specification model ELN-60-12 eln-60-9 eln-60-15 eln-60-24 eln-60-27 eln-60-48 dc voltage rated current current range rated power output voltage adj. range note.7 current adj. range note.7 line regulation load regulation setup, rise time note.6 hold up time (typ.) voltage range note.4 frequency range efficiency (typ.) ac current (typ.) input inrush current (max.) leakage current working temp. working humidity storage temp., humidity temp. coefficient vibration mtbf dimension others note packing over current over voltage 12v 6 ~ 12v 5a 9v 15v 7.5 ~ 15v 24v 12 ~ 24v 48v 24 ~ 48v 5a 2.5a 2.3a 27v 13.5 ~ 27v 1.3a 0 ~ 5a 0 ~ 5a 0 ~ 4a 4a 0 ~ 2.5a 0 ~ 2.3a 0 ~ 1.3a 60w 45w 60w 60w 62.1w 62.5w 120mvp-p 10.8 ~ 13.2v 120mvp-p 150mvp-p 13.5 ~ 16.5v 150mvp-p 21.6 ~ 26.4v 200mvp-p 24.3 ~ 29.7v 250mvp-p 43.2 ~ 52.8v 5.0% -25% ~ 3%. can be adjusted by internal potentiometer svr2 1.0% 2.0% 500ms, 30ms / 230vac 15 at full load 00ms, 30ms / 115vac 90 ~ 264vac 127 ~ 370vdc 47 ~ 63hz 82% 85% 86% 87% 87% 88% 13.8 ~ 16v 11 ~ 13.5v 17.5 ~ 21v 28 ~ 32v 31 ~ 35v 54 ~ 60v 1.2a/115vac 0.7a/230vac cold start 60a/230vac 0.25ma / 240vac protection type : constant current limiting, recovers automatical ly after fault condition is removed -20 ~ +60 (refer to "derating curve") 20 ~ 90% rh non-condensing -40 ~ +80 , 10 ~ 95% rh 0.03%/ (0 ~ 50 ) 10 ~ 500hz, 2g 10min./1cycle, period for 60min. each along x, y, z axes 603khrs min. mil-hdbk-217f (25 ) 181*61.5*35mm (l*w*h) 1. all parameters not specially mentioned are measured at 230vac input, r ated load and 25 of ambient temperature. 2. ripple & noise are measured at 20mhz of bandwidth by using a 12" twisted pair- wire terminated with a 0.1uf & 47uf parallel capacitor. 3. tolerance : includes set up tolerance, line regulation and load regula tion. 4. derating may be needed under low input voltage. please check the static ch aracteristics for more details. 5. the power supply is considered as a component that will be operated in comb ination with final equipment. since emc performance will be affected by t he complete installation, the final equipment manufacturers must re- qualify emc directive on the complete installation again. 6. length of set up time is measured at first cold start. turning on/off the pow er supply may lead to increase of the set up time. 7. output voltage can be adjusted through the svr1 on the pcb ; limit of output co nstant current level can be adjusted through the svr2 on the pcb. 8. constant current operation region is within the specified output vol tage range above. this is the suitable operation region for led related app lications. 9. in the european market this product is only suitable for led lighting appl ications that don't have to comply with the harmonic current requiremen ts of en61000-3-2 class c. 0.4kg; 24pcs/11kg/0.75cuft 60w single output class 2 switching power supply universal ac input / full rangeprotections: short circuit / over current / over voltage cooling by free air convection built-in constant current limiting circuit with adjustable ocp level optional dimming function : 1~10vdc (d type) or pwm (p type) controlled fully isolated plastic case with ip64 level pass lps suitable for led lighting and moving sign applications (note.9) 100% full load burn-in test low cost, high reliability 2 years warranty class power unit, no fg features : e l n - 6 0 s e r i e s ripple & noise (max.) note.2 voltage tolerance note.3 environment safety & emc protection safety standards withstand voltage isolation resistance i/p-o/p:3kvac i/p-o/p:>100m ohms / 500vdc / 25 / 70% rh compliance to en55022 (cispr22) class b, en61000-3-2 class a, en610 00-3-3 compliance to en61000-4-2,3,4,5,6,8,11, en55024, light indust ry level, criteria a 8.7 ~ 10.5v ul1310 class 2, can/csa c22.2 no. 223-m91(except for 48v), ip64 approv ed ; design refer to tuv en60950-1, en61347-2-13 95 ~ 110% protection type : shut down o/p voltage, re-power on to recover 50ms/230vac 16ms/115vac at full load dimming control (optional) 1 ~ 10vdc or pwm signal : 100hz ~ 3khz function file name:eln-60-spec 2011-07-28 led operation voltage note.8 3 ~ 9v can be adjusted by internal potentiometer svr1 ip64 ( for 48v only) ( except for 48v ) lps emc immunity emc emission
mechanical specification file name:eln-60-spec 2011-07-28 case no.960a unit:mm ac/l(brown) ac/n(blue) 300 2 0 300 20 6.26 6.26 181 21.25 61.5 21.25 35 +v(red) -v(black) 2-r2.5 +v(red) dim+(blue) -v(black) dim-(white) output(with optional dimming function) dim- dim+ optional dimming control 10v pwm or 1~10v load (%) -15 -5 0 15 30 20 40 50 60 80 100 input voltage (v) 60hz 90 100 125 135 145 155 165 175 180 200 230 264 100 90 80 70 60 50 40 load (%) derating curve load (%) 0 40 45 50 derating curve static characteristics ambient temperature ( ) load (%) -20 60 175 load (%) svt 18awg 2c svt 18awg 2c 116.5 t case 15 ul2464 18awg 4c t case: max. case temperature. e l n - 6 0 s e r i e s fosc : 60khz block diagram detection pwm circuit o.l.p. emi filter rectifiers power switching filter & rectifiers +v -v i/p control o.v.p. & o.c.p. (horizontal) 60w single output class 2 switching power supply output voltage and current adjustment : remove the upper case and adjust th rough svr1 & svr2 shown in the diagram. output voltage adjustment output current adjustment svr1 svr2 svr2 svr1
(1)1~10v (d type, & : eln-60- 12 12 d) p) level of output current can be adjusted through the dimming control funct ion. when there is no signal sending to the control wires (open circuit between th e two control wires), the power supply unit will operate as 0v (d-type) or 0% duty (p-type) of input signal and hence t he output current will be zero. lo:0v hi:10v 0 0% 1 11% 15% 60% 95% 2 20% 3 30% 4 40% 5 50% 6 60% 7 70% 8 80% 9 90% 10 100% dimming control (optional) vdc: 1~10v vdc (2)pwm (p type, & : eln-60- + dim+ f t1 t1 t1+t2 f: 100hz ~ 3khz duty= ,0 ~ 100% t2 v 10v f dim- dc input duty cycle output current output current 10% 10% 0% 0% 20% 20% 30% 30% 40% 40% 50% 50% 60% 60% 70% 70% 80% 80% 90% 90% 100% 100% 95% 5% 45% e l n - 6 0 s e r i e s file name:eln-60-spec 2011-07-28 60w single output class 2 switching power supply
|
