quick start guide TWR-PXD10 32-bit power architecture ? mcu for entry-level industrial display solutions tower system
2 quick start guide get to know the TWR-PXD10 TWR-PXD10 freescale tower system the TWR-PXD10 module is part of the freescale tower system portfolio, a modular development platform that enables rapid prototyping and tool re-use through reconfigurable hardware. the TWR-PXD10 can be used with a broad selection of tower system peripheral modules, including the new twr-lcd-rgb which accepts rgb data from the pxd10 mcu graphics lcd controller. rgb leds general-purpose tower plug-in (twrpi) socket can rs485 secondary connector primary connector potentiometer push buttons nexus debug connector user leds jtag interface osjtag interface
3 tower system ? mpxd1010vlq64 mcu (e200 32-bit book e-compliant cpu core complex built on power architecture ? technology, 64 mhz, graphics lcd module, 160 kb on-chip graphics sram, up to 1 mb on-chip flash with flash controller) ? interfaces to the new twr-lcd-rgb tower peripheral module (accepts rgb data directly from the pxd10 mcu lcd controller) ? mc9s08jm60 open source jtag (osjtag) circuit ? spansion s25fl064p 64 mb qspi memory ? general-purpose twrpi socket (tower plug-in module) ? on-board can transceiver ? on-board rs485 half duplex transceiver ? two rgb leds for user interface ? two mechanical push buttons for user interface ? one potentiometer for adc testing TWR-PXD10 features
4 in this quick start guide, you will learn how to set up the TWR-PXD10 module and run the included demonstration software. for more detailed information, please see the user manual found on the included dvd or at freescale.com/TWR-PXD10 . quick start guide connect the TWR-PXD10 locate the secondary elevator in the assembled tower kit press the expansion connectors on the back of the twr-lcd-rgb module onto the matching side expansion port connectors found on the outer side of the secondary elevator. insert the TWR-PXD10 board into the primary and secondary elevator board. the primary and secondary cards for each module are indicated along the card edges. power up the TWR-PXD10 connect the TWR-PXD10 board to a computer or a wall charger using the provided usb cable. additionally, the usb connector on the primary elevator or osjtag connector can be used to power up the board. step-by-step installation instructions 1 2
5 tower system follow the on-screen menu press the swell software icon to start the animation. using the slider, you can modify the speed of the flying px series chips. by selecting the collision checkbox, the px logos will collide. 3 additional software and tools ? mqx? real-time os ? swell software peg graphical user interface ? green hills software multi ide ? serial bootloader utility ? codewarrior v10.x eclipse development studio ? osjtag virtual serial port using usb ? rapid application initialization and documentation tool (rappid) ? freemaster run-time debugging tool
6 quick start guide general jumper confguration jumper function j1 enable/disable potentiometer j2 enable/disable sw1 j3 enable/disable sw2 j4 enable/disable rgb led 2 j6 enable/disable rgb led 1 j9 enable/disable osjtag interface bootloader mode j12 enable/disable user led 2 j15 enable/disable user led 1 j23 enable/disable on-board can transceiver terminator resistor j25 enable/disable on-board rs485 half duplex transceiver terminator resistor uart confguration jumper position function j21 1-2 uart0 rx is connected to rs485 transceiver 2-3 uart0 rx is connected to uart0_rx on primary elevator j22 1-2 uart0 tx is connected to rs485 transceiver 2-3 uart0 tx is connected to uart0_tx on primary elevator TWR-PXD10 jumper options the following is a list of all jumper options. the default installed jumper settings are shown in white text within blue boxes. 5
7 tower system general jumper confguration jumper function j1 neise potentiometer j2 neise 1 j3 neise 2 j neise 2 j neise 1 j neise j interce ootoer moe j12 neise user 2 j15 neise user 1 j23 neise onor trnsceier termintor resistor j25 neise onor 5 upe trnsceier termintor resistor uart confguration jumper position function j21 12 is connecte to 5 trnsceier 23 is connecte to on primr eetor j22 12 is connecte to 5 trnsceier 23 is connecte to on primr eetor uart confguration (continued) jumper position function 1 12 1 is connecte to j 23 1 is connecte to 1 on primr eetor 1 12 1 is connecte to j 23 1 is connecte to 1 on primr eetor boot assistance module (bam) confguration jumper position function j1 12 f is connecte to use 23 f is connecte to use open p5 is use s p j11 12 is connecte to use 23 is connecte to use open p is use s p can confguration jumper position function j13 12 is connecte to onor trnsceier 23 is connecte to on primr eetor j1 12 is connecte to onor trnsceier 23 is connecte to on primr eetor
for more information, visit freescale.com/tower join the online tower community at towergeeks.org freescale, the freescale logo and codewarrior are trademarks of freescale semiconductor, inc., reg. u.s. pat. & tm. off. the power architecture and power.org word marks and the power and power.org logos and related marks are trademarks and service marks licensed by power.org. all other product or service names are the property of their respective owners. ? 2012 freescale semiconductor, inc. document number: twrpxd10qsg rev 0 agile number: 926-27279 rev a visit freescale.com/TWR-PXD10 for the latest information on the TWR-PXD10 module, including: ? board database: schematics, layout and bom ? user manual ? quick start guide ? software bsps and codewarrior development studio ? demos and tutorial ? fact sheet support visit freescale.com/support for a list of phone numbers within your region. warranty visit freescale.com/warranty for complete warranty information. quick start guide quick start guide
|
