 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| product specification main features ? 8-bit resolution. ? adc gain adjust. ? 2 ghz full power input bandwidth. ? 1 gsps (min) sampling rate. ? sinad = 45 db (7.4 effective bits) sfdr = 58 dbc @ f s = 1 gsps, f in = 20 mhz : ? sinad = 44 db (7.2 effective bits) sfdr = 56 dbc @ f s = 1 gsps, f in = 500 mhz : ? sinad = 42 db (7.0 effective bits) sfdr = 52 dbc @ f s = 1 gsps, f in = 1000 mhz (-3 db fs) ? 2-tone imd : -52dbc (489 mhz, 490 mhz) @ 1gsps. ? dnl = 0.3 lsb inl = 0.7 lsb. ? low bit error rate (10 -13 ) @ 1 gsps ? very low input capacitance : 0.4 pf ? 500 mvpp differential or single-ended analog inputs. ? differential or single-ended 50 ? ecl compatible clock inputs. ? ecl or lvds/hstl output compatibility. ? data ready output with asynchronous reset. ? gray or binary selectable output data ; nrz output mode. ? power consumption : 3.4w @ tj = 90c ? dual power supply : 5 v ? radiation tolerance oriented des ign (150 krad (si) measured). applications ? digital sampling oscilloscopes. ? satellite receiver. ? electronic countermeasures / electronic warfare. ? direct rf down ? conversion. screening ? atmel-grenoble standard die flow. ? temperature range : 0c < ta ; tj < +90c description the jts8388b is a monolithic 8?bit anal og?to?digital converter, designed for digitizing wide bandwidth analog signals at very high sampling rates of up to 1 gsps. the jts8388b is using an innovative ar chitecture, including an on chip sample and hold (s/h), and is fabricated with an advanced high speed bipolar process. the on?chip s/h has a 2 ghz full power input bandwidth, providing excellent dynamic performance in undersampling applications (high if digitizing). adc 8-bit 1 gsps jts8388b 1/ delivered in die form 2/ chip evaluation board : available tsev8388b 3/ cqfp68 packaged device available : refer to ts8388bf datasheet 4/ cbga72 packaged device available: refer to ts8388bg data sheet january 2002
2 jts8388b product specification table of contents 1. simplified block diagram ..................................................................................................... ..................................... 3 2. functional description ....................................................................................................... ....................................... 3 3. specifications ............................................................................................................... ..................................................... 4 3.1. absolute maximum ratings ( see notes below ) .............................................................................................................................. ....4 3.2. recommended conditions of use .............................................................................................. .......................................................4 3.3. electrical operating characteristics....................................................................................... ..................................................5 3.4. t iming d iagrams ............................................................................................................................... ..............................................................9 3.5. explanation of test levels ................................................................................................. .............................................................10 3.6. wafer screening ............................................................................................................ .......................................................................10 3.7. functions description...................................................................................................... ..................................................................11 3.8. digital output coding ...................................................................................................... ...................................................................11 4. package description. ......................................................................................................... ......................................... 13 4.1. jts8388b pin description ................................................................................................... ..................................................................13 4.2. jts8388b chip pad list, coordinates and corresponding functions............................................................ ...................14 4.3. jts8388b chip pads designation vh25b....................................................................................... ....................................................15 4.4. die mechanical informations ................................................................................................ ...........................................................16 5. typical character ization results ............................................................................................. ...................... 17 5.1. static linearity ? fs = 50 msps / fin = 10 mh z ............................................................................................................................... ..17 5.2. effective number of bits versus power supplies variation ................................................................... ..........................18 5.3. typical fft results ........................................................................................................ ......................................................................19 5.4. spurious free dynamic range versus input amplitude ......................................................................... ...............................20 5.5. dynamic performance versus analog input frequency .......................................................................... ...........................21 5.6. effective number of bits (enob) versus sampling frequency .................................................................. ........................22 5.7. sfdr versus sampling frequency ............................................................................................. ....................................................22 5.8. jts8388b adc performances versus junction temperature ...................................................................... ........................23 5.9. typical full power input bandwidth ......................................................................................... ...................................................24 5.10. adc step response......................................................................................................... ..................................................................25 6. definition of terms .......................................................................................................... ............................................ 26 7. applying th e jts8 388b ........................................................................................................ ........................................... 28 7.1. timing informations ........................................................................................................ .....................................................................28 7.2. principle of data ready signal control by drrb input command....................................................................................29 7.3. analog inputs (vin) (vinb) ................................................................................................. ...................................................................29 7.4. clock inputs (clk) (clkb) .................................................................................................. ..................................................................30 7.5. clock signal duty cycle adjust............................................................................................. ........................................................32 7.6. noise immunity informations................................................................................................ ............................................................32 7.7. digital outputs ............................................................................................................ ..........................................................................33 7.8. out of range bit ........................................................................................................... .........................................................................36 7.9. gray or binary output data format select................................................................................... ...........................................36 7.10. ts8388 b thermal requirements............................................................................................. .....................................................36 7.11. diode pad 32 .............................................................................................................. ...........................................................................37 7.12. adc gain control pad 38 ................................................................................................... .............................................................37 8. equivalent input / output schematics ......................................................................................... ................... 38 8.1. equivalent analog input circuit and esd protections ........................................................................ ................................38 8.2. equivalent analog clock input circuit and esd protections.................................................................. .........................38 8.3. equivalent data output buffer circuit and esd protections .................................................................. ........................39 8.4. adc gain adjust equivalent input circuits and esd protections .............................................................. ......................39 8.5. gorb equivalent input schematic and esd protections........................................................................ ..............................40 8.6. drrb equivalent input schematic and esd protections ........................................................................ ..............................40 9. tsev8388b : device evaluation board.......................................................................................... ....................... 42 10. ordering information ........................................................................................................ ................................... 43 jts8388b 3 product specification 1. simplified block diagram g=2 t/h g=1 t/h g=1 clock buffer resisto r chain analog encoding block interpolation stages regeneration latches error correction & decode logic output latches & buffers 4 45 45 8 8 vin,vinb clk, clkb gain drrb dr,drb gorb data,datab or,orb master/slave track & hold amplifier 2. functional description the jts8388b is an 8 bit 1gsps adc based on an advanced high speed bipolar technolog y featuring a cutoff frequency of 25 ghz. the jts8388b includes a front-end master/sla ve track and hold stage (s/h), followed by an analog encoding stage and interpolati on circuitry. successive banks of latches are regenerating the analog residues into logical data before entering an error correction circuit ry and a resynchronization stage followed by 75 ? differential output buffers. the jts8388b works in fully differential mode from analog inputs up to digital outputs. the jts8388b features a full power input bandwidth of 2 ghz. control pin gorb is provided to select either gray or binary data output format. gain control pin is provided in order to adjust the adc gain. the jts8388b uses only vertical isolated npn transistors together with oxide isol ated polysilicon resistors, providing enhanced radiation tolerance (no performance drift measured at 150krad total dose). 4 jts8388b product specification 3. specifications 3.1. absolute maximum ratings (see notes below) parameter symbol comments value unit positive supply voltage v cc gnd to 6 v digital negative supply voltage dv ee gnd to -5.7 v digital positive supply voltage v plusd gnd-0.3 to 2.8 v negative supply voltage v ee gnd to -6 v maximum difference between negative supply voltages dv ee to v ee 0.3 v analog input voltages v in or v inb -1 to +1 v maximum difference between v in and v inb v in - v inb -2 to +2 v digital input voltage v d gorb -0.3 to v cc +0.3 v digital input voltage v d drrb v ee -0.3 to +0.9 v digital output voltage vo v plusd -3 to v plusd -0.5 v clock input voltage v clk or v clkb -3 to +1.5 v maximum difference between v clk and v clkb v clk - v clkb -2 to +2 v maximum junction temperature t j +135 o c storage temperature t stg -65 to +150 o c lead temperature (soldering 10s) t leads +300 o c notes : absolute maximum ratings are limiting values (referenced to g nd=0v), to be applied individually, while other parameters are wit hin specified operating conditions. long exposure to maximum rating may affect device reliability. the use of a thermal heat sink is mand atory (see thermal characteristics page 19). 3.2. recommended conditions of use parameter symbol comments min. typ. max. unit positive supply voltage v cc 4.75 +5 5.25 v positive digital supply voltage v plusd ecl output compatibility gnd v v plusd lvds output compatibility +1.4 +2.4 +2.6 v negative supply voltages v ee, dvee -5.25 -5.0 -4.75 v differential analog input voltage (full scale) v in, v inb v in -v inb 50 ? differential or single-ended 113 450 125 500 137 550 mv mvpp clock input power level p clk p clkb 50 ? single?ended clock input 3 4 10 dbm operating temperature range t j commercial grade: ?c? industrial grade: ?v? military grade: ?m? 0 < tj < 90 -40 < tj < 110 -55 < tj < +125 o c jts8388b 5 product specification 3.3. electrical operating characteristics vee = dvee = -5 v ; v cc = +5 v ; v in -v inb = 500 mvpp full scale differential input ; digital outputs 75 or 50 ? differentially terminated ; tj (typical) = 70 c. full temperature range : up to -55 c < tj < +125 c parameter symb temp test level min typ max unit power requirements positive supply voltage analog digital (ecl) digital (lvds) vcc v plusd v plusd ii,iv 4.75 1.4 5 0 2.4 5.25 2.6 v v v positive supply current analog digital icc i plusd ii, iv 385 115 445 145 ma ma negative supply voltage vee full iv -5.25 -5 -4.75 v negative supply current analog digital aiee diee ii,iv 165 135 200 180 ma ma nominal power dissipation pd full ii iv 3.4 4.1 4.1 4.3 w w power supply rejection ratio (note 2) psrr iv +/- 0.5 mv/v resolution 8 bits analog inputs full scale input voltage range (differential mode) ( 0 volt common mode voltage ) v in v inb full iv -125 -125 125 125 mv mv full scale input voltage range (single?ended input option ) (see application notes) v in v inb full iv -250 0 250 mv mv analog input capacitance c in full iv 0.4 pf input bias current i in full iv 10 a input resistance r in full iv 1 m ? full power input bandwidth fpbw full iv 1.8 ghz small signal input bandwidth (10 % full scale) ssbw full iv 1.9 ghz clock inputs logic compatibility for clock inputs (note 10 ) (see application notes) ecl or specified clock input power level in dbm ecl clock inputs voltages (v clk or v clkb ) : full iv ? logic ?0? voltage v il -1.5 v ? logic ?1? voltage v ih -1.1 v ? logic ?0? current i il 5 a ? logic ?1? current i ih 5 a clock input power level into 50 ? termination dbm into 50 ? clock input power level full iv -2 4 10 dbm clock input capacitance c clk full iv 0.4 3.5 pf 6 jts8388b product specification parameter symb temp test level min typ max unit digital outputs ( notes 1,6 ) single ended or differential input mode, 50 % clock duty cycle (clk,clkb), binary output data format, tj (typical) = 70 c. full temperature range : up to -55 c < tj ; tj < +125 c. logic compatibility for digital outputs ( depending on the value of v plusd ) (see application notes) ecl or lvds differential output voltage swings ( assuming v plusd = 0v) : 75 ? open transmission lines ( ecl levels ) 75 ? differentially terminated 50 ? differentially terminated full iv 1.50 0.70 0.54 1.620 0.825 0.660 v v v output levels ( assuming v plusd = 0v) 75 ? open transmission lines (note 6) 25 c iv ? logic ?0? voltage v ol -1.62 -1.54 v ? logic ?1? voltage v oh -0.88 -0.8 v output levels ( assuming v plusd = 0v) 75 ? differentially terminated (note 6) 25 c iv ? logic ?0? voltage v ol -1.41 -1.34 v ? logic ?1? voltage v oh -1.07 -1 v output levels ( assuming v plusd = 0v) 50 ? differentially terminated (note 6) 25 c ii ? logic ?0? voltage v ol -1.45 -1.32 v ? logic ?1? voltage v oh -1.20 -1.15 v differential output swing dos full vi 250 290 mv output level drift with temperature full iv 1.6 mv/ c dc accuracy single ended or differential input mode, 50 % clock duty cycle (clk,clkb), binary output data format, tj (typical) = 70 c. full temperature range :-55 c < tc ; tj < +125 c. differential non linearity (notes 2,3) dnl full i vi 0.35 0.45 0.6 0.7 lsb lsb integral non linearity (notes 2,3) inl full i vi 0.7 0.9 1 1.2 lsb lsb no missing codes (note 3) full guaranteed over specified temperature range gain error full i vi -10 -11 -2 -2 10 11 % fs % fs input offset voltage full i vi -26 -30 -5 -5 26 30 mv mv gain error drift offset error drift full full iv iv 100 40 125 50 150 60 ppm/ c ppm/ c jts8388b 7 product specification parameter symb temp test level min typ max unit transient performance bit error rate (notes 2, 4) fs = 1 gsps fin = 62.5 mhz ber full iv 1e-12 error/ sample adc settling time (note 2) v in -v inb = 400 mvpp ts iv 0.5 ns overvoltage recovery time (note 2) ort iv 0.5 ns ac performance single ended or differential input and clock mode, 50 % clo ck duty cycle (clk,clkb), binary output data format, tj. = 70 c, unless otherwise specified. signal to noise and distortion ratio (note 2) sinad full iv fs = 1 gsps fin = 20 mhz 43 45 db fs = 1 gsps fin = 500 mhz 42 44 db fs = 1 gsps fin = 1000 mhz (-1db fs) 40 42 db fs = 50 msps fin = 25 mhz 40 44 db effective number of bits enob full iv fs = 1 gsps fin = 20 mhz 7.0 7.2 bits fs = 1 gsps fin = 500 mhz 6.6 6.8 bits fs = 1 gsps fin = 1000 mhz (-1dbfs) 6.2 6.4 bits fs = 50 msps fin = 25 mhz 7 7.2 bits signal to noise ratio (note 2) snr full iv fs = 1 gsps fin = 20 mhz 42 45 db fs = 1 gsps fin = 500 mhz 41 44 db fs = 1 gsps fin = 1000 mhz (-1dbfs) 41 44 db fs = 50 msps fin = 25 mhz 44 45 db total harmonic distortion (note 2) thd full iv fs = 1 gsps fin = 20 mhz 50 54 db fs = 1 gsps fin = 500 mhz 46 50 db fs = 1 gsps fin = 1000 mhz (-1dbfs) 42 46 db fs = 50 msps fin = 25 mhz 46 51 db spurious free dynamic range (note 2) sfdr full iv fs = 1 gsps fin = 20 mhz - 52 - 57 dbc fs = 1 gsps fin = 500 mhz - 47 - 52 dbc fs = 1 gsps fin = 1000 mhz (-1dbfs) - 42 - 47 dbc fs = 1 gsps fin = 1000 mhz (-3dbfs) - 45 - 50 dbc fs = 50 msps fin = 25 mhz -40 -54 dbc two-tone inter-modulation distortion (note 2) imd full iv f in1 = 489 mhz @ f s = 1 gsps - 47 - 52 dbc f in2 = 490 mhz @ f s = 1 gsps 8 jts8388b product specification parameter symb temp test level min typ max unit switching performance and characteristics ? see timing diagrams figure 1, figure 2 maximum clock frequency f s full 1 1.4 gsps minimum clock frequency f s full iv 10 msps minimum clock pulse width (high) tc1 full iv 0.280 0.500 50 ns minimum clock pulse width (low) tc2 full iv 0.350 0.500 50 ns aperture delay (note 2) ta full iv 100 +250 400 ps aperture uncertainty (notes 2, 5) jitter 25 o c iv 0.4 0.6 ps (rms) data output delay (notes 2, 10, 11, 12) tod full iv 1150 1360 1660 ps output rise/fall time for data (20 % ? 80 %) (note 11 ) tr/tf full iv 250 350 550 ps output rise/fall time for data ready (20 % ? 80 % ) (note 11 ) tr/tf full iv 250 350 550 ps data ready output delay (notes 2,10, 11, 12) tdr full iv 1110 1320 1620 ps data ready reset delay trdr full iv 720 1000 ps tod-todr (notes 9, 13) tod- tdr full iv 40 40 40 ps tc1+tdr-tod see timing diagram (note 2) @ 1gsps td1 full iv 460 460 460 ps data pipeline delay tpd full iv 4 clock cycles note 1 : differential output buffers are internally loaded by 75 ? resistors. buffer bias current = 11 ma. note 2 : see definition of terms note 3 : histogram testing based on sa mpling of a 10 mhz sinewave at 50 msps. note 4 : output error amplitude < 4 lsb around worst code. note 5 : maximum jitter value obtained for single?ended clo ck input on the jts8388b die (chip on board) : 200 fs. (500 fs expected on jts8388b) note 6 : digital output back termination options depicted in application notes figures 3,4,5 . note 7 : with a typical value of td = 465 ps, at 1 gsps, the timi ng safety margin for the data storing using the eclinps 10e452 output registers from motorola is of 315 ps, equally shared before and after the risi ng edge of the data ready signals (dr, drb). note 8 : the clock inputs may be indifferently entered in different ial or single?ended, using ecl levels or 4 dbm typical power level into the 50 ? termination resistor of the inphase clock input. (4 dbm into 50 ? clock input correspond to 10 dbm power level for the clock generator.) note 9 : at 1gsps, 50/50 clock duty cycle, tc2 = 500 ps (tc1). tdr - tod = -100 ps (typ) does not depend on the sampling rate. note 10 : specified loading c onditions for digital outputs : - 50 ? or 75 ? controlled impedance traces properly 50 / 75 ? terminated, or unterminated 75 ? controlled impedance traces. - controlled impedance traces far end loaded by 1 standard eclinps register from motorola.( e.g. : 10e452 ) ( typical input par asitic capacitance of 1.5 pf includi ng package and esd protections. ) note 11 : termination load parasi tic capacitance derating values : - 50 ? or 75 ? controlled impedance traces properly 50 / 75 ? terminated : 60 ps / pf or 75 ps per additionnal eclinps load. - unterminated ( source terminated ) 75 ? controlled impedance lines : 100 ps / pf or 1 50 ps per additionnal ec linps termination load. note 12 : apply proper 50 / 75 impedance traces propagation time derat ing values : 6 ps / mm (155 ps/inch) for tsev8388b evaluat ion board. note 13 : values for tod and tdr track each other over temperature, ( 1 % variation for tod - tdr per 100 o c. temperature variation ). therefore tod - tdr variation over temperature is negligible. moreover, the internal ( onchip ) and pack age skews between each data tods and tdr effect can be considered as negligib le.consequently, minimum values for tod and t dr are never more than 100 ps apart. the s ame is true for the tod and tdr maximum values (see advanced application notes about tod - t dr variation over temperature in sectio n 7). jts8388b 9 product specification 3.4. timing diagrams tc1 tc2 ta= 250 ps x x n+1 x n+2 x n+3 n figure 1 jts8388b timing diagram ( 1 gsps clock ) data read y reset , clock held at low digital outputs (v in, v inb ) data ready (dr, drb) (clk, clkb) x n+5 td1=tc1+tdr-tod = tc1-40 ps = ps data n-4 data n-3 data n data n-1 data n-2 tc=1000 ps x x n+4 tod = 1360 ps 1360 p s drr 1ns (min) tdr = 1320 ps tpd: 4.0 clock 1000 trdr = 920 n-1 td2 = tc2+tod- = tc2+40ps = 540 tdr = 1320 ps data n-5 data n+1 tc1 tc2 ta= 250ps x x n+1 x n+2 x n+3 n figure 2 jts8388b timing diagram ( 1 gsps clock ) data ready reset , clock held at high digital outputs (v in, v inb ) data ready (dr, drb) (clk, clkb) x n+5 td1=tc1+tdr-tod = tc1-40 ps = 460 data n-4 data n-3 data n data n-1 data n-2 tc = 1000 ps x x n+4 tod = 1360 1360 drrb 1ns tdr = 1320 tpd: 4.0 clock 1000 trdr = 920ps n-1 td2 = tc2+tod-tdr = tc2+40ps = 540 ps tdr = 1120 data n-5 data n+1 10 jts8388b product specification 3.5. explanation of test levels d 100 % wafer tested at +25 c (1) i 100% production tested at +25 c (1) (for packaged device). ii 100 % production tested at +25 c (1) , and sample tested at specified temperatures iii sample tested only at specified temperatures iv parameter is guaranteed by design and characteriza tion testing (thermal steady-state conditions at specified temperature). v parameter is a typical value only vi 100 % production tested over specified temperature range. only min and max values are guaranteed (typical val ues are issuing from characterization results). (1) unless otherwise specified, all tests are pulsed tests : therefore tj = tc = ta, 3.6. wafer screening parameter temperature jts8388b chip unit min max dc accuracy @ 50 msps / 10 mhz dnl lsb inl 25 c (2) lsb no missing codes guaranteed ac performance tbd snr 45 db enob 25 c (2) 7.1 bit (2) unless otherwise specified, all tests are pulsed tests : therefore tj = tc = ta, jts8388b 11 product specification 3.7. functions description name function vcc positive power supply vee analog negative power supply vplusd digital positive power supply gnd ground vin, vinb differential analog inputs clk, clkb differential clock inputs 12 jts8388b product specification +126 mv +124 mv positive 1/2 scale + 1/2 lsb positive1/2 scale ? 1/2 lsb 11000000 10111111 10100000 11100000 0 0 +1 mv -1 mv bipolar zero + 1/2 lsb bipolar zero - 1/2 lsb 10000000 01111111 11000000 01000000 0 0 -124 mv -126 mv negative 1/2 scale + 1/2 lsb negative 1/2 scale - 1/2 lsb 01000000 00111111 01100000 00100000 0 0 -249 mv -251 mv negative full scale + 1/2 lsb negative full scale - 1/2 lsb 00000001 00000000 00000001 00000000 0 0 < -251 mv < negative full scale - 1/2 lsb 00000000 00000000 1 jts8388b 13 product specification 4. package description. 4.1. jts8388b pin description symbol pin number function gnd 20, 24, 26, 28, 33, 35, 37 analog ground. pads n20, 24,26,28,37 are double. pads n26,33,35 are single. 14 bonding wires are available for analog ground access. v plusd 1, 11 digital positive supply. (0v for ecl compatibility, +2.4v for lvds compatibility). 2 double pads (note 3) v cc 19, 21, 23, 30, 39, 40 +5 v positive supply. v ee 22, 29, 31 -5 v analog supply. dv ee 6 -5 v digital supply. v in 34 in phase (+) analog input signal of the sample and hold differential preamplifier. v inb 36 inverted phase (-) of analog input signal. clk 25 in phase (+) ecl clock input. clkb 27 inverted phase (-) of ecl clock input. d0, d1, d2, d3, d4, d5, d6, d7 16, 14, 12, 9, 4, 2, 45, 43 in phase (+) digital outputs. d0 is the lsb. d7 is the msb. d0b, d1b, d2b, d3b, d4b, d5b, d6b, d7b 17, 15, 13, 10, 5, 3, 46, 44 inverted phase (-) digital outputs. b0b is the inverted lsb. d7b is the inverted msb. or 41 in phase (+) out of range output. out of range goes high on the leading edge of code 0 and code 256. orb 42 inverted phase (+) of out of range bit (or). dr 7 in phase (+) output of data ready signal. drb 8 inverted phase (-) output of data ready signal. gorb 18 gray or binary select output format control pad. ? binary output format if gorb is floating or v cc . ? gray output format if gorb is connected at ground (0 v). gain 38 adc gain adjust pin. diod/drrb 32 diod : die junction temperature measurement pad. can be left floating or grounded if not used. drrb : asynchronous data ready reset function 14 jts8388b product specification 4.2. jts8388b chip pad list, coordi nates and corresponding functions pad number posx posy chip pad function 1 880 1365 v plusd positive digital supply (double pad) (note 3) 2 670 1365 d5 in phase (+) digital output, bit 5 (d7 is the msb ; bit 7, d0 is the lsb ; bit 0) 3 510 1365 d5b inverted phase (-)digital output, bit 5 4 350 1365 d4 in phase (+) digital output, bit 4 5 190 1365 d4b inverted phase (-) digital output, bit 4 6 -20 1365 dv ee -5v digital supply (double pad) 7 -230 1365 dr in phase (+) data ready 8 -390 1365 drb inverted phase (-) data ready 9 -550 1365 d3 in phase (+) digital output, bit 3 10 -710 1365 d3b inverted phase (-) digital output, bit 3 11 -920 1365 v plusd positive digital supply (double pad) (note 3) 12 -1085 1115 d2 in phase (+) digital output, bit 2 13 -1085 955 d2b inverted phase (-) digital output, bit 2 14 -1085 795 d1 in phase (+) digital output, bit 1 15 -1085 635 d1b inverted phase (-) digital output, bit 1 16 -1085 475 d0 in phase (+) digital output, bi t 0, least significant bit 17 -1085 315 d0b inverted phase (-) digital output, bit 0, least significant bit 18 -1085 155 gorb gray or binary data output format select. (note 2) 19 -1085 -55 v cc +5v supply (double pad) 20 -1085 -325 gnd analog ground (double pad) 21 -1085 -595 v cc +5v supply (double pad) 22 -1085 -865 v ee -5v analog supply (double pad) 23 -1085 -1135 v cc +5v supply (double pad) 24 -905 -1365 gnd analog ground (double pad) 25 -655 -1365 clk in phase (+) clock input (double pad) 26 -455 -1365 gnd analog ground 27 -255 -1365 clkb inverted phase (-) clock input (double pad) 28 -5 -1365 gnd analog ground (double pad) 29 245 -1365 v ee -5v analog supply (double pad) 30 495 -1365 v cc +5v supply (double pad) 31 745 -1365 v ee -5v analog supply (double pad) 32 945 -1365 diod/drrb diode input for tj monitoring / input for asynchronous data ready reset 33 1085 -1195 gnd analog ground 34 1085 -995 v in in phase (+) analog input (double pad) 35 1085 -795 gnd analog ground 36 1085 -595 v in b inverted phase (-) analog input (double pad) 37 1085 -345 gnd analog ground (double pad) 38 1085 -145 gain adc gain adjust input 39 1085 55 v cc +5v supply (double pad) 40 1085 265 v cc +5v supply 41 1085 425 or in phase (+) out of range digital output 42 1085 585 orb inverted phase (-) out of range digital output 43 1085 745 d7 in phase (+) digital output, bi t 7, most significant bit 44 1085 905 d7b inverted phase (-) digital output bit 7 45 1085 1065 d6 in phase (+) digital output, bit 6 46 1085 1225 d6b inverted phase (-) digital output, bit 6 note 1 : coordinates are relative to pad centers. the co ordinates origin (0,0) is at the center of the die. all dimensions are given in microns. the pad 1 is the one pointed at by the arrow (see layout). distance between pad (glass window) and inner edge of seal-ring : 40m. die size (inner edge of seal-ring : (-1175, -1175, 1455). die size (including scribe line) : (-1230, -1510) (1230, 1510) (2.46 x 3.02 mm2). actual die size (after separation) : (-1220, -1500) (1220, 1500) (2.44 mm x 3.00 mm). note 2 : gorb tied to vcc or floating : binary output data format. gorb tied to gnd : gray output data format note3 : the common mode level of the output buffers is 1.2v below the positive digital supply. for ecl compatibility the positive digital supply must be set at 0v (ground). for lvds compatibility (output common mode at +1.2v) the positive digital supply must be set at 2.4v. if the subsequent lvds circuitry c an withstand a lower level for input common mode, it is recommended to lower the positive dig ital supply level in the name proportion in order to spare power dissipation. jts8388b 15 product specification 4.3. jts8388b chip pads designation vh25b die size : 2.44 x 3.00 mm (after separation) die area : 7.32 mm2 vplusd vplusd dvee or orb d7 d7b d6 d6b vcc vcc vcc vcc gnd gnd vee vee d5b d5 d4 d4b drb dr d3 d3b d2 d2b d1 d1b d0 d0b g orb vcc gnd clk clkb gnd vee gnd vcc gnd gnd vinb vin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 gain diod/drrb 16 jts8388b product specification 4.4. die mechanical informations mask reference..........................................................vh25b die size between scribe line axis......................2.46 mm x 3.02 mm after separation ...................................2.44 mm x 3.00 mm prad size (single pad) .........................................100 m x 100 m (double pad)........................................200 m x 100 m die thickness .............................................................300 m 20 m back side metallization..............................................none metallization number of layers.................................3 material ...............................................ti/tin al-si-cu tin (on top) diffusion barrier...................................ti/tin thickness............................................metal 1 : 600 nm : metal 2 & metal 3 : 800 nm pad metallization (1) (2) ................................................ti/tin al-si-cu tin (metal 2) ti/tin al-si-cu tin (metal 3) passivation ............................................................oxide/nitride (sio 2 /sin 2 ) : 300nm / 550 nm back side potential ....................................................-5v die transistor count ...................................................4450 die attach ..................................................................epoxy ag fill ed high conductivity glue bond wire ..................................................................al or au 30 m diameter qualification package ................................................cqfp68 (with re striction on electrical performance) note 1 : the top tin layer is etched in one step together with the passivation layer. note 2 : the pad is a sandwich of metal 2 and metal 3 over field oxyde. jts8388b 17 product specification 5. typical characterization results 5.1. static linearity ? fs = 50 msps / fin = 10 mhz 5.1.1. i ntegral n on l inearity lsb inl = +/- 0.7 lsb code signal frequency = 10mhz clock frequency = 50msps positive peak : 0.78 lsb negative peak : -0.73 lsb 5.1.2. d ifferential n on l inearity lsb dnl = +/- 0.4 lsb code signal frequency = 10mhz clock frequency = 50msps positive peak : 0.3 lsb negative peak : -0.39 lsb 18 jts8388b product specification 5.2. effective number of bits versus power supplies variation 0 1 2 3 4 5 6 7 8 -7 -6,5 -6 -5,5 -5 -4,5 -4 effective number of bits = f ( veea ) ; fs = 500 m sps ; fin = 100 mhz veea ( v ) enob (bits) 0 1 2 3 4 5 6 7 8 3 3,5 4 4,5 5 5,5 6 6,5 7 effective number of bits = f ( vcc ) ; fs = 500 m sps ; fin = 100 mhz vcc ( v ) enob (bits) jts8388b 19 product specification 5.3. typical fft results 5.3.1. f s = 1 g sps , f in =20 mh z 5.3.2. f s = 1 g sps , f in = 495 mh z 5.3.3. f s = 1 g sps , f in = 995 mh z ( -3 d b f ull s cale input ) single ended or differential fs =1 gsps fin = 20 mhz eff. bits =7.2 sinad = 45 db snr = 45 db thd = -54 dbc sfdr = -57 dbc h3 h2 clock duty cycle = 50 % binary output coding h11 h12 single ended or differential fs =1 gsps fin=495mhz eff. bits =6.8 sinad = 44 db snr = 44 db thd = -50 dbc sfdr= -52 dbc clock duty cycle = 50 % h3 h11 h14 h12 binary output coding h2 single ended or differential fs =1 gsps fin=995 mhz eff. bits =6.4 sinad =42 db snr = 44 db thd = -46 dbc sfdr= -50 dbc clock duty cycle = 50 % h2 h3 binary output coding h10 20 jts8388b product specification 5.4. spurious free dynamic range versus input amplitude 5.4.1. sampling frequency f s =1 g sps ; i nput frequency f in =995 mh z ; g ray or b inary output coding fs = 1 gsps fin = 995 mhz full scale enob = 6.4 sinad = 42 db snr = 44 db thd = 46 dbc sfdr = -47 dbc full scale magnitude (code) sfdr = -47 dbc h2 h3 -3db full scale fs = 1 gsps fin = 995 mhz (-3 db full scale) enob = 6.6 sinad = 43 db snr = 44 db sfdr = -50 dbc magnitude (code) thd = -48 dbc sfdr = -50 dbc h2 h3 jts8388b 21 product specification 5.5. dynamic performance versus analog input frequency fs=1 gsps, fin = 0 up to 1600 mhz, full scale input (fs), fs -3 db clock duty cycle 50 / 50, binary/gray output coding, fully differential or single-ended analog and clock inputs 3 4 5 6 7 8 0 200 400 600 800 1000 1200 1400 1600 1800 input frequency (mhz) enob (db) -3 db fs fs - 10 db fs 30 32 34 36 38 40 42 44 46 48 50 0 200 400 600 800 1000 1200 1400 1600 1800 input frequency (mhz) snr (db) fs -3 db fs -10 db fs -60 -55 -50 -45 -40 -35 -30 -25 -20 0 200 400 600 800 1000 1200 1400 1600 1800 2000 input frequency (mhz) sfdr (dbc) -3 db fs fs -10 db fs 22 jts8388b product specification 5.6. effective number of bits (enob) versus sampling frequency analog input frequency : fin = 495 mhz and nyquist conditions ( fin = fs / 2 ) clock duty cycle 50 / 50 , binary output coding 2 3 4 5 6 7 8 0 200 400 600 800 1000 1200 1400 1600 sampling frequency (msps) enob (db) fin= fs/2 fin=500 mhz 5.7. sfdr versus sampling frequency analog input frequency : fin = 495 mhz and nyquist conditions ( fin = fs / 2 ) clock duty cycle 50 / 50 , binary output coding -60 -55 -50 -45 -40 -35 -30 -25 -20 0 200 400 600 800 1000 1200 1400 1600 sampling frequency (msps) sfdr (dbc) fin= fs/2 fin=500 mhz jts8388b 23 product specification 5.8. jts8388b adc performances versus junction temperature 3 4 5 6 7 8 -40 -20 0 20 40 60 80 100 120 140 160 effective number of bits versus junction temperature fs = 1 gsps ; fin = 500 mhz ; duty cycle = 50% temperature ( o c) enob (bits) 42 43 44 45 46 -40 -20 0 20 40 60 80 100 120 140 signal to noise ratio versus junction temperature fs = 1 gsps ; fin = 507 mhz ; differential clock, single-ended analog input (vin=-1dbfs) temperature ( o c) snr (db) 43 45 47 49 51 53 -60 -40 -20 0 20 40 60 80 100 120 140 total harmonic distorsion versus junction temperature fs = 1 gsps ; fin = 507 mhz ; differential clock, single-ended analog input (vin=-1dbfs) temperature ( o c) thd (db) 24 jts8388b product specification 0 1 2 3 4 5 -40 -20 0 20 40 60 80 100 120 140 160 power consumption versus junction temperature fs = 1 gsps ; fin = 500 mhz ; duty cycle = 50% temperature ( o c) power consumption (w) 5.9. typical full power input bandwidth 2 ghz at -3 db (-2dbm full power input) -6 -5 -4 -3 -2 -1 0 400 600 800 1000 1200 1400 1600 1800 2000 2200 frequency (mhz) magnitude (db) jts8388b 25 product specification 5.10. adc step response test pulse input characteristics : 20% to 80% input full scale and rise time ~ 200ps. 5.10.1. t est pulse digitized with 20 gh z dso 50 mv/div 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 0 time (ns) vpp ~ 260 mv tr ~ 240 ps 50 mv/div 500 ps/div 5.10.2. s ame test pulse digitized with jts8388b adc 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 0 200 150 100 50 0 adc code time (ns) tr ~ 280 ps 50 codes/div (vpp ~260 mv) 500 ps/div adc calculated rise time : between 150 and 200 p s. n.b. : ripples are due to the test setup (they are present on both measurements) 26 jts8388b product specification 6. definition of terms (ber) bit error rate probability to exceed a specified error threshold fo r a sample. an error code is a code that differs by more than +/- 4 lsb from the correct code. (bw) full power input bandwidth analog input frequency at which the fundamental component in the digitally reconstructed output has fallen by 3 db with respect to its low fr equency value (determined by fft analysis) for input at full scale. (sinad) signal to noise and distortion ratio ratio expressed in db of the rms signal amp litude, set to 1db below full scale, to the rms sum of all other spectral component s, including the harmonics except dc. (snr) signal to noise ratio ratio expressed in db of the rms signal amp litude, set to 1db below full scale, to the rms sum of all other spectral component s excluding the five first harmonics. (thd) total harmonic distortion ratio expressed in dbc of the rms sum of the first five harmonic components, to the rms value of the measured fundamental spectral component. (sfdr) spurious free dynamic range ratio expressed in db of the rms signal amplit ude, set at 1db below full scale, to the rms value of the next highest spectral component (peak spurious spectral component). sfdr is the key parameter for selecting a converter to be used in a frequency domain application ( radar systems, digital receiver, network analyzer ....). it may be reported in dbc (i.e., degrades as signal levels is lowered), or in dbfs (i.e . always related back to converter full scale). (enob) effective number of bits where a is the actual input amplitude and v is the full scale range of the adc under test (dnl) differential non linearity the differential non linearity for an output code i is the difference between the measured step size of code i and the ideal lsb step size. dnl (i ) is expressed in lsbs. dnl is the maximum value of all dnl (i). dnl error specification of less than 1 lsb guarantees that there are no missing output codes and that the transfer function is monotonic. (inl) integral non linearity the integral non linearity for an output code i is the difference between the measured input voltage at which the transition occurs and the ideal value of this transition. inl (i) is expressed in lsbs, and is the maximum value of all | inl (i) | . (dg) differential gain the peak gain variation (in percent ) at five different dc levels for an ac signal of 20% full scale peak to peak amplitude. f in = 5 mhz. (tbc) (dp) differential phase peak phase variation (in degrees) at five different dc levels for an ac signal of 20% full scale peak to peak amplitude. f in = 5 mhz. (tbc) (ta) aperture delay delay between the rising edge of the differential clock inputs (clk,clkb) (zero crossing point), and the time at which (v in, v inb ) is sampled. (jitter) aperture uncertainty sample to sample variation in aperture delay. the voltage error due to jitter depends on the slew rate of the signal at the sampling point. (ts) settling time time delay to achieve 0.2 % accuracy at the converter output when a 80% full scale step function is applied to the differential analog input. (ort) overvoltage recovery time time to recover 0.2 % accuracy at the output, after a 150 % full scale step applied on the input is reduced to midscale. (tod) digital data output delay delay from the falling edge of the differential cl ock inputs (clk,clkb) (zero crossing point) to the next point of change in the differential output data (zero crossing) with specified load. (td1) time delay from data to data ready time delay from data transition to data ready. (td2) time delay from data ready to data general expression is td1 = tc1 + tdr - tod with tc = tc1 + tc2 = 1 encoding clock period. (tc) encoding clock period tc1 = minimum clock pulse width (high) tc = tc1 + tc2 tc2 = minimum clock pulse width (low) (tpd) pipeline delay number of clock cycles between the sampling edge of an input data and the associated output data being made available, (not taking in account the tod). for the jts8388b the tpd is 4 clock periods. sinad - 1.76 + 20 log (a/v/2) enob = ??????????????? 6.02 jts8388b 27 product specification (trdr) data ready reset delay delay between the falling edge of the data ready output asynchronous reset signal (ddrb) and the reset to digital zero transition of the data ready output signal (dr). (tr) rise time time delay for the output data signals to rize from 20% to 80% of delta between low level and high level. (tf) fall time time delay for the output data signals to fall from 80% to 20% of delta between low level and high level. (psrr) power supply rejection ratio ratio of input offset variation to a change in power supply voltage. (nrz) non return to zero when the input signal is larger than the upper bound of the adc input range, the output code is identical to the maximum code and the out of range bit is set to logic one. when the input signal is smaller than the lower bound of the adc i nput range, the output code is identical to the minimum code, and the out of range bit is set to logic one. (it is assumed that the input signal amplitude remains within the absolute maximum ratings). (imd) intermodulation distortion the two tones intermodulation distortion ( imd ) reje ction is the ratio of either input tone to the worst third order intermodulation products. the input tones levels are at - 7db full scale. (npr) noise power ratio the npr is measured to characterize the a dc performance in response to broad bandwidth signals. when using a notch-filtered broadband white-noise generator as the input to the adc under test, the noise power ratio is defined as the ratio of the average out-of-notch to the average in-notch power spectral density magnit udes for the fft spectrum of the adc output sample test. 28 jts8388b product specification 7. applying the jts8388b 7.1. timing informations 7.1.1. t iming value for jts8388b timing values are given at chip inputs/outputs, taking into a ccount pad and esd protections capac itance, 2 mm (30 um diameter) bonding wire per pad, and specified termination loads. propagation delays in 50/75 ohms impedance traces are not taken into account for tod and tdr. apply proper derating values corre sponding to termination topology. the min/max timing values are valid over the fu ll temperature range in the following conditions : note 1 : specified termination load (differential output datas and data ready) : 50 ohms resistor in parallel with 1 standard ecli nps register from motorola, (e.g : 10e452) (typical eclinps inputs shows a ty pical input capacitance of 1.5 pf (including package and esd protections) if addressing an output dmux, take care if some digital output s do not have the same termination load and apply corresponding d erating value given below. note 2 : output termination load derating values for tod and tdr : ~ 60 ps/pf or 75 ps per additional eclinps load. note 3 :propagation time delay derating values have also to be applied for tod and tdr : ~ 6 ps/mm (155 ps/inch) for tsev8388b evaluation board. apply proper time delay derating value if a different dielectric layer is used. 7.1.2. p ropagation time considerations tod and tdr timing values are given from pin to pin and do not include the additional propagation times between device pins and input/output termination loads. for the tsev838 8b evaluation board, the propagation time delay is 6ps/mm (155ps/inch) corresponding to 3.4 ( @10ghz) dielectric constant of t he ro4003 used for the board. if a different dielectric layer is used (for instanc e teflon), please use appropri ate propagation time values. td does not depend on propagation times because it is a differential data. (td is the time difference between data read y output delay and digital data output delay) td is also the most straightforward data to measure, again because it is differential : td can be measured directly onto terminat ion loads, with matched oscilloscopes probes. 7.1.3. tod - tdr variation over temperature values for tod and tdr track each other over temperature (1 perc ent variation for tod - tdr per 100 degrees celsius temperature variation). therefore tod - tdr variation over temperature is negligible. moreover, the internal (onchip) and package skews between each da ta tods and tdr effect can be considered as negligible. consequently, minimum values for tod and tdr are never more than 100 ps apart. the same is true for the tod and tdr maximum val ues. in other terms : if tod is at 950 ps, tdr will not be at 1420 ps ( maximum time delay for tdr ). if tod is at 1460 ps, tdr will not be at 910 ps ( minimum time delay for tdr ) however, external tod - tdr values may be dictat ed by total digital datas skews between every tods (each digital data) and tdr : mcm board , bonding wires and output lines lengths diffe rences, and output termi nation impedance mismatches. the external (on board) skew effect has not been taken into account for the specification of the minimum and maximum values for tod-tdr. 7.1.4. principle of operation the analog input is sampled on the rising edge of external clock input (clk,clkb) afte r ta (aperture delay) of typically 250ps . the digitized data is available after 4 clock periods latency (pipeline delay (tpd)), on clock rising edge, after 1160 ps typic al propagation delay tod. the data ready differential output signal frequency (dr,drb) is half the external clock frequency, that is it switches at the s ame rate as the digital outputs. the data ready output signal (dr,drb) switches on external clock falling edge after a propagation delay tdr of typically 1120 p s. a master asynchronous reset input command drrb ( ecl compatible single-ended input) is availabl e for initializing the different ial data ready output signal ( dr,drb ) .this feature is mandatory in certain app lications using interleaved adcs or using a single adc with d emultiplexed outputs. actually, without data ready signal initialization, it is im possible to store the output digital datas in a defined order. jts8388b 29 product specification 7.2. principle of data ready signal control by drrb input command 7.2.1. data ready output signal reset the data ready signal is reset on falling edge of drrb input comm and, on ecl logical low level (-1.8v). drrb may also be tied t o vee = - 5v for data ready output signal master reset. so long drrb remains at logical low level, (or tied to vee = - 5v), the data ready outp ut remains at logical zero and is independant of the external free running encoding clock. the data ready output signal (dr,drb) is reset to logical zero after trdr= 720 ps typical. trdr is measured between the -1.3v point of the falling edge of drrb input command and the zero crossing point of the different ial data ready output signal (dr,drb). the data ready reset command may be a pulse of 1 ns minimum time width. 7.2.2. data ready output signal restart the data ready output signal restarts on drrb co mmand rising edge, ecl logical high levels (-0.8v). drrb may also be grounded, or is allowed to float, for normal free running data ready output signal. the data ready signal restart sequence depends on the logical level of the external encoding clock, at drrb rising edge instant : 1) the drrb rising edge occurs when external encoding clock input (clk,clkb) is low : the data ready output first rising edge occurs after half a cl ock period on the clock falling edge, after a delay time tdr = 13 20 ps already defined hereabove. 2) the drrb rising edge occurs when external enc oding clock input (clk,clkb) is high : the data ready output first rising edge occurs after one cl ock period on the clock falling edge, and a delay tdr = 1320ps. consequently, as the analog input is sampl ed on clock rising edge, the first digitiz ed data corresponding to the first acquisit ion ( n ) after data ready signal restart ( rising edge ) is always strobed by the third rising edge of the data ready signal. the time delay (td1) is specified between the last point of a change in the differential output data (zero crossing point) to t he rising or falling edge of the differential data ready signal (dr,drb) (zero crossing point). note 1 : for normal initialization of data ready output signal, t he external encoding clock signal frequency and level must be contro lled. it is reminded that the minimum encoding clock sampling rate for the adc is 10 msps and consequently the clock cannot be stoppe d. note 2 : one single pin is used for both drrb input command and die junction temperature monitoring. pin denomination will be drrb/diod.( on fo rmer version denomination was diod. ) temperature monitoring and data ready cont rol by drrb is not possible simultaneously. 7.3. analog inputs (vin) (vinb) the analog input full scale range is 0.5 volts peak to peak (v pp), or -2 dbm into the 50 ohms termination resistor. in differential mode input configuration, that means 0.25 volt on each input, or +/- 125 mv around zero volt. the input common mode is ground. the typical input capacitance is 0.4 pf in die form (j ts8388b), not taking into account the bond wires capacitance. the input capacitance is mainly due to t he pad capacitance, as the esd protections are not connected (but present) on the input s. differential inputs voltage span -125 125 [mv] -250 mv 250 mv vin 500mv full scale analog input t vinb ( vin,vinb ) = +/- 250 mv = 500 mv diff 0 volt differential versus single ended analog input operation the jts8388b can operate at full speed in eit her differential or single ended configuration. this is explained by the fact the adc us es a high input impedance differential pream plifier stage, (preceeding the sample and h old stage), which has been designed in order to be entered either in differential mode or single?ended mode. 30 jts8388b product specification this is true so long as the out of phase analog input pin vinb is 50 ohms terminated very closely to one of the neighboring shi eld ground pins (33? 35? 37) which constitute the local ground refe rence for the inphase an alog input pin (vin). thus the differential analog input preamplifier will fully reje ct the local ground noise ( and any capacitively and inductively coupled noise) as common mode effects. in typical single?ended configuration, enter on the (vin) input pin, with the inverted phase input pin (vinb) grounded through the 50 ohms termination resistor. in single?ended input configuration, the in- phase input amplitude is 0.5 volt peak to peak,centered on 0v. (or -2 dbm into 50 o hms.) the inverted phase input is at ground potential through the 50 ohms termination resistor. however, dynamic performances can be somewhat improved by entering either analog or clock inputs in differential mode. typical single ended analog input configuration vin or vinb vin or vinb double pad 34, 36 50 ? (external) 50 ? reverse termination 1m ? 3 pf -250 250 [mv] 500 mv 500 mv full scale analog input t vinb vin vinb = 0v v in = +/- 250 mv ? 500 mv diff 7.4. clock inputs (clk) (clkb) the jts8388b can be clocked at full speed wi thout noticeable performance degradation in either differential or single ended con figuration. this is explained by the fact the adc us es a differential preamplifier stage for the clock buffer, which has been designed in o rder to be entered either in differential or single?ended mode. 7.4.1. single ended clock input (g round c ommon m ode ) although the clock inputs were intended to be driven differentially with nominal -0.8v / -1.8v ecl levels, the jts8388b clock b uffer can manage a single?ended sinewave clock signal centered around 0 volt. this is the most convenient cl ock input configuration as it does not require the use of a power splitter. no performance degradation ( e.g. : due to timing jitter) is obs erved in this particular singl e?ended configuration up to 1.2gs ps nyquist conditions ( fin = 600 mhz ). this is true so long as the inverted phase clock input pin is 50 ohms terminated very closely to one of the neighbouring shield ground pin, which constitutes the local ground refer ence for the inphase clock input. thus the jts8388b differential clock input buffer will fully re ject the local ground noise ( and any capacitively and inductive ly coupled noise) as common mode effects. moreover, a very low phase noise sinewave generat or must be used for enhanced jitter performance. the typical inphase clock input amplitude is 1 volt peak to peak, centered on 0 volt (ground) common mode. this corresponds to a typical clock input power leve l of 4 dbm into the 50 ohms termination resistor. do not exceed 10 dbm to avoid saturation of the preamplifier input transistors. the inverted phase clock input is grounded th rough the 50 ohms termination resistor. jts8388b 31 product specification single ended clock input (ground common mode) vclk common mode = 0 volt vclkb=0 volt 4 dbm typical clock input power level (into 50 ohms termination resistor) [v] t vclk vclkb = ( 0 v ) -0.5v +0.5v clk or clkb 50 ? (external) 50 ? reverse termination 1m ? 0.4 pf clk or clkb double pad (25, 27) note 1 : do not exceed 10 dbm into the 50 ohms termination resistor for single clock input power level. 7.4.2. differential ecl clock input the clock inputs can be driven differentially with nominal -0.8v / -1.8v ecl levels. in this mode, a low phase noise sinewave generator can be used to drive the clock inputs, followed by a power splitter (hybrid junction) in order to obtain 180 degrees out of phase sinewave si gnals. biasing tees can be us ed for offseting the common mode voltage to ecl levels. note : as the biasing tees propagation times are not matching, a tunable delay line is required in order to ensure the signals to be 180 degrees out of phase especially at fast clock rates in the gsps range. differential clock inputs (ecl levels) -0.8v [mv] t -1.8v vclkb vclk common mode = -1.3 v clk or clkb 50 ? reverse termination 1m ? 0.4 pf -2v 50 ? (external) clk or clkb double pad (25, 27) 7.4.3. single ended ecl clock input in single?ended configuration enter on clk ( resp. clkb ) pin , with the inverted phase clock input pin clkb (respectively clk) connected to -1.3v through the 50 ohms termination resistor. the inphase input amplitude is 1 volt peak to peak, centered on -1.3 volt common mode. single ended clock input (ecl): vclk common mode = -1.3 volt. vclkb = -1.3 volt -0.8v [v] t -1.8v vclk vclkb = -1.3 v 32 jts8388b product specification 7.5. clock signal duty cycle adjust at fast sampling rates, ( 1 gsps and above), the device performanc e ( especially the snr ) may be improved by tuning the clock duty cycle (clk,clkb). in single ended configuration, when using a sinewave clock generator, the clock signal duty cycle can be easily adjusted by sim ply offseting the inphase clock signal using a biasi ng tee, (as the out of phase clock input is at ground level ). single ended clock input (inphase clock input common mode shifted) vclk common mode = -180mv vclkb = 0 volt [v] t vclk - 180 mv vclkb = ( 0 v ) -0.5v 40 % 60 % +0.5v note 1 : do not exceed 10 dbm into the 50 ohms termination resistor for single clock input power level. note 2 : for an input clk signal of 4 dbm into 50 ohms, the ty pical offset value to achieve a 40 / 60 clock duty cycle is -180 mv on clk. 7.6. noise immunity informations circuit noise immunity perfor mance begins at design level. efforts have been made on the design in order to make the device as insensitive as possible to chip environment perturbations resulting from the circuit itself or induced by external circuitry. (cascode stages isolation, internal damping resistors, clamps, inter nal (onchip) decoupling capacitors.) furthermore, the fully differential operation from analog input up to the digital outputs provi des enhanced noise immunity by c ommon mode noise rejection. common mode noise voltage induced on the differential analog and cl ock inputs will be canceled out by these balanced differenti al amplifiers. moreover, proper active signals shielding has been provided on the chip to reduce the amount of coupled noise on the active inp uts : the analog inputs and clock inputs of the ts8388b device have been surrounded by ground pins, which must be directly connected to the external ground plane. jts8388b 33 product specification 7.7. digital outputs the jts8388b differential output buffers are internally 75 ohms loaded. the 75 ohms resistors are connected to the digital grou nd pins through a - 0.8v level shift diode (see figures 3,4,5 on next page). the jts8388b output buffers are designed for driving 75 ohms (default) or 50 ohms pro perly terminated impedance lines or coaxia l cables. an 11 ma bias current flowing alternately into one of the 75 ohms resistors when switching ensures a 0.825 v voltage drop acros s the resistor (unterminated outputs). the vplusd positive supply voltage allows the adjustment of the output common mode level from -1.2v (vplusd=0v for ecl output c ompatibility) to +1.2v (vplusd=2.4v for lvds output compatibility). therefore, the single ended output voltages vary approximately between -0.8v and -1.625v, ( outputs unterminated ), around -1.2v common mode voltage. three possible line driving and back-terminati on scenarios are proposed (assuming vplusd=0v) : 1 ) 75 ohms impedance transmission lines, 75 ohms differentially terminated (fig. 3) : each output voltage varies between -1v and -1.42v (respectively +1.4v and +1v), leading to +/- 0.41v =0.825 v in differential, around -1.21 v (respectively +1.21v) common mode fo r vplusd=0v (respectively 2.4v). 2 ) 50 ohms impedance transmission lines, 50 ohms differentially termination (fig. 4) : each output voltage varies between -1.02v and -1.35v (respective ly +1.38v and +1.05v), leading to +/- 0.33v=660 mv in different ial, around -1.18v (respectively +1.21v) common mode fo r vplusd=0v (respectively 2.4v). 3 ) 75 ohms impedance open transmission lines (fig. 5) : each output voltage varies between -1.6 v and -0.8 v (respectively +0.8v and +1.6v), which are true ecl levels, leading to +/- 0.8v=1.6v in differential, around -1.2v (respectively +1.2v) common mode for vplusd=0v (respectively 2.4v). therefore, it is possible to drive directly high input impedanc e storing registers, without terminating the 75 ohms transmissio n lines. in time domain, that means that the incident wave will reflec t at the 75 ohms transmission line output and travel back to the g enerator ( i.e. the 75 ohms data output buffer ). as the buffer output impedance is 75 ohms, no back reflection will occur. note : this is no longer true if a 50 ohms transmission line is us ed, as the latter is not matching the buffer 75 ohms output imped ance. each differential output termination length must be kept identical . it is recommended to decouple the midpoint of the differential termi nation with a 10 nf capacitor to avoid common mode perturba tion in case of slight mismatch in the differential output line lengths. too large mismatches ( keep < a few mm ) in the differential li ne lengths will lead to switching currents flowing into the deco upling capacitor leading to switching ground noise. the differential output voltage levels ( 75 or 50 ohms terminati on ) are not ecl standard voltage levels, however it is possib le to drive standard logic ecl circuitry like the eclin ps logic line from motorola. at sampling rates exceeding 1gsps, it may be difficult to tri gger the hp16500 or any other acquisition system with digital outp uts. it becomes necessary to regenerate digital data and data ready by m eans of external amplifiers, in order to be able to test the jts8388b at its optimum performance conditions. 34 jts8388b product specification 7.7.1. differential output loading configurations ( levels for ecl compatibility ) - + 11 ma dvee vplusd = 0v 75 ? 75 ? 75 ? 75 ? impedance 10 nf 75 ? 75 ? out -1v / -1.41v outb -1.41v / -1v differential output : 0.41v = 0.825v common mode level : -1.2v (-1.2v below vplusd level) figure 3 : differential output : 75 ? terminated -0.8v - + 11 ma dvee vplusd = 0v 75 ? 75 ? 50 ? 50 ? impedance 10 nf 50 ? 50 ? out -1.02v / -1.35v outb -1.35v / -1.02v differential output : 0.33v = 0.660v common mode level : -1.2v (-1.2v below vplusd level) figure 4 : differential output : 50 ? terminated -0.8v -+ 11 ma dvee vplusd = 0v 75 ? 75 ? 75 ? 75 ? impedance out -0.8v / -1.6v outb -1.6v / -0.8v differential output : 0.8v = 1.6v common mode level : -1.2v (-1.2v below vplusd level) figure 5 : differential output : open loaded -0.8v jts8388b 35 product specification 7.7.2. differential output loading configurations ( levels for lvds compatibility ) - + 11 ma dvee vplusd = 2.4v 75 ? 75 ? 75 ? 75 ? impedance 10 nf 75 ? 75 ? out 1.4v / 0.99v outb 0.99v / 1.4v differential output : 0.41v = 0.825v common mode level : -1.2v (-1.2v below vplusd level) figure 6 : differential output : 75 ? terminated 1.6v - + 11 ma dvee vplusd = 2.4v 75 ? 75 ? 50 ? 50 ? impedance 10 nf 50 ? 50 ? out 1.38v / 1.05v outb 1.05v / 1.38v differential output : 0.33v = 0.660v common mode level : -1.2v (-1.2v below vplusd level) figure 7 : differential output : 50 ? terminated 1.6v -+ 11 ma dvee vplusd = 2.4v 75 ? 75 ? 75 ? 75 ? impedance out 1.6v / 0.8v outb 0.8v / 1.6v differential output : 0.8v = 1.6v common mode level : -1.2v (-1.2v below vplusd level) figure 8 : differential output : open loaded 1.6v 36 jts8388b product specification 7.8. out of range bit an out of range (or,orb) bit is provided t hat goes to logical high state when the i nput exceeds the positive full scale or fall s below the negative full scale. when the analog input exceeds the positive full scale, the digital output datas remain at high logical state, with (or,orb) at logical one. when the analog input falls below the negative full scale, the digita l outputs remain at logical low state, with (or,orb) at lo gical one again. 7.9. gray or binary output data format select the jts8388b internal regeneration latches i ndecision (for inputs very clos e to latches threshold) may produce errors in the lo gic encoding circuitry and leading to large amplitude output errors. this is due to the fact that the latches are regenerating the in ternal analog residues into logica l states with a finite voltag e gain value (av) within a given positive amount of time ? (t) : av= exp( ? (t)/ ) , with the positive feedback regeneration time constant. the jts8388b has been designed for reducing the probability of occurence of such errors to approximately 10 -13 (targetted for the jts8388b at 1gsps). a standard technique for reducing the amplitude of such errors down to +/-1 lsb consists to output the digital datas in gray co de format. though the jts8388b has been designed for featuring a bit error rate of 10 -13 with a binary output format, it is possible for the user to select between the binary or gray output data format, in order to reduce the amplitude of such errors when occuring, by storing gray o utput codes. digital datas format selection : binary output format if gorb is floating or vcc. gray output format if gorb is connected to ground (0v). 7.10. ts8388 b thermal requirements the jts8388b is currently mounted on its dedicated chip evaluati on board (ceb), with fulfills the device thermal requirements i n still air at room temperature. for operation in the military temperature r ange, forced convection is required to main tain the device junc tion temperature belo w the specified maximum value. the jts8388b power dissipation is 3.6 watt at 70c junction temperature, and 3.8 watt at 125c junction temperature. the die di mensions are 2.44 mm x 3 mm = 7.32 mm2. the maximum junction temperature is 145c. to manage correctly the power dissipation of the jts8388b device, the following thermal fixture profile is used, taking into ac count the die dimensions and power dissipation : 7.5 c/w typical value for die attach ag fill ed epoxy glue, but depending on gllue film thickness. 0.5 c/w copper block. 1 c/w isolation foil. 6.5 c/w heatsink (still air). the heatsink used is the 3334b pin fin heatsink from thermalloy, (also used cooling the 604 power pc p). its dimensions are 50 .70 mm x 50.39 mm = (1.996 inch x 1.984 inch x 0.650 inch). the measured die junction to ambient therma l resistance (rthja) for the chip evaluati on board is approximately 15.5 c/w in stil l air. at room temperature (25c), this yields to a device junction temperature of approxim ately 80c, in thermal steady state conditi ons. jts8388b 37 product specification 7.11. diode pad 32 the diode pad 32 is provided for di e junction temperature monitoring. the operating die junction temperature mu st be kept below145c, therefore an adequate cooling system has to be set up. the diode mounted transistor measured vbe value versus junction temper ature is given below. 600 640 680 720 760 800 840 880 920 960 1000 -55 -35 -15 5 25 45 65 85 105 125 junction temperature (deg.c) vbe (mv) 7.12. adc gain control pad 38 the adc gain is adjustable by the m eans of the pad 38 (input impedance is 1m ? in parallel with 2pf) the gain adjust transfer f unction is given below : 0,80 0,85 0,90 0,95 1,00 1,05 1,10 1,15 1,20 -500 -400 -300 -200 -100 0 100 200 300 400 500 vgain (command voltage) (mv) adc gain 38 jts8388b product specification 8. equivalent input / output schematics 8.1. equivalent analog input circuit and esd protections gnd=0v vcc=+5v vclamp= +2.4v +1.65v -1.55v vee vee vcc gnd vin vinb vee=-5v pad capacitance 340ff pad capacitance 340ff -0.8v -5.8v 5.8v 0.8v 200 ? 200 ? 50 ? 50 ? note : the esd protections are present but not connected for vin and vinb e21v e21v -0.8v -5.8v 8.2. equivalent analog clock inpu t circuit and esd protections vcc=+5v +0.8v gnd=0v vee vee=-5v clk vcc vee clkb pad capacitance 340ff pad capacitance 340ff -5.8v -5.8v -5.8v -5.8v -5.8v -5.8v 5.8v 5.8v 0.8v 0.8v 150 ? 150 ? a380 a note : the esd protections are present but not connected for clk and clkb jts8388b 39 product specification 8.3. equivalent data output buffer circuit and esd protections vplusd=0v to 2.4v dvee=-5v vee=-5v vee=-5v vee vee out outb -5.8v -5.8v 5.8v 5.8v 0.8v 0.8v 0.8v 0.8v i=11ma 75 ? 75 ? -3.7v pad capacitance 180 ff pad capacitance 180 ff note : the esd protection equivalent capacitance is 150 ff. 8.4. adc gain adjust equivalent input circuits and esd protections vee vee vee=-5v vcc=+5v +1.6v pad capacitance 180 ff -0.8 v -5.8 v -0.8 v -5.8 v 0.8v 0.8v 5.8v 0.8v 0.8v 5.8v 1 k ? 1 k ? 2 pf 2 pf gnd gnd vee vee vcc pad capacitance 180 ff 500 a 500 a ga gab np1032c2 np1032c2 note : the esd protection equivalent capacitance is 150 ff. 40 jts8388b product specification 8.5. gorb equivalent input schematic and esd protections gorb: gray or binary select input; floating or tied to vcc -> binary vcc=+5v vee=-5v gnd=0v -0.8v -0.8v -5.8v 5.8v 5.8v 5.8v 5 k ? 1 k ? 1 k ? 1 k ? 250 a 250 a pad capacitance 180ff gorb vee note : the esd protection equivalent capacitance is 150 ff. jts8388b 41 product specification 8.6. drrb equivalent input schematic and esd protections vee=-5v vee vcc=+5v gnd=0v -1.3v -2.6v 10 k ? ? drrb 5.8 v pad capacitance 180 ff actual protection range: 6.6v above vee, in fact stress above gnd are clipped by the cb diode used for tj monitoring 0.8 v np1032c2 note : the esd protection equivalent capacitance is 150 ff. 42 jts8388b product specification 9. tsev8388b : device evaluation board for complete specification, see separate tsev8388b document. general description the tsev8388b evaluation board (ceb) is a prototype board which has been designed in or der to facilitate the evaluation and the characterization of the jts8388b device up to its 2 ghz full power bandwidth at up to 1 gsps in the military temperature range. the high speed of the jts8388b requires careful attention to circuit design and layout to achieve optimal performance. this four metal layer board with internal ground plane has t he adequate functions in order to allow a quick and simple evaluati on of the jts8388b adc performances over the temperature range. the tsev8388b evaluation board is very straightforward as it only implements the jts8388b adc, sma connectors for input / outp ut accesses and a 2.54 mm pitch connector compatible with hp16500c high frequency probes. the board also implements a de?embedding fixture in order to fa cilitate the evaluation of the high frequency insertion loss of the input microstrip lines, and a die junction tem perature measurement setting. the board is constituted by a sandwich of two dielectric layers, featuring low insertion loss and enhanced thermal characterist ics for operation in the high frequency domain and extended temperature range. the board dimensions are 130 mm x 130 mm. the board set comes fully assembled and tested, with the jts8388b die installed. jts8388b 43 product specification 10. ordering information die form j ts ( x ) 8388b - 1 v b die prefix manufacturer prefix (1) prototype version device or family revision of the mask set b : for vh25b screening levels (2) v : visual inspection back side metallization 1 : naked silicon (1) atmel-grenoble (2) for availability of the different versions, contact your atmel- grenoble sales office 1 prob test confi g uration 1 : ambiant temperature 2 : t a m b + hi g h te m p evaluation board evaluation board prefix device or family tsev 8388b 44 jts8388b product specification appendix validity objective specification this datasheet cont ains target and goal specification for discussion with customer and application validation. before design phase. target specification this datasheet contains target and goal specification for product development. valid during the design phase. preliminary specification alpha-site this datasheet contains prelimi nary data. additional data may be published later ; could include simulation results. valid before the characterization phase. preliminary specification beta-site this datasheet contains also charac terization results. valid before the industrialization phase. product specification this datasheet contains final product specifiact ion. valid for production purpose. application information where application information is given, it is adv isory and does not form part of the specification. datasheet status limiting values limiting values given are in accordance with the absolute maximum rating system (iec 134). stress above one or more of the limiting values may cause permanent damage to the device. these are stress ratings only and operation of the device at these or at any other conditions above those given in the characteristics sections of the specification is not implied. exposur e to limiting values for extended periods may affect device reliability. life support applications these products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. atmel customers using or selling these products for use in such applications do so their own risk and agree to fully indemnify atmel for any damages from improper use or sale. jts8388b 45 product specification atmel headquarters corporate headquarters 2325 orchard parkway san jose, ca 95131 tel (408) 441-0311 fax (408) 487-2600 europe atmel sarl route des arsenaux 41 casa postale 80 ch-1705 fribourg switzerland tel (41) 26-426-5555 fax (41) 26-426-5500 asia atmel asia, ltd. room 1219 chinachem golden plaza 77 mody road tsimhatsui east kowloon hong kong tel (852) 2721-9778 fax (852) 2722-1369 japan atmel japan k.k. 9f, tonetsu shinkawa bldg. 1-24-8 shinkawa chuo-ku, tokyo 104-0033 japan tel (81) 3-3523-3551 fax (81) 3-3523-7581 atmel operations atmel colorado springs 1150 e. cheyenne mtn. blvd. colorado springs, co 80906 tel (719) 576-3300 fax (719) 540-1759 atmel rousset zone industrielle 13106 rousset cedex france tel (33) 4-4253-6000 fax (33) 4-4253-6001 atmel smart card ics scottish enterprise technology park east kilbride, scotland g75 0qr tel (44) 1355-357-000 fax (44) 1355-242-743 atmel grenoble avenue de rochepleine bp 123 38521 saint-egreve cedex france tel (33) 4-7658-3000 fax (33) 4-7658-3480 fax-on-demand north america: 1-(800) 292-8635 international: 1-(408) 441-0732 e-mail literature@atmel.com web site http://www.atmel.com bbs 1-(408) 436-4309 ? atmel corporation 2002. atmel corporation makes no warranty for the use of its products , other than those expressly contained in the company?s standard warranty which is detailed in atmel?s terms and conditions located on the company? s web site. the company assumes no responsibility for any error s which may appear in this document, reserves the right to change devices or specifications deta iled herein at any time without notice, and does not make any commitment to update the information contai ned herein. no licenses to patents or other intellectual property of atmel are grant ed by the company in connection with the sale of atmel products, ex pressly or by implication. atmel?s produc ts are not authorized for use as critica l components in life support devices or systems. marks bearing ? and/or ? are registered trademarks and trademarks of atmel corporation. terms and product names in this document may be trademarks of others. this product is manufactured a nd commercialized by atmel grenoble. for further information, please contact : atmel grenoble ? route departementale 128 ? bp 46 ? 91901 orsay cedex ? france phone +33 (0) 1 69 33 03 24 ? fax +33 (0) 1 69 33 03 21 email monique.lafrique@gfo.atmel.com ? web site http://www.atmel-grenoble.com for further technical information, please contact the technical support : email hotline-bdc@gfo.atmel.com |
Price & Availability of JTSX8388B-1V1B
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |