = 0) +3 v ~ +12 v mark (logic = 0) C3 v ~ C12 v (1) connector (cn2) part number : b6b-xh-a (j.s.t) mating connector part number : xhp-6 (j.s.t) or equivalent no. signal i/o contents no. signal i/o contents 1 fg frame gnd 2 rd i receive data 3 td o transmission data 4 dtr o data terminal ready 5 gnd signal gnd 6 dsr i data set ready (3) pin number b6b-xh-a (j.s.t) (2) pin assignment 2. serial interface (rs232c) notes: i or o means a signal direction from the interface board side. 61 cn2 cn1 t c u d o r pr e b m u n t r a pn o i t c n u f d r a o b e c a f r e t n i l e l l a r a p 1 0 0 l c d 2 2 6 - p t f) r e t t u c t u o h t i w ( d r a d n a t s 1 1 0 l c d 2 2 6 - p t fl o r t n o c r e t t u c h t i w d r a o b e c a f r e t n i l a i r e s 1 0 0 l s d 2 2 6 - p t f) r e t t u c t u o h t i w ( d r a d n a t s 1 1 0 l s d 2 2 6 - p t fr e l l o r t n o c r e t t u c h t i w 2 1 0 l s d 2 2 6 - p t fm o r h s a l f + r e l l o r t n o c r e t t u c h t i w 2 1 1 l s d 2 2 6 - p t fm o r h s a l f + i j n a k + r e t t u c h t i w
3 ftp-622dcl/dsl n connector pin assignment 1. connector for power supply (cn10) part number : b6p-vh (j.s.t) mating connector part number : vhr-6n (j.s.t) or equivalent no. signal i/o contents no. signal i/o contents 1v cc power supply for logic (+5 v) 2 gnd gnd (5 v, 24 v common) 3 gnd gnd (5 v, 24 v common) 4 gnd gnd (5 v, 24 v common) 5v dd power for head/motor (+24 v) 6 v dd power for head/motor (+24 v) 2. connector for thermal head drive (cn8) part number : b16b-ph-k-s (j.s.t) mating connector part number : phr-16 (j.s.t) or equivalent no. signal i/o contents no. signal i/o contents 1 vdh o power for head (+24 v) 2 vdh o power for head (+24 v) 3 gnd (vdh) head gnd 4 gnd (vdh) head gnd 5 stb1 o print enable signal 1 6 stb2 o print enable signal 2 7 stb3 o print enable signal 3 8 tmp i temperature detection signal 9 stb4 o print enable signal 4 10 lat o print data latch signal 11 stb5 o print enable signal 5 12 5 vh o power for logic (+5 v) 13 hclk o data transmission clock 14 hd o print data output signal 15 gnd (vdh) head gnd 16 vdh o power for head (+24 v) notes: ? symbol means a negative logic signal. ? i or o means a signal direction from the interface board side. 3. connector for sensor (cn3) part number : b5b-ph-k-s (j.s.t) no. signal i/o contents no. signal i/o contents 1 +5 v power for logic (+5 v) 2 pes i paper end detect signal 3 gnd (5 v) logic gnd 4 +5 v power for logic (+5 v) 5 hup i head-up detect signal
4 ftp-622dcl/dsl no. signal i/o contents no. signal i/o contents 1 nc no connection 2 nc no connection 3 nc no connection 4 nc no connection 5 nc no connection 6 nc no connection 7 nc no connection 8 nc no connection 9 nc no connection 10 nc no connection 11 nc no connection 12 nc no connection 13 nc no connection 14 nc no connection 15 nc no connection 16 nc no connection 17 nc no connection 18 nc no connection 19 nc no connection 20 nc no connection 21 nc no connection 22 nc no connection 23 nc no connection 24 nc no connection 25 slctin i select signal 26 inprm i reset signal 27 nc no connection 28 nc no connection 29 atf i paper feed request 30 gnd gnd 7. connector for control signal input/ output (cn1) part number : fcn-605q030-g/s (fujitsu components) mating connector : fcn-607b030-g/d (fujitsu components) or equivalent *do not connect outside signal to nc.
5 ftp-622dcl/dsl no. signal i/o contents no. signal i/o contents 1 mt/b o stepping motor coil excitation 2 mt/b o stepping motor coil excitation 3 mt/a o stepping motor coil excitation 4 mt/a o stepping motor coil excitation no. signal i/o contents no. signal i/o contents 1 +5 v power for logic (+5 v) 2 nes i paper near end detect signal 5. connector for stepping motor drive (cn13) part number : b4b-ph-k-s (j.s.t) 4. connector for paper near end detection (cn5) part number : b2b-ph-k-s (j.s.t) mating connector part number : phr-2 (j.s.t) or equivalent 6. connector for cutter drive (cn11) * 1 part number : b4b-eh (j.s.t) no. signal i/o contents no. signal i/o contents 1 sw1 i cutter position detect signal 2 gnd logic ground 3 m+ o motor control signal (+) 4 m- o motor control signal (-) *1: only for ftp-622dcl011/111.
6 ftp-622dcl/dsl n printing commands (centronics interface) (continued) command contents ht moves the print position to the next tab. lf line feed. ff feeds forms (new page). esc rs sets reverse printing. esc us resets reverse printing. esc ! +n sets print mode. esc* +m+n 1 +n 2 +d 1 ~d n sets the bit image mode m for n1, n2 dot numbers. esc 2 sets 1/6 inch line feed length. esc 3 + n sets the line feed length. esc @ printer initialization. esc a+n sets the space between lines. esc c+n sets the page length by character line. esc d+d 1 ~d n +nul sets the tab position. esc j+n feeds paper in forward direction. esc k+n feeds paper in reverse direction. esc c+1+n sets the internal processing. esc r+n selects the international character. esc s+n sets the printing speed. esc d+n printing and n-line feeding. esc e+n reverse line feed in n lines after printing. esc t+n character code table selection. esc {+n sets/resets the upside down printing. ecs em+n automatic paper feed distance setting. esc x+n+m setting turning time of the motor excitation. esc v+n right rotation 90 specification / cancellation. fs e+n correction of impressed energy. fs ! +n sets the kanji print mode* 1 . fs & sets kanji mode* 1 . esc %+n selects the font to download* 3 . esc &+y+c1+c2+x+d1~dn registers the download front* 3 . esc ?+n external character registration deletion* 3 .
7 ftp-622dcl/dsl command contents fs . resets kanji mode* 1 . fs c+n selects kanji code type* 1 . fs 9+n sets the detection functions. fs*+m+n1+n2+d1~dn prints image data on sram* 3 . fs r+n notifies of printing finish* 4 . fs w+n sets/resets 4 times enlarged character. gs a+m+n sets the line feed length after mark detection. gs e+n sets print quality . gs v+n+m executes paper cutting* 2 . gs e+n+m sets the bar width. gs h+n sets the barcode height. gs k+m+n+d 1 ~d n selects the barcode type and prints. gs w+n sets the barcode length. gs &+m+x+y1+y2+[d]k registration of image data* 3 . gs '+m+n prints registered image data * 3 . gs a+n sets and cancels status transmission (valid only for dsl)* 3 . (continued) *1: only for ftp-622dsl112. *2: only for ftp-622dcl011 or ftp-622dsl011/012. *3: only for ftp-622dsl012. *4: only for ftp-622dsl011/012. gs < line feeds to the next mark.
8 ftp-622dcl/dsl n options 1. cable (with ftp-622mcl, ftp-632mcl, ftp-642mcl) 2. paper holder name part number flange ftp-040hf stand ftp-040hs e m a nr e b m u n t r a ph t g n e l e l b a c * ) 8 n c ( e l b a c n o i t c e n n o c d a e h l a m r e h t 1 0 0 y 2 2 6 - p t f) s e h c n i 6 . 0 1 ( m m 0 7 2 e l b a c e c a f r e t n i ) 1 n c ( s c i n o r t n e c1 0 2 y 2 2 6 - p t f) s e h c n i 1 7 . 9 1 ( m m 0 0 5 ) 2 n c ( l a i r e s1 0 3 y 2 2 6 - p t f) s e h c n i 1 7 . 9 1 ( m m 0 0 5 ) 0 1 n c ( c i g o l d n a , r o t o m , d a e h r o f e l b a c r e w o p 1 0 4 y 2 2 6 - p t f) s e h c n i 8 . 1 1 ( m m 0 0 3 n o i t p o e l b a c t r o h s * 1 0 0 y 4 2 6 - p t f) s e h c n i 9 . 5 ( m m 0 5 1 ? 2004 fujitsu components america, inc. all company and product names are trademarks or registered trademarks of their respective owners. rev. 11/15/2004. japan fujitsu component limited gotanda-chuo building 3-5, higashigotanda 2-chome, shinagawa-ku tokyo 141, japan tel: (81-3) 5449-7010 fax: (81-3) 5449-2626 email: promothq@ft.ed.fujitsu.com web: www.fcl.fujitsu.com north and south america fujitsu components america, inc. 250 e. caribbean drive sunnyvale, ca 94089 u.s.a. tel: (1-408) 745-4900 fax: (1-408) 745-4970 email: marcom@fcai.fujitsu.com web: www.fcai.fujitsu.com europe fujitsu components europe b.v. diamantlaan 25 2132 wv hoofddorp netherlands tel: (31-23) 5560910 fax: (31-23) 5560950 email: info@fceu.fujitsu.com web: www.fceu.fujitsu.com asia pacific fujitsu components asia ltd. 102e pasir panjang road #04-01 citilink warehouse complex singapore 118529 tel: (65) 6375-8560 fax: (65) 6273-3021 email: fcal@fcal.fujitsu.com www.fcal.fujitsu.com fujitsu components international headquarter offices


▲Up To Search▲   

 
Price & Availability of FTP-632MCL304

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X