1-44 h t-1 3 / 4 (5 mm) high performance ts algaas red led lamps technical data package dimensions hlmp-8100 hlmp-8102/-8103 HLMP-C100/-c110 23.0 (0.90) min. 1.27 (0.050) nom. 4.82 0.25 (0.190 0.010) 8.80 0.38 (0.347 0.015) 12.3 0.5 (0.485 0.020) 1.17 0.15 (0.046 0.006) 0.76 0.13 (0.030 0.005) 5.80 0.30 (0.228 0.012) cathode 2.54 (0.100) nom. 0.64 (0.025) square nominal 23.0 (0.90) min. 1.27 (0.050) nom. 4.82 0.25 (0.190 0.010) 8.80 0.38 (0.347 0.015) 11.3 0.5 (0.445 0.020) 1.17 0.15 (0.046 0.006) 0.76 0.13 (0.030 0.005) 5.80 0.30 (0.228 0.012) cathode 2.54 (0.100) nom. 0.64 (0.025) square nominal notes: 1. all dimensions are in millimeters/inches. 2. the leads are mild steel, solder dipped. 3. an epoxy meniscus may extend about 1 mm (0.040") down the leads, unless otherwise noted. 5.00 0.20 (0.197 0.008) 1.27 (0.050) nom. 1.14 0.20 (0.045 0.008) 8.70 0.20 (0.343 0.008) 5.80 0.20 (0.228 0.008) 2.35 (0.093) max. 0.70 (0.028) max. 0.50 0.10 (0.020 0.004) square cathode cathode 2.54 (0.100) nom. 31.4 (1.23) min. features ? exceptional brightness ? outstanding led material efficiency ? high light output over a wide range of drive currents ? viewing angle: narrow or wide ? low forward voltage ? low power dissipation ? cmos/mos compatible ? red color description these t-1 3 / 4 , untinted, nondiffused lamps utilize a highly optimized led material technology, transparent substrate aluminum gallium arsenide (ts algaas). this led technology has a very high luminous efficiency, capable of producing high light output over a wide range of drive currents (500 m a to 50 ma). the color is deep red at a dominant wave- length of 644 nm. ts algaas is a flip-chip led technology, die attached to the anode lead and wire bonded to the cathode lead. hlmp-810x series HLMP-C100 hlmp-c110 5964-9291e
1-45 axial luminous intensity and viewing angle at t a = 25 c typical radiant part number minimum intensity typical intensity intensity 2 q 1 / 2 [1] hlmp- (mcd) @ 20 ma (mcd) @ 20 ma (mw/sr) @ 20 ma degrees 8103 2000 3000 35.3 7 8102 1400 2000 23.5 7 8100 290 1000 11.8 19 c100 290 750 8.8 30 c110 200 400 4.7 40 note: 1. q 1/2 is the off axis angle from optical centerline where the luminous intensity is 1/2 the on-axis value. absolute maximum ratings at t a = 25 c peak forward current [2] .......................................................... 300 ma average forward current (@ i peak = 300 ma) [1,2] ................... 30 ma dc forward current [3] ............................................................... 50 ma power dissipation .................................................................... 100 mw reverse voltage (i r =100 m a) ........................................................... 5 v transient forward current (10 m s pulse) [4] ............................ 500 ma operating temperature range ...................................... -55 to +100 c storage temperature range .......................................... -55 to +100 c led junction temperature ....................................................... 110 c lead soldering temperature [1.6 mm (0.063 in.) from body] .......................... 260 c for 5 seconds notes: 1. maximum i avg at f = 1 khz, df = 10%. 2. refer to figure 6 to establish pulsed operating conditions. 3. derate linearly as shown in figure 5. 4. the transient peak current is the maximum non-recurring peak current the device can withstand without damaging the led die and wire bonds. it is not recommended that the device be operated at peak currents above the absolute maximum peak forward current.
1-46 electrical/optical characteristics at t a = 25 c description symbol min. typ. max. units test conditions forward voltage v f 1.85 2.4 v i f = 20 ma reverse voltage v r 5.0 20.0 v i r = 100 m a peak wavelength l peak 654 nm dominant wavelength [1] l d 644 nm spectral line halfwidth dl 1/2 18 nm speed of response t s 45 ns exponential time constant, e -t/ t capacitance c 20 pf v f = 0, f = 1 mhz thermal resistance hlmp-810x r q j-pin 210 c/w junction-to-anode lead hlmp-c1x0 237 luminous efficacy [2] h v 85 lm/w notes: 1. the dominant wavelength, l d , is derived from the cie chromaticity diagram and represents the color of the device. 2. the radiant intensity, i e , in watts per steradian, may be found from the equation i e =i v / h v , where i v is the luminous intensity in candelas and h v is luminous efficacy in lumens/watt figure 1. relative intensity vs. wavelength. figure 2. forward current vs. forward voltage. 1.0 10 -1 10 -2 10 -3 500 600 700 1000 relative intensity wavelength - nm v - forward voltage - v f i - forward current - ma f 200 100 50 20 10 5 2 1 0 0.5 1.0 1.5 2.0 2.5 3.0 300 3.5
1-47 figure 7. relative luminous intensity vs. angular displacement. hlmp-8103 and hlmp-8102. q ?angle from optical centerline ?degrees (cone half angle) relative luminous intensity 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 100 90 80 70 60 50 40 30 20 10 0 10 20 30 40 50 60 70 80 90 100 figure 4. relative efficiency vs. peak forward current. figure 3. relative luminous intensity vs. dc forward current. 1.1 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 1 2 5 10 20 50 100 300 h - relative efficiency (normalized at 20 ma) v i - peak forward current - ma peak 1.2 200 2.4 2.0 1.0 0.5 0.2 0.1 0.05 12 51020 50 relative luminous intensity (normalized at 20 ma) i - dc forward current - ma f 0.01 0.5 50 40 30 20 10 0 0 20 40 6080100 25 i - forward current - ma f r q = 400 c/w ja r q = 550 c/w ja t - ambient temperature - c a 55 50 40 20 10 0 50 200 250 100 i = average forward current ?ma avg i ?peak forward current ?ma peak 150 30 300 f 3 1000 hz f 3 300 hz f 3 100 hz figure 6. maximum average current vs. peak forward current. figure 5. maximum forward dc current vs. ambient temperature. derating based on tjmax = 110 c.
1-48 figure 9. relative luminous intensity vs. angular displacement. HLMP-C100. figure 8. relative luminous intensity vs. angular displacement. hlmp-8100. q ?angle from optical centerline ?degrees (cone half angle) relative luminous intensity 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 100 90 80 70 60 50 40 30 20 10 0 10 20 30 40 50 60 70 80 90 100 q ?angle from optical centerline ?degrees (cone half angle) relative luminous intensity 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 100 90 80 70 60 50 40 30 20 10 0 10 20 30 40 50 60 70 80 90 100 q ?angle from optical centerline ?degrees (cone half angle) relative luminous intensity 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 100 90 80 70 60 50 40 30 20 10 0 10 20 30 40 50 60 70 80 90 100 figure 10. relative luminous intensity vs. angular displacement. hlmp-c110.
|
