View XRT86VX38IB256_3409806.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

exar corporation 48720 kato road, fremont ca, 94538 ? (510) 668-7000 ? fax (510) 668-7017 ? www.exar.com xrt86vx38 8-channel t1/e1/j1 framer/liu combo - t1 register description 2009 rev. 1.0.1 general description the xrt86vx38 is an eight-channel 1.544 mbit/s or 2.048 mbit/s ds1/e1/j1 framer and long-haul/short- hual liu integrated solution featuring r 3 technology (relayless, reconfigurable, redundancy) and bits timing element. the physical interface is optimized with internal impedance, and with the patented pad structure, the xrt86vx38 provides protection from power failures and hot swapping. the xrt86vx38 contains an integrated ds1/e1/j1 framer and liu which provide ds1/e1/j1 framing and error accumulation in accordance with ansi/itu_t specifications. each framer has its own framing synchronizer and transmit-receive slip buffers. the slip buffers can be independently enabled or disabled as required and can be configured to frame to the common ds1/e1/j1 signal formats. each framer block contains its own transmit and receive t1/e1/j1 framing function. there are 3 transmit hdlc controlle rs per channel which encapsulate contents of the transmit hdlc buffers into lapd message frames. there are 3 receive hdlc controllers per channel which extract the payload content of receive lapd message frames from the incoming t1/e1/j1 data stream and write the contents into the receive hdlc buffers. each framer also contains a transmit and overhead data input port, which permits data link terminal equipment direct access to the outbound t1/e1/j1 frames. likewise, a receive overhead output data port permits data link terminal equipment direct access to the data link bits of the inbound t1/e1/j1 frames. the xrt86vx38 fully meets a ll of the latest t1/e1/j1 specifications: ansi t1/e1.107-1988, ansi t1/ e1.403-1995, ansi t1/e1.231-1993, ansi t1/ e1.408-1990, at&t tr 62411 (12-90) tr54016, and itu g-703, g.704, g706 and g.733, at&t pub. 43801, and ets 300 011, 300 233, jt g.703, jt g.704, jt g706, i.431. extensive test and diagnostic functions include loop-backs, boundary scan, pseudo random bit sequence (prbs) test pattern generation, performance monitor, bit error rate (ber) meter, forced error insertion, and lapd unchannelized data payload processing according to itu-t standard q.921. . applications and features (next page) f igure 1. xrt86vx38 e ight c hannel ds1 (t1/e1/j1) f ramer /liu c ombo performance monitor prbs generator & analyser hdlc/lapd controllers liu & loopback control dma interface signaling & alarms jtag wr ale_as rd rdy_dtack ? p select a[11:0] d[7:0] microprocessor interface 4 3 tx serial clock rx serial clock 8khz sync osc back plane 1.544-16.384 mbit/s local pcm highway st-bus 2-frame slip buffer elastic store tx serial data in tx liu interface 2-frame slip buffer elastic store rx liu interface rx framer rx serial data out rtip rring ttip tring external data link controller tx overhead in rx overhead out xrt86vx38 tx framer llb lb system (terminal) side line side 1:1 turns ratio 1:2 turns ratio memory intel/motorola p configuration, control & status monitor rxlos txon int
xrt86vx38 2 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 applications ? high-density t1/e1/j1 in terfaces for multiplexe rs, switches, lan routers and digital modems ? sonet/sdh terminal or add/ drop multiplexers (adms) ? t1/e1/j1 add/drop multiplexers (mux) ? channel service units (csus): t1/e1/j1 and fractional t1/e1/j1 ? bits timing ? digital access cross-connect system (dacs) ? digital cross-connect systems (dcs) ? frame relay switches and access devices (frads) ? isdn primary rate interfaces (pra) ? pbxs and pcm channel bank ? t3 channelized access concentrators and m13 mux ? wireless base stations ? atm equipment with inte grated ds1 interfaces ? multichannel ds1 test equipment ? t1/e1/j1 performance monitoring ? voice over packet gateways ? routers features ? supports section 13 - synchronization interface in itu g.703 for both transmit and receive paths ? supports ssm synchronous messaging generation (boc fo r t1, national bits for e1) on the transmit path ? supports ssm synchronous messaging extraction (boc fo r t1, national bits for e1) on the receive path ? supports bits timing generation on the transmit outputs ? supports bits timing extraction from nrz data on the analog receive path ? ds-0 monitoring on both transmit and receive time slots ? supports ssm synchronization messaging per ansi t1.101-1999 and itu g.704 ? supports a customized section 13 - synchronization interface in g.703 at 1.544mhz ? independent, full duplex ds1 tx and rx framer/lius ? each channel has full featured long-haul/short-haul liu ? two 512-bit (two-frame) elastic store, pcm frame slip bu ffers (fifo) on tx and rx provide up to 8.192 mhz asynchronous back plane connections with jitter and wander attenuation ? supports input pcm and signaling data at 1.544, 2.04 8, 4.096 and 8.192 mbits. also supports 2-channel multiplexed 12.352/16.384 (hmvip/h .100) mbit/s on the back plane bus ? programmable output clocks for fractional t1/e1/j1 ? supports channel associated signaling (cas) ? supports common channel signalling (ccs) ? supports isdn primary rate in terface (isdn pri) signaling
xrt86vx38 3 rev. 1.0.1 8-channel t1/e1/j1 framer/liu combo - t1 register description 8-channel t1/e1/j1 framer/ ? extracts and inserts robbed bit signaling (rbs) ? 3 integrated hdlc controllers for transmit and receive, each controller having two 96-byte buffers (buffer 0 / buffer 1) ? hdlc controllers support ss7 ? timeslot assignable hdlc ? v5.1 or v5.2 interface ? automatic performance report generation (pmon status) can be inserted into the transmit lapd interface every 1 second or for a single transmission ? supports sprm and nprm ? alarm indication signal with customer installation signature (ais-ci) ? remote alarm indication with cu stomer installation (rai-ci) ? gapped clock interface mode for transmit and receive. ? intel/motorola and power pc interfaces for configuration, control and status monitoring ? parallel search algorithm for fast frame synchronization ? wide choice of t1 framing structures: sf/d4, esf, slc ? 96, t1dm and n-frame (non-signaling) ? direct access to d and e c hannels for fast transmission of data link information ? full bert controller for generation and dete ction on system and line side of the chip ? prbs, qrss, and network loop code generation and detection ? seven independent, simultaneous loop code detectors per channel ? programmable interrupt output pin ? supports programmed i/o and dma modes of read-write access ? the framer block encodes and decodes the t1/e1/j1 frame serial data ? detects and forces red (sai), yellow (rai) and blue (ais) alarms ? detects oof, lof, los errors and cofa conditions ? loopbacks: local (llb) and line remote (lb) ? facilitates inverse mu ltiplexing for atm ? performance monitor wi th one second polling ? boundary scan (ieee 11 49.1) jtag test port ? accepts external 8khz sync reference ? 1.8v inner core ? 3.3v cmos operation wit h 5v tolerant inputs ? 256-pin fpbga and 329-pin fpbga package with -40 ? c to +85 ? c operation ordering information p art n umber p ackage o perating t emperature r ange XRT86VX38IB256 256 pin fine pitch ball grid array -40 ? c to +85 ? c xrt86vx38ib329 329 pin fine pitch ball grid array -40 ? c to +85 ? c
xrt86vx38 i 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 list of tables table 1:: register summary .................................................................................................... .......................................... 4 table 2:: clock select register(csr) hex addr ess: 0xn100 .......... 9 table 3:: line interface control register (licr) hex address: 0xn101 ............... 11 table 4:: framing select register (fsr) hex address: 0xn107 .. .................. 13 table 5:: alarm generation register (agr) hex address: 0xn108 ...... ............... 15 table 6:: yellow alarm duration and format when one second rule is not enforced ............................................... .......... 16 table 7:: yellow alarm format when one second rule is en forced ............... .............. .............. ........... .......... .................... 17 table 8:: synchronization mux register (smr) hex address: 0xn109 ....... ............ 19 table 9:: transmit signaling and data link select register (tsdlsr) hex address:0xn10a .................... 2 2 table 10:: framing control register (fcr) hex address: 0xn10b .. ................ 24 table 11:: receive signaling & data link select register (rsdlsr) hex address: 0xn10c .................... 2 5 table 12:: receive signaling change register 0 (rscr 0) hex address: 0xn10d ...... .... 27 table 13:: receive signaling change register 1(rscr 1) hex address: 0xn10e .. .... 27 table 14:: receive signaling change register 2 (rscr 2) hex address: 0xn10f .... .... 27 table 15:: receive in frame register (rifr) hex address: 0xn112 .... .............. 28 table 16:: data link control register (dlcr1) hex address: 0xn113 ...... .............. 28 table 17:: transmit data link byte count register (tdlbcr1) hex address: 0xn114 .................. .. 31 table 18:: receive data link byte count register (rdlbcr1) hex address: 0xn115 ................. .32 table 19:: slip buffer control register (sbcr) hex address: 0xn116 ...... ............... 33 table 20:: fifo latency register (ffolr) hex address: 0xn117 . ............... 34 table 21:: dma 0 (write) configuration register (d0wcr) hex address: 0xn118 ............. ..... 35 table 22:: dma 1 (read) configuration register (d1rcr) hex address: 0xn119 ............. .... 36 table 23:: interrupt control register (icr) hex address: 0xn11a ... ................... 37 table 24:: lapd select register (lapdsr) hex address: 0xn11b ... ............. 37 table 25:: customer installation al arm generation register (ciagr) hex address: 0xn11c ....................... 3 8 table 26:: performance report control register (prcr) hex address: 0xn11d ............... ..... 39 table 27:: gapped clock control register (gccr) hex address: 0xn11e ......... ......... 40 table 28:: transmit interface control regi ster (ticr) hex address:0xn120 ......... ........... 41 table 29:: transmit interface speed when multiplexed mode is disabled (txmuxen = 0) ........................................... 43 table 30:: transmit interface speed wh en multiplexed mode is enabled (txmuxen = 1) ........ .............. ............ .......... 44 table 31:: prbs control & status register (prbscsr0) hex address: 0xn121 ........... .... 45 table 32:: receive interface control register (ricr) hex address: 0xn122 ... ........... 47 table 33:: receive interface speed when multiplexed mode is disabled (txmuxen = 0) ............................................ 49 table 34:: receive interface speed when multiplexed mode is enabled (txmuxen = 1) ............................................. 50 table 35:: prbs control & status regist er (prbscsr1) hex address: 0xn123 ................. .... 51 table 36:: loopback code control register (lccr) hex address: 0xn124 ....... ......... 53 table 37:: transmit loopback coder register (tlcr) hex address: 0xn125 ...... ....... 55 table 38:: receive loopback activation code register (rlacr) hex address: 0x n126 ...... .......... 55 table 39:: receive loopback deactivation code register (rldcr) hex address: 0xn1 27 ........... ........ 55 table 40:: defect detection enable register (dder) hex address: 0xn129 ..... ......... 56 table 41:: transmit sprm control register (tsprmcr) hex address: 0xn142 ............. ... 56 table 42:: data link control register (dlcr2) hex address: 0xn143 ..... .............. 57 table 43:: transmit data link byte count register (tdlbcr2) hex address: 0xn144 ................. .. 59 table 44:: receive data link byte count register (rdlbcr2) hex address: 0xn145 ................ .60 table 45:: data link control register (dlcr3) hex address: 0xn153 .... .............. 61 table 46:: transmit data link byte count register (tdlbcr3) hex address: 0xn154 ................. .. 63 table 47:: receive data link byte count register (rdlbcr3) hex address: 0xn155 ................ .64 table 48:: device id register (devid) hex address: 0xn1fe ........... 65 table 49:: revision id register (revid) hex address: 0xn1ff .......... 65 table 50:: transmit channel control register 0-23 (tccr 0-23) hex a ddress: 0xn300 to 0x n317 ......... .......... 66 table 51:: transmit user code regist er 0-23 (tucr 0-23) hex address: 0xn320 to 0xn337 ............... 68 table 52:: transmit signaling control regi ster 0-23 (tscr 0-23) hex addr ess: 0xn340 to 0xn 357 ............ .......... 69 table 53:: receive channel control register 0-23 (rccr 0-23) hex address: 0x n360 to 0xn377 .......... ........ 71 table 54:: receive user code register 0-23 (rucr 0-23) hex addr ess: 0xn380 to 0x n397 ............. 73 table 55:: receive signaling control register 0-23 (rscr 0-23) hex address: 0xn3a0 to 0xn3b7 ................... 74 table 56:: receive substitution signaling register 0-23 (rssr 0-23) hex address: 0xn3c0 to 0xn3d7 .................. 76 table 57:: receive signaling array register 0 to 23 (rsar 0-23) hex address: 0xn500 to 0xn517 .................. 77 table 58:: lapd buffer 0 control register (lapdbcr0) hex address: 0xn600 .............................. ...... 78
xrt86vx38 ii rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description table 59:: lapd buffer 1 control register (lapdbcr1) hex address: 0xn700 ................................ ..... 78 table 60:: pmon receive line code violation counter msb (rlcvcu) hex address: 0xn900 ................ 79 table 61:: pmon receive line code violation counter lsb (rlcvcl) hex address: 0xn901 ................ 79 table 62:: pmon receive framing alignment bit error counte r msb (rfaecu) hex address: 0xn902 ................... 80 table 63:: pmon receive framing alignment bit error counte r lsb (rfaecl) hex address: 0xn903 ................... 80 table 64:: pmon receive severely errored fram e counter (rsefc) hex address: 0xn904 ...... ............ 81 table 65:: pmon receive crc-6 bit error counter - msb (rsbbecu) hex address: 0xn905 ........... ...... 82 table 66:: pmon receive crc-6 bit error counter - lsb (rsbbecl) he x address: 0xn906 .......... ...... 82 table 67:: pmon receive slip counter (rsc) hex address: 0xn909 ... ........... 83 table 68:: pmon receive loss of frame counter (rlfc) hex address: 0xn90a ............. .. 83 table 69:: pmon receive change of frame alignment counter (rcfac) hex address: 0xn90b ............... 83 table 70:: pmon lapd1 frame check sequence error counter 1 (lfcsec1) hex addr ess: 0xn90c .. ............ ... 84 table 71:: prbs bit error counter msb (pbecu) hex address: 0xn90d ......... ........ 84 table 72:: prbs bit error count er lsb (pbecl) hex address: 0xn90e ....... .......... 84 table 73:: transmit slip counter (tsc) hex address: 0xn 90f .............. 85 table 74:: excessive zero violation counter msb (ezvcu) hex address: 0xn910 ............. ... 85 table 75:: excessive zero violation counter lsb (ezvcl) hex address: 0xn911 ............ ..... 85 table 76:: pmon lapd2 frame check sequence error counter 2 (lfcsec2) hex addr ess: 0xn91c .. ............ ... 86 table 77:: pmon lapd2 frame check sequence error counter 3 (lfcsec3) hex addr ess: 0xn92c .. ............ ... 86 table 78:: block interrupt status register (bisr) hex address: 0xnb00 ...... .............. 87 table 79:: block interrupt enable register (bier) hex address: 0xnb01 ...... ............. 89 table 80:: alarm & error interrupt status register (aeisr) hex address: 0xnb02 ............. ....... 91 table 81:: alarm & error interrupt enable register (aeier) hex address: 0xnb03 ............... ...... 93 table 82:: framer interrupt status register (fisr) hex address: 0xnb04 ...... ............ 94 table 83:: framer interrupt enable register (fier) hex address: 0xnb05 ....... ........... 96 table 84:: data link status register 1 (dlsr1) hex address: 0xnb06 ... ............. 98 table 85:: data link interrupt enable register 1 (dlier1) hex address: 0xnb07 ........... ..... 100 table 86:: slip buffer interrupt status register (sbi sr) hex address: 0xnb08 .......... ......... 102 table 87:: slip buffer interrupt enable register (sbi er) hex address: 0xnb09 .......... ........ 105 table 88:: receive loopback code interrupt and status register (rlcisr) hex address: 0xnb 0a ........ .......... 107 table 89:: receive loopback code interrupt enabl e register (rlcier) hex address: 0x nb0b ........ .......... 108 table 90:: excessive zero status register (exzsr) hex address: 0xnb0e ......... ...... 109 table 91:: excessive zero enable register (exzer) hex address: 0xnb0f ........ ...... 109 table 92:: ss7 status register for lapd1 (ss7sr1) hex address: 0xnb10 .......... ..... 110 table 93:: ss7 enable register for lapd1 (ss7er1) hex address: 0xnb11 ......... .... 110 table 94:: rxlos/crc interrupt status register (rlcisr) hex address: 0xnb12 ............. .111 table 95:: rxlos/crc interrupt enable regist er (rlcier) hex address: 0xnb13 ....... ....... 111 table 96:: data link status register 2 (dlsr2) hex address: 0xnb16 .... ........... 112 table 97:: data link interrupt enable register 2 (dlier2) hex address: 0xnb17 ........... ..... 114 table 98:: ss7 status register for lapd2 (ss7sr2) hex address: 0xnb18 .......... ..... 116 table 99:: ss7 enable register for lapd2 (ss7er2) hex address: 0xnb19 ........... .... 116 table 100:: data link status register 3 (dlsr3) hex address: 0xnb26 ... .......... 117 table 101:: data link interrupt enable register 3 (dlier3) hex address: 0xnb27 ......... .... 119 table 102:: ss7 status register for lapd3 (ss7sr3) hex address: 0xnb28 ........ .... 121 table 103:: ss7 enable register for lapd3 (ss7er3) hex address: 0xnb29 ........ ... 121 table 104:: customer installation ala rm status register (ciasr) hex address: 0xnb40 ................. 122 table 105:: customer installation ala rm status register (ciaier) hex address: 0xnb41 ................. 123 table 106:: liu channel control register 0 (liuccr0) hex address: 0xnf00 ....... ..... 124 table 107:: equalizer control and transmit line build out ..................................................................... ...................... 126 table 108:: liu channel control register 1 (liuccr1) hex address: 0xnf01 ...... ..... 127 table 109:: liu channel control register 2 (liuccr2) hex address: 0xnf02 ....... ..... 129 table 110:: liu channel control register 3 (liuccr3) hex address: 0xnf03 ...... ..... 131 table 111:: liu channel control interrupt enable register (liuccier) hex address: 0xnf04 ................. 133 table 112:: liu channel control status register (li uccsr) hex address: 0xnf05 .............. .135 table 113:: liu channel control interrupt status register (liuccisr) hex address: 0xnf06 .................... 138 table 114:: liu channel control cable loss register (liuccccr) hex address: 0x nf07 ............... 139 table 115:: liu channel control arbitrary register 1 (liuccar1) hex address: 0xnf08 .................. 1 40 table 116:: liu channel control arbitrary regist er 2 (liuccar2) hex address: 0xnf09 ..................... 1 40 table 117:: liu channel control arbitrary register 3 (liuccar3) hex address: 0xnf0a .................... 14 0 table 120:: liu channel control arbitrary register 6 (liuccar6) hex address: 0xnf0d .................... 14 1
xrt86vx38 iii 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 table 118:: liu channel control arbitrary register 4 (liuccar4) hex address: 0xnf0b ..................... 1 41 table 119:: liu channel control arbitrary register 5 (liuccar5) hex address: 0xnf0c .................... 14 1 table 121:: liu channel control arbitrary register 7 (liuccar7) hex address: 0xnf0e ..................... 1 42 table 122:: liu channel control arbitrary register 8 (liuccar8) hex address: 0xnf0f ..................... 1 42 table 123:: liu global control register 0 (liugcr0) hex address: 0xnfe0 ...... ...... 143 table 124:: liu global control register 1 (liugcr1) hex address: 0xnfe1 ...... ...... 144 table 125:: liu global control register 2 (liugcr2) hex address: 0xnfe2 ...... ...... 145 table 126:: liu global control register 3 (liugcr3) hex address: 0xnfe4 ...... ...... 146 table 127:: liu global control register 4 (liugcr4) hex address: 0xnfe9 ...... ...... 147 table 128:: liu global control register 5 (liugcr5) hex address: 0xnfea ...... ...... 148
xrt86vx38 4 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description description of the control registers - t1 mode all address on this register description is shown in hex format. t able 1: r egister s ummary f unction s ymbol h ex control registers (0xn100 - 0xn1ff) clock and select register csr 0xn100 line interface control register licr 0xn101 reserved - 0xn102 - 0xn106 framing select register fsr 0xn107 alarm generation register agr 0xn108 synchronization mux register smr 0xn109 transmit signaling and data link select register tsdlsr 0xn10a framing control register fcr 0xn10b receive signaling & data link select register rsdlsr 0xn10c receive signaling change register 0 rscr0 0xn10d receive signaling change register 1 rscr1 0xn10e receive signaling change register 2 rscr2 0xn10f reserved - e1 mode only - 0xn110 - 0xn111 receive in-frame register rifr 0xn112 data link control register 1 dlcr1 0xn113 transmit data link byte count register 1 tdlbcr1 0xn114 receive data link byte count register 1 rdlbcr1 0xn115 slip buffer control register sbcr 0xn116 fifo latency register fifolr 0xn117 dma 0 (write) configuration register d0wcr 0xn118 dma 1 (read) configuration register d1rcr 0xn119 interrupt control register icr 0xn11a lapd select register lapdsr 0xn11b customer installation alarm generation register ciagr 0xn11c performance report control register prcr 0xn11d gapped clock control register gccr 0xn11e transmit interface control register ticr 0xn120 bert control & status - register 0 bertcsr0 0xn121 receive interface control register ricr 0xn122
xrt86vx38 5 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 bert control & status - register 1 bertcsr1 0xn123 loopback code control register - code 0 lccr0 0xn124 transmit loopback code register tlcr 0xn125 receive loopback activation code register - code 0 rlacr0 0xn126 receive loopback deactivation code register - code 0 rldcr0 0xn127 receive loopcode detection switch rlcds 0xn128 defect detection enable register dder 0xn129 loopback code control register - code 1 lccr1 0xn12a receive loopback activation code register - code 1 rlacr1 0xn12b receive loopback deactivation code register - code 1 rldcr1 0xn12c loopback code control register - code 2 lccr2 0xn12d receive loopback activation code register - code 2 rlacr2 0xn12e receive loopback deactivation code register - code 2 rldcr2 0xn12f reserved - e1 mode only - 0xn130 - 0xn13f transmit loopcode generation switch tlcgs 0xn140 loopcode timer select lcts 0xn141 transmit sprm and nprm control register tsprmcr 0xn142 data link control register 2 dlcr2 0xn143 transmit data link byte count register 2 tdlbcr2 0xn144 receive data link byte count register 2 rdlbcr2 0xn145 loopback code control register - code 3 lccr3 0xn146 receive loopback activation code register - code 3 rlacr3 0xn147 receive loopback deactivation code register - code 3 rldcr3 0xn148 loopback code control register - code 4 lccr4 0xn149 receive loopback activation code register - code 4 rlacr4 0xn14a receive loopback deactivation code register - code 4 rldcr4 0xn14b loopback code control register - code 5 lccr5 0xn14c receive loopback activation code register - code 5 rlacr5 0xn14d receive loopback deactivation code register - code 5 rldcr5 0xn14e loopback code control register - code 6 lccr6 0xn14f receive loopback activation code register - code 6 rlacr6 0xn150 receive loopback deactivation code register - code 6 rldcr6 0xn151 data link control register 3 dlcr3 0xn153 t able 1: r egister s ummary f unction s ymbol h ex
xrt86vx38 6 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description transmit data link byte count register 3 tdlbcr3 0xn154 receive data link byte count register 3 rdlbcr3 0xn155 loopback code control register - code 7 lccr7 0xn156 receive loopback activation code register - code 7 rlacr7 0xn157 receive loopback deactivation code register - code 7 rldcr7 0xn158 bert control register bcr 0xn163 ssm boc control register boccr 0xn170 ssm receive fdl register rfdlr 0xn171 ssm receive fdl match 1 register rfdlmr1 0xn172 ssm receive fdl match 2 register rfdlmr2 0xn173 ssm receive fdl match 3 register rfdlmr3 0xn174 ssm transmit fdl register tfdlr 0xn175 ssm transmit byte count register tbcr 0xn176 receive ds-0 monitor registers rds0mr 0xn15f - 0xn1cf transmit ds-0 monitor registers tds0mr 0xn1d0 - 0xn1ef device id register devid 0xn1fe revision number register revid 0xn1ff time slot (payload) control (0xn300 - 0xn3ff) transmit channel control register 0-23 tccr 0-23 0xn300 - 0xn317 transmit user code register 0-23 tucr 0-23 0xn320 - 0xn337 transmit signaling control register 0-23 tscr 0-23 0xn340 - 0xn357 receive channel control register 0-23 rccr 0-23 0xn360 - 0xn377 receive user code register 0-23 rucr 0-23 0xn380 - 0xn397 receive signaling control register 0-23 rscr 0-23 0xn3a0 - 0xn3b7 receive substitution signaling register 0-23 rssr 0-23 0xn3c0 - 0xn3d7 receive signaling array (0xn500 - 0xn51f) receive signaling array register 0 rsar0-23 0xn500 - 0xn517 lapdn buffer 0 lapd buffer 0 control register lapdbcr0 0xn600 - 0xn660 lapdn buffer 1 lapd buffer 1 control register lapdbcr1 0xn700 - 0xn760 t able 1: r egister s ummary f unction s ymbol h ex
xrt86vx38 7 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 performance monitor receive line code violation counter: msb rlcvcu 0xn900 receive line code violation counter: lsb rlcvcl 0xn901 receive frame alignment error counter: msb rfaecu 0xn902 receive frame alignment error counter: lsb rfaecl 0xn903 receive severely errored frame counter rsefc 0xn904 receive synchronization bit (crc-6) error counter: msb rsbbecu 0xn905 receive synchronization bit (crc-6) error counter: lsb rsbbecl 0xn906 reserved - e1 mode only 0xn907 - 0xn908 receive slip counter rsc 0xn909 receive loss of frame counter rlfc 0xn90a receive change of frame alignment counter rcoac 0xn90b lapd frame check sequence error counter 1 lfcsec1 0xn90c prbs bit error counter: msb pbecu 0xn90d prbs bit error counter: lsb pbecl 0xn90e transmit slip counter tsc 0xn90f excessive zero violation counter: msb ezvcu 0xn910 excessive zero violation counter: lsb ezvcl 0xn911 lapd frame check sequence error counter 2 lfcsec2 0xn91c lapd frame check sequence error counter 3 lfcsec3 0xn92c interrupt generation/enable register address map (0xnb00 - 0xnb41) block interrupt status register bisr 0xnb00 block interrupt enable register bier 0xnb01 alarm & error interrupt status register aeisr 0xnb02 alarm & error interrupt enable register aeier 0xnb03 framer interrupt status register fisr 0xnb04 framer interrupt enable register fier 0xnb05 data link status register 1 dlsr1 0xnb06 data link interrupt enable register 1 dlier1 0xnb07 slip buffer interrupt status register sbisr 0xnb08 slip buffer interrupt enable register sbier 0xnb09 receive loopback code 0 interrupt and status register rlcisr0 0xnb0a receive loopback code 0 interrupt enable register rlcier0 0xnb0b t able 1: r egister s ummary f unction s ymbol h ex
xrt86vx38 8 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description reserved - e1 mode only - 0xnb0c - 0xnb0d excessive zero status register exzsr 0xnb0e excessive zero enable register exzer 0xnb0f ss7 status register for lapd 1 ss7sr1 0xnb10 ss7 enable register for lapd 1 ss7er1 0xnb11 rxlos/crc interrupt status register rlcisr 0xnb12 rxlos/crc interrupt enable register rlcier 0xnb13 receive loopback code 1 interrupt and status register rlcisr1 0xnb14 receive loopback code 1 interrupt enable register rlcier1 0xnb15 data link status register 2 dlsr2 0xnb16 data link interrupt enable register 2 dlier2 0xnb17 ss7 status register for lapd 2 ss7sr2 0xnb18 ss7 enable register for lapd 2 ss7er2 0xnb19 receive loopback code 2 interrupt and status register rlcisr2 0xnb1a receive loopback code 2 interrupt enable register rlcier2 0xnb1b receive loopback code 3 interrupt and status register rlcisr3 0xnb1c receive loopback code 3 interrupt enable register rlcier3 0xnb1d receive loopback code 4 interrupt and status register rlcisr4 0xnb1e receive loopback code 4interrupt enable register rlcier4 0xnb1f receive loopback code 5 interrupt and status register rlcisr5 0xnb20 receive loopback code 5 interrupt enable register rlcier5 0xnb21 receive loopback code 6 interrupt and status register rlcisr6 0xnb22 receive loopback code 6 interrupt enable register rlcier6 0xnb23 receive loopback code 7 interrupt and status register rlcisr7 0xnb24 receive loopback code 7 interrupt enable register rlcier7 0xnb25 data link status register 3 dlsr3 0xnb26 data link interrupt enable register 3 dlier3 0xnb27 ss7 status register for lapd 3 ss7sr3 0xnb28 ss7 enable register for lapd 3 ss7er3 0xnb29 customer installation alarm status register ciasr 0xnb40 customer installation alarm interrupt enable register ciaier 0xnb41 boc interrupt status register bocisr 0xnb70 boc interrupt enable register bocier 0xnb71 t able 1: r egister s ummary f unction s ymbol h ex
xrt86vx38 9 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 reserved - 0xnb72 - 0xnb73 boc unstable interrupt status register bocusr 0xnb74 boc unstable interrupt enable register bocuer 0xnb75 liu register summary - channel control registers liu channel control register 0 liuccr0 0x0fn0 liu channel control register 1 liuccr1 0x0fn1 liu channel control register 2 liuccr2 0x0fn2 liu channel control register 3 liuccr3 0x0fn3 liu channel control interrupt enable register liuccier 0x0fn4 liu channel control status register liuccsr 0x0fn5 liu channel control interrupt status register liuccisr 0x0fn6 liu channel control cable loss register liuccccr 0x0fn7 liu channel control arbitrary register 1 liuccar1 0x0fn8 liu channel control arbitrary register 2 liuccar2 0x0fn9 liu channel control arbitrary register 3 liuccar3 0x0fna liu channel control arbitrary register 4 liuccar4 0x0fnb liu channel control arbitrary register 5 liuccar5 0x0fnc liu channel control arbitrary register 6 liuccar6 0x0fnd liu channel control arbitrary register 7 liuccar7 0x0fne liu channel control arbitrary register 8 liuccar8 0x0fnf reserved - 0x0f80 - 0x0fdf liu register summary - global control registers liu global control register 0 liugcr0 0x0fe0 liu global control register 1 liugcr1 0x0fe1 liu global control register 2 liugcr2 0x0fe2 liu global control register 3 liugcr3 0x0fe4 liu global control register 4 liugcr4 0x0fe9 liu global control register 5 liugcr5 0x0fea reserved - 0x0feb - 0x0fff t able 1: r egister s ummary f unction s ymbol h ex
xrt86vx38 10 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description 1.0 register descriptions - t1 mode all address on this register description is shown in hex format t able 2: c lock s elect r egister (csr) h ex a ddress : 0 x n100 b it f unction t ype d efault d escription -o peration 7 lcv insert r/w 0 line code violation insertion this bit is used to force a line code violation (lcv) on the transmit output of ttip/tring. a ?0? to ?1? transition on this bit will cause a single lcv to be inserted on the transmit output of ttip/tring. 6 set t1 mode r/w 0 t1 mode select this bit is used to program the individual channel to operate in either t1 or e1 mode. 0 = configures the selected channel to operate in e1 mode. 1 = configures the selected ch annel to operate in t1 mode. 5 sync all transmit - ters to 8khz r/w 0 sync all transmit framers to 8khz this bit permits the user to configure the transmit t1 framer block to synchronize its ?transmit output? fr ame alignment with the 8khz signal that is derived from the mclk pll, as described below. 0 - disables the ?sync all transmit framers to 8khz? feature. 1 - enables the ?sync all transmit framers to 8khz? feature. n ote : this bit is only active if the mclk pll is used as the ?timing source? for the transmit t1 fram er? blocks. css[1:0] of this register allows users to select the transmit source of the framer. 4 clock loss detect r/w 1 clock loss detect enable/disable select this bit enables a clock loss protection feature for the framer when - ever the recovered line clock is used as the timing source for the trans - mit section. if the liu loses clock recovery, the clock distribution block will detect this occurrence and automatically begin to use the internal clock derived from mclk pll as the transmit source, until the liu is able to regain clock recovery. 0 = disables the clock loss protection feature. 1 = enables the clock loss protection feature. n ote : this bit needs to be enabled in order to detect the clock closs detection interrupt status (address: 0xnb00, bit 5) 3:2 reserved r/w 00 reserved
xrt86vx38 11 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 1:0 css[1:0] r/w 01 clock source select these bits select the timing source for the transmit t1 framer block. these bits can also determine the direction of txserclk, txsync, and txmsync in base rate operation mode (1.544mhz clock mode). in base rate (1.544mhz clock mode): t able 2: c lock s elect r egister (csr) h ex a ddress : 0 x n100 b it f unction t ype d efault d escription -o peration n ote : txsync/txmsync can be programmed as input or output depending on the setting of sync inv bit in register address 0xn109, bit 4. please see register description for the synchronization mux register (smr - 0xn109) table 8. n otes : in high-speed or multiplex ed modes, txserclk, txsync, and txmsync are all configured as inputs only. css[1:0] t ransmit s ource for the t ransmit t1 f ramer b lock d irection of t x serclk 00/11 loop timing mode the recovered line clock is cho- sen as the timing source. output 01 external ti ming mode the transmit serial input clock from the txserclk_n input pin is chosen as the timing source. input 10 internal ti ming mode the mclk pll is chosen as the timing source. output
xrt86vx38 12 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 3: l ine i nterface c ontrol r egister (licr) h ex a ddress : 0 x n101 b it f unction t ype d efault d escription -o peration 7 force_los r/w 0 force transmit los (to the line side) this bit permits the user to configure the transmit direction circuitry (within the channel) to transmit the los pattern to the remote terminal equipment, as described below. 0 - configures the transmit direction circuitry to transmit ?normal? traffic. 1 - configures the transmit direction circuitry to transmit the los pattern. 6 reserved r/w 0 single rail mode this bit can only be set if the liu block is also set to single rail mode. see register 0xnfe0, bit 7. 0 - dual rail 1 - single rail 5:4 lb[1:0] r/w 00 framer loopback selection these bits are used to select any of the following loop-back modes for the framer section. for liu loopba ck modes, see the liu configuration registers. 3:2 reserved r/w 0 reserved lb[1:0] t ypes o f l oop b ack s elected 00 normal mode (no loopback) 01 framer local loopback: when framer local loopback is enabled, the transmit pcm input data is looped back to the receive pcm out- put data. the receive inpu t data at rtip/rring is ignored while an all ones signal is transmitted out to the line interface. 10 framer far-end (remote) line loopback: when framer remote loopback is enabled, the digital data enters the framer inte rface, however does not enter the framing blocks. th e receive digital data from the liu is allowed to pass through the liu decoder/ encoder circuitry before returning to the line interface. 11 framer payload loopback: when framer payload loopback is enabled, the raw data within the receive time slots are looped back to the transmit framer block where the data is re-framed according to the transmit timing.
xrt86vx38 13 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 1 encode b8zs r/w 0 encode ami or b8zs/hdb3 line code select this bit enables or disables the b8zs/hdb3 encoder on the transmit path. 0 = enables the b8zs encoder. 1 = disables the b8zs encoder. n ote : when b8zs encoder is disabled, ami line code is used. 0 decode ami/b8zs r/w 0 decode ami or b8zs/hdb3 line code select this bit enables or disables the b8zs/hdb3 decoder on the receive path. 0 = enables the b8zs decoder. 1 = disables the b8zs decoder. n ote : when b8zs decoder is disabled, ami line code is received. t able 3: l ine i nterface c ontrol r egister (licr) h ex a ddress : 0 x n101 b it f unction t ype d efault d escription -o peration
xrt86vx38 14 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 4: f raming s elect r egister (fsr) h ex a ddress : 0 x n107 b it f unction t ype d efault d escription -o peration 7 signaling update on superframe boundaries r/w 0 enable robbed-bit signaling update on superframe boundary on both transmit and receive direction this bit enables or disables robbed-bit signaling update on the superframe boundary for both the tr ansmit and receive side of the framer. on the receive side: if signaling update is enabled, signaling data on the receive side (rxsig pin and signaling array register - rsar) will be updated on the superframe boundary, otherwise, signaling data will be updated as soon as it is received. on the transmit side: if signaling update is enabled, any signaling data changes on the transmit side will be transmitted on the superframe boundary, other - wise, signaling data will be transmitted as soon as it is changed. 0 - disables the signaling update f eature for both transmit and receive. 1 - enables the signaling update feature for both transmit and receive. 6 force crc errors r/w 0 force crc errors (to the line side) this bit permits the user to force the transmit t1 framer block to transmit crc errors within the outbo und t1 data-stream, as depicted below. 0 - disables crc error transmission on the outbound t1 stream. 1 - enables crc error transmission on the outbound t1 stream. 5 j1_mode r/w 0 j1 mode this bit is used to configure the device in j1 mode. once the device is configured in j1 mode, the following two changes will happen: 1. crc calculation is done in j1 format. the j1 crc6 calcula - tion is based on the actual values of all 4632 bits in a t1 multi - frame including fe bits instead of assuming all fe bits to be a one in t1 format. 2. receive and transmit yellow alarm signal format is inter - preted per the j1 standard. (j1-sf or j1-esf) 0 - configures the device in t1 mode. (default) 1 - configures the device in j1 mode. n ote : users can select between j1-sf or j1-esf by setting this bit and the t1 framing mode select bits[2:0] (bits 2-0 within this register). 4 oneonly r/w 0 allow only one sync candidate this bit is used to specify one of t he synchronization criteria that the receive t1 framer block employs. 0 - allows the receive t1 framer to select any one of the winners in the matching process when there are two or more valid synchroniza - tion patterns appear in the required time frame. 1 - allows the receive t1 framer to declare success of match when there is only one candidate left in the required time frame.
xrt86vx38 15 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 3 fastsync r/w 0 faster sync algorithm this bit is used to specify one of t he synchronization criteria that the receive t1 framer block employs. if this ?faster sync algorithm? is enabled, the receive t1 framer block will declare synchronization earlier. the table below specifies the number of co nsecutive frames with correct f-bits that the t1 re ceive framer must receive in order to declare ?sync? when fastsync is enabled or disabled. 0 - disables fastsync feature. 1 - enables fastsync feature. 2-0 fsl[2:0] r/w 000 t1 framing mode select [2:0] these three bits permit the user to select the exact t1 framing format that the channel is to operate in. bit 2 is msb and bit 0 is lsb. the following table shows the five dif - ferent framing formats that can be selected by configuring these three bits accordingly. n ote : changing framing formats 'on the fly' will cause the receive t1 framer block to undergo a ?reframe? event. t able 4: f raming s elect r egister (fsr) h ex a ddress : 0 x n107 b it f unction t ype d efault d escription -o peration framing fastsync = 0 fastsync = 1 esf 96 48 sf 48 24 n 48 24 slc ? 96 48 24 framing fs[2] fs[1] fs[0] esf 0 x x sf 1 0 1 n 1 1 0 t1dm 1 1 1 slc ? 96 1 0 0
xrt86vx38 16 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 5: a larm g eneration r egister (agr) h ex a ddress : 0 x n108 b it f unction t ype d efault d escription -o peration 7 yellow alarm - one second rule r/w 0 one-second yellow alarm rule enforcement this bit is used to enforce the one-second yellow alarm rule according to the yel - low alarm (rai) transmission duration per the ansi standards. if the one second alarm rule is enforced, the following will happen: 1. rai will be transmitted for at least one second for both esf and sf. 2. there must be a minimum of one second delay between termination of the first rai and the initiation of a subsequent rai. 3. alarm_enb bit (see description of bi t 6 of this register) controls the duration of rai. 4. yel[0] & yel[1] (see description of bits 5-4 of this register) controls the format of rai. if the one second alarm rule is not enforced, the following will happen: 1. rai will be transmitted for at least one second for esf and sf. 2. minimum one second delay between termination of the first rai and the initiation of the subsequent rai is not enforced. 3. yel[0] and yel[1] bits (see description of bits 5-4 of this register) are used to control the duration and th e format of rai transmission. 0 - the one-second yellow alarm rule is not enforced. 1 - the one-second yellow alarm rule is enforced. n ote : when setting this bit to ?0?, yellow alarm transmission will be backward compatible with the xrt86l38 device. xrt86l38 does not support the one-second yellow alarm rule. 6 alarm_enb r/w 0 yellow alarm transmission enable this bit is used to control the duration of yellow alarm (rai) when the one-second yellow alarm rule is enforced (bit 7 of this register set to?1?). when the one-second yellow alarm rule is not enforced (bit 7 of this register set to?0?), the duration of the rai is controlled by the yel[0] and yel[1] bits (bits 5-4 of this register). if the one-second alarm rule is enforced: 0 - stop the transmission of yellow alarm (see description of bits 5-4). 1 - start the transmission of yellow alarm (see description of bits 5-4). n ote : this bit has no function if the one second alarm rule is not enforced.
