View HYB18T1G160BF-25F_3319031.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

may 2007 hy[b/i]18t1g400b[f/c](l) hy[b/i]18t1g800b[f/c](l) hy[b/i]18t1g160b[f/c](l) 1-gbit double-data-rate-two sdram ddr2 sdram rohs compliant products internet data sheet rev. 1.2
we listen to your comments any information within this document that yo u feel is wrong, unclear or missing at all? your feedback will help us to continuous ly improve the quality of this document. please send your proposal (including a reference to this document) to: techdoc@qimonda.com internet data sheet hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram qag_techdoc_rev400 / 3.2 qag / 2006-07-21 2 03062006-znh8-hurv hy[b/i]18t1g400b[f/c](l), hy[b/i]18t1g160b[f/c](l), hy[b/i]18t1g800b[f/c](l) revision history: 2007-05, rev. 1.2 page subjects (major chan ges since last revision) all adapted internet edition added products with industrial temperature range added hyb18t1g400bfl-3s, hyb18t1g800bfl-3s , hyb18t1g160bfl-3s, hyb18t1g400bfl-25f, hyb18t1g800bfl-25f, hyb18t1g160bfl-25f previous revision: 2007-03, rev. 1.1
internet data sheet rev. 1.2, 2007-05 3 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram 1overview this chapter gives an overview of the 1-gbit double-dat a-rate-two sdram product family and describes its main characteristics. 1.1 features the 1-gbit double-data-rate sdram offers the following key features: ? 1.8 v 0.1 v power supply 1.8 v 0.1 v (sstl_18) compatible i/o ? dram organizations with 4, 8 and 16 data in/outputs ? double data rate architectu re: two data transfers per clock cycle four internal ban ks for concurrent operation ? programmable cas latency: 3, 4, 5 and 6 ? programmable burst length: 4 and 8 ? differential clock inputs (ck and ck ) ? bi-directional, differentia l data strobes (dqs and dqs ) are transmitted / received with da ta. edge aligned with read data and center-aligned with write data ? dll aligns dq and dqs transitions with clock ?dqs can be disabled for single-ended data strobe operation ? commands entered on each positive clock edge, data and data mask are referenced to both edges of dqs ? data masks (dm) for write data ? posted cas by programmable additive latency for better command and data bus efficiency ? off-chip-driver impedance adjustment (ocd) and on- die-termination (odt) for better signal quality ? auto-precharge operation for read and write bursts ? auto-refresh, self-refresh and power saving power- down modes ? average refresh period 7.8 s at a t case lower than 85 c, 3.9 s between 85 c and 95 c ? programmable self refres h rate via emrs2 setting ? programmable partial array refresh via emrs2 settings ? dcc enabling via emrs2 setting ? full and reduced strengt h data-output drivers ? 1k page size for 4 & 8, 2k page size for 16 ? package: p(g)-tfbga-6 8 and p(g)-tfbga-84 ? rohs compliant products 1) ? all speed grades faster than ddr2?400 comply with ddr2?400 timing specifications when run at a clock rate of 200 mhz. table 1 performance tabl es for ?2.5(f) 1) rohs compliant product: restriction of the use of certain hazar dous substances (rohs) in el ectrical and electronic equipment as defined in the directive 2002/95/ec issued by the european parliament and of the council of 27 january 2003. these substances include m ercury, lead, cadmium, hexavalent chromium, polybro minated biphenyls and polybrominated biphenyl ethers. product type speed code ?2.5f ?2.5 unit speed grade ddr2?800d 5?5?5 ddr2?800e 6?6?6 ? max. clock frequency @cl6 f ck6 400 400 mhz @cl5 f ck5 400 333 mhz @cl4 f ck4 266 266 mhz @cl3 f ck3 200 200 mhz min. ras-cas-delay t rcd 12.5 15 ns min. row precharge time t rp 12.5 15 ns min. row active time t ras 45 45 ns min. row cycle time t rc 57.5 60 ns
internet data sheet rev. 1.2, 2007-05 4 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram table 2 performance table for ?3(s) table 3 performance table for ?3.7 table 4 performance table for ?5 product type speed code ?3 ?3s unit speed grade ddr2?667c 4?4?4 ddr2?667d 5?5?5 ? max. clock frequency @cl5 f ck5 333 333 mhz @cl4 f ck4 333 266 mhz @cl3 f ck3 200 200 mhz min. ras-cas-delay t rcd 12 15 ns min. row precharge time t rp 12 15 ns min. row active time t ras 45 45 ns min. row cycle time t rc 57 60 ns product type speed code ?3.7 unit speed grade ddr2?533c 4?4?4 ? max. clock frequency @cl5 f ck5 266 mhz @cl4 f ck4 266 mhz @cl3 f ck3 200 mhz min. ras-cas-delay t rcd 15 ns min. row precharge time t rp 15 ns min. row active time t ras 45 ns min. row cycle time t rc 60 ns product type speed code ?5 units speed grade ddr2?400b 3?3?3 ? max. clock frequency @cl5 f ck5 200 mhz @cl4 f ck4 200 mhz @cl3 f ck3 200 mhz min. ras-cas-delay t rcd 15 ns min. row precharge time t rp 15 ns min. row active time t ras 40 ns min. row cycle time t rc 55 ns
internet data sheet rev. 1.2, 2007-05 5 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram 1.2 description the 1-gbit ddr2 dram is a high-speed double-data-rate- two cmos synchronous dram device, containing 1,073,741,824 bits and internally configured as anoctal quadbank dram. the 1-gbit device is organized as either 32 mbit 4 i/o 8 banks, 16 mbit 8 i/o 8 banks or 8 mbit 16 i/o 8 banks chip. these devices achieve high speed transfer rates starting at 400 mb/sec/pin for general applications. the device is designed to comply with all ddr2 sdram key features: 1. posted cas with additive latency, 2. write latency = read latency - 1, 3. normal and weak strength data-output driver, 4. off-chip driver (ocd) impedance adjustment 5. on-die termination (odt) function. all of the control and address inputs are synchronized with a pair of externally supplied differential clocks. inputs are latched at the cross poi nt of differential clocks (ck rising and ck falling). all i/os are synchronized with a single ended dqs or differential dqs-dqs pair in a source synchronous fashion. a 17-bit address bus for 4 and 8 organised components and a 16 bit address bus for 16 components is used to convey row, column and bank address information in a ras - cas multiplexing style. the ddr2 device operates with a 1.8 v 0.1 v power supply. an auto-refresh and self-refresh mode is provided along with various power-saving power-down modes. the functionality described and the timing specifications included in this data sheet are for the dll enabled mode of operation. the ddr2 sdram is available in p(g)-tfbga-68 and p(g)- tfbga-84 packages.
internet data sheet rev. 1.2, 2007-05 6 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram table 5 ordering information for lead-free products (rohs compliant) product type org. speed cas-rcd-rp latencies 1)2)3) clock (mhz) package note standard temperature range (0 c - +70 c) hyb18t1g400bf-2.5f 4 ddr2-800d 5-5-5 400 pg-tfbga-68 4) hyb18t1g800bf-2.5f 8 hyb18t1g160bf-2.5f 16 pg-tfbga-84 hyb18t1g400bf-2.5 4 ddr2-800e 6-6-6 400 pg-tfbga-68 hyb18t1g800bf-2.5 8 hyb18t1g160bf-2.5 16 pg-tfbga-84 hyb18t1g400bf-3 4 ddr2-667c 4-4-4 333 pg-tfbga-68 hyb18t1g800bf-3 8 hyb18t1g160bf-3 16 pg-tfbga-84 hyb18t1g400bf-3s 4 ddr2-667d 5-5-5 333 pg-tfbga-68 hyb18t1g400bfl-3s 4 hyb18t1g800bf-3s 8 hyb18t1g800bfl-3s 8 hyb18t1g160bf-3s 16 pg-tfbga-84 hyb18t1g160bfl-3s 16 hyb18t1g400bf-3.7 4 ddr2-533c 4-4-4 266 pg-tfbga-68 hyb18t1g400bfl-3.7 4 hyb18t1g800bf-3.7 8 hyb18t1g800bfl-3.7 8 hyb18t1g160bf-3.7 16 pg-tfbga-84 hyb18t1g160bfl-3.7 16 hyb18t1g400bf-5 4 ddr2-400b 3-3-3 200 pg-tfbga-68 hyb18t1g400bfl-5 4 hyb18t1g800bf-5 8 hyb18t1g800bfl-5 8 hyb18t1g160bf-5 16 pg-tfbga-84 hyb18t1g160bfl-5 16
internet data sheet rev. 1.2, 2007-05 7 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram table 6 ordering information for lead-containing products industrial temperature range (?40 c - +85 c) hyi18t1g400bf-2.5f 4 ddr2-800d 5-5-5 400 pg-tfbga-68 4) hyi18t1g800bf-2.5f 8 hyi18t1g160bf-2.5f 16 pg-tfbga-84 hyi18t1g400bf-2.5 4 ddr2-800e 6-6-6 400 pg-tfbga-68 hyi18t1g800bf-2.5 8 hyi18t1g160bf-2.5 16 pg-tfbga-84 hyi18t1g400bf-3 4 ddr2-667c 4-4-4 333 pg-tfbga-68 hyi18t1g800bf-3 8 hyi18t1g160bf-3 16 pg-tfbga-84 hyi18t1g400bf-3s 4 ddr2-667d 5-5-5 333 pg-tfbga-68 hyi18t1g800bf-3s 8 hyi18t1g160bf-3s 16 pg-tfbga-84 hyi18t1g400bf-3.7 4 ddr2-533c 4-4-4 266 pg-tfbga-68 hyi18t1g800bf-3.7 8 hyi18t1g160bf-3.7 16 pg-tfbga-84 hyi18t1g400bf-5 4 ddr2-400b 3-3-3 200 pg-tfbga-68 hyi18t1g800bf-5 8 hyi18t1g160bf-5 16 pg-tfbga-84 1) cas: column address strobe 2) rcd: row column delay 3) rp: row precharge 4) rohs compliant product: restriction of the use of certain hazar dous substances (rohs) in el ectrical and electronic equipment as defined in the directive 2002/95/ec issued by the european parliament and of the council of 27 january 2003. these substances include m ercury, lead, cadmium, hexavalent chromium, polybro minated biphenyls and polybrominated biphenyl ethers. product type org. speed cas-rcd-rp latencies 1)2)3) clock (mhz) package standard temperature range (0 c - +70 c) hyb18t1g400bc-2.5f 4 ddr2-800d 5-5-5 400 p-tfbga-68 hyb18t1g800bc-2.5f 8 hyb18t1g160bc-2.5f 16 p-tfbga-84 hyb18t1g400bc-2.5 4 ddr2-800e 6-6-6 400 p-tfbga-68 hyb18t1g800bc-2.5 8 hyb18t1g160bc-2.5 16 p-tfbga-84 hyb18t1g400bc-3 4 ddr2-667c 4-4-4 333 p-tfbga-68 hyb18t1g800bc-3 8 hyb18t1g160bc-3 16 p-tfbga-84 product type org. speed cas-rcd-rp latencies 1)2)3) clock (mhz) package note
internet data sheet rev. 1.2, 2007-05 8 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram note: for product nomenclature see chapter 9 of this data sheet hyb18t1g400bc-3s 4 ddr2-667d 5-5-5 333 p-tfbga-68 hyb18t1g800bc-3s 8 hyb18t1g160bc-3s 16 p-tfbga-84 hyb18t1g400bc-3.7 4 ddr2-533c 4-4-4 266 p-tfbga-68 hyb18t1g800bc-3.7 8 hyb18t1g160bc-3.7 16 p-tfbga-84 hyb18t1g400bc-5 4 ddr2-400b 3-3-3 200 p-tfbga-68 hyb18t1g800bc-5 8 hyb18t1g160bc-5 16 p-tfbga-84 industrial temperature range (?40 c - +85 c) hyi18t1g400bc-2.5f 4 ddr2-800d 5-5-5 400 p-tfbga-68 hyi18t1g800bc-2.5f 8 hyi18t1g160bc-2.5f 16 p-tfbga-84 hyi18t1g400bc-2.5 4 ddr2-800e 6-6-6 400 p-tfbga-68 hyi18t1g800bc-2.5 8 hyi18t1g160bc-2.5 16 p-tfbga-84 hyi18t1g400bc-3 4 ddr2-667c 4-4-4 333 p-tfbga-68 hyi18t1g800bc-3 8 hyi18t1g160bc-3 16 p-tfbga-84 hyi18t1g400bc-3s 4 ddr2-667d 5-5-5 333 p-tfbga-68 hyi18t1g800bc-3s 8 hyi18t1g160bc-3s 16 p-tfbga-84 hyi18t1g400bc-3.7 4 ddr2-533c 4-4-4 266 p-tfbga-68 hyi18t1g800bc-3.7 8 hyi18t1g160bc-3.7 16 p-tfbga-84 hyi18t1g400bc-5 4 ddr2-400b 3-3-3 200 p-tfbga-68 hyi18t1g800bc-5 8 hyi18t1g160bc-5 16 p-tfbga-84 1) cas: column address strobe 2) rcd: row column delay 3) rp: row precharge product type org. speed cas-rcd-rp latencies 1)2)3) clock (mhz) package
internet data sheet rev. 1.2, 2007-05 9 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram 2 configuration this chapter contains the chip configuration and addressing. 2.1 chip configuration for pg-tfbga-68 the chip configuration of a ddr2 sdram is listed by function in table 7 . the abbreviations used in the ball# and buffer type columns are explained in table 8 and table 9 respectively. the ball numbering for the fbga package is depicted in figures. table 7 chip configuration of ddr2 sdram ball# name ball type buffer type function clock signals 4 8 organizations j8 ck i sstl clock signal ck, ck k8 ck i sstl k2 cke i sstl clock enable control signals 4 8 organizations k7 ras i sstl row address strobe (ras ), column addr ess strobe (cas ), write enable (we ) l7 cas i sstl k3 we i sstl l8 cs i sstl chip select address signals 4 8 organizations l2 ba0 i sstl bank address bus 1:0 l3 ba1 i sstl l1 ba2 i sstl bank address bus 2 note: 1 gbit components and higher
internet data sheet rev. 1.2, 2007-05 10 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram m8 a0 i sstl address signal 12:0, address signal 10/autoprecharge m3 a1 i sstl m7 a2 i sstl n2 a3 i sstl n8 a4 i sstl n3 a5 i sstl n7 a6 i sstl p2 a7 i sstl p8 a8 i sstl p3 a9 i sstl m2 a10 i sstl ap i sstl p7 a11 i sstl r2 a12 i sstl r8 a13 i sstl address signal 13 note: 1 gbit 4/ 8 components data signals 4 8 organizations g8 dq0 i/o sstl data signal 3:0 note: dq[3:0] for 4 components dq[7:0] for 8 components g2 dq1 i/o sstl h7 dq2 i/o sstl h3 dq3 i/o sstl h1 dq4 i/o sstl data signal 7:4 h9 dq5 i/o sstl f1 dq6 i/o sstl f9 dq7 i/o sstl data strobe 4 8 organizations f7 dqs i/o sstl data strobe e8 dqs i/o sstl data strobe 8 organizations f3 rdqs o sstl read data strobe e2 rdqs o sstl data mask 4 8 organizations f3 dm i sstl data mask power supplies 4 8 organizations e9, g1, g3, g7, g9 v ddq pwr ? i/o driver power supply e1, j9, m9, r1 v dd pwr ? power supply e7, f2, f8, h2, h8 v ssq pwr ? i/o driver power supply e3, j3, n1, p9 v ss pwr ? power supply j2 v ref al ? i/o reference voltage ball# name ball type buffer type function
internet data sheet rev. 1.2, 2007-05 11 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram table 8 abbreviations for ball type table 9 abbreviations for buffer type j1 v ddl pwr ? power supply j7 v ssdl pwr ? power supply not connected 4 organizations a1, a2, a8, a9, e2, f9, h1,f1, r7, h9, w1, w2, w8, w9, r3 nc nc ? not connected not connected 8 organization a1, a2, a8, a9, r7, w1, w2, w8, w9, r3 nc nc ? not connected other balls 4 8 organizations k9 odt i sstl on-die termination control abbreviation description i standard input-only ball. digital levels. o output. digital levels. i/o i/o is a bidirectio nal input/output signal. ai input. analog levels. pwr power gnd ground nc not connected abbreviation description sstl serial stub terminated logic (sstl_18) lv-cmos low voltage cmos cmos cmos levels od open drain. the corresponding ball has 2 operat ional states, active low and tristate, and allows multiple devices to share as a wire-or. ball# name ball type buffer type function
internet data sheet rev. 1.2, 2007-05 12 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram figure 1 ball configuration for 4 components, pg-tfbga-68 (top view) note: v ddl and v ssdl are power and ground for the dll. v ddl is connected to v dd on the device. v dd , v ddq , v ssdl , v ss and v ssq are isolated on the device. 0337 $ % & ' ) * + - ( / . &6 $ $ $ '4 '46 9 66'/ 9 664 9 ''4 9 664 $ 1& $ 9 ''4 1& '4 1& &. &$6 '46 9 ''4 9 664 &. 9 '' 5$6 2'7 9 '' $ 9 66 1&$ %$ 1& 1& 9 5() 1& $$3 $ $ $ $ $ $ 1& '4 '0 9 66 9 '' 9 664 9 ''4 '4 9 ''4 9 664 9 ''/ 9 66 &.( :( %$ %$ 9 66 9 '' 0 1 3 5 7 8 9 : 1& 1& 1& 1& 1& 1& 1& 1&
internet data sheet rev. 1.2, 2007-05 13 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram figure 2 ball configuration for 8 components, pg-tfbga-68 (top view) notes 1. rdqs / rdqs are enabled by emrs(1) command. 2. if rdqs / rdqs is enabled, the dm function is disabled 3. when enabled, rdqs & rdqs are used as strobe signals during reads. 4. v ddl and v ssdl are power and ground for the dll. they are connected on the device from v dd , v ddq , v ss and v ssq . 0337 &6 %$ '4 '4 9 5() 18 5'46 $$3 $ $ $ $ $ $ 1& '4 '0 5'46 9 66 $ $ $ '4 '46 9 66'/ 9 664 9 ''4 9 664 $ 1& $ 9 ''4 '4 '4 '4 $ % & ' ) * + - ( / . 9 '' 9 664 9 ''4 '4 9 ''4 9 664 9 ''/ 9 66 &.( :( &. %$ %$ 9 66 9 '' &$6 '46 9 ''4 9 664 &. 9 '' 5$6 2'7 9 '' $ 9 66 1&$ 0 1 3 5 7 8 9 : 1& 1& 1& 1& 1& 1& 1& 1&
internet data sheet rev. 1.2, 2007-05 14 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram 2.2 chip configuration for pg-tfbga-84 the chip configuration of a ddr2 sdram is listed by function in table 10 . the abbreviations used in the ball#/buffer type columns are explained in table 11 and table 12 respectively. table 10 chip configuration of ddr sdram ball# name ball type buffer type function clock signals 16 organization j8 ck i sstl clock signal ck, ck k8 ck i sstl k2 cke i sstl clock enable control signals 16 organization k7 ras i sstl row address strobe (ras), column address strobe (cas), write enable (we) l7 cas i sstl k3 we i sstl l8 cs i sstl chip select address signals 16 organization l2 ba0 i sstl bank address bus 2:0 note: 1 gbit components and higher l3 ba1 i sstl l1 ba2 i sstl m8 a0 i sstl address signal 12:0, address signal 10/autoprecharge m3 a1 i sstl m7 a2 i sstl n2 a3 i sstl n8 a4 i sstl n3 a5 i sstl n7 a6 i sstl p2 a7 i sstl p8 a8 i sstl p3 a9 i sstl m2 a10 i sstl ap i sstl p7 a11 i sstl r2 a12 i sstl
internet data sheet rev. 1.2, 2007-05 15 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram data signals 16 organization g8 dq0 i/o sstl data signal 15:0 note: dq[15:0] for 16 components g2 dq1 i/o sstl h7 dq2 i/o sstl h3 dq3 i/o sstl h1 dq4 i/o sstl h9 dq5 i/o sstl f1 dq6 i/o sstl f9 dq7 i/o sstl c8 dq8 i/o sstl c2 dq9 i/o sstl d7 dq10 i/o sstl d3 dq11 i/o sstl d1 dq12 i/o sstl d9 dq13 i/o sstl b1 dq14 i/o sstl b9 dq15 i/o sstl data strobe 16 organization b7 udqs i/o sstl data strobe upper byte a8 udqs i/o sstl f7 ldqs i/o sstl data strobe lower byte e8 ldqs i/o sstl data mask 16 organization b3 udm i sstl data mask upper byte f3 ldm i sstl data mask lower byte power supplies 16 organization j2 v ref ai ? i/o reference voltage c1, c3, c7, c9, e9, g1, g3, g7, g9, a9 v ddq pwr ? i/o driver power supply j1 v ddl pwr ? power supply a1, e1, j9, m9, r1 v dd pwr ? power supply a7, d2, d8, e7, f2, f8, h2, h8 v ssq pwr ? power supply j7 v ssdl pwr ? power supply a3, e3, j3, n1, p9 v ss pwr ? power supply ball# name ball type buffer type function
internet data sheet rev. 1.2, 2007-05 16 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram table 11 abbreviations for ball type table 12 abbreviations for buffer type not connected 16 organization a2, e2, r3, r7, r8 nc nc ? not connected other balls 16 organization k9 odt i sstl on-die termination control abbreviation description i standard input-only ball. digital levels. o output. digital levels. i/o i/o is a bidirectio nal input/output signal. ai input. analog levels. pwr power gnd ground nc not connected abbreviation description sstl serial stub terminated logic (sstl_18) lv-cmos low voltage cmos cmos cmos levels od open drain. the corresponding ball has 2 operat ional states, active low and tristate, and allows multiple devices to share as a wire-or. ball# name ball type buffer type function
internet data sheet rev. 1.2, 2007-05 17 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram figure 3 chip configuration for x16 components in pg?tfbga?84 (top view) 03%7 9 '' 1& $ 9 664 1& 9 66 &.( &. 9 66 8'0 '4 9 ''4 '4 '4 9 66 9 ''/ $ 9 664 '4 /'46 5$6 9 '' $ % & ' ) * + - ( / 0 . 1 '4 9 '' %$ %$ $$3 $ 9 66 9 ''4 '4 '4 966'/ $ $ $ '4 1& 9 '' 1& 3 5 $ $ $ $ 1& 9 66 '4 9 ''4 9 664 '4 /'0 9 ''4 9 ''4 '4 9 664 '4 9 5() :( %$ $ $ 8'46 8'46 '4 9 ''4 9 ''4 '4 9 664 '4 9 664 9 ''4 /'46 9 664 9 ''4 '4 9 ''4 9 664 &. 9 '' 2'7 &$6 &6 9 664 9 664
internet data sheet rev. 1.2, 2007-05 18 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram 2.3 1-gbit ddr2 addressing this chapter describes the 1-gbit ddr2 addressing. table 13 ddr2 addressing for 4 organization table 14 ddr2 addressing for 8 organization configuration 256mb x 4 1) 1) referred to as ?org? note bank address ba[2:0] number of banks 8 auto-precharge a10 / ap row address a[13:0] column address a11, a[9:0] number of column address bits 11 2) 2) referred to as ?colbits? number of i/os 4 page size [bytes] 1024 (1k) 3) 3) pagesize = 2 colbits org/8 [bytes] configuration 128mb x 8 1) 1) referred to as ?org? note bank address ba[2:0] number of banks 8 auto-precharge a10 / ap row address a[13:0] column address a[9:0] number of column address bits 10 2) 2) referred to as ?colbits? number of i/os 8 page size [bytes] 1024 (1k) 3) 3) pagesize = 2 colbits org/8 [bytes]
internet data sheet rev. 1.2, 2007-05 19 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram table 15 ddr2 addressing for 16 organization configuration 64mb x 16 1) 1) referred to as ?org? note bank address ba[2:0] number of banks 8 auto-precharge a10 / ap row address a[12:0] column address a[9:0] number of column address bits 10 2) 2) referred to as ?colbits? number of i/os 16 page size [bytes] 2048 (2k) 3) 3) pagesize = 2 colbits org/8 [bytes]
internet data sheet rev. 1.2, 2007-05 20 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram 3 functional description this chapter contains the functional description. table 16 mode register definition (ba[2:0] = 000b) field bits type 1) description ba2 16 reg. addr. bank address [2] note: ba2 not available on 256 mbit and 512 mbit components 0 b ba2 bank address ba1 15 bank address [1] 0 b ba1 bank address ba0 14 bank address [0] 0 b ba0 bank address a13 13 address bus[13] note: a13 is not available for 256 mb it and x16 512 mbit configuration 0 b a13 address bit 13 pd 12 w active power-down mode select 0 b pd fast exit 1 b pd slow exit wr [11:9] w write recovery 2) note: all other bit combinations are illegal. 001 b wr 2 010 b wr 3 011 b wr 4 100 b wr 5 101 b wr 6 dll 8 w dll reset 0 b dll no 1 b dll yes tm 7 w test mode 0 b tm normal mode 1 b tm vendor specific test mode 03%7 %$ %$ %$ $ $ $ $ $ $ $ $ $ $ $ $ $ $ 3' :5 %/ uhjdggu z z zzzz '// 70 &/ %7 z
internet data sheet rev. 1.2, 2007-05 21 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram table 17 extended mode register definition (ba[2:0] = 001 b ) cl [6:4] w cas latency note: all other bit combinations are illegal. 011 b cl 3 100 b cl 4 101 b cl 5 110 b cl 6 111 b cl 7 bt 3 w burst type 0 b bt sequential 1 b bt interleaved bl [2:0] w burst length note: all other bit combinations are illegal. 010 b bl 4 011 b bl 8 1) w = write only register bits 2) number of clock cycles for write recovery during auto- precharge. wr in clock cycles is calculated by dividing t wr (in ns) by t ck (in ns) and rounding up to the next integer: wr [cycles] t wr (ns) / t ck (ns). the mode register must be progra mmed to fulfill the minimum requirement for the analogue t wr timing wr min is determined by t ck.max and wr max is determined by t ck.min . field bits type 1) description ba2 16 reg. addr. bank address [2] note: ba2 not available on 256 mbit and 512 mbit components 0 b ba2 bank address ba1 15 bank address [1] 0 b ba1 bank address ba0 14 bank address [0] 1 b ba0 bank address a13 13 w address bus [13] note: a13 is not available for 256 mbit and x16 512 mbit configuration 0 b a13 address bit 13 qoff 12 w output disable 0 b qoff output buffers enabled 1 b qoff output buffers disabled field bits type 1) description 0 3 % 7 % $ % $ % $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ 4 r i i 5 ' 4 6 ' 4 6 2 & ' 3 u r j u d p 5 w w $/ 5 w w ' , & ' // u h j d g g u z z z z z z z z
internet data sheet rev. 1.2, 2007-05 22 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram rdqs 11 w read data strobe output (rdqs, rdqs ) 0 b rdqs disable 1 b rdqs enable dqs 10 w complement data strobe (dqs output) 0 b dqs enable 1 b dqs disable ocd program [9:7] w off-chip driver calibration program 000 b ocd ocd calibration mode exit, maintain setting 001 b ocd drive (1) 010 b ocd drive (0) 100 b ocd adjust mode 111 b ocd ocd calibration default al [5:3] w additive latency note: all other bit combinations are illegal. 000 b al 0 001 b al 1 010 b al 2 011 b al 3 100 b al 4 101 b al 5 r tt 6,2 w nominal termination resistance of odt note: see table 28 ?odt dc electrical characteristics? on page 30 00 b rtt (odt disabled) 01 b rtt 75 ohm 10 b rtt 150 ohm 11 b rtt 50 ohm dic 1 w off-chip driver im pedance control 0 b dic full (driver size = 100%) 1 b dic reduced dll 0 w dll enable 0 b dll enable 1 b dll disable 1) w = write only register bits field bits type 1) description
internet data sheet rev. 1.2, 2007-05 23 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram table 18 emrs(2) programming extended mode register definition (ba[2:0]=010 b ) field bits type 1) description ba2 16 w bank address note: ba2 is not available on 256 mbit and 512 mbit components 0 b ba2 bank address ba [15:14] w bank adress 00 b ba mrs 01 b ba emrs(1) 10 b ba emrs(2) 11 b ba emrs(3): reserved a[13:8]w address bus note: a13 is not available for 256 mbit and x16 512 mbit configuration 000000 b a address bits srf 7 w address bus, high temperature self refresh rate for t case > 85 c 0 b a7 disable 1 b a7 enable 2) a [6:4] w address bus 000 b a address bits dcc 3 w address bus, duty cycle correction (dcc) 0 b a3 dcc disabled 1 b a3 dcc enabled partial self refresh for 4 banks pasr [2:0] w address bus, partial array self refresh for 4 banks 3) note: only for 256 mbit and 512 mbit components 000 b pasr0 full array 001 b pasr1 half array (ba[1:0]=00, 01) 010 b pasr2 quarter array (ba[1:0]=00) 011 b pasr3 not defined 100 b pasr4 3/4 array (ba[1:0]=01, 10, 11) 101 b pasr5 half array (ba[1:0]=10, 11) 110 b pasr6 quarter array (ba[1:0]=11) 111 b pasr7 not defined 03%7 %$ %$ %$ $ $ $ $ $ $ $ $ $ $ $ $ $ $ uhjdggu 65) '&& 3$65
internet data sheet rev. 1.2, 2007-05 24 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram table 19 emr(3) programming extended mode register definition(ba[2:0]=011 b ) partial self refresh for 8 banks pasr [2:0] w address bus, partial array self refresh for 8 banks 3) note: only for 1g and 2g components 000 b pasr0 full array 001 b pasr1 half array (ba[2:0]=000, 001, 010 & 011) 010 b pasr2 quarter array (b a[2:0]=000, 001) 011 b pasr3 1/8 array (ba[2:0] = 000) 100 b pasr4 3/4 array (ba[2:0]= 010, 011, 100, 101, 110 & 111) 101 b pasr5 half array (ba[2: 0]=100, 101, 110 & 111) 110 b pasr6 quarter array (ba[2:0]= 110 & 111) 111 b pasr7 1/8 array(ba[2:0]=111) 1) w = write only 2) when dram is operated at 85 c t case 95 c the extended self refresh rate must be enabled by setting bit a7 to "1" before the self refresh mode can be entered. 3) if pasr (partial array self refresh) is enabled, data located in areas of the array beyond the specified location will be los t if self refresh is entered. data integrity will be maintained if t ref conditions are met and no self refresh command is issued field bits type 1) 1) w = write only description ba2 16 reg.addr bank address[2] note: ba2 is not available on 256 mbit and 512 mbit components 0 b ba2 bank address ba1 15 bank adress[1] 1 b ba1 bank address ba0 14 bank adress[0] 1 b ba0 bank address a [13:0] w address bus[13:0] note: a13 is not available for 256 mbit and x16 512 mbit configuration 00000000000000 b a[13:0] address bits field bits type 1) description 0 3 % 7 % $ % $ % $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ u h j d g g u
internet data sheet rev. 1.2, 2007-05 25 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram table 20 odt truth table note: x = don?t care; 0 = bit set to low; 1 = bit set to high input pin emrs(1) address bit a10 emrs(1) address bit a11 4 components dq[3:0] x dqs x dqs 0x dm x 8 components dq[7:0] x dqs x dqs 0x rdqs x 1 rdqs 01 dm x 0 16 components dq[7:0] x dq[15:8] x ldqs x ldqs 0x udqs x udqs 0x ldm x udm x
internet data sheet rev. 1.2, 2007-05 26 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram table 21 burst length and sequence burst length starting address (a2 a1 a0) sequential addressing (decimal) interleave addressing (decimal) 4 0 0 0, 1, 2, 3 0, 1, 2, 3 0 1 1, 2, 3, 0 1, 0, 3, 2 1 0 2, 3, 0, 1 2, 3, 0, 1 1 1 3, 0, 1, 2 3, 2, 1, 0 8 0 0 0 0, 1, 2, 3, 4, 5, 6, 7 0, 1, 2, 3, 4, 5, 6, 7 0 0 1 1, 2, 3, 0, 5, 6, 7, 4 1, 0, 3, 2, 5, 4, 7, 6 0 1 0 2, 3, 0, 1, 6, 7, 4, 5 2, 3, 0, 1, 6, 7, 4, 5 0 1 1 3, 0, 1, 2, 7, 4, 5, 6 3, 2, 1, 0, 7, 6, 5, 4 1 0 0 4, 5, 6, 7, 0, 1, 2, 3 4, 5, 6, 7, 0, 1, 2, 3 1 0 1 5, 6, 7, 4, 1, 2, 3, 0 5, 4, 7, 6, 1, 0, 3, 2 1 1 0 6, 7, 4, 5, 2, 3, 0, 1 6, 7, 4, 5, 2, 3, 0, 1 1 1 1 7, 4, 5, 6, 3, 0, 1, 2 7, 6, 5, 4, 3, 2, 1, 0
internet data sheet rev. 1.2, 2007-05 27 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram 4 truth tables the truth tables in this chapter summar ize the commands and there signal coding to control a standard double-data-rate-two sdram. table 22 command truth table function cke cs ras cas we ba0 ba1 ba2 a[13:11] a10 a[9:0] note 1)2)3) 1) the state of odt does not affect the states described in this table. the odt function is not available during self refresh. 2) ?x? means ?h or l (but a defined logic level)?. 3) operation that is not specified is ill egal and after such an event, in order to guarantee proper operation, the dram must be powered down and then restarted through the specified initializa tion sequence before normal operation can continue. previous cycle current cycle (extended) mode register set h h l l l l ba op code 4)5) 4) all ddr2 sdram commands are defined by states of cs , we , ras , cas , and cke at the rising edge of the clock. 5) bank addresses ba[2:0] determine which bank is to be operated upon. for (e)mrs ba[2:0] selects an (extended) mode register. auto-refresh h h l l l h x x x x 4) self-refresh entry h l l l l h x x x x 4)6) 6) v ref must be maintained during self refresh operation. self-refresh exit l h h x x x x x x x 4)6)7) 7) self refresh exit is asynchronous. lh h h single bank precharge h h l l h l ba x l x 4)5) precharge all banks h h l l h l x x h x 4) bank activate h h l l h h ba row address 4)5) write h h l h l l ba column l column 4)5)8) 8) burst reads or writes at bl = 4 cannot be terminated. write with auto- precharge h h l h l l ba column h column 4)5)8) read h h l h l h ba column l column 4)5)8) read with auto- precharge h h l h l h ba column h column 4)5)8) no operation h x l h h h x x x x 4) device deselect h x h x x x x x x x 4) power down entry h l h x x x x x x x 4)9) 9) the power down mode does not perform any refresh operations. the duration of power down is therefore limited by the refresh requirements. lh h h power down exit l h h x x x x x x x 4)9) lh h h
