1 / 7 asb inc. sales@asb .co.kr tel: +82 - 42 - 528 - 7223 may 2012 as l09s 5 - 40 00 mhz high linearity lna mmic parameters units typical frequency mhz 800 1950 2400 2700 3500 gain db 19.3 12.8 11 10 7.5 s11 db - 18 - 18 - 20 - 20 - 18 s22 db - 10 - 10 - 9.5 - 9.5 - 9 output ip3 1) dbm 32 34.5 35.5 36.5 36 noise figure db 0.8 0.9 1.1 1.2 1.5 output p1db dbm 19.5 19.5 20 19.5 20 current ma 45 45 45 45 45 device voltage v 4.4 4.4 4.4 4.4 4.4 1) oip3 is measured with two tones at an output power of +5 dbm/tone separated by 1 mhz. parameters units min typ max testing frequency mhz 1950 gain db 12.8 s11 db - 18 s22 db - 10 output ip3 dbm 34.5 noise figure db 0.9 output p1db dbm 19.5 current ma 45 device voltage v 4.4 parameters rating operating case temperature - 40 to + 85 c storage temperature - 40 to + 150 c de vice voltage +5 v operating junction temper a ture + 150 c input rf power ( cw, 50ohm matched)* 20 dbm * please find the max. input power data from http://www.asb.co.kr/pdf/maximum_in put_power_analysis.pdf feature s description absolute maximum ratings same circuit over 800~3500 mhz 12.8 db gain a t 1950 mhz 19.5 dbm p1db at 1950 mhz 34.5 dbm output ip3 at 1950 mhz 0.9 db nf at 1950 mhz mttf > 100 years single supply the ASL09S, a wideband linear low noise amplifier mmic, has a low noise and high linearity at low bias current, being suitable for use in both receiver and transmitter of telecommunic a tion systems up to 3.5 ghz. s11 down to C 18 db is easily achieved for low noise application to provide a good productivity. the amplifier is available in a n sot - 89 package and pas s- es through the stringent dc, rf, and reliabi l ity tests. application circuit 800 ~ 3500 mhz 800 ~ 3500 mhz(3v) tetra (380~460mhz) produ ct specifications typical perfor m ance ASL09S package style: sot - 89
2 / 7 asb inc. sales@asb .co.kr tel: +82 - 42 - 528 - 7223 may 2012 as l09s 5 - 40 00 mhz high linearity lna mmic pin no. function 1 rf in 2 gnd 3 rf out / bias mounting recommendation (in mm) outline drawing esd classification hbm class 1a voltage level: 400 v mm class a voltage level: 50 v caution: esd - sensitive device! moisture sensitivity level (msl) level 3 at 260 c reflow esd classification & moisture sensitivity level symbols dimensions (in mm) min nom max a 1.40 1.50 1.60 l 0.89 1.04 1.20 b 0.36 0.42 0.48 b1 0.41 0.47 0.53 c 0.38 0.40 0.43 d 4.40 4.50 4.60 d1 1.40 1.60 1.75 e 3.64 --- 4.25 e1 2.40 2.50 2.60 e1 2.90 3.00 3.10 h 0.35 0.40 0.45 s 0.65 0.75 0.85 e 1.40 1.50 1.60 as l09s pxxxx lot no. part no. note : 1. the number and size of ground via holes in a circuit board is critical for thermal and rf grounding consi d erations. 2. we recommend that the ground via holes be placed on the bottom of the lead pin 2 and exposed pad of the device for better rf and thermal performance, as shown in the drawing at the left side.
3 / 7 asb inc. sales@asb .co.kr tel: +82 - 42 - 528 - 7223 may 2012 as l09s 5 - 40 00 mhz high linearity lna mmic 1) oip3 is measured with two tones at an output power of +5 dbm/tone sep a- rated by 1 mhz. c1=82 pf l1=82 nh c2=82 pf rf in rf out c3=100 pf ASL09S c4=10 n f l2=18 nh vs=5 v r1 =15 w 0 500 1000 1500 2000 2500 3000 3500 4000 -30 -25 -20 -15 -10 -5 0 s11 (db) frequency (mhz) -40 o c 25 o c 85 o c 0 500 1000 1500 2000 2500 3000 3500 4000 0 5 10 15 20 25 gain (db) frequency (mhz) -40 o c 25 o c 85 o c 0 500 1000 1500 2000 2500 3000 3500 4000 -20 -15 -10 -5 0 s22 (db) frequency (mhz) -40 o c 25 o c 85 o c 0 500 1000 1500 2000 2500 3000 3500 4000 0 1 2 3 4 5 stability factor frequency (mhz) board layout ( fr4, 40x40 mm 2 , 0.8t) schematic s - parameters & k - factor application circuit fr equency (mhz) 800 1950 2400 2700 3500 magnitude s21 (db) 19.3 12.8 11 10 7.5 magnitude s11 (db) - 18 - 18 - 20 - 20 - 18 magnitude s22 (db) - 10 - 10 - 9.5 - 9.5 - 9 output p1db (dbm) 19.5 19.5 20 19.5 20 output ip3 1) (dbm) 32 34.5 35.5 36.5 36 noise figure (d b) 0.8 0.9 1.1 1.2 1.5 device voltage (v) 4.4 4.4 4.4 4.4 4.4 current (ma) 45 45 45 45 45 800 ~ 3500 +5 v
4 / 7 asb inc. sales@asb .co.kr tel: +82 - 42 - 528 - 7223 may 2012 as l09s 5 - 40 00 mhz high linearity lna mmic -60 -40 -20 0 20 40 60 80 100 20 30 40 50 60 70 current (ma) temperature ( o c) -60 -40 -20 0 20 40 60 80 100 30 32 34 36 38 40 output ip3 (dbm) temperature ( o c) frequency = 1950 mhz 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 20 25 30 35 40 45 50 output ip3 (dbm) p out per tone (dbm) -40 o c 25 o c 85 o c -60 -40 -20 0 20 40 60 80 100 16 18 20 22 24 26 p1db (dbm) temperature ( o c) frequency = 1950 mhz -60 -40 -20 0 20 40 60 80 100 0.4 0.6 0.8 1.0 1.2 1.4 nf (db) temperature ( o c) frequency = 1950 mhz -60 -40 -20 0 20 40 60 80 100 10 11 12 13 14 15 16 gain (db) temperature ( o c) frequency = 1950 mhz p1db vs. temperature current vs. temperature output ip3 vs. tone power (frequency = 1950 mhz) output ip3 vs. temperature gain vs. temperatur e nf vs. temperature
5 / 7 asb inc. sales@asb .co.kr tel: +82 - 42 - 528 - 7223 may 2012 as l09s 5 - 40 00 mhz high linearity lna mmic 1) oip3 is measured with two tones at an output power of + 0 dbm/tone sep a- rated by 1 mhz. 0 500 1000 1500 2000 2500 3000 3500 4000 -30 -25 -20 -15 -10 -5 0 s11 (db) frequency (mhz) -40 o c 25 o c 85 o c 0 500 1000 1500 2000 2500 3000 3500 4000 -20 -15 -10 -5 0 s22 (db) frequency (mhz) -40 o c 25 o c 85 o c 0 500 1000 1500 2000 2500 3000 3500 4000 0 1 2 3 4 5 stability factor frequency (mhz) 0 500 1000 1500 2000 2500 3000 3500 4000 0 5 10 15 20 25 gain (db) frequency (mhz) -40 o c 25 o c 85 o c board layout ( fr4, 40x40 mm 2 , 0.8t) schematic s - parameters & k - factor application circuit frequency (mhz) 800 1950 2400 2700 3500 magnitude s21 (db) 19 12.6 10.8 9.8 7 magnitude s11 (db) - 18 - 17 - 18 - 18 - 18 magnitude s 22 (db) - 10 - 10 - 10 - 10 - 9 output p1db (dbm) 17.5 18 18 18 19.5 output ip3 1) (dbm) 28.5 30.5 32 33 31 noise figure (db) 0.8 0.95 1.15 1.2 5 1.5 device voltage (v) 3 3 3 3 3 current (ma) 28 28 28 28 28 800 ~ 3500 +3 v c1=82 pf l1=82 nh c2=82 pf rf in rf out c3=100 pf ASL09S c4=10 n f l2=18 nh vs=3 v r1 =85 k w
6 / 7 asb inc. sales@asb .co.kr tel: +82 - 42 - 528 - 7223 may 2012 as l09s 5 - 40 00 mhz high linearity lna mmic -60 -40 -20 0 20 40 60 80 100 26 28 30 32 34 36 output ip3 (dbm) temperature ( o c) frequency = 1950 mhz -60 -40 -20 0 20 40 60 80 100 0.4 0.6 0.8 1.0 1.2 1.4 nf (db) temperature ( o c) frequency = 1950 mhz -60 -40 -20 0 20 40 60 80 100 14 16 18 20 22 24 p1db (dbm) temperature ( o c) frequency = 1950 mhz -6 -4 -2 0 2 4 6 8 10 12 14 15 20 25 30 35 40 output ip3 (dbm) p out per tone (dbm) -40 o c 25 o c 85 o c -60 -40 -20 0 20 40 60 80 100 0 10 20 30 40 50 current (ma) temperature ( o c) -60 -40 -20 0 20 40 60 80 100 10 11 12 13 14 15 16 gain (db) temperature ( o c) frequency = 1950 mhz p1db vs. temperature current vs. temperature output ip3 vs. tone power (frequency = 1950 mhz) output ip3 vs. temperature gain vs. temperature nf vs. temperature
7 / 7 asb inc. sales@asb .co.kr tel: +82 - 42 - 528 - 7223 may 2012 as l09s 5 - 40 00 mhz high linearity lna mmic c1=100 pf l1=82 nh c2=100 pf rf in rf out c3=100 pf ASL09S c4=10 n f l2=82 nh vs=5 v r1 =15 w l3=18 nh 0 250 500 750 1000 0 5 10 15 20 25 gain (db) frequency (mhz) 0 250 500 750 1000 -25 -20 -15 -10 -5 0 s11 (db) frequency (mhz) 0 250 500 750 1000 -25 -20 -15 -10 -5 0 s22 (db) frequency (mhz) 0 500 1000 1500 2000 2500 3000 0 1 2 3 4 5 6 7 8 9 10 stability factor frequency [mhz] 1) oip3 is measured with two tones at an output power of +5 dbm/tone sep a- rated by 1 mhz. board layout ( fr4, 40x40 mm 2 , 0.8t) schematic s - parameters & k - factor application circuit frequency (mhz) 38 0 460 magnitude s21 (db) 23.1 22.5 magnitude s11 (db) - 15 - 18 magnitude s22 (db) - 14 - 15 output p1db (dbm) 19.5 19.5 output ip3 1) (dbm) 31.5 32 noise figure (db) 1.0 1.05 device voltage (v) 4.4 4.4 current (ma) 45 45 tetra 380 ~ 460 +5 v
|
