evaluation board user guide UG-127 one technology way ? p. o . box 9106 ? norwood, ma 02062 - 9106, u.s.a. ? tel: 781.329.4700 ? fax: 781.461.3113 ? www.analog.com evaluation board for high speed op amps offered in 5- lead sot - 23 and 6- lead sot - 23 packages please see the last page for an important warning and legal terms and conditions . rev. a | page 1 of 8 features enables quick breadboarding/prototyping user - defined circuit configuration edge - mounted sma connector provisions easy connection to test equipment and other circuits rohs compliant general description the analog devices, inc. , 5- lead and 6 -lead, s ot - 23 high speed evaluation board is designed to help customers quickly prototype new op amp circuits and reduce design time. the evaluation board can be used with almost any analog devices op amp in various configurations and applications. the evaluation board is a bare board (that is, there are no components or amplifiers soldered to the board, these must be ordered separately). figure 1 shows the component side of the evaluation board, and figure 2 shows the circuit side of the evaluation board. the evaluation board is a 2 - layer pcb that accepts sma con - nectors on the input and output for efficient connection to test equipment. the evaluation board can also accommodate a n sma connector for the disable pin. the ground plane, component placement, and supply bypassing are laid out to minimize parasitic inductances and capacitances. the evaluation board components are primarily smt 1206 case size, with the exception of the el ectrolytic bypass capacitors (c1, c4), which are 3528 case size. there are two options for supply bypassing. the first is connecting additional shunt capacitors (c2, c5) in parallel with the electrolytic capacitors (c1, c4) from each supply to ground. this technique of power supply bypassing provides wideband rejection of unwanted noise on the supply lines. the second approach to supply bypassing is to connect one capacitor (c6) between the supply rails. this method uses fewer components and can improve the psrr at higher frequencies. optimal bypassing is circuit dependent and therefore must be eval uated by the designer. figure 3 sho ws the eva luation board schematic. figure 4 and fi gure 6 show the evaluation board assembly drawings. the pcb layout pattern for the component side and the circuit side is shown in figure 5 and figure 7 . evaluation board , component and circui t side s 08981-001 notes 1. the e v alu a tion board silkscreen p art number labeling on your board m ay be different from wh a t is shown here. figure 1 . component side of evaluation board 08981-002 notes 1. the e v alu a tion board silkscreen p art number labeling on your board m ay be different from wh a t is shown here. figure 2. circuit side of evaluation board
UG-127 evaluation board user guide rev. a | page 2 of 8 table of contents features .............................................................................................. 1 general description ......................................................................... 1 evaluation board, component and circuit sides ........................ 1 revision histo ry ............................................................................... 2 evaluation board schematic ............................................................3 evaluation board assembly drawings and layout patterns .......4 ordering information .......................................................................5 bill of materials ..............................................................................5 revision history 5 /11 rev . 0 to rev. a changes to user guide title, general description section, figure 1 caption, and figure 2 caption ........................................ 1 changed evaluation board schematic and layout section to evaluation board schematic section ............................................. 3 changes to figure 3 caption ........................................................... 3 added evaluation board assembly drawings and layout patterns section ................................................................................ 4 changes to figure 4 through figure 7 ........................................... 4 4/ 10 rev ision 0: initial version
evaluation board user guide UG-127 rev. a | page 3 of 8 evaluation board sch ematic 08981-003 * = user defined. agnd agnd agnd agnd agnd c5* c6* c2* +vs gnd4 gnd3 gnd2 gnd1 dis agnd agnd agnd agnd agnd in+ in? tp1 vout 6 5 4 3 2 1 dut vout ?vs dis +vs sot23_6 r2* vout r5* r3* r4* +vs ?vs out r8* r7* r1* r6* r9* +vs ?vs ?vs + + ? + c1 10f c4 10f ?in +in figure 3. 5- lead sot - 23 and 6 - lead sot - 23 evaluation board schematic
UG-127 evaluation board user guide rev. a | page 4 of 8 evaluation b oard assembly drawings and layout patterns 08981-004 figure 4 . board assembly drawing, component side 08981-006 figure 5 . board layout pattern, component side 08981-005 figure 6. board assembly drawing, circuit side 08981-007 figure 7 . board layout pattern, circuit side
evaluation board user guide UG-127 rev. a | page 5 of 8 ordering information bill of materials table 1 . quantity reference designator description package 7 +vs, ? vs, gnd1, gnd2, gnd3, gnd4, tp1 test point tp1 2 c1, c4 10 f capacitor c352 8 3 c2, c5, c6 user - defined capacitor c1206 1 dis sma_hd smacon 1 dut 5- lead sot -23 or 6- lead sot -23 sot -23- 5 or sot -23 -6 3 in+, in ? , out sma / smt sma / smt 9 r1 to r9 user - defined resistor r1206
UG-127 evaluation board user guide rev. a | page 6 of 8 notes
evaluation board user guide UG-127 rev. a | page 7 of 8 notes
UG-127 evaluation board user guide rev. a | page 8 of 8 notes esd caution esd (electrostatic discharge) sensitive device . charged devices and circuit boards can discharge without detection. although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy esd. therefore, proper esd p recautions should be taken to avoid performance degradation or loss of functionality. legal terms and conditions by using the evaluation board discussed herein (together with any tools, components documentation or support materials, the evaluation board ), you are agreeing to be bound by the terms and conditions set forth below (agreement) unless you have purchased the evaluation board, in which case the analog devices standard terms and conditions of sale shall govern. do not use the evaluation board u ntil you have read and agreed to the agreement. your use of the evaluation board shall signify your acceptance of the agreement. this agreement is made by and between you (customer) and analog devices, inc. (adi), with its principal place of business at one technology way, norwood, ma 02062, usa. subject to the terms and conditions of the agreement, adi hereby grants to cus tomer a free, limited, personal, temporary, non - exclusive, non - sublicensable, non - transferable license to use the evaluation board for evaluation purposes only. customer understands and agrees that the evaluation board is provided for the sole and exclusive purpose referenced above, and agrees not to use the evaluation board for any other purpose. furthe rmore, the license granted is e xpressly made subject to the following additional limitations: customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the evaluation bo ard; and (ii) permit any third party to access the evaluation board. as used here in, the term third party includes any entity other than adi, customer, their employees, affiliates and in - house consultants. the evaluation board is not sold to customer; all rights not expressly granted herein, including ownership of the evaluation boar d, are reserved by adi. confidentiality. this agreement and the evaluation board shall all be considered the confidential and proprietary information of adi. customer may not disclose or transfer any portion of the evaluation board to any other party for a ny reason. upon discontinuation of use of the evaluation board or termination of this agreement, customer agrees to promptly return the evaluation board to adi. additional restrictions. customer may not disassemble, decompile or reverse engi neer chips on t he evaluation board. customer shall inform adi of any occurred damages or any modifications or alterations it makes to the evaluation board, including but not limited to soldering or any other activity that affects the material content of the evaluation bo ard. modifications to the evaluation board must comply with applicable law, including but not limited to the rohs directive. termi nation. adi may terminate this agreement at any time upon giving written notice to customer. customer agrees to return to adi the evaluation board at that time. limitation of liability. the evaluation board provided hereunder is provided as is and a di makes no warranties or representations of any kind with respect to it. adi specifically disclaims any representations, endorseme nts, guarantees, or warranties, express or implied, related to the evaluation board including, but not limited to, the implied warranty of merchantability, title, fitness for a particul ar purpose or noninfringement of intellectual property rights. in no ev ent will adi and its licensors be liable for any incidental, special, indirect, or consequential damages resulting from custo mers possession or use of the evaluation board, including but not limited to lost profits, delay costs, labor costs or loss of goo dwill. adis total liability from any and all causes shall be limited to the amount of one hundred us dollars ($100.00). export. customer agrees that it will not directly or indirectly export the evalua tion board to another country, and that it will comply with all applicable united states federal laws and regulations relating to exports. governing law. this agreement shall be governed by and construed in accordance with the substantive laws of the commonwealth of massachusetts (excluding conflict of law rules). any legal action regarding this agreement will be heard in the state or federal courts having jurisdiction in suffolk county, massachusetts, and customer hereby submits to the personal jurisdiction and venue of such courts. the united nations conven tion on contracts for the international sale of goods shall not apply to this agreement and is expressly disclaimed. ? 2010 C 2011 analog devices, inc. all rights reserved. trademarks and registered trademarks are the property of their respective owners. ug08981 -0- 5 /11(a)
|
