input characteristics 90-132/180-264vac u = autoranging output power/current v out 5v v out < 5v s = 300w s = 60a p = 450w p = 90a m = 600w m = 120a product grade e = 0? to +85? case c = 0? to +85? case i = -30? to +85? case output power/current v out 5v v out < 5v y = 50w y = 10a x = 75w x = 15a w = 100w w = 20a v = 150w v = 30a u = 200w u = 40a product highlights if you?e looking for the convenience of a complete, low profile, agency- approved switching power supply, look no further. the flatpac combines vicor s workhorse vi-200 family of dc-dc converters with a modular package and front end subassembly to provide from 50 to 600w of output power from one to three outputs. a flat plate heatsink for use in conduction cooled applications may be specified as an alternate to the standard finned version by adding ?c?to the end of the model number. vicor s flatpac is also available with a current controlled output using batmod converter modules of 12, 24, or 48vdc outputs. this option is specified by appending ?m?or ?c (for conduction cooled versions) to the end of the flatpac model number. the flatpac s contemporary design allows us to configure your order quickly and provide rapid turnaround on standard models. it is truly a complete power solution, enabling you to spend more time designing your system and less time worrying about how to power it. features ? microcontroller architecture ? inputs: 115/230vac autoranging ? meets fcc part 15, en55022, class b conducted emissions ? 80-90% efficiency ? any output: 1 to 95vdc ? module enable/disable (except lu series) ? ul, csa, t?v, vde, babt, ce marked ? remote sense and current limit ? bus ok and ac ok (except lu series) ? 40ms ride-through time ? ovp and thermal shutdown ? 1 output; up to 200w ? 1 or 2 outputs; up to 400w ? 1, 2, or 3 outputs; up to 600w flatpac 50 to 600w autoranging ac-dc switchers flatpac configuration chart typical model: v i - r u input: 115/230vac ; output 1: 5vdc at 200w output 2: 12vdc at 200w output 3: 12vdc at 200w # of total power part no. converters dimensions 50-200w vi-lu 1 9.25" x 2.5" x 1.37" (234,8 x 63,5 x 34,8mm) 200-400w vi-mu 2 9.25" x 4.9" x 1.37" (234,8 x 124,5 x 34,8mm) 300-600w vi-nu 3 9.25" x 7.3" x 1.37" (234,8 x 185,4 x 34,8mm) 100-400w vi-pu ? 2 9.25" x 4.9" x 1.37" (234,8 x 124,5 x 34,8mm) 150-600w vi-qu ? 3 9.25" x 7.3" x 1.37" (234,8 x 185,4 x 34,8mm) 150-600w vi-ru ? 3 9.25" x 7.3" x 1.37" (234,8 x 185,4 x 34,8mm) u u u e 1 1 0 single outputs: dual outputs: triple outputs: options bc = batmod/conduction cooled bm= batmod cc = conduction cooled output voltage z 2v m 10v k 40v y 3.3v 1 12v 4 48v 0 5v p 13.8v h 52v x 5.2v 2 15v f 72v w 5.5v n 18.5v d 85v v 5.8v 3 24v b 95v t 6.5v l 28v r 7.5v j 36v output power v out 5v v out < 5v w = 100w w = 20a v = 150w v = 30a u = 200w u = 40a s = 300w s = 60a q = 400w q = 80a flatpac 10/02 1 of 4
flatpac specifications (typical at 25?, nominal line and 75% load, unless otherwise specified.) input characteristics ac line input autoranging 90-132/180-264vac line frequency 47 to 63hz (c-grade and e-grade) 47 to 440hz (i-grade) inrush current 115vac operation 1 converter: 16a @ peak line; 2 converters: 23a @ peak line; 3 converters: 39a @ peak line 230vac operation 1 converter: 32a @ peak line; 2 converters: 47a @ peak line; 3 converters: 78a @ peak line ride-through time (full load) 90/180vac low line 5ms minimum 115/230vac nominal line 40ms minimum ac fail warning time 5ms minimum (low line, full load) ac and bus ok (2 converter and 3 converter models only) off state vce = 70v maximum on state vcesat = 0.4v maximum @ 1ma (1.5ma max.) module disable (2 converter and 3 converter models only, optically isolated led input) continuous forward current 1 ma to 30ma forward voltage 1.65v max. at 30ma dielectric withstand primary to chassis gnd 2,121vdc primary to secondary 4,242vdc secondary to chassis gnd 707vdc output characteristics (applies to each output individually) e-grade c-, i-grade min. typ. max. min. typ. max units notes setpoint accuracy 1% 2% 0.5% 1% v nom load/line regulation 0.5% 0.05% 0.2% v nom ll to hl, 10% to full load load/line regulation 1% 0.2% 0.5% v nom ll to hl, no load to full load output temperature drift 0.02 0.01 0.02 %/? over rated temperature long term drift 0.02 0.02 %/1k hours output ripple 2v 150mv 60mv 100mv p-p 20mhz bandwidth 5v 5% 2% 3% p-p 20mhz bandwidth 10-48v 3% 0.75% 1.5% p-p 20mhz bandwidth output voltage trimming 1 50% 110% 50% 110% total remote sense compensation 0.5 0.5 volts 0.25v max. neg. leg ovp setpoint 125% 115% 125% 135% v nom recycle power current limit 105% 135% 105% 125% i nom automatic restart short circuit current 2 20% 140% 20% 130% i nom thermal characteristics efficiency 78-88% 80-90% shutdown temp. ?case 90 95 105 90 95 105 ? cool and recycle power to restart operating temp. ?case 85 85 ? see thermal curves mechanical specifications weight 3 22.4 (652) 22.4 (652) ounces (grams) safety agency approvals ul, csa, t?v, vde, iec 950, ce marked for low voltage directive, 73/23/eec environmental characteristics/product grade designators storage temperature -20? to +100? (c-grade and e-grade) -55? to +100? (i-grade) operating temperature (case) 0? to +85? (c-grade and e-grade) -30? to +85? (i-grade) emi / emc characteristics (performed on selected samples representative of the u series flatpac product family.) conducted emissions, lisn en 55022 and fcc r&r, part 15, subpart b, class b electrostatic discharge iec 801-2, 1991, level 4; ?kv contact, 15kv air discharge rf radiated immunity, e-field iec 801-3, 1984; 27mhz to 500mhz, 3 v/m, cw electrical fast transients/burst en 61000-4-4, level 2; ?kv, surge immunity en 61000-4-5, class 3; ?kv line to ground, ?kv line to line 1 10, 12v and 15v outputs, trim range ?0%. consult factory for wider trim range. 2 output voltages of 5v or less incorporate foldback current limiting, greater than 5v incorporate straight line current limiting . 3 for mu, pu series, multiply value by 2; for nu, qu, ru series, multiply value by 3. flatpac 10/02 2 of 4
thermal curves, 5v output thermal curves, 10 to 48v output 0 75 150 225 300 375 450 525 600 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 ambient temperature (deg. c) output power (watts) 0 25 50 75 100 125 150 175 200 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 ambient temperature (deg. c) output power (watts) 0 50 100 150 200 250 300 350 400 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 ambient temperature (deg. c) output power (watts) 0 75 150 225 300 375 450 525 600 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 ambient temperature (deg. c) output power (watts) 0 25 50 75 100 125 150 175 200 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 ambient temperature (deg. c) output power (watts) 0 50 100 150 200 250 300 350 400 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 ambient temperature (deg. c) output power (watts) application circuits mod dis e mod dis + ac ok e ac ok + bus ok e bus ok + internal supervisory circuits (optocouplers) ac mains earth ground l1 l2/n gnd 2-up and 3-up 1-up v line 90 (180) vac ac line interrupted ac line ac ok bus ok t0 t1 t2 t3 t4 conditions: full load 90 (180) vac, ac line time interval min typ max units notes t0-t1 0 0.1 1.0 ms t2-t3 0 40 ms ride-through time t2-t4 5 ms hold-up time t3-t4 5 ms ac fail warning time resistor values for trimming standard output voltages nom. output voltage 5v 12v 15v 24v 28v 48v trim range r1(k ? ) 0.953 15.8 22.1 41.2 48.7 90.9 +10%, -10% r2(k ? ) 909090909090 r2 +s trim 10k r1 + vout vout rtn +o o s ac mains connections power up and power down sequencing output trimming ambient temperature (deg. c) ambient temperature (deg. c) ambient temperature (deg. c) ambient temperature (deg. c) ambient temperature (deg. c) ambient temperature (deg. c) lu series mu, pu series nu, qu, ru series lu series mu, pu series nu, qu, ru series output power (watts) output power (watts) output power (watts) output power (watts) output power (watts) output power (watts) free air 50 lfm 100 lfm 250 lfm 500 lfm 750 lfm 1000 lfm free air 50 lfm 100 lfm 250 lfm 500 lfm 750 lfm 1000 lfm flatpac 10/02 3 of 4
mechanical drawings 10 11 12 13 14 15 16 7 8 9 mounting hole 0.15 0.01 thru 4 places 2.156 0.010 54.76 0.25 0.192 0.010 4.88 0.25 0.18 4.57 6.00 152.4 2.540 0.030 64.52 0.76 1.27 32.26 output 1 mounting hole 0.15 0.01 thru 5 places 10 16 10 11 12 13 14 15 16 10 11 12 13 14 15 16 10 11 12 13 14 15 16 7 8 9 1 2 3 4 5 6 4.562 0.010 115.87 0.25 2.281 0.010 57.94 0.25 0.199 0.010 5.05 0.25 0.18 4.57 6.00 152.4 4.960 0.030 125.98 0.76 3.83 97.16 1.17 29.72 output 1 output 2 output 1 + 10 11 12 13 14 15 16 10 16 10 11 12 13 14 15 16 10 11 12 13 14 15 16 10 11 12 13 14 15 16 10 11 12 13 14 15 16 10 16 10 16 10 11 12 13 14 15 16 7 8 9 1 2 3 4 5 6 7.000 0.010 177.8 0.25 4.710 0.010 119.63 0.25 2.290 0.010 58.17 0.25 mounting hole 0.15 0.01 thru 6 places 0.190 0.010 4.83 0.25 0.18 4.57 6.00 152.4 7.380 0.030 187.45 0.76 5.48 139.19 1.93 49.02 output 1 output 2 output 3 output 1 output 1 output 2 + + + 12 1.375 0.020 34.91 0.51 0.50 12.57 9.245 0.030 234.82 0.76 1.11 28.19 measure case temperature this surface. inputs 1 mod dis 2 mod dis+ 3 ac ok 4 ac ok+ 5 bus ok 6 bus ok+ 7 ac in l1 8 ac in l2/n 9 chassis gnd outputs 10 +out (#10-32 stud) 11 +out 12 +sense (v trim *) 13 trim (i trim *) 14 sense (i mon *) 15 out 16 out (#10-32 stud) *on flatpacs with batmods only. input connector, amp p/n 644488-6; mating connector, mta-100 idc series terminals for #16-12 awg wire output connector, amp p/n 644486-5; mating connector, mta-100 idc series all models lu series mu, pu series nu, qu, ru series flatpac 10/02 4 of 4
|