xrt86vx38 17 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 5-4 yel[1:0] r/w 00 yellow alarm (rai) duration and format the exact function of these bits depends on whether or not the one-second yellow alarm rule is enforced. (bit 7 of this register). the decoding of these bits are explained in table 6 and table 7 below . t able 5: a larm g eneration r egister (agr) h ex a ddress : 0 x n108 b it f unction t ype d efault d escription -o peration t able 6: yellow alarm duration and format when one second rule is not enforced yel[1:0] y ellow a larm d uration and f ormat 00 disable the transmission of yellow alarm 01 sf or n mode: rai is transmitted as bit 2 = 0 (second msb) in all ds0 data chan- nel. t1dm mode: rai is transmitted as y-bit = 0 (6th bit in the sync byte). esf mode: 1. if yel[0] bit is set ?high? for a duration shorter or equal to the time required to transmit 255 patterns of 1111_1111_0000_0000 on the 4-kbit/s data link bits (m1- m12), rai is transmitted for 255 patterns.of 1111_1111_0000_0000 (approximately 1 second) 2. if yel[0] bit is set ?high? for a duration longer than the time required to transmit 255 patterns of 1111_1111_00 00_0000 on the 4-kbit/s data link bits (m1-m12), rai transmission continues until yel[0] bit is set ?low?. 3. if yel[0] bit forms another pulse during the rai transmission, it resets the pattern counter and extends the rai duration for another 255 patterns of 1111_1111_0000_0000. (approximately 1 second) 10 sf mode: rai is transmitted as a ?1? in the fs bit of frame 12 (this is rai for j1 sf standard). t1dm mode : ? rai is transmitted as y-bit = 0 (6th bit in the sync byte). esf mode : rai is controlled by the duration of yel[1] bit. this allows continu- ous rai of any length. 11 sf, n, and t1dm mode: rai format is the same as descri bed above when yel[1:0] is set to?01?. esf mode: rai duration is the same as described above when yel[1:0] is set to?01?, except that format of rai is transmitted as 255 patterns of 1111_1111_1111_1111 (sixteen ones) on the 4kbits/s data link bits instead of 255 patterns of 1111_1111_0000_0000. n ote : 255 patterns of 1111_1111_1111_111 is the j1 esf rai standard)
xrt86vx38 18 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description 5-4 yel[1:0] r/w 00 ( continued) t able 5: a larm g eneration r egister (agr) h ex a ddress : 0 x n108 b it f unction t ype d efault d escription -o peration t able 7: yellow alarm format when one second rule is enforced yel[1:0] y ellow a larm f ormat 00 disable the transmission of yellow alarm 01 sf or n mode : rai is transmitted as bit 2 = 0 (second msb) in all ds0 data channel. t1dm mode: rai is transmitted as y-bit = 0 (6th bit in the sync byte). esf mode: yel[1:0] controls the format of rai. when yel[1:0] is set to?01?, rai is transmitted as 255 patterns of 1111_1111_0000_0000 on the 4- kbit/s data link (m1-m12) (approximately 1 second). alarm_enb (bit 6 of this registe r) controls the duration of rai as described below: 1. if alarm_enb bit is set ?high? for a duration shorter or equal to the time required to transmit 255 pattern of 1111_1111_0000_0000 on the 4-kbit/s data link (m1-m12), rai is transmitted for 255 patterns. (approximately 1 second) 2. if alarm_enb bit is set ?high? for a duration longer than the time required to transmit 255 patterns of 1111_1111_0000_0000 on the 4-kbit/s data link (m1-m12), rai continues until alarm_ enb bit is set ?low?. 3. if alarm_enb forms another pulse during an alarm transmission, it resets the pattern counter and extends the rai duration for another 255 patterns.(approximately 1 second) n ote : a minimum of one second delay between termination of the first rai and the initiation of a subsequent rai is enforced. 10 sf mode: rai is transmitted as a ?1? in the fs bit of frame 12 (this is rai for j1 sf standard). t1dm mode : ? rai is transmitted as y-bit = 0 (6th bit in the sync byte). esf mode : rai is controlled by the duration of alarm_enb bit. this allows continuous rai of any length. 11 sf, n, and t1dm mode: rai format is the same as described above when yel[1:0] is set to?01?. esf mode: rai duration is the same as described above when yel[1:0] is set to?01?, except that format of rai is transmitted as 255 patterns of 1111_1111_1111_1111 on the 4kbits/s data link bits (j1 esf stan- dard) instead of 255 patterns of 1111_1111_00 00_0000.
xrt86vx38 19 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 3-2 transmit ais pattern select[1:0] r/w 00 transmit ais pattern select[1:0]: these two bits permit the user to do the following. 1. to select the appropriate ais pattern that the tran smit t1 framer block will transmit to the remote terminal equipment, and 2. to command (via software control) th e transmit t1 framer block to transmit that particular ais pattern to the remote terminal equipment, as depicted below. n ote : for normal operation (e.g., to configure the transmit t1 framer block to transmit normal t1 traffic) the user should set this bit to ?[x, 0]? 1-0 ais defect declaration criteria [1:0] r/w 00 ais defect declaration criteria[1:0]: these bits permit the user to specify the types of ais patterns that the receive t1 framer block must detect before it will declare the ais defect condition. t able 5: a larm g eneration r egister (agr) h ex a ddress : 0 x n108 b it f unction t ype d efault d escription -o peration aisg[1:0] t ypes of ais p atterns t ransmitted 00/10 disable ais alarm generation the transmit t1 framer blo ck will transmit ?normal? t1 traffic to the remote terminal equipment. 01 enable unframed ais alarm generation transmit t1 framer block will transmit an unframed all ones pattern, as an ais pattern. 11 enable framed ais alarm generation transmit t1 framer block will transmit a framed, all ones pattern, as the ais pattern. aisd[1:0] ais defect declaration criteria 00/10 ais detection disabled ais defect condition will not be declared. 01 enable unframed and framed ais alarm detection receivet1 framer block will detect both unframed and framed ais pattern 11 enable framed ais alarm detection receive t1 framer block will detect only framed ais pat- tern
xrt86vx38 20 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 8: s ynchronization mux r egister (smr) h ex a ddress : 0 x n109 b it f unction t ype d efault d escription -o peration 7 reserved - - reserved 6 mframealign r/w 0 transmit multiframe sync alignment this bit forces transmit t1 framer block to align with the backplane multiframe bounda ry (txmsync_n). 0 = do not force the transmit t1 framer block to align with the txm - sync signal. 1 = force the transmit t1 framer block to align with the txmsync signal. n ote : this bit is not used in base rate (1.544mhz clock) mode. 5 msync r/w o transmit super frame boundary this bit provides an option to use the transmit single frame boundary (txsync) as the transmit multi-frame boundary (txmsync) in high speed or multiplexed modes. in 1. 544mhz clock mode (base rate), the txmsync is used as the tran smit superframe boundary, in other clock modes (i.e. high speed or multiplexed modes), txmsync is used as an input transmit clock for the backplane interface. 0 = configures the txsync as a single frame boundary. 1 = configures the txsync as a superframe boundary (txmsync) in high-speed or multiplexed mode. n ote : this bit is not used in base rate (1.544mhz clock) mode.
xrt86vx38 21 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 4 transmit frame sync select r/w 0 transmit frame sync select this bit permits the user to configure the system-side terminal equipment or the t1 transmit framer to dictate whenever the trans - mit t1 framer block will initiate it s generation and transmission of the very next t1 frame. if the system si de controls, then all of the follow - ing will be true. 1. the corresponding txsync_n and txmsync_n pins will function as input pins. 2. the transmit t1 framer block will initiate its generation of a new t1 frame whenever it samples the corresponding ?txsync_n? input pin ?high? (via the txserclk_n input clock signal). 3. the transmit t1 framer block will initiate its generation of a new multiframe whenever it samples the corresponding ?txmsync_n? input pin ?high?. this bit can also be used to select the direction of the transmit single frame boundary (txsync) and mu lti-frame boundary (txmsync) depending on whether txserclk is chosen as the timing source for the transmit section of the framer. (c ss[1:0] = 01 in register 0xn100) if txserclk is chosen as the timing source: 0 = configures txsync and txmsync as inputs. (system side controls) 1 = configures txsync and txm sync as outputs. (chip controls) if either recovered line clock, mclk pll is chosen as the tim - ing source: 0 = configures txsync and txm sync as outputs. (chip controls) 1 = configures txsync and txmsync as inputs. (system side controls) n ote : txserclk is chosen as the tran smit clock if css[1:0] of the clock select register (register address: 0xn100) is set to b01. recovered clock is chosen as the transmit clock if css[1:0] is set to b00 or b11; internal clock is chosen as the transmit clock if css[1:0] is set to b10. 3 - 2 reserved - - reserved t able 8: s ynchronization mux r egister (smr) h ex a ddress : 0 x n109 b it f unction t ype d efault d escription -o peration
xrt86vx38 22 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description 1 crc-6 bits source select r/w 0 crc-6 bits source select this bit permits the user to specify the source of the crc-6 bits, within the outbound t1 data-stream, as depicted below. 0 - configures the transmit t1 framer block to internally compute and insert the crc-6 bits within the outbound t1 data-stream. 1 - configures the transmit t1 framer block to externally accept data from the txser_n input pin, a nd to insert this data into the crc- 6 bits within the outbound t1 data-stream. this bit is ignored if crc multiframe alignment is disabled 0 framing bits source select r/w 0 framing bits source select this bit is used to specify the source for the framing bits that will be inserted into the outbound t1 frames. the framing bits can be gen - erated internally or inserted from the transmit serial input pin. (txser_n input pin) 0 = configures the transmit t1 framer block to internally generate and insert the framing bits into the outbound t1 data stream. 1 = configures the transmit t1 framer block to externally accept framing bits from the txser_n input pi n, and to insert this data to the outbound t1 data-stream. t able 8: s ynchronization mux r egister (smr) h ex a ddress : 0 x n109 b it f unction t ype d efault d escription -o peration
xrt86vx38 23 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 9: t ransmit s ignaling and d ata l ink s elect r egister (tsdlsr) h ex a ddress :0 x n10a b it f unction t ype d efault d escription -o peration 7 reserved - - reserved 6 reserved - - reserved 5-4 txdlbw[1:0] r/w 00 transmit data link bandwidth[1:0] these two bits are used to select the bandwidth for data link mes - sage transmission. data link messages can be transmitted at a 4khz rate or at a 2khz rate on odd or even framing bits depending on the configuration of th ese three bits. the table below specifies the four different configurations. n ote : this bit only applies to t1 esf framing format. for slc96 and n framing formats, fdl is a 4khz data link channel. for t1dm, fdl is a 8khz data link channel. 3-2 txde[1:0] r/w 00 transmit d/e timeslot source select[1:0]: these two bits specify the source for transmit d/e time slots. the table below shows the different sources from which d/e time slots can be inserted . t x dlbw[1:0] t ransmit d ata l ink b andwidth s elected 00 data link bits are inserted in every frame. facility data link bits (fdl) is a 4khz data link channel. 01 data link bits are inserted in every other frame. facility data link bits (fdl) is a 2khz data link channel carried by odd framing bits (frames 1,5,9.....) 10 data link bits are inserted in every other frame. facility data link bits (fdl) is a 2khz data link channel carried by even framing bits (frames 3,7,11.....) 11 reserved t x de[1:0] s ource for t ransmit d/e t imeslots 00 txser_n input pin - the d/e time slots are inserted from the transmit serial data input pin (txser_n) pin. 01 transmit lapd controller - the d/e time slots are inserted from lapd controller. 10 reserved 11 txfrtd_n - the d/e time slots are inserted from the transmit fractional input pin.
xrt86vx38 24 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description 1-0 txdl[1:0] r/w 00 transmit data link source select [1:0] these two bits specify the source for data link bits that will be inserted in the outbound t1 frames. the table below shows the three different sources from which data link bits can be inserted . t able 9: t ransmit s ignaling and d ata l ink s elect r egister (tsdlsr) h ex a ddress :0 x n10a b it f unction t ype d efault d escription -o peration t x dl[1:0] s ource for d ata l ink b its 00 transmit lapd controller #1 / slc96 buffer - the data link bits are inserted from the transmit lapd controller #1 or slc96 buffer. n ote : lapd controller #1 is the only lapd controller that can be used to transport lapd messages through the data link bits 01 txser_n input pin - the data link bits are inserted from the transmit serial data input pin (txser_n) pin. 10 txoh_n input pin - the data link bits are inserted from the transmit overhead input pin. (txoh_n) 11 data link bits are forced to 1.
xrt86vx38 25 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 10: f raming c ontrol r egister (fcr) h ex a ddress : 0 x n10b b it f unction t ype d efault d escription -o peration 7 reframe r/w 0 force reframe a ?0? to ?1? transition will force the receive t1 framer to restart the syn - chronization process. this bit field is automatically cleared (set to 0) after frame synchronization is reached. 6 framing with crc checking r/w 1 framing with crc checking in esf this bit permits the user to inclu de crc verification as a part of the ?t1/esf framing alignment? process. if the user enables this feature, then the receive t1 framer block wil l also check and verify that the incoming t1 data-stream contains correct crc data, prior to declaring the ?in-frame? condition. 0 - crc verification is not included in the ?framing alignment? pro - cess. 1 - receive t1 framer block will also check for correct crc values prior to declaring the ?in-frame? condition. 5-3 lof tolerance[2:0] r/w 000 lof defect declaration tolerance[2:0]: these bits along with the lof_range[ 2:0] bits are used to define the lof defect declaration criteria. the receive t1 framer block will declare the lof defect condition anytime it detects ?lof_tolerance[2:0]? out of ?lof_ran ge[2:0] framing bit errors within the incoming t1 data-stream. the recommended lof_tolr value is 2. n ote : a ?0? value for lof_tolr is internally blocked. a lof_tolr value must be specified. 2-0 lof_range[2:0] r/w 011 lof defect declaration range[2:0]: these bits along with the ?lof_toler ance[2:0] bits are used to define the ?lof defect declaration? criteria. the receive t1 framer block will declare the lof defect condition anytime it has received ?lof_tolerance[2:0] out of ?lof_ra nge[2:0] framing bit errors, within the incoming t1 data-stream. the recommended lof_ang value is 5. n ote : a ?0? value for lof_rang is internally blocked. a lof_rang value must be specified.
xrt86vx38 26 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 11: r eceive s ignaling & d ata l ink s elect r egister (rsdlsr) h ex a ddress : 0 x n10c b it f unction t ype d efault d escription -o peration 7 reserved - - reserved 6 reserved - - reserved 5-4 rxdlbw[1:0] r/w 00 receive data link bandwidth[1:0]: these two bits select the bandwidth for data link message reception. data link messages can be received at a 4khz rate or at a 2khz rate on odd or even framing bits dependi ng on the configuration of these bits. the table below specifies the different configurations. n ote : this bit only applies to t1 esf framing format. for slc96 and n framing formats, fdl is a 4khz data link channel. for t1dm, fdl is a 8khz data link channel. 3-2 rxde[1:0] r/w 00 receive d/e time-slot destination select[1:0]: these bits permit the user to specify the ?destination? circuitry that will receive and process the d/e-time-s lot within the incoming t1 data- stream. r x dlbw[1:0] r eceive d ata l ink b andwidth s elected 00 received data link bits are extracted in every frame. facility data link bits (fdl) is a 4khz data link channel. 01 received data link bits are extracted in every other frame. facility data link bits (fdl) is a 2khz data link channel carried by odd framing bits (frames 1,5,9.....) 10 received data link bits are extracted in every other frame. facility data link bits (fdl) is a 2khz data link channel carried by even framing bits (frames 3,7,11.....) 11 reserved r x de[1:0] d estination c ircuitry for r eceive d/e t ime -s lot 00 rxser_n output pin - the d/e time slots are out- put to the receive serial data output pin (rxser_n) pin. 01 receive lapd controller block - the d/e time slots are output to receive lapd controller block. 10 reserved 11 rxfrtd_n output pin - the d/e time slots are output to the receive fractional output pin.
xrt86vx38 27 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 1-0 rxdl[1:0] r/w 00 receive data-link destination select[1:0]: these bits specify the destination circ uitry, that is used to process the data-link data, within the incoming t1 data-stream. t able 11: r eceive s ignaling & d ata l ink s elect r egister (rsdlsr) h ex a ddress : 0 x n10c b it f unction t ype d efault d escription -o peration r x dl[1:0] d estination c ircuitry for r eceive d ata -l ink 00 receive lapd controller block # 1 and rxser_n - the data link bits are routed to the receive lapd controller block #1 and the rxser_n output pin n ote : lapd controller #1 is the only lapd controller that can be used to extract lapd messages through the data link bits 01 rxser_n - the data link bits are routed to the rxser_n output pin. 10 rxoh_n and rxser_n - the data link bits are routed to the rxoh_n and rxser_n output pins. 11 data link bits are forced to 1 .
xrt86vx38 28 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 12: r eceive s ignaling c hange r egister 0 (rscr 0) h ex a ddress : 0 x n10d b it f unction t ype d efault d escription -o peration 7 ch. 0 rur 0 these bits indicate whether the channel associated signaling data, associated with time-slots 0 through 7 within the incoming t1 data- stream, has changed since the last re ad of this register, as depicted below. 0 - cas data (for time-slots 0 through 7) has not changed since the last read of this register. 1 - cas data (for time-slots 0 through 7) has changed since the last read of this register. n otes : this register is only active if the incoming t1 data-stream is using channel associated signaling. 6 ch. 1 rur 0 5 ch.2 rur 0 4 ch.3 rur 0 3 ch.4 rur 0 2 ch.5 rur 0 1 ch.6 rur 0 0 ch.7 rur 0 t able 13: r eceive s ignaling c hange r egister 1 (rscr 1) h ex a ddress : 0 x n10e b it f unction t ype d efault d escription -o peration 7 ch.8 rur 0 these bits indicate whether the channel associated signaling data, associated with time-slots 8 through 15 within the incoming t1 data- stream, has changed since the last re ad of this register, as depicted below. 0 - cas data (for time-slots 8 th rough 15) has not changed since the last read of this register. 1 - cas data (for time-slots 8 through 15) has changed since the last read of this register. this register is only active if the incoming t1 data-stream is using channel associated signaling. 6 ch.9 rur 0 5 ch.10 rur 0 4 ch.11 rur 0 3 ch.12 rur 0 2 ch.13 rur 0 1 ch.14 rur 0 0 ch.15 rur 0 t able 14: r eceive s ignaling c hange r egister 2 (rscr 2) h ex a ddress : 0 x n10f b it f unction t ype d efault d escription -o peration 7 ch.16 rur 0 these bits indicate whether the channel associated signaling data, associ - ated with time-slots 16 through 23 within the incoming t1 data-stream, has changed since the last read of this register, as depicted below. 0 - cas data (for time-slots 16 through 23) has not changed since the last read of this register. 1 - cas data (for time-slots 16 through 23) has changed since the last read of this register. n ote : this register is only active if the incoming t1 data-stream is using channel associated signaling. 6 ch.17 rur 0 5 ch.18 rur 0 4 ch.19 rur 0 3 ch.20 rur 0 2 ch.21 rur 0 1 ch.22 rur 0 0 ch.23 rur 0
xrt86vx38 29 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 15: r eceive i n f rame r egister (rifr) h ex a ddress : 0 x n112 b it f unction t ype d efault d escription -o peration 7 in frame ro 0 in frame state this read-only bit indicates whether the receive t1 framer block is currently declaring the ?in-frame? condition with the incoming t1 data- stream. 0 - indicates that the receive t1 fr amer block is currently declaring the lof (loss of frame) defect condition. 1 - indicates that the receive t1 framer block is currently declaring itself to be in the ?in-frame? condition. 6 reserved - - reserved (for e1 mode only) 5 ais_ingress r/w 0 ais ingress generation this bit is used to send an ais signal (unframed all ones) on the receiver output rxser. 0 - disabled 1 - rx ais ingress generation enabled 4 fralarmmask r/w 0 framer alarm mask this bit can be used to mask the alarms associated with the framing mode that is selected. regardless of the framing mode, this bit will mask to following alarms: lof, if, cofa, comfa, fe, se, and fmd. by default, the alarms are not masked. 0 - disabled 1 - framing alarms masked 3 ds0yel r/w 0 ds-0 yellow alarm generation (t1 mode only) this bit is used to send a ds-0 yellow alarm to ttip/tring egress direc - tion regardless of what framing format is used if bit 2 in this register is set to "0". if bit 2 is set to "1", then the yellow alarm is sent to rxser on the ingress side. ds-0 yellow alarm is defined as bit 2 = 0 (second msb) in all ds-0 data channels. 0 - disabled 1 - ds-0 yellow alarm generation enabled 2 ds0yel_switch r/w 0 ds-0 yellow alarm switch bit (t1 mode only) this bit is used to set the direction of the ds-0 yellow alarm as described in bit 3 of this register. 0 - ds-0 yellow egress (ttip/tring) generation 1 - ds-0 yellow ingress (rxser) generation 1-0 reserved - - reserved (for e1 mode only)
xrt86vx38 30 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 16: d ata l ink c ontrol r egister (dlcr1) h ex a ddress : 0 x n113 b it f unction t ype d efault d escription -o peration 7 slc-96 data link enable r/w 0 slc?96 datalink enable this bit permits the user to configure the channel to support the transmission and reception of the ?slc-96 type? of data-link mes - sage. 0 - channel does not support the transmission and reception of ?slc-96? type of data-link messages. regular sf framing bits will be transmitted. 1 - channel supports the transmission and reception of the ?slc- 96? type of data-link messages. this bit is only active if the channel has been configured to operate in either the slc-96 or the esf framing formats. 6 mos abort disable r/w 0 mos abort disable: this bit permits the user to either enable or disable the ?automatic mos abort? feature within transmit hdlc controller # 1. if the user enables this feature, then transmit hdlc controller block # 1 will automatically transmit the ab ort sequence (e.g., a zero fol - lowed by a string of 7 consecutive ?1s?) whenever it abruptly transi - tions from transmitting a mos type of message, to transmitting a bos type of message. if the user disables this feature, then the transmit hdlc controller block # 1 will not transmit the abort sequence, whenever it abruptly transitions from transmi tting a mos-type of message to transmitting a bos-type of message. 0 - enables the ?automat ic mos abort? feature 1 - disables the ?automatic mos abort? feature 5 rx_fcs_dis r/w 0 receive frame check sequence (fcs) verification enable/dis - able this bit permits the user to configure the receive hdlc controller block # 1 to compute and verify the fcs value within each incoming lapd message frame. 0 - enables fcs verification 1 - disables fcs verification 4 autorx r/w 0 auto receive lapd message this bit configures the receive hdlc controller block #1 to discard any incoming bos or lapd message frame that exactly match which is currently stored in the receive hdlc1 buffer. 0 = disables this ?auto discard? feature 1 = enables this ?auto discard? feature. 3 tx_abort r/w 0 transmit abort this bit configures the transmit hdlc controller block #1 to trans - mit an abort sequence (string of 7 or more consecutive 1?s) to the remote terminal. 0 - configures the transmit hdlc controller block # 1 to function normally (e.g., not transmit the abort sequence). 1 - configures the transmit hdlc controller block # 1 to transmit the abort sequence.
xrt86vx38 31 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 2 tx_idle r/w 0 transmit idle (flag sequence byte) this bit configures the transmit hdlc controller block #1 to uncon - ditionally transmit a repeating string of flag sequence octets (0x7e) in the data link channel to the remote terminal. in normal condi - tions, the transmit hdlc controll er block will repeatedly transmit the flag sequence octet whenever there is no mos message to transmit to the remote terminal eq uipment. however, if the user invokes this ?transmit idle sequ ence? feature, th en the transmit hdlc controller block will unconditionally transmit a repeat - ing stream of the flag sequence octet (thereby overwriting all out - bound mos data-link messages). 0 - configures the transmit hdlc controller block # 1 to transmit data-link information in a ?normal? manner. 1 - configures the transmit hdlc controller block # 1 to transmit a repeating string of flag s equence octets (0x7e). n ote : this bit is ignored if the transmit hdlc1 controller is operating in the bos mode - bit 0 (mos/bos) within this register is set to 0. 1 tx_fcs_en r/w 0 transmit lapd message with frame check sequence (fcs) this bit permits the user to configure the transmit hdlc controller block # 1 to compute and append fcs octets to the ?back-end? of each outbound mos data-link message. 0 - configures the transmit hdlc controller block # 1 to not com - pute and append the fcs octets to the back-end of each outbound mos data-link message. 1 - configures the transmit hdlc controller block # 1 to com - pute and append the fcs octets to the back-end of each outbound mos data-link message. n ote : this bit is ignored if the tran smit hdlc1 controller has been configured to operate in the bos mode - bit 0 (mos/bos) within this register is set to 0. 0 mos/ bos r/w 0 message oriented signaling/bit oriented signaling send this bit permits the user to enable lapd transmission through hdlc controller block # 1 using either bos (bit-oriented signaling) or mos (message-oriented signaling) frames. 0 - transmit hdlc controller block # 1 bos message send. 1 - transmit hdlc controller block # 1 mos message send. n ote : this is not an enable bit. this bit must be set to "0" each time a bos is to be sent. t able 16: d ata l ink c ontrol r egister (dlcr1) h ex a ddress : 0 x n113 b it f unction t ype d efault d escription -o peration
xrt86vx38 32 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 17: t ransmit d ata l ink b yte c ount r egister (tdlbcr1) h ex a ddress : 0 x n114 b it f unction t ype d efault d escription -o peration 7 txhdlc1 bufavail/ bufsel r/w 0 transmit hdlc1 buffer available/buffer select this bit has different functions, depending upon whether the user is writing to or reading from this register, as depicted below. if the user is writing data into this register bit: 0 - configures the transmit hdlc1 controller to read out and trans - mit the data, residing within ?transmit hdlc1 buffer # 0", via the data link channel to the remote terminal equipment. 1 - configures the transmit hdlc1 controller to read out and trans - mit the data, residing within the ?transmit hdlc1 buffer #1?, via the data link channel to the remote terminal equipment. if the user is reading data from this register bit: 0 - indicates that ?transmit hdlc1 buffer # 0" is the next available buffer. in this case, if the user wishes to write in the contents of a new ?outbound? data link message into the transmit hdlc1 mes - sage buffer, he/she should proceed to write this message into ?transmit hdlc1 buffer # 0" - address location: 0xn600. 1 - indicates that ?transmit hdlc1 buffer # 1" is the next available buffer. in this case, if the user wishes to write in the contents of a new ?outbound? data link message into the transmit hdlc1 mes - sage buffer, he/she should proceed to write this message into ?transmit hdlc1 buffer # 1" - address location: 0xn700. n ote : if one of these transmit hdlc1 buffers contain a message which has yet to be completely read-in and processed for transmission by the transmit hdlc1 controller, then this bit will automatically reflect the value corresponding to the next available buffer when it is read. changing this bit to the in- use buffer is not permitted. 6-0 tdlbc[6:0] r/w 0000000 transmit hdlc1 message - byte count the exact function of these bits depends on whether the transmit hdlc 1 controller is configured to transmit mos or bos messages to the remote terminal equipment. in bos mode: these bit fields contain the number of repetitions the bos message must be transmitted before the transmit hdlc1 controller gener - ates the transmit end of transfer (txeot) interrupt and halts trans - mission. if these fields are set to 00000000, then the bos message will be transmitted for an indefinite number of times. in mos mode: these bit fields contain the length, in number of octets, of the mes - sage to be transmitted. the l ength of mos message specified in these bits include header bytes such as the sapi, tei, control field, however, it does not include the fcs bytes.
xrt86vx38 33 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 18: r eceive d ata l ink b yte c ount r egister (rdlbcr1) h ex a ddress : 0 x n115 b it f unction t ype d efault d escription -o peration 7 rbufptr r/w 0 receive hdlc1 buffer-pointer this bit identifies which receive hdlc1 buffer contains the most recently received hdlc1 message. 0 - indicates that receive hdlc1 buffer # 0 contains the contents of the most recently received hdlc message. 1 - indicates that receive hdlc1 buffer # 1 contains the contents of the most recently received hdlc message. 6-0 rdlbc[6:0] r/w 0000000 receive hdlc message - byte count the exact function of these bits depends on whether the receive hdlc controller block #1 is configured to receive mos or bos messages. in bos mode: these seven bits contain the num ber of repetitions the bos mes - sage must be received before the receive hdlc1 controller gener - ates the receive end of transfer (rxeot) interrupt. if these bits are set to ?0000000?, the message will be received indefinitely and no receive end of transfer (rxeot) interrupt will be generated. in mos mode: these seven bits contain the size in bytes of the hdlc1 message that has been received and writte n into the receive hdlc buffer. the length of mos message shown in these bits include header bytes such as the sapi, tei, control field, and the fcs bytes.
xrt86vx38 34 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 19: s lip b uffer c ontrol r egister (sbcr) h ex a ddress : 0 x n116 b it f unction t ype d efault d escription -o peration 7 txsb_isfifo r/w 0 transmit slip buffer mode this bit permits the user to configure t he transmit slip buffer to function as either ?slip-buffer? mode, or as a ?fifo?, as depicted below. 0 - configures the transmit slip buff er to function as a ?slip-buffer?. 1 - configures the transmit slip buffer to function as a ?fifo?. n ote : transmit slip buffer is only used in high-speed or multiplexed mode where txserclkn must be configured as inputs only. users must make sure that the ?transmit direction? timing (i.e. txmsync) and the txserclk input clock signal are synchronous to prevent any transmit slips from occuring. n ote : the data latency is dictated by fifo latency in the fifo latency register (register 0xn117). 6-5 reserved - - reserved 4 sb_forcesf r/w 0 force signaling freeze this bit permits the user to freeze any signaling update on the rxsign output pin as well as the receive signaling array register -rsar (0xn500- 0xn51f) until this bit is cleared. 0 = signaling on rxsig and rsar is updated immediately. 1 = signaling on rxsig and rsar is not updated until this bit is set to ?0?. 3 sb_sfenb r/w 0 signal freeze enable upon buffer slips this bit enables signaling freeze for one multiframe after the receive buffer slips. if signaling freeze is enabled, then the ?receive channel? will freeze all sig - naling updates on rxsig pin and rsar (0xn500-0xn51f) for at least ?one- multiframe? period, after a ?slip-event? has been detected within the ?receive slip buffer?. 0 = disables signaling freeze for one multi-frame after receive buffer slips. 1 = enables signaling freeze for one multi-frame after receive buffer slips. 2 sb_sdir r/w 1 slip buffer (rxsync) direction select this bit permits user to select the direction of the receive frame boundary (rxsync) signal if the receive buffer is enabled. (i.e. sb_enb[1:0] = 01 or 10). if slip buffer is bypassed, rx sync is always an output pin. 0 = selects the rxsync signal as an output 1 = selects the rxsync signal as an input
xrt86vx38 35 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 1 sb_enb(1) r/w 0 receive slip buffer mode select these bits select modes of operation for the receive slip buffer. these two bits also select the direction of rx serclk and rxsync in base clock rate (2.048mhz). the following table shows the corresponding slip buffer modes as well as the direction of the rx sync/rxserclk according to the setting of these two bits. n ote : users must make sure that the rxse rclk input pin is synchronized to the recovered clock signal for this particular channel to prevent any buffer slips from occurring. 0 sb_enb(0) r/w 1 t able 20: fifo l atency r egister (ffolr) h ex a ddress : 0 x n117 b it f unction t ype d efault d escription -o peration 7-5 reserved - - reserved 4-0 rx slip buffer fifo latency[4:0] r/w 00100 receive slip buffer fifo latency[4:0]: these bits permit the user to spec ify the ?receive data? latency (in terms of rxserclk_n clock periods), whenever the receive slip buffer has been configured to operate in the ?fifo? mode. n ote : these bits are only active if the receive slip buffer has been configured to operate in the fifo mode. t able 19: s lip b uffer c ontrol r egister (sbcr) h ex a ddress : 0 x n116 b it f unction t ype d efault d escription -o peration sb_enb [1:0] r eceive s lip b uffer m ode s elect d irection of r x serclk d irection of r x sync 00/11 receive slip buffer is bypassed output output 01 slip buffer mode input depends on the setting of sb_sdir (bit 2 of this register) if sb_sdir = 0: rxsync = output if sb_sdir = 1: rxsync = input 10 fifo mode. fifo data latency can be programmed by the 'fifo latency register' (address = 0xn117). input depends on the setting of sb_sdir (bit 2 of this register) if sb_sdir = 0: rxsync = output if sb_sdir = 1: rxsync = input
xrt86vx38 36 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 21: dma 0 (w rite ) c onfiguration r egister (d0wcr) h ex a ddress : 0 x n118 b it f unction t ype d efault d escription -o peration 7 dma0 rst r/w 0 dma_0 reset this bit resets the transmit dma (write) channel 0. 0 = normal operation. 1 = a zero to one transition resets the transmit dma (write) channel 0. 6 dma0 enb r/w 0 dma_0 enable this bit enables the transmit dma_0 (w rite) interface. after a transmit dma is enabled, dma transfers ar e only requested when the transmit buffer status bits indicate that there is space for a complete message or cell. the dma write channel is used by the external dma controller to transfer data from the external memory to the hdlc buffers within the t1 framer. the dma write cycle starts by t1 framer asserting the dma request ( req0) ?low?, then the external dma controller should drive the dma acknowledge ( ack0) ?low? to indicate that it is ready to start the transfer. the external dma controller should place new data on the microprocessor data bus each time the write signal is strobed low if the wr is configured as a write strobe. if wr is configured as a direction signal, then the external dma controller would place new data on the microprocessor data bus each time the read signal (rd) is strobed low. 0 = disables the transmit dma_0 (write) interface 1 = enables the transmit dma_0 (write) interface 5 wr type r/w 0 write type select this bit selects the function of the wr signal. 0 = wr functions as a direction signal (indicates whether the current bus cycle is a read or write operation) and rd functions as a data strobe signal. 1 = wr functions as a write strobe signal 4 - 3 reserved - - reserved 2 dma0_chan(2) r/w 0 channel select these three bits select which t1 channel within the xrt86vx38 uses the transmit dma_0 (write) interface. 000 = channel 0 001 = reserved 001 = channel 2 011 = reserved 1xx = reserved 1 dma0_chan(1) r/w 0 0 dma0_chan(0) r/w 0
xrt86vx38 37 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 22: dma 1 (r ead ) c onfiguration r egister (d1rcr) h ex a ddress : 0 x n119 b it f unction t ype d efault d escription -o peration 7-6 reserved - - reserved 7 dma1 rst r/w 0 dma_1 reset this bit resets the receive dma (read) channel 1 0 = normal operation. 1 = a zero to one transition resets the receive dma (read) channel 1. 6 dma1 enb r/w 0 dma1_enb this bit enables the receive dma_1 (read) interface. after a receive dma is enabled, dma transfers ar e only requested when the receive cell buffer contains a co mplete message or cell. the dma read channel is used by th e t1 framer to transfer data from the hdlc buffers within the t1 framer to external memory. the dma read cycle starts by t1 framer asserting the dma request ( req1) ?low?, then the external dma contro ller should drive the dma acknowl - edge ( ack1) ?low? to indicate that it is ready to receive the data. the t1 framer should place new data on the microprocessor data bus each time the read signal is strobed low if the rd is configured as a read strobe. if rd is configured as a dire ction signal, then the t1 framer would place new data on the microprocessor data bus each time the write signal (wr) is strobed low. 0 = disables the dma_1 (read) interface 1 = enables the dma_1 (read) interface 5 rd type r/w 0 read type select this bit selects the function of the rd signal. 0 = rd functions as a read strobe signal 1 = rd acts as a direction signal (indicates whether the current bus cycle is a read or write operation), and wr works as a data strobe. 4 - 3 reserved - - reserved 2 dma1_chan(2) r/w 0 channel select these three bits select which t1 channel within the chip uses the receive dma_1 (read) interface. 000 = channel 0 001 = reserved 001 = channel 2 011 = reserved 1xx = reserved 1 dma1_chan(1) r/w 0 0 dma1_chan(0) r/w 0
xrt86vx38 38 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 23: i nterrupt c ontrol r egister (icr) h ex a ddress : 0 x n11a b it f unction t ype d efault d escription -o peration 7-3 reserved - - reserved 2 int_wc_rur r/w 0 interrupt write-to-clear or reset-upon-read select this bit configures all interrupt status bits to be either reset upon read or write-to-clear 0= configures all interrupt status bits to be reset-upon-read (rur). 1= configures all interrupt status bits to be write-to-clear (wc). 1 enbclr r/w 0 interrupt enable auto clear this bit configures all interrupt enable bits to clear or not clear after reading the interrupt status bit. 0= configures all interrupt enable bits to not cleared after reading the interrupt status bit. the corresponding interrupt enable bit will stay ?high? after reading the interrupt status bit. 1= configures all interrupt enable bits to clear after reading the interrupt status bit. the corresponding interrupt enable bit will be set to ?low? after reading the interrupt status bit. 0 intrup_enb r/w 0 interrupt enable for framer_n this bit enables or disables the entire t1 framer block for interrupt generation. 0 = disables the t1 framer block for interrupt generation 1 = enables the t1 framer block for interrupt generation
xrt86vx38 39 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 24: lapd s elect r egister (lapdsr) h ex a ddress : 0 x n11b b it f unction t ype d efault d escription -o peration [7:5] reserved - - reserved 4 hdlc3en r/w 1 hdlc controller 3 enable this bit is used to enable or disable hdlc controller 3. by default, the hdlc controller is enabled, this bit set to "1". if the hdlc con - troller is disabled while transmitting a message, bos will disrupt the transmission and send all ones, mos will send the flag sequence. 0 - disabled 1 - enabled 3 hdlc2en r/w 1 hdlc controller 2 enable this bit is used to enable or disable hdlc controller 2. by default, the hdlc controller is enabled, this bit set to "1". if the hdlc con - troller is disabled while transmitting a message, bos will disrupt the transmission and send all ones, mos will send the flag sequence. 0 - disabled 1 - enabled 2 hdlc1en r/w 1 hdlc controller 1 enable this bit is used to enable or disable hdlc controller 1. by default, the hdlc controller is enabled, this bit set to "1". if the hdlc con - troller is disabled while transmitting a message, bos will disrupt the transmission and send all ones, mos will send the flag sequence. 0 - disabled 1 - enabled [1:0] hdlc controller select[1:0] r/w 0 hdlc controller select[1:0]: these bits permit the user to select any of the three (3) hdlc con - trollers that he/she will use within this particular channel, as depicted below. 00 & 11 - selects hdlc controller # 1 01 - selects hdlc controller # 2 10 - selects hdlc controller # 3
xrt86vx38 40 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 25: c ustomer i nstallation a larm g eneration r egister (ciagr) h ex a ddress : 0 x n11c b it f unction t ype d efault d escription -o peration [7:4] reserved - - reserved [3:2] ciag r/w 00 ci alarm transmit (only in esf) these two bits are used to enable or disable ais-ci or rai-ci gen - eration in t1 esf mode only. alarm indication signal-customer installation (ais-ci) and remote alarm indication-customer installation (rai-ci) are intended for use in a network to differentiate betw een an issue within the network or the customer installation (ci). ais-ci ais-ci is an all ones signal with an embedded signature of 01111100 11111111 (right-to left) which recurs at 386 bit intervals in- the ds-1 signal. rai-ci remote alarm indication - customer installation (rai-ci) is a repeti - tive pattern with a period of 1.08 seconds. it comprises 0.99 sec - onds of rai message (00000000 11111111 right-to-left) and a 90 ms of rai-ci signature (00111110 11111111 right to left) to form a rai-ci signal. rai-ci applies to t1 esf framing mode only. 00/11 = disables rai-ci or ais-ci alarms generation 01 = enables unframed ais-ci alarm generation 10 = enables rai-ci alarm generation [1:0] ciad r/w 00 ci alarm detect (only in esf) these two bits are used to enable or disable rai-ci or ais-ci alarm detection in t1 esf mode only. 00/11 = disables the rai-ci or ais-ci alarm detection 01 = enables the unframed ais-ci alarm detection 10 = enables the rai-ci alarm detection
xrt86vx38 41 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 26: p erformance r eport c ontrol r egister (prcr) h ex a ddress : 0 x n11d b it f unction t ype d efault d escription -o peration 7 lbo_adj_enb r/w 0 transmit line build out auto adjustment: this bit is used to enable or disable the transmit line build out auto adjustment feature. when the tran smitter of the device is sending ais condition, the transmit line build out will automatically be adjust to one setting lower if this feature is enabled. (please refer to the eqc[4:0] bits in register 0xnf00 for different settings of transmit line build out). this feature is designed to for power saving pur - poses when an ais signal is being transmitted. 1 - enables the transmit line build out auto adjustment feature. 0 - disables the transmit line buil d out auto adjustment feature. n ote : this feature is only available for t1 short haul applications. 6 rlos_out_enb r/w 1 rlos output enable: this bit is used to enable or disable the receive los (rlos_n) out - put pins. when this bit is set "low ", the rlos_n pin will be tri-stated for all conditions. when this bit is set "high", the rlos_n pin will pull "high" during a los condition and pull "low" when data is present on rtip/rring. 0 - disables the rlos output pin. 1 - enables the rlos output pin. [5-3] reserved - - reserved. 2 c/r_bit r/w 0 c/r bit control this bit allows user to control t he value of c/r bit within an outgoing performance report. 0 - outgoing c/r bit will be set to?0? 1 - outgoing c/r bit will be set to?1? [1:0] apcr r/w 00 automatic performance control/response report these bits automatically generate s a summary report of the pmon status so that it can be inserted into an out going lapd message. automatic performance report can be generated every time these bits transition from ?b00? to ?b01?or automatically every one second. the table below describes the different apcr[1:0] bits settings. apcr[1:0] s ource for r eceive d/e t imeslots 00/11 no performance report issued 01 single performance report is issued when these bits transitions from ?b00? to b?01?. 10 automatically issues a performance report every one second
xrt86vx38 42 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 27: g apped c lock c ontrol r egister (gccr) h ex a ddress : 0 x n11e b it f unction t ype d efault d escription -o peration 7 froutclk r/w 0 framer output clock reference this bit is used to enable or disable high-speed t1 rate on the t1oscclk and the e1oscclk output pins. by default, the output clock reference on t1oscclk and e1oscclk output pins are set to 1.544mhz/2.048mhz respectively. by setting this bit to a ?1?, t he output clock reference on the t1osclk and the e1oscclk are changed to 49.408mhz/ 65.536mhz respectively. 0 = disables high-speed rate to be output on the t1oscclk and e1oscclk output pins. 1 = enables high-speed rate to be output on the t1oscclk and e1oscclk output pins. [6:2] reserved - - reserved 1 txgccr r/w 0 transmit gapped clock interface this bit is used to enable or disable the transmit gapped clock inter - face operating at 2.048mbit/s in ds -1 mode. in this application, 63 gaps (missing data) are inserted so that the overall bit rate is reduced to 1.544mbit/s. if the transmit gapped clock interface is enabled: txmsync is used as the 2.048mhz gapped clock input. txser is used as the 2.048mhz gapped data input. txserclk must be a 1.544mhz clock input. 0 = disables the transmit gapped clock interface. 1 = enables the transmit gapped clock interface. 0 rxgccr r/w 0 receive gapped clock interface this bit is used to enable or disable the receive gapped clock inter - face operating at 2.048mbit/s in ds -1 mode. in this application, 63 gaps (missing data) are extracted so that the overall bit rate is reduced to 1.544mbit/s. if the receive gapped clock interface is enabled: rxserclk should be configured as a gapped clock input at 2.048mhz so that a 2.048mhz gapped clock can be applied to the framer block. rxser is used as the 2.048mhz gapped data output. the position of the gaps will be determined by the gaps placed on rxserclk by the user. 0 = disables the receive gapped clock interface 1 = enables the receive gapped clock interface
xrt86vx38 43 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 28: t ransmit i nterface c ontrol r egister (ticr) h ex a ddress :0 x n120 b it f unction t ype d efault d escription -o peration 7 txsyncfrd r/w 0 tx synchronous fraction data interface this bit selects whether txchclk or txserclk will be used for fractional data input if fractional interface is enabled. if txserclk is selected to clock in fractional data input, txchclk will be used as an enable signal 0 = fractional data is clocked into the chip using txchclk if fractional data interface is enabled. 1 = fractional data is clocked into the chip using txserclk. txchclk is used as fractional data enable. n ote : the time slot identifier pins (txchn[4:0]) still indicates the time slot number if fractional data interface is not enabled. fractional interface can be enabled by setting txfr1544 to 1 6 reserved - - reserved 5 txplclkenb/ txsync is low r/w 0 transmit payload clock enable/txsync is active low this exact function of this bit depends on whether the t1 fram er is configured to operate in base rate or high speed modes of operation. if the t1 framer is configured to operate in base rate - txpayload clock: this bit configures the framer to output a regular clock or a payload clock on the transmit serial clock (txserclk) pin when txserclk is configured to be an output. 0 = configures the framer to output a 1.544mhz clock on the txserclk pin when txserclk is configured as an output. 1 = configures the framer to output a 1.544mhz clock on the txserclk pin when transmitting payload bits. ther e will be gaps on the txserclk output pin when transmitting overhead bits. if the t1 framer is configured to operate in high-speed or multiplexed modes - txsync is active low: this bit is used to select whether th e transmit frame boundary (txsync) is active low or active high. 0 = selects txsync to be active ?high? 1 = selects txsync to be active ?low?
xrt86vx38 44 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description 4 txfr1544 r/w 0 fractional/signaling interface enabled this bit is used to enable or disable the transmit fractional data interface, sig - naling input, as well as the 32mhz tr ansmit clock and the transmit overhead signal output. 0 = configures the 5 time slot identifier pins (txchn[4:0]) to output the channel number as usual. 1 = configures the 5 time slot identifier pins (txchn[4:0]) to function as the fol - lowing: txchn[0] becomes the transmit serial signaling pin (txsig_n) for signaling inputs. signaling data can now be input from the txsig pin if configured appropriately. txchn[1] becomes the transmit fractional data input pin (txfrtd_n) for frac - tional data input. fractional data can no w be input from the txfrtd pin if con - figured appropriately. txchn[2] becomes the 32 mhz transmit clock output txchn[3] becomes the transmit overhe ad signal which pulses high on the first bit of each multi-frame. n ote : this bit has no effect in the hi gh speed or multiplexed modes of operation. in high-speed or multiplexed modes, txchn[0] functions as txsign for signaling input. 3 txiclkinv r/w 0 transmit clock inversion (backplane interface) this bit selects whether data transition will happen on the rising or falling edge of the transmit clock. 0 = selects data transition to happen on the rising edge of the transmit clocks. 1 = selects data transition to happen on the falling edge of the transmit clocks. n ote : this feature is only available for base rate configuration (i.e. non- highspeed, and non-multiplexed modes). 2 txmuxen r/w 0 multiplexed mode enable this bit enables or disables the multip lexed mode. when multiplexed mode is enable, multiplexed data of four chan nels at 12.352 or 16.384mhz are demul - tiplexed inside the transmit framer and sent to 2 channels on the line side. the backplane speed will be running at either 12.352 or 16.384mhz depending on the multiplexed mode selected by tx imode[1:0] of this register. 0 = disables the multiplexed mode. 1 = enables the multiplexed mode. t able 28: t ransmit i nterface c ontrol r egister (ticr) h ex a ddress :0 x n120 b it f unction t ype d efault d escription -o peration
xrt86vx38 45 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 1-0 tximode[1:0] r/w 00 transmit interface mode selection this bit determines the transmit interface speed. the exact function of these two bits depends on whether multiplexed mode is enabled or disabled. ta b l e 29 and table 30 shows the functions of these two bits for non-multi - plexed and multiplexed modes.: t able 28: t ransmit i nterface c ontrol r egister (ticr) h ex a ddress :0 x n120 b it f unction t ype d efault d escription -o peration t able 29: t ransmit i nterface s peed w hen m ultiplexed m ode is d isabled (t x muxen = 0) t x imode[1:0] t ransmit i nterface s peed 00 1.544mbit/s base rate mode: transmit backplane interface signals include: txserclk is an input or output clock at 1.544mhz txmsync is the superframe boundary at 3ms (esf) or 1.5ms (sf) txsync is the single frame boundary at 125 us txser is the base-rate data input 01 2.048mbit/s (high-speed mvip mode): transmit backplane interface signals include: txserclk is an input clock at 1.544mhz txmsync is the high speed input clock at 2.048mhz to input high-speed data txsync can be configured as a single frame or super- frame boundary, depending on the setting of bit 5 of reg- ister 0xn109 txser is the high-speed data input 10 4.096mbit/s high-speed mode: transmit backplane interface signals include: txserclk is an input clock at 1.544mhz txmsync will become the high speed input clock at 4.096mhz to input high-speed data txsync can be configured as a single frame or super- frame boundary, depending on the setting of bit 5 of reg- ister 0xn109 txser is the high-speed data input 11 8.192mbit/s high-speed mode: transmit backplane interface signals include: txserclk is an input clock at 1.544mhz txmsync will become the high speed input clock at 8.192mhz to input high-speed data txsync can be configured as a single frame or super- frame boundary, depending on the setting of bit 5 of reg- ister 0xn109 txser is the high-speed data input
xrt86vx38 46 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description 1-0 tximode[1:0] r/w 00 ( continued) transmit backplane interface signals include: txserclk is an input clock at 1.544mhz txmsync will become the highspeed input clock at 12.352 or 16.384mhz to input high-speed multiplexed data on the back-plane interface txsync can be configured as a singl e frame or super-frame boundary, depending on the setting of bit 5 of register 0xn109 txser is the high-speed data input n ote : in high speed mode, transmit data is sampled on the rising edge of the 12mhz or 16mhz clock edge. t able 28: t ransmit i nterface c ontrol r egister (ticr) h ex a ddress :0 x n120 b it f unction t ype d efault d escription -o peration t able 30: t ransmit i nterface s peed when m ultiplexed m ode is e nabled (t x muxen = 1) t x imode[1:0] t ransmit i nterface s peed 00 bit-multiplexed mode at 12.352mhz is enabled: transmit backplane interface is taking four-channel mul- tiplexed data at a rate of 12.352mbit/s from channel 0 and bit-demultiplexing the serial data into 4 channels and output to the line on channels 0 through 3. the txsync signal pulses ?high? during the framing bit of each ds-1 frame. 01 bit-multiplexed mode at 16.384mhz is enabled: transmit backplane interface is taking four-channel mul- tiplexed data at a rate of 16.384mbit/s from channel 0 and bit-demultiplexing the serial data into 4 channels and output to the line on channels 0 through 3. the txsync signal pulses ?high? during the framing bit of each ds-1 frame. 10 hmvip high-speed multiplexed mode enabled: transmit backplane interface is taking four-channel mul- tiplexed data at a rate of 16.384mbit/s from channel 0 and byte-demultiplexing the serial data into 4 channels and output on channels 0 through 3. the txsync signal pulses ?high? during the last two bits of the previous ds- 1 frame and the first two bits of the current ds-1 frame. 11 h.100 high-speed multiplexed mode enabled: transmit backplane interface is taking four-channel mul- tiplexed data at a rate of 16.384mbit/s from channel 0 and byte-demultiplexing the serial data into 4 channels and output to the line on channels 0 through 3. the txsync signal pulses ?high? during the last bit of the previous ds-1 frame and the first bit of the current ds-1 frame.
xrt86vx38 47 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 31: bert c ontrol & s tatus r egister (bertcsr0) h ex a ddress : 0 x n121 b it f unction t ype d efault d escription -o peration 7-4 reserved - - these bits are not used 3 bert_switch r/w 0 bert switch this bit enables or disables the bert switch function within the xrt86vx38 device. by enabling the bert switch function, bert functionality will be switched between the receive and transmit framer. t1 receive framer will generate the bert pattern and insert it onto the receive backplane interface, and t1 tran smit framer will be monitoring the transmit backplane interface for bert pattern and declare bert lock if bert has locked onto the input pattern. if bert switch is disabled, t1 transmit framer will generate the bert pattern to the line interface and the receive framer will be monitoring the line for bert pattern and declare bert lock if bert has locked onto the input pattern. 0 = disables the bert switch feature. 1 = enables the bert switch feature. 2 ber[1] r/w 0 bit error rate this bit is used to insert bert bit error at the rates presented at the table below. the exact function of this bit depends on whether bert switch function is enabled or not. (bit 3 within this register). if the bert switch function is disabled, bit error will be inserted by the t1 transmit framer out to the li ne interface if this bit is enabled. if the bert switch function is enabled, bit error will be inserted by the t1 receive framer out to the receive backplane interface if this bit is enabled. 1 ber[0] r/w 0 ber[1:0] bit error rate 00/11 disable bit error insertion to the transmit output or receive backplane interface 01 bit error is inserted to the transmit output or receive backplane interface at a rate of 1/1000 (one out of one thousand) 10 bit error is inserted to the transmit output or receive backplane interface at a rate of 1/ 1,000,000 (one out of one million)
xrt86vx38 48 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description 0 unframedbert r/w 0 unframed bert pattern this bit enables or disables unframed bert pattern generation (i.e. all timeslots and framing bits are all bert data). the exact function of this bit depends on whether bert switch function is enabled or not. (bit 3 within this register). if bert switch function is disabled, t1 transmit framer will gener - ate an unframed bert pattern to the line side if this bit is enabled. if prbs switch function is enabl ed, t1 receive framer will generate an unframed bert pattern to the receive backplane interface if this bit is enabled. 0 - enables an unframed bert pattern generation to the line inter - face or to the receive backplane interface 1 - disables an unframed bert pattern generation to the line inter - face or to the receive backplane interface t able 31: bert c ontrol & s tatus r egister (bertcsr0) h ex a ddress : 0 x n121 b it f unction t ype d efault d escription -o peration
xrt86vx38 49 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 32: r eceive i nterface c ontrol r egister (ricr) h ex a ddress : 0 x n122 b it f unction t ype d efault d escription -o peration 7 rxsyncfrd r/w 0 receive synchronous fraction data interface this bit selects whether rxchclk or rxserclk will be used for fractional data output if receive fractional interf ace is enabled. if rxserclk is selected to clock out fractional data, rxchclk will be used as an enable signal 0 = fractional data is clocked out of the chip using rxchclk if the receive fractional interface is enabled. 1 = fractional data is clocked out of the chip using rxserclk if the receive fractional interface is enabled. rxchclk is used as fractional data enable. n ote : the time slot identifier pins (rxchn[ 4:0]) still indicates the time slot number if the receive fractional data interface is not enabled. fractional interface can be en abled by setting rxfr1544 to 1 6 reserved - - reserved 5 rxplclkenb/ rxsync is low r/w 0 receive payload clock enable/rxsync is active low this exact function of this bit depends on whether the t1 framer is configured to operate in base rate or high speed modes of operation. if the t1 framer is configured to operate in base rate - txpayload clock: this bit configures the t1 framer to ei ther output a regular clock or a payload clock on the receive serial clock (rxserclk) pin when rxserclk is config - ured to be an output. 0 = configures the framer to output a 1.544mhz clock on the rxserclk pin when rxserclk is configured as an output. 1 = configures the framer to output a 1.544mhz clock on the rxserclk pin when receiving payload bits. there will be gaps on the rxserclk output pin when receiving overhead bits. if the t1 framer is configured to operate in high-speed or multiplexed modes - rxsync is active low: this bit is used to select whether the receive frame boundary (rxsync) is active low or active high. 0 = selects rxsync to be active ?high? 1 = selects rxsync to be active ?low?
xrt86vx38 50 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description 4 rxfr1544 r/w 0 receive fractional/signaling interface enabled this bit is used to enable or disable th e receive fractional output interface, receive signaling output, the serial ch annel number output, as well as the 8khz and the received recovered clock output. this bit only functions when the device is configured in non-high speed or multiplexed modes of opera - tions. if the device is configured in base rate: 0 = configures the 5 time slot identifie r pins (rxchn[4:0]) to output the chan - nel number in parallel as usual. 1 = configures the 5 time slot identifier pins (rxchn[4:0]) into the following dif - ferent functions: rxchn[0] becomes the receive serial si gnaling output pin (rxsig_n) for sig - naling outputs. signaling data can now be output to the rx sig pin if config - ured appropriately. rxchn[1] becomes the receive fractional data output pin (rxfrtd_n) for fractional data output. fractional data can now be output to the rxfrtd pin if configured appropriately. rxchn[2] outputs the serial channel number rxchn[3] outputs an 8khz clock signal. rxchn[4] outputs the received recovered clock signal (1.544mhz for t1) n ote : this bit has no effect in the high speed or multiplexed modes of operation. in high-speed or multip lexed modes, rxchn[0] outputs the signaling data and rxchn[4] outputs the recovered clock. 3 rxiclkinv n/a 0 receive clock inversion (backplane interface) this bit selects whether data transition will happen on the rising or falling edge of the receive clock. 0 = selects data transition to happen on the rising edge of the receive clocks. 1 = selects data transition to happen on the falling edge of the receive clocks. n ote : this feature is only available for base rate configuration (i.e. non- highspeed, or non-multiplexed modes). 2 rxmuxen r/w 0 receive multiplexed mode enable this bit enables or disables the multip lexed mode on the receive side. when multiplexed mode is enable, data of fo ur channels from the line side are multi - plexed onto one serial stream inside the receive framer and output to the back-plane interface on rxser. the backplane speed will become either 12.352mhz or 16.384mhz once multiplexed mode is enabled. 0 = disables the multiplexed mode. 1 = enables the multiplexed mode. t able 32: r eceive i nterface c ontrol r egister (ricr) h ex a ddress : 0 x n122 b it f unction t ype d efault d escription -o peration
xrt86vx38 51 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 1-0 rximode[1:0] r/w 00 receive interface mode selection[1:0] this bit determines the receive backpla ne interface speed. the exact func - tion of these two bits depends on whether receive multiplexed mode is enabled or disabled. table 33 and table 34 shows the functions of these two bits for non-multiplexed and multiplexed modes.: t able 32: r eceive i nterface c ontrol r egister (ricr) h ex a ddress : 0 x n122 b it f unction t ype d efault d escription -o peration t able 33: r eceive i nterface s peed w hen m ultiplexed m ode is d isabled (t x muxen = 0) r x imode[1:0] r eceive i nterface s peed 00 1.544mbit/s base rate mode receive backplane interface signals include: rxserclk is an input or output clock at 1.544mhz rxsync is an input or output signal which indicates the receive singe frame boundary rxser is the base-rate data output 01 2.048mbit/s high-speed mvip mode: receive backplane interface signals include: rxserclk is an input clock at 2.048mhz rxsync is an input signal which indicates the receive singe frame boundary rxser is the high-speed data output 10 4.096mbit/s high-speed mode: receive backplane interface signals include: rxserclk is an input clock at 4.096mhz rxsync is an input signal which indicates the receive singe frame boundary rxser is the high-speed data output 11 8.192mbit/s high-speed mode: receive backplane interface signals include: rxserclk is an input clock at 8.192mhz rxsync is an input signal which indicates the receive singe frame boundary rxser is the high-speed data output
xrt86vx38 52 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description 1-0 rximode[1:0] r/w 00 (continued) : ( receive backplane interface signals include: rxserclk is an input clock at either 12.352mhz or16.384mhz depending on the selected multiplexed mode. rxsync is an input signal which indicates the multiplexed frame boundary. the length of rxsync depends on the multiplexed mode selected. rxser is the high-speed data output n ote : in high speed mode, receive data is clocked out on the rising edge of the 12mhz or 16mhz clock edge. t able 32: r eceive i nterface c ontrol r egister (ricr) h ex a ddress : 0 x n122 b it f unction t ype d efault d escription -o peration t able 34: r eceive i nterface s peed when m ultiplexed m ode is e nabled (t x muxen = 1) t x imode[1:0] t ransmit i nterface s peed 00 bit-multiplexed mode at 12.352mhz is enabled: receive backplane interface is taking data from the four liu input channels 0 through 3 and bit-multiplexing the four-channel data into one 12.352mhz serial stream and output on channel 0 of t he receive serial output (rxser). the rxsync signal pulses ?high? during the framing bit of each ds-1 frame. 01 bit-multiplexed mode at 16.384mhz is enabled: receive backplane interface is taking data from the four liu input channels 0 through 3 and bit-multiplexing the four-channel data into one 16.384mhz serial stream and output to channel 0 of the receive serial output (rxser). the rxsync signal pulses ?high? during the framing bit of each t1 frame. 10 hmvip high-speed multiplexed mode enabled: receive backplane interface is taking data from the four liu input channels 0 through 3 and byte-multiplexing the four-channel data into one 16.384mhz serial stream and output to channel 0 of the receive serial output (rxser). the rxsync signal pulses ?high? during the last two bits of the previous t1 frame and the first two bits of the current t1 frame. 11 h.100 high-speed multiplexed mode enabled: receive backplane interface is taking data from the four liu input channels 0 through 3 and byte-multiplexing the four-channel data into one 16.384mhz serial stream and output to channel 0 of the receive serial output (rxser). the rxsync signal pulses ?high? during the last bit of the previous t1 frame and the first bit of the current t1 frame.
xrt86vx38 53 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 35: bert c ontrol & s tatus r egister (bertcsr1) h ex a ddress : 0 x n123 b it f unction t ype d efault d escription -o peration 7 prbstyp r/w 0 prbs pattern type this bit selects the type of prbs pattern that the t1 transmit/ receive framer will generate or detect. prbs 15 (x 15 + x 14 +1) polynomial or qrts (quasi-random test signal) pattern can be generated by the transmit or rece ive framer depending on whether prbs switch function is enabled or not (bit 3 in register 0xn121). if the prbs switch function is dis abled, t1 transmit framer will gen - erate either prbs 15 or qrts pa ttern and output to the line inter - face. prbs 15 or qrts pattern depends on the setting of this bit. if the prbs switch function is enabled, t1 receive framer will gener - ate either prbs 15 or qrts patter n and output to the receive back plane interface. prbs 15 or qrts pattern depends on the setting of this bit. 0 = enables the prbs 15 (x 15 + x 14 +1) polynomial generation. 1 = enables the qrts (quasi-random test signal) pattern genera - tion. 6 errorins r/w 0 error insertion this bit is used to insert a single bert error to the transmit or receive output depending on whether bert switch function is enabled or not. (bit 3 in register 0xn121). if the bert switch function is disabl ed, t1 transmit framer will insert a single bert error and output to the line interface if this bit is enabled. if the bert switch function is enabled, t1 receive framer will insert a single bert error and output to the receive back plane interface if this bit is enabled. a ?0? to ?1? transition will cause one output bit inverted in the bert stream. n ote : this bit only works if bert generation is enabled. 5 datainv r/w 0 bert data invert: this bit inverts the transmit bert output data and the receive bert input data. the exact function of this bit depends on whether bert switch function is enabled or not. (bit 3 in register 0xn121). if the bert switch function is disabled and if this bit is enabled, t1 transmit framer will invert the bert data before it outputs to the line interface, and the t1 receive framer will invert the incoming bert data before it receives it. if the bert switch function and this bit are both enabled, t1 receive framer will invert the bert data before it outputs to the line inter - face, and the t1 transmit framer will invert the incoming bert data before it receives it. 0 - transmit and receive framer will not invert the transmit and receive bert data. 1 - transmit and receive framer will invert the transmit and receive bert data.
xrt86vx38 54 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description 4 rxbertlock ro 0 lock status this bit indicates whether or not the receive or transmit bert lock has obtained. the exact function of this bit depends on whether bert switch function is enabled or not. (bit 3 in register 0xn121). if the bert switch function is disabled, t1 receive framer will declare lock if bert has locked onto the input pattern. if the bert switch function is disabled, t1 transmit framer will declare lock if bert has locked onto the input pattern. 0 = indicates the receive bert has not locked onto the input pat - terns. 1 = indicates the receive bert has locked onto the input patterns. 3 rxbertenb r/w 0 receive bert detection/generation enable this bit enables or disables the receive bert pattern detection or generation. the exact function of this bit depends on whether bert switch function is enabled or not. (bit 3 in register 0xn121). if the bert switch function is disabled and if this bit is enabled, t1 receive framer will detect the incoming bert pattern from the line side and declare bert lock if incoming data locks onto the bert pattern. if the bert switch function and this bit are both enabled, t1 trans - mit framer will detect the incoming bert pattern from the transmit backplane interface and declare bert lock if incoming data locks onto the bert pattern. 0 = disables the receive bert pattern detection. 1 = enables the receive bert pattern detection. 2 txbertenb r/w 0 transmit bert generation enable this bit enables or disables the transmit bert pattern generator. the exact function of this bit depends on whether bert switch func - tion is enabled or not. (bit 3 in register 0xn121). if bert switch function is disabled, t1 transmit framer will gener - ate the bert pattern to the line side if this bit is enabled. if bert switch function is enabled, t1 receive framer will generate the bert pattern to the receive backplane interface if this bit is enabled. 0 = disables the transmit bert pattern generator. 1 = enables the transmit bert pattern generator. 1 rxbypass r/w 0 receive framer bypass this bit enables or disables the receive t1 framer bypass. 0 = disables the receive t1 framer bypass. 1 = enables the receive t1 framer bypass. 0 txbypass r/w 0 transmit framer bypass this bit enables or disables the transmit t1 framer bypass. 0 = disables the transmit t1 framer bypass. 1 = enables the transmit t1 framer bypass. t able 35: bert c ontrol & s tatus r egister (bertcsr1) h ex a ddress : 0 x n123 b it f unction t ype d efault d escription -o peration
xrt86vx38 55 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 36: l oopback c ode c ontrol r egister - c ode 0 (lccr0) h ex a ddress : 0 x n124 b it f unction t ype d efault d escription -o peration 7-6 rxlbcalen[1:0] r/w 00 receive loopback code activation length this bit determines the receive loopback code activation length. there are four lengths supported by the xrt86vx38 as presented in the table below: 5-4 rxlbcdlen[1:0] r/w 00 receive loopback code deactivation length this bit determines the receive loopback code deactivation length. there are four lengths supported by the xrt86vx38 as presented in the table below rxlbcalen[1:0] r eceive l oopback c ode a ctivation l ength 00 selects 4-bit receive loopback code activa- tion sequence 01 selects 5-bit receive loopback code activa- tion sequence 10 selects 6-bit receive loopback code activa- tion sequence 11 selects 7-bit receive loopback code activa- tion sequence rxlbcdlen[1:0] r eceive l oopback c ode d eactivation l ength 00 selects 4-bit receive loopback code deacti- vation sequence 01 selects 5-bit receive loopback code deacti- vation sequence 10 selects 6-bit receive loopback code deacti- vation sequence 11 selects 7-bit receive loopback code deacti- vation sequence
xrt86vx38 56 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description 3-2 txlbclen[1:0] r/w 00 transmit loopback code length this bit determines transmit loopback code length. there are four lengths supported by the xrt86vx38 as presented in the table below 1 framed r/w 0 framed loopback code this bit selects either framed or unframed loopback code generation in the transmit path. 0 = selects an ?unframed? loopback code for transmission. 1 = selects a ?framed? loopback code for transmission. 0 autoenb r/w 0 remote loopback automatically this bit configures the xrt86vx38 in remote loopback automati - cally upon detecting the loopback code activation code specified in the receive loopback code activation register if receive activa - tion loopback code is enabled (register address:0xn126). the xrt86vx38 will cancel the remote loopback upon detecting the loopback code deactivation code specified in the receive loopback code deactivation register if the receive deactivation loopback code is enabled. (register address:0xn127) 0 = disables automatic remote loopback upon detecting the receive activation code. 1 = enables automatic remote loopback upon detecting the receive activation code. n ote : this feature is only available on the loopcode 0 controller. loopcode generators 1 through 7 do not support this feature. t able 36: l oopback c ode c ontrol r egister - c ode 0 (lccr0) h ex a ddress : 0 x n124 b it f unction t ype d efault d escription -o peration txlbclen[1:0] t ransmit l oopback c ode activation l ength 00 selects 4-bit transmit loopback code sequence 01 selects 5-bit transmit loopback code sequence 10 selects 6-bit transmit loopback code sequence 11 selects 7-bit transmit loopback code sequence
xrt86vx38 57 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 37: t ransmit l oopback c oder r egister (tlcr) h ex a ddress : 0 x n125 b it f unction t ype d efault d escription -o peration 7-1 txlbc[6:0] r/w 1010101 transmit loopback code these seven bits determine the transmit loopback code. the msb of the transmit loopback code is loaded first for transmission. 0 txlbcenb r/w 0 transmit loopback code enable this bit enables loopback code generation in the transmit path. transmit loopback code is generat ed by writing the transmit loop - back code in this register and enabling it using this bit. the length and the format of the transmit loopback code is determined by the loopback code control register. 0 = disables the transmit loopback code generation. 1 = enables the transmit loopback code generation. t able 38: r eceive l oopback a ctivation c ode r egister - c ode 0 (rlacr0) h ex a ddress : 0 x n126 b it f unction t ype d efault d escription -o peration 7-1 rxlbac[6:0] r/w 1010101 receive activation loopback code these seven bits determine the receive loopback activation code. the msb of the receive activation loopback code is received first. 0 rxlbacenb r/w 0 receive activation loopback code enable this bit enables the receive loopback activation code detection. receive loopback activation co de is detected by writing the expected receive activation loopback code in this register and enabling it using this bit. the length and format of the receive loopback activation code is determined by the loopback code control register. 0 = disables the receive loopback code activation detection. 1 = enables the receive loopback code activation detection. t able 39: r eceive l oopback d eactivation c ode r egister - c ode 0 (rldcr0) h ex a ddress : 0 x n127 b it f unction t ype d efault d escription -o peration 7-1 rxlbdc[6:0] r/w 1010101 receive deactivation loopback code these seven bits determine the receive loopback deactivation code. the msb of the receive deactivation loopback code is received first. 0 rxlbdcenb r/w 0 receive deactivation loopback code enable this bit enables the receive loopback deactivation code detection. receive loopback deactivation code is detected by writing the expected receive deactivation loopback code in this register and enabling it using this bit. the length and format of the receive loopback deactivation code is determined by the loopback code control register. 0 = disables the receive loopback code deactivation detection. 1 = enables the receive loopback code deactivation detection.
xrt86vx38 58 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 40: r eceive l oop c ode d etection s witch (rlcds) h ex a ddress : 0 x n128 b it f unction t ype d efault d escription -o peration 7 rxlcdetswitch7 r/w 7 receive loopcode switch 7 if receive loopcode 7 is enabled, this bit will determine which input the loopcode will be detected on. by default, the loopcode is search - ing for the line side (rtip/rring). 0 - line side (rtip/rring) 1 - system side (txser) 6 rxlcdetswitch6 r/w 6 receive loopcode switch 6 if receive loopcode 6 is enabled, this bit will determine which input the loopcode will be detected on. by default, the loopcode is search - ing for the line side (rtip/rring). 0 - line side (rtip/rring) 1 - system side (txser) 5 rxlcdetswitch5 r/w 5 receive loopcode switch 5 if receive loopcode 5 is enabled, this bit will determine which input the loopcode will be detected on. by default, the loopcode is search - ing for the line side (rtip/rring). 0 - line side (rtip/rring) 1 - system side (txser) 4 rxlcdetswitch4 r/w 4 receive loopcode switch 4 if receive loopcode 4 is enabled, this bit will determine which input the loopcode will be detected on. by default, the loopcode is search - ing for the line side (rtip/rring). 0 - line side (rtip/rring) 1 - system side (txser) 3 rxlcdetswitch3 r/w 3 receive loopcode switch 3 if receive loopcode 3 is enabled, this bit will determine which input the loopcode will be detected on. by default, the loopcode is search - ing for the line side (rtip/rring). 0 - line side (rtip/rring) 1 - system side (txser) 2 rxlcdetswitch2 r/w 2 receive loopcode switch 2 if receive loopcode 2 is enabled, this bit will determine which input the loopcode will be detected on. by default, the loopcode is search - ing for the line side (rtip/rring). 0 - line side (rtip/rring) 1 - system side (txser)
xrt86vx38 59 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 1 rxlcdetswitch1 r/w 0 receive loopcode switch 1 if receive loopcode 1 is enabled, this bit will determine which input the loopcode will be detected on. by default, the loopcode is search - ing for the line side (rtip/rring). 0 - line side (rtip/rring) 1 - system side (txser) 0 rxlcdetswitch0 r/w 0 receive loopcode switch 0 if receive loopcode 0 is enabled, this bit will determine which input the loopcode will be detected on. by default, the loopcode is search - ing for the line side (rtip/rring). 0 - line side (rtip/rring) 1 - system side (txser) t able 41: d efect d etection e nable r egister (dder) h ex a ddress : 0 x n129 b it f unction t ype d efault d escription -o peration 7 defdet r/w 1 for defect detection per ansi t1. 231-1997 and t1.403-1999, user should leave this bit set to ?1?. t able 40: r eceive l oop c ode d etection s witch (rlcds) h ex a ddress : 0 x n128 b it f unction t ype d efault d escription -o peration
xrt86vx38 60 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 42: l oopback c ode c ontrol r egister - c ode 1 (lccr1) h ex a ddress : 0 x n12a b it f unction t ype d efault d escription -o peration 7-6 rxlbcalen[1:0] r/w 00 receive loopback code activation length this bit determines the receive loopback code activation length. there are four lengths supported as presented in the table below: 5-4 rxlbcdlen[1:0] r/w 00 receive loopback code deactivation length this bit determines the receive loopback code deactivation length. there are four lengths supported as presented in the table below 3-2 reserved r/w 00 reserved 1 framed r/w 0 framed loopback code this bit selects either framed or unframed loopback code generation in the transmit path. 0 = selects an ?unframed? loopback code for transmission. 1 = selects a ?framed? loopback code for transmission. 0 reserved r/w 0 reserved rxlbcalen[1:0] r eceive l oopback c ode a ctivation l ength 00 selects 4-bit receive loopback code activa- tion sequence 01 selects 5-bit receive loopback code activa- tion sequence 10 selects 6-bit receive loopback code activa- tion sequence 11 selects 7-bit receive loopback code activa- tion sequence rxlbcdlen[1:0] r eceive l oopback c ode d eactivation l ength 00 selects 4-bit receive loopback code deacti- vation sequence 01 selects 5-bit receive loopback code deacti- vation sequence 10 selects 6-bit receive loopback code deacti- vation sequence 11 selects 7-bit receive loopback code deacti- vation sequence
xrt86vx38 61 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 43: r eceive l oopback a ctivation c ode r egister - c ode 1 (rlacr1) h ex a ddress : 0 x n12b b it f unction t ype d efault d escription -o peration 7-1 rxlbac[6:0] r/w 1010101 receive activation loopback code these seven bits determine the receive loopback activation code. the msb of the receive activation loopback code is received first. 0 rxlbacenb r/w 0 receive activation loopback code enable this bit enables the receive loopback activation code detection. receive loopback activation co de is detected by writing the expected receive activation loopback code in this register and enabling it using this bit. the length and format of the receive loopback activation code is determined by the loopback code control register. 0 = disables the receive loopback code activation detection. 1 = enables the receive loopback code activation detection. t able 44: r eceive l oopback d eactivation c ode r egister - c ode 1 (rldcr1) h ex a ddress : 0 x n12c b it f unction t ype d efault d escription -o peration 7-1 rxlbdc[6:0] r/w 1010101 receive deactivation loopback code these seven bits determine the receive loopback deactivation code. the msb of the receive deactivation loopback code is received first. 0 rxlbdcenb r/w 0 receive deactivation loopback code enable this bit enables the receive loopback deactivation code detection. receive loopback deactivation code is detected by writing the expected receive deactivation loopback code in this register and enabling it using this bit. the length and format of the receive loopback deactivation code is determined by the loopback code control register. 0 = disables the receive loopback code deactivation detection. 1 = enables the receive loopback code deactivation detection.
xrt86vx38 62 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 45: l oopback c ode c ontrol r egister - c ode 2 (lccr2) h ex a ddress : 0 x n12d b it f unction t ype d efault d escription -o peration 7-6 rxlbcalen[1:0] r/w 00 receive loopback code activation length this bit determines the receive loopback code activation length. there are four lengths supported as presented in the table below: 5-4 rxlbcdlen[1:0] r/w 00 receive loopback code deactivation length this bit determines the receive loopback code deactivation length. there are four lengths supported as presented in the table below 3-2 reserved r/w 00 reserved 1 framed r/w 0 framed loopback code this bit selects either framed or unframed loopback code generation in the transmit path. 0 = selects an ?unframed? loopback code for transmission. 1 = selects a ?framed? loopback code for transmission. 0 reserved r/w 0 reserved rxlbcalen[1:0] r eceive l oopback c ode a ctivation l ength 00 selects 4-bit receive loopback code activa- tion sequence 01 selects 5-bit receive loopback code activa- tion sequence 10 selects 6-bit receive loopback code activa- tion sequence 11 selects 7-bit receive loopback code activa- tion sequence rxlbcdlen[1:0] r eceive l oopback c ode d eactivation l ength 00 selects 4-bit receive loopback code deacti- vation sequence 01 selects 5-bit receive loopback code deacti- vation sequence 10 selects 6-bit receive loopback code deacti- vation sequence 11 selects 7-bit receive loopback code deacti- vation sequence
xrt86vx38 63 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 46: r eceive l oopback a ctivation c ode r egister - c ode 2 (rlacr2) h ex a ddress : 0 x n12e b it f unction t ype d efault d escription -o peration 7-1 rxlbac[6:0] r/w 1010101 receive activation loopback code these seven bits determine the receive loopback activation code. the msb of the receive activation loopback code is received first. 0 rxlbacenb r/w 0 receive activation loopback code enable this bit enables the receive loopback activation code detection. receive loopback activation co de is detected by writing the expected receive activation loopback code in this register and enabling it using this bit. the length and format of the receive loopback activation code is determined by the loopback code control register. 0 = disables the receive loopback code activation detection. 1 = enables the receive loopback code activation detection. t able 47: r eceive l oopback d eactivation c ode r egister - c ode 2 (rldcr2) h ex a ddress : 0 x n12f b it f unction t ype d efault d escription -o peration 7-1 rxlbdc[6:0] r/w 1010101 receive deactivation loopback code these seven bits determine the receive loopback deactivation code. the msb of the receive deactivation loopback code is received first. 0 rxlbdcenb r/w 0 receive deactivation loopback code enable this bit enables the receive loopback deactivation code detection. receive loopback deactivation code is detected by writing the expected receive deactivation loopback code in this register and enabling it using this bit. the length and format of the receive loopback deactivation code is determined by the loopback code control register. 0 = disables the receive loopback code deactivation detection. 1 = enables the receive loopback code deactivation detection.
xrt86vx38 64 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 48: t ransmit l oop c ode g eneration s witch (tlcgs) h ex a ddress : 0 x n140 b it f unction t ype d efault d escription -o peration 7-1 reserved r/w 0 reserved 0 txlcgenswitch r/w 0 transmit loopcode switch if the transmit loopcode is enabled, this bit will determine which direction the loopcode will be trans mitted. by default, the loopcode is generated on the line side (ttip/tring). 0 - line side (ttip/tring) 1 - system side (rxser) t able 49: l oop c ode t imer s elect (lcts) h ex a ddress : 0 x n141 b it f unction t ype d efault d escription -o peration 7-3 reserved r/w 0 reserved 2-0 lctimer r/w 110 loopcode timer select these bits are used to select the timer value for declaring a valid loopcode detection for both activation and de-activation. by default, the timer is set to 5 seconds. 000 - do not use 001 - do not use 010 - 1 second 011 - 2 seconds 100 - 3 seconds 101 - 4 seconds 110 - 5 seconds 111 - 6 seconds t able 50: t ransmit sprm and nprm c ontrol r egister (tsprmcr) h ex a ddress : 0 x n142 b it f unction t ype d efault d escription -o peration 7 fc_bit r/w 0 nprm fc bit this bit is used to set the value of the fc bit field within the nprm report. 6 pa_bit r/w 0 nprm pa bit this bit is used to set the value of the pa bit field within the nprm report. 5 u1_bit r/w 0 u1 bit this bit provides the contents of the u1 bit within the outgoing sprm message.
xrt86vx38 65 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 4 u2_bit r/w 0 u2 bit this bit provides the contents of the u2 bit within the outgoing sprm message. 3-0 r_bit r/w 0000 r bit this bit provides the contents of the r bit within the outgoing sprm message. t able 50: t ransmit sprm and nprm c ontrol r egister (tsprmcr) h ex a ddress : 0 x n142 b it f unction t ype d efault d escription -o peration
xrt86vx38 66 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 51: d ata l ink c ontrol r egister (dlcr2) h ex a ddress : 0 x n143 b it f unction t ype d efault d escription -o peration 7 slc-96 data link enable r/w 0 slc?96 datalink enable this bit permits the user to configure the channel to support the transmission and reception of the ?slc-96 type? of data-link mes - sage. 0 - channel does not support the transmission and reception of ?slc-96? type of data-link messages. regular sf framing bits will be transmitted. 1 - channel supports the transmission and reception of the ?slc- 96? type of data-link messages. n ote : this bit is only active if th e channel has been configured to operate in either the slc-96 or the esf framing formats. 6 mos abort disable r/w 0 mos abort disable: this bit permits the user to either enable or disable the ?automatic mos abort? feature within transmit hdlc controller # 2. if the user enables this feature, then transmit hdlc controller block # 2 will automatically transmit the ab ort sequence (e.g., a zero fol - lowed by a string of 7 consecutive ?1s?) whenever it abruptly transi - tions from transmitting a mos type of message, to transmitting a bos type of message. if the user disables this feature, then the transmit hdlc controller block # 2 will not transmit the abort sequence, whenever it abruptly transitions from transmi tting a mos-type of message to transmitting a bos-type of message. 0 - enables the ?automat ic mos abort? feature 1 - disables the ?automatic mos abort? feature 5 rx_fcs_dis r/w 0 receive frame check sequence (fcs) verification enable/dis - able this bit permits the user to configure the receive hdlc controller block # 2 to compute and verify the fcs value within each incoming lapd message frame. 0 - enables fcs verification 1 - disables fcs verification 4 autorx r/w 0 auto receive lapd message this bit configures the receive hdlc controller block #2 to discard any incoming bos or lapd message frame that exactly match which is currently stored in the receive hdlc1 buffer. 0 = disables this ?auto discard? feature 1 = enables this ?auto discard? feature. 3 tx_abort r/w 0 transmit abort this bit configures the transmit hdlc controller block # 2 to trans - mit an abort sequence (string of 7 or more consecutive 1?s) to the remote terminal. 0 - configures the transmit hdlc controller block # 2 to function normally (e.g., not transmit the abort sequence). 1 - configures the transmit hdlc controller block # 2 to transmit the abort sequence.
xrt86vx38 67 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 2 tx_idle r/w 0 transmit idle (flag sequence byte) this bit configures the transmit hdlc controller block #2 to uncon - ditionally transmit a repeating string of flag sequence octets (0x7e) in the data link channel to the remote terminal. in normal condi - tions, the transmit hdlc controll er block will repeatedly transmit the flag sequence octet whenever there is no mos message to transmit to the remote terminal eq uipment. however, if the user invokes this ?transmit idle sequ ence? feature, th en the transmit hdlc controller block will unconditionally transmit a repeat - ing stream of the flag sequence octet (thereby overwriting all out - bound mos data-link messages). 0 - configures the transmit hdlc controller block # 2 to transmit data-link information in a ?normal? manner. 1 - configures the transmit hdlc controller block # 2 to transmit a repeating string of flag s equence octets (0x7e). n ote : this bit is ignored if the transmit hdlc2 controller is operating in the bos mode - bit 0 (mos/bos) within this register is set to 0. 1 tx_fcs_en r/w 0 transmit lapd message with frame check sequence (fcs) this bit permits the user to configure the transmit hdlc controller block # 2 to compute and append fcs octets to the ?back-end? of each outbound mos data-link message. 0 - configures the transmit hdlc controller block # 2 to not com - pute and append the fcs octets to the back-end of each outbound mos data-link message. 1 - configures the transmit hdlc controller block # 2 to com - pute and append the fcs octets to the back-end of each outbound mos data-link message. n ote : this bit is ignored if the tran smit hdlc2 controller has been configured to operate in the bos mode - bit 0 (mos/bos) within this register is set to 0. 0 mos/ bos r/w 0 message oriented signaling/bit oriented signaling send this bit permits the user to enable lapd transmission through hdlc controller block # 2 using either bos (bit-oriented signaling) or mos (message-oriented signaling) frames. 0 - transmit hdlc controller block # 2 bos message send. 1 - transmit hdlc controller block # 2 mos message send. n ote : this is not an enable bit. this bit must be set to "0" each time a bos is to be sent. t able 51: d ata l ink c ontrol r egister (dlcr2) h ex a ddress : 0 x n143 b it f unction t ype d efault d escription -o peration
xrt86vx38 68 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 52: t ransmit d ata l ink b yte c ount r egister (tdlbcr2) h ex a ddress : 0 x n144 b it f unction t ype d efault d escription -o peration 7 txhdlc2 bufavail/ bufsel r/w 0 transmit hdlc2 buffer available/buffer select this bit has different functions, depending upon whether the user is writing to or reading from this register, as depicted below. if the user is writing data into this register bit: 0 - configures the transmit hdlc2 controller to read out and trans - mit the data, residing within ?transmit hdlc2 buffer # 0", via the data link channel to the remote terminal equipment. 1 - configures the transmit hdlc2 controller to read out and trans - mit the data, residing within the ?transmit hdlc2 buffer #1?, via the data link channel to the remote terminal equipment. if the user is reading data from this register bit: 0 - indicates that ?transmit hdlc2 buffer # 0" is the next available buffer. in this case, if the user wishes to write in the contents of a new ?outbound? data link message into the transmit hdlc2 mes - sage buffer, he/she should proceed to write this message into ?transmit hdlc2 buffer # 0" - address location: 0xn600. 1 - indicates that ?transmit hdlc2 buffer # 1" is the next available buffer. in this case, if the user wishes to write in the contents of a new ?outbound? data link message into the transmit hdlc2 mes - sage buffer, he/she should proceed to write this message into ?transmit hdlc2 buffer # 1" - address location: 0xn700. n ote : if one of these transmit hdlc2 buffers contain a message which has yet to be completely read-in and processed for transmission by the transmit hdlc2 controller, then this bit will automatically reflect the value corresponding to the next available buffer when it is read. changing this bit to the in- use buffer is not permitted. 6-0 tdlbc[6:0] r/w 0000000 transmit hdlc2 message - byte count the exact function of these bits depends on whether the transmit hdlc 2 controller is configured to transmit mos or bos messages to the remote terminal equipment. in bos mode: these bit fields contain the number of repetitions the bos message must be transmitted before the transmit hdlc2 controller gener - ates the transmit end of transfer (txeot) interrupt and halts trans - mission. if these fields are set to 00000000, then the bos message will be transmitted for an indefinite number of times. in mos mode: these bit fields contain the length, in number of octets, of the mes - sage to be transmitted. the l ength of mos message specified in these bits include header bytes such as the sapi, tei, control field, however, it does not include the fcs bytes.
xrt86vx38 69 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 53: r eceive d ata l ink b yte c ount r egister (rdlbcr2) h ex a ddress : 0 x n145 b it f unction t ype d efault d escription -o peration 7 rbufptr r/w 0 receive hdlc2 buffer-pointer this bit identifies which receive hdlc2 buffer contains the most recently received hdlc2 message. 0 - indicates that receive hdlc2 buffer # 0 contains the contents of the most recently received hdlc message. 1 - indicates that receive hdlc2 buffer # 1 contains the contents of the most recently received hdlc message. 6-0 rdlbc[6:0] r/w 0000000 receive hdlc message - byte count the exact function of these bits depends on whether the receive hdlc controller block #2 is configured to receive mos or bos messages. in bos mode: these seven bits contain the num ber of repetitions the bos mes - sage must be received before the receive hdlc2 controller gener - ates the receive end of transfer (rxeot) interrupt. if these bits are set to ?0000000?, the message will be received indefinitely and no receive end of transfer (rxeot) interrupt will be generated. in mos mode: these seven bits contain the size in bytes of the hdlc2 message that has been received and writte n into the receive hdlc buffer. the length of mos message shown in these bits include header bytes such as the sapi, tei, control field, and the fcs bytes.
xrt86vx38 70 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 54: l oopback c ode c ontrol r egister - c ode 3 (lccr3) h ex a ddress : 0 x n146 b it f unction t ype d efault d escription -o peration 7-6 rxlbcalen[1:0] r/w 00 receive loopback code activation length this bit determines the receive loopback code activation length. there are four lengths supported as presented in the table below: 5-4 rxlbcdlen[1:0] r/w 00 receive loopback code deactivation length this bit determines the receive loopback code deactivation length. there are four lengths supported as presented in the table below 3-2 reserved r/w 00 reserved 1 framed r/w 0 framed loopback code this bit selects either framed or unframed loopback code generation in the transmit path. 0 = selects an ?unframed? loopback code for transmission. 1 = selects a ?framed? loopback code for transmission. 0 reserved r/w 0 reserved rxlbcalen[1:0] r eceive l oopback c ode a ctivation l ength 00 selects 4-bit receive loopback code activa- tion sequence 01 selects 5-bit receive loopback code activa- tion sequence 10 selects 6-bit receive loopback code activa- tion sequence 11 selects 7-bit receive loopback code activa- tion sequence rxlbcdlen[1:0] r eceive l oopback c ode d eactivation l ength 00 selects 4-bit receive loopback code deacti- vation sequence 01 selects 5-bit receive loopback code deacti- vation sequence 10 selects 6-bit receive loopback code deacti- vation sequence 11 selects 7-bit receive loopback code deacti- vation sequence
xrt86vx38 71 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 55: r eceive l oopback a ctivation c ode r egister - c ode 3 (rlacr3) h ex a ddress : 0 x n147 b it f unction t ype d efault d escription -o peration 7-1 rxlbac[6:0] r/w 1010101 receive activation loopback code these seven bits determine the receive loopback activation code. the msb of the receive activation loopback code is received first. 0 rxlbacenb r/w 0 receive activation loopback code enable this bit enables the receive loopback activation code detection. receive loopback activation co de is detected by writing the expected receive activation loopback code in this register and enabling it using this bit. the length and format of the receive loopback activation code is determined by the loopback code control register. 0 = disables the receive loopback code activation detection. 1 = enables the receive loopback code activation detection. t able 56: r eceive l oopback d eactivation c ode r egister - c ode 3 (rldcr3) h ex a ddress : 0 x n148 b it f unction t ype d efault d escription -o peration 7-1 rxlbdc[6:0] r/w 1010101 receive deactivation loopback code these seven bits determine the receive loopback deactivation code. the msb of the receive deactivation loopback code is received first. 0 rxlbdcenb r/w 0 receive deactivation loopback code enable this bit enables the receive loopback deactivation code detection. receive loopback deactivation code is detected by writing the expected receive deactivation loopback code in this register and enabling it using this bit. the length and format of the receive loopback deactivation code is determined by the loopback code control register. 0 = disables the receive loopback code deactivation detection. 1 = enables the receive loopback code deactivation detection.
xrt86vx38 72 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 57: l oopback c ode c ontrol r egister - c ode 4 (lccr4) h ex a ddress : 0 x n149 b it f unction t ype d efault d escription -o peration 7-6 rxlbcalen[1:0] r/w 00 receive loopback code activation length this bit determines the receive loopback code activation length. there are four lengths supported as presented in the table below: 5-4 rxlbcdlen[1:0] r/w 00 receive loopback code deactivation length this bit determines the receive loopback code deactivation length. there are four lengths supported as presented in the table below 3-2 reserved r/w 00 reserved 1 framed r/w 0 framed loopback code this bit selects either framed or unframed loopback code generation in the transmit path. 0 = selects an ?unframed? loopback code for transmission. 1 = selects a ?framed? loopback code for transmission. 0 reserved r/w 0 reserved rxlbcalen[1:0] r eceive l oopback c ode a ctivation l ength 00 selects 4-bit receive loopback code activa- tion sequence 01 selects 5-bit receive loopback code activa- tion sequence 10 selects 6-bit receive loopback code activa- tion sequence 11 selects 7-bit receive loopback code activa- tion sequence rxlbcdlen[1:0] r eceive l oopback c ode d eactivation l ength 00 selects 4-bit receive loopback code deacti- vation sequence 01 selects 5-bit receive loopback code deacti- vation sequence 10 selects 6-bit receive loopback code deacti- vation sequence 11 selects 7-bit receive loopback code deacti- vation sequence
xrt86vx38 73 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 58: r eceive l oopback a ctivation c ode r egister - c ode 4 (rlacr4) h ex a ddress : 0 x n14a b it f unction t ype d efault d escription -o peration 7-1 rxlbac[6:0] r/w 1010101 receive activation loopback code these seven bits determine the receive loopback activation code. the msb of the receive activation loopback code is received first. 0 rxlbacenb r/w 0 receive activation loopback code enable this bit enables the receive loopback activation code detection. receive loopback activation co de is detected by writing the expected receive activation loopback code in this register and enabling it using this bit. the length and format of the receive loopback activation code is determined by the loopback code control register. 0 = disables the receive loopback code activation detection. 1 = enables the receive loopback code activation detection. t able 59: r eceive l oopback d eactivation c ode r egister - c ode 4 (rldcr4) h ex a ddress : 0 x n14b b it f unction t ype d efault d escription -o peration 7-1 rxlbdc[6:0] r/w 1010101 receive deactivation loopback code these seven bits determine the receive loopback deactivation code. the msb of the receive deactivation loopback code is received first. 0 rxlbdcenb r/w 0 receive deactivation loopback code enable this bit enables the receive loopback deactivation code detection. receive loopback deactivation code is detected by writing the expected receive deactivation loopback code in this register and enabling it using this bit. the length and format of the receive loopback deactivation code is determined by the loopback code control register. 0 = disables the receive loopback code deactivation detection. 1 = enables the receive loopback code deactivation detection.
xrt86vx38 74 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 60: l oopback c ode c ontrol r egister - c ode 5 (lccr5) h ex a ddress : 0 x n14c b it f unction t ype d efault d escription -o peration 7-6 rxlbcalen[1:0] r/w 00 receive loopback code activation length this bit determines the receive loopback code activation length. there are four lengths supported as presented in the table below: 5-4 rxlbcdlen[1:0] r/w 00 receive loopback code deactivation length this bit determines the receive loopback code deactivation length. there are four lengths supported as presented in the table below 3-2 reserved r/w 00 reserved 1 framed r/w 0 framed loopback code this bit selects either framed or unframed loopback code generation in the transmit path. 0 = selects an ?unframed? loopback code for transmission. 1 = selects a ?framed? loopback code for transmission. 0 reserved r/w 0 reserved rxlbcalen[1:0] r eceive l oopback c ode a ctivation l ength 00 selects 4-bit receive loopback code activa- tion sequence 01 selects 5-bit receive loopback code activa- tion sequence 10 selects 6-bit receive loopback code activa- tion sequence 11 selects 7-bit receive loopback code activa- tion sequence rxlbcdlen[1:0] r eceive l oopback c ode d eactivation l ength 00 selects 4-bit receive loopback code deacti- vation sequence 01 selects 5-bit receive loopback code deacti- vation sequence 10 selects 6-bit receive loopback code deacti- vation sequence 11 selects 7-bit receive loopback code deacti- vation sequence
xrt86vx38 75 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 61: r eceive l oopback a ctivation c ode r egister - c ode 5 (rlacr5) h ex a ddress : 0 x n14d b it f unction t ype d efault d escription -o peration 7-1 rxlbac[6:0] r/w 1010101 receive activation loopback code these seven bits determine the receive loopback activation code. the msb of the receive activation loopback code is received first. 0 rxlbacenb r/w 0 receive activation loopback code enable this bit enables the receive loopback activation code detection. receive loopback activation co de is detected by writing the expected receive activation loopback code in this register and enabling it using this bit. the length and format of the receive loopback activation code is determined by the loopback code control register. 0 = disables the receive loopback code activation detection. 1 = enables the receive loopback code activation detection. t able 62: r eceive l oopback d eactivation c ode r egister - c ode 5 (rldcr5) h ex a ddress : 0 x n14e b it f unction t ype d efault d escription -o peration 7-1 rxlbdc[6:0] r/w 1010101 receive deactivation loopback code these seven bits determine the receive loopback deactivation code. the msb of the receive deactivation loopback code is received first. 0 rxlbdcenb r/w 0 receive deactivation loopback code enable this bit enables the receive loopback deactivation code detection. receive loopback deactivation code is detected by writing the expected receive deactivation loopback code in this register and enabling it using this bit. the length and format of the receive loopback deactivation code is determined by the loopback code control register. 0 = disables the receive loopback code deactivation detection. 1 = enables the receive loopback code deactivation detection.
xrt86vx38 76 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 63: l oopback c ode c ontrol r egister - c ode 6 (lccr6) h ex a ddress : 0 x n14f b it f unction t ype d efault d escription -o peration 7-6 rxlbcalen[1:0] r/w 00 receive loopback code activation length this bit determines the receive loopback code activation length. there are four lengths supported as presented in the table below: 5-4 rxlbcdlen[1:0] r/w 00 receive loopback code deactivation length this bit determines the receive loopback code deactivation length. there are four lengths supported as presented in the table below 3-2 reserved r/w 00 reserved 1 framed r/w 0 framed loopback code this bit selects either framed or unframed loopback code generation in the transmit path. 0 = selects an ?unframed? loopback code for transmission. 1 = selects a ?framed? loopback code for transmission. 0 reserved r/w 0 reserved rxlbcalen[1:0] r eceive l oopback c ode a ctivation l ength 00 selects 4-bit receive loopback code activa- tion sequence 01 selects 5-bit receive loopback code activa- tion sequence 10 selects 6-bit receive loopback code activa- tion sequence 11 selects 7-bit receive loopback code activa- tion sequence rxlbcdlen[1:0] r eceive l oopback c ode d eactivation l ength 00 selects 4-bit receive loopback code deacti- vation sequence 01 selects 5-bit receive loopback code deacti- vation sequence 10 selects 6-bit receive loopback code deacti- vation sequence 11 selects 7-bit receive loopback code deacti- vation sequence
xrt86vx38 77 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 64: r eceive l oopback a ctivation c ode r egister - c ode 6 (rlacr6) h ex a ddress : 0 x n150 b it f unction t ype d efault d escription -o peration 7-1 rxlbac[6:0] r/w 1010101 receive activation loopback code these seven bits determine the receive loopback activation code. the msb of the receive activation loopback code is received first. 0 rxlbacenb r/w 0 receive activation loopback code enable this bit enables the receive loopback activation code detection. receive loopback activation co de is detected by writing the expected receive activation loopback code in this register and enabling it using this bit. the length and format of the receive loopback activation code is determined by the loopback code control register. 0 = disables the receive loopback code activation detection. 1 = enables the receive loopback code activation detection. t able 65: r eceive l oopback d eactivation c ode r egister - c ode 6 (rldcr6) h ex a ddress : 0 x n151 b it f unction t ype d efault d escription -o peration 7-1 rxlbdc[6:0] r/w 1010101 receive deactivation loopback code these seven bits determine the receive loopback deactivation code. the msb of the receive deactivation loopback code is received first. 0 rxlbdcenb r/w 0 receive deactivation loopback code enable this bit enables the receive loopback deactivation code detection. receive loopback deactivation code is detected by writing the expected receive deactivation loopback code in this register and enabling it using this bit. the length and format of the receive loopback deactivation code is determined by the loopback code control register. 0 = disables the receive loopback code deactivation detection. 1 = enables the receive loopback code deactivation detection.
xrt86vx38 78 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 66: d ata l ink c ontrol r egister (dlcr3) h ex a ddress : 0 x n153 b it f unction t ype d efault d escription -o peration 7 slc-96 data link enable r/w 0 slc?96 datalink enable this bit permits the user to configure the channel to support the transmission and reception of the ?slc-96 type? of data-link message. 0 - channel does not support the transmission and reception of ?slc-96? type of data-link messages. regular sf framing bits will be transmitted. 1 - channel supports the transmission and reception of the ?slc-96? type of data-link messages. n ote : this bit is only active if the channel has been configured to operate in either the slc-96 or the esf framing formats. 6 mos abort disable r/w 0 mos abort disable: this bit permits the user to either enable or disable t he ?automatic mos abort? feature within transmit hdlc cont roller # 3. if the user enables this feature, then transmit hdlc controller block # 3 will automatically transmit the abort sequence (e.g., a zero foll owed by a string of 7 consecutive ?1s?) whenever it abruptly transitions from transmitting a mos type of mes - sage, to transmitting a bos type of message. if the user disables this feature, th en the transmit hdlc controller block # 3 will not transmit the abort sequence, whenever it abruptly transitions from transmitting a mos-type of messa ge to transmitting a bos-type of message. 0 - enables the ?automat ic mos abort? feature 1 - disables the ?automatic mos abort? feature 5 rx_fcs_dis r/w 0 receive frame check sequence (fcs) verification enable/disable this bit permits the user to configure the receive hdlc controller block # 3 to compute and verify the fcs value within each incoming lapd message frame. 0 - enables fcs verification 1 - disables fcs verification 4 autorx r/w 0 auto receive lapd message this bit configures the receive hdlc controller block #3 to discard any incoming bos or lapd message frame that exactly match which is currently stored in the receive hdlc3 buffer. 0 = disables this ?auto discard? feature 1 = enables this ?auto discard? feature. 3 tx_abort r/w 0 transmit abort this bit configures the transmit hdlc controller block #3 to transmit an abort sequence (string of 7 or more consecutive 1?s) to the remote termi - nal. 0 - configures the transmit hdlc controller block # 3 to function normally (e.g., not transmit the abort sequence). 1 - configures the transmit hdlc controller block # 3 to transmit the abort sequence.
xrt86vx38 79 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 2 tx_idle r/w 0 transmit idle (flag sequence byte) this bit configures the transmit hdlc controller block #3 to unconditionally transmit a repeating string of flag sequence octets (0x7e) in the data link channel to the remote terminal. in normal conditions, the transmit hdlc controller block will repeatedly transm it the flag sequence octet whenever there is no mos message to transmit to the remote terminal equipment. however, if the user invokes this ?transmit idle sequence? feature, then the transmit hdlc controller block will unconditionally transmit a repeat - ing stream of the flag sequence oc tet (thereby overwriting all outbound mos data-link messages). 0 - configures the transmit hdlc controller block # 3 to transmit data-link information in a ?normal? manner. 1 - configures the transmit hdlc controller block # 3 to transmit a repeat - ing string of flag sequence octets (0x7e). n ote : this bit is ignored if the transmit hdlc3 controller is operating in the bos mode - bit 0 (mos/bos) within this register is set to 0. 1 tx_fcs_en r/w 0 transmit lapd message with frame check sequence (fcs) this bit permits the user to configur e the transmit hdlc controller block # 3 to compute and append fcs octets to the ?back-end? of each outbound mos data-link message. 0 - configures the transmit hdlc controller block # 3 to not compute and append the fcs octets to the back-end of each outbound mos data-link message. 1 - configures the transmit hdlc controller block # 3 to compute and append the fcs octets to the back-end of each outbound mos data-link message. n ote : this bit is ignored if the transmit hdlc3 controller has been configured to operate in the bos mode - bit 0 (mos/ bos) within this register is set to 0. 0 mos/ bos r/w 0 message oriented signaling/bit oriented signaling send this bit permits the user to enable lapd transmission through hdlc con - troller block # 3 using either bos (bit-oriented signaling) or mos (mes - sage-oriented signaling) frames. 0 - transmit hdlc controller block # 3 bos message send. 1 - transmit hdlc controller block # 3 mos message send. n ote : this is not an enable bit. this bit must be set to "0" each time a bos is to be sent. t able 66: d ata l ink c ontrol r egister (dlcr3) h ex a ddress : 0 x n153 b it f unction t ype d efault d escription -o peration
xrt86vx38 80 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 67: t ransmit d ata l ink b yte c ount r egister (tdlbcr3) h ex a ddress : 0 x n154 b it f unction t ype d efault d escription -o peration 7 txhdlc3 bufavail/ bufsel r/w 0 transmit hdlc3 buffer available/buffer select this bit has different functions, depending upon whether the user is writing to or reading from this register, as depicted below. if the user is writing data into this register bit: 0 - configures the transmit hdlc3 controller to read out and trans - mit the data, residing within ?transmit hdlc3 buffer # 0", via the data link channel to the remote terminal equipment. 1 - configures the transmit hdlc3 controller to read out and trans - mit the data, residing within the ?transmit hdlc3 buffer #1?, via the data link channel to the remote terminal equipment. if the user is reading data from this register bit: 0 - indicates that ?transmit hdlc3 buffer # 0" is the next available buffer. in this case, if the user wishes to write in the contents of a new ?outbound? data link message into the transmit hdlc3 mes - sage buffer, he/she should proceed to write this message into ?transmit hdlc3 buffer # 0" - address location: 0xn600. 1 - indicates that ?transmit hdlc3 buffer # 1" is the next available buffer. in this case, if the user wishes to write in the contents of a new ?outbound? data link message into the transmit hdlc3 mes - sage buffer, he/she should proceed to write this message into ?transmit hdlc3 buffer # 1" - address location: 0xn700. n ote : if one of these transmit hdlc3 buffers contain a message which has yet to be completely read-in and processed for transmission by the transmit hdlc3 controller, then this bit will automatically reflect the value corresponding to the next available buffer when it is read. changing this bit to the in- use buffer is not permitted. 6-0 tdlbc[6:0] r/w 0000000 transmit hdlc3 message - byte count the exact function of these bits depends on whether the transmit hdlc 3 controller is configured to transmit mos or bos messages to the remote terminal equipment. in bos mode: these bit fields contain the number of repetitions the bos message must be transmitted before the transmit hdlc3 controller gener - ates the transmit end of transfer (txeot) interrupt and halts trans - mission. if these fields are set to 00000000, then the bos message will be transmitted for an indefinite number of times. in mos mode: these bit fields contain the length, in number of octets, of the mes - sage to be transmitted. the l ength of mos message specified in these bits include header bytes such as the sapi, tei, control field, however, it does not include the fcs bytes.
xrt86vx38 81 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 68: r eceive d ata l ink b yte c ount r egister (rdlbcr3) h ex a ddress : 0 x n155 b it f unction t ype d efault d escription -o peration 7 rbufptr r/w 0 receive hdlc2 buffer-pointer this bit identifies which receive hdlc3 buffer contains the most recently received hdlc3 message. 0 - indicates that receive hdlc3 buffer # 0 contains the contents of the most recently received hdlc message. 1 - indicates that receive hdlc3 buffer # 1 contains the contents of the most recently received hdlc message. 6-0 rdlbc[6:0] r/w 0000000 receive hdlc message - byte count the exact function of these bits depends on whether the receive hdlc controller block #3 is configured to receive mos or bos messages. in bos mode: these seven bits contain the num ber of repetitions the bos mes - sage must be received before the receive hdlc3 controller gener - ates the receive end of transfer (rxeot) interrupt. if these bits are set to ?0000000?, the message will be received indefinitely and no receive end of transfer (rxeot) interrupt will be generated. in mos mode: these seven bits contain the size in bytes of the hdlc3 message that has been received and writte n into the receive hdlc buffer. the length of mos message shown in these bits include header bytes such as the sapi, tei, control field, and the fcs bytes.
xrt86vx38 82 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 69: l oopback c ode c ontrol r egister - c ode 7 (lccr7) h ex a ddress : 0 x n156 b it f unction t ype d efault d escription -o peration 7-6 rxlbcalen[1:0] r/w 00 receive loopback code activation length this bit determines the receive loopback code activation length. there are four lengths supported as presented in the table below: 5-4 rxlbcdlen[1:0] r/w 00 receive loopback code deactivation length this bit determines the receive loopback code deactivation length. there are four lengths supported as presented in the table below 3-2 reserved r/w 00 reserved 1 framed r/w 0 framed loopback code this bit selects either framed or unframed loopback code generation in the transmit path. 0 = selects an ?unframed? loopback code for transmission. 1 = selects a ?framed? loopback code for transmission. 0 reserved r/w 0 reserved rxlbcalen[1:0] r eceive l oopback c ode a ctivation l ength 00 selects 4-bit receive loopback code activa- tion sequence 01 selects 5-bit receive loopback code activa- tion sequence 10 selects 6-bit receive loopback code activa- tion sequence 11 selects 7-bit receive loopback code activa- tion sequence rxlbcdlen[1:0] r eceive l oopback c ode d eactivation l ength 00 selects 4-bit receive loopback code deacti- vation sequence 01 selects 5-bit receive loopback code deacti- vation sequence 10 selects 6-bit receive loopback code deacti- vation sequence 11 selects 7-bit receive loopback code deacti- vation sequence
xrt86vx38 83 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 70: r eceive l oopback a ctivation c ode r egister - c ode 7 (rlacr7) h ex a ddress : 0 x n157 b it f unction t ype d efault d escription -o peration 7-1 rxlbac[6:0] r/w 1010101 receive activation loopback code these seven bits determine the receive loopback activation code. the msb of the receive activation loopback code is received first. 0 rxlbacenb r/w 0 receive activation loopback code enable this bit enables the receive loopback activation code detection. receive loopback activation co de is detected by writing the expected receive activation loopback code in this register and enabling it using this bit. the length and format of the receive loopback activation code is determined by the loopback code control register. 0 = disables the receive loopback code activation detection. 1 = enables the receive loopback code activation detection. t able 71: r eceive l oopback d eactivation c ode r egister - c ode 7 (rldcr7) h ex a ddress : 0 x n158 b it f unction t ype d efault d escription -o peration 7-1 rxlbdc[6:0] r/w 1010101 receive deactivation loopback code these seven bits determine the receive loopback deactivation code. the msb of the receive deactivation loopback code is received first. 0 rxlbdcenb r/w 0 receive deactivation loopback code enable this bit enables the receive loopback deactivation code detection. receive loopback deactivation code is detected by writing the expected receive deactivation loopback code in this register and enabling it using this bit. the length and format of the receive loopback deactivation code is determined by the loopback code control register. 0 = disables the receive loopback code deactivation detection. 1 = enables the receive loopback code deactivation detection.
xrt86vx38 84 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description bert pattern definitions 3 in 24 0001 0001 0000 0001 0000 0000 ... 1 in 8 0000 0010 ... 55 octet (unframed) this pattern is shown in hex fo rmat for simplification purposes. 01 01 01 01 01 01 80 01 01 01 01 01 01 03 01 01 01 01 07 01 01 01 01 55 55 55 55 aa aa aa aa 01 01 01 01 01 01 ff ff ff ff ff ff 80 01 80 01 80 01 80 01 80 01 80 01 ... daly pattern (framed) this pattern is shown in hex fo rmat for simplification purposes. 01 01 01 01 01 01 80 01 01 01 01 01 01 03 01 01 01 01 07 01 01 01 01 55 55 55 55 aa aa aa aa 01 01 01 01 01 01 ff ff ff ff ff ff 80 01 80 01 80 01 80 01 80 01 80 01 ... t able 72: bert c ontrol r egister (bcr) h ex a ddress : 0 x n163 b it f unction t ype d efault d escription -o peration 7-4 reserved r/w 0 reserved 3-0 bert[3:0] r/w 0000 bert pattern select 0010 =prbs x20 + x3 + 1 0011 = qrss x20 + x17 + 1 0100 = all ones 0101 = all zeros 0110 = 3 in 24 0111 = 1 in 8 1000 = 55 octet pattern 1001 = daly pattern 1010 = prbs x20 + x17 + 1 others = invalid
xrt86vx38 85 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 1.1 t1 synchronization status message t1 synchronization messages are sent through the fdl (facility data li nk) bits by using a boc (bit oriented code) controller within the xrt86vx38 device. the most ri ght bit position in the boc code is sent first. the ssm message that are used in typical bits applicatio ns are shown below. these messages are defined in specification ansi t1.101-1999. 1.2 t1 boc receiver if enabled, the t1 bo c receiver will monitor the fdl bits for ssm messages with vari ous features being supported. some of these features are change of stat us alarm, 3 independent pre-set codes for matching validation (each having its own alarm), filter settings for consecutive pattern qualification, and many more. n ote : if the receive boc is enabled. the part will still report bos and mos messa ges as described in the register descriptions. 1.3 t1 boc transmitter the t1 boc transmitter will automatica lly insert an ssm message in the co rrect fdl bit positions if enabled. once the message is stored in the tfdl register, bit 0=1 sends the mess age, automatically followed by the abort sequence. t able 73: t1 ssm m essages q uality l evel d escription boc c ode 1 stratum 1 traceable 00000100 11111111 2 synchronized traceability unknown 00001000 11111111 3 stratum 2 traceable 00001100 11 111111 4 stratum 3 traceable 00010000 11111111 5 sonet minimum clock traceable 00100010 11111111 6 stratum 4 traceable 00101000 11111111 7 do not use for synchronization 00110000 11 111111 user assignable reserved for network synchronization use 01000000 11111111
xrt86vx38 86 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description bit 7 - transmit abort sequence enable by default, the transmitter will send an idle flag after the ssm message (unless continous is set). to send an abort sequence to over write the idle flag, set this bit to ?1?. } 0 - disabled } 1 - enable txabort bits [6:5] - receive match filter bits these bits are used to set the number of consecutive error fr ee patterns that must be re ceived before the receive match event is set. this filter can be set to any message, not just a valid ssm message. this filter does not apply to the rfdl valid message or alarm indication. the rfdl alarm and va lid register have their own filter. see bits [2:1] of this register. } 00 - none } 01 - 3 consecutive patterns } 10 - 5 consecutive patterns } 11 - 7 consecutive patterns bit 4 - receive boc enable this bit is used to enable the boc receiver. if this bit is set to "0", only standard bos messages will be processed by the hdlc controller. for clarification, boc messa ges can only be processed through the fdl bits. } 0 - disabled } 1 - enable receive boc bit 3 - boc reset this bit is used to reset the receive boc co ntroller. the function of this bit is to reset all the boc register values to their default values, except the boc in terrupt registers. this register bit is automa tically set back to ?0? so that the user only needs to write ?1? to send a subsequent reset. } 1 - reset boc bits [2:1] - recei ve boc filter bits these bits are used to set the number of consecutive error fr ee patterns that must be received before the receive boc alarm indication is set and the rfdl valid register is updat ed. this filter does not apply to the rfdl matching event registers. the 3 rfdl matching event registers have a se parate filter that applies e qually to all three matching registers. therefore, ther e are a total of 2 filters. } 00 - none } 01 - 3 consecutive patterns } 10 - 5 consecutive patterns } 11 - 7 consecutive patterns bit 0 - send boc message this bit is used to transmit the stored boc message in the tran smit fdl register. this regist er bit is automatically set back to ?0? so that the user only needs to write ?1? to send a subsequent boc message. } 0 - normal operation } 1 - send boc message t able 74: ssm boc c ontrol r egister (boccr 0 x n170 h ) bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 txabort rmf[1:0] rboce bocr rbf[1:0] sboc r/w r/w r/w r/w auto clear r/w r/w auto clear 0 0 0 0 0 0 0 0
xrt86vx38 87 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 bits [7:6] - reserved bits [5:0] - receive boc message these bits contain the most recently received boc message if the filter setting has been meet in bits[2:1] of register 0xn170h. t able 75: ssm r eceive fdl r egister (rfdlr 0 x n171 h ) bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 reserved rboc[5:0] ro ro ro ro ro ro ro ro 0 0 0 0 0 0 0 0
xrt86vx38 88 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description bits [7:6] - reserved bits [5:0] - receive fdl match 1 these bits can be used to set an expected value to be comp ared to the actual receive fdl message. this register is one of three possible expected values that can be set. upon a match of this register, an independent alarm will be set. in addition, this register has a f ilter for consecutive message validation. bits [7:6] - reserved bits [5:0] - receive fdl match 2 these bits can be used to set an expected value to be comp ared to the actual receive fdl message. this register is one of three possible expected values that can be set. upon a match of this register, an independent alarm will be set. in addition, this register has a f ilter for consecutive message validation. bits [7:6] - reserved bits [5:0] - receive fdl match 3 these bits can be used to set an expected value to be comp ared to the actual receive fdl message. this register is one of three possible expected values that can be set. upon a match of this register, an independent alarm will be set. in addition, this register has a f ilter for consecutive message validation. t able 76: ssm r eceive fdl m atch 1 r egister (rfdlmr1 0 x n172 h ) bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 reserved rfdlm1[5:0] r/w r/w r/w r/w r/w r/w r/w r/w 0 0 0 0 0 0 0 0 t able 77: ssm r eceive fdl m atch 2 r egister (rfdlmr2 0 x n173 h ) bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 reserved rfdlm2[5:0] r/w r/w r/w r/w r/w r/w r/w r/w 0 0 0 0 0 0 0 0 t able 78: ssm r eceive fdl m atch 3 r egister (rfdlmr3 0 x n174 h ) bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 reserved rfdlm3[5:0] r/w r/w r/w r/w r/w r/w r/w r/w 0 0 0 0 0 0 0 0
xrt86vx38 89 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 bits [7:6] - reserved bits [5:0] - transmit boc message these bits are used to store the boc message to be trans mitted out the fdl bits. once the message has been stored in this register, bit 0 within the boc control regist er is used to automatically transmit the message. n ote : the txbyte count register 0xn176h is used to set the number of repetitions for th is boc message before the abort sequence is sent out. the default is one repetition. bits [7:0] - transmit byte count value these bits are used to store the amou nt of repetitions the transmit boc message will be sent before an abort sequence. the default value is "1". if "0" is programmed into this register, the transmit bo c will be set continuously. to stop a continuous transmission, the txbyte count should be progammed to a definite value, and then re-send the boc message. t able 79: ssm t ransmit fdl r egister (tfdlr 0 x n175 h ) bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 reserved tboc[5:0] rw rw rw rw rw rw rw rw 0 0 0 0 0 0 0 0 t able 80: ssm t ransmit b yte c ount r egister (tbcr 0 x n176 h ) bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 tbcr[7:0] rw rw rw rw rw rw rw rw 0 0 0 0 0 0 0 1
xrt86vx38 90 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 81: r eceive ds-0 m onitor r egisters ( r d s 0 m r ) h ex a ddress : 0 x n160 to 0 x n16f ( not including 0 x n163) and 0 x n1c0 to 0 x n1d0 b it f unction t ype d efault d escription -o peration 7-0 rxds-0[7:0] ro 00000000 receive ds-0 monitor the contents of these registers will di splay a direct copy of the value currently being processed by the receive framer within the selected time slot. this value will reflect the data present at rtip/rring before any conditioning occurs. ts0 = 0xn160 ts1 = 0xn161 ts2 = 0xn162 ts3 = 0xn164 (note: 0xn163 is not used) ts4 = 0xn165 ts5 = 0xn166 ts6 = 0xn167 ts7 = 0xn168 ts8 = 0xn169 ts9 = 0xn16a ts10 = 0xn16b ts11 = 0xn16c ts12 = 0xn16d ts13 = 0xn16e ts14 = 0xn16f ts15 = 0xn1c0 ts16 = 0xn1c1 ts17 = 0xn1c2 ts18 = 0xn1c3 ts29 = 0xn1c4 ts20 = 0xn1c5 ts21 = 0xn1c6 ts22 = 0xn1c7 ts23= 0xn1c8 n ote : 0xn1c9 to 0xn1d0 are not used in t1 t able 82: t ransmit ds-0 m onitor r egisters (tds0mr) h ex a ddress : 0 x n1d1 to 0 x n1f0 b it f unction t ype d efault d escription -o peration 7-0 txds-0[7:0] ro 00000000 transmit ds-0 monitor the contents of these registers will di splay a direct copy of the value currently being processed by the transmit framer within the selected time slot. this value will reflect the data present at txser before any conditioning occurs. for time slot 0, read register 0xn1d1, for time slot 1, read 0xn1d2, etc. up to time slot 23 which is 0xn1e8. for t1 mode, time slots 24 through 31 are not used.
xrt86vx38 91 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 83: d evice id r egister (devid) h ex a ddress : 0 x 01fe b it f unction t ype d efault d escription -o peration 7-0 devid[7:0] ro 0x3c devid this register is used to identi fy the xrt86vx38 framer/liu. the value of this register is 0x3ch. t able 84: r evision id r egister (revid) h ex a ddress : 0 x 01ff b it f unction t ype d efault d escription -o peration 7-0 revid[7:0] ro 00000001 revid this register is used to identify the revision number of the xrt86vx38. the value of this register for the first revision is a - 0x01h. n ote : the content of this register is subject to change when a newer revision of the device is issued.
xrt86vx38 92 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 85: t ransmit c hannel c ontrol r egister 0-23 (tccr 0-23) h ex a ddress : 0 x n300 to 0 x n317 b it f unction t ype d efault d escription -o peration 7 lapdcntl[1] r/w 1 transmit lapd control these bits select which one of the thre e transmit lapd controller is config - ured to use d/e time slot (octets 0-23) for transmitting lapd messages. the following table presents the diff erent settings of these two bits . n ote : all three transmit lapd controllers can use d/e timeslots for transmission. however, only transmit lapd controller 1 can use datalink for transmission. register 0xn300 represents d/e time slot 0, and 0xn317 represents d/e time slot 23. 6 lapdcntl[0] r/w 0 5 - 4 txzero[1:0] r/w 00 selects type of zero suppression these bits select the type of zero code suppression used by the xrt86vx38 device . lapdcntl[1:0] lapd c ontroller s elected 00 transmit lapd controller 1 01 transmit lapd controller 2 10 the txde[1:0] bits in the transmit signaling and data link select register (tsdlsr - register address - 0xn10a, bit 3-2) determine the data source for d/e time slots. 11 transmit lapd controller 3 t x zero[1:0] t ype of z ero c ode s uppression s elected 00 no zero code suppression is used 01 at&t bit 7 stuffing is used 10 gte zero code suppression is used. if gte zero code suppression is used, bit 8 is stuffed in non-sig- naling frame. otherwise, bit 7 is stuffed in signaling frame if signaling bit is zero. 11 dds zero code suppression is used. the value 0x98 replaces the input data
xrt86vx38 93 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 3-0 txcond(3:0) r/w 0000 transmit channel conditioning for timeslot 0 to 23 these bits allow the user to substitute the input pcm data (octets 0-23) with internally generated conditioning codes prior to transmission to the remote terminal equipment on a per-channel basis. the table below pre - sents the different conditioning codes based on the setting of these bits. register address 0xn300 represents ti me slot 0, and address 0xn317 rep - resents time slot 23. t able 85: t ransmit c hannel c ontrol r egister 0-23 (tccr 0-23) h ex a ddress : 0 x n300 to 0 x n317 b it f unction t ype d efault d escription -o peration t x c ond [1:0] c onditioning c odes 0xn / 0xe contents of timeslot octet are unchanged. 0x1 all 8 bits of the selected timeslot octet are inverted (1?s complement) output = (time_sl ot_octet) xor 0xff 0x2 even bits of the selected timeslot octet are inverted output = (time_sl ot_octet) xor 0xaa 0x3 odd bits of the selected time slot octet are inverted output = (time_sl ot_octet) xor 0x55 0x4 contents of the selected time slot octet will be substituted with the 8 -bit value in the transmit programmable user code register (0xn320-0xn337), 0x5 contents of the timeslot oc tet will be substituted with the value 0x7f (busy code) 0x6 contents of the timeslot oc tet will be substituted with the value 0xff (vacant code) 0x7 contents of the timeslot oc tet will be substituted with the busy time slot code (111#_####), where ##### is the timeslot number 0x8 contents of the timeslot oc tet will be substituted with the moof code (0x1a) 0x9 contents of the timeslot oc tet will be substituted with the a-law digital milliwatt pattern 0xa contents of the timeslot oc tet will be substituted with the ? -law digital milliwatt pattern 0xb the msb (bit 1) of input data is inverted 0xc all input data except msb is inverted 0xd contents of the timeslot oc tet will be substituted with the prbs x 15 + x 14 + 1/qrts pattern n ote : prbs x 15 + x 14 + 1 or qrts pattern depends on prbstype selected in the register 0xn123 - bit 7 0xf d/e time slot - the txde[2:0] bits in the transmit signal- ing and data link select register (0xn10a) will determine the data source for d/e time slots.
xrt86vx38 94 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 86: t ransmit u ser c ode r egister 0-23 (tucr 0-23) h ex a ddress : 0 x n320 to 0 x n337 b it f unction t ype d efault d escription -o peration 7-0 tucr[7:0] r/w b00010111 transmit programmable user code. these eight bits allow users to program any code in this register to replace the input pcm data when the transmit channel control register (tccr) is configured to replace timeslot octet with pro - grammable user code. (i.e. if tccr is set to ?0x4?) the default value of this register is an idle code (b00010111).
xrt86vx38 95 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 87: t ransmit s ignaling c ontrol r egister 0-23 (tscr 0-23) h ex a ddress : 0 x n340 to 0 x n357 b it f unction t ype d efault d escription -o peration 7 a (x) r/w see note transmit signaling bit a this bit allows user to provide signaling bit a (octets 0-23) if robbed-bit signaling is enabled (rob_enb bit of this register set to 1) and if signalling data is inserted from tscr (txsigsrc[1:0] = 01 in this register). n ote : register 0xn340 represents signaling data for time slot 0, and 0xn357 represents signaling data for time slot 23. 6 b (y) r/w see note transmit signaling bit b this bit allows user to provide signaling bit b (octets 0-23) if robbed-bit signaling is enabled (rob_enb bit of this register set to 1) and if signalling data is inserted from tscr (txsigsrc[1:0] = 01 in this register). n ote : register 0xn340 represents signaling data for time slot 0, and 0xn357 represents signaling data for time slot 23. 5 c (x) r/w see note transmit signaling bit c this bit allows user to provide signaling bit c (octets 0-23) if robbed-bit signaling is enabled (rob_enb bit of this register set to 1) and if signalling data is inserted from tscr (txsigsrc[1:0] = 01 in this register). n ote : register 0xn340 represents signaling data for time slot 0, and 0xn357 represents signaling data for time slot 23. 4 d (x) r/w see note transmit signaling bit d this bit allows user to provide signaling bit d (octets 0-23) if robbed-bit signaling is enabled (rob_enb bit of this register set to 1) and if signalling data is inserted from tscr (txsigsrc[1:0] = 01 in this register). n ote : register 0xn340 represents signaling data for time slot 0, and 0xn357 represents signaling data for time slot 23. 3 reserved - see note reserved 2 rob_enb r/w see note robbed-bit signaling enable this bit enables or disables robbed-bit signaling transmission. if robbed-bit signaling is enabled, signaling data is conveyed in the 8th position of each signaling channel by replacing the original lsb of the voice channel with signaling data. 0 = disables robbed-bit signaling. 1 = enables robbed-bit signaling.