internet data sheet rev. 1.2, 2007-05 28 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram table 23 clock enable (cke) truth table for synchronous transitions table 24 data mask (dm) truth table current state 1) 1) current state is the state of the ddr2 sdram immediately prior to clock edge n. cke command (n) 2) 3) ras , cas , we 2) command (n) is the command registered at clock e dge n, and action (n) is a result of command (n) 3) the state of odt does not affect the states described in this table. the odt function is not available during self refresh. action (n) 2) note 4)5) 4) cke must be maintained high while the device is in ocd calibration mode. 5) operation that is not specif ied is illegal and after such an event, in order to guarantee proper operation, the dram must be powered down and then restarted through the specified initializa tion sequence before normal operation can continue. previous cycle 6) (n-1) 6) cke (n) is the logic state of cke at clock edge n; c ke (n-1) was the state of cke at the previous clock edge. current cycle 6) (n) power-down l l x maintain power-down 7)8)11) 7) the power-down mode does not perform any refresh operations. the duration of power-down mode is therefor limited by the refre sh requirements 8) ?x? means ?don?t care (including floating around v ref )? in self refresh and power down. however odt must be driven high or low in power down if the odt function is enabled (bit a2 or a6 set to ?1? in emrs(1)). l h deselect or nop power-down exit 7)9)10)11) 9) all states and sequences not shown ar e illegal or reserved unless explicitly described else where in this document. 10) valid commands for power-down entry and exit are nop and deselect only. 11) t cke.min of 3 clocks means cke must be registered on three consecutive pos itive clock edges. cke must remain at the valid input level t he entire time it takes to achieve the 3 clocks of registration. th us, after any cke transition, cke may not transition from its v alid level during the time period of t is + 2 t ck + t ih . self refresh l l x maintain self refresh 8)11)12) 12) v ref must be maintained during self refresh operation. l h deselect or nop self refresh exit 9)11)12)13)14) 13) on self refresh exit deselect or nop commands must be issued on every clock edge occurring during the t xsnr period. read commands may be issued only after t xsrd (200 clocks) is satisfied. 14) valid commands for self refresh exit are nop and deselct only. bank(s) active h l deselect or nop active power-down entry 7)9)10)11)15) 15) power-down and self refresh can not be entered while read or write operations, (extended) mode register operations, precharg e or refresh operations are in progress. all banks idle h l deselect or nop precharge power-down entry 9)10)11)15) h l autorefresh self refresh entry 7)11)14)16) 16) self refresh mode can only be entered from the all banks idle state. any state other than listed above h h refer to the command truth table 17) 17) must be a legal command as defined in the command truth table. name (function) dm dqs note write enable l valid 1) 1) used to mask write data; provided coincident with the corresponding data. write inhibit h x 1)
internet data sheet rev. 1.2, 2007-05 29 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram 5 electrical characteristics this chapter describes the electrical characteristics. 5.1 absolute maximum ratings caution is needed not to exceed absolute maximum ratings of the dram device listed in table 25 at any time. table 25 absolute maximum ratings attention: stresses greater than those listed under ?abs olute maximum ratings? may cause permanent damage to the device. this is a stress rating only and functi onal operation of the device at these or any other conditions above those indicated in the operational sect ions of this specification is not implied. exposure to absolute maximum rating conditions fo r extended periods may affect reliability. table 26 dram component operating temperature range symbol parameter rating unit note min. max. v dd voltage on v dd pin relative to v ss ?1.0 +2.3 v 1) 1) when v dd and v ddq and v ddl are less than 500 mv; v ref may be equal to or less than 300 mv. v ddq voltage on v ddq pin relative to v ss ?0.5 +2.3 v 1)2) v ddl voltage on v ddl pin relative to v ss ?0.5 +2.3 v 1)2) v in , v out voltage on any pin relative to v ss ?0.5 +2.3 v 1) t stg storage temperature ?55 +100 c 1)2) 2) storage temperature is the case surface temperature on the center/top side of the dram. symbol parameter rating unit note min. max. t oper operating temperature 0 95 c 1)2)3)4) 1) operating temperature is the case surface te mperature on the center / top side of the dram. 2) the operating temperature range are the temperatures where all dram specification will be supported. during operation, the dr am case temperature must be maintained between 0 - 95 c under all other specification parameters. 3) above 85 c the auto-refresh command interval has to be reduced to t refi = 3.9 s 4) when operating this product in the 85 c to 95 c t case temperature range, the high temperature self refresh has to be enabled by setting emr(2) bit a7 to ?1?. when the high temperatur e self refresh is enabled there is an increase of i dd6 by approximately 50 %
internet data sheet rev. 1.2, 2007-05 30 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram 5.2 dc characteristics input and output 0s are higher with dual-die components com pared to standard single-die components, due to the double loading of the input / output pins, except cs[1:0], cke[1: 0] and odt[1:0] and the additi onal package internal wiring. table 27 recommended dc operating conditions (sstl_18) table 28 odt dc electrical characteristics table 29 input and output leakage currents symbol parameter rating unit note min. typ. max. v dd supply voltage 1.7 1.8 1.9 v 1) 1) v ddq tracks with v dd , v dddl tracks with v dd . ac parameters are measured with v dd , v ddq and v dddl tied together. v dddl supply voltage for dll 1.7 1.8 1.9 v 1) v ddq supply voltage for output 1.7 1.8 1.9 v 1) v ref input reference voltage 0.49 v ddq 0.5 v ddq 0.51 v ddq v 2)3) 2) the value of v ref may be selected by the user to provide optimum noi se margin in the system. typically the value of v ref is expected to be about 0.5 v ddq of the transmitting device and v ref is expected to track variations in v ddq . 3) peak to peak ac noise on v ref may not exceed 2 % v ref (dc) v tt termination voltage v ref ? 0.04 v ref v ref + 0.04 v 4) 4) v tt is not applied directly to the device. v tt is a system supply for signal terminati on resistors, is expected to be set equal to v ref , and must track variations in die dc level of v ref . parameter / condition sym bol min. nom. max. unit note termination resistor impedance value for emrs(1)[a6,a2] = [0,1]; 75 ohm rtt1(eff) 60 75 90 ? 1) 1) measurement definition for rtt(eff): apply v ih(ac) and v il(ac) to test pin separately, then measure current i ( v ihac ) and i ( v ilac ) respectively. rtt(eff) = ( v ih(ac) ? v il(ac) ) /( i ( v ihac ) ? i ( v ilac )). termination resistor impedance value for emrs(1)[a6,a2] =[1,0]; 150 ohm rtt2(eff) 120 150 180 ? 1) termination resistor impedance value for emrs(1)(a6,a2)=[1,1]; 50 ohm rtt3(eff) 40 50 60 ? 1) deviation of v m with respect to v ddq / 2 delta v m ?6.00 ? + 6.00 % 2) 2) measurement definition for v m : turn odt on and measure voltage ( v m ) at test pin (midpoint) with no load: delta v m =((2 x v m / v ddq )? 1) x 100 % symbol parameter / condition min. max. unit note i il input leakage current; any input 0 v < v in < v dd ?2 +2 a 1) 1) all other pins not under test = 0 v i ol output leakage current; 0 v < vout < v ddq ?5 +5 a 2) 2) dq?s, ldqs, ldqs , udqs, udqs , dqs, dqs , rdqs, rdqs are disabled and odt is turned off
internet data sheet rev. 1.2, 2007-05 31 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram 5.3 dc & ac characteristics ddr2 sdram pin timing are specified for either single ended or differential mode depending on the setting of the emrs(1) ?enable dqs ? mode bit; timing advantages of differential mode are realized in system des ign. the method by which the ddr2 sdram pin timing are measured is mode dependent. in single ended mode, timing relationships are measured relative to the rising or falling edges of dqs crossing at v ref . in differential mode, these ti ming relationships are measured relative to the crosspoint of dqs and its complement, dqs . this distinction in timing methods is verified by design and characterization but not subject to production test. in single ended mode, the dqs (and rdqs ) signals are internally disabled and don?t care. table 30 dc & ac logic input levels for ddr2-667 and ddr2-800 table 31 dc & ac logic input levels for ddr2-533 and ddr2-400 symbol parameter ddr2-667, ddr2-800 units min. max. v ih(dc) dc input logic high v ref + 0.125 v ddq + 0.3 v v il(dc) dc input low ?0.3 v ref ? 0.125 v v ih(ac) ac input logic high v ref + 0.200 ? v v il(ac) ac input low ? v ref ? 0.200 v symbol parameter ddr2-533, ddr2-400 units min. max. v ih(dc) dc input logic high v ref + 0.125 v ddq + 0.3 v v il(dc) dc input low ?0.3 v ref - 0.125 v v ih(ac) ac input logic high v ref + 0.250 ? v v il(ac) ac input low ? v ref - 0.250 v
internet data sheet rev. 1.2, 2007-05 32 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram table 32 single-ended ac input test conditions figure 4 single-ended ac input test conditions diagram symbol condition value unit note v ref input reference voltage 0.5 x v ddq v 1) 1) input waveform timing is referenced to the input signal crossing through the v ref level applied to the device under test. v swing.max input signal maximum peak to peak swing 1.0 v 1) slew input signal minimum slew rate 1.0 v / ns 2)3) 2) the input signal minimum slew rate is to be maintained over the range from v ih(ac).min to v ref for rising edges and the range from v ref to v il(ac).max for falling edges as shown in figure 4 3) ac timings are referenced with input waveforms switching from v il(ac) to v ih(ac) on the positive transitions and v ih(ac) to v il(ac) on the negative transitions. 03(7 'howd75 'howd7) 9 6:,1*0$; 9 ''4 9 ,+df plq 9 ,+gf plq 9 5() 9 ,/gf pd[ 9 ,/df pd[ 9 66 5lvlqj6ohz 9 ,+df plq9 5() 'howd75 9 5() 9 ,/df pd[ )doolqj6ohz 'howd7)
internet data sheet rev. 1.2, 2007-05 33 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram table 33 differential dc and ac in put and output logic levels figure 5 differential dc and ac input and output logic levels diagram symbol parameter min. max. unit note v in(dc) dc input signal voltage ?0.3 v ddq + 0.3 ? 1) 1) v in(dc) specifies the allowable dc execution of eac h input of differential pair such as ck, ck , dqs, dqs etc. v id(dc) dc differential input voltage 0.25 v ddq + 0.6 ? 2) 2) v id(dc) specifies the input differential voltage v tr ? v cp required for switching. the minimum value is equal to v ih(dc) ? v il(dc) . v id(ac) ac differential input voltage 0.5 v ddq + 0.6 v 3) 3) v id(ac) specifies the input differential voltage v tr ? v cp required for switching. the minimum value is equal to v ih(ac) ? v il(ac) . v ix(ac) ac differential cross point input voltage 0.5 v ddq ? 0.175 0.5 v ddq + 0.175 v 4) 4) the value of v ix(ac) is expected to equal 0.5 v ddq of the transmitting device and v ix(ac) is expected to track variations in v ddq . v ix(ac) indicates the voltage at which differential input signals must cross. v ox(ac) ac differential cross po int output voltage 0.5 v ddq ? 0.125 0.5 v ddq + 0.125 v 5) 5) the value of v ox(ac) is expected to equal 0.5 v ddq of the transmitting device and v ox(ac) is expected to track variations in v ddq . v ox(ac) indicates the voltage at which differential input signals must cross. & u r v v l q j 3 r l q w 9 ' ' 4 9 6 6 4 9 , ' 9 , ; r u 9 2 ; 9 7 5 9 & 3
internet data sheet rev. 1.2, 2007-05 34 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram 5.4 output buffer characteristics this chapter describes the output buffer characteristics. table 34 sstl_18 output dc current drive table 35 sstl_18 output ac test conditions table 36 ocd default characteristics symbol parameter sstl_18 unit note i oh output minimum source dc current ?13.4 ma 1)2) 1) v ddq = 1.7 v; v out = 1.42 v. ( v out ? v ddq ) / i oh must be less than 21 ohm for values of v out between v ddq and v ddq ? 280 mv. 2) the values of i oh(dc) and i ol(dc) are based on the conditions given in 1) and 3) . they are used to test drive current capability to ensure v ih.min . plus a noise margin and v il.max minus a noise margin are delivered to an sstl_18 rece iver. the actual current values are derived by shifting the desired driver operating points along 21 ohm lo ad line to define a convenient current for measurement. i ol output minimum sink dc current 13.4 ma 2)3) 3) v ddq = 1.7 v; v out = 280 mv. v out / i ol must be less than 21 ohm for values of v out between 0 v and 280 mv. symbol parameter sstl_18 unit note v oh minimum required output pull-up v tt + 0.603 v 1) 1) sstl_18 test load for v oh and v ol is different from the referenced load. the sstl_18 te st load has a 20 ohm series resistor additionally to the 25 ohm termination resistor into v tt . the sstl_18 definition assumes that 335 mv must be developed across the effectively 25 ohm termination resistor (13.4 ma 25 ohm = 335 mv). with an additional series resist or of 20 ohm this translates into a minimum requirement of 603 mv swing relative to v tt , at the ouput device (13.4 ma 45 ohm = 603 mv). v ol maximum required output pull-down v tt ? 0.603 v 1) v otr output timing measurement reference level 0.5 v ddq v symbol description min. nominal max. unit note ? output impedance ? ? 1)2) 1) v ddq = 1.8 v 0.1 v; v dd = 1.8 v 0.1 v 2) impedance measurement condition for output source dc current: v ddq = 1.7 v, v out = 1420 mv; ( v out ? v ddq ) / i oh must be less than 23.4 ohms for values of v out between v ddq and v ddq ? 280 mv. impedance measurement condi tion for output sink dc current: v ddq = 1.7 v; v out = ?280 mv; v out / i ol must be less than 23.4 ohms for values of v out between 0 v and 280 mv. ? pull-up / pull down mismatch 0 ? 4 ? 1)2)3) 3) mismatch is absolute value between pull-up and pull- down, both measured at same temperature and voltage. ? output impedance step size for ocd calibration 0?1.5 ? 4) 4) this represents the step size when the ocd is near 18 ohms at nominal conditions ac ross all process parameters and represents only the dram uncertainty. a 0 ohm value (no calibration) can only be achieved if the ocd impedance is 18 0.75 ohms under nominal conditions. s out output slew rate 1.5 ? 5.0 v / ns 1)5)6)7) 5) the absolute value of the slew rate as measured from dc to dc is equal to or greater than the slew rate as measured from ac t o ac. this is verified by design and characterization but not subject to production test. 6) timing skew due to dram output slew rate mis-match between dqs / dqs and associated dq?s is included in t dqsq and t qhs specification. 7) dram output slew rate specification app lies to 400, 533 and 667 mt/s speed bins.
