e e - - p p h h e e m m t t a a e e 3 3 0 0 8 8 ? tel : 82-31-250-5011 ? all specifications may change without notice. ? rfsales@rfhic.com ? version 1.3 product features application ? 50mhz ~ 1ghz ? gaas e-phemt ? 22db gain ? 2.0 db noise figure ? +18.0 dbm p1db ? sot-89 smt package ? single +5v supply ? pb free / rohs standard ? catv amplifier description AE308 is used from 50mhz to 1ghz frequencies a nd gaas e-phemt in a low cost sot-89 package. the package is sot-89, which is pin-to-p in compatible with industry standard. specifications u nits m in typ m ax c on dition mhz 50mhz 1ghz v5 vdc=5v ma 40 55 70 db 22 50mhz~1ghz db -15 db -15 db m 27 29 db m 17 19 50mhz~500mhz dbm 15 17 500mhz~1ghz dbc374554 50mhz~1ghz db 1.5 50mhz~800mhz db 2 800mhz~1ghz c so db c -58 135 channels,+16dbmv/ch,single ctb db c -64 135 channels,+16dbmv/ch,single xmd db c -67 135 channels,+16dbmv/ch,single s21-gain oip2 noise figure parameter frequency r ange supply voltage current p1db 50 - 870mhz s11-input return loss s22-o u tpu t re tur n lo ss oip3 note 1. test conditions unless otherwise noted. t=25 , vd c=5.0v, 75 ? system 2. oip3 measured with 2 tones at an out put power of 5dbm/tone separated by 1mhz mhz 50mhz 1ghz db 22 22 db -15 -15 db -15 -15 dbm 29 28 dbm 19 17 dbc 45 54 db 1.3 2 dbc dbc dbc v ma supply voltage cso ctb xmd s21-gain -58 -64 -67 5 40~70 frequency current s11-input return loss noise figure s22-output return loss oip3 p1db oip2 typical performance (1) 135channels, 16dbmv/ch, single * v dc = 5v; t case = 25 ; z s = z l = 75 ? absolute maximum ratings parameter minimum rating maximum rating operating case temperature ( ) -40 85 storage temperature ( ) -50 125 drain-source voltage (v) +7 package type: sot-89 www.datasheet.co.kr datasheet pdf - http://www..net/
e e - - p p h h e e m m t t a a e e 3 3 0 0 8 8 ? tel : 82-31-250-5011 ? all specifications may change without notice. ? rfsales@rfhic.com ? version 1.3 typical rf performance at 25 application (50mhz~1ghz) units mhz 50 450 1000 db 22 22 22 db -15 -15 -15 db -15 -15 -15 dbm 29 30 28 dbm 19 19 17 dbc 45 42 54 db 1.3 1.5 2 dbc dbc dbc v ma 5 40~70 typical supply voltage cso ctb xmd -58 -64 -67 s21-gain parameter frequency current s11-input return loss noise figure s22-output return loss oip3 p1db oip2 (1) 135channels,+16dbmv/ch,single single ? ended catv 75 ? evaluation circuit : (50mhz ~1ghz) r8 150 ohm c4 1.8pf rf in c9 4.7uf/16v c8 10nf r2 160 ohm c6 1.8pf r4 10 ohm c5 1.8pf l1 560nh AE308 l6 6.8nh r6 1.5k ohm +5v l2 560nh c2 10nf l4 27nh r f r1 18 ohm l5 12nh c7 10nf r5 18 ohm l3 10nh r3 1k ohm r7 1.5k ohm c1 10nf c3 10nf www.datasheet.co.kr datasheet pdf - http://www..net/
e e - - p p h h e e m m t t a a e e 3 3 0 0 8 8 ? tel : 82-31-250-5011 ? all specifications may change without notice. ? rfsales@rfhic.com ? version 1.3 dimensions pcb pad layout recommended mounting configuration mountin g confi g uration notes 1.ground / thermal via holes are critical for the proper performance of this device. 2. add as much copper as possible to inner and outer layers near the part to ensure optimal thermal performance. 3. mounting screws can be added near the part to fasten the board to a heatsink. ensure that the ground / thermal via hole regi on contacts the heatsink. 4. do not put solder mask on the backside of the p cb in the region where the board contacts the heatsink. 5. rf trace width depends upon th e pcb material and construction. 6. use 1 oz. copper minimum. 7. all dimensions are in millimeters. rfhic corporation (rfhic) reserves the right to make changes to any products herein or to discontinue any product at any time w ithout notice. rfhic do not assume any liability for the suitability of its products for any particular purpose, and disclaims any and all liability, inclu ding without limitation consequential or incidental damages. the product specifications herein expressed have been carefully checked and are assumed to be reliable. how ever, rfhic disclaims liability for inaccuracies and strongly recommends buyers to verify that the information they are using is current before placing purchase or ders. rfhic products are not intended for use in life support equipment or application where ma lfunction of the product can be expected to result in persona l injury or death. buyer uses or sells such products for any such unintended or unauthorized applicatio n, buyer shall indemnify, protect and hold rfhic and its direct ors, officers, stockholders, employees, representatives and distributors harmless against any a nd all claims arising out of such use. rfhic?s liability unde r or arising out of damages, claims of whatsoever kind and nature which rfhic p roducts could cause shall be limited in amount to the net p urchase p rice of the p roducts sold to bu y er b y rfhic . pin no function 1 input 2 ground 3 output 4 ground ! esd sensitive observe precautions for handlin g, testing and packaging. www.datasheet.co.kr datasheet pdf - http://www..net/
|