xrt86vx38 96 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description n ote : the default value for register address 0xn340 = 0xn1, 0xn341-0xn34f = 0xd0, 0xn350 = 0xb3, 0xn351-0xn35f = 0xd0 1 txsigsrc[1] r/w see note channel signaling control these bits determine the source for signaling information, see table below . 0 txsigsrc[0] r/w see note t able 87: t ransmit s ignaling c ontrol r egister 0-23 (tscr 0-23) h ex a ddress : 0 x n340 to 0 x n357 b it f unction t ype d efault d escription -o peration t x sigsrc[1:0] s ignaling source selected 00/11 signaling data is inserted from input pcm data (txsern pin) 01 signaling data is inserted from this register (tscrs). 10 signaling data is inserted from the transmit signaling input pin (txsig_n) if the transmit signaling interface bit is enabled (i.e. txfr1544 bit = 1 in the transmit interface control register (ticr) register 0xn120),
xrt86vx38 97 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 88: r eceive c hannel c ontrol r egister 0-23 (rccr 0-23) h ex a ddress : 0 x n360 to 0 x n377 b it f unction t ype d efault d escription -o peration 7 lapdcntl[1] r/w 1 receive lapd control these bits select which one of the three receive lapd controller will be configured to use d/e ti me slot (octets 0-23) for receiving lapd messages . n ote : all three lapd controller can use d/e timeslots for receiving lapd messages. however, only lapd controller 1 can use datalink for reception. n ote : register 0xn360 represents d/e time slot 0, and 0xn377 represents d/e time slot 23. 6 lapdcntl[0] r/w 0 5-4 rxzero[1:0] r/w 00 type of zero suppression these bits select the type of zero code suppression used by the xrt86vx38 device. lapdcntl[1:0] r eceive lapd c ontroller s elected 00 receive lapd controller 1 01 receive lapd controller 2 10 the rxde[1:0] bits in the receive signaling and data link select register (rsdlsr - address - 0xn10c) determine the data source for receive d/e time slots. 11 receive lapd controller 3 r x zero[1:0] t ype of z ero c ode s uppression s elected 00 no zero code suppression is used 01 at&t bit 7 stuffing is used 10 gte zero code suppression is used. if gte zero code suppression is used, bit 8 is stuffed in non-signaling frame. otherwise, bit 7 is stuffed in signaling frame if signaling bit is zero. 11 dds zero code suppression is used. the value 0x98 replaces the input data
xrt86vx38 98 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description 3-0 rxcond[3:0] r/w 0000 receive channel conditioning for timeslot 0 to 23 these bits allow the user to substitute the input line data (octets 0-23) with internally generated conditioning codes prior to transmission to the back - plane interface on a per-channel basis. the table below presents the differ - ent conditioning codes based on the setting of these bits. n ote : register address 0xn300 represents time slot 0, and address 0xn317 represents time slot 23. t able 88: r eceive c hannel c ontrol r egister 0-23 (rccr 0-23) h ex a ddress : 0 x n360 to 0 x n377 b it f unction t ype d efault d escription -o peration r x c ond [1:0] c onditioning c odes 0xn / 0xe contents of timeslot octet are unchanged. 0x1 all 8 bits of the selected timeslot octet are inverted (1?s complement) output = (time_slot_octet) xor 0xff 0x2 even bits of the selected timeslot octet are inverted output = (time_slot_octet) xor 0xaa 0x3 odd bits of the selected time slot octet are inverted output = (time_slot_octet) xor 0x55 0x4 contents of the selected timeslot octet will be substituted with the 8 -bit value in the receive programmable user code register (0xn380-0xn397), 0x5 contents of the timeslot octet will be substituted with the value 0x7f (busy code) 0x6 contents of the timeslot octet will be substituted with the value 0xff (vacant code) 0x7 contents of the timeslot octet will be substituted with the busy time slot code (111#_####), where ##### is the timeslot number 0x8 contents of the timeslot octet will be substituted with the moof code (0x1a) 0x9 contents of the timeslot octet will be substituted with the a-law digital milliwatt pattern 0xa contents of the timeslot octet will be substituted with the ? -law digital milliwatt pattern 0xb the msb (bit 1) of input data is inverted 0xc all input data except msb is inverted 0xd contents of the timeslot octet will be substituted with the prbs x 15 + x 14 + 1/qrts pattern n ote : prbs x 15 + x 14 + 1 or qrts pattern depends on prbstype selected in the register 0xn123 - bit 7 0xf d/e time slot - the rxde[2:0] bits in the transmit signal- ing and data link select register (0xn10c) will determine the data source for receive d/e time slots.
xrt86vx38 99 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 89: r eceive u ser c ode r egister 0-23 (rucr 0-23) h ex a ddress : 0 x n380 to 0 x n397 b it f unction t ype d efault d escription -o peration 7-0 rxuser[7:0] r/w 11111111 receive programmable user code. these eight bits allow users to program any code in this register to replace the received data when the receive channel control regis - ter (rccr) is configured to replac e timeslot octet with the receive programmable user code. (i.e. if rccr is set to ?0x4?)
xrt86vx38 100 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 90: r eceive s ignaling c ontrol r egister 0-23 (rscr 0-23) h ex a ddress : 0 x n3a0 to 0 x n3b7 b it f unction t ype d efault d escription -o peration 6 sigc_enb r/w 0 signaling substitution enable this bit enables or disables signaling substitution on the receive side. once signaling substitution is enabled, received signaling bits abcd will be substituted with the abcd values in the receive sub - stitution signaling register (rssr). signaling substitution only occurs in the output pcm data (rxsern). receive signaling array register (rsar - address 0xn500-0xn51f) and the external signaling bus (rxsig_n) output pin will not be affected. 0 = disables signaling substitution on the receive side. 1 = enables signaling substitution on the receive side. 5 oh_enb r/w 0 signaling oh interface output enable this bit enables or disables signaling information to output via the receive overhead pin (rxoh_n). the signaling information in the receive signaling array registers (rsar - address 0xn500-0xn51f) is output to the receive overhead output pin (rxoh_n) if this bit is enabled. 0 = disables signaling information to output via rxoh_n. 1 = enables signaling information to output via rxoh_n. 4 deb_enb r/w 0 per-channel debounce enable this bit enables or disables the signaling debounce feature. when this feature is enabled, the per-channel signaling state must be in the same state for 2 superframes before the receive framer updates signaling information on the receive signaling array regis - ter (rsar) and the signaling pin (rxsign). if the signaling bits for two consecutive superframes are not the same, the current state of rsar and rxsig will not change. when this feature is disabled, r sar and rxsig will be updated as soon as the receive signaling bits have changed. 0 = disables the signaling debounce feature. 1 = enables the signaling debounce feature.
xrt86vx38 101 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 3-2 rxsigc[1:0]] r/w 00 signaling conditioning [1:0] these bits allow user to select the format of signaling substitution on a per-channel basis, as presented in the table below . 1-0 rxsige[1:0] r/w 00 receive signaling extraction [1:0] these bits control per-channel signal ing extraction as presented in the table below. signaling information can be extracted to the receive signaling array register (rsar), the receive signaling output pin (rxsig_n) if the rece ive signaling interface is enable, or the receive overhead interface output (rxoh_n) if oh_enb bit is enabled. (bit 5 of this register). t able 90: r eceive s ignaling c ontrol r egister 0-23 (rscr 0-23) h ex a ddress : 0 x n3a0 to 0 x n3b7 b it f unction t ype d efault d escription -o peration r x sigc[1:0] s ignaling s ubstitution s chemes 00 substitutes all signaling bits with one. 01 enables 16-code (a,b,c,d) signaling substi- tution. users must write to bits 3-0 in the receive sig- naling substitution register (rssr) to provide the 16-code (a,b,c,d) signaling substitution val- ues. 10 enables 4-code (a,b) si gnaling subs titution. users must write to bits 4-5 in the receive sig- naling substitution register (rssr) to provide the 4-code (a,b) signaling substitution values. 11 enables 2-code (a) si gnaling substitution. users must write to bit 6 in the receive signal- ing substitution register (rssr) to provide the 2-code (a) signaling substitution values. r x sige[1:0] s ignaling e xtraction s chemes 00 no signaling information is extracted. 01 enables 16-code (a,b,c,d) signaling extraction. all signaling bits a,b,c,d will be extracted. 10 enables 4-code (a,b) signaling extraction only signaling bits a,b will be extracted. 11 enables 2-code (a) signaling extraction only signaling bit a will be extracted.
xrt86vx38 102 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 91: r eceive s ubstitution s ignaling r egister 0-23 (rssr 0-23) h ex a ddress : 0 x n3c0 to 0 x n3d7 b it f unction t ype d efault d escription -o peration 7-4 reserved - - reserved 3 sig16-a, 4-a, 2-a r/w 0 16-code/4-code/2-code signaling bit a this bit provides the value of signaling bit a to substitute the receive signaling bit a when 16-code or 4-code or 2-code signaling substitu - tion is enabled. 2 sig16-b, 4-b, 2-a r/w 0 16-code/4-code signaling bit b this bit provides the value of signaling bit b to substitute the receive signaling bit b when 16-code or 4-code signaling substitution is enabled. 1 sig16-c, 4-a, 2-a r/w 0 16-code signaling bit c this bit provides the value of signaling bit c to substitute the receive signaling bit c when 16-code signaling substitution is enabled. 0 sig16-d, 4-b, 2-a r/w 0 16-code signaling bit d this bit provides the value of signaling bit d to substitute the receive signaling bit d when 16-code signaling substitution is enabled.
xrt86vx38 103 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 92: r eceive s ignaling a rray r egister 0 to 23 (rsar 0-23) h ex a ddress : 0 x n500 to 0 x n517 b it f unction t ype d efault d escription -o peration 7-4 reserved - - reserved 3 a ro 0 these read only registers reflect the most recently received sig - naling value (a,b,c,d) associated with timeslot 0 to 31. if signaling debounce feature is enabled, the received signaling state must be the same for 2 superframes before this register is updated. if the signaling bits for two consecutive superframes are not the same, the current value of this register will not be changed. when bit 7 within register 0xn107 is set to ?1?, signaling bits in this register are updated on superframe boundary if the signaling debounce feature is di sabled or if bit 7 within register 0xn107 is set to ?0?, this register is updated as soon as the received signaling bits have changed. n ote : the content of this register only has meaning when robbed- bit signaling is enabled. 2 b ro 0 1 c ro 0 0 d ro 0
xrt86vx38 104 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 93: lapd b uffer 0 c ontrol r egister (lapdbcr0) h ex a ddress : 0 x n600 b it f unction t ype d efault d escription -o peration 7-0 lapd buffer 0 r/w 0 lapd buffer 0 (96-bytes) auto incrementing this register is used to transmit and receive lapd messages within buffer 0 of the hdlc controller. any one of the three hdlc control - ler can be chosen in the lapd select register (0xn11b). users should determine the next available buffer by reading the bufaval bit (bit 7 of the transmit data li nk byte count register 1 (address 0xn114), register 2 (0xn144) and register 3 (0xn154) depending on which hdlc controller is selected. if buffer 0 is available, writing to buffer 0 will insert the message into the outgoing lapd frame after the lapd message is sent and the data from the transmit buffer cannot be retrieved. after detecting the receive end of transfer interrupt (rxeot), users should read the rbufptr bit (bit 7 of the receive data link byte count register 1 (address 0xn115), register 2 (0xn145), or regis - ter 3 (0xn155) depending on which hdlc controller is selected) to determine which buffer contains the received lapd message ready to be read. if rbufptr bit indicates that buffer 0 is available to be read, reading buffer 0 (register 0xn600) continuously will retrieve the entire received lapd message. n ote : when writing to or reading from buffer 0, the register is automatically incremented su ch that the entire 96 byte lapd message can be written into or read from buffer 0 (register 0xn600) continuously. t able 94: lapd b uffer 1 c ontrol r egister (lapdbcr1) h ex a ddress : 0 x n700 b it f unction t ype d efault d escription -o peration 7-0 lapd buffer 1 r/w 0 lapd buffer 1 (96-bytes) auto incrementing this register is used to transmit and receive lapd messages within buffer 1 of the hdlc controller. any one of the three hdlc control - ler can be is chosen in the lapd select register (0xn11b). users should determine the next available buffer by reading the bufaval bit (bit 7 of the transmit data li nk byte count register 1 (address 0xn114), register 2 (0xn144) and register 3 (0xn154) depending on which hdlc controller is selected. if buffer 1 is available, writing to buffer 1 will insert the message into the outgoing lapd frame after the lapd message is sent and the data from the transmit buffer 1 cannot be retrieved. after detecting the receive end of transfer interrupt (rxeot), users should read the rbufptr bit (bit 7 of the receive data link byte count register 1 (address 0xn115), register 2 (0xn145), or regis - ter 3 (0xn155) depending on which hdlc controller is selected) to determine which buffer contains the received lapd message ready to be read. if rbufptr bit indicates that buffer 1 is available to be read, reading buffer 1 (register 0xn700) continuously will retrieve the entire received lapd message. n ote : when writing to or reading from buffer 0, the register is automatically incremented su ch that the entire 96 byte lapd message can be written into or read from buffer 0 (register 0xn600) continuously.
xrt86vx38 105 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 95: pmon r eceive l ine c ode v iolation c ounter msb (rlcvcu) h ex a ddress : 0 x n900 b it f unction t ype d efault d escription -o peration 7 rlcvc[15] rur 0 performance monitor ?receive line code violation? 16-bit counter - upper byte: these reset-upon-read bits, along with that wit hin the pmon receive line code violation counter register lsb combine to reflect the cumulative number of instances that line code violation has been detected by the receive t1 framer block since the last read of this register. this register contains the most sign ificant byte of this 16-bit of the line code violation counter. n ote : for all 16-bit wide pmon registers, user must read the msb counter first before reading the lsb counter in order to read the accurate pmon counts. to clear pmon count, user must read the msb counter first before reading the lsb counter in order to clear the pmon count. 6 rlcvc[14] rur 0 5 rlcvc[13] rur 0 4 rlcvc[12] rur 0 3 rlcvc[11] rur 0 2 rlcvc[10] rur 0 1 rlcvc[9] rur 0 0 rlcvc[8] rur 0 t able 96: pmon r eceive l ine c ode v iolation c ounter lsb (rlcvcl) h ex a ddress : 0 x n901 b it f unction t ype d efault d escription -o peration 7 rlcvc[7] rur 0 performance monitor ?receive line code violation? 16-bit counter - lower byte: these reset-upon-read bits, along with that wit hin the pmon receive line code violation counter register msb combine to reflect the cumulative number of instances that line code violation has been detected by the receive t1 framer block since the last read of this register. this register contains the least sign ificant byte of this 16-bit of the line code violation counter. n ote : for all 16-bit wide pmon registers, user must read the msb counter first before reading the lsb counter in order to read the accurate pmon counts. to clear pmon count, user must read the msb counter first before reading the lsb counter in order to clear the pmon count. 6 rlcvc[6] rur 0 5 rlcvc[5] rur 0 4 rlcvc[4] rur 0 3 rlcvc[3] rur 0 2 rlcvc[2] rur 0 1 rlcvc[1] rur 0 0 rlcvc[0] rur 0
xrt86vx38 106 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description . . t able 97: pmon r eceive f raming a lignment b it e rror c ounter msb (rfaecu) h ex a ddress : 0 x n902 b it f unction t ype d efault d escription -o peration 7 rfaec[15] rur 0 performance monitor ?receive framing alignment error 16-bit counter? - upper byte: these reset-upon-read bits, along with that wit hin the ?pmon receive framing alignment error counter register lsb? combine to reflect the cumulative number of instances that the receive framing alignment errors has been detected by the receive t1 framer block since the last read of this register. this register contains the most sign ificant byte of this 16-bit of the receive framing alignment error counter. n ote : for all 16-bit wide pmon registers, user must read the msb counter first before reading the lsb counter in order to read the accurate pmon counts. to clear pmon count, user must read the msb counter first before reading the lsb counter in order to clear the pmon count. 6 rfaec[14] rur 0 5 rfaec[13] rur 0 4 rfaec[12] rur 0 3 rfaec[11] rur 0 2 rfaec[10] rur 0 1 rfaec[9] rur 0 0 rfaec[8] rur 0 t able 98: pmon r eceive f raming a lignment b it e rror c ounter lsb (rfaecl) h ex a ddress : 0 x n903 b it f unction t ype d efault d escription -o peration 7 rfaec[7] rur 0 performance monitor ?receive framing alignment error 16-bit counter? - lower byte: these reset-upon-read bits, along with that wit hin the ?pmon receive framing alignment error counter register msb? combine to reflect the cumulative number of instances that the receive framing alignment errors has been detected by the receive t1 framer block since the last read of this register. this register contains the least sign ificant byte of this 16-bit of the receive framing alignment error counter. n ote : for all 16-bit wide pmon registers, user must read the msb counter first before reading the lsb counter in order to read the accurate pmon counts. to clear pmon count, user must read the msb counter first before reading the lsb counter in order to clear the pmon count. 6 rfaec[6] rur 0 5 rfaec[5] rur 0 4 rfaec[4] rur 0 3 rfaec[3] rur 0 2 rfaec[2] rur 0 1 rfaec[1] rur 0 0 rfaec[0] rur 0
xrt86vx38 107 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 99: pmon r eceive s everely e rrored f rame c ounter (rsefc) h ex a ddress : 0 x n904 b it f unction t ype d efault d escription -o peration 7 rsefc[7] rur 0 performance monitor - receive severely errored frame counter (8-bit counter) these reset-upon-read bit fields reflect the cumulative number of instances that receive severely errored frames have been detected by the t1 framer since the last read of this register. in t1 mode, severely errored frame is defined as having framing bit errors in contiguous windows. in t1 sf mode, sef is defined if ft bits have been received consecutively in errors for 0.75ms or 6 sf frames. in t1 esf mode, sef is defined if fps bit have been received consecutively in errors for 3 ms or 24 esf frames. 6 rsefc[6] rur 0 5 rsefc[5] rur 0 4 rsefc[4] rur 0 3 rsefc[3] rur 0 2 rsefc[2] rur 0 1 rsefc[1] rur 0 0 rsefc[0] rur 0
xrt86vx38 108 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 100: pmon r eceive crc-6 bit e rror c ounter - msb (rsbbecu) h ex a ddress : 0 x n905 b it f unction t ype d efault d escription -o peration 7 rsbbec[15] rur 0 performance monitor ?receive sync hronization bit error 16-bit counter? - upper byte: these reset-upon-read bits, along with that wit hin the ?pmon receive synchronization bit error counter register lsb? combine to reflect the cumulative number of instances that the receive syn - chronization bit errors has been detected by the receive t1 framer block since the last read of this register. this register contains the most sign ificant byte of this 16-bit of the receive synchronization bit error counter. n ote : for all 16-bit wide pmon registers, user must read the msb counter first before reading the lsb counter in order to read the accurate pmon counts. to clear pmon count, user must read the msb counter first before reading the lsb counter in order to clear the pmon count. 6 rsbbec[14] rur 0 5 rsbbec[13] rur 0 4 rsbbec[12] rur 0 3 rsbbec[11] rur 0 2 rsbbec[10] rur 0 1 rsbbec[9] rur 0 0 rsbbec[8] rur 0 t able 101: pmon r eceive crc-6 b it e rror c ounter - lsb (rsbbecl) h ex a ddress : 0 x n906 b it f unction t ype d efault d escription -o peration 7 rsbbec[7] rur 0 performance monitor ?receive sync hronization bit error 16-bit counter? - lower byte: these reset-upon-read bits, along with that wit hin the ?pmon receive synchronization bit error counter register msb? combine to reflect the cumulative number of instances that the receive syn - chronization bit errors has been detected by the receive t1 framer block since the last read of this register. this register contains the least sign ificant byte of this 16-bit of the receive synchronization bit error counter. n ote : for all 16-bit wide pmon registers, user must read the msb counter first before reading the lsb counter in order to read the accurate pmon counts. to clear pmon count, user must read the msb counter first before reading the lsb counter in order to clear the pmon count. 6 rsbbec[6] rur 0 5 rsbbec[5] rur 0 4 rsbbec[4] rur 0 3 rsbbec[3] rur 0 2 rsbbec[2] rur 0 1 rsbbec[1] rur 0 0 rsbbec[0] rur 0
xrt86vx38 109 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 102: pmon r eceive s lip c ounter (rsc) h ex a ddress : 0 x n909 b it f unction t ype d efault d escription -o peration 7 rsc[7] rur 0 performance monitor - receive slip counter (8 -bit counter) these reset-upon-read bit fields reflect the cumulative number of instances that receive slip events have been detected by the t1 framer since the last read of this register. n ote : a slip event is defined as a replication or deletion of a t1 frame by the receive slip buffer. 6 rsc[6] rur 0 5 rsc[5] rur 0 4 rsc[4] rur 0 3 rsc[3] rur 0 2 rsc[2] rur 0 1 rsc[1] rur 0 0 rsc[0] rur 0 t able 103: pmon r eceive l oss of f rame c ounter (rlfc) h ex a ddress : 0 x n90a b it f unction t ype d efault d escription -o peration 7 rlfc[7] rur 0 performance monitor - receive loss of frame counter (8-bit counter) these reset-upon-read bit fields reflect the cumulative number of instances that receive loss of frame condition have been detected by the t1 framer since the last read of this register. n ote : this counter counts once ev ery time the loss of frame condition is declared. this count er provides the capability to measure an accumulation of short failure events. 6 rlfc[6] rur 0 5 rlfc[5] rur 0 4 rlfc[4] rur 0 3 rlfc[3] rur 0 2 rlfc[2] rur 0 1 rlfc[1] rur 0 0 rlfc[0] rur 0 t able 104: pmon r eceive c hange of f rame a lignment c ounter (rcfac) h ex a ddress : 0 x n90b b it f unction t ype d efault d escription -o peration 7 rcfac[7] rur 0 performance monitor - receive change of frame alignment counter (8-bit counter) these reset-upon-read bit fields reflect the cumulative number of instances that receive change of framing alignment have been detected by the t1 framer since the last read of this register. n ote : change of framing alignment (cofa) is declared when the newly-locked framing pattern is different from the one offered by off-line framer. 6 rcfac[6] rur 0 5 rcfac[5] rur 0 4 rcfac[4] rur 0 3 rcfac[3] rur 0 2 rcfac[2] rur 0 1 rcfac[1] rur 0 0 rcfac[0] rur 0
xrt86vx38 110 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 105: pmon lapd1 f rame c heck s equence e rror c ounter 1 (lfcsec1) h ex a ddress : 0 x n90c b it f unction t ype d efault d escription -o peration 7 fcsec1[7] rur 0 performance monitor - lapd 1 frame check sequence error counter (8-bit counter) these reset-upon-read bit fields reflect the cumulative number of instances that frame check sequence error have been detected by the lapd controller 1 since the last read of this register. 6 fcsec1[6] rur 0 5 fcsec1[5] rur 0 4 fcsec1[4] rur 0 3 fcsec1[3] rur 0 2 fcsec1[2] rur 0 1 fcsec1[1] rur 0 0 fcsec1[0] rur 0 t able 106: prbs b it e rror c ounter msb (pbecu) h ex a ddress : 0 x n90d b it f unction t ype d efault d escription -o peration 7 prbse[15] rur 0 performance monitor - t1 prbs bit error 16-bit counter - upper byte: these reset-upon-read bits, along with that wit hin the ?pmon t1 prbs bit error counter regist er lsb? combine to reflect the cumulative number of instances that the receivet1 prbs bit errors has been detected by the receive t1 framer block since the last read of this register. this register contains the most sign ificant byte of this 16-bit of the receive t1 prbs bit error counter. n ote : for all 16-bit wide pmon registers, user must read the msb counter first before reading the lsb counter in order to read the accurate pmon counts. to clear pmon count, user must read the msb counter first before reading the lsb counter in order to clear the pmon count. 6 prbse[14] rur 0 5 prbse[13] rur 0 4 prbse[12] rur 0 3 prbse[11] rur 0 2 prbse[10] rur 0 1 prbse[9] rur 0 0 prbse[8] rur 0 t able 107: prbs b it e rror c ounter lsb (pbecl) h ex a ddress : 0 x n90e b it f unction t ype d efault d escription -o peration 7 prbse[7] rur 0 performance monitor - t1 prbs bit error 16-bit counter - lower byte: these reset-upon-read bits, along with that wit hin the ?pmon t1 prbs bit error counter register msb? combine to reflect the cumulative number of instances that the receivet1 prbs bit errors has been detected by the receive t1 framer block since the last read of this register. this register contains the least sign ificant byte of this 16-bit of the receive t1 prbs bit error counter. n ote : for all 16-bit wide pmon registers, user must read the msb counter first before reading the lsb counter in order to read the accurate pmon counts. to clear pmon count, user must read the msb counter first before reading the lsb counter in order to clear the pmon count. 6 prbse[6] rur 0 5 prbse[5] rur 0 4 prbse[4] rur 0 3 prbse[3] rur 0 2 prbse[2] rur 0 1 prbse[1] rur 0 0 prbse[0] rur 0
xrt86vx38 111 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 108: t ransmit s lip c ounter (tsc) h ex a ddress : 0 x n90f b it f unction t ype d efault d escription -o peration 7 txslip[7] rur 0 performance monitor - transmit slip counter (8-bit counter) these reset-upon-read bit fields reflect the cumulative number of instances that transmit slip events have been detected by the t1 framer since the last read of this register. n ote : a slip event is defined as a replication or deletion of a t1 frame by the transmit slip buffer. 6 txslip[6] rur 0 5 txslip[5] rur 0 4 txslip[4] rur 0 3 txslip[3] rur 0 2 txslip[2] rur 0 1 txslip[1] rur 0 0 txslip[0] rur 0 t able 109: e xcessive z ero v iolation c ounter msb (ezvcu) h ex a ddress : 0 x n910 b it f unction t ype d efault d escription -o peration 7 ezvc[15] rur 0 performance monitor - t1 excessive zero violation 16-bit counter - upper byte: these reset-upon-read bits, along with that wit hin the ?pmon t1 excessive zero violation counter register lsb? combine to reflect the cumulative number of instances that the receivet1 excessive zero violation has been detected by the receive t1 framer block since the last read of this register. this register contains the most sign ificant byte of this 16-bit of the receive t1 excessive ze ro violation counter. n ote : for all 16-bit wide pmon registers, user must read the msb counter first before reading the lsb counter in order to read the accurate pmon counts. to clear pmon count, user must read the msb counter first before reading the lsb counter in order to clear the pmon count. 6 ezvc[14] rur 0 5 ezvc[13] rur 0 4 ezvc[12] rur 0 3 ezvc[11] rur 0 2 ezvc[10] rur 0 1 ezvc[9] rur 0 0 ezvc[8] rur 0 t able 110: e xcessive z ero v iolation c ounter lsb (ezvcl) h ex a ddress : 0 x n911 b it f unction t ype d efault d escription -o peration 7 ezvc[7] rur 0 performance monitor - t1 excessive zero violation 16-bit counter - lower byte: these reset-upon-read bits, along with that wit hin the ?pmon t1 excessive zero violation counter register msb? combine to reflect the cumulative number of instances that the receivet1 excessive zero violation has been detected by the receive t1 framer block since the last read of this register. this register contains the least sign ificant byte of this 16-bit of the receive t1 excessive ze ro violation counter. n ote : for all 16-bit wide pmon registers, user must read the msb counter first before reading the lsb counter in order to read the accurate pmon counts. to clear pmon count, user must read the msb counter first before reading the lsb counter in order to clear the pmon count. 6 ezvc[6] rur 0 5 ezvc[5] rur 0 4 ezvc[4] rur 0 3 ezvc[3] rur 0 2 ezvc[2] rur 0 1 ezvc[1] rur 0 0 ezvc[0] rur 0
xrt86vx38 112 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 111: pmon lapd2 f rame c heck s equence e rror c ounter 2 (lfcsec2) h ex a ddress : 0 x n91c b it f unction t ype d efault d escription -o peration 7 fcsec2[7] rur 0 performance monitor - lapd 2 frame check sequence error counter (8-bit counter) these reset-upon-read bit fields reflect the cumulative number of instances that frame check sequence error have been detected by the lapd controller 2 since the last read of this register. 6 fcsec2[6] rur 0 5 fcsec2[5] rur 0 4 fcsec2[4] rur 0 3 fcsec2[3] rur 0 2 fcsec2[2] rur 0 1 fcsec2[1] rur 0 0 fcsec2[0] rur 0 t able 112: pmon lapd2 f rame c heck s equence e rror c ounter 3 (lfcsec3) h ex a ddress : 0 x n92c b it f unction t ype d efault d escription -o peration 7 fcsec3[7] rur 0 performance monitor - lapd 3 frame check sequence error counter (8-bit counter) these reset-upon-read bit fields reflect the cumulative number of instances that frame check sequence error have been detected by the lapd controller 3 since the last read of this register. 6 fcsec3[6] rur 0 5 fcsec3[5] rur 0 4 fcsec3[4] rur 0 3 fcsec3[3] rur 0 2 fcsec3[2] rur 0 1 fcsec3[1] rur 0 0 fcsec3[0] rur 0
xrt86vx38 113 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 113: b lock i nterrupt s tatus r egister (bisr) h ex a ddress : 0 x nb00 b it f unction t ype d efault d escription -o peration 7 reserved for e1 mode only 6 lbcode ro 0 loopback code block interrupt status this bit indicates whether or not the loopback code block has an interrupt request awaiting service. 0 - indicates no outstanding loopback code block interrupt request is awaiting service 1 - indicates the loopback code block has an interrupt request awaiting service. interrupt service routine should branch to the inter - rupt source and read the loopback code interrupt status register (address 0xnb0a) to clear the interrupt n ote : this bit will be reset to 0 after the microprocessor has performed a read to the loopback code interrupt status register. 5 rxclklos ro 0 loss of recovered clock interrupt status this bit indicates whether or not the t1 receive framer is currently declaring the "loss of recovered clock" interrupt. 0 = indicates that the t1 receive framer block is not currently declaring the "loss of recovered clock" interrupt. 1 = indicates that the t1 receive framer block is currently declar - ing the "loss of recovered clock" interrupt. n ote : this bit is only active if the clock loss detect ion feature is enabled (register - 0xn100) 4 onesec ro 0 one second interrupt status this bit indicates whether or not the t1 receive framer block is cur - rently declaring the "one second" interrupt. 0 = indicates that the t1 receive framer block is not currently declaring the "one second" interrupt. 1 = indicates that the t1 receive framer block is currently declar - ing the "one second" interrupt. 3 hdlc ro 0 hdlc block interrupt status this bit indicates whether or not the hdlc block has any interrupt request awaiting service. 0 = indicates no outstanding hdlc block interrupt request is await - ing service 1 = indicates hdlc block has an interrupt request awaiting service. interrupt service routine should branch to the interrupt source and read the corresponding data link status registers (address 0xnb06, 0xnb16, 0xnb26, 0xnb10, 0xnb18, 0xnb28) to clear the interrupt. n ote : this bit will be reset to 0 after the microprocessor has performed a read to the corresponding data link status registers that generated the interrupt.
xrt86vx38 114 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description 2 slip ro 0 slip buffer block interrupt status this bit indicates whether or not the slip buffer block has any out - standing interrupt request awaiting service. 0 = indicates no outstanding slip buffer block interrupt request is awaiting service 1 = indicates slip buffer block has an interrupt request awaiting ser - vice. interrupt service routine should branch to the interrupt source and read the slip buffer interrupt status register (address 0xnb08) to clear the interrupt n ote : this bit will be reset to 0 after the microprocessor has performed a read to the slip buffer interrupt status register. 1 alarm ro 0 alarm & error block interrupt status this bit indicates whether or not the alarm & error block has any outstanding interrupt request awaiting service. 0 = indicates no outstanding interrupt request is awaiting service 1 = indicates the alarm & error block has an interrupt request await - ing service. interrupt service rout ine should branch to the interrupt source and read the corresponding alarm and error status registers (address 0xnb02, 0xnb0e, 0xnb40) to clear the interrupt. n ote : this bit will be reset to 0 after the microprocessor has performed a read to the corresponding alarm & error interrupt status register that generated the interrupt. 0 t1 frame ro 0 t1 framer block interrupt status this bit indicates whether or not the t1 framer block has any out - standing interrupt request awaiting service. 0 = indicates no outstanding interrupt request is awaiting service. 1 = indicates the t1 framer block has an interrupt request awaiting service. interrupt service routine should branch to the interrupt source and read the t1 framer st atus register (address 0xnb04) to clear the interrupt n ote : this bit will be reset to 0 after the microprocessor has performed a read to the t1 fram er interrupt status register. t able 113: b lock i nterrupt s tatus r egister (bisr) h ex a ddress : 0 x nb00 b it f unction t ype d efault d escription -o peration
xrt86vx38 115 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 114: b lock i nterrupt e nable r egister (bier) h ex a ddress : 0 x nb01 b it f unction t ype d efault d escription -o peration 7 reserved for e1 mode only 6 lbcode_enb r/w 0 loopback code block interrupt enable this bit permits the user to either enable or disable the loopback code interrupt block for interrupt generation. writing a ?0? to this register bit will disable the loopback code block for interrupt generation, all loopback code interrupts will be dis - abled for interrupt generation. if the user writes a ?1? to this register bit, the loopback code inter - rupts at the ?block level? will be enabled. however, the individual loopback code interrupts at the ?source level? still need to be enabled to in order to generate that particular interrupt to the inter - rupt pin. 0 - disables all loopback code interrupt block interrupt within the device. 1 - enables the loopback code interrupt at the ?block-level?. 5 rxclkloss r/w 0 loss of recovered clock interrupt enable this bit permits the user to eit her enable or disable the loss of recovered clock interrupt for interrupt generation. 0 - disables the loss of recovered clock interrupt within the device. 1 - enables the loss of recovered clock interrupt at the ?source- level?. 4 onesec_enb r/w 0 one second interrupt enable this bit permits the user to either enable or disable the one second interrupt for interrupt generation. 0 - disables the one second interrupt within the device. 1 - enables the one second in terrupt at the ?source-level?. 3 hdlc_enb r/w 0 hdlc block interrupt enable this bit permits the user to either enable or disable the hdlc block for interrupt generation. writing a ?0? to this register bit will disable the hdlc block for inter - rupt generation, all hdlc interrupts will be disabled for interrupt generation. if the user writes a ?1? to this regi ster bit, the hdlc block interrupt at the ?block level? will be enabled. however, the individual hdlc interrupts at the ?source level? st ill need to be enabled in order to generate that particular inte rrupt to the interrupt pin. 0 - disables all sa6 block interrupt within the device. 1 - enables the sa6 interrupt at the ?block-level?.
xrt86vx38 116 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description 2 slip_enb r/w 0 slip buffer block interrupt enable this bit permits the user to either enable or disable the slip buffer block for interrupt generation. writing a ?0? to this register bit will disable the slip buffer block for interrupt generation, then all slip buffer interrupts will be disabled for interrupt generation. if the user writes a ?1? to this regi ster bit, the slip buffer block inter - rupt at the ?block level? will be enabled. however, the individual slip buffer interrupts at the ?source level? still need to be enabled in order to generate that particular interrupt to the interrupt pin. 0 - disables all slip buffer block interrupt within the device. 1 - enables the slip buffer interrupt at the ?block-level?. 1 alarm_enb r/w 0 alarm & error block interrupt enable this bit permits the user to either enable or disable the alarm & error block for interrupt generation. writing a ?0? to this register bit will disable the alarm & error block for interrupt generation, then all alarm & error interrupts will be dis - abled for interrupt generation. if the user writes a ?1? to this register bit, the alarm & error block interrupt at the ?block level? will be enabled. however, the individual alarm & error interrupts at the ?s ource level? still need to be enabled in order to generate that part icular interrupt to the interrupt pin. 0 - disables all alarm & error block interrupt within the device. 1 - enables the alarm & error interrupt at the ?block-level?. 0 t1frame_enb r/w 0 t1 framer block enable this bit permits the user to either enable or disable the t1 framer block for interrupt generation. writing a ?0? to this register bit will disable the t1 framer block for interrupt generation, then all t1 framer interrupts will be disabled for interrupt generation. if the user writes a ?1? to this re gister bit, the t1 framer block inter - rupt at the ?block level? will be enabled. however, the individual t1 framer interrupts at the ?source level? still need to be enabled in order to generate that particular interrupt to the interrupt pin. 0 - disables all t1 framer block interrupt within the device. 1 - enables the t1 framer interrupt at the ?block-level?. t able 114: b lock i nterrupt e nable r egister (bier) h ex a ddress : 0 x nb01 b it f unction t ype d efault d escription -o peration
xrt86vx38 117 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 115: a larm & e rror i nterrupt s tatus r egister (aeisr) h ex a ddress : 0 x nb02 b it f unction t ype d efault d escription -o peration 7 rx oof state ro 0 receive out of frame defect state this read-only bit indicates whether or not the receive t1 framer block is currently declaring the ?out of frame? defect condition within the incoming t1 data-stream, as described below. out of frame defect conditi on is declared when ?tolr? out of ?rang? errors in the framing bit pattern is detected. (register 0xn10b) 0 ? the receive t1 framer block is not currently declaring t he ?out of frame? defect condition. 1 ? the receive t1 framer block is currently declaring the ?out of frame? defect condition. 6 rxais state ro 0 receive alarm indication status defect state this read-only bit indicates whether or not the receive t1 framer block is currently declaring the ais defect condit ion within the incoming t1 data-stream, as described below. ais defect is declared when ais condition persists for 42 milliseconds. ais defect is cleared when ais condition is absent for 42 milliseconds. 0 ? the receive t1 framer block is not currently declaring the ais defect con - dition. 1 ? the receive t1 framer block is currently declaring the ais defect condition. 5 rxyel state ro 0 receive yellow alarm state this read-only bit indicates whether or not the receive t1 framer block is currently declaring the yellow alarm c ondition within the incoming t1 data- stream, as described below. yellow alarm or remote alarm indication (rai) is declared when rai condition persists for 900 milliseconds. yellow alarm or rai is cleared immediately when rai condition is absent even if the t1 framer is receiving t1 idle or rai-ci signa - tures in esf mode. 0 ? the receive t1 framer block is no t currently declaring the yellow alarm condition. 1 ? the receive t1 framer block is currently declaring the yellow alarm condi - tion. 4 los_state ro 0 framer receive loss of signal (los) state this read-only bit indicates whether or not the receive t1 framer is currently declaring the loss of signal (los) condition within the incoming t1 data-stream, as described below los defect is declared when los condit ion persists for 175 consecutive bits. los defect is cleared when los condition is absent or when the received signal reaches a 12.5% ones density for 175 consecutive bits. 0 = the receive t1 framer block is not currently declaring the loss of signal (los) condition. 1 = the receive t1 framer block is currently declaring the loss of signal (los) condition. 3 lcv int status rur/ wc 0 line code violation interrupt status . this reset-upon-read bit field indicates whether or not the receive t1 liu block has detected a line code violation interrup t since the last read of this register. 0 = indicates no line code violation have occurred since the last read of this reg - ister. 1 = indicates one or more line code viol ation interrupt has occurred since the last read of this register.
xrt86vx38 118 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description 2 rx oof state change rur/ wc 0 change in receive out of frame defect condition interrupt status . this reset-upon-read bit field indicates whether or not the ?change in receive out of frame defect condition? interrupt has occurred since the last read of this register. out of frame defect conditi on is declared when ?tolr? out of ?rang? errors in the framing bit pattern is detected. (register 0xn10b) if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block declares the out of frame defect condition. 2. whenever the receive t1 framer block clears the out of frame defect condition 0 = indicates that the ?change in receive out of frame defect condition? interrupt has not occurred since the last read of this register 1 = indicates that the ?change in receive out of frame defect condition? interrupt has occurred since the last read of this register 1 rxais state change rur/ wc 0 change in receive ais condition interrupt status . this reset-upon-read bit field indicates whether or not the ?change in receive ais condition? interrupt has occurred si nce the last read of this register. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block declares the ais condition. 2. whenever the receive t1 framer block clears the ais condition 0 = indicates that the ?change in rece ive ais condition? interrupt has not occurred since the last read of this register 1 = indicates that the ?change in receiv e ais condition? interrupt has occurred since the last read of this register 0 rxyel state change rur/ wc 0 change in receive yellow alarm interrupt status. this reset-upon-read bit field indicates whether or not the ?change in receive yellow alarm condition? interrupt has occurred since the last read of this register. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer bl ock declares the yellow alarm condition. 2. whenever the receive t1 framer block clears the yellow alarm condition 0 = indicates that the ?change in receiv e yellow alarm condition? interrupt has not occurred since the last read of this register 1 = indicates that the ?change in receiv e yellow alarm condition? interrupt has occurred since the last read of this register t able 115: a larm & e rror i nterrupt s tatus r egister (aeisr) h ex a ddress : 0 x nb02 b it f unction t ype d efault d escription -o peration
xrt86vx38 119 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 116: a larm & e rror i nterrupt e nable r egister (aeier) h ex a ddress : 0 x nb03 b it f unction t ype d efault d escription -o peration 7-5 reserved - - reserved (e1 mode only) 4 - - - this bit should be set to?0? for proper operation. 3 lcv enb r/w 0 line code violation interrupt enable this bit permits the user to either enable or disable the ?line code viola - tion? interrupt within the xrt86vx38 device. if the user enables this inter - rupt, then the receive t1 framer bloc k will generate an interrupt when line code violation is detected. 0 = disables the interrupt generation when line code violation is detected. 1 = enables the interrupt generation when line code violation is detected. 2 rxoof enb r/w 0 change in out of frame defect condition interrupt enable this bit permits the user to either enable or disable the ?change in out of frame defect condition? interrupt, within the xrt86vx38 device. if the user enables this interrupt, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. the instant that the receive t1 fr amer block declares the out of frame defect condition. 2. the instant that the receive t1 framer block clears the out of frame defect condition. 0 ? disables the ?change in out of frame defect condition? interrupt. 1 ? enables the ?change in out of frame defect condition? interrupt. 1 rxais enb r/w 0 change in ais condition interrupt enable this bit permits the user to either enable or disable the ?change in ais condition? interrupt, within the xrt86vx 38 device. if the user enables this interrupt, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. the instant that the receive t1 framer block declares the ais condition. 2. the instant that the receive t1 framer block clears the ais condition. 0 ? disables the ?change in ais condition? interrupt. 1 ? enables the ?change in ais condition? interrupt. 0 rxyel enb r/w 0 change in yellow alarm condition interrupt enable this bit permits the user to either enable or disable the ?change in yellow alarm condition? interrupt, within the xrt86vx38 device. if the user enables this interrupt, then the receiv e t1 framer block will generate an interrupt in response to either one of the following conditions. 1. the instant that the receive t1 framer block declares the yellow alarm condition. 2. the instant that the receive t1 framer block clears the yellow alarm condition. 0 ? disables the ?change in yellow alarm condition? interrupt. 1 ? enables the ?change in yellow alarm condition? interrupt.
xrt86vx38 120 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 117: f ramer i nterrupt s tatus r egister (fisr) h ex a ddress : 0 x nb04 b it f unction t ype d efault d escription -o peration 7 ds0_change rur 0 change in ds-0 yellow alarm interrupt status this reset-upon-read bit field indicates whether or not the ?change in ds-0 yellow alarm? interrupt has occurred since the last read of this regis - ter. 0 - indicates that the ?change in ds-0 yellow alarm? interrupt has not occurred since the last read of this register. 1 - indicates that the ?change in ds-0 yellow alarm? interrupt has occurred since the last read of this register. n ote : by default, ds-0 yellow alarm is detected on the ingress (rtip/ rring) side. to detect ds-0 yel on the egress (txser) side, the ds-0 switch bit (bit 2) must be set to "1" in register 0xn112. 6 ds0_status ro 0 ds-0 yellow alarm interrupt status this read only bit will indicate the state of the ds-0 yellow alarm detec - tion. when a ds-0 yellow alarm is present, this bit will be pulled "high". when a ds-0 yellow alarm is not present, this bit will remain "low". 0 - ds-0 yellow alarm is not detected 1 - ds-0 yellow alarm is detected n ote : by default, ds-0 yellow alarm is detected on the ingress (rtip/ rring) side. to detect ds-0 yel on the egress (txser) side, the ds-0 switch bit (bit 2) must be set to "1" in register 0xn112. 5 sig rur/ wc 0 change in signaling bits interrupt status this reset-upon-read bit field indicates whether or not the ?change in signaling bits? interrupt has occurred since the last read of this register. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt whenever any one of the four signaling bits values (a,b,c,d) has changed in any one of the 24 channels within the incoming t1 frames. users can read the signali ng change registers (address 0xn10d- 0xn10f) to determine which signalling channel has changed. 0 = indicates that the ?change in signaling bits? interrupt has not occurred since the last read of this register. 1 = indicates that the ?change in signaling bits? interrupt has occurred since the last read of this register. n ote : this bit only has meaning when robbed-bit signaling is enabled. 4 cofa rur/ wc 0 change of frame alignment (cofa) interrupt status this reset-upon-read bit field indicates whether or not the ?change of framing alignment (cofa)? interrupt has occurred since the last read of this register. if this interrupt is enab led, then the receive t1 framer block will generate an interrupt whenever the receive t1 framer block detects a change of framing alignment signal (e.g., the framing bits have appeared to move to a different location within the incoming t1 data stream). 0 = indicates that the ?change of fr aming alignment (cofa)? interrupt has not occurred since the last read of this register. 1 = indicates that the ?change of fr aming alignment (cofa)? interrupt has occurred since the last read of this register.
xrt86vx38 121 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 3 oof_status rur/ wc 0 change in receive out of frame defect condition interrupt status . this reset-upon-read bit field indicates whether or not the ?change in receive out of frame defect condition? interrupt has occurred since the last read of this register. out of frame defect condition is dec lared when ?tolr? out of ?rang? errors in the framing bit pattern is detected. (register 0xn10b) if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block declares the out of frame defect condition. 2. whenever the receive t1 framer block clears the out of frame defect condition 0 = indicates that the ?change in rece ive out of frame defect condition? interrupt has not occurred since the last read of this register 1 = indicates that the ?change in rece ive out of frame defect condition? interrupt has occurred since the last read of this register 2 fmd rur/ wc 0 frame mimic detection interrupt status this reset-upon-read bit field indicates whether or not the ?frame mimic detection? interrupt has occurred sinc e the last read of this register. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt whenever the rece ive t1 framer block detects the presence of frame mimic bits (i.e., the payload bits have appeared to mimic the framing bit pattern withi n the incoming t1 data stream). 0 = indicates that the ?frame mimic detection? interrupt has not occurred since the last read of this register. 1 = indicates that the ?frame mimic detection? interrupt has occurred since the last read of this register. 1 se rur/ wc 0 synchronization bit error (crc-6) interrupt status this reset-upon-read bit field indicates whether or not the ?crc-6 error? interrupt has occurred since the last read of this register. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt whenever the re ceive t1 framer block detects a crc-6 error within the incoming t1 multiframe. 0 = indicates that the ?crc-6 error? interrupt has not occurred since the last read of this register. 1 = indicates that the ?crc-6 error? in terrupt has occurred since the last read of this register. 0 fe rur/ wc 0 framing error interrupt status this reset-upon-read bit field indicates whether or not a ?framing error? interrupt has occurred since the last read of this register. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt whenever the rece ive t1 framer block detects one or more framing alignment bit error within the incoming t1 data stream. 0 = indicates that the ?framing error? interrupt has not occurred since the last read of this register. 1 = indicates that the ?framing error? interrupt has occurred since the last read of this register. n ote : this bit doesn't not necessarily indicate that synchronization has been lost. t able 117: f ramer i nterrupt s tatus r egister (fisr) h ex a ddress : 0 x nb04 b it f unction t ype d efault d escription -o peration
xrt86vx38 122 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 118: f ramer i nterrupt e nable r egister (fier) h ex a ddress : 0 x nb05 b it f unction t ype d efault d escription -o peration 7 ds0 enb r/w 0 ds-0 yellow alarm this bit is used to enable or disable the ds-0 yellow alarm interrupt within the framer block. this yellow alarm is independent of the framing format selected. any time a ds-0 yellow alarm occurs (bit 2 = 0 in each ds-0 time slot), bit 7 and bit 6 in register 0xnb04 will report the status. 0 - disables the interrupt generation 1 - enables the interrupt generation n ote : by default, ds-0 yellow alarm is detected on the ingress (rtip/ rring) side. to detect ds-0 yel on the egress (txser) side, the ds-0 switch bit (bit 2) must be set to "1" in register 0xn112. 6 reserved - - reserved 5 sig_enb r/w 0 change in signaling bits interrupt enable this bit permits the user to either enable or disable the ?change in sig - naling bits? interrupt, within the xrt 86vx38 device. if the user enables this interrupt, then the receive t1 framer block will generate an inter - rupt when it detects a ch ange in the any four signaling bits (a,b,c,d) in any one of the 24 signaling chan nels. users can read the signaling change registers (address 0xn10d-0xn10f) to determine which sig - nalling channel has changed state. 0 - disables the change in signaling bits interrupt 1 - enables the change in signaling bits interrupt n ote : this bit has no meaning when robbed-bit signaling is disabled. 4 cofa_enb r/w 0 change of framing alignment (cofa) interrupt enable this bit permits the user to either enable or disable the ?change in fas framing alignment (cofa)? interrupt, within the xrt86vx38 device. if the user enables this interrupt, then the receive t1 framer block will generate an interrupt when it detect s a change of framing alignment signal (e.g., the framing bits have appeared to move to a different location within the incoming t1 data stream). 0 - disables the ?change of framing alignment (cofa)? interrupt. 1 - enables the ?change of framing alignment (cofa)? interrupt. 3 oof_enb r/w 0 change in out of frame defect condition interrupt enable this bit permits the user to either enable or disable the ?change in out of frame defect condition? interrup t, within the xrt86vx38 device. if the user enables this interrupt, then the receive t1 framer block will generate an interrupt in response to either one of the following condi - tions. 1. the instant that the receive t1 framer block declares the out of frame defect condition. 2. the instant that the receive t1 framer block clears the out of frame defect condition. 0 ? disables the ?change in out of frame defect condition? interrupt. 1 ? enables the ?change in out of frame defect condition? interrupt.
xrt86vx38 123 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 2 fmd_enb r/w 0 frame mimic detection interrupt enable this bit permits the user to either enable or disable the ?frame mimic detection? interrupt, within the xrt86vx38 device. if the user enables this interrupt, then the receive t1 framer block will generate an inter - rupt when it detects the presence of frame mimic bits (i.e., the payload bits have appeared to mimic the framing bit pattern within the incoming t1 data stream). 0 - disables the ?frame mi mic detection? interrupt. 1 - enables the ?frame mi mic detection? interrupt. 1 se_enb r/w 0 synchronization bit (crc-6) error interrupt enable this bit permits the user to either enable or disable the ?crc-6 error detection? interrupt, within the xrt86vx38 device. if the user enables this interrupt, then the receive t1 framer block will generate an inter - rupt when it detects a crc-6 error within the incomi ng t1 multiframe. 0 - disables the ?crc-6 error detection? interrupt. 1 - enables the ?crc-6 error detection? interrupt. 0 fe_enb r/w 0 framing bit error interrupt enable this bit permits the user to either enable or disable the ?framing align - ment bit error detection? interrupt, within the xrt86vx38 device. if the user enables this interrupt, then the receive t1 framer block will generate an interrupt when it detects one or more framing alignment bit error within the incoming t1 data stream. 0 - disables the ?framing alignment bit error detection? interrupt. 1 - enables the ?framing alignment bit error detection? interrupt. n ote : detecting framing alignment bit error doesn't not necessarily indicate that synchronization has been lost. t able 118: f ramer i nterrupt e nable r egister (fier) h ex a ddress : 0 x nb05 b it f unction t ype d efault d escription -o peration
xrt86vx38 124 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 119: d ata l ink s tatus r egister 1 (dlsr1) h ex a ddress : 0 x nb06 b it f unction t ype d efault d escription -o peration 7 msg type ro 0 hdlc1 message type identifier this read only bit indicates the type of data link message received by receive hdlc 1 controller. two types of data link mes - sages are supported within the xrt86vx38 device: message ori - ented signaling (mos) or bit-oriented signalling (bos). 0 = indicates bit-oriented signaling (bos) type data link message is received 1 = indicates message oriented signaling (mos) type data link message is received 6 txsot rur/ wc 0 transmit hdlc1 controller start of transmission (txsot) interrupt status this reset-upon-read bit indicates whether or not the ?transmit hdlc1 controller start of transmission (txsot) ?interrupt has occurred since the last read of this register. transmit hdlc1 con - troller will declare this interrupt when it has started to transmit a data link message. for sending large hdlc messages, start loading the next available buffer once this interrupt is detected. 0 = transmit hdlc1 controller start of transmission (txsot) inter - rupt has not occurred since the last read of this register 1 = transmit hdlc1 controller start of transmission interrupt (txsot) has occurred since the last read of this register. 5 rxsot rur/ wc 0 receive hdlc1 controller start of reception (rxsot) interrupt status this reset-upon-read bit indicates whether or not the receive hdlc1 controller start of reception (rxsot) interrupt has occurred since the last read of this register. receive hdlc1 con - troller will declare this interrupt when it has started to receive a data link message. 0 = receive hdlc1 controller start of reception (rxsot) interrupt has not occurred since the last read of this register 1 = receive hdlc1 controller start of reception (rxsot) interrupt has occurred since the last read of this register 4 txeot rur/ wc 0 transmit hdlc1 controller end of transmission (txeot) inter - rupt status this reset-upon-read bit indicates whether or not the transmit hdlc1 controller end of transmission (txeot) interrupt has occurred since the last read of this register. transmit hdlc1 con - troller will declare this interrupt when it has completed its transmis - sion of a data link message. for sending large hdlc messages, it is critical to load the next av ailable buffer before this interrupt occurs. 0 = transmit hdlc1 controller end of transmission (txeot) inter - rupt has not occurred since the last read of this register 1 = transmit hdlc1 controller end of transmission (txeot) inter - rupt has occurred since the last read of this register
xrt86vx38 125 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 3 rxeot rur/ wc 0 receive hdlc1 controller end of reception (rxeot) interrupt status this reset-upon-read bit indicates whether or not the receive hdlc1 controller end of reception (rxeot) interrupt has occurred since the last read of this register. receive hdlc1 controller will declare this interrupt once it has completely received a full data link message, or once the buffer is full. 0 = receive hdlc1 controller end of reception (rxeot) interrupt has not occurred since the last read of this register 1 = receive hdlc1 controller end of reception (rxeot) interrupt has occurred since the last read of this register 2 fcs error rur/ wc 0 fcs error interrupt status this reset-upon-read bit indicates whether or not the fcs error interrupt has occurred since the last read of this register. receive hdlc1 controller will declare this interrupt when it has detected the fcs error in the most recently received data link message. 0 = fcs error interrupt has not occu rred since the last read of this register 1 = fcs error interrupt has occurred since the last read of this regis - ter 1 rx abort rur/ wc 0 receipt of abort sequence interrupt status this reset-upon-read bit indicates whether or not the receipt of abort sequence interrupt has occurred since last read of this regis - ter. receive hdlc1 controller will decla re this interrupt if it detects the abort sequence (i.e. a string of seven (7) consecutive 1?s) in the incoming data link channel. 0 = receipt of abort sequence interrupt has not occurred since last read of this register 1 = receipt of abort sequence interrupt has occurred since last read of this register 0 rxidle rur/ wc 0 receipt of idle sequence interrupt status this reset-upon-read bit indicates whether or not the receipt of idle sequence interrupt has occurred since the last read of this reg - ister. the receive hdlc1 controller will declare this interrupt if it detects the flag sequence octet (0x7e) in the incoming data link channel. if rxidle "and" rxeo t occur together, then the entire hdlc message has been received. 0 = receipt of idle sequence interrupt has not occurred since last read of this register 1 = receipt of idle sequence interrupt has occurred since last read of this register. t able 119: d ata l ink s tatus r egister 1 (dlsr1) h ex a ddress : 0 x nb06 b it f unction t ype d efault d escription -o peration
xrt86vx38 126 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 120: d ata l ink i nterrupt e nable r egister 1 (dlier1) h ex a ddress : 0 x nb07 b it f unction t ype d efault d escription -o peration 7 reserved - - reserved 6 txsot enb r/w 0 transmit hdlc1 controller start of transmission (txsot) interrupt enable this bit enables or disables the ?transmit hdlc1 controller start of transmission (txsot) ?interrupt within the xrt86vx38 device. once this interrupt is enabled, the transmit hdlc1 controller will generate an interrupt when it has started to transmit a data link mes - sage. 0 = disables the transmit hdlc1 controller start of transmission (txsot) interrupt. 1 = enables the transmit hdlc1 controller start of transmission (txsot) interrupt. 5 rxsot enb r/w 0 receive hdlc1 controller start of reception (rxsot) interrupt enable this bit enables or disables the ?receive hdlc1 controller start of reception (rxsot) ?interrupt within the xrt86vx38 device. once this interrupt is enabled, the receive hdlc1 controller will generate an interrupt when it has started to receive a data link message. 0 = disables the receive hdlc1 controller start of reception (rxsot) interrupt. 1 = enables the receive hdlc1 controller start of reception (rxsot) interrupt. 4 txeot enb r/w 0 transmit hdlc1 controller end of transmission (txeot) inter - rupt enable this bit enables or disables the ?transmit hdlc1 controller end of transmission (txeot) ?interrupt within the xrt86vx38 device. once this interrupt is enabled, the transmit hdlc1 controller will generate an interrupt when it has finished transmitting a data link message. 0 = disables the transmit hdlc1 controller end of transmission (txeot) interrupt. 1 = enables the transmit hdlc1 controller end of transmission (txeot) interrupt. 3 rxeot enb r/w 0 receive hdlc1 controller end of reception (rxeot) interrupt enable this bit enables or disables the ?receive hdlc1 controller end of reception (rxeot) ?interrupt within the xrt86vx38 device. once this interrupt is enabled, the receive hdlc1 controller will generate an interrupt when it has finished receiving a complete data link mes - sage. 0 = disables the receive hdlc1 controller end of reception (rxeot) interrupt. 1 = enables the receive hdlc1 controller end of reception (rxeot) interrupt.
xrt86vx38 127 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 2 fcs err enb r/w 0 fcs error interrupt enable this bit enables or disables the ?received fcs error ?interrupt within the xrt86vx38 device. once this interrupt is enabled, the receive hdlc1 controller will ge nerate an interrupt when it has detected the fcs error within the incoming data link message. 0 = disables the ?receive fcs error? interrupt. 1 = enables the ?receive fcs error? interrupt. 1 rxabort enb r/w 0 receipt of abort sequence interrupt enable this bit enables or disables the ?receipt of abort sequence? inter - rupt within the xrt86vx38 device. once this interrupt is enabled, the receive hdlc1 controller will generate an interrupt when it has detected the abort sequence (i.e. a string of seven (7) consecutive 1?s) within the incoming data link channel. 0 = disables the ?receipt of abort sequence? interrupt. 1 = enables the ?receipt of abort sequence? interrupt. 0 rxidle enb r/w 0 receipt of idle sequence interrupt enable this bit enables or disables the ?receipt of idle sequence? interrupt within the xrt86vx38 device. once this interrupt is enabled, the receive hdlc1 controller will ge nerate an interrupt when it has detected the idle sequence octet (i.e. 0x7e) within the incoming data link channel. 0 = disables the ?receipt of idle sequence? interrupt. 1 = enables the ?receipt of idle sequence? interrupt. t able 120: d ata l ink i nterrupt e nable r egister 1 (dlier1) h ex a ddress : 0 x nb07 b it f unction t ype d efault d escription -o peration
xrt86vx38 128 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 121: s lip b uffer i nterrupt s tatus r egister (sbisr) h ex a ddress : 0 x nb08 b it f unction t ype d efault d escription -o peration 7 txsb_full rur/ wc 0 transmit slip buffer full interrupt status this reset-upon-read bit indicates whether or not the transmit slip buffer full interrupt has occurred sinc e the last read of this register. the transmit slip buffer full interrupt is declared when the transmit slip buffer is filled. if the transmit slip buffer is full and a write oper - ation occurs, then a full frame of da ta will be deleted, and this inter - rupt bit will be set to ?1?. 0 = indicates that the transmit slip buffer full interrupt has not occurred since the last read of this register. 1 = indicates that the transmit slip buffer full interrupt has occurred since the last read of this register. 6 txsb_empt rur/ wc 0 transmit slip buffer empty interrupt status this reset-upon-read bit indicates whether or not the transmit slip buffer empty interrupt has occurred since the last read of this regis - ter. the transmit slip buffer empty interrupt is declared when the transmit slip buffer is emptied. if th e transmit slip buffer is emptied and a read operation occurs, t hen a full frame of data will be repeated, and this interrupt bit will be set to ?1?. 0 = indicates that the transmit slip buffer empty interrupt has not occurred since the last read of this register. 1 = indicates that the transmit slip buffer empty interrupt has occurred since the last read of this register. 5 txsb_slip rur/ wc 0 transmit slip buffer slips interrupt status this reset-upon-read bit indicates whether or not the transmit slip buffer slips interrupt has occurred since the last read of this register. the transmit slip buffer slips inte rrupt is declared when the transmit slip buffer is either filled or emptied. this interrupt bit will be set to ?1? in either one of these two conditions: 1. if the transmit slip buffer is emptied and a read operation occurs, then a full frame of data will be repeated, and this interrupt bit will be set to ?1?. 2. if the transmit slip buffer is full and a write operation occurs, then a full frame of data will be deleted, and this interrupt bit will be set to ?1?. 0 = indicates that the transmit slip buffer slips interrupt has not occurred since the last read of this register. 1 = indicates that the transmit slip buffer slips interrupt has occurred since the last read of this register. n ote : users still need to read the tr ansmit slip buffer empty interrupt (bit 6 of this registe r) or the transmit slip buffer full interrupts (bit 7 of this register) to determine whether transmit slip buffer empties or fills.
xrt86vx38 129 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 4 slc ? 96 lock ro 0 slc ? 96 is in sync this read only bit field indicates whether or not frame synchroni - zation is achieved when the xrt86vx38 is configured in slc ? 96 framing mode. 0 = indicates that frame synchronization is not achieved in slc ? 96 framing mode. 1 = indicates that frame synchronization is achieved in slc ? 96 framing mode. 3 multiframe lock ro 0 multiframe is in sync this read only bit field indicates whether or not the t1 receive framer block is declaring t1 multiframe lock status. 0 = indicates that the t1 receive framer is currently declaring t1 multiframe loss of lock status 0 = indicates that the t1 receive framer is currently declaring t1 multiframe lock status 2 rxsb_full rur/ wc 0 receive slip buffer full interrupt status this reset-upon-read bit indicates whether or not the receive slip buffer full interrupt has occurred since the last read of this register. the receive slip buffer full interrupt is declared when the receive slip buffer is filled. if the receive slip buffer is full and a write oper - ation occurs, then a full frame of da ta will be deleted, and this inter - rupt bit will be set to ?1?. 0 = indicates that the receive slip buffer full interrupt has not occurred since the last read of this register. 1 = indicates that the receive slip buffer full interrupt has occurred since the last read of this register. t able 121: s lip b uffer i nterrupt s tatus r egister (sbisr) h ex a ddress : 0 x nb08 b it f unction t ype d efault d escription -o peration
xrt86vx38 130 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description 1 rxsb_empt rur/ wc 0 receive slip buffer empty interrupt status this reset-upon-read bit indicates whether or not the receive slip buffer empty interrupt has occurred since the last read of this regis - ter. the receive slip buffer empty interrupt is declared when the receive slip buffer is emptied. if the receive slip buffer is emptied and a read operation occurs, then a full frame of data will be repeated, and this interrupt bit will be set to ?1?. 0 = indicates that the receive slip buffer empty interrupt has not occurred since the last read of this register. 1 = indicates that the receive slip buffer empty interrupt has occurred since the last read of this register. 0 rxsb_slip rur/ wc 0 receive slip buffer slips interrupt status this reset-upon-read bit indicates whether or not the receive slip buffer slips interrupt has occurred since the last read of this register. the receive slip buffer slips inte rrupt is declared when the receive slip buffer is either filled or emptied. this interrupt bit will be set to ?1? in either one of these two conditions: 1. if the receive slip buffer is emptied and a read operation occurs, then a full frame of data will be repeated, and this interrupt bit will be set to ?1?. 2. if the receive slip buffer is full and a write operation occurs, then a full frame of data will be deleted, and this interrupt bit will be set to ?1?. 0 = indicates that the receive slip buffer slips interrupt has not occurred since the last read of this register. 1 = indicates that the receive slip buffer slips interrupt has occurred since the last read of this register. n ote : users still need to read t he receive slip buffer empty interrupt (bit 1 of this register) or the receive slip buffer full interrupts (bit 2 of this register) to determine whether transmit slip buffer empties or fills. t able 121: s lip b uffer i nterrupt s tatus r egister (sbisr) h ex a ddress : 0 x nb08 b it f unction t ype d efault d escription -o peration
xrt86vx38 131 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 122: s lip b uffer i nterrupt e nable r egister (sbier) h ex a ddress : 0 x nb09 b it f unction t ype d efault d escription -o peration 7 txfull_enb r/w 0 transmit slip buffer full interrupt enable this bit enables or disables the transmit slip buffer full interrupt within the xrt86vx38 device. once this interrupt is enabled, the transmit slip buffer full interrupt is declared when the transmit slip buffer is filled. if the transmit sl ip buffer is full and a write opera - tion occurs, then a full frame of data will be deleted, and the interrupt status bit will be set to ?1?. 0 - disables the transmit slip buffer full interrupt when the transmit slip buffer fills 1 - enables the transmit slip buffer full interrupt when the transmit slip buffer fills. 6 txempt_enb r/w 0 transmit slip buffer empty interrupt enable this bit enables or disables the transmit slip buffer empty interrupt within the xrt86vx38 device. once this interrupt is enabled, the transmit slip buffer empty interrupt is declared when the transmit slip buffer is emptied. if the transmit slip buffer is emptied and a read operation occurs, then a full frame of data will be repeated, and the interrupt status bit will be set to ?1?. 0 - disables the transmit slip buffer empty interrupt when the transmit slip buffer empties 1 - enables the transmit slip buffer empty interrupt when the trans - mit slip buffer empties. 5 txslip_enb r/w 0 transmit slip buffer slips interrupt enable this bit enables or disables the transmit slip buffer slips interrupt within the xrt86vx38 device. once this interrupt is enabled, the transmit slip buffer slips interrupt is declared when either the trans - mit slip buffer is filled or emptied. if the transmit slip buffer is emptied and a read operation occurs, t hen a full frame of data will be repeated, and the interrupt status bit will be set to ?1?. the interrupt status bit will be set to ?1? in either one of these two conditions: 1. if the transmit slip buffer is emptied and a read operation occurs, then a full frame of data will be repeated, and this interrupt bit will be set to ?1?. 2. if the transmit slip buffer is full and a write operation occurs, then a full frame of data will be deleted, and this interrupt bit will be set to ?1?. 0 - disables the transmit slip buffer slips interrupt when the trans - mit slip buffer empties or fills 1 - enables the transmit slip buffer slips interrupt when the trans - mit slip buffer empties or fills. 4-3 reserved - - reserved
xrt86vx38 132 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description 2 rxfull_enb r/w 0 receive slip buffer full interrupt enable this bit enables or disables the receive slip buffer full interrupt within the xrt86vx38 device. once this interrupt is enabled, the receive slip buffer full interrupt is declared when the receive slip buffer is filled. if the receive slip buffer is full and a write opera - tion occurs, then a full frame of data will be deleted, and the interrupt status bit will be set to ?1?. 0 - disables the receive slip buffer full interrupt when the transmit slip buffer fills 1 - enables the receive slip buffer full interrupt when the transmit slip buffer fills. 1 rxempt_enb r/w 0 receive slip buffer empty interrupt enable this bit enables or disables the receives slip buffer empty interrupt within the xrt86vx38 device. once this interrupt is enabled, the receive slip buffer empty interrupt is declared when the receive slip buffer is emptied. if the receive slip buffer is emptied and a read operation occurs, then a full frame of data will be repeated, and the interrupt status bit will be set to ?1?. 0 - disables the receive slip buffer empty interrupt when the trans - mit slip buffer empties 1 - enables the receive slip buffer empty interrupt when the trans - mit slip buffer empties. 0 rxslip_enb r/w 0 receive slip buffer slips interrupt enable this bit enables or disables the receive slip buffer slips interrupt within the xrt86vx38 device. once this interrupt is enabled, the receive slip buffer slips interrupt is declared when either the receive slip buffer is filled or empt ied. if the receive slip buffer is emptied and a read operation occurs , then a full frame of data will be repeated, and the interrupt status bit will be set to ?1?. the interrupt status bit will be set to ?1? in either one of these two conditions: 1. if the receive slip buffer is emptied and a read operation occurs, then a full frame of data will be repeated, and this interrupt bit will be set to ?1?. 2. if the receive slip buffer is full and a write operation occurs, then a full frame of data will be deleted, and this interrupt bit will be set to ?1?. 0 - disables the receive slip buffer slips interrupt when the trans - mit slip buffer empties or fills 1 - enables the receive slip buffer slips interrupt when the trans - mit slip buffer empties or fills. t able 122: s lip b uffer i nterrupt e nable r egister (sbier) h ex a ddress : 0 x nb09 b it f unction t ype d efault d escription -o peration
xrt86vx38 133 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 123: r eceive l oopback c ode 0 i nterrupt and s tatus r egister (rlcisr0) h ex a ddress : 0 x nb0a b it f unction t ype d efault d escription -o peration 7-4 - - - reserved (for e1 mode only) 3 rxastat ro 0 receive loopback activation code state this read only bit indicates whether or not the receive t1 framer block is currently detecting the receive loopback ac tivation code, as specified in the receive loopback activation code register (rlacr - address 0xn126) if receive loopback activation code detection is enabled. 0 = indicates that the receive t1 framer block is not currently detecting the receive loopback activation code. 1 = indicates that the receive t1 framer block is currently detecting the receive loopback activation code. 2 rxdstat ro 0 receive loopback deactivation code state this read only bit indicates whether or not the receive t1 framer block is currently detecting the receive loopback de activation code, as specified in the receive loopback deactivation code register (rldcr - address 0xn127) if receive loopback deactivation code detection is enabled. 0 = indicates that the receive t1 framer block is not currently detecting the receive loopback deactivation code. 1 = indicates that the receive t1 framer block is currently detecting the receive loopback deactivation code. 1 rxaint rur/ wc 0 change in receive loopback activation code interrupt status this reset-upon-read bit field indicates whether or not the ?change in receive loopback activation code? interrupt has occurred since the last read of this register. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block detects the receive loopback activation code. 2. whenever the receive t1 framer block no longer detects the receive loopback activation code. 0 = indicates that the ?change in receive loopback activation code? inter - rupt has not occurred since the last read of this register 1 = indicates that the ?change in receive loopback activation code? inter - rupt has occurred since the last read of this register 0 rxdint rur/ wc 0 change in receive loopback deactivation code interrupt status this reset-upon-read bit field indicates whether or not the ?change in receive loopback deactivation code? interrupt has occurred since the last read of this register. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block detects the receive loopback deactivation code. 2. whenever the receive t1 framer block no longer detects the receive loopback deactivation code. 0 = indicates that the ?change in receive loopback deactivation code? inter - rupt has not occurred since the last read of this register 1 = indicates that the ?change in receive loopback deactivation code? inter - rupt has occurred since the last read of this register
xrt86vx38 134 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 124: r eceive l oopback c ode 0 i nterrupt e nable r egister (rlcier0) h ex a ddress : 0 x nb0b b it f unction t ype d efault d escription -o peration 7-2 reserved - - reserved 1 rxaenb r/w 0 receive loopback activation code interrupt enable this bit enables or disables the ?change in receive loopback acti - vation code? interrupt within the t1 receive framer. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block detects the receive loopback activation code. 2. whenever the receive t1 framer block no longer detects the receive loopback activation code. 0 - disables the ?change in receive loopback activation code? interrupt within the t1 receive framer. 1 - enables the ?change in receive loopback activation code? interrupt within the t1 receive framer. 0 rxdenb r/w 0 receive loopback deactivation code interrupt enable this bit enables or disables the ?change in receive loopback deactivation code? interrupt within the t1 receive framer. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block detects the receive loopback deactivation code. 2. whenever the receive t1 framer block no longer detects the receive loopback deactivation code. 0 - disables the ?change in receive loopback deactivation code? interrupt within the t1 receive framer. 1 - enables the ?change in receive loopback deactivation code? interrupt within the t1 receive framer.
xrt86vx38 135 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 125: e xcessive z ero s tatus r egister (exzsr) h ex a ddress : 0 x nb0e b it f unction t ype d efault d escription -o peration 7-1 reserved - - reserved 0 exz_status rur/ wc 0 change in excessive zero condition interrupt status this reset-upon-read bit field indicates whether or not the ?change in excessive zero condition? interrupt within the t1 receive framer block has occurred since the last read of this register. if this interrupt is enabled, then the receive t1 framer block will gener - ate an interrupt in response to eit her one of the following conditions. 1. whenever the receive t1 framer block detects the excessive zero condition. 2. whenever the receive t1 framer block clears the excessive zero condition 0 = indicates the ?change in excessive zero condition? interrupt has not occurred since the last read of this register 1 = indicates the ?change in excessive zero condition? interrupt has occurred since the last read of this register t able 126: e xcessive z ero e nable r egister (exzer) h ex a ddress : 0 x nb0f b it f unction t ype d efault d escription -o peration 7-1 - - - reserved 0 exz_enb r/w 0 change in excessive zero condition interrupt enable this bit enables or disables the ?change in excessive zero condi - tion? interrupt within the t1 receive framer. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block detects the excessive zero condition. 2. whenever the receive t1 framer block clears the excessive zero condition 0 - disables the ?change in excessive zero condition? interrupt within the receive t1 framer block 1 - enables the ?change in excessive zero condition? interrupt within the receive t1 framer block
xrt86vx38 136 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 127: ss7 s tatus r egister for lapd1 (ss7sr1) h ex a ddress : 0 x nb10 b it f unction t ype d efault d escription -o peration 0 ss7_1_status rur/ wc 0 ss7 interrupt status fo r lapd controller 1 this reset-upon-read bit field indicates whether or not the ?ss7? interrupt has occurred since the last read of this register. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt when the received lapd message is more than 276 bytes in length. 0 = indicates that the ?ss7? interrupt has not occurred since the last read of this register 1 = indicates that the ?ss7? interrupt has occurred since the last read of this register t able 128: ss7 e nable r egister for lapd1 (ss7er1) h ex a ddress : 0 x nb11 b it f unction t ype d efault d escription -o peration 0 ss7_1_enb r/w 0 ss7 interrupt enable fo r lapd controller 1 this bit enables or disables the ?ss7? interrupt within the lapd controller 1. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt when the received lapd message is more than 276 bytes in length. 0 - disables the ?ss7? interrupt within the lapd controller 1. 1 - enables the ?ss7? interrupt within the lapd controller 1.
xrt86vx38 137 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 129: r x los/crc i nterrupt s tatus r egister (rlcisr) h ex a ddress : 0 x nb12 b it f unction t ype d efault d escription -o peration 7-4 - - - reserved 3 rxlosint rur/ wc 0 change in receive los condition interrupt status this bit indicates whether or no t the ?change in receive los condi - tion? interrupt has occurred since the last read of this register. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block declares the receive los condition. 2. whenever the receive t1 framer block clears the receive los condition. 0 = indicates that the ?change in receive los condition? interrupt has not occurred since the last read of this register. 1 = indicates that the ?change in receive los condition? interrupt has occurred since the last read of this register. 2-0 reserved - - t able 130: r x los/crc i nterrupt e nable r egister (rlcier) h ex a ddress : 0 x nb13 b it f unction t ype d efault d escription -o peration 3 rxlos_enb r/w 0 change in receive los condition interrupt enable this bit enables the ?change in receive los condition? interrupt. 0 = enables ?change in receive los condition? interrupt. 1 = disables ?change in receive los condition? interrupt. 2-0 - - - reserved
xrt86vx38 138 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 131: r eceive l oopback c ode 1 i nterrupt and s tatus r egister (rlcisr1) h ex a ddress : 0 x nb14 b it f unction t ype d efault d escription -o peration 7-4 - - - reserved (for e1 mode only) 3 rxastat ro 0 receive loopback activation code state this read only bit indicates whether or not the receive t1 framer block is currently detecting the receive loopback ac tivation code, as specified in the receive loopback activation code register (rlacr) if receive loopback activation code detection is enabled. 0 = indicates that the receive t1 framer block is not currently detecting the receive loopback activation code. 1 = indicates that the receive t1 framer block is currently detecting the receive loopback activation code. 2 rxdstat ro 0 receive loopback deactivation code state this read only bit indicates whether or not the receive t1 framer block is currently detecting the receive loopback de activation code, as specified in the receive loopback deactivation code register (rldcr) if receive loop - back deactivation code detection is enabled. 0 = indicates that the receive t1 framer block is not currently detecting the receive loopback deactivation code. 1 = indicates that the receive t1 framer block is currently detecting the receive loopback deactivation code. 1 rxaint rur/ wc 0 change in receive loopback activation code interrupt status this reset-upon-read bit field indicates whether or not the ?change in receive loopback activation code? interrupt has occurred since the last read of this register. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block detects the receive loopback activation code. 2. whenever the receive t1 framer block no longer detects the receive loopback activation code. 0 = indicates that the ?change in receive loopback activation code? inter - rupt has not occurred since the last read of this register 1 = indicates that the ?change in receive loopback activation code? inter - rupt has occurred since the last read of this register 0 rxdint rur/ wc 0 change in receive loopback deactivation code interrupt status this reset-upon-read bit field indicates whether or not the ?change in receive loopback deactivation code? interrupt has occurred since the last read of this register. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block detects the receive loopback deactivation code. 2. whenever the receive t1 framer block no longer detects the receive loopback deactivation code. 0 = indicates that the ?change in receive loopback deactivation code? inter - rupt has not occurred since the last read of this register 1 = indicates that the ?change in receive loopback deactivation code? inter - rupt has occurred since the last read of this register
xrt86vx38 139 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 132: r eceive l oopback c ode 1 i nterrupt e nable r egister (rlcier1) h ex a ddress : 0 x nb15 b it f unction t ype d efault d escription -o peration 7-2 reserved - - reserved 1 rxaenb r/w 0 receive loopback activation code interrupt enable this bit enables or disables the ?change in receive loopback acti - vation code? interrupt within the t1 receive framer. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block detects the receive loopback activation code. 2. whenever the receive t1 framer block no longer detects the receive loopback activation code. 0 - disables the ?change in receive loopback activation code? interrupt within the t1 receive framer. 1 - enables the ?change in receive loopback activation code? interrupt within the t1 receive framer. 0 rxdenb r/w 0 receive loopback deactivation code interrupt enable this bit enables or disables the ?change in receive loopback deactivation code? interrupt within the t1 receive framer. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block detects the receive loopback deactivation code. 2. whenever the receive t1 framer block no longer detects the receive loopback deactivation code. 0 - disables the ?change in receive loopback deactivation code? interrupt within the t1 receive framer. 1 - enables the ?change in receive loopback deactivation code? interrupt within the t1 receive framer.
xrt86vx38 140 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 133: d ata l ink s tatus r egister 2 (dlsr2) h ex a ddress : 0 x nb16 b it f unction t ype d efault d escription -o peration 7 msg type ro 0 hdlc2 message type identifier this read only bit indicates the type of data link message received by receive hdlc 2 controller. two types of data link mes - sages are supported within the xrt86vx38 device: message ori - ented signaling (mos) or bit-oriented signalling (bos). 0 = indicates bit-oriented signaling (bos) type data link message is received 1 = indicates message oriented signaling (mos) type data link message is received 6 txsot rur/ wc 0 transmit hdlc2 controller start of transmission (txsot) interrupt status this reset-upon-read bit indicates whether or not the ?transmit hdlc2 controller start of transmission (txsot) ?interrupt has occurred since the last read of this register. transmit hdlc2 con - troller will declare this interrupt when it has started to transmit a data link message. for sending large hdlc messages, start loading the next available buffer once this interrupt is detected. 0 = transmit hdlc2 controller start of transmission (txsot) inter - rupt has not occurred since the last read of this register 1 = transmit hdlc2 controller start of transmission interrupt (txsot) has occurred since the last read of this register. 5 rxsot rur/ wc 0 receive hdlc2 controller start of reception (rxsot) interrupt status this reset-upon-read bit indicates whether or not the receive hdlc2 controller start of reception (rxsot) interrupt has occurred since the last read of this register. receive hdlc2 con - troller will declare this interrupt when it has started to receive a data link message. 0 = receive hdlc2 controller start of reception (rxsot) interrupt has not occurred since the last read of this register 1 = receive hdlc2 controller start of reception (rxsot) interrupt has occurred since the last read of this register 4 txeot rur/ wc 0 transmit hdlc2 controller end of transmission (txeot) inter - rupt status this reset-upon-read bit indicates whether or not the transmit hdlc2 controller end of transmission (txeot) interrupt has occurred since the last read of this register. transmit hdlc2 con - troller will declare this interrupt when it has completed its transmis - sion of a data link message. for sending large hdlc messages, it is critical to load the next av ailable buffer before this interrupt occurs. 0 = transmit hdlc2 controller end of transmission (txeot) inter - rupt has not occurred since the last read of this register 1 = transmit hdlc2 controller end of transmission (txeot) inter - rupt has occurred since the last read of this register
xrt86vx38 141 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 3 rxeot rur/ wc 0 receive hdlc2 controller end of reception (rxeot) interrupt status this reset-upon-read bit indicates whether or not the receive hdlc2 controller end of reception (rxeot) interrupt has occurred since the last read of this register. receive hdlc2 controller will declare this interrupt once it has completely received a full data link message, or once the buffer is full. 0 = receive hdlc2 controller end of reception (rxeot) interrupt has not occurred since the last read of this register 1 = receive hdlc2 controller end of reception (rxeot) interrupt has occurred since the last read of this register 2 fcs error rur/ wc 0 fcs error interrupt status this reset-upon-read bit indicates whether or not the fcs error interrupt has occurred since the last read of this register. receive hdlc2 controller will declare this interrupt when it has detected the fcs error in the most recently received data link message. 0 = fcs error interrupt has not occu rred since the last read of this register 1 = fcs error interrupt has occurred since the last read of this regis - ter 1 rx abort rur/ wc 0 receipt of abort sequence interrupt status this reset-upon-read bit indicates whether or not the receipt of abort sequence interrupt has occurred since last read of this regis - ter. receive hdlc2 controller will decla re this interrupt if it detects the abort sequence (i.e. a string of seven (7) consecutive 1?s) in the incoming data link channel. 0 = receipt of abort sequence interrupt has not occurred since last read of this register 1 = receipt of abort sequence interrupt has occurred since last read of this register 0 rxidle rur/ wc 0 receipt of idle sequence interrupt status this reset-upon-read bit indicates whether or not the receipt of idle sequence interrupt has occurred since the last read of this reg - ister. the receive hdlc2 controller will declare this interrupt if it detects the flag sequence octet (0x7e) in the incoming data link channel. if rxidle "and" rxeot occur together, then the entire hdlc message has been received. 0 = receipt of idle sequence interrupt has not occurred since last read of this register 1 = receipt of idle sequence interrupt has occurred since last read of this register. t able 133: d ata l ink s tatus r egister 2 (dlsr2) h ex a ddress : 0 x nb16 b it f unction t ype d efault d escription -o peration
xrt86vx38 142 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 134: d ata l ink i nterrupt e nable r egister 2 (dlier2) h ex a ddress : 0 x nb17 b it f unction t ype d efault d escription -o peration 7 reserved - - reserved 6 txsot enb r/w 0 transmit hdlc2 controller start of transmission (txsot) interrupt enable this bit enables or disables the ?transmit hdlc2 controller start of transmission (txsot) ?interrupt within the xrt86vx38 device. once this interrupt is enabled, the transmit hdlc2 controller will generate an interrupt when it has started to transmit a data link mes - sage. 0 = disables the transmit hdlc2 controller start of transmission (txsot) interrupt. 1 = enables the transmit hdlc2 controller start of transmission (txsot) interrupt. 5 rxsot enb r/w 0 receive hdlc2 controller start of reception (rxsot) interrupt enable this bit enables or disables the ?receive hdlc2 controller start of reception (rxsot) ?interrupt within the xrt86vx38 device. once this interrupt is enabled, the receive hdlc2 controller will generate an interrupt when it has started to receive a data link message. 0 = disables the receive hdlc2 controller start of reception (rxsot) interrupt. 1 = enables the receive hdlc2 controller start of reception (rxsot) interrupt. 4 txeot enb r/w 0 transmit hdlc2 controller end of transmission (txeot) inter - rupt enable this bit enables or disables the ?transmit hdlc2 controller end of transmission (txeot) ?interrupt within the xrt86vx38 device. once this interrupt is enabled, the transmit hdlc2 controller will generate an interrupt when it has finished transmitting a data link message. 0 = disables the transmit hdlc2 controller end of transmission (txeot) interrupt. 1 = enables the transmit hdlc2 controller end of transmission (txeot) interrupt. 3 rxeot enb r/w 0 receive hdlc2 controller end of reception (rxeot) interrupt enable this bit enables or disables the ?receive hdlc2 controller end of reception (rxeot) ?interrupt within the xrt86vx38 device. once this interrupt is enabled, the receive hdlc2 controller will generate an interrupt when it has finished receiving a complete data link mes - sage. 0 = disables the receive hdlc2 controller end of reception (rxeot) interrupt. 1 = enables the receive hdlc2 controller end of reception (rxeot) interrupt.
xrt86vx38 143 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 2 fcs err enb r/w 0 fcs error interrupt enable this bit enables or disables the ?received fcs error ?interrupt within the xrt86vx38 device. once this interrupt is enabled, the receive hdlc2 controller will ge nerate an interrupt when it has detected the fcs error within the incoming data link message. 0 = disables the ?receive fcs error? interrupt. 1 = enables the ?receive fcs error? interrupt. 1 rxabort enb r/w 0 receipt of abort sequence interrupt enable this bit enables or disables the ?receipt of abort sequence?inter - rupt within the xrt86vx38 device. once this interrupt is enabled, the receive hdlc2 controller will generate an interrupt when it has detected the abort sequence (i.e. a string of seven (7) consecutive 1?s) within the incoming data link channel. 0 = disables the ?receipt of abort sequence? interrupt. 1 = enables the ?receipt of abort sequence? interrupt. 0 rxidle enb r/w 0 receipt of idle sequence interrupt enable this bit enables or disables the ?receipt of idle sequence?interrupt within the xrt86vx38 device. once this interrupt is enabled, the receive hdlc2 controller will ge nerate an interrupt when it has detected the idle sequence octet (i.e. 0x7e) within the incoming data link channel. 0 = disables the ?receipt of idle sequence? interrupt. 1 = enables the ?receipt of idle sequence? interrupt. t able 134: d ata l ink i nterrupt e nable r egister 2 (dlier2) h ex a ddress : 0 x nb17 b it f unction t ype d efault d escription -o peration
xrt86vx38 144 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 135: ss7 s tatus r egister for lapd2 (ss7sr2) h ex a ddress : 0 x nb18 b it f unction t ype d efault d escription -o peration 0 ss7_2_status rur/ wc 0 ss7 interrupt status fo r lapd controller 2 this reset-upon-read bit field indicates whether or not the ?ss7? interrupt has occurred since the last read of this register. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt when the received lapd message is more than 276 bytes in length. 0 = indicates that the ?ss7? interrupt has not occurred since the last read of this register 1 = indicates that the ?ss7? interrupt has occurred since the last read of this register t able 136: ss7 e nable r egister for lapd2 (ss7er2) h ex a ddress : 0 x nb19 b it f unction t ype d efault d escription -o peration 0 ss7_2_enb r/w 0 ss7 interrupt enable fo r lapd controller 2 this bit enables or disables the ?ss7? interrupt within the lapd controller 2. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt when the received lapd message is more than 276 bytes in length. 0 - disables the ?ss7? interrupt within the lapd controller 2. 1 - enables the ?ss7? interrupt within the lapd controller 2.
xrt86vx38 145 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 137: r eceive l oopback c ode 2 i nterrupt and s tatus r egister (rlcisr2) h ex a ddress : 0 x nb1a b it f unction t ype d efault d escription -o peration 7-4 - - - reserved (for e1 mode only) 3 rxastat ro 0 receive loopback activation code state this read only bit indicates whether or not the receive t1 framer block is currently detecting the receive loopback ac tivation code, as specified in the receive loopback activation code register (rlacr) if receive loopback activation code detection is enabled. 0 = indicates that the receive t1 framer block is not currently detecting the receive loopback activation code. 1 = indicates that the receive t1 framer block is currently detecting the receive loopback activation code. 2 rxdstat ro 0 receive loopback deactivation code state this read only bit indicates whether or not the receive t1 framer block is currently detecting the receive loopback de activation code, as specified in the receive loopback deactivation code register (rldcr) if receive loop - back deactivation code detection is enabled. 0 = indicates that the receive t1 framer block is not currently detecting the receive loopback deactivation code. 1 = indicates that the receive t1 framer block is currently detecting the receive loopback deactivation code. 1 rxaint rur/ wc 0 change in receive loopback activation code interrupt status this reset-upon-read bit field indicates whether or not the ?change in receive loopback activation code? interrupt has occurred since the last read of this register. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block detects the receive loopback activation code. 2. whenever the receive t1 framer block no longer detects the receive loopback activation code. 0 = indicates that the ?change in receive loopback activation code? inter - rupt has not occurred since the last read of this register 1 = indicates that the ?change in receive loopback activation code? inter - rupt has occurred since the last read of this register 0 rxdint rur/ wc 0 change in receive loopback deactivation code interrupt status this reset-upon-read bit field indicates whether or not the ?change in receive loopback deactivation code? interrupt has occurred since the last read of this register. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block detects the receive loopback deactivation code. 2. whenever the receive t1 framer block no longer detects the receive loopback deactivation code. 0 = indicates that the ?change in receive loopback deactivation code? inter - rupt has not occurred since the last read of this register 1 = indicates that the ?change in receive loopback deactivation code? inter - rupt has occurred since the last read of this register
xrt86vx38 146 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 138: r eceive l oopback c ode 2 i nterrupt e nable r egister (rlcier2) h ex a ddress : 0 x nb1b b it f unction t ype d efault d escription -o peration 7-2 reserved - - reserved 1 rxaenb r/w 0 receive loopback activation code interrupt enable this bit enables or disables the ?change in receive loopback acti - vation code? interrupt within the t1 receive framer. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block detects the receive loopback activation code. 2. whenever the receive t1 framer block no longer detects the receive loopback activation code. 0 - disables the ?change in receive loopback activation code? interrupt within the t1 receive framer. 1 - enables the ?change in receive loopback activation code? interrupt within the t1 receive framer. 0 rxdenb r/w 0 receive loopback deactivation code interrupt enable this bit enables or disables the ?change in receive loopback deactivation code? interrupt within the t1 receive framer. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block detects the receive loopback deactivation code. 2. whenever the receive t1 framer block no longer detects the receive loopback deactivation code. 0 - disables the ?change in receive loopback deactivation code? interrupt within the t1 receive framer. 1 - enables the ?change in receive loopback deactivation code? interrupt within the t1 receive framer.
xrt86vx38 147 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 139: r eceive l oopback c ode 3 i nterrupt and s tatus r egister (rlcisr3) h ex a ddress : 0 x nb1c b it f unction t ype d efault d escription -o peration 7-4 - - - reserved (for e1 mode only) 3 rxastat ro 0 receive loopback activation code state this read only bit indicates whether or not the receive t1 framer block is currently detecting the receive loopback ac tivation code, as specified in the receive loopback activation code register (rlacr) if receive loopback activation code detection is enabled. 0 = indicates that the receive t1 framer block is not currently detecting the receive loopback activation code. 1 = indicates that the receive t1 framer block is currently detecting the receive loopback activation code. 2 rxdstat ro 0 receive loopback deactivation code state this read only bit indicates whether or not the receive t1 framer block is currently detecting the receive loopback de activation code, as specified in the receive loopback deactivation code register (rldcr) if receive loop - back deactivation code detection is enabled. 0 = indicates that the receive t1 framer block is not currently detecting the receive loopback deactivation code. 1 = indicates that the receive t1 framer block is currently detecting the receive loopback deactivation code. 1 rxaint rur/ wc 0 change in receive loopback activation code interrupt status this reset-upon-read bit field indicates whether or not the ?change in receive loopback activation code? interrupt has occurred since the last read of this register. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block detects the receive loopback activation code. 2. whenever the receive t1 framer block no longer detects the receive loopback activation code. 0 = indicates that the ?change in receive loopback activation code? inter - rupt has not occurred since the last read of this register 1 = indicates that the ?change in receive loopback activation code? inter - rupt has occurred since the last read of this register 0 rxdint rur/ wc 0 change in receive loopback deactivation code interrupt status this reset-upon-read bit field indicates whether or not the ?change in receive loopback deactivation code? interrupt has occurred since the last read of this register. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block detects the receive loopback deactivation code. 2. whenever the receive t1 framer block no longer detects the receive loopback deactivation code. 0 = indicates that the ?change in receive loopback deactivation code? inter - rupt has not occurred since the last read of this register 1 = indicates that the ?change in receive loopback deactivation code? inter - rupt has occurred since the last read of this register
xrt86vx38 148 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 140: r eceive l oopback c ode 3 i nterrupt e nable r egister (rlcier3) h ex a ddress : 0 x nb1d b it f unction t ype d efault d escription -o peration 7-2 reserved - - reserved 1 rxaenb r/w 0 receive loopback activation code interrupt enable this bit enables or disables the ?change in receive loopback acti - vation code? interrupt within the t1 receive framer. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block detects the receive loopback activation code. 2. whenever the receive t1 framer block no longer detects the receive loopback activation code. 0 - disables the ?change in receive loopback activation code? interrupt within the t1 receive framer. 1 - enables the ?change in receive loopback activation code? interrupt within the t1 receive framer. 0 rxdenb r/w 0 receive loopback deactivation code interrupt enable this bit enables or disables the ?change in receive loopback deactivation code? interrupt within the t1 receive framer. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block detects the receive loopback deactivation code. 2. whenever the receive t1 framer block no longer detects the receive loopback deactivation code. 0 - disables the ?change in receive loopback deactivation code? interrupt within the t1 receive framer. 1 - enables the ?change in receive loopback deactivation code? interrupt within the t1 receive framer.
xrt86vx38 149 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 141: r eceive l oopback c ode 4 i nterrupt and s tatus r egister (rlcisr4) h ex a ddress : 0 x nb1e b it f unction t ype d efault d escription -o peration 7-4 - - - reserved (for e1 mode only) 3 rxastat ro 0 receive loopback activation code state this read only bit indicates whether or not the receive t1 framer block is currently detecting the receive loopback ac tivation code, as specified in the receive loopback activation code register (rlacr) if receive loopback activation code detection is enabled. 0 = indicates that the receive t1 framer block is not currently detecting the receive loopback activation code. 1 = indicates that the receive t1 framer block is currently detecting the receive loopback activation code. 2 rxdstat ro 0 receive loopback deactivation code state this read only bit indicates whether or not the receive t1 framer block is currently detecting the receive loopback de activation code, as specified in the receive loopback deactivation code register (rldcr) if receive loop - back deactivation code detection is enabled. 0 = indicates that the receive t1 framer block is not currently detecting the receive loopback deactivation code. 1 = indicates that the receive t1 framer block is currently detecting the receive loopback deactivation code. 1 rxaint rur/ wc 0 change in receive loopback activation code interrupt status this reset-upon-read bit field indicates whether or not the ?change in receive loopback activation code? interrupt has occurred since the last read of this register. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block detects the receive loopback activation code. 2. whenever the receive t1 framer block no longer detects the receive loopback activation code. 0 = indicates that the ?change in receive loopback activation code? inter - rupt has not occurred since the last read of this register 1 = indicates that the ?change in receive loopback activation code? inter - rupt has occurred since the last read of this register 0 rxdint rur/ wc 0 change in receive loopback deactivation code interrupt status this reset-upon-read bit field indicates whether or not the ?change in receive loopback deactivation code? interrupt has occurred since the last read of this register. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block detects the receive loopback deactivation code. 2. whenever the receive t1 framer block no longer detects the receive loopback deactivation code. 0 = indicates that the ?change in receive loopback deactivation code? inter - rupt has not occurred since the last read of this register 1 = indicates that the ?change in receive loopback deactivation code? inter - rupt has occurred since the last read of this register
xrt86vx38 150 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 142: r eceive l oopback c ode 4 i nterrupt e nable r egister (rlcier4) h ex a ddress : 0 x nb1f b it f unction t ype d efault d escription -o peration 7-2 reserved - - reserved 1 rxaenb r/w 0 receive loopback activation code interrupt enable this bit enables or disables the ?change in receive loopback acti - vation code? interrupt within the t1 receive framer. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block detects the receive loopback activation code. 2. whenever the receive t1 framer block no longer detects the receive loopback activation code. 0 - disables the ?change in receive loopback activation code? interrupt within the t1 receive framer. 1 - enables the ?change in receive loopback activation code? interrupt within the t1 receive framer. 0 rxdenb r/w 0 receive loopback deactivation code interrupt enable this bit enables or disables the ?change in receive loopback deactivation code? interrupt within the t1 receive framer. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block detects the receive loopback deactivation code. 2. whenever the receive t1 framer block no longer detects the receive loopback deactivation code. 0 - disables the ?change in receive loopback deactivation code? interrupt within the t1 receive framer. 1 - enables the ?change in receive loopback deactivation code? interrupt within the t1 receive framer.
xrt86vx38 151 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 143: r eceive l oopback c ode 5 i nterrupt and s tatus r egister (rlcisr5) h ex a ddress : 0 x nb20 b it f unction t ype d efault d escription -o peration 7-4 - - - reserved (for e1 mode only) 3 rxastat ro 0 receive loopback activation code state this read only bit indicates whether or not the receive t1 framer block is currently detecting the receive loopback ac tivation code, as specified in the receive loopback activation code register (rlacr) if receive loopback activation code detection is enabled. 0 = indicates that the receive t1 framer block is not currently detecting the receive loopback activation code. 1 = indicates that the receive t1 framer block is currently detecting the receive loopback activation code. 2 rxdstat ro 0 receive loopback deactivation code state this read only bit indicates whether or not the receive t1 framer block is currently detecting the receive loopback de activation code, as specified in the receive loopback deactivation code register (rldcr) if receive loop - back deactivation code detection is enabled. 0 = indicates that the receive t1 framer block is not currently detecting the receive loopback deactivation code. 1 = indicates that the receive t1 framer block is currently detecting the receive loopback deactivation code. 1 rxaint rur/ wc 0 change in receive loopback activation code interrupt status this reset-upon-read bit field indicates whether or not the ?change in receive loopback activation code? interrupt has occurred since the last read of this register. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block detects the receive loopback activation code. 2. whenever the receive t1 framer block no longer detects the receive loopback activation code. 0 = indicates that the ?change in receive loopback activation code? inter - rupt has not occurred since the last read of this register 1 = indicates that the ?change in receive loopback activation code? inter - rupt has occurred since the last read of this register 0 rxdint rur/ wc 0 change in receive loopback deactivation code interrupt status this reset-upon-read bit field indicates whether or not the ?change in receive loopback deactivation code? interrupt has occurred since the last read of this register. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block detects the receive loopback deactivation code. 2. whenever the receive t1 framer block no longer detects the receive loopback deactivation code. 0 = indicates that the ?change in receive loopback deactivation code? inter - rupt has not occurred since the last read of this register 1 = indicates that the ?change in receive loopback deactivation code? inter - rupt has occurred since the last read of this register
xrt86vx38 152 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 144: r eceive l oopback c ode 5 i nterrupt e nable r egister (rlcier5) h ex a ddress : 0 x nb21 b it f unction t ype d efault d escription -o peration 7-2 reserved - - reserved 1 rxaenb r/w 0 receive loopback activation code interrupt enable this bit enables or disables the ?change in receive loopback acti - vation code? interrupt within the t1 receive framer. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block detects the receive loopback activation code. 2. whenever the receive t1 framer block no longer detects the receive loopback activation code. 0 - disables the ?change in receive loopback activation code? interrupt within the t1 receive framer. 1 - enables the ?change in receive loopback activation code? interrupt within the t1 receive framer. 0 rxdenb r/w 0 receive loopback deactivation code interrupt enable this bit enables or disables the ?change in receive loopback deactivation code? interrupt within the t1 receive framer. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block detects the receive loopback deactivation code. 2. whenever the receive t1 framer block no longer detects the receive loopback deactivation code. 0 - disables the ?change in receive loopback deactivation code? interrupt within the t1 receive framer. 1 - enables the ?change in receive loopback deactivation code? interrupt within the t1 receive framer.
xrt86vx38 153 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 145: r eceive l oopback c ode 6 i nterrupt and s tatus r egister (rlcisr6) h ex a ddress : 0 x nb22 b it f unction t ype d efault d escription -o peration 7-4 - - - reserved (for e1 mode only) 3 rxastat ro 0 receive loopback activation code state this read only bit indicates whether or not the receive t1 framer block is currently detecting the receive loopback ac tivation code, as specified in the receive loopback activation code register (rlacr) if receive loopback activation code detection is enabled. 0 = indicates that the receive t1 framer block is not currently detecting the receive loopback activation code. 1 = indicates that the receive t1 framer block is currently detecting the receive loopback activation code. 2 rxdstat ro 0 receive loopback deactivation code state this read only bit indicates whether or not the receive t1 framer block is currently detecting the receive loopback de activation code, as specified in the receive loopback deactivation code register (rldcr) if receive loop - back deactivation code detection is enabled. 0 = indicates that the receive t1 framer block is not currently detecting the receive loopback deactivation code. 1 = indicates that the receive t1 framer block is currently detecting the receive loopback deactivation code. 1 rxaint rur/ wc 0 change in receive loopback activation code interrupt status this reset-upon-read bit field indicates whether or not the ?change in receive loopback activation code? interrupt has occurred since the last read of this register. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block detects the receive loopback activation code. 2. whenever the receive t1 framer block no longer detects the receive loopback activation code. 0 = indicates that the ?change in receive loopback activation code? inter - rupt has not occurred since the last read of this register 1 = indicates that the ?change in receive loopback activation code? inter - rupt has occurred since the last read of this register 0 rxdint rur/ wc 0 change in receive loopback deactivation code interrupt status this reset-upon-read bit field indicates whether or not the ?change in receive loopback deactivation code? interrupt has occurred since the last read of this register. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block detects the receive loopback deactivation code. 2. whenever the receive t1 framer block no longer detects the receive loopback deactivation code. 0 = indicates that the ?change in receive loopback deactivation code? inter - rupt has not occurred since the last read of this register 1 = indicates that the ?change in receive loopback deactivation code? inter - rupt has occurred since the last read of this register
xrt86vx38 154 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 146: r eceive l oopback c ode 6 i nterrupt e nable r egister (rlcier6) h ex a ddress : 0 x nb23 b it f unction t ype d efault d escription -o peration 7-2 reserved - - reserved 1 rxaenb r/w 0 receive loopback activation code interrupt enable this bit enables or disables the ?change in receive loopback acti - vation code? interrupt within the t1 receive framer. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block detects the receive loopback activation code. 2. whenever the receive t1 framer block no longer detects the receive loopback activation code. 0 - disables the ?change in receive loopback activation code? interrupt within the t1 receive framer. 1 - enables the ?change in receive loopback activation code? interrupt within the t1 receive framer. 0 rxdenb r/w 0 receive loopback deactivation code interrupt enable this bit enables or disables the ?change in receive loopback deactivation code? interrupt within the t1 receive framer. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block detects the receive loopback deactivation code. 2. whenever the receive t1 framer block no longer detects the receive loopback deactivation code. 0 - disables the ?change in receive loopback deactivation code? interrupt within the t1 receive framer. 1 - enables the ?change in receive loopback deactivation code? interrupt within the t1 receive framer.
xrt86vx38 155 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 147: r eceive l oopback c ode 7 i nterrupt and s tatus r egister (rlcisr7) h ex a ddress : 0 x nb24 b it f unction t ype d efault d escription -o peration 7-4 - - - reserved (for e1 mode only) 3 rxastat ro 0 receive loopback activation code state this read only bit indicates whether or not the receive t1 framer block is currently detecting the receive loopback ac tivation code, as specified in the receive loopback activation code register (rlacr) if receive loopback activation code detection is enabled. 0 = indicates that the receive t1 framer block is not currently detecting the receive loopback activation code. 1 = indicates that the receive t1 framer block is currently detecting the receive loopback activation code. 2 rxdstat ro 0 receive loopback deactivation code state this read only bit indicates whether or not the receive t1 framer block is currently detecting the receive loopback de activation code, as specified in the receive loopback deactivation code register (rldcr) if receive loop - back deactivation code detection is enabled. 0 = indicates that the receive t1 framer block is not currently detecting the receive loopback deactivation code. 1 = indicates that the receive t1 framer block is currently detecting the receive loopback deactivation code. 1 rxaint rur/ wc 0 change in receive loopback activation code interrupt status this reset-upon-read bit field indicates whether or not the ?change in receive loopback activation code? interrupt has occurred since the last read of this register. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block detects the receive loopback activation code. 2. whenever the receive t1 framer block no longer detects the receive loopback activation code. 0 = indicates that the ?change in receive loopback activation code? inter - rupt has not occurred since the last read of this register 1 = indicates that the ?change in receive loopback activation code? inter - rupt has occurred since the last read of this register 0 rxdint rur/ wc 0 change in receive loopback deactivation code interrupt status this reset-upon-read bit field indicates whether or not the ?change in receive loopback deactivation code? interrupt has occurred since the last read of this register. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block detects the receive loopback deactivation code. 2. whenever the receive t1 framer block no longer detects the receive loopback deactivation code. 0 = indicates that the ?change in receive loopback deactivation code? inter - rupt has not occurred since the last read of this register 1 = indicates that the ?change in receive loopback deactivation code? inter - rupt has occurred since the last read of this register
xrt86vx38 156 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 148: r eceive l oopback c ode 7 i nterrupt e nable r egister (rlcier7) h ex a ddress : 0 x nb25 b it f unction t ype d efault d escription -o peration 7-2 reserved - - reserved 1 rxaenb r/w 0 receive loopback activation code interrupt enable this bit enables or disables the ?change in receive loopback acti - vation code? interrupt within the t1 receive framer. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block detects the receive loopback activation code. 2. whenever the receive t1 framer block no longer detects the receive loopback activation code. 0 - disables the ?change in receive loopback activation code? interrupt within the t1 receive framer. 1 - enables the ?change in receive loopback activation code? interrupt within the t1 receive framer. 0 rxdenb r/w 0 receive loopback deactivation code interrupt enable this bit enables or disables the ?change in receive loopback deactivation code? interrupt within the t1 receive framer. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block detects the receive loopback deactivation code. 2. whenever the receive t1 framer block no longer detects the receive loopback deactivation code. 0 - disables the ?change in receive loopback deactivation code? interrupt within the t1 receive framer. 1 - enables the ?change in receive loopback deactivation code? interrupt within the t1 receive framer.
xrt86vx38 157 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 149: d ata l ink s tatus r egister 3 (dlsr3) h ex a ddress : 0 x nb26 b it f unction t ype d efault d escription -o peration 7 msg type rur/ wc 0 hdlc3 message type identifier this read only bit indicates the type of data link message received by receive hdlc 3 controller. two types of data link messages are supported within the xrt86vx38 devic e: message oriented signaling (mos) or bit-oriented signalling (bos). 0 = indicates bit-oriented signaling (bos) type data link message is received 1 = indicates message oriented signaling (mos) type data link mes - sage is received 6 txsot rur/ wc 0 transmit hdlc3 controller start of transmission (txsot) inter - rupt status this reset-upon-read bit indicates whether or not the ?transmit hdlc3 controller start of transmission (txsot) ?interrupt has occurred since the last read of this register. transmit hdlc3 controller will declare this interrupt when it has started to transmit a data link mes - sage. for sending large hdlc messages, start loading the next avail - able buffer once this interrupt is detected. 0 = transmit hdlc3 controller start of transmission (txsot) interrupt has not occurred since the last read of this register 1 = transmit hdlc3 controller start of transmission interrupt (txsot) has occurred since the last read of this register. 5 rxsot rur/ wc 0 receive hdlc3 controller start of reception (rxsot) interrupt status this reset-upon-read bit indicates whether or not the receive hdlc3 controller start of reception (rxsot) interrupt has occurred since the last read of this register. receive hdlc3 controller will declare this interrupt when it has started to receive a data link mes - sage. 0 = receive hdlc3 controller start of reception (rxsot) interrupt has not occurred since the last read of this register 1 = receive hdlc3 controller start of reception (rxsot) interrupt has occurred since the last read of this register 4 txeot rur/ wc 0 transmit hdlc3 controller end of transmission (txeot) interrupt status this reset-upon-read bit indicates whether or not the transmit hdlc3 controller end of transmission (txeot) interrupt has occurred since the last read of this register. transmit hdlc3 controller will declare this interrupt when it has completed its transmission of a data link message. for sending large hdlc messages, it is critical to load the next available buffer before this interrupt occurs. 0 = transmit hdlc3 controller end of transmission (txeot) interrupt has not occurred since the last read of this register 1 = transmit hdlc3 controller end of transmission (txeot) interrupt has occurred since the last read of this register
xrt86vx38 158 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description 3 rxeot rur/ wc 0 receive hdlc3 controller end of reception (rxeot) interrupt status this reset-upon-read bit indicates whether or not the receive hdlc3 controller end of reception (rxeot) interrupt has occurred since the last read of this register. receive hdlc3 controller will declare this interrupt once it has co mpletely received a full data link message, or once the buffer is full. 0 = receive hdlc3 controller end of reception (rxeot) interrupt has not occurred since the last read of this register 1 = receive hdlc3 controller end of reception (rxeot) interrupt has occurred since the last read of this register 2 fcs error rur/ wc 0 fcs error interrupt status this reset-upon-read bit indicates whether or not the fcs error inter - rupt has occurred since the last read of this register. receive hdlc3 controller will declare this interrupt when it has detected the fcs error in the most recently received data link message. 0 = fcs error interrupt has not occurre d since the last read of this reg - ister 1 = fcs error interrupt has occurred since the last read of this register 1 rx abort rur/ wc 0 receipt of abort sequence interrupt status this reset-upon-read bit indicates whether or not the receipt of abort sequence interrupt has occurred sinc e last read of this register. receive hdlc3 controller will declare this interrupt if it detects the abort sequence (i.e. a string of seven (7) consecutive 1?s) in the incoming data link channel. 0 = receipt of abort sequence interrupt has not occurred since last read of this register 1 = receipt of abort sequence interrupt has occurred since last read of this register 0 rxidle rur/ wc 0 receipt of idle sequence interrupt status this reset-upon-read bit indicates whether or not the receipt of idle sequence interrupt has occurred since the last read of this register. the receive hdlc3 controller will declare this interrupt if it detects the flag sequence octet (0x7e) in the incoming data link channel. if rxi - dle "and" rxeot occur together, then the entire hdlc message has been received. 0 = receipt of idle sequence interrupt has not occurred since last read of this register 1 = receipt of idle sequence interrupt has occurred since last read of this register. t able 149: d ata l ink s tatus r egister 3 (dlsr3) h ex a ddress : 0 x nb26 b it f unction t ype d efault d escription -o peration
xrt86vx38 159 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 150: d ata l ink i nterrupt e nable r egister 3 (dlier3) h ex a ddress : 0 x nb27 b it f unction t ype d efault d escription -o peration 7 reserved - - reserved 6 txsot enb r/w 0 transmit hdlc3 controller start of transmission (txsot) interrupt enable this bit enables or disables the ?transmit hdlc3 controller start of transmission (txsot) ?interrupt within the xrt86vx38 device. once this interrupt is enabled, the transmit hdlc3 controller will generate an interrupt when it has started to transmit a data link mes - sage. 0 = disables the transmit hdlc3 controller start of transmission (txsot) interrupt. 1 = enables the transmit hdlc3 controller start of transmission (txsot) interrupt. 5 rxsot enb r/w 0 receive hdlc3 controller start of reception (rxsot) interrupt enable this bit enables or disables the ?receive hdlc3 controller start of reception (rxsot) ?interrupt within the xrt86vx38 device. once this interrupt is enabled, the receive hdlc3 controller will generate an interrupt when it has started to receive a data link message. 0 = disables the receive hdlc3 controller start of reception (rxsot) interrupt. 1 = enables the receive hdlc3 controller start of reception (rxsot) interrupt. 4 txeot enb r/w 0 transmit hdlc3 controller end of transmission (txeot) inter - rupt enable this bit enables or disables the ?transmit hdlc3 controller end of transmission (txeot) ?interrupt within the xrt86vx38 device. once this interrupt is enabled, the transmit hdlc3 controller will generate an interrupt when it has finished transmitting a data link message. 0 = disables the transmit hdlc3 controller end of transmission (txeot) interrupt. 1 = enables the transmit hdlc3 controller end of transmission (txeot) interrupt. 3 rxeot enb r/w 0 receive hdlc3 controller end of reception (rxeot) interrupt enable this bit enables or disables the ?receive hdlc3 controller end of reception (rxeot) ?interrupt within the xrt86vx38 device. once this interrupt is enabled, the receive hdlc3 controller will generate an interrupt when it has finished receiving a complete data link mes - sage. 0 = disables the receive hdlc3 controller end of reception (rxeot) interrupt. 1 = enables the receive hdlc3 controller end of reception (rxeot) interrupt.
xrt86vx38 160 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description 2 fcs err enb r/w 0 fcs error interrupt enable this bit enables or disables the ?received fcs error ?interrupt within the xrt86vx38 device. once this interrupt is enabled, the receive hdlc3 controller will ge nerate an interrupt when it has detected the fcs error within the incoming data link message. 0 = disables the ?receive fcs error? interrupt. 1 = enables the ?receive fcs error? interrupt. 1 rxabort enb r/w 0 receipt of abort sequence interrupt enable this bit enables or disables the ?receipt of abort sequence? inter - rupt within the xrt86vx38 device. once this interrupt is enabled, the receive hdlc3 controller will generate an interrupt when it has detected the abort sequence (i.e. a string of seven (7) consecutive 1?s) within the incoming data link channel. 0 = disables the ?receipt of abort sequence? interrupt. 1 = enables the ?receipt of abort sequence? interrupt. 0 rxidle enb r/w 0 receipt of idle sequence interrupt enable this bit enables or disables the ?receipt of idle sequence? interrupt within the xrt86vx38 device. once this interrupt is enabled, the receive hdlc3 controller will ge nerate an interrupt when it has detected the idle sequence octet (i.e. 0x7e) within the incoming data link channel. 0 = disables the ?receipt of idle sequence? interrupt. 1 = enables the ?receipt of idle sequence? interrupt. t able 150: d ata l ink i nterrupt e nable r egister 3 (dlier3) h ex a ddress : 0 x nb27 b it f unction t ype d efault d escription -o peration
xrt86vx38 161 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 151: ss7 s tatus r egister for lapd3 (ss7sr3) h ex a ddress : 0 x nb28 b it f unction t ype d efault d escription -o peration 0 ss7_3_status rur/ wc 0 ss7 interrupt status fo r lapd controller 3 this reset-upon-read bit field indicates whether or not the ?ss7? interrupt has occurred since the last read of this register. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt when the received lapd message is more than 276 bytes in length. 0 = indicates that the ?ss7? interrupt has not occurred since the last read of this register 1 = indicates that the ?ss7? interrupt has occurred since the last read of this register t able 152: ss7 e nable r egister for lapd3 (ss7er3) h ex a ddress : 0 x nb29 b it f unction t ype d efault d escription -o peration 0 ss7_3_enb r/w 0 ss7 interrupt enable fo r lapd controller 3 this bit enables or disables the ?ss7? interrupt within the lapd controller 3. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt when the received lapd message is more than 276 bytes in length. 0 - disables the ?ss7? interrupt within the lapd controller 3. 1 - enables the ?ss7? interrupt within the lapd controller 3.
xrt86vx38 162 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 153: c ustomer i nstallation a larm s tatus r egister (ciasr) h ex a ddress : 0 x nb40 b it f unction t ype d efault d escription -o peration [7:6] reserved - - reserved 5 rxais-ci_state ro 0 receive alarm indication signal-custo mer installation (ais-ci) state this read only bit field indicates whether or not the receive t1 framer is currently detecting the alarm indication signal-customer installation (ais- ci) condition. alarm indication signal-customer installation (ais-ci) is intended for use in a network to differentiate between an issue within the network or the cus - tomer installation (ci). ais-ci is an all ones signal with an embedded signature of 01111100 11111111 (right-to left) which recurs at 386 bit intervals in-the ds-1 signal. 0 = indicates the receive t1 framer is currently not detecting the ais-ci condition 1 = indicates the receive t1 framer is currently detecti ng the ais-ci condi - tion n ote : this bit only works if ais-ci detection is enabled (register 0xn11c) 4 rxrai-ci_state ro 0 rx rai-ci state this read only bit field indicates whether or not the receive t1 framer is currently declaring the remote alarm indication - customer installation (rai-ci) condition. (this is for t1 esf framing mode only) remote alarm indication - customer installation (rai-ci) is intended for use in a network to differentiate between an issue within the network or the cus - tomer installation (ci). rai-ci is a repetitive pattern with a peri od of 1.08 seconds. it is comprised of 0.99 seconds of rai message (00000000 11111111 right-to-left) and a 90 ms of rai-ci signature (00111110 11111111 right to left) to form a rai-ci signal. 0 = indicates the receive t1 framer is currently not detecting the rai-ci condition 1 = indicates the receive t1 framer is currently detecting the rai-ci condi - tion n ote : this bit only works if rai-ci detection is enabled (register 0xn11c) [3:2] reserved - - reserved
xrt86vx38 163 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 1 rxais-ci rur/ wc 0 change in receive ais-ci condition interrupt status this reset-upon-read bit field indicates whether or not the ?change in ais- ci condition? interrupt within the t1 receive framer block has occurred since the last read of this register. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer bl ock detects the ais-ci condition. 2. whenever the receive t1 framer bl ock clears the ais-ci condition 0 = indicates the ?change in ais-ci condition? interrupt has not occurred since the last read of this register 1 = indicates the ?change in ais-ci condition? interrupt has occurred since the last read of this register 0 rxrai-ci rur/ wc 0 change in receive rai-ci condition interrupt status this reset-upon-read bit field indicates whether or not the ?change in rai- ci condition? interrupt within the t1 receive framer block has occurred since the last read of this register. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block detects the rai-ci condition. 2. whenever the receive t1 framer block clears the rai-ci condition 0 = indicates the ?change in rai-ci condition? interrupt has not occurred since the last read of this register 1 = indicates the ?change in rai-ci condition? interrupt has occurred since the last read of this register t able 154: c ustomer i nstallation a larm s tatus r egister (ciaier) h ex a ddress : 0 x nb41 b it f unction t ype d efault d escription -o peration 1 rxais-ci_enb r/w 0 change in receive ais-ci condition interrupt enable this bit enables or disables the ?change in ais-ci condition? interrupt within the t1 receive framer block. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer bl ock detects the ais-ci condition. 2. whenever the receive t1 framer block clears the ais-ci condition 0 - disables the ?change in ais-ci condition? interrupt. 1 - enables the ?change in ais-ci condition? interrupt. 0 rxrai-ci_enb r/w 0 change in receive rai-ci condition interrupt enable this bit enables or disables the ?change in rai-ci condition? interrupt within the t1 receive framer block. if this interrupt is enabled, then the receive t1 framer block will generate an interrupt in response to either one of the following conditions. 1. whenever the receive t1 framer block detects the rai-ci condition. 2. whenever the receive t1 framer block clears the ais-ci condition 0 - disables the ?change in rai-ci condition? interrupt. 1 - enables the ?change in rai-ci condition? interrupt. t able 153: c ustomer i nstallation a larm s tatus r egister (ciasr) h ex a ddress : 0 x nb40 b it f unction t ype d efault d escription -o peration
xrt86vx38 164 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description bit 7 - receive fdl match 3 event this bit is set when the receive fdl message is equal to the rfdl match 3 message, and filter validation has occured. } 0 - no match } 1 - match 3 bit 6 - receive fdl match 2 event this bit is set when the receive fdl message is equal to the rfdl match 2 message, and filter validation has occured. } 0 - no match } 1 - match 2 bit 5 - boc clear event (loss of boc) this bit is set when 3 or more consecutive non-boc messages occur (non-boc means that the message meets the ?0xxxxxx011111111? framing format, but does not contain a valid boc). } 0 - no change } 1 - boc cleared bit 4 - rfdl abor t detect event this bit is set when nine consecutive ones are detected within the fdl bits. } 0 - normal } 1 - rfdl abort bit 3 - rfdl register full event (receive start of transfer) this bit is set when the rfdl register is fu ll. this register is not gated by the filter. } 0 - not full }1 - full t able 155: t1 boc i nterrupt s tatus r egister (bocisr 0 x nb70 h ) bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 rmtch3 rmtch2 bocc rfdlad rfdlf tfdle rmtch1 rboc rur rur rur rur rur rur rur rur 0 0 0 0 0 0 0 0
xrt86vx38 165 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 bit 2 - tfdl register empty event (transmit end of transfer) this bit is set when the tfdl register has been emptied according to amount of repetitions programmed into the txbyte count register 0xn178h. this alarm is meant to be an indicator of a complete boc transmi ssion for system alert or to initiate a response for future processing. } 0 - not emptied }1 - emptied bit 1 - receive fdl match 1 event this bit is set when the receive fdl message is equal to the rfdl match 1 message, and filter validation has occured. } 0 - no match } 1 - match 1 bit 0 - receive boc detector change of status this bit is set to 1 any time a change has occured with the rfdl message. this alarm will not be set unless the filter setting has been satisfied. } 0 - no change } 1 - change of status
xrt86vx38 166 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description bit 7 - receive fdl match 3 event this bit is used to enable the rfdl match 3 message interrupt. } 0 - disabled } 1 - interrupt enabled bit 6 - receive fdl match 2 event this bit is used to enable the rfdl match 2 message interrupt. } 0 - disabled } 1 - interrupt enabled bit 5 - boc clear event this bit is used to enable the boc clear event interrupt. } 0 - disabled } 1 - interrupt enabled bit 4 - rfdl abor t detect event this bit is used to enable the rfdl abort dete ct event interrupt. } 0 - disabled } 1 - interrupt enabled bit 3 - rfdl register full event this bit is used to enable the rfdl full interrupt. } 0 - disabled } 1 - interrupt enabled bit 2 - tfdl register empty event this bit is used to enable the tfdl empty interrupt. } 0 - disabled } 1 - interrupt enabled bit 1 - receive fdl match 1 event this bit is used to enable the rfdl match 1 message interrupt. } 0 - disabled } 1 - interrupt enabled bit 0 - receive boc detector change of status this bit is used to enable the boc detector change of status interrupt. } 0 - disabled } 1 - interrupt enabled t able 156: t1 boc i nterrupt e nable r egister (bocier 0 x nb71 h ) bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 rmtch3 rmtch2 bocc rfdlad rfdlf tfdle rmtch1 rboc r/w r/w r/w r/w r/w r/w r/w r/w 0 0 0 0 0 0 0 0
xrt86vx38 167 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 bit 7 - reserved bit 6 - unstable ssm message interrupt status this bit will be set to ?1? anytime th e receive ssm message has changed from its previous value, if the ssm message was valid. therefore, this interrupt is only ac tive once the boc has received a valid ssm message. this register is reset upon read. } 0 - no change in ssm } 1 - change in ssm bits [5:0] - reserved t able 157: t1 boc u nstable i nterrupt s tatus r egister (bocuisr 0 x nb74 h ) bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 reserved unstable reserved rur rur rur rur rur rur rur rur 0 0 0 0 0 0 0 0
xrt86vx38 168 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description bit 7 - reserved bit 6 - unstable ssm message interrupt enable this bit is used to enable the unstable ssm message interrupt. unstable is defined as anytime the receive ssm message has changed from its previous value, if t he ssm message was valid. ther efore, this interrupt is only active once the boc has received a valid ssm message. } 0 - disabled } 1 - interrupt enabled bits [5:0] - reserved t able 158: t1 boc u nstable i nterrupt e nable r egister (bocuier 0 x nb75 h ) bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 reserved unstable reserved r/w r/w r/w r/w r/w r/w r/w r/w 0 0 0 0 0 0 0 0
xrt86vx38 169 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 2.0 line interface unit (liu section) registers t able 159: liu c hannel c ontrol r egister 0 (liuccr0) h ex a ddress : 0 x 0fn0 b it f unction t ype d efault d escription -o peration 7 qrss_n/ prbs_n r/w 0 qrss/prbs select bits these bits are used to select between qrss and prbs. 0 = prbs_n (2 15 - 1) 1 = qrss_n (2 20 - 1) 6 prbs_rx_n/ prbs_ tx _n r/w 0 prbs receive/transmit select: this bit is used to select where th e output of the prbs generator is directed if prbs generation is enabled. 0 = normal operation - prbs generator is output on ttip and tring if prbs generation is enabled. 1 = prbs generator is output on rpos and rclk. 5 rxon_n r/w 0 receiver on: this bit permits the user to either turn on or turn off the receive sec - tion of xrt86vx38. if the user turns on the receive section, then xrt86vx38 will begin to receive the incoming data-stream via the rtip and rring input pins. conversely, if the user turns off t he receive section, then the entire receive section except the mclkin phase locked loop (pll) will be powered down. 0 = shuts off the receive section of xrt86vx38. 1 = turns on the receive section of xrt86vx38. pbrs generator tx ttip tring + - bit 6 = "0" pbrs generator rx rpos rneg + - bit 6 = "1"
xrt86vx38 170 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description 4-0 eqc[4:0] r/w 00000 equalizer control [4:0]: these bits are used to control the transmit pulse shaping, transmit line build-out (lbo) and receive sensitivity level. the transmit pulse shape can be controlled by adjusting the trans - mit line build-out settings for different cable length in t1 mode. transmit pulse shape can also be controlled by using the arbitrary mode, where users can specify the amplitude of the pulse shape by using the 8 arbitrary pulse segments provided in the liu registers (0xnf08-0xnf0f), where n is the channel number. the xrt86vx38 device supports both long haul and short haul applications which can also be selected using the eqc[4:0] bits. table 160 .presents the corresponding transmit line build out and receive sensitivity settings using different combinations of these five eqc[4:0] bits. t able 159: liu c hannel c ontrol r egister 0 (liuccr0) h ex a ddress : 0 x 0fn0 b it f unction t ype d efault d escription -o peration
xrt86vx38 171 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 160: e qualizer c ontrol and t ransmit l ine b uild o ut eqc[4:0] t1 m ode /r eceive s ensitivity t ransmit lbo c able 0xn0h t1 long haul/36db 0db 100 ?? tp 0xn1h t1 long haul/36db -7.5db 100 ?? tp 0xn2h t1 long haul/36db -15db 100 ?? tp 0xn3h t1 long haul/36db -22.5db 100 ?? tp 0xn4h t1 long haul/45db 0db 100 ?? tp 0xn5h t1 long haul/45db -7.5db 100 ?? tp 0xn6h t1 long haul/45db -15db 100 ?? tp 0xn7h t1 long haul/45db -22.5db 100 ?? tp 0xn8h t1 short haul/15db 0 to 133 feet (0.6db) 100 ?? tp 0xn9h t1 short haul/15db 133 to 266 feet (1.2db) 100 ?? tp 0xnah t1 short haul/15db 266 to 399 feet (1.8db) 100 ?? tp 0xnbh t1 short haul/15db 399 to 533 feet (2.4db) 100 ?? tp 0xnch t1 short haul/15db 533 to 655 feet (3.0db) 100 ?? tp 0xndh t1 short haul/15db arbitrary pulse 100 ?? tp 0xneh t1 gain mode/29db 0 to 133 feet (0.6db) 100 ?? tp 0xnfh t1 gain mode/29db 133 to 266 feet (1.2db) 100 ?? tp 0x10h t1 gain mode/29db 266 to 399 feet (1.8db) 100 ?? tp 0x11h t1 gain mode/29db 399 to 533 feet (2.4db) 100 ?? tp 0x12h t1 gain mode/29db 533 to 655 feet (3.0db) 100 ?? tp 0x13h t1 gain mode/29db arbitrary pulse 100 ?? tp 0x14h t1 gain mode/29db 0db 100 ?? tp 0x15h t1 gain mode/29db -7.5db 100 ?? tp 0x16h t1 gain mode/29db -15db 100 ?? tp 0x17h t1 gain mode/29db -22.5db 100 ?? tp 0x18h e1 long haul/36db itu g.703 75 ? coax 0x19h e1 long haul/36db itu g.703 120 ? tp 0x1ah e1 long haul/45db itu g.703 75 ? coax 0x1bh e1 long haul/45db itu g.703 120 ? tp 0x1ch e1 short haul/15db itu g.703 75 ? coax 0x1dh e1 short haul/15db itu g.703 120 ? tp 0x1eh e1 gain mode/29db itu g.703 75 ? coax 0x1fh e1 gain mode/29db itu g.703 120 ? tp
xrt86vx38 172 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 161: liu c hannel c ontrol r egister 1 (liuccr1) h ex a ddress : 0 x 0fn1 b it f unction t ype d efault d escription -o peration 7 rxtsel_n r/w 0 receiver termination select: upon power up, the receivers are in ?high? impedance. the receive termination can be selected by setting this bit according to the fol - lowing table: 6 txtsel_n r/w 0 transmit termination select: this bit is used to select between internal termination or ?high? impedance modes for the t1 transmitter according to the following table: 5-4 tersel[1:0] r/w 00 termination impeda nce select [1:0]: these bits are used to control t he transmit and receive termination impedance when the liu block is configured in internal termination mode. in internal termination mode, (i.e., txtsel = ?1? and rxtsel = ?1?), internal transmit and receive termination can be selected according to the following table: n ote : in the internal termination mode, the transmitter output should be ac coupled to the transformer. 3 rxjasel_n r/w 0 receive jitter attenuator enable this bit permits the user to enable or disable the jitter attenuator in the receive path within the xrt86vx38 device. 0 = disables the jitter attenuator to operate in the receive path within the receive t1 liu block. 1 = enables the jitter attenuator to operate in the receive path within the receive t1 liu block. rxtsel rx termination 0 1 "high" impedance internal txtsel tx termination 0 1 "high" impedance internal tersel1 tersel0 0 0 0 1 1 0 1 1 internal transmit and receive termination 100 ? 110 ? 75 ? 120 ?
xrt86vx38 173 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 2 txjasel_n r/w 0 transmit jitter a ttenuator enable this bit permits the user to enable or disable the jitt er attenuator in the transmit path within the xrt86vx38 device. 0 = disables the jitter attenuator to operate in the transmit path within the transmit t1 liu block. 1 = enables the jitter attenuator to operate in the transmit path within the transmit t1 liu block. 1 jabw_n r/w 0 jitter attenuator bandwidth select: in t1 mode, the jitter attenuator bandwidth is always 3hz, and this bit has no effect on the jitter at tenuator bandwidth. the fifos (bit d0 of this register) will be used to select the fifo size, according to the table below. 0 fifos_n r/w 0 fifo size select: see table of bit d1 above for the function of this bit. t able 161: liu c hannel c ontrol r egister 1 (liuccr1) h ex a ddress : 0 x 0fn1 b it f unction t ype d efault d escription -o peration 0 1 0 1 0 1 0 1 fifos_n bit d0 0 0 1 1 0 0 1 1 jabw bit d1 t1 t1 t1 t1 e1 e1 e1 e1 mode 32 64 32 64 32 64 64 64 fifo size 3 3 3 3 10 10 1.5 1.5 ja b-w hz
xrt86vx38 174 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 162: liu c hannel c ontrol r egister 2 (liuccr2) h ex a ddress : 0 x 0fn2 b it f unction t ype d efault d escription -o peration 7 invqrss_n r/w 0 invert qrss pattern: this bit inverts the output prbs/qrss pattern if the liu block is configured to transmit a prbs/qrss pattern. 0 = the liu will not invert the output prbs/qrss pattern 1 = the liu will invert the output prbs/qrss pattern 6-4 txtest[2:0] r/w 000 transmit test pattern [2:0] : these bits are used to configure the transmit t1 liu block to gen - erate and transmit test patterns according to the following table. use of these bits automat ically places the liu section in single rail mode. when this happens, the fr amer section must be placed in single rail mode in reg 0xn101. tdqrss (transmit/detect quasi-random signal): qrss pattern is a 2 20 -1 pseudo-random bit sequence (prbs) with no more than 14 consecutive zeros. taos (transmit all ones): whenever the user implements this configuration setting, the trans - mit t1 liu block will ignore the data that it is accepting from the transmit t1 framer block (as well as the upstream system-side ter - minal equipment) and overwrite this data with the all ones pattern. tluc (transmit network loop-up code): the transmit t1 liu block will ge nerate and transmit the network loop-up code of ?00001? to the line for the selected channel num - ber n. when network loop-up code is being transmitted, the xrt86vx38 will ignore the ?automatic loop-code detection and remote loop- back activation? (nlcde1 =?1?, nlcde0 =?1? of register 0xnf03) in order to avoid activating remote digital loop-back automatically when the remote terminal responds to the loop-back request. tldc (transmit network loop-down code): the transmit t1 liu block will ge nerate and transmit the network loop-down code of ?001? to the line for the selected channel num - ber n. 0 0 0 1 1 0 1 1 1 1 1 1 x x 0 no pattern tdqrss taos tluc test pattern tldc txtest1 txtest0 txtest2
xrt86vx38 175 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 3 txon_n r/w 0 transmitter on: this bit permits the user to either turn on or turn off the transmit driver of xrt86vx38. if the user turns on the transmit driver, then xrt86vx38 will begin to transmit t1 data (on the line) via the ttip and tring output pins. conversely, if the user turns off the transmit driver, then the ttip and tring output pins will be tri-stated. 0 = shuts off the transmit driver associated with the xrt86vx38 device and tri-states the ttip and tring output pins. 1 = turns on the transmit driver associated with the xrt86vx38 device. n ote : if the user wishes to exercise software control over the state of the transmit driver of the xrt86vx38, then it is imperative that the user pull the txon pin to a logic ?high? level. 2-0 loop2_n r/w 000 loop-back control [2:0]: these bits control the loop-back mo des of the liu section, accord - ing to the table below. t able 162: liu c hannel c ontrol r egister 2 (liuccr2) h ex a ddress : 0 x 0fn2 b it f unction t ype d efault d escription -o peration loop2 0 1 1 1 1 loop1 x 0 0 1 1 loop0 x 0 1 0 1 loop-back mode no loop-back dual loop-back analog loop-back remote loop-back digital loop-back
xrt86vx38 176 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 163: liu c hannel c ontrol r egister 3 (liuccr3) h ex a ddress : 0 x 0fn3 b it f unction t ype d efault d escription -o peration 7-6 nlcde[1:0] r/w 00 network loop code detection enable [1:0]: these bits are used to control the loop-code detection on the receive path, according to the table below. this part must be in sin - gle rail mode to detect. . loop-up code detection enable: the xrt86vx38 is configured to monitor the receive data for the loop-up code pattern (i.e. a string of four ?0?s followed by one ?1? pattern). when the presence of the ?00001? pattern is detected for more than 5 seconds, the status of the nlcd bit (bit 3 of register 0xnf05) is set to ?1? and if the nlcd interrupt is enabled (bit 3 of register 0xnf04), an interrupt will be generated. loop-down code detection enable: the xrt86vx38 is configured to monitor the receive data for the loop-down code pattern (i.e. a string of two ?0?s followed by one ?1? pattern). when the presence of the ?001? pattern is detected for more than 5 seconds, the status of the nlcd bit (bit 3 of register 0xnf05) is set to ?1? and if the nlcd interrupt is enabled (bit 3 of register 0xnf04), an interrupt will be generated. automatic loop-up code detection and remote loop back activation enable: when this mode is enabled, the state of the nlcd bit (bit 3 of regis - ter 0xnf05) is reset to ?0? and the xrt86vx38 is configured to monitor the receive data for the loop-up code. if the ?00001? pattern is detected for longer than 5 sec onds, then the nlcd bit (bit 3 of register 0xnf05) is set ?1?, and remote loop-back is activated. once the remote loop-back is activated, the xrt86vx38 is auto - matically programmed to monitor the receive data for the loop- down code. the nlcd bit stays set even after the chip stops receiv - ing the loop-up code. the remote loop-back condition is removed only when the xrt86vx38 receives the loop-down code for more than 5 seconds or if the automatic loop-code detection mode is terminated. 5-2 reserved r/w 0 this bit is not used nlcde[1:0] n etwork l oop c ode d etection e nable 00 disables loop code detection 01 enables loop-up code detection on the receive path. 10 enables loop-down code detection on the receive path. 11 enables automatic loop-up code detection on the receive path and remote loop-back activation upon detecting loop-up code.
xrt86vx38 177 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 1 insber_n r/w 0 insert bit error: this bit is used to insert a single bit error on the transmitter of the t1 liu block. when the t1 liu block is config ured to transmit and detect the qrss pattern, (i.e., txtest[2:0] bits set to ?b100?), a ?0? to ?1? tran - sition of this bit will insert a bit error in the transmitted qrss pattern of the selected channel number n. the state of this bit is sampled on the rising edge of the respective tclk_n. n ote : to ensure the insertion of bit error, a ?0? should be written in this bit location before writing a ?1?. 0 reserved r/w 0 this bit is not used t able 163: liu c hannel c ontrol r egister 3 (liuccr3) h ex a ddress : 0 x 0fn3 b it f unction t ype d efault d escription -o peration
xrt86vx38 178 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 164: liu c hannel c ontrol i nterrupt e nable r egister (liuccier) h ex a ddress : 0 x 0fn4 b it f unction t ype d efault d escription -o peration 7 reserved ro 0 this bit is not used 6 dmoie_n r/w 0 change of transmit dmo (drive monitor output) condition inter - rupt enable: this bit permits the user to either enable or disable the ?change of transmit dmo condition? interrupt. if the user enables this interrupt, then the xrt86vx38 device will generate an interrupt any time when either one of the following events occur. 1. whenever the transmit section toggl es the dmo status bit (bit 6 or register 0xnf05) to ?1?. 2. whenever the transmit section toggl es the dmo status bit (bit 6 or register 0xnf05) to ?0?. 0 ? disables the ?change in the dmo condition? interrupt. 1 ? enables the ?change in the dmo condition? interrupt. 5 flsie_n r/w 0 fifo limit status interrupt enable: this bit permits the user to either enable or disable the ?fifo limit sta - tus? interrupt. if the user enables this interrupt, then the xrt86vx38 device will generate an interrupt w hen the jitter attenuator read/write fifo pointers are within +/- 3 bits. 0 = disables the ?fifo limit status? interrupt 1 = enables the ?fifo limit status? interrupt 4 reserved - - this bit is not used. 3 nlcdie_n r/w 0 change in network loop-code detection interrupt enable: this bit permits the user to either enable or disable the ?change in net - work loop-code detection? interrupt. if the user enables this interrupt, then the xrt86vx38 device will generate an interrupt any time when either one of the following events occur. 1. whenever the receive section (within xrt86vx38) detects the network loop-code (loop-up or loop-down depending on which loop-code the receive liu is configured to detect). 2. whenever the receive section (within xrt86vx38) no longer detects the network loop-code (loop-up or loop-down depending on which loop-code the receive liu is configured to detect). 0 ? disables the ?change in networ k loop-code detection? interrupt. 1 ? enables the ?change in network loop-code detection? interrupt. 2 reserved - - this bit is not used
xrt86vx38 179 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 n ote : register 0xnf04, 0xnf05 and 0xnf06 only work if the liu is placed in single rail mode. if done so, the framer block must also be placed in single rail mode in register 0xn101. 1 rlosie_n r/w 0 change of the receive los (loss of signal) defect condition inter - rupt enable: this bit permits the user to either enable or disable the ?change of the receive los defect condition? interr upt. if the user enables this inter - rupt, then the xrt86vx38 device will generate an interrupt any time when either one of the following events occur. 1. whenever the receive section (within xrt86vx38) declares the los defect condition. 2. whenever the receive section ( within xrt86vx38) clears the los defect condition. 0 ? disables the ?change in the lo s defect condition? interrupt. 1 ? enables the ?change in the los defect condition? interrupt. 0 qrpdie_n r/w 0 change in qrss pattern de tection interr upt enable: this bit permits the user to either enable or disable the ?change in qrss pattern detection? interrupt. if the user enables this interrupt, then the xrt86vx38 device will generate an interrupt any time when either one of the following events occur. 1. whenever the receive section (within xrt86vx38) detects the qrss pattern. 2. whenever the receive section (within xrt86vx38) no longer detects the qrss pattern. 0 ? disables the ?change in qrss pattern detection? interrupt. 1 ? enables the ?change in qrss pattern detection? interrupt. t able 164: liu c hannel c ontrol i nterrupt e nable r egister (liuccier) h ex a ddress : 0 x 0fn4 b it f unction t ype d efault d escription -o peration
xrt86vx38 180 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 165: liu c hannel c ontrol s tatus r egister (liuccsr) h ex a ddress : 0 x 0fn5 b it f unction t ype d efault d escription -o peration 7 reserved ro 0 6 dmo_n ro 0 driver monitor output (dmo) status: this read-only bit indicates whether or not the transmit section is currently declaring the dmo alarm condition. the transmit section will check the transmit output t1 line signal for bipolar pulses via the ttip and tring output signals. if the transmit section were to detect no bipolar signal for 128 consecu - tive bit-periods, then it will declare the transmit dmo alarm condi - tion. this particular alarm can be used to check for fault conditions on the transmit output line signal path. the transmit section will clear the transmit dmo alarm condition the instant that it detects some bipolar activity on the transmit out - put line signal. 0 = indicates that the transmit section of xrt86vx38 is not cur - rently declaring the transmit dmo alarm condition. 1 = indicates that the transmit section of xrt86vx38 is currently declaring the transmit dmo alarm condition. n ote : if the dmo interrupt is enabled (dmoie - bit d6 of register 0xnf04), any transition on this bit will generate an interrupt. 5 fls_n ro 0 fifo limit status: this read-only bit indicates whether or not the xrt86vx38 is currently declaring the fifo limit status. this bit is set to a ?1? to indicate that the jitte r attenuator read/write fifo pointers are within +/- 3 bits. 0 = indicates that the xrt86vx38 is not currently declaring the fifo limit status. 1 = indicates that the xrt86vx38 is currently declaring the fifo limit status. n ote : if the fifo limit status interrupt is enabled, (flsie bit - bit d5 of register 0xnf04), any transition on this bit will generate an interrupt. 4 reserved - 0 this bit is not used
xrt86vx38 181 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 3 nlcd_n ro 0 network loop-code detection status bit: this bit operates differently in t he manual or the automatic network loop-code detection modes. manual loop-up code detection mode (.i.e if nlcde1 = ?0? and nlcde0 = ?1?), this bit gets set to ?1? as soon as the loop-up code (?00001?) is detected in the receive data for longer than 5 seconds. this bit stays high as long as the receive t1 liu block detects the presence of the loop-up code in the receive data and it is reset to ?0? as soon as it stops receiving the loop-up code. if the nlcd interrupt is enabled, the xrt86vx38 will initiate an interrupt on every transitio n of the nlcd status bit. manual loop-down code detection mode (i.e., if nlcde1 = ?1? and nlcde0 = ?0?), this bit gets set to ?1? as soon as the loop-down code (?001?) is detected in the receive data for longer than 5 seconds. this bit stays high as long as the receive t1 liu block detects the presence of the loop-down code in the receive data and it is reset to ?0? as soon as it stops receiving the loop-down code. if the nlcd interrupt is enabled, the xrt86vx38 will initiate an interrupt on every transitio n of the nlcd status bit. automatic loop-code detection mode (i.e., if nlcde1 = ?1? and nlcde0 =?1?), the state of the nlcd sta - tus bit is reset to ?0? and the xrt86vx38 is programmed to monitor the receive input data for the loop-up code. this bit is set to a ?1? to indicate that the network loop code is detected for more than 5 seconds. simultaneously, the remote loop-back condition is automatically activated and the xrt86vx38 is programmed to monitor the receive data for the network loop down code. the nlcd bit stays ?high? as long as the remote loop- back condition is in effect even if the chip stops receiving the loop- up code. remote loop-back is removed only if the xrt86vx38 detects the loop-down code ?001? pattern for longer than 5 sec - onds in the receive data. upon detecting the loop-down code ?001? pattern, the xrt86vx38 will reset the nlcd status bit and an inter - rupt will be generated if the nlcd interrupt enable bit is enabled. users can monitor the state of this bit to determine if the remote loop-back is activated. 2 reserved - 0 this bit is not used 1 rlos_n ro 0 receive loss of signal defect condition status: this read-only bit indicates whether or not the receive liu block is currently declaring t he los defect condition. 0 = indicates that the receive section is not currently declaring the los defect condition. 1 = indicates that the receive section is currently declaring the los defect condition. n ote : if the rlosie bit (bit d1 of register 0xnf04) is enabled, any transition on this bit wi ll generate an interrupt. t able 165: liu c hannel c ontrol s tatus r egister (liuccsr) h ex a ddress : 0 x 0fn5 b it f unction t ype d efault d escription -o peration
xrt86vx38 182 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description n ote : register 0xnf04, 0xnf05 and 0xnf06 only work if the liu is placed in single rail mode. if done so, the framer block must also be placed in single rail mode in register 0xn101. 0 qrpd_n ro 0 quasi-random pattern detection status: this read-only bit indicates whether or not the receive liu block is currently declaring the qrss pattern lock status. 0 = indicates that the xrt86vx38 is not currently declaring the qrss pattern lock. 1 = indicates that the xrt86vx38 is currently declaring the qrss pattern lock. n ote : if the qrpdie bit (bit d0 of register 0xnf04) is enabled, any transition on this bit wi ll generate an interrupt. t able 165: liu c hannel c ontrol s tatus r egister (liuccsr) h ex a ddress : 0 x 0fn5 b it f unction t ype d efault d escription -o peration
xrt86vx38 183 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 166: liu c hannel c ontrol i nterrupt s tatus r egister (liuccisr) h ex a ddress : 0 x 0fn6 b it f unction t ype d efault d escription -o peration 7 reserved ro 0 6 dmois_n rur/ wc 0 change of transmit dmo (dri ve monitor outp ut) condition interrupt status: this reset-upon-read bi t indicates whet her or not t he ?change of the transmit dmo condition? interr upt has occurred since the last read of this register. 0 = indicates that the ?change of the transmit dmo condition? interrupt has not occurred since t he last read of this register. 1 = indicates that the ?change of the transmit dmo condition? interrupt has occurred since the last read of this register. this bit is set to a ?1? every time when dmo_n status bit (bit 6 of register 0xnf05) has changed since the last read of this register. n ote : users can determine the current state of the ?transmit dmo condition? by reading out the content of bit 6 within register 0xnf05 5 flsis_n rur/ wc 0 fifo limit interrupt status: this reset-upon-read bit indica tes whether or not the ?fifo limit? interrupt has occurred since the last read of this register. 0 = indicates that the ?fifo limit status? interrupt has not occurred since the last read of this register. 1 = indicates that the ?fifo limi t status? interrupt has occurred since the last read of this register. this bit is set to a ?1? every ti me when fifo limit status bit (bit 5 of register 0xnf05) has changed since the last read of this register. n ote : users can determine the current state of the ?fifo limit? by reading out the content of bit 5 within register 0xnf05 4 reserved - - this bit is not used 3 nlcdis_n rur/ wc 0 change in network loop-code detection interrupt status: this reset-upon-read bit indicate s whether or not the ?change in network loop-code detection? interr upt has occurred since the last read of this register. 0 = indicates that the ?change in network loop-code detection? interrupt has not occurred since t he last read of this register. 1 = indicates that the ?change in network loop-code detection? interrupt has occurred since the last read of this register. this bit is set to a ?1? every time when nlcd status bit (bit 3 of reg - ister 0xnf05) has changed since the last read of this register. n ote : users can determine the current state of the ?network loop- code detection? by reading out the content of bit 3 within register 0xnf05 2 reserved - - this bit is not used
xrt86vx38 184 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description n ote : register 0xnf04, 0xnf05 and 0xnf06 only work if the liu is placed in single rail mode. if done so, the framer block must also be placed in single rail mode in register 0xn101. 1 rlosis_n rur/ wc 0 change of receive los (loss of signal) defect condition inter - rupt status: this reset-upon-read bi t indicates whet her or not t he ?change of the receive los defect condition? interrupt has occurred since the last read of this register. 0 = indicates that the ?change of the receive los defect condi - tion? interrupt has not occurred since the last read of this register. 1 - indicates that the ?change of the receive los defect condition? interrupt has occurred since the last read of this register. n ote : the user can determine the current state of the ?receive los defect condition? by readi ng out the contents of bit 1 (receive los defect condition status) within register 0xnf05. 0 qrpdis_n rur/ wc 0 change in quasi-random pattern detection interrupt status: this reset-upon-read bit indicate s whether or not the ?change in qrss pattern detection? interrupt has occurred since the last read of this register. 0 = indicates that the ?change in qrss pattern detection? interrupt has not occurred since the last read of this register. 1 = indicates that the ?change in qrss pattern detection? interrupt has occurred since the last read of this register. this bit is set to a ?1? every time when qrpd status bit (bit 0 of reg - ister 0xnf05) has changed since the last read of this register. n ote : users can determine the current state of the ?qrss pattern detection? by reading out the content of bit 0 within register 0xnf05 t able 167: liu c hannel c ontrol c able l oss r egister (liuccccr) h ex a ddress : 0 x 0fn7 b it f unction t ype d efault d escription -o peration 7 reserved ro 0 6 reserved ro 0 5-0 clos[5:0] ro 0 cable loss [5:0]: these bits represent the six bit re ceive selective equalizer setting which is also a binary word that represents the cable attenuation indication within 1db. clos5_n is the most significant bit (msb) and clos0_n is the least significant bit (lsb). t able 166: liu c hannel c ontrol i nterrupt s tatus r egister (liuccisr) h ex a ddress : 0 x 0fn6 b it f unction t ype d efault d escription -o peration
xrt86vx38 185 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 168: liu c hannel c ontrol a rbitrary r egister 1 (liuccar1) h ex a ddress : 0 x 0fn8 b it f unction t ype d efault d escription -o peration 7 reserved r/w 0 6-0 arb_seg1 r/w 0 arbitrary transmit pulse shape, segment 1: these seven bits form the first of the eight segments of the transmit shape pulse when the xrt86vx38 is configured in ?arbitrary mode?. these seven bits represent the amplitude of the nth channel's arbi - trary pulse in signed magnitude format with bit 6 as the sign bit and bit 0 as the least significant bit (lsb). n ote : arbitrary mode is enabled by wr iting to the eqc[4:0] bits in register 0xnf00. t able 169: liu c hannel c ontrol a rbitrary r egister 2 (liuccar2) h ex a ddress : 0 x 0fn9 b it f unction t ype d efault d escription -o peration 7 reserved r/w 0 6-0 arb_seg2 r/w 0 arbitrary transmit pulse shape, segment 2 these seven bits form the second of the eight segments of the transmit shape pulse when the xrt86vx38 is configured in ?arbi - trary mode?. these seven bits represent the amplitude of the nth channel's arbi - trary pulse in signed magnitude format with bit 6 as the sign bit and bit 0 as the least significant bit (lsb). n ote : arbitrary mode is enabled by wr iting to the eqc[4:0] bits in register 0xnf00. t able 170: liu c hannel c ontrol a rbitrary r egister 3 (liuccar3) h ex a ddress : 0 x 0fna b it f unction t ype d efault d escription -o peration 7 reserved r/w 0 6-0 arb_seg3 r/w 0 arbitrary transmit pulse shape, segment 3 these seven bits form the third of the eight segments of the transmit shape pulse when the xrt86vx38 is configured in ?arbitrary mode?. these seven bits represent the amplitude of the nth channel's arbi - trary pulse in signed magnitude format with bit 6 as the sign bit and bit 0 as the least significant bit (lsb). n ote : arbitrary mode is enabled by wr iting to the eqc[4:0] bits in register 0xnf00.
xrt86vx38 186 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 171: liu c hannel c ontrol a rbitrary r egister 4 (liuccar4) h ex a ddress : 0 x 0fnb b it f unction t ype d efault d escription -o peration 7 reserved r/w 0 6-0 arb_seg4 r/w 0 arbitrary transmit pulse shape, segment 4 these seven bits form the forth of the eight segments of the transmit shape pulse when the xrt86vx38 is configured in ?arbitrary mode?. these seven bits represent the amplitude of the nth channel's arbi - trary pulse in signed magnitude format with bit 6 as the sign bit and bit 0 as the least significant bit (lsb). arbitrary mode is enabled by writing to the eqc[4:0] bits in register 0xnf00. t able 172: liu c hannel c ontrol a rbitrary r egister 5 (liuccar5) h ex a ddress : 0 x 0fnc b it f unction t ype d efault d escription -o peration 7 reserved r/w 0 6-0 arb_seg5 r/w 0 arbitrary transmit pulse shape, segment 5 these seven bits form the fifth of the eight segments of the transmit shape pulse when the xrt86vx38 is configured in ?arbitrary mode?. these seven bits represent the amplitude of the nth channel's arbi - trary pulse in signed magnitude format with bit 6 as the sign bit and bit 0 as the least significant bit (lsb). arbitrary mode is enabled by writing to the eqc[4:0] bits in register 0xnf00. t able 173: liu c hannel c ontrol a rbitrary r egister 6 (liuccar6) h ex a ddress : 0 x 0fnd b it f unction t ype d efault d escription -o peration 7 reserved r/w 0 6-0 arb_seg6 r/w 0 arbitrary transmit pulse shape, segment 6 these seven bits form the sixth of the eight segments of the transmit shape pulse when the xrt86vx38 is configured in ?arbitrary mode?. these seven bits represent the amplitude of the nth channel's arbi - trary pulse in signed magnitude format with bit 6 as the sign bit and bit 0 as the least significant bit (lsb). arbitrary mode is enabled by writing to the eqc[4:0] bits in register 0xnf00.
xrt86vx38 187 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 174: liu c hannel c ontrol a rbitrary r egister 7 (liuccar7) h ex a ddress : 0 x 0fne b it f unction t ype d efault d escription -o peration 7 reserved r/w 0 6 arb_seg7 r/w 0 arbitrary transmit pulse shape, segment 7 these seven bits form the seventh of the eight segments of the transmit shape pulse when the xrt86vx38 is configured in ?arbi - trary mode?. these seven bits represent the amplitude of the nth channel's arbi - trary pulse in signed magnitude format with bit 6 as the sign bit and bit 0 as the least significant bit (lsb). arbitrary mode is enabled by writing to the eqc[4:0] bits in register 0xnf00. t able 175: liu c hannel c ontrol a rbitrary r egister 8 (liuccar8) h ex a ddress : 0 x 0fnf b it f unction t ype d efault d escription -o peration 7 reserved r/w 0 6 arb_seg8 r/w 0 arbitrary transmit pulse shape, segment 8 these seven bits form the eight of the eight segments of the trans - mit shape pulse when the xrt86vx38 is configured in ?arbitrary mode?. these seven bits represent the amplitude of the nth channel's arbi - trary pulse in signed magnitude format with bit 6 as the sign bit and bit 0 as the least significant bit (lsb). arbitrary mode is enabled by writing to the eqc[4:0] bits in register 0xnf00.
xrt86vx38 188 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 176: liu g lobal c ontrol r egister 0 (liugcr0) h ex a ddress : 0 x 0fe0 b it f unction t ype d efault d escription -o peration 7 sr r/w 0 single rail mode this bit must set to "1" for single rail mode to use liu diagnotic fea - tures. the framer section must be programmed as well in register 0xn101. 0 - dual rail 1 - single rail 6 ataos r/w 0 automatic transmit all ones upon rlos: this bit enables automatic transm ission of all ones pattern upon detecting the receive loss of signal (rlos) condition. once this bit is enabled, the transmit t1 framer block will automat - ically transmit an all ?ones? data to the line for the channel that detects an rlos condition. 0 = disables the ?automatic transm it all ones? f eature upon detect - ing rlos 1 = enables the ?automatic transm it all ones? feature upon detect - ing rlos 5 rclke r/w 0 receive clock data (framer bypass mode) 0 = rpos/rneg data is updated on the rising edge of rclk 1 = rpos/rneg data is updated on the falling edge of rclk 4 tclke r/w 0 transmit clock data (framer bypass mode) 0 = tpos/tneg data is sampled on the falling edge of tclk 1 = tpos/tneg data is sampled on the rising edge of tclk 3 datap r/w 0 data polarity 0 = transmit input and receive output data is active ?high? 1 = transmit input and receive output data is active ?low? 2 reserved this bit is not used
xrt86vx38 189 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 1 gie r/w 0 global interr upt enable: this bit allows users to enable or disable the global interrupt gener - ation for all channels within the e1 liu block. once this global inter - rupt is disabled, no interrupt will be generated to the microprocessor interrupt pin even when the individual ?source? interrupt status bit pulses ?high?. if this global interrupt is enabled, users still need to enable the indi - vidual ?source? interrupt in order for the e1 liu block to generate an interrupt to the microprocessor pin. 0 - disables the global interrupt generation for all channels within the e1 liu block. 1 - enables the global interrupt generation for all channels within the e1 liu block. 0 sreset r/w 0 software reset ? p registers: this bit allows users to reset the xrt86vx38 device. writing a ?1? to this bit and keeping it at ?1? for longer than 10s initiates a device reset through the microprocessor inte rface. once the xrt86vx38 is reset, all internal circuits are placed in the reset state except the microprocessor register bits. 0 = disables software reset to the xrt86vx38 device. 1 = enables software reset to the xrt86vx38 device. t able 176: liu g lobal c ontrol r egister 0 (liugcr0) h ex a ddress : 0 x 0fe0 b it f unction t ype d efault d escription -o peration
xrt86vx38 190 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 177: liu g lobal c ontrol r egister 1 (liugcr1) h ex a ddress : 0 x 0fe1 b it f unction t ype d efault d escription -o peration 7 txsync(sect 13) r/w 0 g.703 section 13 transmit pulse when this bit is set to ?1?, the liu transmitter will send a t1 syn - chrnonous waveform as described in section 13 of itu-t g.703, except with frequency equal to 1.544mhz. this register bit takes pri - ority over every other liu se tting on the transmit path. 0 = t1 pulse specified in eqc bits 1 = section 13 synchronous pulse at 1.544mhz 6 rxsync(sect 13) r/w 0 g.703 section 13 receiver when this bit is set to ?1?, the cdr block of the receiver is configured to accept a waveform as described in section 13 of itu-t g.703 except with frequency equal to 1.544mhz. 0 = normal t1 (equalizer bit settings - equ[4:0]) 1 = section 13 synchronous pulse at 1.544mhz 5-4 gauge [1:0] r/w 00 wire gauge selector [1:0]: this bit together with guage0 bit (bit 4 within this register) are used to select the wire gauge size as shown in the table below. 3 reserved this bit is not used 2 rxmute r/w 0 receive output mute: this bit permits the user to configure the receive t1 block to auto - matically pull its recovered data output pins to gnd anytime (and for the duration that) the receive t1 liu block declares the los defect condition. in other words, if this feature is enabled, the receive t1 liu block will automatically ?mute? the recovere d data that is being routed to the receive t1 framer block anytime (and for the duration that) the receive t1 liu block declares the los defect condition. 0 ? disables the ?muti ng upon los? feature. 1 ? enables the ?muting upon los? feature. n ote : the receive clock is not mute d when this feature is enabled. gauge1 0 1 1 0 gauge0 0 1 0 1 wire size 22 and 24 gauge 26 gauge 24 gauge 22 gauge
xrt86vx38 191 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 1 exlos extended los enable: this bit allows users to extend t he number of zeros at the receive input before rlos is declared. when extended los is enabled, the receive t1 liu block will declare rlos condition when it receives 4096 number of consecu - tive zeros at the receive input. when extended los is disabled, the receive t1 liu block will declare rlos condition when it receives 175 number of consecu - tive zeros at the receive input. 0 = disables the extended los feature. 1 = enables the extended los feature. 0 ict r/w 0 in-circuit-testing enable: this bit allows users to tristate the output pins of all channels for in- circuit testing purposes. when in-circuit-testing is enabled, all output pins of the xrt86vx38 are ?tri-stated?. when in-circuit-testing is disabled, all output pins will resume to normal condition. 0 = disables the in-circuit-testing feature. 1 = enables the in-circuit-testing feature. t able 178: liu g lobal c ontrol r egister 2 (liugcr2) h ex a ddress : 0 x 0fe2 b it f unction t ype d efault d escription -o peration 7 force to "0" r/w 0 set to "0" 6-0 reserved r/w 0 these bits are not used t able 177: liu g lobal c ontrol r egister 1 (liugcr1) h ex a ddress : 0 x 0fe1 b it f unction t ype d efault d escription -o peration
xrt86vx38 192 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 179: liu g lobal c ontrol r egister 3 (liugcr3) h ex a ddress : 0 x 0fe4 b it f unction t ype d efault d escription -o peration 7-6 reserved r/w 0 these bits are not used. 5-4 mclkn[1:0] r/w 00 master t1 output clock reference [1:0] these two bits allow users to select the programmable output clock rates for the mclknout pin, according to the table below. 3-0 reserved r/w 0 these bits are not used. mclk n t1[1:0] c lock r ate of t he t1mclk n out o utput p in 00 1.544mhz 01 3.088mhz 10 6.176mhz 11 12.352mhz
xrt86vx38 193 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 t able 180: liu g lobal c ontrol r egister 4 (liugcr4) h ex a ddress : 0 x 0fe9 b it f unction t ype d efault d escription -o peration 7-4 reserved r/w 0 3-0 clksel[3:0] r/w 0001 clock select input [3:0] these four bits allow users to select the programmable input clock rates for the mclkin input pin, according to the table below. n ote : user must provide any one of the above clock frequencies to the mclkin input pin for the device to be functional. clksel[3:0] c lock r ate of t he mclkin i nput p in 0000 2.048mhz 0001 1.544mhz 0010 - 0111 reserved 1000 4.096mhz 1001 3.088mhz 1010 8.192mhz 1011 6.176mhz 1100 16.384mhz 1101 12.352mh 1110 2.048mhz 1111 1.544mhz
xrt86vx38 194 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description t able 181: liu g lobal c ontrol r egister 5 (liugcr5) h ex a ddress : 0 x 0fea b it f unction t ype d efault d escription -o peration 7-1 reserved - 0 these bits are reserved 0 gchis0 rur/ wc 0 global channel 0 interrupt status indicator this reset-upon-read bit field indicates whether or not an interrupt has occurred on channel 0 within the xrt86vx38 device since the last read of this register. 0 = indicates that no interrupt has occurred on channel 0 within the xrt86vx38 device since the last read of this register. 1 = indicates that an interrupt has occurred on channel 0 within the xrt86vx38 device since the last read of this register.
xrt86vx38 195 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 ordering information p roduct n umber p ackage o perating t emperature r ange XRT86VX38IB256 256 pin fine pitch ball grid array -40 ? c to +85 ? c xrt86vx38ib329 329 pin fine pitch ball grid array -40 ? c to +85 ? c package dimensions for 256 pin fine pitch ball grid array 256 fine pitch ball grid array (17.0 mm x 17.0 mm, fpbga) rev. 1.00 symbol min max min max a 0.058 0.070 1.48 1.78 a1 0.013 0.017 0.33 0.43 a2 0.045 0.053 1.15 1.35 d 0.661 0.677 16.80 17.20 d1 0.591 bsc 15.00 bsc b 0.020 0.024 0.50 0.60 e 0.039 bsc 1.00 bsc inches millimeters note: the control dimension is in millimeter. b a e d c a1 corner f h g j k m n p l 1 32 4 5 7 8 9 10 6 d1 12 13 14 d1 d 11 d e b a1 a a2 (a1 corner feature is mfger option) plane seating r t 15 16
xrt86vx38 196 rev. 1.0.1 8-channel t1/e1/j1 framer/liu co mbo - t1 register description package dimensions for 329 pi n fine pitch ball grid array 4 329 fine pitch ball grid array (17.0 mm x 17.0 mm, fpbga) rev. 1.00 symbol min max min max a 0.056 0.067 1.43 1.71 a1 0.010 0.014 0.26 0.36 a2 0.046 0.053 1.17 1.35 d 0.663 0.675 16.85 17.15 d1 0.567 bsc 14.40 bsc b 0.014 0.018 0.36 0.46 e 0.031 bsc 0.80 bsc inches millimeters note: the control dimension is in millimeter. b a e d c a1 corner f h g j k m n p l 1 32 4 5 7 8 9 10 6 d1 12 13 14 d1 d 11 d e b a1 a a2 (a1 corner feature is mfger option ) plane seating v w 18 17 15 16 15 15 15 19 r t u
197 notice exar corporation reserves the right to make changes to the products contained in this publicat ion in order to improve design, performanc e or reliability. exar corp oration assumes no responsibility for the use of any circuits described herein, conveys no license under any patent or other right, and makes no representation that the circuits are free of patent infr ingement. charts and schedules contai ned here in are only for illustration purposes and may vary depending upon a user?s specific application. while the information in this publication has been carefully ch ecked; no responsibility, however , is assumed for inaccuracies. exar corporation does not re commend the use of any of its products in life suppo rt applications where the failure or malfunction of the product can reasonably be ex pected to cause failure of the life support system or to significantly affect its safety or effectiveness. products ar e not authorized for use in such applications unless exar corporation receives , in writing, assuranc es to its satisfaction that: (a) th e risk of injury or damage has been minimized; (b) th e user assumes all such ris ks; (c) potential liability of exar corporation is adequately protected under the circumstances. copyright 2009 exar corporation datasheet june 2009. reproduction, in part or whole, without the prior written consent of exar co rporation is prohibited. xrt86vx38 8-channel t1/e1/j1 framer/liu co mbo - t1 register description rev. 1.0.1 p4. revision history r evision # d ate d escription 1.0.0 may 2009 release of the xrt86vx38 t1 register description datasheet. 1.0.1 june 15, 2009 update the packaging name to fpbga, upda te applications and features lists.

▲Up To Search▲

Price & Availability of XRT86VX38IB256

	To Download XRT86VX38IB256 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .