original creation date: 11/24/98 last update date: 03/09/99 last major revision date: 2/16/99 mnclc400a-x rev 2a0 microcircuit data sheet fast settling, wideband low-gain monolithic op amp general description the clc400 is a high-speed, fast-settling operational amplifier designed for low-gain applications. constructed using a unique, proprietary design and an advanced complementary bipolar process, the clc400 offers performance far beyond that normally offered by ordinary monolithic operational amplifiers. in addition, unlike many other high-speed operational amplifiers the clc400 offers both high performance and stability without the need for compensation circuitry - even at a gain of +1. the fast 12ns settling to 0.05% and its ability to drive capacitive loads makes the clc400 an ideal flash a/d driver. the wide bandwidth of 200 mhz and the very linear phase ensure unsurpassed signal fidelity. systems employing digital to analog converters also benefit from the use of the clc400 - especially if linearity and drive levels are important to system performance. the clc400 provides a simple, high-performance solution for video distribution and line driving applications. the 50ma output current and guaranteed specifications for 100 ohm loads provide ample drive capability and assured performance. ns part numbers clc400ae-qml* clc400aj-mls CLC400AJ-QML** industry part number clc400a prime die ub1363b controlling document 5962-8997001pa**, 2a* processing mil-std-883, method 5004 quality conformance inspection mil-std-883, method 5005 subgrp description temp ( c) o 1 static tests at +25 2 static tests at +125 3 static tests at -55 4 dynamic tests at +25 5 dynamic tests at +125 6 dynamic tests at -55 7 functional tests at +25 8a functional tests at +125 8b functional tests at -55 9 switching tests at +25 10 switching tests at +125 11 switching tests at -55 1
microcircuit data sheet mnclc400a-x rev 2a0 features - -3db bandwidth of 270mhz - 0.05% settling in 12ns - low power, 150mw - low distortion, -60dbc at 20mhz - stable without compensation - overload and short circuit protection - +1 to +8 closed-loop gain range applications - flash, precision a/d conversion - photodiode, ccd preamps - if processors - high-speed communications - line drivers - video distribution - high-speed communications 2
microcircuit data sheet mnclc400a-x rev 2a0 (absolute maximum ratings) (note 1) supply voltage (vs) +7v dc output current (iout) +70ma maximum power dissipation (pd) (note 2) 1.2w junction temperature (tj) +175 c storage temperature range -65 c to +150 c lead temperature (soldering, 10 seconds) +300 c thermal resistance junction-to-ambient (thetaja) 134 c/w ceramic dip (still air) 82 c/w (500 lfpm) tbd lcc (still air) tbd (500 lfpm) junction-to-case (thetajc) 28 c/w ceramic dip tbd lcc package weight (typical) 1070 mg ceramic dip tbd lcc esd tolerance (note 3) 1000 v esd rating note 1: absolute maximum ratings are limits beyond which damage to the device may occur. operating ratings are conditions for which the device is functional, but do not guarantee specific performance limits. for guaranteed specifications and test conditions see the electrical characteristics. the guaranteed specifications apply only for the test conditions listed. some performance characteristics may degrade when the device is not operated under the listed test conditions. note 2: the maximum power dissipation must be derated at elevated temperatures and is dictated by tjmax (maximum junction temperature), thetaja (package junction to ambient thermal resistance), and ta (ambient temperature). the maximum allowable power dissipation at any temperature is pdmax = (tjmax - ta)/thetaja or the number given in the absolute maximum ratings, whichever is lower. note 3: human body model, 100pf discharged through 1.5k ohms. recommended operating conditions supply voltage (vs) +5v dc closed loop gain range +1 to +8 ambient operating temperature range (ta) -55 c to +125 c 3
mnclc400a-x rev 2a0 microcircuit data sheet electrical characteristics dc parameters: open loop characteristics (the following conditions apply to all the following parameters, unless otherwise specified.) dc: rl = 100 ohms, vs = +5v dc. -55 c < ta < +125 c (note 3) symbol parameter conditions notes pin- name min max unit sub- groups +iin input bias current (noninverting) rs = 50ohm -20 +20 ua 1, 2 -36 +36 ua 3 -iin input bias current (inverting) rs = 50ohm -20 +20 ua 1 -30 +30 ua 2 -36 +36 ua 3 vio input offset voltage rs = 50ohm -5 5 mv 1 -9 9 mv 2 -8.2 8.2 mv 3 rol transimpedance ta = +25c 1 30 v/ma 1 is supply current no load +23 ma 1, 2, 3 psrr power supply rejection ratio +vs = +4.5v to +5.5v -vs = -4.5v to -5.5v 45 db 1, 2, 3 +rin input resistance 1 100 kohm 1, 2 1 50 kohm 3 iout output current 1 50 ma 1, 2 1 355 ma 3 cmrr common mode rejection ratio vcm = +2.0v 145 db1 vcm = +1.2v 1 45 db 2, 3 vout output voltage swing no load 1 2.8 v 1, 2 1 2.3 v 3 4
mnclc400a-x rev 2a0 microcircuit data sheet electrical characteristics ac parameters: closed loop characteristics (the following conditions apply to all the following parameters, unless otherwise specified.) ac: rl = 100 ohms, rf = 250 ohms, vs = +5v dc, and av = +2. -55 c < ta < +125 c (note 3) symbol parameter conditions notes pin- name min max unit sub- groups ssbw small signal bandwidth -3db bandwidth, vout < 0.5vpp 150 mhz 4 2 120 mhz 5 2 150 mhz 6 gfpl gain flatness peaking .1 to 40 mhz 0.3 db 4 2 0.4 db 5, 6 gfph gain flatness peaking no peaking over 40mhz 0.5 db 4 2 0.7 db 5, 6 gfr gain flatness rolloff .1 to 75 mhz 1.0 db 4 2 1.3 db 5 2 1.0 db 6 hd2 2nd harmonic distortion 2 vpp at 20 mhz -45 db 4 2 -45 db 5 2 -40 db 6 hd3 3rd harmonic distortion 2 vpp at 20 mhz -50 db 4 2 -50 db 5, 6 ac parameters: time domain response (the following conditions apply to all the following parameters, unless otherwise specified.) ac: rl = 100 ohms, rf = 250 ohms, vs = +5v dc. -55 c < ta < +125 c (note 3) sr slew rate av= +2, measured +1v with +3v step 1 430 v/us 9, 10, 11 trs rise time 0.5v step 1 2.4 ns 9, 10, 11 trl fall time 5v step 1 10 ns 9, 10, 11 ts settling time 2v step at 0.1% of fixed value 1 13 ns 9, 10, 11 2v step at 0.05% of fixed value 1 15 ns 9, 10, 11 os overshoot 0.5v step 1 10 % 9 1 15 % 10, 11 5
mnclc400a-x rev 2a0 microcircuit data sheet electrical characteristics dc parameters: drift values (the following conditions apply to all the following parameters, unless otherwise specified.) dc: rl = 100 ohms, vs = +5v dc. -55 c < ta < +125 c "deltas not required on b-level product. deltas required for s-level (-mls) product as specified on internal processing instructions (ipi)." (note 3) symbol parameter conditions notes pin- name min max unit sub- groups +iin input bias current (noninverting) rs = 50ohm -1.5 1.5 ua 1 -iin input bias current (inverting) rs = 50ohm -1.5 1.5 ua 1 vio input offset voltage rs = 50ohms -1.0 1.0 mv 1 is supply current no load -2.0 2.0 ma 1 note 1: if not tested, shall be guaranteed to the limits specified in table 1 note 2: group a testing only. note 3: the algebraic convention, whereby the most negative value is a minimum and most positive is a maximum, is used in this table. negative current shall be defined as convential current flow out of a device terminal. 6
microcircuit data sheet mnclc400a-x rev 2a0 graphics and diagrams graphics# description 07081hra3 cerdip (j), 8 lead (b/i ckt) 07086hra2 lcc (e), type c, 20 terminal (b/i ckt) e20are lcc (e), type c, 20 terminal(p/p dwg) j08arl cerdip (j), 8 lead (p/p dwg) p000427a cerdip (j), 8 lead (pinout) p000445a lcc (e), type c, 20 terminal (pinout) see attached graphics following this page. 7
n mil/aerospace operations 2900 semiconductor drive santa clara, ca 95050 1 8 2 7 3 6 4 5 clc400j 8 - lead dip top view connection diagram p000427a v inv -v cc +v cc v out offset adjust v non-inv n/c n/c
n mil/aerospace operations 2900 semiconductor drive santa clara, ca 95050 4 18 5 6 7 8 14 9 10 11 12 13 17 16 15 3 2 1 20 19 n/c n/c +v cc n/c v o n/c n/c n/c -v cc n/c clc400e 20 - lead lcc connection diagram top view p000445a v- n/c n/c n/c v+ n/c n/c n/c n/c off adj
microcircuit data sheet mnclc400a-x rev 2a0 revision history rev ecn # rel date originator changes 0a0 m0003157 02/18/99 shaw mead initial mds release 1a0 m0003241 03/09/99 shaw mead thermal data for ceramic dip added. package weight for ceramic dip added. gain range in recommended op. cond. corrected. cmrr subgroups corrected. closed loop gain in ac conditions corrected. rf = 250 ohms added to ac conditions. 2a0 m0003273 03/09/99 shaw mead processing and qci document reference added. conditions for sr added. 8
|
