surface mount aluminum electrolytic capacitors lower impedance, 105 c cat. no. e1001d @ very low impedance, 105 c 2000 hour-life @ pb-free design : sn-bi plating terminal @ solvent-proof type (see precautions and guidelines) ? specifications (20 c , 120hz) (at 20 c after 2 minutes) (20 c , 120hz) (120hz) category temperature range rated voltage range capacitance tolerance leakage current dissipation factor (tan e ) low temperature characteristics (max. impedance ratio) endurance items -55 to +105 c 6.3 to 50v dc p 20%(m) i=0.01cv or 3 m a, whichever is greater where, i : max. leakage current ( m a), c : nominal capacitance ( m f), v : rated voltage (v) rated voltage(v dc ) tan e (max.) rated voltage(v dc ) z(-25 c )/z(+20 c ) z(-40 c )/z(+20 c ) z(-55 c )/z(+20 c ) the following specifications shall be satisfied when the capacitors are restored to 20 c after the rated voltage is applied for 2000 hours at 105 c . capacitance change [p 30% of the initial measured value d.f. (tan e ) [ 200% of the initial specified value leakage current [ the initial specified value characteristics 6.3v 0.26 6.3v 2 3 4 10v 0.19 10v 2 3 4 16v 0.16 16v 2 3 4 25v 0.14 25v 2 3 3 35v 0.12 35v 2 3 3 50v 0.10 50v 2 3 3 ? part numbering system ? dimensions [mm] ? standard ratings rated ripple current (marms) at 105 c , 100khz impedance ( o max.) at 20 c , 100khz case code 6.3 10 16 25 35 50 4.7 10 22 33 47 100 220 330 470 680 1000 1500 d61 d61 e61 e61 f61 f61 f80 h10 h10 j10 1.35 1.35 0.70 0.70 0.36 0.36 0.34 0.16 0.16 0.08 90 90 160 160 240 240 280 600 600 850 d61 d61 e61 f80 h10 h10 h10 j10 1.35 1.35 0.70 0.34 0.16 0.16 0.16 0.08 90 90 160 280 600 600 600 850 d61 d61 e61 e61 f61 f61 f80 h10 h10 j10 1.35 1.35 0.70 0.70 0.36 0.36 0.34 0.16 0.16 0.08 90 90 160 160 240 240 280 600 600 850 d61 e61 e61 f61 f61 f80 h10 h10 j10 1.35 0.70 0.70 0.36 0.36 0.34 0.16 0.16 0.08 90 160 160 240 240 280 600 600 850 d61 d61 e61 e61 f61 f61 f80 h10 h10 j10 1.35 1.35 0.70 0.70 0.36 0.36 0.34 0.16 0.16 0.08 90 90 160 160 240 240 280 600 600 850 d61 e61 f61 f61 f80 f80 h10 j10 2.90 1.52 0.88 0.88 0.68 0.68 0.34 0.18 60 85 165 165 195 195 350 670 v dc m f ? marking f d p 0.5 l p 0.3 (note) 0.3max. a p 0.2 w c p 0.2 b p 0.2 p note : l p 0.5 for h10 and j10 case code d61 e61 f61 f80 h10 j10 d 4 5 6.3 6.3 8 10 l 5.8 5.8 5.8 7.7 10.0 10.0 a 4.3 5.3 6.6 6.6 8.3 10.3 b 4.3 5.3 6.6 6.6 8.3 10.3 c 5.1 5.9 7.2 7.2 9.0 11.0 w 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.7 to 1.1 0.7 to 1.1 p 1.0 1.4 1.9 1.9 3.1 4.5 2j 220 c za ex) 16v220 m f mza 16 vc 220 m f80 capacitance 4.7 m f 10 m f 100 m f 1000 m f code 4r7 10 100 1000 case code capacitance tolerance ( p 20%) nominal capacitance code terminal type (vc) rated voltage in volts series name ? rated voltage code rated voltage (v dc ) 6.3 10 16 25 35 50 code j a c e v h new! lower z mza mvz lower z mvy note : use next higher voltage part. (1/1)
|