View 74LVC1G53DP_4680580.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1. general description the 74lvc1g53 is a low-power, low-voltage, high-speed, si-gate cmos device. the 74lvc1g53 provides one analog multiplexer/demultiplexer with a digital select input (s), two independent inputs/outputs (y0 and y1), a common input/output (z) and an active low enable input ( e). when pin e is high, the switch is turned off. schmitt-trigger action at the select and enable inputs makes the circuit tolerant of slower input rise and fall times across the entire v cc range from 1.65 v to 5.5 v. 2. features n wide supply voltage range from 1.65 v to 5.5 v n very low on resistance: u 7.5 w (typical) at v cc = 2.7 v u 6.5 w (typical) at v cc = 3.3 v u 6 w (typical) at v cc =5v n switch current capability of 32 ma n high noise immunity n cmos low-power consumption n ttl interface compatibility at 3.3 v n latch-up performance meets requirements of jesd 78 class i n esd protection: u hbm jesd22-a114e exceeds 2000 v u mm jesd22-a115-a exceeds 200 v u cdm jesd22-c101c exceeds 1000 v n control inputs accepts voltages up to 5 v n multiple package options n speci?ed from - 40 c to +85 c and from - 40 c to +125 c 74lvc1g53 2-channel analog multiplexer/demultiplexer rev. 03 29 august 2007 product data sheet
74lvc1g53_3 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 03 29 august 2007 2 of 22 nxp semiconductors 74lvc1g53 2-channel analog multiplexer/demultiplexer 3. ordering information 4. marking 5. functional diagram table 1. ordering information type number package temperature range name description version 74LVC1G53DP - 40 c to +125 c tssop8 plastic thin shrink small outline package; 8 leads; body width 3 mm; lead length 0.5 mm sot505-2 74lvc1g53dc - 40 c to +125 c vssop8 plastic very thin shrink small outline package; 8 leads; body width 2.3 mm sot765-1 74lvc1g53gt - 40 c to +125 c xson8 plastic extremely thin small outline package; no leads; 8 terminals; body 1 1.95 0.5 mm sot833-1 74lvc1g53gm - 40 c to +125 c xqfn8 plastic extremely thin quad ?at package; no leads; 8 terminals; body 1.6 1.6 0.5 mm sot902-1 table 2. marking type number marking code 74lvc1g53dc v53 74LVC1G53DP v53 74lvc1g53gt v53 74lvc1g53gm v53 fig 1. logic symbol 001aad386 s z e y0 y1 6 7 2 5 1 fig 2. logic diagram 001aad387 z y0 s y1 e
74lvc1g53_3 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 03 29 august 2007 3 of 22 nxp semiconductors 74lvc1g53 2-channel analog multiplexer/demultiplexer 6. pinning information 6.1 pinning 6.2 pin description fig 3. pin con?guration sot505-2 (tssop8) and sot765-1 (vssop8) fig 4. pin con?guration sot833-1 (xson8) 74lvc1g53 zv cc ey0 gnd y1 gnd s 001aad388 1 2 3 4 6 5 8 7 74lvc1g53 y1 y0 v cc s gnd e z gnd 001aad389 36 27 18 45 transparent top view fig 5. pin con?guration sot902-1 (xqfn8) 001aag459 e y1 z v cc gnd y0 gnd s transparent top view 3 6 4 1 5 8 7 2 terminal 1 index area 74lvc1g53 table 3. pin description symbol pin description sot505-2, sot765-1 and sot833-1 sot902-1 z 1 7 common output or input e 2 6 enable input (active low) gnd 3 5 ground (0 v) gnd 4 4 ground (0 v) s 5 3 select input
74lvc1g53_3 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 03 29 august 2007 4 of 22 nxp semiconductors 74lvc1g53 2-channel analog multiplexer/demultiplexer 7. functional description [1] h = high voltage level; l = low voltage level; x = dont care; z = high-impedance off-state. 8. limiting values [1] the minimum input voltage rating may be exceeded if the input current rating is observed. [2] the minimum and maximum switch voltage ratings may be exceeded if the switch clamping current rating is observed. [3] for the tssop8 and vssop8 packages: above 110 c the value of p tot derates linearly with 8 mw/k. for xson8 and xqfn8 packages: above 45 c the value of p tot derates linearly with 2.4 mw/k. y1 6 2 independent input or output y0 7 1 independent input or output v cc 8 8 supply voltage table 3. pin description continued symbol pin description sot505-2, sot765-1 and sot833-1 sot902-1 table 4. function table [1] input channel on s e l l y0 to z or z to y0 h l y1 to z or z to y1 x h z (switch off) table 5. limiting values in accordance with the absolute maximum rating system (iec 60134). voltages are referenced to gnd (ground = 0 v). symbol parameter conditions min max unit v cc supply voltage - 0.5 +6.5 v v i input voltage [1] - 0.5 +6.5 v i ik input clamping current v i < - 0.5 v or v i >v cc + 0.5 v - 50 - ma i sk switch clamping current v i < - 0.5 v or v i >v cc + 0.5 v - 50 ma v sw switch voltage enable and disable mode [2] - 0.5 v cc + 0.5 v i sw switch current v sw > - 0.5 v or v sw < v cc + 0.5 v - 50 ma i cc supply current - 100 ma i gnd ground current - 100 - ma t stg storage temperature - 65 +150 c p tot total power dissipation t amb = - 40 c to +125 c [3] - 250 mw
74lvc1g53_3 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 03 29 august 2007 5 of 22 nxp semiconductors 74lvc1g53 2-channel analog multiplexer/demultiplexer 9. recommended operating conditions [1] to avoid sinking gnd current from terminal z when switch current ?ows in terminal yn, the voltage drop across the bidirectio nal switch must not exceed 0.4 v. if the switch current ?ows into terminal z, no gnd current will ?ow from terminal yn. in this case, there is no limit for the voltage drop across the switch. [2] applies to control signal levels. 10. static characteristics table 6. recommended operating conditions symbol parameter conditions min typ max unit v cc supply voltage 1.65 - 5.5 v v i input voltage 0 - 5.5 v v sw switch voltage enable and disable mode [1] 0- v cc v t amb ambient temperature - 40 - +125 c d t/ d v input transition rise and fall rate v cc = 1.65 v to 2.7 v [2] - - 20 ns/v v cc = 2.7 v to 5.5 v [2] - - 10 ns/v table 7. static characteristics at recommended operating conditions; voltages are referenced to gnd (ground 0 v). symbol parameter conditions - 40 c to +85 c - 40 c to +125 c min typ [1] max min max unit v ih high-level input voltage v cc = 1.65 v to 1.95 v 0.65v cc - - 0.65v cc -v v cc = 2.3 v to 2.7 v 1.7 - - 1.7 - v v cc = 3 v to 3.6 v 2.0 - - 2.0 - v v cc = 4.5 v to 5.5 v 0.7v cc - - 0.7v cc -v v il low-level input voltage v cc = 1.65 v to 1.95 v - - 0.35v cc - 0.35v cc v v cc = 2.3 v to 2.7 v - - 0.7 - 0.7 v v cc = 3 v to 3.6 v - - 0.8 - 0.8 v v cc = 4.5 v to 5.5 v - - 0.3v cc 0.3v cc v i i input leakage current pin s and pin e; v i = 5.5 v or gnd; v cc = 0 v to 5.5 v [2] - 0.1 2- 10 m a i s(off) off-state leakage current v i = v ih or v il ; v cc = 5.5 v; see figure 6 [2] - 0.1 5- 20 m a i s(on) on-state leakage current v i = v ih or v il ; v cc = 5.5 v; see figure 7 [2] - 0.1 5- 20 m a i cc supply current v i = 5.5 v or gnd; v sw = gnd or v cc ; i o =0a; v cc = 1.65 v to 5.5 v [2] - 0.1 10 - 40 m a d i cc additional supply current pin s and pin e; v i =v cc - 0.6 v; i o = 0 a; v sw = gnd or v cc ; v cc = 5.5 v [2] - 5 500 - 5000 m a
74lvc1g53_3 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 03 29 august 2007 6 of 22 nxp semiconductors 74lvc1g53 2-channel analog multiplexer/demultiplexer [1] typical values are measured at t amb =25 c. [2] these typical values are measured at v cc = 3.3 v 10.1 test circuits c i input capacitance - 2.5 - - - pf c s(off) off-state capacitance - 6.0 - - - pf c s(on) on-state capacitance -18---pf table 7. static characteristics continued at recommended operating conditions; voltages are referenced to gnd (ground 0 v). symbol parameter conditions - 40 c to +85 c - 40 c to +125 c min typ [1] max min max unit v i =v cc or gnd; v o = gnd or v cc . fig 6. test circuit for measuring off-state leakage current v o i s 001aad390 s z e y0 y1 v cc gnd switch switch 1 1 2 2 v il v ih s v ih v ih e v i v il or v ih v ih v i =v cc or gnd and v o = open circuit. fig 7. test circuit for measuring on-state leakage current i s 001aad391 s z e y0 y1 v cc gnd v i v il or v ih v il switch 1 2v il v ih s v il v il e v o switch 1 2
74lvc1g53_3 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 03 29 august 2007 7 of 22 nxp semiconductors 74lvc1g53 2-channel analog multiplexer/demultiplexer 10.2 on resistance [1] typical values are measured at t amb =25 c and nominal v cc . [2] flatness is de?ned as the difference between the maximum and minimum value of on resistance measured at identical v cc and temperature. table 8. on resistance at recommended operating conditions; voltages are referenced to gnd (ground 0 v); for graphs see figure 9 to figure 14 . symbol parameter conditions - 40 c to +85 c - 40 c to +125 c unit min typ [1] max min max r on(peak) on resistance (peak) v i = gnd to v cc ; see figure 8 i sw = 4 ma; v cc = 1.65 v to 1.95 v - 34.0 130 - 195 w i sw = 8 ma; v cc = 2.3 v to 2.7 v - 12.0 30 - 45 w i sw = 12 ma; v cc = 2.7 v - 10.4 25 - 38 w i sw = 24 ma; v cc = 3 v to 3.6 v - 7.8 20 - 30 w i sw = 32 ma; v cc = 4.5 v to 5.5 v - 6.2 15 - 23 w r on(rail) on resistance (rail) v i = gnd; see figure 8 i sw = 4 ma; v cc = 1.65 v to 1.95 v - 8.2 18 - 27 w i sw = 8 ma; v cc = 2.3 v to 2.7 v - 7.1 16 - 24 w i sw = 12 ma; v cc = 2.7 v - 6.9 14 - 21 w i sw = 24 ma; v cc = 3 v to 3.6 v - 6.5 12 - 18 w i sw = 32 ma; v cc = 4.5 v to 5.5 v - 5.8 10 - 15 w v i =v cc ; see figure 8 i sw = 4 ma; v cc = 1.65 v to 1.95 v - 10.4 30 - 45 w i sw = 8 ma; v cc = 2.3 v to 2.7 v - 7.6 20 - 30 w i sw = 12 ma; v cc = 2.7 v - 7.0 18 - 27 w i sw = 24 ma; v cc = 3 v to 3.6 v - 6.1 15 - 23 w i sw = 32 ma; v cc = 4.5 v to 5.5 v - 4.9 10 - 15 w r on(?at) on resistance (?atness) v i = gnd to v cc [2] i sw = 4 ma; v cc = 1.65 v to 1.95 v - 26.0 - - - w i sw = 8 ma; v cc = 2.3 v to 2.7 v - 5.0 - - - w i sw = 12 ma; v cc = 2.7 v - 3.5 - - - w i sw = 24 ma; v cc = 3 v to 3.6 v - 2.0 - - - w i sw = 32 ma; v cc = 4.5 v to 5.5 v - 1.5 - - - w
74lvc1g53_3 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 03 29 august 2007 8 of 22 nxp semiconductors 74lvc1g53 2-channel analog multiplexer/demultiplexer 10.3 on resistance test circuit and graphs r on = v sw / i sw . fig 8. test circuit for measuring on resistance i sw v sw 001aad392 s z e y0 y1 v cc gnd switch switch 1 1 2 2 v ih v il s v il v il e v i v il or v ih v il (1) v cc = 1.8 v. (2) v cc = 2.5 v. (3) v cc = 2.7 v. (4) v cc = 3.3 v. (5) v cc = 5.0 v. fig 9. typical on resistance as a function of input voltage; t amb = 25 c v i (v) 05 4 23 1 mna673 20 10 30 40 r on ( w ) 0 (1) (2) (3) (4) (5)
74lvc1g53_3 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 03 29 august 2007 9 of 22 nxp semiconductors 74lvc1g53 2-channel analog multiplexer/demultiplexer (1) t amb = 125 c. (2) t amb =85 c. (3) t amb =25 c. (4) t amb = - 40 c. (1) t amb = 125 c. (2) t amb =85 c. (3) t amb =25 c. (4) t amb = - 40 c. fig 10. on resistance as a function of input voltage; v cc = 1.8 v fig 11. on resistance as a function of input voltage; v cc = 2.5 v v i (v) 0 2.0 1.6 0.8 1.2 0.4 001aaa712 25 35 15 45 55 r on ( w ) 5 (4) (3) (2) (1) v i (v) 0 2.5 2.0 1.0 1.5 0.5 001aaa708 9 11 7 13 15 r on ( w ) 5 (1) (2) (3) (4) (1) t amb = 125 c. (2) t amb =85 c. (3) t amb =25 c. (4) t amb = - 40 c. (1) t amb = 125 c. (2) t amb =85 c. (3) t amb =25 c. (4) t amb = - 40 c. fig 12. on resistance as a function of input voltage; v cc = 2.7 v fig 13. on resistance as a function of input voltage; v cc = 3.3 v 001aaa709 v i (v) 0 3.0 2.0 1.0 2.5 1.5 0.5 9 7 11 13 r on ( w ) 5 (1) (2) (3) (4) v i (v) 04 3 12 001aaa710 6 8 10 r on ( w ) 4 (1) (2) (3) (4)
74lvc1g53_3 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 03 29 august 2007 10 of 22 nxp semiconductors 74lvc1g53 2-channel analog multiplexer/demultiplexer 11. dynamic characteristics (1) t amb = 125 c. (2) t amb =85 c. (3) t amb =25 c. (4) t amb = - 40 c. fig 14. on resistance as a function of input voltage; v cc = 5.0 v v i (v) 05 4 23 1 001aaa711 5 4 6 7 r on ( w ) 3 (2) (4) (1) (3) table 9. dynamic characteristics at recommended operating conditions; voltages are referenced to gnd (ground = 0 v); for load circuit see figure 17 . symbol parameter conditions - 40 c to +85 c - 40 c to +125 c unit min typ [1] max min max t pd propagation delay z to yn or yn to z; see figure 15 [2] [3] v cc = 1.65 v to 1.95 v - - 2 - 2.5 ns v cc = 2.3 v to 2.7 v - - 1.2 - 1.5 ns v cc = 2.7 v - - 1.0 - 1.25 ns v cc = 3.0 v to 3.6 v - - 0.8 - 1.0 ns v cc = 4.5 v to 5.5 v - - 0.6 - 0.8 ns
74lvc1g53_3 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 03 29 august 2007 11 of 22 nxp semiconductors 74lvc1g53 2-channel analog multiplexer/demultiplexer [1] typical values are measured at t amb =25 c and nominal v cc . [2] t pd is the same as t plh and t phl . [3] propagation delay is the calculated rc time constant of the typical on resistance of the switch and the speci?ed capacitance when driven by an ideal voltage source (zero output impedance). [4] t en is the same as t pzh and t pzl [5] t dis is the same as t plz and t phz t en enable time s to z or yn; see figure 16 [4] v cc = 1.65 v to 1.95 v 2.6 6.7 10.3 2.6 12.9 ns v cc = 2.3 v to 2.7 v 1.9 4.1 6.4 1.9 8.0 ns v cc = 2.7 v 1.9 4.0 5.5 1.8 7.0 ns v cc = 3.0 v to 3.6 v 1.8 3.4 5.0 1.8 6.3 ns v cc = 4.5 v to 5.5 v 1.3 2.6 3.8 1.3 4.8 ns e to z or yn; see figure 16 [4] v cc = 1.65 v to 1.95 v 1.9 4.0 7.3 1.9 9.2 ns v cc = 2.3 v to 2.7 v 1.4 2.5 4.4 1.4 5.5 ns v cc = 2.7 v 1.1 2.6 3.9 1.1 4.9 ns v cc = 3.0 v to 3.6 v 1.2 2.2 3.8 1.2 4.8 ns v cc = 4.5 v to 5.5 v 1.0 1.7 2.6 1.0 3.3 ns t dis disable time s to z or yn; see figure 16 [5] v cc = 1.65 v to 1.95 v 2.1 6.8 10.0 2.1 12.5 ns v cc = 2.3 v to 2.7 v 1.4 3.7 6.1 1.4 7.7 ns v cc = 2.7 v 1.4 4.9 6.2 1.4 7.8 ns v cc = 3.0 v to 3.6 v 1.1 4.0 5.4 1.1 6.8 ns v cc = 4.5 v to 5.5 v 1.0 2.9 3.8 1.0 4.8 ns e to z or yn; see figure 16 [5] v cc = 1.65 v to 1.95 v 2.3 5.6 8.6 2.3 11.0 ns v cc = 2.3 v to 2.7 v 1.2 3.2 4.8 1.2 6.0 ns v cc = 2.7 v 1.4 4.0 5.2 1.4 6.5 ns v cc = 3.0 v to 3.6 v 2.0 3.7 5.0 2.0 6.3 ns v cc = 4.5 v to 5.5 v 1.3 2.9 3.8 1.3 4.8 ns table 9. dynamic characteristics continued at recommended operating conditions; voltages are referenced to gnd (ground = 0 v); for load circuit see figure 17 . symbol parameter conditions - 40 c to +85 c - 40 c to +125 c unit min typ [1] max min max
74lvc1g53_3 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 03 29 august 2007 12 of 22 nxp semiconductors 74lvc1g53 2-channel analog multiplexer/demultiplexer 11.1 waveforms and test circuits measurement points are given in t ab le 10 . logic levels: v ol and v oh are typical output voltage levels that occur with the output load. fig 15. input (yn or z) to output (z or yn) propagation delays t plh t phl v m v m v m v m gnd v i v oh v ol yn or z input z or yn output 001aac361 measurement points are given in t ab le 10 . logic levels: v ol and v oh are typical output voltage levels that occur with the output load. fig 16. enable and disable times v m v i gnd v cc v ol v oh gnd s, e input output low to off off to low output high to off off to high v m 001aad393 v m t pzl t phz t pzh v x v y switch disabled switch enabled switch enabled z, yn z, yn t plz table 10. measurement points supply voltage input output v cc v m v m v x v y 1.65 v to 2.7 v 0.5v cc 0.5v cc v ol + 0.15 v v oh - 0.15 v 2.7 v to 5.5 v 0.5v cc 0.5v cc v ol + 0.3 v v oh - 0.3 v
74lvc1g53_3 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 03 29 august 2007 13 of 22 nxp semiconductors 74lvc1g53 2-channel analog multiplexer/demultiplexer 11.2 additional dynamic characteristics test data is given in t ab le 11 . de?nitions test circuit: r t = termination resistance (should be equal to output impedance z o of the pulse generator). c l = load capacitance (including jig and probe capacitance). r l = load resistance. v ext = external voltage for measuring switching times. fig 17. load circuit for switching times v ext v cc v i v o mna616 dut c l r t r l r l g table 11. test data supply voltage input load v ext v cc v i t r , t f c l r l t plh , t phl t pzh , t phz t pzl , t plz 1.65 v to 1.95 v v cc 2.0 ns 30 pf 1 k w open gnd 2v cc 2.3 v to 2.7 v v cc 2.0 ns 30 pf 500 w open gnd 2v cc 2.7 v v cc 2.5 ns 50 pf 500 w open gnd 2v cc 3 v to 3.6 v v cc 2.5 ns 50 pf 500 w open gnd 2v cc 4.5 v to 5.5 v v cc 2.5 ns 50 pf 500 w open gnd 2v cc table 12. additional dynamic characteristics at recommended operating conditions; voltages are referenced to gnd (ground = 0 v); t amb =25 c. symbol parameter conditions min typ max unit thd total harmonic distortion f i = 600 hz to 20 khz; r l = 600 w ; c l = 50 pf; v i = 0.5 v (p-p); see figure 18 v cc = 1.65 v - 0.260 - % v cc = 2.3 v - 0.078 - % v cc = 3.0 v - 0.078 - % v cc = 4.5 v - 0.078 - % f (-3db) - 3 db frequency response r l =50 w ; c l = 5 pf; see figure 19 v cc = 1.65 v - 200 - mhz v cc = 2.3 v - 300 - mhz v cc = 3.0 v - 300 - mhz v cc = 4.5 v - 300 - mhz
74lvc1g53_3 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 03 29 august 2007 14 of 22 nxp semiconductors 74lvc1g53 2-channel analog multiplexer/demultiplexer 11.3 test circuits a iso isolation (off-state) r l =50 w ; c l = 5 pf; f i = 10 mhz; see figure 20 v cc = 1.65 v - - 42 - db v cc = 2.3 v - - 42 - db v cc = 3.0 v - - 40 - db v cc = 4.5 v - - 40 - db q inj charge injection c l = 0.1 nf; v gen =0v; r gen =0 w ; f i = 1 mhz; r l =1m w ; see figure 21 v cc = 1.8 v - 3.3 - pc v cc = 2.5 v - 4.1 - pc v cc = 3.3 v - 5.0 - pc v cc = 4.5 v - 6.4 - pc v cc = 5.5 v - 7.5 - pc table 12. additional dynamic characteristics continued at recommended operating conditions; voltages are referenced to gnd (ground = 0 v); t amb =25 c. symbol parameter conditions min typ max unit fig 18. test circuit for measuring total harmonic distortion d 001aad394 600 w 10 m f 0.1 m f s z y0 y1 v cc 0.5v cc gnd c l r l switch switch 1 1 2 2 v ih v il s v il v il e f i v il or v ih e v il adjust f i voltage to obtain 0 dbm level at output. increase f i frequency until db meter reads - 3db. fig 19. test circuit for measuring the frequency response when switch is in on-state db 001aad395 50 w 0.1 m f s z e y0 y1 v cc 0.5v cc gnd c l r l switch switch 1 1 2 2 v ih v il s v il v il e f i v il or v ih v il
74lvc1g53_3 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 03 29 august 2007 15 of 22 nxp semiconductors 74lvc1g53 2-channel analog multiplexer/demultiplexer adjust f i voltage to obtain 0 dbm level at input. fig 20. test circuit for measuring isolation (off-state) db 001aad396 50 w r l 0.1 m f s z e y0 y1 v cc 0.5v cc 0.5v cc gnd c l r l switch switch 1 1 2 2 v il v ih s v ih v ih e f i v il or v ih v ih a. test circuit b. input and output pulse de?nitions q inj = d v o c l . d v o = output voltage variation. r gen = generator resistance. v gen = generator voltage. fig 21. test circuit for measuring charge injection 001aad398 s z y0 y1 r l c l v cc gnd r gen v gen switch 1 2 v i v o e v il g 001aac478 d v o off on off logic input v o (s)
74lvc1g53_3 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 03 29 august 2007 16 of 22 nxp semiconductors 74lvc1g53 2-channel analog multiplexer/demultiplexer 12. package outline fig 22. package outline sot505-2 (tssop8) unit a 1 a max. a 2 a 3 b p l h e l p wy v ce d (1) e (1) z (1) q references outline version european projection issue date iec jedec jeita mm 0.15 0.00 0.95 0.75 0.38 0.22 0.18 0.08 3.1 2.9 3.1 2.9 0.65 4.1 3.9 0.70 0.35 8 0 0.13 0.1 0.2 0.5 dimensions (mm are the original dimensions) note 1. plastic or metal protrusions of 0.15 mm maximum per side are not included. 0.47 0.33 sot505-2 - - - 02-01-16 w m b p d z e 0.25 14 8 5 q a 2 a 1 l p (a 3 ) detail x a l h e e c v m a x a y 2.5 5 mm 0 scale tssop8: plastic thin shrink small outline package; 8 leads; body width 3 mm; lead length 0.5 mm sot505-2 1.1 pin 1 index
74lvc1g53_3 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 03 29 august 2007 17 of 22 nxp semiconductors 74lvc1g53 2-channel analog multiplexer/demultiplexer fig 23. package outline sot765-1 (vssop8) unit a 1 a max. a 2 a 3 b p l h e l p wy v ce d (1) e (2) z (1) q references outline version european projection issue date iec jedec jeita mm 0.15 0.00 0.85 0.60 0.27 0.17 0.23 0.08 2.1 1.9 2.4 2.2 0.5 3.2 3.0 0.4 0.1 8 0 0.13 0.1 0.2 0.4 dimensions (mm are the original dimensions) notes 1. plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. plastic or metal protrusions of 0.25 mm maximum per side are not included. 0.40 0.15 q 0.21 0.19 sot765-1 mo-187 02-06-07 w m b p d z e 0.12 14 8 5 q a 2 a 1 q l p (a 3 ) detail x a l h e e c v m a x a y 2.5 5 mm 0 scale vssop8: plastic very thin shrink small outline package; 8 leads; body width 2.3 mm sot765-1 1 pin 1 index
74lvc1g53_3 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 03 29 august 2007 18 of 22 nxp semiconductors 74lvc1g53 2-channel analog multiplexer/demultiplexer fig 24. package outline sot833-1 (xson8) terminal 1 index area references outline version european projection issue date iec jedec jeita sot833-1 - - - mo-252 - - - sot833-1 04-07-22 04-11-09 dimensions (mm are the original dimensions) xson8: plastic extremely thin small outline package; no leads; 8 terminals; body 1 x 1.95 x 0.5 mm d e e 1 e a 1 b l l 1 e 1 e 1 0 1 2 mm scale notes 1. including plating thickness. 2. can be visible in some manufacturing processes. unit mm 0.25 0.17 2.0 1.9 0.35 0.27 a 1 max b e 1.05 0.95 d ee 1 l 0.40 0.32 l 1 0.5 0.6 a (1) max 0.5 0.04 1 8 2 7 3 6 4 5 8 (2) 4 (2) a
74lvc1g53_3 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 03 29 august 2007 19 of 22 nxp semiconductors 74lvc1g53 2-channel analog multiplexer/demultiplexer fig 25. package outline sot902-1 (xqfn8) references outline version european projection issue date iec jedec jeita sot902-1 mo-255 - - - - - - sot902-1 05-11-16 05-11-25 unit a max mm 0.5 a 1 0.25 0.15 0.05 0.00 1.65 1.55 0.35 0.25 0.15 0.05 dimensions (mm are the original dimensions) xqfn8: plastic extremely thin quad flat package; no leads; 8 terminals; body 1.6 x 1.6 x 0.5 mm b dl e 1 1.65 1.55 e e l 1 v 0.1 0.55 0.5 w 0.05 y 0.05 0.05 y 1 0 1 2 mm scale x c y c y 1 terminal 1 index area terminal 1 index area b a d e detail x a a 1 b 8 7 6 5 e 1 e 1 e e a c b ? v m c ? w m 4 1 2 3 l l 1 metal area not for soldering
74lvc1g53_3 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 03 29 august 2007 20 of 22 nxp semiconductors 74lvc1g53 2-channel analog multiplexer/demultiplexer 13. abbreviations 14. revision history table 13. abbreviations acronym description cmos complementary metal oxide semiconductor ttl transistor-transistor logic hbm human body model esd electrostatic discharge mm machine model cdm charged device model dut device under test table 14. revision history document id release date data sheet status change notice supersedes 74lvc1g53_3 20070829 product data sheet - 74lvc1g53_2 modi?cations: ? the format of this data sheet has been redesigned to comply with the new identity guidelines of nxp semiconductors. ? legal texts have been adapted to the new company name where appropriate. ? added type number 74lvc1g53gm (xqfn8/sot902-1 package). ? section 2 f eatures : added: switch handling capability of 32 ma. ? section 10 static char acter istics : changed: conditions for input leakage and supply current. ? section 11.2 additional dynamic char acter istics : removed: crosstalk between switches removed from additional characteristics table. changed: typical values of the charge injection. 74lvc1g53_2 20060410 product data sheet - 74lvc1g53_1 74lvc1g53_1 20060110 product data sheet - -
74lvc1g53_3 ? nxp b.v. 2007. all rights reserved. product data sheet rev. 03 29 august 2007 21 of 22 nxp semiconductors 74lvc1g53 2-channel analog multiplexer/demultiplexer 15. legal information 15.1 data sheet status [1] please consult the most recently issued document before initiating or completing a design. [2] the term short data sheet is explained in section de?nitions. [3] the product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple dev ices. the latest product status information is available on the internet at url http://www .nxp .com . 15.2 de?nitions draft the document is a draft version only. the content is still under internal review and subject to formal approval, which may result in modi?cations or additions. nxp semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. short data sheet a short data sheet is an extract from a full data sheet with the same product type number(s) and title. a short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. for detailed and full information see the relevant full data sheet, which is available on request via the local nxp semiconductors sales of?ce. in case of any inconsistency or con?ict with the short data sheet, the full data sheet shall prevail. 15.3 disclaimers general information in this document is believed to be accurate and reliable. however, nxp semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. right to make changes nxp semiconductors reserves the right to make changes to information published in this document, including without limitation speci?cations and product descriptions, at any time and without notice. this document supersedes and replaces all information supplied prior to the publication hereof. suitability for use nxp semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of a nxp semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. nxp semiconductors accepts no liability for inclusion and/or use of nxp semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customers own risk. applications applications that are described herein for any of these products are for illustrative purposes only. nxp semiconductors makes no representation or warranty that such applications will be suitable for the speci?ed use without further testing or modi?cation. limiting values stress above one or more limiting values (as de?ned in the absolute maximum ratings system of iec 60134) may cause permanent damage to the device. limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the characteristics sections of this document is not implied. exposure to limiting values for extended periods may affect device reliability. terms and conditions of sale nxp semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www .nxp .com/pro? le/ter ms , including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by nxp semiconductors. in case of any inconsistency or con?ict between information in this document and such terms and conditions, the latter will prevail. no offer to sell or license nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. 15.4 trademarks notice: all referenced brands, product names, service names and trademarks are the property of their respective owners. 16. contact information for additional information, please visit: http://www .nxp.com for sales of?ce addresses, send an email to: salesad dresses@nxp.com document status [1] [2] product status [3] de?nition objective [short] data sheet development this document contains data from the objective speci?cation for product development. preliminary [short] data sheet quali?cation this document contains data from the preliminary speci?cation. product [short] data sheet production this document contains the product speci?cation.
nxp semiconductors 74lvc1g53 2-channel analog multiplexer/demultiplexer ? nxp b.v. 2007. all rights reserved. for more information, please visit: http://www.nxp.com for sales office addresses, please send an email to: salesaddresses@nxp.com date of release: 29 august 2007 document identifier: 74lvc1g53_3 please be aware that important notices concerning this document and the product(s) described herein, have been included in section legal information. 17. contents 1 general description . . . . . . . . . . . . . . . . . . . . . . 1 2 features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 3 ordering information . . . . . . . . . . . . . . . . . . . . . 2 4 marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 5 functional diagram . . . . . . . . . . . . . . . . . . . . . . 2 6 pinning information . . . . . . . . . . . . . . . . . . . . . . 3 6.1 pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 6.2 pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 7 functional description . . . . . . . . . . . . . . . . . . . 4 8 limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 4 9 recommended operating conditions. . . . . . . . 5 10 static characteristics. . . . . . . . . . . . . . . . . . . . . 5 10.1 test circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 10.2 on resistance . . . . . . . . . . . . . . . . . . . . . . . . . . 7 10.3 on resistance test circuit and graphs. . . . . . . . 8 11 dynamic characteristics . . . . . . . . . . . . . . . . . 10 11.1 waveforms and test circuits . . . . . . . . . . . . . . 12 11.2 additional dynamic characteristics . . . . . . . . . 13 11.3 test circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 12 package outline . . . . . . . . . . . . . . . . . . . . . . . . 16 13 abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 20 14 revision history . . . . . . . . . . . . . . . . . . . . . . . . 20 15 legal information. . . . . . . . . . . . . . . . . . . . . . . 21 15.1 data sheet status . . . . . . . . . . . . . . . . . . . . . . 21 15.2 de?nitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 15.3 disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 15.4 trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 16 contact information. . . . . . . . . . . . . . . . . . . . . 21 17 contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

▲Up To Search▲

Price & Availability of 74LVC1G53DP

	To Download 74LVC1G53DP Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .