? semiconductor components industries, llc, 2005 january, 2005 ? rev. 8 1 publication order number: mc74ac00/d mc74ac00, mc74act00 quad 2-input nand gate high?performance silicon?gate cmos features ? output drive capability: 24 ma ? operating voltage range: 2 to 6 v ac00; 4.5 to 5.5 act00 ? low input current: 1.0 a ? high noise immunity characteristic of cmos devices ? in compliance with the jedec standard no. 7a requirements ? chip complexity: 32 fets ? pb?free packages are available* 3 y1 1 a1 pin 14 = v cc pin 7 = gnd figure 1. logic diagram 2 b1 6 y2 4 a2 5 b2 8 y3 9 a3 10 b3 11 y4 12 a4 13 b4 y = ab figure 2. pinout: 14?lead packages (top view) 13 14 12 11 10 9 8 2 1 34567 v cc b4 a4 y4 b3 a3 y3 a1 b1 y1 a2 b2 y2 gnd *for additional information on our pb?free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d. marking diagrams xxx = ac or act a = assembly location wl or l = wafer lot yy or y = year ww or w = work week tssop?14 dt suffix case 948g xxx 00 alyw 1 14 1 14 pdip?14 n suffix case 646 mc74xxx00n awlyyww soic?14 d suffix case 751a 1 14 xxx00 awlyww soeiaj?14 m suffix case 965 1 14 74xxx00 alyw 1 14 1 14 1 14 1 14 see detailed ordering and shipping information in the package dimensions section on page 5 of this data sheet. ordering information l l h h l h l h function table inputs output ab h h h l y http://onsemi.com
mc74ac00, mc74act00 http://onsemi.com 2 maximum ratings symbol parameter value unit v cc dc supply voltage 0.5 to 7.0 v v i dc input voltage 0.5 v i v cc 0.5 v v o dc output voltage (note 1) 0.5 v o v cc 0.5 v i ik dc input diode current 20 ma i ok dc output diode current 50 ma i o dc output sink/source current 50 ma i cc dc supply current per output pin 50 ma i gnd dc ground current per output pin 50 ma t stg storage temperature range 65 to 150 c t l lead temperature, 1 mm from case for 10 seconds 260 c t j junction temperature under bias 150 c ja thermal resistance pdip soic tssop 78 125 170 c/w p d power dissipation in still air at 85 c pdip soic tssop 78 125 170 mw msl moisture sensitivity level 1 f r flammability rating oxygen index: 30% ? 35% ul 94 v?0 @ 0.125 in v esd esd withstand voltage human body model (note 2) machine model (note 3) charged device model (note 4) > 2000 > 200 > 1000 v i latch?up latch?up performance above v cc and below gnd at 85 c (note 5) 100 ma maximum ratings are those values beyond which device damage can occur. maximum ratings applied to the device are individual str ess limit values (not normal operating conditions) and are not valid simultaneously. if these limits are exceeded, device functional operation i s not implied, damage may occur and reliability may be affected. 1. i o absolute maximum rating must be observed. 2. tested to eia/jesd22?a114?a. 3. tested to eia/jesd22?a115?a. 4. tested to jesd22?c101?a. 5. tested to eia/jesd78. recommended operating conditions symbol parameter min typ max unit v cc supply voltage mc74ac00 mc74act00 2.0 4.5 5.0 5.0 6.0 5.5 v v in , v out dc input voltage, output voltage (ref. to gnd) 0 ? v cc v t r , t f input rise and fall time (note 6) v cc @ 3.0 v mc74ac00 v cc @ 4.5 v v cc @ 5.5 v ? ? ? 150 40 25 ? ? ? ns/v t r , t f input rise and fall time (note 7) v cc @ 4.5 v mc74act00 v cc @ 5.5 v ? ? 10 8.0 ? ? ns/v t j junction temperature ? ? 150 c t a operating ambient temperature range ?55 25 125 c i oh output current ? high ? ? ?24 ma i ol output current ? low ? ? 24 ma 6. v in from 30% to 70% v cc . 7. v in from 0.8 v to 2.0 v.
mc74ac00, mc74act00 http://onsemi.com 3 dc characteristics mc74ac00 v cc t a = +25 c t a = ?40 c to +85 c t a = ?55 c + 125 c symbol parameter v cc (v) typ guaranteed limits unit conditions v ih minimum high level input voltage 3.0 4.5 5.5 1.5 2.25 2.75 2.1 3.15 3.85 2.1 3.15 3.85 2.1 3.15 3.85 v v out = 0.1 v or v cc ? 0.1 v v il maximum low level input voltage 3.0 4.5 5.5 1.5 2.25 2.75 0.9 1.35 1.65 0.9 1.35 1.65 0.9 1.35 1.65 v v out = 0.1 v or v cc ? 0.1 v v oh minimum high level output voltage 3.0 4.5 5.5 2.99 4.49 5.49 2.9 4.4 5.4 2.9 4.4 5.4 2.9 4.4 5.4 v i out = ?50 a 3.0 4.5 5.5 ? ? ? 2.56 3.86 4.86 2.46 3.76 4.76 2.4 3.7 4.7 v *v in = v il or v ih ?12 ma i oh ?24 ma ?24 ma v ol maximum low level output voltage 3.0 4.5 5.5 0.002 0.001 0.001 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 v i out = 50 a 3.0 4.5 5.5 ? ? ? 0.36 0.36 0.36 0.44 0.44 0.44 0.5 0.5 0.5 v *v in = v il or v ih 12 ma i ol 24 ma 24 ma i in maximum input leakage current 5.5 ? 0. 1 1.0 1.0 a v i = v cc , gnd i old 2minimum dynamic out p ut current 5.5 ? ? 75 50 ma v old = 1.65 v max i ohd output current 5.5 ? ? ?75 ?50 ma v ohd = 3.85 v min i cc maximum quiescent supply current 5.5 ? 4.0 40 40 a v in = v cc or gnd *all outputs loaded; thresholds on input associated with output under test. 2maximum test duration 2.0 ms, one output loaded at a time. note: i in and i cc @ 3.0 v are guaranteed to be less than or equal to the respective limit @ 5.5 v v cc . ac characteristics (t r = t f = 3.0 ns; c l = 50 pf; see figures 3 and 4 for waveforms) mc74ac00 v cc * t a = +25 c t a = ?40 c to +85 c t a = ?55 c to + 125 c symbol parameter v cc * (v) min typ max min max min max unit t plh propagation delay 3.3 5.0 2.0 1.5 7.0 6.0 9.5 8.0 2.0 1.5 10.0 8.5 1.0 1.0 11.0 8.5 ns t phl propagation delay 3.3 5.0 1.5 1.5 5.5 4.5 8.0 6.5 1.0 1.0 8.5 7.0 1.0 1.0 9.0 7.0 ns *voltage range 3.3 v is 3.3 v 0.3 v. voltage range 5.0 v is 5.0 v 0.5 v.
mc74ac00, mc74act00 http://onsemi.com 4 dc characteristics mc74act00 v cc t a = +25 c t a = ?40 c to +85 c t a = ?55 c to + 125 c symbol parameter v cc (v) typ guaranteed limits unit conditions v ih minimum high level input voltage 4.5 5.5 1.5 1.5 2.0 2.0 2.0 2.0 2.0 2.0 v v out = 0.1 v or v cc ? 0.1 v v il maximum low level input voltage 4.5 5.5 1.5 1.5 0.8 0.8 0.8 0.8 0.8 0.8 v v out = 0.1 v or v cc ? 0.1 v v oh minimum high level output voltage 4.5 5.5 4.49 5.49 4.4 5.4 4.4 5.4 4.4 5.4 v i out = ?50 a 4.5 5.5 ? ? 3.86 4.86 3.76 4.76 3.7 4.7 v *v in = v il or v ih i oh ?24 ma ?24 ma v ol maximum low level output voltage 4.5 5.5 0.001 0.001 0.1 0.1 0.1 0.1 0.1 0.1 v i out = 50 a 4.5 5.5 ? ? 0.36 0.36 0.44 0.44 0.5 0.5 v *v in = v il or v ih i ol 24 ma 24 ma i in maximum input leakage current 5.5 ? 0.1 1.0 1.0 a v i = v cc , gnd i cct additional max. i cc /input 5.5 0.6 ? 1.5 1.6 ma v i = v cc ? 2.1 v i old 2minimum dynamic out p ut current 5.5 ? ? 75 50 ma v old = 1.65 v max i ohd output current 5.5 ? ? ?75 ?50 ma v ohd = 3.85 v min i cc maximum quiescent supply current 5.5 ? 4.0 40 40 a v in = v cc or gnd *all outputs loaded; thresholds on input associated with output under test. 2maximum test duration 2.0 ms, one output loaded at a time. ac characteristics (t r = t f = 3.0 ns; c l = 50 pf; see figures 3 and 4 for waveforms) mc74act00 v cc * t a = +25 c t a = ?40 c to +85 c t a = ?55 c to +125 c symbol parameter v cc * (v) min typ max min max min max unit t plh propagation delay 5.0 1.5 5.5 9.0 1.0 9.5 1.0 9.5 ns t phl propagation delay 5.0 1.5 4.0 7.0 1.0 8.0 1.0 8.0 ns *voltage range 5.0 v is 5.0 v 0.5 v. capacitance symbol parameter value typ test conditions unit c in input capacitance 4.5 v cc = 5.0 v pf c pd power dissipation capacitance 30 v cc = 5.0 v pf
mc74ac00, mc74act00 http://onsemi.com 5 figure 3. switching waveforms gnd v cc output y input a or b c l * *includes all probe and jig capacitance 50% device under test output figure 4. test circuit 90% v mi 10% t plh t phl t f t r 50 scope test point 450 input v mi = 50% for mc74ac00 = 1.5 v for mc74act00 order information device package shipping 2 mc74ac00d soic?14 55 units / rail mc74ac00dg soic?14 (pb?free) 55 units / rail mc74ac00n pdip?14 500 / tape & reel mc74ac00ng pdip?14 (pb?free) 500 / tape & reel MC74AC00DR2 soic?14 2500 / tape and reel MC74AC00DR2g soic?14 (pb?free) 2500 / tape and reel mc74ac00dtr2 tssop?14* 2500 / tape and reel mc74ac00mel soeiaj?14 2000 tape and reel mc74act00n pdip?14 2000 units / box mc74act00d soic?14 55 units / rail mc74act00dr2 soic?14 2500 / tape and reel mc74act00dtr2 tssop?14* 2500 / tape and reel mc74act00mel soeiaj?14 2000 / tape and reel 2for information on tape and reel specifications, including part orientation and tape sizes, please refer to our tape and reel packaging specifications brochure, brd8011/d. *this package is inherently pb?free.
mc74ac00, mc74act00 http://onsemi.com 6 package dimensions notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: millimeter. 3. dimensions a and b do not include mold protrusion. 4. maximum mold protrusion 0.15 (0.006) per side. 5. dimension d does not include dambar protrusion. allowable dambar protrusion shall be 0.127 (0.005) total in excess of the d dimension at maximum material condition. ?a? ?b? g p 7 pl 14 8 7 1 m 0.25 (0.010) b m s b m 0.25 (0.010) a s t ?t? f r x 45 seating plane d 14 pl k c j m dim min max min max inches millimeters a 8.55 8.75 0.337 0.344 b 3.80 4.00 0.150 0.157 c 1.35 1.75 0.054 0.068 d 0.35 0.49 0.014 0.019 f 0.40 1.25 0.016 0.049 g 1.27 bsc 0.050 bsc j 0.19 0.25 0.008 0.009 k 0.10 0.25 0.004 0.009 m 0 7 0 7 p 5.80 6.20 0.228 0.244 r 0.25 0.50 0.010 0.019 pdip?14 n suffix case 646?06 issue n soic?14 d suffix case 751a?03 issue g 17 14 8 b a dim min max min max millimeters inches a 0.715 0.770 18.16 18.80 b 0.240 0.260 6.10 6.60 c 0.145 0.185 3.69 4.69 d 0.015 0.021 0.38 0.53 f 0.040 0.070 1.02 1.78 g 0.100 bsc 2.54 bsc h 0.052 0.095 1.32 2.41 j 0.008 0.015 0.20 0.38 k 0.115 0.135 2.92 3.43 l m ??? 10 ??? 10 n 0.015 0.039 0.38 1.01 notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: inch. 3. dimension l to center of leads when formed parallel. 4. dimension b does not include mold flash. 5. rounded corners optional. f hg d k c seating plane n ?t? 14 pl m 0.13 (0.005) l m j 0.290 0.310 7.37 7.87
mc74ac00, mc74act00 http://onsemi.com 7 package dimensions tssop?14 dt suffix case 948g?01 issue o dim min max min max inches millimeters a 4.90 5.10 0.193 0.200 b 4.30 4.50 0.169 0.177 c --- 1.20 --- 0.047 d 0.05 0.15 0.002 0.006 f 0.50 0.75 0.020 0.030 g 0.65 bsc 0.026 bsc h 0.50 0.60 0.020 0.024 j 0.09 0.20 0.004 0.008 j1 0.09 0.16 0.004 0.006 k 0.19 0.30 0.007 0.012 k1 0.19 0.25 0.007 0.010 l 6.40 bsc 0.252 bsc m 0 8 0 8 notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: millimeter. 3. dimension a does not include mold flash, protrusions or gate burrs. mold flash or gate burrs shall not exceed 0.15 (0.006) per side. 4. dimension b does not include interlead flash or protrusion. interlead flash or protrusion shall not exceed 0.25 (0.010) per side. 5. dimension k does not include dambar protrusion. allowable dambar protrusion shall be 0.08 (0.003) total in excess of the k dimension at maximum material condition. 6. terminal numbers are shown for reference only. 7. dimension a and b are to be determined at datum plane -w-. s u 0.15 (0.006) t 2x l/2 s u m 0.10 (0.004) v s t l ?u? seating plane 0.10 (0.004) ?t? ?? ?? section n-n detail e j j1 k k1 detail e f m -w- 0.25 (0.010) 8 14 7 1 pin 1 ident. h g a d c b s u 0.15 (0.006) t ?v? 14x ref k n n h e a 1 dim min max min max inches --- 2.05 --- 0.081 millimeters 0.05 0.20 0.002 0.008 0.35 0.50 0.014 0.020 0.18 0.27 0.007 0.011 9.90 10.50 0.390 0.413 5.10 5.45 0.201 0.215 1.27 bsc 0.050 bsc 7.40 8.20 0.291 0.323 0.50 0.85 0.020 0.033 1.10 1.50 0.043 0.059 0 0.70 0.90 0.028 0.035 --- 1.42 --- 0.056 a 1 h e q 1 l e 10 0 10 l e q 1 notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: millimeter. 3. dimensions d and e do not include mold flash or protrusions and are measured at the parting line. mold flash or protrusions shall not exceed 0.15 (0.006) per side. 4. terminal numbers are shown for reference only. 5. the lead width dimension (b) does not include dambar protrusion. allowable dambar protrusion shall be 0.08 (0.003) total in excess of the lead width dimension at maximum material condition. dambar cannot be located on the lower radius or the foot. minimum space between protrusions and adjacent lead to be 0.46 ( 0.018). 0.13 (0.005) m 0.10 (0.004) d z e 1 14 8 7 e a b view p c l detail p m a b c d e e 0.50 m z soeiaj?14 tbd suffix case 965?01 issue o
mc74ac00, mc74act00 http://onsemi.com 8 on semiconductor and are registered trademarks of semiconductor components industries, llc (scillc). scillc reserves the right to mak e changes without further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for an y particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including wi thout limitation special, consequential or incidental damages. atypicalo parameters which may be provided in scillc data sheets and/or specifications can and do vary in different application s and actual performance may vary over time. all operating parameters, including atypicalso must be validated for each customer application by customer's technical experts. scillc does not convey any license under its patent rights nor the rights of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the scillc product could create a sit uation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer shall indemnify and hold scillc and its officers, employees, subsidiaries, af filiates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, direct ly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that scillc was negligent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyright laws and is not for resale in any manner. publication ordering information n. american technical support : 800?282?9855 toll free usa/canada japan : on semiconductor, japan customer focus center 2?9?1 kamimeguro, meguro?ku, tokyo, japan 153?0051 phone : 81?3?5773?3850 mc74ac00/d literature fulfillment : literature distribution center for on semiconductor p.o. box 61312, phoenix, arizona 85082?1312 usa phone : 480?829?7710 or 800?344?3860 toll free usa/canada fax : 480?829?7709 or 800?344?3867 toll free usa/canada email : orderlit@onsemi.com on semiconductor website : http://onsemi.com order literature : http://www.onsemi.com/litorder for additional information, please contact your local sales representative.
|
