micropower direct 292 page street suite d stoughton, ma 02072 usa t: (781) 344-8226 f: (781) 344-8481 e: sales@micropowerdirect.com w: www.micropowerdirect.com low cost, 1w minidip single & dual output dc/dc con vert ers key features: ? 1w output power ? compact minidip case ? ul approved (file e245422) ? single & dual outputs ? 1,000 vdc isolation ? >3.5 mhour mtbf ? 24 standard models ? lowest cost!! l c t 1 w m i i d i p G100E series input parameter conditions min. typ. max. units input voltage range 5 vdc input 4.5 5.0 5.5 vdc 12 vdc input 10.8 12.0 13.2 24 vdc input 21.6 24.0 26.4 input filter internal capacitor reverse polarity input current 0.3 a output parameter conditions min. typ. max. units output voltage accuracy 1.0 3.0 % output voltage balance dual output , balanced loads 0.1 1.0 % line regulation for vin change of 1% 1.2 % load regulation (note 1) see model selection guide ripple & noise (20 mhz) (note 2) 50 75 mv p - p output power protection 120 % temperature coef? cient 0.02 0.03 %/oc output short circuit momentary (1.0 sec.) general parameter conditions min. typ. max. units isolation voltage 60 seconds 1,000 vdc isolation resistance 500 vdc 1,000 m isolation capacitance 100 khz, 1v 60 pf switching frequency 100 khz environmental parameter conditions min. typ. max. units operating temperature range ambient -40 +25 +85 oc storage temperature range -55 +125 oc cooling free air convection humidity rh, non-condensing 95 % physical case size 0.80 x 0.40 x 0.25 inches (20.4 x 10.2 x 6.5 mm) case material non-conductive black plastic (ul94-v0) weight 0.07 oz (2.1g) reliability speci? cations parameter conditions min. typ. max. units mtbf mil hdbk 217f, 25oc, gnd benign 3.5 mhours safety standards ul 1950, en 60950, iec 60950 safety approvals ul, cul; file no. e245422 absolute maximum ratings parameter conditions min. typ. max. units input voltage surge (1 sec) 5 vdc input -0.7 9.0 vdc 12 vdc input -0.7 18.0 24 vdc input -0.7 30.0 lead temperature 1.5 mm from case for 10 sec 300 oc internal power dissipation all models 450 mw caution: exceeding absolute maximum ratings may damage the module. these are not continuous operating ratings. rohs compliant electrical speci? cations speci? cations typical @ +25c, nominal input voltage & rated output current, unless otherwise noted. speci? cations subject to change without notice.
model number input output load regulation (%, max) ef? ciency (%, typ) fuse rating slow-blow (ma) voltage (vdc) current (ma) voltage (vdc) current (ma, max) current (ma, min) nominal range full-load no-load g101e 5 4.5 - 5.5 278 30 5.0 200.0 20.0 15 72 500 g102e 5 4.5 - 5.5 270 30 9.0 111.0 12.0 15 74 500 g103e 5 4.5 - 5.5 260 30 12.0 83.0 9.0 15 77 500 g104e 5 4.5 - 5.5 253 30 15.0 67.0 7.0 15 79 500 g105e 5 4.5 - 5.5 278 30 5.0 100.0 10.0 15 72 500 g106e 5 4.5 - 5.5 267 30 9.0 56.0 6.0 15 75 500 g107e 5 4.5 - 5.5 256 30 12.0 42.0 5.0 15 78 500 g108e 5 4.5 - 5.5 253 30 15.0 33.0 4.0 15 79 500 g111e 12 10.8 - 13.2 114 15 5.0 200.0 20.0 15 73 200 g112e 12 10.8 - 13.2 111 15 9.0 111.0 12.0 15 75 200 g113e 12 10.8 - 13.2 105 15 12.0 83.0 9.0 15 79 200 g114e 12 10.8 - 13.2 104 15 15.0 67.0 7.0 15 80 200 g115e 12 10.8 - 13.2 113 15 5.0 100.0 10.0 15 74 200 g116e 12 10.8 - 13.2 110 15 9.0 56.0 6.0 15 76 200 g117e 12 10.8 - 13.2 105 15 12.0 42.0 5.0 15 79 200 g118e 12 10.8 - 13.2 104 15 15.0 33.0 4.0 15 80 200 g121e 24 21.6 - 26.4 56 8 5.0 200.0 20.0 15 74 100 g122e 24 21.6 - 26.4 55 8 9.0 111.0 12.0 15 76 100 g123e 24 21.6 - 26.4 52 8 12.0 83.0 9.0 15 80 100 g124e 24 21.6 - 26.4 51 8 15.0 67.0 7.0 15 81 100 g125e 24 21.6 - 26.4 56 8 5.0 100.0 10.0 15 74 100 g126e 24 21.6 - 26.4 55 8 9.0 56.0 6.0 15 76 100 g127e 24 21.6 - 26.4 52 8 12.0 42.0 5.0 15 80 100 g128e 24 21.6 - 26.4 51 8 15.0 33.0 4.0 15 81 100 derating curve model selection guide mechanical dimensions notes: ? all dimensions are typical in inches (mm) ? tolerance x.xx = 0.01 ( 0.25) ? pin 1 is marked by a dot or indentation on the top of the unit notes: 1. output load regulation is speci? ed for a load change of 10% to 100%. 2. these units should not be operated with a load under 10% of full load. operation at no-load may cause damage to the unit. 3. these converters will operate without external components. however, when measuring output ripple, it is recommended that an external ceramic capaci- tor be placed from the +vout pin to the -vout pin for single output units and from each out- put to common for dual output units. an input capacitor will enhance stability over tempera- ture and input line variations. recommended capacitor values are given in the table above. for applications requiring very low output noise levels, a simple lc ? lter should be effective. 4. dual output units may be connected to provide a 10v, 18v, 24v or 30 vdc output. to do this, connect the load across the positive (+vout) and negative (-vout) outputs and ? oat the output common 5. it is recommended that a fuse be used on the input of a power supply for protection. see the model selection table above for the correct rating. vin input capacitor vout output capacitor single dual 5 vdc 4.7 f 5 vdc 10.0 f 4.7 f 12 vdc 2.2 f 9 vdc 4.7 f 2.2 f 24 vdc 1.0 f 12 vdc 2.2 f 1.0 f 15 vdc 1.0 f 0.47 f other input/output combinations are available (i.e. 3.3 vdc). contact the factory for details at: sales@micropowerdirect.com pin single dual pin single dual 1 -vin -vin 9 +vout +vout 7 nc nc 11 -vout -vout 8 no pin common 14 +vin +vin nc = no connection pin connections micropower direct www.micropowerdirect.com 292 page street ste d stoughton, ma 02072 ? tel: (781) 344-8226 ? fax: (781) 344-8481 ? e-mail: sales@micropowerdirect.com
|