internet data sheet rev. 1.2, 2007-05 35 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram 5.5 input / output capacitance this chapter contains the input / output capacitance. table 37 input / output capa citance for ddr2-800 table 38 input / output capa citance for ddr2-667 symbol parameter ddr2-800 min. max. unit cck input capacitance, ck and ck 1.0 2.0 pf cdck input capacitance delta, ck and ck ?0.25pf ci input capacitance, all ot her input-only pins 1.0 1.75 pf cdi input capacitance delta, all other input-only pins ? 0.25 pf cio input/output capacitance, dq, dm, dqs, dqs , rdqs, rdqs 2.5 3.5 pf cdio input/output c apacitance delta, dq, dm, dqs, dqs , rdqs, rdqs ?0.5pf symbol parameter ddr2-667 min. max. unit cck input capacitance, ck and ck 1.0 2.0 pf cdck input capacitance delta, ck and ck ?0.25pf ci input capacitance, all ot her input-only pins 1.0 2.0 pf cdi input capacitance delta, all other input-only pins ? 0.25 pf cio input/output capacitance, dq, dm, dqs, dqs , rdqs, rdqs 2.5 3.5 pf cdio input/output c apacitance delta, dq, dm, dqs, dqs , rdqs, rdqs ?0.5pf
internet data sheet rev. 1.2, 2007-05 36 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram table 39 input / output capa citance for ddr2-533 table 40 input / output capa citance for ddr2-400 symbol parameter ddr2-533 min. max. unit cck input capacitance, ck and ck 1.0 2.0 pf cdck input capacitance delta, ck and ck ?0.25pf ci input capacitance, all ot her input-only pins 1.0 2.0 pf cdi input capacitance delta, all other input-only pins ? 0.25 pf cio input/output capacitance, dq, dm, dqs, dqs , rdqs, rdqs 2.5 4.0 pf cdio input/output c apacitance delta, dq, dm, dqs, dqs , rdqs, rdqs ?0.5pf symbol parameter ddr2-400 min. max. unit cck input capacitance, ck and ck 1.0 2.0 pf cdck input capacitance delta, ck and ck ?0.25pf ci input capacitance, all ot her input-only pins 1.0 2.0 pf cdi input capacitance delta, all other input-only pins ? 0.25 pf cio input/output capacitance, dq, dm, dqs, dqs , rdqs, rdqs 2.5 4.0 pf cdio input/output c apacitance delta, dq, dm, dqs, dqs , rdqs, rdqs ?0.5pf
internet data sheet rev. 1.2, 2007-05 37 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram 5.6 overshoot and undershoot specification this chapter contains overshoot and undershoot specification. table 41 ac overshoot / undershoot specification for address and control pins figure 6 ac overshoot / undershoot diagram for address and control pins parameter ddr2-400 ddr2-533 ddr2-667 ddr2-800 unit maximum peak amplitude allowed for overshoot area 0.9 0.9 0.9 0.9 v maximum peak amplitude allowed for undershoot area 0.9 0.9 0.9 0.9 v maximum overshoot area above v dd 1.33 1.00 0.80 0.66 v.ns maximum undershoot area below v ss 1.33 1.00 0.80 0.66 v.ns 03(7 9rowv9 9 '' 9 66 0d[lpxp$psolwxgh 7lphqv 0d[lpxp$psolwxgh 2yhuvkrrw$uhd 8qghuvkrrw$uhd
internet data sheet rev. 1.2, 2007-05 38 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram table 42 ac overshoot / undershoot spec. for clock, data, strobe and mask pins figure 7 ac overshoot / undershoot diagram for clock, data, strobe and mask pins parameter ddr2-400 ddr2-533 ddr2-667 ddr2-800 unit maximum peak amplitude allowed for overshoot area 0.9 0.9 0.9 0.9 v maximum peak amplitude allowed for undershoot area 0.9 0.9 0.9 0.9 v maximum overshoot area above v ddq 0.38 0.28 0.23 0.23 v.ns maximum undershoot area below v ssq 0.38 0.28 0.23 0.23 v.ns 03(7 9rowv9 9 ''4 9 664 0d[lpxp$psolwxgh 7lphqv 0d[lpxp$psolwxgh 2yhuvkrrw$uhd 8qghuvkrrw$uhd
internet data sheet rev. 1.2, 2007-05 39 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram 6 currents measurement conditions this chapter describes the current meas urement specifications and conditions. table 43 i dd measurement conditions parameter symbol note operating current - one bank active - precharge t ck = t ck(idd) , t rc = t rc(idd) , t ras = t ras.min(idd) , cke is high, cs is high between valid commands. address and control inputs are switching; databus inputs are switching. i dd0 1)2)3)4)5) 6) operating current - one bank active - read - precharge i out = 0 ma, bl = 4, t ck = t ck(idd) , t rc = t rc(idd) , t ras = t ras.min(idd) , t rcd = t rcd(idd) , al = 0, cl = cl(idd); cke is high, cs is high between valid commands. address and control inputs are switching; databus inputs are switching. i dd1 1)2)3)4)5) 6) precharge power-down current all banks idle; cke is low; t ck = t ck(idd) ;other control and address inputs are stable; data bus inputs are floating . i dd2p 1)2)3)4)5) 6) precharge standby current all banks idle; cs is high; cke is high; t ck = t ck(idd) ; other control and address inputs are switching, data bus inputs are switching . i dd2n 1)2)3)4)5) 6) precharge quiet standby current all banks idle; cs is high; cke is high; t ck = t ck(idd) ; other control and address inputs are stable, data bus inputs are floating. i dd2q 1)2)3)4)5) 6) active power-down current all banks open; t ck = t ck(idd) , cke is low; other control and address inputs are stable; data bus inputs are floating. mrs a12 bit is set to ?0? (fast power-down exit). i dd3p(0) 1)2)3)4)5) 6) active power-down current all banks open; t ck = t ck(idd) , cke is low; other cont rol and address inputs are stable, data bus inputs are floating. mrs a12 bit is set to 1 (slow power-down exit); i dd3p(1) 1)2)3)4)5) 6) active standby current all banks open; t ck = t ck(idd) ; t ras = t ras.max(idd) , t rp = t rp(idd) ; cke is high, cs is high between valid commands. address inputs are switching; data bus inputs are switching; i dd3n 1)2)3)4)5) 6) operating current burst read: all banks open; continuous burst reads; bl = 4; al = 0, cl = cl (idd) ; t ck = t ck(idd) ; t ras = t ras.max.(idd) , t rp = t rp(idd) ; cke is high, cs is high between valid commands. address inputs are switching; data bus inputs are switching; i out = 0 ma. i dd4r 1)2)3)4)5) 6) operating current burst write: all banks open; continuous burst writes; bl = 4; al = 0, cl = cl (idd) ; t ck = t ck(idd) ; t ras = t ras.max(idd) , t rp = t rp(idd) ; cke is high, cs is high between valid commands. address inputs are switching; data bus inputs are switching; i dd4w 1)2)3)4)5) 6) burst refresh current t ck = t ck(idd) , refresh command every t rfc = t rfc(idd) interval, cke is high, cs is high between valid commands, other control and address inputs ar e switching, data bus inputs are switching. i dd5b 1)2)3)4)5) 6) distributed refresh current t ck = t ck(idd) , refresh command every t refi = 7.8 s interval, cke is low and cs is high between valid commands, other control and address inputs ar e switching, data bus inputs are switching. i dd5d 1)2)3)4)5) 6)
internet data sheet rev. 1.2, 2007-05 40 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram table 44 definition for i dd self-refresh current cke 0.2 v; external clock off, ck and ck at 0 v; other control and addre ss inputs are floating, data bus inputs are floating. i dd6 1)2)3)4)5) 6) operating bank interleave read current 1. all banks interleaving reads, i out = 0 ma; bl = 4, cl = cl (idd) , al = t rcd(idd) -1 t ck(idd) ; t ck = t ck(idd) , t rc = t rc(idd) , t rrd = t rrd(idd) ; tfaw = tfaw(idd); cke is high, cs is high between valid commands. address bus inputs are stable during deselects; data bus is switching. 2. timing pattern: i dd7 1)2)3)4)5) 6)7) ddr2-400-333: a0 ra0 a1 ra1 a2 ra2 a3 ra3 d d d (11 clocks) ddr2-533-333: a0 ra0 d a1 ra1 d a2 ra2 d a3 ra3 d d d d (15 clocks) ddr2-667-444: a0 ra0 d d a1 ra1 d d a2 ra2 d d a3 ra3 d d d d d (19 clocks) ddr2-667-555: a0 ra0 d d a1 ra1 d d a2 ra2 d d a3 ra3 d d d d d d (20 clocks) ddr2-800-555: a0 ra0 d d d a1 ra1 d d d a2 ra2 d d d a3 ra3 d d d d d(22 clocks) ddr2-800-666: a0 ra0 d d d a1 ra1 d d d a2 ra2 d d d a3 ra3 d d d d d d(23 clocks) 1) v ddq = 1.8 v 0.1 v; v dd = 1.8 v 0.1 v 2) i dd specifications are tested after the device is properly initialized. 3) i dd parameter are specified with odt disabled. 4) data bus consists of dq, dm, dqs, dqs , rdqs, rdqs , ldqs, ldqs , udqs and udqs . 5) definitions for i dd : see table 44 6) timing parameter minimum and maximum values for i dd current measurements are defined in chapter 7 . 7) a = activate, ra = read with auto-precharge, d=deselect parameter description low defined as v in v il(ac).max high defined as v in v ih(ac).min stable defined as inputs are stable at a high or low level floating defined as inputs are v ref = v ddq / 2 switching defined as: inputs ar e changing between high and low every other clock (once per two clocks) for address and control signals, and inputs changing between high and low every other clock (once per clock) for dq signals not including mask or strobes parameter symbol note
internet data sheet rev. 1.2, 2007-05 41 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram table 45 i dd specification symbol 25f 2.5 3 3s 3.7 5 unit note ddr2 - 800 ddr2 - 800 ddr2 - 667 ddr2 - 667 ddr2 - 533 ddr2 - 400 max. max. max. max. max. max. i dd0 125 125 110 110 100 95 ma 4/ 8 150 150 135 135 125 120 ma 16 i dd1 135 135 120 120 105 100 ma 4/ 8 160 160 145 145 130 125 ma 16 i dd2p 12 12 12 12 12 12 ma i dd2n 70 70 65 65 55 50 ma i dd2q 65 65 60 60 50 45 ma i dd3p_0 (fast) 48 48 45 45 38 35 ma i dd3p_1 (slow) 15 15 15 15 15 15 ma i dd3n 90 90 70 70 60 55 ma i dd4r 200 200 170 170 150 135 ma 4/ 8 240 240 205 205 175 150 ma 16 i dd4w 200 200 170 170 150 135 ma 4/ 8 240 240 205 205 175 150 ma 16 i dd5b 225 225 210 210 200 190 ma i dd5d 13 13 13 13 13 13 ma 1) 1) 0 t case 85 c. i dd6 10 10 10 10 10 10 ma 1) standard ? ? ? 3.7 3.7 3.7 ma 1) 4/ 8 low power ? ? ? tbd tbd tbd ma 1) 16 low power i dd7 270 270 230 230 225 215 ma 4/ 8 340 340 300 300 280 265 ma 16
internet data sheet rev. 1.2, 2007-05 42 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram 7 timing characteristics this chapter contains speed grade definition, ac timing parameter and odt tables. 7.1 speed grade definitions all speed grades faster than ddr2-400b comp ly with ddr2-400b timing specifications ( t ck = 5ns with t ras = 40ns). table 46 speed grade definition speed bins for ddr2?800 speed grade ddr2?800d ddr2?800e unit note qag sort name ?2.5f ?2.5 cas-rcd-rp latencies 5?5?5 6?6?6 t ck parameter symbol min. max. min. max. ? clock frequency @ cl = 3 t ck 58 58 ns 1)2)3)4) 1) timings are guaranteed with ck/ck differential slew rate of 2.0 v/ns. for dqs si gnals timings are guaranteed with a differential slew rate of 2.0 v/ns in differential strobe mode and a slew rate of 1 v/ns in single ended mode. timings are further guaranteed for normal ocd drive strength (emrs(1) a1 = 0) under the ?reference load for timing measurements?. 2) the ck/ck input reference level (for timing reference to ck/ck ) is the point at which ck and ck cross. the dqs / dqs , rdqs / rdqs , input reference level is the crosspoint when in differential st robe mode; the input reference level for signals other than ck/c k, dqs / dqs, rdqs / rdqs is defined . 3) inputs are not recognized as valid until v ref stabilizes. during the period before v ref stabilizes, cke = 0.2 x v ddq is recognized as low. 4) the output timing reference voltage level is v tt . @ cl = 4 t ck 3.75 8 3.75 8 ns 1)2)3)4) @ cl = 5 t ck 2.5 8 3 8 ns 1)2)3)4) @ cl = 6 t ck 2.5 8 2.5 8 ns 1)2)3)4) row active time t ras 45 70000 45 70000 ns 1)2)3)4)5) 5) t ras.max is calculated from the maximum amount of time a ddr2 dev ice can operate without a refresh command which is equal to 9 x t refi . row cycle time t rc 57.5 ? 60 ? ns 1)2)3)4) ras-cas-delay t rcd 12.5 ? 15 ? ns 1)2)3)4) row precharge time t rp 12.5 ? 15 ? ns 1)2)3)4)
internet data sheet rev. 1.2, 2007-05 43 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram table 47 speed grade definition speed bins for ddr2?667 table 48 speed grade definition speed bins for ddr2?533c speed grade ddr2?667c ddr2?667d unit note qag sort name ?3 ?3s cas-rcd-rp latencies 4?4?4 5?5?5 t ck parameter symbol min. max. min. max. ? clock frequency @ cl = 3 t ck 5858ns 1)2)3)4) 1) timings are guaranteed with ck/ck differential slew rate of 2.0 v/ns. for dqs si gnals timings are guaranteed with a differential slew rate of 2.0 v/ns in differential strobe mode and a slew rate of 1 v/ns in single ended mode. timings are further guaranteed for normal ocd drive strength (emrs(1) a1 = 0) under the ?reference load for timing measurements?. 2) the ck/ck input reference level (for timing reference to ck/ck ) is the point at which ck and ck cross. the dqs / dqs , rdqs / rdqs , input reference level is the crosspoint when in differential st robe mode; the input reference level for signals other than ck/c k, dqs / dqs, rdqs / rdqs is defined. 3) inputs are not recognized as valid until v ref stabilizes. during the period before v ref stabilizes, cke = 0.2 x v ddq is recognized as low. 4) the output timing reference voltage level is v tt . @ cl = 4 t ck 383.758ns 1)2)3)4) @ cl = 5 t ck 3838ns 1)2)3)4) row active time t ras 45 70000 45 70000 ns 1)2)3)4)5) 5) t ras.max is calculated from the maximum amount of time a ddr2 dev ice can operate without a refresh command which is equal to 9 x t refi . row cycle time t rc 57 ? 60 ? ns 1)2)3)4) ras-cas-delay t rcd 12 ? 15 ? ns 1)2)3)4) row precharge time t rp 12 ? 15 ? ns 1)2)3)4) speed grade ddr2?533c unit note qag sort name ?3.7 cas-rcd-rp latencies 4?4?4 t ck parameter symbol min. max. ? clock frequency @ cl = 3 t ck 58 ns 1)2)3)4) 1) timings are guaranteed with ck/ck differential slew rate of 2.0 v/ns. for dqs si gnals timings are guaranteed with a differential slew rate of 2.0 v/ns in differential strobe mode and a slew rate of 1 v/ns in single ended mode. timings are further guaranteed for normal ocd drive strength (emrs(1) a1 = 0) under the ?reference load for timing measurements?. 2) the ck/ck input reference level (for timing reference to ck/ck ) is the point at which ck and ck cross. the dqs / dqs , rdqs / rdqs , input reference level is the crosspoint when in differential strobe mode; the input reference level for signals other than ck/c k, dqs / dqs, rdqs / rdqs is defined. @ cl = 4 t ck 3.75 8 ns 1)2)3)4) @ cl = 5 t ck 3.75 8 ns 1)2)3)4) row active time t ras 45 70000 ns 1)2)3)4)5) row cycle time t rc 60 ? ns 1)2)3)4) ras-cas-delay t rcd 15 ? ns 1)2)3)4) row precharge time t rp 15 ? ns 1)2)3)4)
internet data sheet rev. 1.2, 2007-05 44 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram table 49 speed grade defi nition speed bi ns for ddr2-400b 3) inputs are not recognized as valid until v ref stabilizes. during the period before v ref stabilizes, cke = 0.2 x v ddq is recognized as low. 4) the output timing reference voltage level is v tt . 5) t ras.max is calculated from the maximum amount of time a ddr2 devic e can operate without a refresh command which is equal to 9 x t refi . speed grade ddr2?400b unit note qag sort name ?5 cas-rcd-rp latencies 3?3?3 t ck parameter symbol min. max. ? clock frequency @ cl = 3 t ck 58 ns 1)2)3)4) 1) timings are guaranteed with ck/ck differential slew rate of 2.0 v/ns. for dqs si gnals timings are guaranteed with a differential slew rate of 2.0 v/ns in differential strobe mode and a slew rate of 1 v/ns in single ended mode. timings are further guaranteed for normal ocd drive strength (emrs(1) a1 = 0) under the ?reference load for timing measurements?. 2) the ck/ck input reference level (for timing reference to ck/ck ) is the point at which ck and ck cross. the dqs / dqs , rdqs / rdqs , input reference level is the crosspoint when in differential strobe mode; the input reference level for signals other than ck/c k, dqs / dqs, rdqs / rdqs is defined. 3) inputs are not recognized as valid until v ref stabilizes. during the period before v ref stabilizes, cke = 0.2 x v ddq is recognized as low. 4) the output timing reference voltage level is v tt . @ cl = 4 t ck 58 ns 1)2)3)4) @ cl = 5 t ck 58 ns 1)2)3)4) row active time t ras 40 70000 ns 1)2)3)4)5) 5) t ras.max is calculated from the maximum amount of time a ddr2 device can operate without a refresh command which is equal to 9 x t refi . row cycle time t rc 55 ? ns 1)2)3)4) ras-cas-delay t rcd 15 ? ns 1)2)3)4) row precharge time t rp 15 ? ns 1)2)3)4)
internet data sheet rev. 1.2, 2007-05 45 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram 7.2 component ac timing parameters list of timing parameters tables. table 50 dram component timing parameter by speed grade - ddr2?800 parameter symbol ddr2?800 unit note 1)2)3)4)5)6)7) min. max. dq output access time from ck / ck t ac ?400 +400 ps 8) cas to cas command delay t ccd 2?nck average clock high pulse width t ch.avg 0.48 0.52 t ck.avg 9)10) average clock period t ck.avg 2500 8000 ps 9)10) cke minimum pulse width ( high and low pulse width) t cke 3?nck 11) average clock low pulse width t cl.avg 0.48 0.52 t ck.avg 9)10) auto-precharge write recovery + precharge time t dal wr + t nrp ?nck 12)13) minimum time clocks remain on after cke asynchronously drops low t delay t is + t ck .avg + t ih ?? ns dq and dm input hold time t dh.base 125 ?? ps 18)19)14) dq and dm input pulse width for each input t dipw 0.35 ? t ck.avg dqs output access time from ck / ck t dqsck ?350 +350 ps 8) dqs input high pulse width t dqsh 0.35 ? t ck.avg dqs input low pulse width t dqsl 0.35 ? t ck.avg dqs-dq skew for dqs & associated dq signals t dqsq ? 200 ps 15) dqs latching rising transition to associated clock edges t dqss ? 0.25 + 0.25 t ck.avg 16) dq and dm input setup time t ds.base 50 ?? ps 17)18)19) dqs falling edge hold time from ck t dsh 0.2 ? t ck.avg 16) dqs falling edge to ck setup time t dss 0.2 ? t ck.avg 16) four activate window for 1kb page size products t faw 35 ? ns 34) four activate window for 2kb page size products t faw 45 ? ns 34) ck half pulse width t hp min( t ch.abs , t cl.abs ) __ ps 20) data-out high-impedance time from ck / ck t hz ? t ac.max ps 8)21) address and control input hold time t ih.base 250 ? ps 22)24) control & address input pulse width for each input t ipw 0.6 ? t ck.avg address and control input setup time t is.base 175 ? ps 23)24) dq low impedance time from ck/ck t lz.dq 2x t ac.min t ac.max ps 8)21) dqs/dqs low-impedance time from ck / ck t lz.dqs t ac.min t ac.max ps 8)21) mrs command to odt update delay t mod 012ns 34) mode register set command cycle time t mrd 2?nck ocd drive mode output delay t oit 012ns 34) dq/dqs output hold time from dqs t qh t hp ? t qhs ?ps 25)
internet data sheet rev. 1.2, 2007-05 46 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram dq hold skew factor t qhs ? 300 ps 26) average periodic refresh interval t refi ?7.8 s 27)28) ?3.9 s 28)29) auto-refresh to active/auto-refresh command period t rfc 127.5 ? ns 30) precharge-all (8 banks) command period t rp t rp +1 t ck ?ns read preamble t rpre 0.9 1.1 t ck.avg 31)32) read postamble t rpst 0.4 0.6 t ck.avg 31)33) active to active command period for 1kb page size products t rrd 7.5 ? ns 34) active to active command period for 2kb page size products t rrd 10 ? ns 34) internal read to precharge command delay t rtp 7.5 ? ns 34) write preamble t wpre 0.35 ? t ck.avg write postamble t wpst 0.4 0.6 t ck.avg write recovery time t wr 15 ? ns 34) internal write to read command delay t wtr 7.5 ? ns 34)35) exit power down to read command t xard 2?nck exit active power-down mode to read command (slow exit, lower power) t xards 8 ? al ? nck exit precharge power-down to any valid command (other than nop or deselect) t xp 2?nck exit self-refresh to a non-read command t xsnr t rfc +10 ? ns 34) exit self-refresh to read command t xsrd 200 ? nck write command to dqs associated clock edges wl rl ? 1 nck 1) v ddq = 1.8 v 0.1v; v dd = 1.8 v 0.1 v. 2) timing that is not specified is ille gal and after such an event, in order to guarantee proper operation, the dram must be pow ered down and then restarted through the specified initializa tion sequence before normal operation can continue. 3) timings are guaranteed with ck/ck differential slew rate of 2.0 v/ns. for dqs si gnals timings are guaranteed with a differential slew rate of 2.0 v/ns in differential strobe mode and a slew rate of 1 v/ns in single ended mode. . 4) the ck / ck input reference level (for timing reference to ck / ck ) is the point at which ck and ck cross. the dqs / dqs , rdqs / rdqs , input reference level is the crosspoint when in differential st robe mode. the input reference level for signals other than ck/c k , dqs/dqs , rdqs / rdqs is defined. 5) inputs are not recognized as valid until v ref stabilizes. during the period before v ref stabilizes, cke = 0.2 x v ddq is recognized as low. 6) the output timing reference voltage level is v tt . 7) new units, ? t ck.avg ? and ?nck?, are introduced in ddr2?667 and ddr2?800. unit ? t ck.avg ? represents the actual t ck.avg of the input clock under operation. unit ?nck? represents one clock cycle of the i nput clock, counting the actual clock edges. note that in ddr2?4 00 and ddr2?533, ? t ck ? is used for both concepts. example: t xp = 2 [nck] means; if power down exit is registered at tm, an active command may be registered at tm + 2, even if (tm + 2 - tm) is 2 x t ck.avg + t err.2per(min) . 8) when the device is operated with input clock jitter, this parameter needs to be derated by the actual t err(6-10per) of the input clock. (output deratings are relative to the sdram input clock.) for example, if the measured jitter into a ddr2?667 sdram has t err(6-10per).min = ? 272 ps and t err(6- 10per).max = + 293 ps, then t dqsck.min(derated) = t dqsck.min ? t err(6-10per).max = ? 400 ps ? 293 ps = ? 693 ps and t dqsck.max(derated) = t dqsck.max ? t err(6-10per).min = 400 ps + 272 ps = + 672 ps. similarly, t lz.dq for ddr2?667 derates to t lz.dq.min(derated) = - 900 ps ? 293 ps = ? 1193 ps and t lz.dq.max(derated) = 450 ps + 272 ps = + 722 ps. (caution on the min/max usage!) 9) input clock jitter spec parameter. these parameters and the ones in chapter 7.3 are referred to as 'input clock jitter spec parameters' and these parameters apply to ddr2?667 and ddr2?800 only. the jitter spec ified is a random jitter m eeting a gaussian distribution. parameter symbol ddr2?800 unit note 1)2)3)4)5)6)7) min. max.
internet data sheet rev. 1.2, 2007-05 47 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram 10) these parameters are specified per thei r average values, however it is underst ood that the relationship as defined in chapter 7.3 between the average timing and the absolute instantaneous timing holds all th e times (min. and max of spec values are to be used for ca lculations of chapter 7.3 ). 11) t cke.min of 3 clocks means cke must be registered on three consecutive positive clock edges. cke must remain at the valid input level t he entire time it takes to achieve the 3 clo cks of registration. thus, after any cke tr ansition, cke may not transition from its v alid level during the time period of t is + 2 x t ck + t ih . 12) dal = wr + ru{ t rp (ns) / t ck (ns)}, where ru stands for round up. wr refers to the twr parameter stored in the mrs. for t rp , if the result of the division is not already an integer, round up to the next highest integer. t ck refers to the application clock period. example: for ddr2?533 at t ck = 3.75 ns with t wr programmed to 4 clocks. t dal = 4 + (15 ns / 3.75 ns) clocks = 4 + (4) clocks = 8 clocks. 13) t dal.nck = wr [nck] + t nrp.nck = wr + ru{ t rp [ps] / t ck.avg [ps] }, where wr is the value programmed in the emr. 14) input waveform timing t dh with differential data strobe enabled mr[bit10] = 0, is refe renced from the differential data strobe crosspoint to the input signal crossing at the v ih.dc level for a falling signal and from the differential data strobe crosspoint to the input signal crossing at the v il.dc level for a rising signal applied to the device under test. dqs, dqs signals must be monotonic between v il.dc.max and v ih.dc.min . see figure 9 . 15) t dqsq : consists of data pin skew and output pattern effects, and p-c hannel to n-channel variation of the output drivers as well as o utput slew rate mismatch between dqs / dqs and associated dq in any given cycle. 16) these parameters are measured from a data strobe signal ((l/u/r)dqs / dqs ) crossing to its respec tive clock signal (ck / ck ) crossing. the spec values are not affected by t he amount of clock jitter applied (i.e. t jit.per , t jit.cc , etc.), as these are relative to the clock signal crossing. that is, these param eters should be met whether clock jitter is present or not. 17) input waveform timing t ds with differential data strobe enabled mr[bit10] = 0, is referenced from the input signal crossing at the v ih.ac level to the differential data strobe crosspoint for a ri sing signal, and from the input signal crossing at the v il.ac level to the differential data strobe crosspoint for a falling signal applied to the device under test. dqs, dqs signals must be monotonic between v il(dc)max and v ih(dc)min . see figure 9 . 18) if t ds or t dh is violated, data corruption may occur and the data must be re -written with valid data before a valid read can be executed. 19) these parameters are measured from a data signal ((l/u)dm, (l/u)dq0, (l/u)dq1, etc.) transition edge to its respective data strobe signal ((l/u/r)dqs / dqs ) crossing. 20) t hp is the minimum of the absolute half period of the actual input clock. t hp is an input parameter but not an input specification parameter. it is used in conjunction with t qhs to derive the dram output timing t qh . the value to be used for t qh calculation is determined by the following equation; t hp = min ( t ch.abs , t cl.abs ), where, t ch.abs is the minimum of the actual instantaneous clock high time; t cl.abs is the minimum of the actual in stantaneous clock low time. 21) t hz and t lz transitions occur in the same access time as valid data trans itions. these parameters are refe renced to a specific voltage lev el which specifies when the device output is no longer driving ( t hz ), or begins driving ( t lz ) . 22) input waveform timing is referenced from the input signal crossing at the v il.dc level for a rising signal and v ih.dc for a falling signal applied to the device under test. see figure 10 . 23) input waveform timing is referenced from the input signal crossing at the v ih.ac level for a rising signal and v il.ac for a falling signal applied to the device under test. see figure 10 . 24) these parameters are measured from a command/address signal (c ke, cs, ras, cas, we, odt, ba0, a0, a1, etc.) transition edge to its respective clock signal (ck / ck ) crossing. the spec values are not affect ed by the amount of cl ock jitter applied (i.e. t jit.per , t jit.cc , etc.), as the setup and hold are relative to the clock signal cr ossing that latches the command/address. that is, these paramet ers should be met whether clock jitter is present or not. 25) t qh = t hp ? t qhs , where: t hp is the minimum of the absolute half period of the actual input clock; and t qhs is the specification value under the max column. {the less half-pulse width distortion present, the larger the t qh value is; and the larger the valid data eye will be.} examples: 1) if the system provides t hp of 1315 ps into a ddr2?667 sdram, the dram provides t qh of 975 ps minimum. 2) if the system provides t hp of 1420 ps into a ddr2?667 sdram, the dram provides t qh of 1080 ps minimum. 26) t qhs accounts for: 1) the pulse duration distortion of on-chip clock circuits, which represents how well the actual t hp at the input is tra nsferred to the output; and 2) the worst case push-out of dqs on one transition followed by th e worst case pull-in of dq on the next transition, both of wh ich are independent of each other, due to data pin skew, output pattern effects, and pchannel to n-channel variation of the output driv ers. 27) the auto-refresh command interval has be reduced to 3.9 s when operating the ddr2 dram in a temperature range between 85 c and 95 c. 28) 0 c t case 85 c 29) 85 c < t case 95 c 30) a maximum of eight auto-refresh commands can be posted to any given ddr2 sdram device. 31) t rpst end point and t rpre begin point are not referenced to a specific voltage level but specify when the device output is no longer driving ( t rpst ), or begins driving ( t rpre ). figure 8 shows a method to calculate these points when the device is no longer driving ( t rpst ), or begins driving ( t rpre ) by measuring the signal at two different voltages. the actual voltage measurement poi nts are not critical as long as the calculation is consistent.
internet data sheet rev. 1.2, 2007-05 48 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram table 51 dram component timing parameter by speed grade - ddr2?667 32) when the device is operated with i nput clock jitter, this parameter needs to be derated by the actual t jit.per of the input clock. (output deratings are relative to the sdram input clock.) for example, if the measured jitter into a ddr2?667 sdram has t jit.per.min = ? 72 ps and t jit.per.max = + 93 ps, then t rpre.min(derated) = t rpre.min + t jit.per.min = 0.9 x t ck.avg ? 72 ps = + 2178 ps and t rpre.max(derated) = t rpre.max + t jit.per.max = 1.1 x t ck.avg + 93 ps = + 2843 ps. (caution on the min/max usage!). 33) when the device is operated with i nput clock jitter, this parameter needs to be derated by the actual t jit.duty of the input clock. (output deratings are relative to the sdram input clock.) for ex ample, if the measured jitter into a ddr2?667 sdram has t jit.duty.min = ? 72 ps and t jit.duty.max = + 93 ps, then t rpst.min(derated) = t rpst.min + t jit.duty.min = 0.4 x t ck.avg ? 72 ps = + 928 ps and t rpst.max(derated) = t rpst.max + t jit.duty.max = 0.6 x t ck.avg + 93 ps = + 1592 ps. (caution on the min/max usage!). 34) for these parameters, the ddr2 sdram device is characterized and verified to support t nparam = ru{ t param / t ck.avg }, which is in clock cycles, assuming all input cl ock jitter specifications are satisfied. for example, the device will support t nrp = ru{ t rp / t ck.avg }, which is in clock cycles, if all input clock jitter specifications are me t. this means: for ddr2?667 5?5?5, of which t rp = 15 ns, the device will support t nrp = ru{ t rp / t ck.avg } = 5, i.e. as long as the input cloc k jitter specifications are met, prechar ge command at tm and active command at tm + 5 is valid even if (tm + 5 - tm) is less than 15 ns due to input clock jitter. 35) t wtr is at lease two clocks (2 x t ck ) independent of operation frequency. parameter symbol ddr2?667 unit note 1)2)3)4)5)6)7) min. max. dq output access time from ck / ck t ac ?450 +450 ps 8) cas to cas command delay t ccd 2?nck average clock high pulse width t ch.avg 0.48 0.52 t ck.avg 9)10) average clock period t ck.avg 3000 8000 ps cke minimum pulse width ( high and low pulse width) t cke 3?nck 11) average clock low pulse width t cl.avg 0.48 0.52 t ck.avg 9)10) auto-precharge write recovery + precharge time t dal wr + t nrp ?nck 12)13) minimum time clocks remain on after cke asynchronously drops low t delay t is + t ck .avg + t ih ?? ns dq and dm input hold time t dh.base 175 ?? ps 18)19)14) dq and dm input pulse width for each input t dipw 0.35 ? t ck.avg dqs output access time from ck / ck t dqsck ?400 +400 ps 8) dqs input high pulse width t dqsh 0.35 ? t ck.avg dqs input low pulse width t dqsl 0.35 ? t ck.avg dqs-dq skew for dqs & associated dq signals t dqsq ? 240 ps 15) dqs latching rising transition to associated clock edges t dqss ? 0.25 + 0.25 t ck.avg 16) dq and dm input setup time t ds.base 100 ?? ps 17)18)19) dqs falling edge hold time from ck t dsh 0.2 ? t ck.avg 16) dqs falling edge to ck setup time t dss 0.2 ? t ck.avg 16) four activate window for 1kb page size products t faw 37.5 ? ns 34) four activate window for 2kb page size products t faw 50 ? ns 34) ck half pulse width t hp min( t ch.abs , t cl.abs ) __ ps 20) data-out high-impedance time from ck / ck t hz ? t ac.max ps 8)21) address and control input hold time t ih.base 275 ? ps 24)22)
internet data sheet rev. 1.2, 2007-05 49 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram control & address input pulse width for each input t ipw 0.6 ? t ck.avg address and control input setup time t is.base 200 ? ps 23)24) dq low impedance time from ck/ck t lz.dq 2x t ac.min t ac.max ps 8)21) dqs/dqs low-impedance time from ck / ck t lz.dqs t ac.min t ac.max ps 8)21) mrs command to odt update delay t mod 012ns 34) mode register set command cycle time t mrd 2?nck ocd drive mode output delay t oit 012ns 34) dq/dqs output hold time from dqs t qh t hp ? t qhs ?ps 25) dq hold skew factor t qhs ? 340 ps 26) average periodic refresh interval t refi ?7.8 s 27)28) ?3.9 s 28)29) auto-refresh to active/auto-refresh command period t rfc 127.5 ? ns 30) precharge-all (8 banks) command period t rp t rp +1 t ck ?ns read preamble t rpre 0.9 1.1 t ck.avg 31)32) read postamble t rpst 0.4 0.6 t ck.avg 31)33) active to active command period for 1kb page size products t rrd 7.5 ? ns 34) active to active command period for 2kb page size products t rrd 10 ? ns 34) internal read to precharge command delay t rtp 7.5 ? ns 34) write preamble t wpre 0.35 ? t ck.avg write postamble t wpst 0.4 0.6 t ck.avg write recovery time t wr 15 ? ns 34) internal write to read command delay t wtr 7.5 ? ns 34)35) exit power down to read command t xard 2?nck exit active power-down mode to read command (slow exit, lower power) t xards 7 ? al ? nck exit precharge power-down to any valid command (other than nop or deselect) t xp 2?nck exit self-refresh to a non-read command t xsnr t rfc +10 ? ns 34) exit self-refresh to read command t xsrd 200 ? nck write command to dqs associated clock edges wl rl?1 nck 1) v ddq = 1.8 v 0.1v; v dd = 1.8 v 0.1 v. 2) timing that is not specified is ille gal and after such an event, in order to guarantee proper operation, the dram must be pow ered down and then restarted through the specified initializa tion sequence before normal operation can continue. 3) timings are guaranteed with ck/ck differential slew rate of 2.0 v/ns. for dqs si gnals timings are guaranteed with a differential slew rate of 2.0 v/ns in differential strobe mode and a slew rate of 1 v/ns in single ended mode. 4) the ck / ck input reference level (for timing reference to ck / ck ) is the point at which ck and ck cross. the dqs / dqs , rdqs / rdqs , input reference level is the crosspoint when in differential st robe mode. the input reference level for signals other than ck/c k , dqs/dqs , rdqs / rdqs is defined. 5) inputs are not recognized as valid until v ref stabilizes. during the period before v ref stabilizes, cke = 0.2 x v ddq is recognized as low. 6) the output timing reference voltage level is v tt . parameter symbol ddr2?667 unit note 1)2)3)4)5)6)7) min. max.
internet data sheet rev. 1.2, 2007-05 50 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram 7) new units, ? t ck.avg ? and ?nck?, are introduced in ddr2?667 and ddr2?800. unit ? t ck.avg ? represents the actual t ck.avg of the input clock under operation. unit ?nck? represents one clock cycle of the i nput clock, counting the actual clock edges. note that in ddr2?4 00 and ddr2?533, ? t ck ? is used for both concepts. example: t xp = 2 [nck] means; if power down exit is registered at tm, an active command may be registered at tm + 2, even if (tm + 2 - tm) is 2 x t ck.avg + t err.2per(min) . 8) when the device is operated with input clock jitter, this parameter needs to be derated by the actual t err(6-10per) of the input clock. (output deratings are relative to the sdram input clock.) for example, if the measured jitter into a ddr2?667 sdram has t err(6-10per).min = ? 272 ps and t err(6- 10per).max = + 293 ps, then t dqsck.min(derated) = t dqsck.min ? t err(6-10per).max = ? 400 ps ? 293 ps = ? 693 ps and t dqsck.max(derated) = t dqsck.max ? t err(6-10per).min = 400 ps + 272 ps = + 672 ps. similarly, t lz.dq for ddr2?667 derates to t lz.dq.min(derated) = - 900 ps ? 293 ps = ? 1193 ps and t lz.dq.max(derated) = 450 ps + 272 ps = + 722 ps. (caution on the min/max usage!) 9) input clock jitter spec parameter. these parameters and the ones in chapter 7.3 are referred to as 'input clock jitter spec parameters' and these parameters apply to ddr2?667 and ddr2?800 only. the jitter spec ified is a random jitter m eeting a gaussian distribution. 10) these parameters are specified per thei r average values, however it is underst ood that the relationship as defined in chapter 7.3 between the average timing and the absolute instantaneous timing holds all th e times (min. and max of spec values are to be used for ca lculations of chapter 7.3 ). 11) t cke.min of 3 clocks means cke must be registered on three consecutive positive clock edges. cke must remain at the valid input level t he entire time it takes to achieve the 3 clo cks of registration. thus, after any cke tr ansition, cke may not transition from its v alid level during the time period of t is + 2 x t ck + t ih . 12) dal = wr + ru{ t rp (ns) / t ck (ns)}, where ru stands for round up. wr refers to the twr parameter stored in the mrs. for t rp , if the result of the division is not already an integer, round up to the next highest integer. t ck refers to the application clock period. example: for ddr2?533 at t ck = 3.75 ns with t wr programmed to 4 clocks. t dal = 4 + (15 ns / 3.75 ns) clocks = 4 + (4) clocks = 8 clocks. 13) t dal.nck = wr [nck] + t nrp.nck = wr + ru{ t rp [ps] / t ck.avg [ps] }, where wr is the value programmed in the emr. 14) input waveform timing t dh with differential data strobe enabled mr[bit10] = 0, is refe renced from the differential data strobe crosspoint to the input signal crossing at the v ih.dc level for a falling signal and from the differential data strobe crosspoint to the input signal crossing at the v il.dc level for a rising signal applied to the device under test. dqs, dqs signals must be monotonic between v il.dc.max and v ih.dc.min . see figure 9 . 15) t dqsq : consists of data pin skew and output pattern effects, and p-c hannel to n-channel variation of the output drivers as well as o utput slew rate mismatch between dqs / dqs and associated dq in any given cycle. 16) these parameters are measured from a data strobe signal ((l/u/r)dqs / dqs ) crossing to its respec tive clock signal (ck / ck ) crossing. the spec values are not affected by t he amount of clock jitter applied (i.e. t jit.per , t jit.cc , etc.), as these are relative to the clock signal crossing. that is, these param eters should be met whether clock jitter is present or not. 17) input waveform timing t ds with differential data strobe enabled mr[bit10] = 0, is referenced from the input signal crossing at the v ih.ac level to the differential data strobe crosspoint for a ri sing signal, and from the input signal crossing at the v il.ac level to the differential data strobe crosspoint for a falling signal applied to the device under test. dqs, dqs signals must be monotonic between v il(dc)max and v ih(dc)min . see figure 9 . 18) if t ds or t dh is violated, data corruption may occur and the data must be re -written with valid data before a valid read can be executed. 19) these parameters are measured from a data signal ((l/u)dm, (l/u)dq0, (l/u)dq1, etc.) transition edge to its respective data strobe signal ((l/u/r)dqs / dqs ) crossing. 20) t hp is the minimum of the absolute half period of the actual input clock. t hp is an input parameter but not an input specification parameter. it is used in conjunction with t qhs to derive the dram output timing t qh . the value to be used for t qh calculation is determined by the following equation; t hp = min ( t ch.abs , t cl.abs ), where, t ch.abs is the minimum of the actual instantaneous clock high time; t cl.abs is the minimum of the actual in stantaneous clock low time. 21) t hz and t lz transitions occur in the same access time as valid data trans itions. these parameters are refe renced to a specific voltage lev el which specifies when the device output is no longer driving ( t hz ), or begins driving ( t lz ) . 22) input waveform timing is referenced from the input signal crossing at the v il.dc level for a rising signal and v ih.dc for a falling signal applied to the device under test. see figure 10 . 23) input waveform timing is referenced from the input signal crossing at the v ih.ac level for a rising signal and v il.ac for a falling signal applied to the device under test. see figure 10 . 24) these parameters are measured from a command/address signal (c ke, cs, ras, cas, we, odt, ba0, a0, a1, etc.) transition edge to its respective clock signal (ck / ck ) crossing. the spec values are not affect ed by the amount of cl ock jitter applied (i.e. t jit.per , t jit.cc , etc.), as the setup and hold are relative to the clock signal cr ossing that latches the command/address. that is, these paramet ers should be met whether clock jitter is present or not. 25) t qh = t hp ? t qhs , where: t hp is the minimum of the absolute half period of the actual input clock; and t qhs is the specification value under the max column. {the less half-pulse width distortion present, the larger the t qh value is; and the larger the valid data eye will be.} examples: 1) if the system provides t hp of 1315 ps into a ddr2?667 sdram, the dram provides t qh of 975 ps minimum. 2) if the system provides t hp of 1420 ps into a ddr2?667 sdram, the dram provides t qh of 1080 ps minimum. 26) t qhs accounts for: 1) the pulse duration distortion of on-chip cloc k circuits, which represents how well the actual t hp at the input is transferred to the out put; and 2) the worst case push-out of dqs on one transition followed by th e worst case pull-in of dq on the next transition, both of wh ich are independent of each other, due to data pin skew, output pattern effects, and pchannel to n-channel variation of the output driv ers.
internet data sheet rev. 1.2, 2007-05 51 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram 27) the auto-refresh command interval has be reduced to 3.9 s when operating the ddr2 dram in a temperature range between 85 c and 95 c. 28) 0 c t case 85 c 29) 85 c < t case 95 c 30) a maximum of eight auto-refresh commands can be posted to any given ddr2 sdram device. 31) t rpst end point and t rpre begin point are not referenced to a specific voltage level but specify when the device output is no longer driving ( t rpst ), or begins driving ( t rpre ). figure 8 shows a method to calculate these points when the device is no longer driving ( t rpst ), or begins driving ( t rpre ) by measuring the signal at two different voltages. the actual voltage measurement poi nts are not critical as long as the calculation is consistent. 32) when the device is operated with i nput clock jitter, this parameter needs to be derated by the actual t jit.per of the input clock. (output deratings are relative to the sdram input clock.) for example, if the measured jitter into a ddr2?667 sdram has t jit.per.min = ? 72 ps and t jit.per.max = + 93 ps, then t rpre.min(derated) = t rpre.min + t jit.per.min = 0.9 x t ck.avg ? 72 ps = + 2178 ps and t rpre.max(derated) = t rpre.max + t jit.per.max = 1.1 x t ck.avg + 93 ps = + 2843 ps. (caution on the min/max usage!). 33) when the device is operated with i nput clock jitter, this parameter needs to be derated by the actual t jit.duty of the input clock. (output deratings are relative to the sdram input clock.) for ex ample, if the measured jitter into a ddr2?667 sdram has t jit.duty.min = ? 72 ps and t jit.duty.max = + 93 ps, then t rpst.min(derated) = t rpst.min + t jit.duty.min = 0.4 x t ck.avg ? 72 ps = + 928 ps and t rpst.max(derated) = t rpst.max + t jit.duty.max = 0.6 x t ck.avg + 93 ps = + 1592 ps. (caution on the min/max usage!). 34) for these parameters, the ddr2 sdram device is characterized and verified to support t nparam = ru{ t param / t ck.avg }, which is in clock cycles, assuming all input cl ock jitter specifications are satisfied. for example, the device will support t nrp = ru{ t rp / t ck.avg }, which is in clock cycles, if all input clock jitter specifications are me t. this means: for ddr2?667 5?5?5, of which t rp = 15 ns, the device will support t nrp = ru{ t rp / t ck.avg } = 5, i.e. as long as the input cloc k jitter specifications are met, prechar ge command at tm and active command at tm + 5 is valid even if (tm + 5 - tm) is less than 15 ns due to input clock jitter. 35) t wtr is at lease two clocks (2 x t ck ) independent of operation frequency.
internet data sheet rev. 1.2, 2007-05 52 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram figure 8 method for calculating transitions and endpoint figure 9 differential input waveform timing - t ds and t ds figure 10 differential input waveform timing - t ls and t lh w+= w53 6 7 hq gsr l q w 7 7 92 +[p 9 92 +[p 9 92 / [p 9 92 / [p 9 w/= w5 35( ehj l q srlqw 7 7 977 [p9 977 [p9 977 [ p9 977 [p9 w/= w53 5 ( ehjl qsrl qw 7 7 w+=w53 6 7 hq gsrl qw 7 7 w' 6 9 '' 4 9 ,+d f pl q 9 ,+g f pl q 9 5()gf 9 ,/ g f pd [ 9 ,/ d f pd [ 9 66 '4 6 '46 w'+ w'6 w'+ w,6 9 '' 4 9 ,+ d f plq 9 ,+ g f plq 9 5()gf 9 ,/ g f pd [ 9 ,/ d f pd [ 9 66 &. &. w, + w, 6 w, +
internet data sheet rev. 1.2, 2007-05 53 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram table 52 dram component timing parameter by speed grade - ddr2?533 parameter symbol ddr2?533 unit note 1)2)3)4)5) 6) min. max. dq output access time from ck / ck t ac ?500 +500 ps cas a to cas b command period t ccd 2? t ck ck, ck high-level width t ch 0.45 0.55 t ck cke minimum high and low pulse width t cke 3? t ck ck, ck low-level width t cl 0.45 0.55 t ck auto-precharge write recovery + precharge time t dal wr + t rp ? t ck 7)17) minimum time clocks remain on after cke asynchronously drops low t delay t is + t ck + t ih ?? ns 8) dq and dm input hold time (differential data strobe) t dh (base) 225 ?? ps 9) dq and dm input hold time (single ended data strobe) t dh1 (base) ?25 ? ps 10) dq and dm input pulse width (each input) t dipw 0.35 ? t ck dqs output access time from ck / ck t dqsck ?450 + 450 ps dqs input low (high) pulse width (write cycle) t dqsl,h 0.35 ? t ck dqs-dq skew (for dqs & associated dq signals) t dqsq ? 300 ps 10) write command to 1st dqs latching transition t dqss ? 0.25 + 0.25 t ck dq and dm input setup time (differential data strobe) t ds (base) 100 ? ps 10) dq and dm input setup time (single ended data strobe) t ds1 (base) ?25 ? ps 10) dqs falling edge hold time from ck (write cycle) t dsh 0.2 ? t ck dqs falling edge to ck setup time (write cycle) t dss 0.2 ? t ck four activate window period t faw 37.5 ? ns four activate window period t faw 50 ? ns 12) clock half period t hp min. ( t cl, t ch ) 11) data-out high-impedance time from ck / ck t hz ? t ac.max ps 12) address and control input hold time t ih (base) 375 ? ps 10) address and control input pulse width (each input) t ipw 0.6 ? t ck address and control input setup time t is (base) 250 ? ps 10) dq low-impedance time from ck / ck t lz(dq) 2 t ac.min t ac.max ps 13) dqs low-impedance from ck / ck t lz(dqs) t ac.min t ac.max ps 13) mrs command to odt update delay t mod 012ns mode register set command cycle time t mrd 2? t ck ocd drive mode output delay t oit 012ns
internet data sheet rev. 1.2, 2007-05 54 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram data output hold time from dqs t qh t hp ? t qhs ? data hold skew factor t qhs ? 400 ps average periodic refresh interval t refi ?7.8 s 13)14) average periodic refresh interval t refi ?3.9 s 15)17) auto-refresh to active/auto-refresh command period t rfc 127.5 ? ns 16) precharge-all (8 banks) command period t rp t rp +1 t ck ?ns read preamble t rpre 0.9 1.1 t ck 13) read postamble t rpst 0.40 0.60 t ck 13) active bank a to active bank b command period t rrd 7.5 ? ns 13)17) active bank a to active bank b command period t rrd 10 ? ns 15)21) internal read to precharge command delay t rtp 7.5 ? ns write preamble t wpre 0.25 ? t ck write postamble t wpst 0.40 0.60 t ck 18) write recovery time for write without auto- precharge t wr 15 ? ns internal write to read command delay t wtr 7.5 ? ns 19) exit power down to any valid command (other than nop or deselect) t xard 2? t ck 20) exit active power-down mode to read command (slow exit, lower power) t xards 6 ? al ? t ck 20) exit precharge power-down to any valid command (other than nop or deselect) t xp 2? t ck exit self-refresh to non-read command t xsnr t rfc +10 ? ns exit self-refresh to read command t xsrd 200 ? t ck write recovery time for write with auto- precharge wr t wr / t ck ? t ck 21) 1) v ddq = 1.8 v 0.1 v; v dd = 1.8 v 0.1 v. 2) timing that is not specified is ille gal and after such an event, in order to guarantee proper operation, the dram must be pow ered down and then restarted through the specified initializa tion sequence before normal operation can continue. 3) timings are guaranteed with ck/ck differential slew rate of 2.0 v/ns. for dqs si gnals timings are guaranteed with a differential slew rate of 2.0 v/ns in differential strobe mode and a slew rate of 1 v/ns in single ended mode. 4) the ck / ck input reference level (for timing reference to ck / ck ) is the point at which ck and ck cross. the dqs / dqs , rdqs / rdqs , input reference level is the crosspoint when in differential st robe mode. the input reference level for signals other than ck/c k , dqs/dqs , rdqs / rdqs is defined. 5) inputs are not recognized as valid until v ref stabilizes. during the period before v ref stabilizes, cke = 0.2 x v ddq is recognized as low. 6) the output timing reference voltage level is v tt . 7) for each of the terms, if not already an integer, round to the next highest integer. t ck refers to the application clock period. wr refers to the wr parameter stored in the mr. 8) the clock frequency is allowed to change during self-refresh mode or precharge power-down mode. 9) for timing definition, refer to the component data sheet. 10) consists of data pin skew and output pattern effects, and p-c hannel to n-channel variation of t he output drivers as well as output slew rate mis-match between dqs / dqs and associated dq in any given cycle. parameter symbol ddr2?533 unit note 1)2)3)4)5) 6) min. max.
internet data sheet rev. 1.2, 2007-05 55 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram table 53 dram component timing parameter by speed grade - ddr2-400 11) min ( t cl , t ch ) refers to the smaller of the actual clock low time and the act ual clock high time as provided to the device (i.e. this value can be greater than the minimum specification limits for t cl and t ch ). 12) the t hz , t rpst and t lz , t rpre parameters are referenced to a specific voltage level, which specify when the device output is no longer driving ( t hz, t rpst ), or begins driving ( t lz, t rpre ). t hz and t lz transitions occur in the same access time windows as valid da ta transitions.these parameters are verified by design and characteri zation, but not subject to production test. 13) the auto-refresh command interval has be reduced to 3.9 s when operating the ddr2 dram in a temperature range between 85 c and 95 c. 14) 0 c t case 85 c 15) 85 c < t case 95 c 16) a maximum of eight auto-refresh commands can be posted to any given ddr2 sdram device. 17) the t rrd timing parameter depends on the page size of the dram organization. see table 5 ?ordering information for lead-free products (rohs compliant)? on page 6 . 18) the maximum limit for the t wpst parameter is not a device limit. t he device operates with a greater value for this parameter, but system performance (bus turnaround) degrades accordingly. 19) minimum t wtr is two clocks when operating the ddr2-sdram at frequencies 200 ? z. 20) user can choose two different active pow er-down modes for additional power saving vi a mrs address bit a12. in ?standard acti ve power- down mode? (mr, a12 = ?0?) a fast power-down exit timing t xard can be used. in ?low active power-down mode? (mr, a12 =?1?) a slow power-down exit timing t xards has to be satisfied. 21) wr must be programmed to fulfill the minimum requirement for the t wr timing parameter, where wr min [cycles] = t wr (ns)/ t ck (ns) rounded up to the next integer value. t dal = wr + ( t rp / t ck ). for each of the terms, if not already an integer, round to the next highest integer. t ck refers to the application clock period. wr refers to the wr parameter stored in the mrs. parameter symbol ddr2?400 unit note 1)2)3)4)5) 6) min. max. dq output access time from ck / ck t ac ?600 +600 ps cas a to cas b command period t ccd 2? t ck ck, ck high-level width t ch 0.45 0.55 t ck cke minimum high and low pulse width t cke 3? t ck ck, ck low-level width t cl 0.45 0.55 t ck auto-precharge write recovery + precharge time t dal wr + t rp ? t ck 7)20) minimum time clocks remain on after cke asynchronously drops low t delay t is + t ck + t ih ?? ns 8) dq and dm input hold time (differential data strobe) t dh (base) 275 ?? ps 9) dq and dm input hold time (single ended data strobe) t dh1 (base) ?25 ? ps 10) dq and dm input pulse width (each input) t dipw 0.35 ? t ck dqs output access time from ck / ck t dqsck ?500 + 500 ps dqs input low (high) pulse width (write cycle) t dqsl,h 0.35 ? t ck dqs-dq skew (for dqs & associated dq signals) t dqsq ? 350 ps 10) write command to 1st dqs latching transition t dqss ? 0.25 + 0.25 t ck dq and dm input setup time (differential data strobe) t ds (base) 150 ? ps 10)
internet data sheet rev. 1.2, 2007-05 56 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram dq and dm input setup time (single ended data strobe) t ds1 (base) ?25 ? ps 10) dqs falling edge hold time from ck (write cycle) t dsh 0.2 ? t ck dqs falling edge to ck setup time (write cycle) t dss 0.2 ? t ck four activate window period t faw 37.5 ? ns four activate window period t faw 50 ? ns 12) clock half period t hp min. ( t cl, t ch ) 11) data-out high-impedance time from ck / ck t hz ? t ac.max ps 12) address and control input hold time t ih (base) 475 ? ps 10) address and control input pulse width (each input) t ipw 0.6 ? t ck address and control input setup time t is (base) 350 ? ps 10) dq low-impedance time from ck / ck t lz(dq) 2 t ac.min t ac.max ps 13) dqs low-impedance from ck / ck t lz(dqs) t ac.min t ac.max ps 13) mrs command to odt update delay t mod 012ns mode register set command cycle time t mrd 2? t ck ocd drive mode output delay t oit 012ns data output hold time from dqs t qh t hp ? t qhs ? data hold skew factor t qhs ? 450 ps average periodic refresh interval t refi ?7.8 s 13)14) average periodic refresh interval t refi ?3.9 s 15)17) auto-refresh to active/auto-refresh command period 127.5 ? ns 16) precharge-all (8 banks) command period t rp t rp +1 t ck ?ns read preamble t rpre 0.9 1.1 t ck 13) read postamble t rpst 0.40 0.60 t ck 13) active bank a to active bank b command period t rrd 7.5 ? ns 13)17) active bank a to active bank b command period t rrd 10 ? ns 15)21) internal read to precharge command delay t rtp 7.5 ? ns write preamble t wpre 0.25 ? t ck write postamble t wpst 0.40 0.60 t ck 18) write recovery time for write without auto- precharge t wr 15 ? ns internal write to read command delay t wtr 10 ? ns 19) exit power down to any valid command (other than nop or deselect) t xard 2? t ck 20) exit active power-down mode to read command (slow exit, lower power) t xards 6 ? al ? t ck 20) parameter symbol ddr2?400 unit note 1)2)3)4)5) 6) min. max.
internet data sheet rev. 1.2, 2007-05 57 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram exit precharge power-down to any valid command (other than nop or deselect) t xp 2? t ck exit self-refresh to non-read command t xsnr t rfc +10 ? ns exit self-refresh to read command t xsrd 200 ? t ck write recovery time for write with auto- precharge wr t wr / t ck ? t ck 21) 1) v ddq = 1.8 v 0.1 v; v dd = 1.8 v 0.1 v. 2) timing that is not specified is ille gal and after such an event, in order to guarantee proper operation, the dram must be pow ered down and then restarted through the specified initializa tion sequence before normal operation can continue. 3) timings are guaranteed with ck/ck differential slew rate of 2.0 v/ns. for dqs si gnals timings are guaranteed with a differential slew rate of 2.0 v/ns in differential strobe mode and a slew rate of 1 v/ns in single ended mode. 4) the ck / ck input reference level (for timing reference to ck / ck ) is the point at which ck and ck cross. the dqs / dqs , rdqs / rdqs , input reference level is the crosspoint when in differential st robe mode. the input reference level for signals other than ck/c k , dqs/dqs , rdqs / rdqs is defined. 5) inputs are not recognized as valid until v ref stabilizes. during the period before v ref stabilizes, cke = 0.2 x v ddq is recognized as low. 6) the output timing reference voltage level is v tt . 7) for each of the terms, if not already an integer, round to the next highest integer. t ck refers to the application clock period. wr refers to the wr parameter stored in the mr. 8) the clock frequency is allowed to change during self-refresh mode or precharge power-down mode. 9) for timing definition, refer to the component data sheet. 10) consists of data pin skew and output pattern effects, and p-channel to n-channel variation of t he output drivers as well as output slew rate mis-match between dqs / dqs and associated dq in any given cycle. 11) min ( t cl , t ch ) refers to the smaller of the actual clock low time and the ac tual clock high time as provided to the device (i.e. this value can be greater than the minimum specification limits for t cl and t ch ). 12) the t hz , t rpst and t lz , t rpre parameters are referenced to a specific voltage level, which specify when the device output is no longer driving ( t hz, t rpst ), or begins driving ( t lz, t rpre ). t hz and t lz transitions occur in the same access time windows as valid da ta transitions.these parameters are verified by design and characteri zation, but not subject to production test. 13) the auto-refresh command interval has be reduced to 3.9 s when operating the ddr2 dram in a temperature range between 85 c and 95 c. 14) 0 c t case 85 c 15) 85 c < t case 95 c 16) a maximum of eight auto-refresh commands can be posted to any given ddr2 sdram device. 17) the t rrd timing parameter depends on the page size of the dram organization. see table 5 ?ordering information for lead-free products (rohs compliant)? on page 6 . 18) the maximum limit for the t wpst parameter is not a device limit. t he device operates with a greater value for this parameter, but system performance (bus turnaround) degrades accordingly. 19) minimum t wtr is two clocks when operating the ddr2-sdram at frequencies 200 ? z. 20) user can choose two different active power-down modes for addi tional power saving via mrs address bit a12. in ?standard acti ve power- down mode? (mr, a12 = ?0?) a fast power-down exit timing t xard can be used. in ?low active power-down mode? (mr, a12 =?1?) a slow power-down exit timing t xards has to be satisfied. 21) wr must be programmed to fulfill the minimum requirement for the t wr timing parameter, where wr min [cycles] = t wr (ns)/ t ck (ns) rounded up to the next integer value. t dal = wr + ( t rp / t ck ). for each of the terms, if not already an integer, round to the next highest integer. t ck refers to the application clock period. wr refers to the wr parameter stored in the mrs. parameter symbol ddr2?400 unit note 1)2)3)4)5) 6) min. max.
internet data sheet rev. 1.2, 2007-05 58 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram 7.3 jitter definition and clock jitter specification generally, jitter is defined as ?the short-term variation of a si gnal with respect to its ideal position in time?. the followin g table provides an overview of the terminology. table 54 average clock and jitter symbols and definition symbol parameter description units t ck.avg average clock period t ck.avg is calculated as the average clock period within any consecutive 200-cycle window: (1) n=200 ps t jit.per clock-period jitter t jit.per is defined as the largest deviation of any single t ck from t ck.avg : t jit.per = min/max of { t cki ? t ck.avg } where i = 1 to 200 t jit.per defines the single-period jitter when the dll is already locked. t jit.per is not guaranteed through final production testing. ps t jit (per, lck) clock-period jitter during dll-locking period t jit (per,lck) uses the same definition as t jit.per , during the dll-locking period only. t jit (per,lck) is not guaranteed through final production testing. ps t jit.cc cycle-to-cycle clock period jitter t jit.cc is defined as the absolute difference in clock period between two consecutive clock cycles: t jit.cc = max of abs{ t cki+1 ? t cki } t jit.cc defines the cycle- to- cycle jitt er when the dll is already locked. t jit.cc is not guaranteed through final production testing. ps t jit (cc, lck) cycle-to-cycle clock period jitter during dll-locking period t jit (cc,lck) uses the same definition as t jit.cc during the dll-locking period only. t jit (cc,lck) is not guaranteed through final production testing. ps t err.2per cumulative error across 2 cycles t err.2per is defined as the cumulative error across 2 consecutive cycles from t ck.avg : (2) n=2 for t err (2per) where i = 1 to 200 ps tck.avg 1 n --- - . tck j j1 = n ?? ?? ?? ?? = terr 2per () tck j ji = in1 ? + ?? ?? ?? ?? ntckavg () ? =
internet data sheet rev. 1.2, 2007-05 59 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram the following parameters are specified per their average values however, it is understood that the following relationship between the average timing and the absolut e instantaneous timing holds all the time. t err.nper cumulative error across n cycles t err.2per is defined as the cumulative error across n consecutive cycles from t ck.avg : (3) where, i = 1 to 200 and n=3 for t err.3per n = 4 for t err.4per n = 5 for t err.5per 6 n 10 for t err.6-10per 11 n 50 for t err.11-50per ps t ch.avg average high-pulse width t ch.avg is defined as the average high-pulse width, as calculated across any consecutive 200 high pulses: (4) n=200 t ck.avg t cl.avg average low-pulse width t cl.avg is defined as the average low-pulse width, as calculated across any consecutive 200 low pulses: (5) n=200 t ck.avg t jit.duty duty-cycle jitter t jit.duty = min/max of { t jit.ch , t jit.cl }, where: t jit.ch is the largest deviation of any single t ch from t ch.avg t jit.cl is the largest deviation of any single t cl from t cl.avg t jit.ch = { t chi - t ch.avg t ck.avg } where i=1 to 200 t jit.cl = { t cli - t cl.avg t ck.avg } where i=1 to 200 ps symbol parameter description units terr nper () tck j ji = in1 ? + ?? ?? ?? ?? ntckavg () ? = tch avg () 1 ntckavg () () --------------- -------------- ----------- . tch j j1 = n ?? ?? ?? ?? = tcl avg () 1 ntckavg () () ---------------- -------------- ---------- . tcl j j1 = n ?? ?? ?? ?? =
internet data sheet rev. 1.2, 2007-05 60 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram table 55 absolute jitter value definitions example: for ddr2-667, tch.abs(min) = (0.48 x 3000ps) ? 125 ps = 1315 ps = 0.438 x 3000 ps. table 56 shows clock-jitter specifications. table 56 clock-jitter specifications for ?667 and ?800 symbol parameter min. max. unit t ck.abs clock period t ck.avg(min) + t jit.per(min) t ck.avg(max) + t jit.per(max) ps t ch.abs clock high-pulse width t ch.avg(min) x t ck.avg(min) + t jit.duty(min) t ch.avg(max) x t ck.avg(max) + t jit.duty(max) ps t cl.abs clock low-pulse width t cl.avg(min) x t ck.avg(min) + t jit.duty(min) t cl.avg(max) x t ck.avg(max) + t jit.duty(max) ps symbol parameter ddr2 -667 ddr2 -800 unit min. max. min. max. t ck.avg average clock period nominal w/o jitter 3000 8000 2500 8000 ps t jit.per clock-period jitter ?125 +125 ?100 +100 ps t jit(per,lck) clock-period jitter during dll locking period ?100 +100 ?80 +80 ps t jit.cc cycle-to-cycle clock-period jitter ?250 +250 ?200 +200 ps t jit(cc,lck) cycle-to-cycle clock-period jitter during dll- locking period ?200 +200 ?160 +160 ps t err.2per cumulative error across 2 cycles ?175 +175 ?150 +150 ps t err.3per cumulative error across 3 cycles ?225 +225 ?175 +175 ps t err.4per cumulative error across 4 cycles ?250 +250 ?200 +200 ps t err.5per cumulative error across 5 cycles ?250 +250 ?200 +200 ps t err(6-10per) cumulative error across n cycles with n = 6 .. 10, inclusive ?350 +350 ?300 +300 ps t err(11-50per) cumulative error across n cycles with n = 11 .. 50, inclusive ?450 +450 ?450 +450 ps t ch.avg average high-pulse width 0.48 0.52 0.48 0.52 t ck.avg t cl.avg average low-pulse width 0.48 0.52 0.48 0.52 t ck.avg t jit.duty duty-cycle jitter ?125 +125 ?100 +100 ps
internet data sheet rev. 1.2, 2007-05 61 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram 7.4 odt ac electrical characteristics this chapter describes the odt ac electrical characteristics. table 57 odt ac characteristics and operating conditions for ddr2-533 and ddr2-400 table 58 odt ac characteristics and operating conditions for ddr2-667 and ddr2-800 symbol parameter / condition values unit note min. max. t aond odt turn-on delay 2 2 t ck t aon odt turn-on t ac.min t ac.max + 1 ns ns 1) 1) odt turn on time min. is when the devic e leaves high impedance and odt re sistance begins to turn on. odt turn on time max is when the odt resistance is fully on. both are measured from t aond , which is interpreted differently per speed bin. for ddr2-400/533, t aond is 10 ns (= 2 x 5 ns) after the clock edge that registered a first odt high if t ck = 5 ns. t aonpd odt turn-on (power-down modes) t ac.min + 2 ns 2 t ck + t ac.max + 1 ns ns t aofd odt turn-off delay 2.5 2.5 t ck t aof odt turn-off t ac.min t ac.max + 0.6 ns ns 2) 2) odt turn off time min. is when the device starts to turn off odt resistance. odt turn off time max is when the bus is in high impedance. both are measured from t aofd . both are measured from t aofd , which is interpreted differently per speed bin. for ddr2-400/533, t aofd is 12.5 ns (= 2.5 x 5 ns) after the clock edge that registered a first odt high if t ck = 5 ns. t aofpd odt turn-off (power-down modes) t ac.min + 2 ns 2.5 t ck + t ac.max + 1 ns ns t anpd odt to power down mode entry latency 3 ? t ck t axpd odt power down exit latency 8 ? t ck symbol parameter / condition values unit note min. max. t aond odt turn-on delay 2 2 n ck 1) 1) new units, ?t ck.avg ? and ? n ck ?, are introduced in ddr2-667 and ddr2-800. unit ? t ck.avg ? represents the actual t ck.avg of the input clock under operation. unit ? n ck ? represents one clock cycle of the input clock, count ing the actual clock edges. note that in ddr2-400 and ddr2-533, ? t ck ? is used for both concepts. example: t xp = 2 [ n ck ] means; if power down exit is registered at t m , an active command may be registered at t m + 2, even if ( t m + 2 - t m ) is 2 x t ck.avg + t err.2per(min) . t aon odt turn-on t ac.min t ac.max + 0.7 ns ns 1)2) 2) odt turn on time min is when the device leaves high impedance and odt re sistance begins to turn on. odt turn on time max is w hen the odt resistance is fully on. both are measured from t aond , which is interpreted differently per speed bin. for ddr2-667/800, t aond is 2 clock cycles after the clock edge that registered a firs t odt high counting the actual input clock edges. t aonpd odt turn-on (power-down modes) t ac.min + 2 ns 2 t ck + t ac.max + 1 ns ns 1) t aofd odt turn-off delay 2.5 2.5 n ck 1) t aof odt turn-off t ac.min t ac.max + 0.6 ns ns 1)3) 3) odt turn off time min is when the device starts to turn off od t resistance. odt turn off time max is when the bus is in high impedance. both are measured from t aofd , which is interpreted differently per speed bin. for ddr2-667/800, if t ck(avg) = 3 ns is assumed, t aofd is 1.5 ns (= 0.5 x 3 ns) after the second trai ling clock edge counting from the clock edge t hat registered a first odt low and by coun ting the actual input clock edges. t aofpd odt turn-off (power-down modes) t ac.min + 2 ns 2.5 t ck + t ac.max + 1 ns ns 1) t anpd odt to power down mode entry latency 3 ? n ck 1) t axpd odt power down exit latency 8 ? n ck 1)
internet data sheet rev. 1.2, 2007-05 62 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram 8 package dimensions this chapter describes the package dimensions. figure 11 package outline p(g)-tfbga-84 notes 1. drawing according to iso 8015 2. dimensions in mm 3. general tolerances +/- 0.15 [ $ % ? ? ? 0 ? [ 0 & $% 0$; 0,1 & 6($7,1* 3/$1( 0lggoh ri sdfndjhv hgjhv %dg xqlw pdunlqj %80 (psw\ edoo sdgv iru rswlrqdo vxssruwlqj vroghu edoov [ 3dfndjh rulhqwdwlrq pdun $ 'xpp\ sdgv zlwkrxw edoo [ 0$; & & 0$; )32b3*7)%*$bb & /hdg iuhh vroghu edoov juhhq vroghu edoov
internet data sheet rev. 1.2, 2007-05 63 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram figure 12 package outline p(g)-tfbga-68 notes 1. drawing according to iso 8015 2. dimensions in mm 3. general tolerances +/- 0.15 [ $ % ? ? ? 0 ? [ 0 & $% 0$; 0,1 & 6($7,1* 3/$1( 0lggoh ri sdfndjhv hgjhv %dg xqlw pdunlqj %80 3dfndjh rulhqwdwlrq pdun $ 'xpp\ sdgv zlwkrxw edoo [ 0$; & & 0$; )32b3*7)%*$bb &
internet data sheet rev. 1.2, 2007-05 64 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram 9 product nomenclature for reference the qimonda sdram component nomenclature is enclosed in this chapter. table 59 examples for nomenclature fields table 60 ddr2 memory components example for field number 1234567891011 ddr2 sdram hyb 18 t 1g 40 0 a f ?3 ddr2 sdram hyb 18 t 1g 16 0 b f l ?3.7 field description values coding 1 qimonda component prefix hyb memory components hyi memory components, industrial temperature range (-40c ? +85 c) 2 interface voltage [v] 18 sstl_18 3 dram technology t ddr2 4 component density [mbit] 256 256 mbit 512 512 mbit 1g 1 gbit 2g 2 gbit 5+6 number of i/os 40 4 80 8 16 16 7 product variations 0 .. 9 look up table 8 die revision a(0 ..9) first b(0 ..9) second c(0 ..9) third 9 package, lead-free status c fbga, lead-containing f fbga, lead-free 10 power ? standard power product l low power product
internet data sheet rev. 1.2, 2007-05 65 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram 11 speed grade ?1.9 ddr2?1066 ?25f ddr2?800 5?5?5 ?2.5 ddr2?800 6?6?6 ?3 ddr2?667 4?4?4 ?3s ddr2?667 5?5?5 ?3.7 ddr2?533 4?4?4 ?5 ddr2?400 3?3?3 field description values coding
internet data sheet rev. 1.2, 2007-05 66 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram figure 1 ball configuration for 4 components, pg-tfbga-68 (top view). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 figure 2 ball configuration for 8 components, pg-tfbga-68 (top view). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 figure 3 chip configuration for x16 components in pg?tfbga?84 (top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 figure 4 single-ended ac input test conditions diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 figure 5 differential dc and ac input and output logic levels diagr am . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 figure 6 ac overshoot / undershoot diagram for address and control pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 figure 7 ac overshoot / undershoot diagram for clock, data, strobe and mask pins . . . . . . . . . . . . . . . . . . . . . . . . . 38 figure 8 method for calculating transitions and endpoint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 figure 9 differential in put waveform timing - t ds and t ds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 figure 10 differential input waveform timing - t ls and t lh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 figure 11 package outline p(g)-tfbga-84. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 figure 12 package outline p(g)-tfbga-68. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 list of figures
internet data sheet rev. 1.2, 2007-05 67 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram table 1 performance tables for ?2.5(f) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 table 2 performance table for ?3(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 table 3 performance table for ?3.7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 table 4 performance table for ?5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 table 5 ordering information for lead-free products (rohs compliant). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 table 6 ordering information for lead-containing products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 table 7 chip configuration of ddr2 sdram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 table 8 abbreviations for ball type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 table 9 abbreviations for buffer type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 table 10 chip configuration of ddr sdram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 table 11 abbreviations for ball type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 table 12 abbreviations for buffer type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 table 13 ddr2 addressing for 4 organization. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 table 14 ddr2 addressing for 8 organization. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 table 15 ddr2 addressing for 16 organization. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 table 16 mode register definition (ba[2:0] = 000b). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 table 17 extended mode register definition (ba[2:0] = 001 b ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 table 18 emrs(2) programming extended m ode register definition (ba[2:0]=010 b ) . . . . . . . . . . . . . . . . . . . . . . . . . . 23 table 19 emr(3) programming extended mode register definition(ba[2:0]=011 b ) . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 table 20 odt truth table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 table 21 burst length and sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 table 22 command truth table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 table 23 clock enable (cke) truth table for synchronous transitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 table 24 data mask (dm) truth table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 table 25 absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 table 26 dram component operating temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 table 27 recommended dc operating conditions (sstl_18) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 table 28 odt dc electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 table 29 input and output leakage currents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 table 30 dc & ac logic input levels for ddr2-667 and ddr2-800 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 table 31 dc & ac logic input levels for ddr2-533 and ddr2-400 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 table 32 single-ended ac input test condition s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 table 33 differential dc and ac input and output logic levels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 table 34 sstl_18 output dc current drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 table 35 sstl_18 output ac test conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 table 36 ocd default characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 table 37 input / output capacitance for ddr2-800 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 table 38 input / output capacitance for ddr2-667 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 table 39 input / output capacitance for ddr2-533 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 table 40 input / output capacitance for ddr2-400 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 table 41 ac overshoot / undershoot specification for address and co ntrol pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 table 42 ac overshoot / undershoot spec. for clock, data, strobe and mask pins . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 table 43 i dd measurement conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 table 44 definition for i dd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 table 45 i dd specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 table 46 speed grade definition speed bins for ddr2?800 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 table 47 speed grade definition speed bins for ddr2?667 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 table 48 speed grade definition speed bins for ddr2?533c. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 table 49 speed grade definition speed bins for ddr2-400b . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 list of tables
internet data sheet rev. 1.2, 2007-05 68 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram table 50 dram component timing parameter by speed grade - ddr2?800 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 table 51 dram component timing parameter by speed grade - ddr2?667 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 table 52 dram component timing parameter by speed grade - ddr2?533 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 table 53 dram component timing parameter by speed grade - ddr2-400. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 table 54 average clock and jitter symbols and definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 table 55 absolute jitter value definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 table 56 clock-jitter specifications for ?667 and ?800 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 table 57 odt ac characteristics and operating conditions for ddr2-533 and ddr2-400 . . . . . . . . . . . . . . . . . . . . . 61 table 58 odt ac characteristics and operating conditions for ddr2-667 and ddr2-800 . . . . . . . . . . . . . . . . . . . . . 61 table 59 examples for nomenclature fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 table 60 ddr2 memory components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
internet data sheet rev. 1.2, 2007-05 69 03062006-znh8-hurv hy[b/i]18t1g[40/80/16]0b[c/f](l) 1-gbit double-data-rate-two sdram 1 overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.1 features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.2 description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2 configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2.1 chip configuration for pg-tfbga-68 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2.2 chip configuration for pg-tfbga-84 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 2.3 1-gbit ddr2 addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 3 functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 4truth tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 5 electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 5.1 absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 5.2 dc characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 5.3 dc & ac characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 5.4 output buffer characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 5.5 input / output capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 5.6 overshoot and undershoot specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 6 currents measurement conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 7 timing characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 7.1 speed grade definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 7.2 component ac timing parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 7.3 jitter definition and clock jitter specif ication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 7.4 odt ac electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 8 package dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 9 product nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 table of contents
edition 2007-05 published by qimonda ag gustav-heinemann-ring 212 d-81739 mnchen, germany ? qimonda ag 2007. all rights reserved. legal disclaimer the information given in this internet data sheet shall in no ev ent be regarded as a guarantee of conditions or characteristics (?beschaffenheitsgarantie?). with respect to any examples or hi nts given herein, any typical values stated herein and/or any information regarding the application of the device, qimonda hereby disclaims any and all warranties and liabilities of any kin d, including without limitation warranties of non-infringem ent of intellectual property rights of any third party. information for further information on technology, delivery terms and conditio ns and prices please contact your nearest qimonda office. warnings due to technical requirements components may contain dangerous substances. for information on the types in question please contact your nearest qimonda office. qimonda components may only be used in life-support devices or systems with the express writte n approval of qimonda, if a failure of such components can reasonably be expected to cause the failure of that life-support devi ce or system, or to affect the safety or effectiveness of that device or system. life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain and/or protect human life. if they fail, it is re asonable to assume that the he alth of the user or other persons may be endangered. www.qimonda.com internet data sheet

▲Up To Search▲

Price & Availability of HYB18T1G160BF-25F

	To Download HYB18T1G160BF-25F Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .