View CLC411AJ-QML_3254625.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

original creation date: 02/11/99 last update date: 11/04/99 last major revision date: 05/06/99 mnclc411a-x rev 0a0 microcircuit data sheet high-speed video op amp with disable general description the comlinear clc411 combines a state-of-the-art complementary bipolar process with comlinear's patented current-feedback architecture to provide a very high-speed op amp operating from +15v supplies. drawing only 11ma quiescent current, the clc411 provides a 200mhz small signal bandwidth and a 2300v/us slew rate while delivering a continuos 70ma current output with +4.5v output swing. the clc411's high-speed performance includes a 15ns settling time to 0.1%(2v step) and a 2.3ns rise and fall time (6v step). the clc411 is designed to meet the requirements of professional broadcast video systems including composite video and high definition television. the clc411 exceeds the hdtv standard for gain flatness to 30mhz with it's +0.05db flat frequency response and exceeds composite video standards with its very low differential gain and phase errors of 0.02%, 0.03degrees. the clc411 is the op amp of choice for all video systems requiring upward compatibility from ntsc and pal to hdtv. the clc411 features a very fast disable/enable (10ns/55ns) allowing the multiplexing of high-speed signals onto an analog bus through the common output connections of multiple clc411's. using the same signal source to drive disable/enable pins is easy since "break-before-make" is guaranteed. ns part numbers CLC411AJ-QML industry part number clc411a prime die ub1590c controlling document 5962-9456601mpa processing mil-std-883, method 5004 quality conformance inspection mil-std-883, method 5005 subgrp description temp ( c) o 1 static tests at +25 2 static tests at +125 3 static tests at -55 4 dynamic tests at +25 5 dynamic tests at +125 6 dynamic tests at -55 7 functional tests at +25 8a functional tests at +125 8b functional tests at -55 9 switching tests at +25 10 switching tests at +125 11 switching tests at -55 1
microcircuit data sheet mnclc411a-x rev 0a0 features - 200mhz small signal bandwidth (1vpp) - +0.05db gain flatness to 30mhz - 0.02%, 0.03degrees differential gain, phase - 2300v/us slew rate - 10ns disable to high-impedance output - 70ma continuous output current - +4.5v output swing into 100 ohm load - +4.0v input voltage range applications - hdtv amplifier - video line driver - high-speed analog bus driver - video signal multiplexer - dac output buffer 2
microcircuit data sheet mnclc411a-x rev 0a0 (absolute maximum ratings) supply voltage (vs) (note 1) +18 v dc output current (iout) 125 ma maximum power dissipation (pd) (note 2) 1.34w junction temperature (tj) +175c lead temperature (soldering, 10 seconds) +300c differential input voltage (vid) +15 v common mode input voltage (vcm) +vs storage temperature range -65c to +150c thermal resistance thetaja 97 c/w ceramic dip (still air ) 59 c/w ceramic dip (500lf/min air flow) 20 c/w thetajc package weight (typical) tbd ceramic dip esd tolerance (note 3) 1000v esd rating note 1: absolute maximum ratings are limits beyond which damage to the device may occur. operating ratings are conditions for which the device is functional, but do not guarantee specific performance limits. for guaranteed specifications and test conditions see the electrical characteristics. the guaranteed specifications apply only for the test conditions listed. some performance characteristics may degrade when the device is not operated under the listed test conditions. note 2: the maximum power dissipation must be derated at elevated temperatures and is dictated by tjmax (maximum junction temperature), thetaja (package junction to ambient thermal resistance), and ta (ambient temperature). the maximum allowable power dissipation at any temperature is pdmax = (tjmax - ta)/thetaja or the number given in the absolute maximum ratings, whichever is lower. note 3: human body model, 100pf discharged through 1.5k ohms. 3
microcircuit data sheet mnclc411a-x rev 0a0 recommended operating conditions supply voltage (vs) +15vdc gain range (av) +10 to +1000v/v ambient operating temperature range (ta) -55 c to +125 c 4
mnclc411a-x rev 0a0 microcircuit data sheet electrical characteristics static and dc tests. (the following conditions apply to all the following parameters, unless otherwise specified.) dc: vs = +15 v dc, av = +2, rl = 100 ohms, rf = 300 ohms, rg = 300 ohms, -55c < ta < +125 c (note 3) symbol parameter conditions notes pin- name min max unit sub- groups +iib input bias current 030ua1 -20 20 ua 2 065ua3 -iib input bias current -30 30 ua 1, 2 -40 40 ua 3 vio input offset voltage -9 9 mv 1 -14 14 mv 2 -13 13 mv 3 +dib average input bias current drift ta = +125c, -55c 1 -250 250 na/c 2 1 -400 400 na/c 3 -dib average input bias current drift ta = +125c, -55c 1 -150 150 na/c 2 1 -200 200 na/c 3 dvio average input offset voltage drift ta = +125c, -55c 1 -50 50 uv/c 2, 3 icc supply current no load 12 ma 1, 2 14 ma 3 iccd supply current disable 3.5 ma 1 4.5 ma 2, 3 psrr power supply rejection ratio +vs = +4.5 v to +5.0 v, -vs = -4.5 v to -5.0 v 50 db 1 48 db 2, 3 cmrr common mode rejection ration vcm = +1 v 146 db4 1 44 db 5, 6 5
mnclc411a-x rev 0a0 microcircuit data sheet electrical characteristics frequeuncy domain tests. (the following conditions apply to all the following parameters, unless otherwise specified.) ac: vs = +15 v dc, av = +2, rl = 100 ohms, rf = 300 ohms, rg = 300 ohms, -55c < ta < +125 c (note 3) symbol parameter conditions notes pin- name min max unit sub- groups ssbw small signal bandwith -3 db bandwidth, vout < 1.0 vpp 150 mhz 4 2 110 mhz 5 2 150 mhz 6 lsbw large signal bandwith -3 db bandwidth, vout < 6.0 vpp 1 50 mhz 4, 6 1 40 mhz 5 gfph gain flatness peaking high 0.1 mhz to 200 mhz, vout < 1.0 vpp 0.5 db 4 2 0.6 db 5, 6 gfpl gain flatness peaking low 0.1 mhz to 30 mhz, vout < 1.0 vpp 0.2 db 4 2 0.3 db 5 2 0.2 db 6 gfrl gain flatness rolloff low 0.1 mhz to 30 mhz, vout < 1.0 vpp 0.2 db 4 2 0.4 db 5 2 0.2 db 6 gfrh gain flatness rolloff high 0.1 mhz to 60 mhz, vout < 1.0 vpp 0.4 db 4 2 0.7 db 5, 6 lpd linear phase deviation 0.1 mhz to 60 mhz, vout < 1.0 vpp 1 1.0 deg 4, 5, 6 distortion and noise tests. (the following conditions apply to all the following parameters, unless otherwise specified.) ac: vs = +15 v dc, av = +2, rl = 100 ohms, rf = 300 ohms, rg = 300 ohms, -55c < ta < +125 c (note 3) hd2 second harmonic distortion 2 vpp at 20 mhz -35 dbc 4 2 -35 dbc 5, 6 hd3 third harmonic distortion 2 vpp at 20 mhz -42 dbc 4 2 -35 dbc 5 2 -42 dbc 6 6
mnclc411a-x rev 0a0 microcircuit data sheet electrical characteristics timing tests. (the following conditions apply to all the following parameters, unless otherwise specified.) ac: vs = +15 v dc, av = +2, rl = 100 ohms, rf = 300 ohms, rg = 300 ohms, -55c < ta < +125 c (note 3) symbol parameter conditions notes pin- name min max unit sub- groups ts settling time 2 v step at 0.1% of the fixed value 1 18 ns 9 1 23 ns 10, 11 os overshoot 2.0 v step 1 10 % 9 1 15 5 10, 11 miscellaneous performance tests. (the following conditions apply to all the following parameters, unless otherwise specified.) dc: vs = +15 v dc, av = +2, rl = 100 ohms, rf = 300 ohms, rg = 300 ohms, -55c < ta < +125 c (note 3) rin input resistance 1 750 kohms 1 1 1000 kohms 2 1 250 kohms 3 cin input capacitance 1 3 pf 1, 2, 3 vout output voltage range no load, ta = +25c 1 -4.5 4.5 v 1 voutl output voltage range rl = 100ohms, ta = +25c 1 -4.0 4.0 v 1 cmir common mode input voltage range ta = +25c 1 -3.5 3.5 v 1 iout output current 1 50 ma 1 140 ma2 130 ma3 disable and enable tests. (the following conditions apply to all the following parameters, unless otherwise specified.) dc: vs = +15 v dc, av = +2, rl = 100 ohms, rf = 300 ohms, rg = 300 ohms, -55c < ta < +125 c (note 3) toff disable time to > 50 db attenuation at 10 mhz 1 30 ns 9, 11 160ns10 vdis voltage at /dis pin to disable 1 3.0 v 1, 2, 3 ven voltage at /dis pin to enable 1 6.5 v 1, 2 1 7.0 v 3 osd off isolation at 10 mhz 1 55 db 4, 5, 6 note 1: if not tested, shall be guaranteed to the limits specified. note 2: group a testing only. 7
mnclc411a-x rev 0a0 microcircuit data sheet (continued) note 3: the algebraic convention, whereby the most negative value is a minimum and the most positive is a maximum, is used in this table. negative current shall be defined as conventional current flow out of a device terminal. 8
microcircuit data sheet mnclc411a-x rev 0a0 graphics and diagrams graphics# description 07087hra2 cerdip (j), 8 lead (b/i ckt) j08arl cerdip (j), 8 lead (p/p dwg) p000417a cerdip (j), 8 lead (pinout) see attached graphics following this page. 9

n mil/aerospace operations 2900 semiconductor drive santa clara, ca 95050 1 8 2 7 3 6 4 5 clc411j 8 - lead dip top view connection diagram p000417a +vr v inv v non-inv -v cc -vr v out +v cc dis
microcircuit data sheet mnclc411a-x rev 0a0 revision history rev ecn # rel date originator changes 0a0 m0003592 11/04/99 shaw mead initial mds release 10

▲Up To Search▲

Price & Availability of CLC411AJ-QML

	To Download CLC411AJ-QML Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .