ayf33 ordering information fpc connectors for fpc connection fpc connectors y3b (0.3 mm pitch) (former name: yf33) features 1. the world s slimmest* and low pro?e design (pitch: 0.3 mm) the industry s smallest space* among back lock type fpc connectors has been achieved with a depth of 3.15 mm (including the lever). the 0.9 mm low-pro?e facilitates the thickness and size reduction of target equipment. * among back lock type fpc connectors based on our research as of october 2009 2. mechanical design freedom achieved by top and bottom double contacts the top and bottom double contacts eliminate the need of using different connectors (with either top or bottom contacts) depending on the fpc wiring conditions. 3. easy-to-handle back lock structure 4. man-hours for assembly can be reduced by delivering the connectors with their levers opened. 5. wiring patterns can be located underneath the connector. 6. ni barrier with high resistance to solder creep applications compact mobile devices ?ellular phones, digital cameras and dvc, etc compliance with rohs directive unit: mm 0.9 3.15 33: fpc connector 0.3 mm pitch (back lock) ayf 3 3 53 number of contacts (2 digits) contact direction 3: top and bottom double contacts surface treatment (contact portion / terminal portion) 5: au plating/au flash plating (ni barrier) panasonic-electric-works.net/ac
ayf33 product types notes: 1. order unit; for mass production: in 1-inner carton (1-reel) units samples for mounting check: in 50-connector units. please contact our sales of?e. 2. please contact our sales of?e for connectors having a number of contacts other than those listed above. specifications 1. characteristics 2. material and surface treatment height number of contacts pa rt number pac king inner carton outer carton 0.9 mm 7a yf330735 5,000 pieces 10,000 pieces 9 ayf330935 13 ayf331335 15 ayf331535 21 ayf332135 23 ayf332335 25 AYF332535 27 ayf332735 31 ayf333135 33 ayf333335 35 ayf333535 39 ayf333935 45 ayf334535 51 ayf335135 item speci?ations conditions electrical characteristics rated current 0.2a/contact rated voltage 50v ac/dc insulation resistance min. 1,000m ? (initial) using 250v dc megger (applied for 1 min.) breakdown voltage 150v ac for 1 min. no short-circuiting or damage at a detection current of 1 ma when the speci?d voltage is applied for one minute. contact resistance max. 100m ? based on the contact resistance measurement method speci?d by jis c 5402. mechanical characteristics fpc holding force min. 0.13n/contacts contacts (initial) measurement of the maximum force applied until the inserted compatible fpc is pulled out in the insertion axis direction while the connector lever is closed contact holding force min. 0.2n/contacts measuring the maximum force. as the contact is axially pull out. environmental characteristics ambient temperature ?5 c to +85 c no freezing at low temperatures. no dew condensation. storage temperature ?5 c to +85 c (product only) ?0 c to +50 c (emboss packing) thermal shock resistance (with fpc inserted) 5 cycles, insulation resistance min. 100m ? , contact resistance max. 80m ? sequence 1. ?5 c, 30 minutes 2. ~ , max. 5 minutes 3. 85 c, 30 minutes 4. ~ , max. 5 minutes humidity resistance (with fpc inserted) 120 hours, insulation resistance min. 100m ? , contact resistance max. 100m ? bath temperature 40 2 c, humidity 90 to 95% r.h. saltwater spray resistance (with fpc inserted) 24 hours, insulation resistance min. 100m ? , contact resistance max. 100m ? bath temperature 35 2 c, saltwater concentration 5 1% h 2 s resistance (with fpc inserted) 48 hours, contact resistance max. 100m ? bath temperature 40 2 c, gas concentration 3 1 ppm, humidity 75 to 80% r.h. soldering heat resistance peak temperature: 260 c or less re?w soldering 300 c within 5 sec. 350 c within 3 sec. soldering iron lifetime characteristics insertion and removal life 20 times repeated insertion and removal: min. 10 sec./time unit weight 51-contact type: 0.08 g pa rt name material surface treatment molded portion housing: lcp resin (ul94v-0) lever: lcp resin (ul94v-0) contact copper alloy contact portion; base: ni plating, surface: au plating te r minal portion; base: ni plating, surface: au plating 0 ? 3 + 3 0 panasonic-electric-works.net/ac
ayf33 dimensions (unit: mm) recommended fpc dimensions embossed tape dimensions (unit: mm) (common for respective contact type) ?dimension table (unit: mm) number of contacts type of taping a b c quantity per reel 7 to 15 contacts tape i 16.0 7.5 17.4 5,000 21 to 45 contacts tape i 24.0 11.5 25.4 5,000 51 contacts tape ii 32.0 14.2 33.4 5,000 (1.84) 0.90 0.10 2.95 (3.15) (1.35) (fpc insertion depth) (0.10) (0.10) (0.40)(0.30) c 0.20 b 0.20 a 1.35 (suction area) 0.60 0.10 (terminal pitch) 0.30 0.10 (terminal pitch) 0.60 0.10 (terminal pitch) 0.1 (contact) te r minal coplanarity number of contacts/ dimension a b c 7 3.60 1.80 1.20 9 4.20 2.40 1.80 13 5.40 3.60 3.00 15 6.00 4.20 3.60 21 7.80 6.00 5.40 23 8.40 6.60 6.00 25 9.00 7.20 6.60 27 9.60 7.80 7.20 31 10.80 9.00 8.40 33 11.40 9.60 9.00 35 12.00 10.20 9.60 39 13.20 11.40 10.80 45 15.00 13.20 12.60 51 16.80 15.00 14.40 3.00 0.50 (reinforcing plate) 0.20 0.03 0.15 max. 0.10 max. 0.10 max. 0.20 0.02 2.00 0.30 (exposed part of the conductor) 1.55 0.15 1.45 0.15 1.35 0.15 0.75 0.10 0.65 0.10 2-r0.20 a 0.05 0.60 0.02 (pitch) 0.60 0.07 0.30 0.02 (pitch) 0.60 0.02 (pitch) c 0.03 b 0.03 0.30 0.07 (contact width) +0.04 ?.03 0.30 (contact width) +0.04 ?.03 0.30 (finished thickness: t = 0.2 0.03) the conductive parts should be based by ni plating and then au plating. number of contacts/ dimension a b c 7 2.40 1.80 1.20 9 3.00 2.40 1.80 13 4.20 3.60 3.00 15 4.80 4.20 3.60 21 6.60 6.00 5.40 23 7.20 6.60 6.00 25 7.80 7.20 6.60 27 8.40 7.80 7.20 31 9.60 9.00 8.40 33 10.20 9.60 9.00 35 10.80 10.20 9.60 39 12.00 11.40 10.80 45 13.80 13.20 12.60 51 15.60 15.00 14.40 ?speci?ations for taping (in accordance with jis c 0806-1990. however, not applied to the mounting-hole pitch of some connectors.) ?speci?ations for the plastic reel (in accordance with eiaj et-7200b.) 28.40 (b) (b) (1.75) (1.75) (4.0) (2.0) (8.0) (4.0) (2.0) (8.0) (a 0.3) tape i tape ii (a 0.3) a: max. 24mm a: 32mm leading direction after packaging 1.50 dia. +0.1 0.0 1.50 dia. +0.1 0.0 embossed mounting-hole taping reel top cover tape embossed carrier tape 380 dia. (c 1) label panasonic-electric-works.net/ac
ayf33 ?connector orientation with respect to embossed tape feeding direction notes type direction of tape progress y3b 1. recommended pc board and metal mask patterns appropriate control of solder amount is required to minimize solder bridges and other defects for connectors with 0.3 mm, 0.4 mm or 0.5 mm pitch terminals, which require high-density mounting. refer to the recommended pc board pattern. 2. precautions for insertion/removal of fpc do not apply an excessive load to the lever in the opening direction beyond its open position; otherwise, the lever may be deformed or removed. do not open/close the lever without an fpc inserted; otherwise, the terminals may be deformed, and the fpc insertion force may increase. do not apply an excessive load to the lever in a direction perpendicular to the lever rotation axis or in the lever opening direction; otherwise, the terminals may be deformed, and the lever may be removed. these connectors are of the back lock type, which has the fpc insertion section on the opposite side of the lever. be careful not to make a mistake in the fpc insertion position or the lever opening/ closing position. otherwise, a contact failure or connector breakage may occur. these connectors have top and bottom double contacts. do not insert an fpc upside down. inserting an fpc in a direction opposite to that you intended may cause an operation failure or malfunction. fully open the lever to insert an fpc. completely insert the fpc horizontally. an fpc inserted at an excessive angle to the board may cause the deformation of metal parts, fpc insertion failures, and fpc circuit breakages. insert the fpc to the full depth of the connector without altering the angle. to close the lever, turn down the lever by pressing the entire lever or both sides of the lever with the balls of ?gers. be careful. if pressure to the lever is applied unevenly, such as to an edge only, it may deform or break. also, make sure that the lever is closed completely. not doing so will cause a faulty connection. av oid applying an excessive load to the top of the lever during or after closing the lever. otherwise, the terminals may be deformed. when opening the lever to remove the fpc, ensure that the lever will not go over the initial position; otherwise, the lever may be removed. remove the fpc at parallel with the lever fully opened. if the lever is closed, or if the fpc is forcedly pulled, the product or fpc may break. if a lever is accidentally detached during the handling of a connector, do not use the connector any longer. after an fpc is inserted, carefully handle it so as not to apply excessive stress to the base of the fpc. number of contacts/ dimension b c 7 1.80 1.20 9 2.40 1.80 13 3.60 3.00 15 4.20 3.60 21 6.00 5.40 23 6.60 6.00 25 7.20 6.60 27 7.80 7.20 31 9.00 8.40 33 9.60 9.00 35 10.20 9.60 39 11.40 10.80 45 13.20 12.60 51 15.00 14.40 te rm inal connector outline (lever opened) 3.20 0.03 0.70 0.03 0.50 0.03 b 0.05 0.60 0.03 0.30 0.03 c 0.05 0.60 0.03 0.30 0.03 recommended pc board pattern (mount pad arrangement pattern) for other cautions, please refer to the last page. panasonic-electric-works.net/ac
fpc connectors common cautions for use common cautions for use pc board design design the recommended foot pattern in order to secure the mechanical strength in the soldered areas of the terminal. fpc and equipment design design the fpc based on the recommended dimensions to ensure the required connector performance. in addition, carefully check the equipment design and take required measures for the equipment to prevent the fpc from being removed subsequent to a fall, vibration, or other impact due to the fpc size, weight, or the reaction force of the routed fpc. connector mounting in case the connector is picked up by chucking during mounting, an excessive mounter chucking force may deform the molded or metal part of the connector. consult us in advance if chucking is to be applied. soldering 1) manual soldering. ?due to the low pro?e, if an excessive amount of solder is applied to this product during manual soldering, the solder may creep up to near the contact points, or interference by solder may cause imperfect contact. ?make sure that the soldering iron tip is heated within the temperature and time limits indicated in the speci?ations. ?flux from the solder wire may adhere to the contact surfaces during soldering operations. after soldering, carefully check the contact surfaces and clean off any ?x before use. ?be aware that a load applied to the connector terminals while soldering may displace the contact. ?thoroughly clean the iron tip. 2) re?w soldering ?screen-printing is recommended for printing paste solder. y3ft/y3f/y3b y5s ?screen thickness of 120 m is recommended for paste solder printing. ?consult us when using a screen-printing thickness other than that recommended. ?depending on the size of the connector being used, self alignment may not be possible. accordingly, carefully position the terminal with the pc board pattern. ?the recommended re?w temperature pro?e is given in the ?ure below recommended re?w temperature pro?e y3ft/y3f/y3b y5s y5f ?the temperature is measured on the surface of the pc board near the connector terminal. ?some solder and ?x types may cause serious solder creeping. take the solder and ?x characteristics into consideration when setting the re?w soldering conditions. ?when performing re?w soldering on the back of the pc board after re?w soldering the connector, secure the connector using, for example, an adhesive. (double re?w soldering on the same side is possible) 3) reworking on a soldered portion ?finish reworking in one operation. ?for reworking of the solder bridge, use a soldering iron with a ?t tip. do not add ?x, otherwise, the ?x may creep to the contact parts. ?use a soldering iron whose tip temperature is within the temperature range speci?d in the speci?ations. do not drop the product or handle carelessly. otherwise, the terminals may become deformed due to excessive force or the solderability during re?w soldering may degrade. don? open/close the lever or insert/ remove an fpc until the connector is soldered. forcibly applied external pressure on the terminals can weaken the adherence of the terminals to the molded part or cause the terminals to lose their evenness. in addition, do not insert an fpc into the connector before soldering the connector. when cutting or bending the pc board after mounting the connector, be careful that the soldered sections are subjected to excessive forces. other notes when coating the pc board after soldering the connector to prevent the deterioration of insulation, perform the coating in such a way so that the coating does not get on the connector. the connectors are not meant to be used for switching. to determine the relationship between the screen opening area and the pc board foot pattern area, refer to the diagrams in the recommended patterns for pc boards and metal masks when setting. note that excess solder on the terminals prevents complete insertion of the fpc, and that excess solder on the metal clips prevents the lever from rotating. note that excess solder inhibits the slider lock operation. te rm inal paste solder pc board foot pattern 150 c 180 c 230 c 220 c 200 c 260 c temperature upper limit (soldering heat resistance) lower limit (solder wettability) preheating peak temperature time 25 sec. 70 sec.60 to 120 sec. 250 c 200 c 180 c 150 c time peak temperature preheating 60 to 120 sec. min. 200 c, 70 sec. te mperature 260 c 200 c 180 c 150 c time peak temperature preheating 60 to 120 sec. min. 200 c, 70 sec. te mperature do not the soldered areas to be subjected to forces panasonic-electric-works.net/ac for other details, please verify with the product speci?ation sheets.
|
