View SXX10D_5077757.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

241 ?2010 littelfuse, inc revised: july 29, 2010 09:54 am teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. sxx10xsx & sxx10x series 10 amp sensitive & standard scrs 10a scrs sxx10xsx & sxx10x series description excellent unidirectional switches for phase control and general switching applications such as heating and motor speed controls. sensitive gate scrs are easily triggered with microamps of current as furnished by sense coils, proximity switches, and microprocessors. standard phase control scrs are triggered with few milliamperes of current at less than 1.5v potential. features & bene?ts t 3p)4dpnqmjbou t (mbttoqbttjwbufe junctions t 7pmubhfdbqbcjmjuzvq to 1000 v t 4vshfdbqbcjmjuzvq to 100 a main features symbol value unit i t(rms) 10 a v drm /v rrm 400 to 1000 v i (5 0.2 to 15 ma schematic symbol agency approval agency agency file number ? to-220l package : e71639 applications typical applications are capacitive discharge systems for strobe lights, nailers, staplers and gas engine ignition. also controls for power tools, home/brown goods and white goods appliances. internally constructed isolated packages are offered for ease of heat sinking with highest isolation voltage. a k g ?
242 revised: july 29, 2010 09:54 am ?2010 littelfuse, inc teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. 10 amp sensitive & standard scrs sxx10xsx & sxx10x series absolute maximum ratings standard scrs symbol parameter test conditions value unit i t(rms) rms on-state current sxx10l t c = 95c 10 a sxx10r SXX10D sxx10v t c = 105c i t(av) average on-state current sxx10l t c = 95c 6.4 a sxx10r SXX10D sxx10v t c = 105c i tsm peak non-repetitive surge current tjohmfibmgdzdmfg)[ t j (initial) = 25c 83 a tjohmfibmgdzdmfg)[ t j (initial) = 25c 100 i 2 t i 2 t value for fusing t p = 8.3 ms 41 a 2 s di/dt critical rate-of-rise of on-state current g)[5 j = 125c 100 a/s i (. peak gate current t j = 125c 2a p ( "7
average gate power dissipation t j = 125c 0.5 w t stg storage temperature range -40 to 150 c t j operating junction temperature range -40 to 125 c note: xx = voltage absolute maximum ratings sensitive scrs symbol parameter test conditions value unit i t(rms) rms on-state current sxx10lsy t c = 80c 10 a sxx10rsy SXX10Dsy sxx10vsy t c = 95c i t(av) average on-state current sxx10lsy t c = 80c 6.4 a sxx10rsy SXX10Dsy sxx10vsy t c = 95c i tsm peak non-repetitive surge current tjohmfibmgdzdmfg)[ t j (initial) = 25c 83 a tjohmfibmgdzdmfg)[ t j (initial) = 25c 100 i 2 ti 2 t value for fusing t p = 8.3 ms 41 a 2 s di/dt critical rate of rise of on-state current g)[5 j = 110c 100 a/s i (. peak gate current t j = 110c 1a p ( "7
average gate power dissipation t j = 110c 0.1 w t stg storage temperature range -40 to 150 c t j operating junction temperature range -40 to 110 c note: xx = voltage, y = sensitivity
243 ?2010 littelfuse, inc revised: july 29, 2010 09:54 am teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. sxx10xsx & sxx10x series 10 amp sensitive & standard scrs 10a scrs electrical characteristics (t j = 25c, unless otherwise speci?ed) C sensitive scrs symbol test conditions value unit sxx10xs2 sxx10xs3 i (5 v d = 6v r l = 100 8 max. 200 500 a v (5 max. 0.8 v dv/dt v d = v drm ; r (, = 1k 8 ; t j = 110c typ. 8 v/s v (% v d = v drm ; r l = 3.3 k 8 ; t j = 110c min. 0.2 v v (3. i (3 = 10a min. 6 v i ) i t = 20ma (initial) max. 6 8 ma t q (1) max. 50 45 s t gt i ( = 2 x i (5 ; pw = 15s; i t = 12a typ. 4 5 s note: xx = voltage, x = package (1) i t =2a; t p =50s; dv/dt=5v/s; di/dt=-30a/s symbol test conditions value unit sxx10x i (5 v d = 12v r l = 60 8 max. 15 ma v (5 max. 1.5 v dv/dt v d = v drm ; gate open; t j = 100c 400v min. 350 v/s 600v 300 800v 250 1000v 100 v d = v drm ; gate open; t j = 125c 400v 250 600v 225 800v 200 v (% v d = v drm ; r l = 3.3 k 8 ; t j = 125c min. 0.2 v i ) i t = 200ma (initial) max. 30 ma t q (1) max. 35 s t gt i ( = 2 x i (5 ; pw = 15s; i t = 20a typ. 2 s note: xx = voltage, x = package (1) i t =2a; t p =50s; dv/dt=5v/s; di/dt=-30a/s electrical characteristics (t j = 25c, unless otherwise speci?ed) C standard scrs static characteristics symbol test conditions value unit v tm i t = 20a; t p = 380 s max. 1.6 v i drm / i rrm v drm / v rrm sxx10xyy t j = 25c 400 - 600v max. 5 a t j = 110c 400 - 600v 250 sxx10x t j = 25c 400 - 800v 10 1000v 20 t j = 100c 400 - 800v 200 1000v 3000 t j = 125c 400 - 800v 500 note: xx = voltage, x = package, yy = sensitivity
244 revised: july 29, 2010 09:54 am ?2010 littelfuse, inc teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. 10 amp sensitive & standard scrs sxx10xsx & sxx10x series thermal resistances symbol parameter value unit r r (j-c) junction to case (ac) sxx10rsy 1.6 c/w sxx10lsy 3.0 sxx10vsy 1.7 SXX10Dsy 1.45 sxx10r 1.6 sxx10l 3.0 sxx10v 1.7 SXX10D 1.45 r r (j-a) junction to ambient sxx10rsy 40 c/w sxx10lsy 65 sxx10vsy 85 sxx10r 40 sxx10l 50 sxx10v 70 note: xx = voltage, y = sensitivity figure 1: normalized dc gate trigger current vs. junction temperature (sensitive scr) figure 2: normalized dc gate trigger current vs. junction temperature (standard scr) 0.0 1.0 2.0 3.0 4.0 -40 -15 10 35 60 85 110 junction temperature (t j ) -- (c) ratio of i gt / i gt (t j = 2 5 c) 125 0.0 1.0 2.0 3.0 4.0 -40 -15 10 35 60 85 110 junction temperature (t j ) -- (c) ratio of i gt / i gt (t j = 2 5 c)
245 ?2010 littelfuse, inc revised: july 29, 2010 09:54 am teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. sxx10xsx & sxx10x series 10 amp sensitive & standard scrs 10a scrs 125 0.0 0.5 1.0 1.5 2.0 -40 -15 10 35 60 85 110 junction temperature (t j ) -- (c) ratio of i h / i h (t j = 2 5 c) 125 0.0 0.5 1. 0 1. 5 2.0 -40 -15 10 35 60 85 110 junction temperature (t j ) -- (c) ratio of v gt / v gt (t j = 2 5 c) 0 4 8 12 16 20 24 28 32 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 instantaneous on-state current (i t ) C amps instantaneous on-state voltage (v t ) C volts t j = 2 5 oc 0 1 2 3 4 5 6 7 8 9 10 012345678910 rms on-state current [i t(rms) ] -- (amps) average on-state power dissipation [p d(av) ] -- (watts) figure 5: on-state current vs. on-state voltage (typical) figure 6: power dissipation (typical) vs. rms on-state current figure 3: normalized dc gate trigger voltage vs. junction temperature figure 4: normalized dc holding current vs. junction temperature figure 7: maximum allowable case temperature vs. rms on-state current figure 8: maximum allowable case temperature vs. average on-state current 70 75 80 85 90 95 100 105 110 11 5 120 125 130 01234567891011 rms on-state current [i t(rms) ] - amps sxx10rsy SXX10Dsy sxx10vsy sxx10l sxx10lsy sxx10r SXX10D sxx10v current waveform: sinusoidal load: resistive or inductive conduction angle: 180 free air rating maximum allowable case temperature (t c ) - c 70 75 80 85 90 95 100 105 110 11 5 120 125 130 01234567 sxx10lsy sxx10rsy SXX10Dsy sxx10vsy sxx10r SXX10D sxx10v current waveform: sinusoidal load: resistive or inductive conduction angle: 180 free air rating maximum allowable case temperature (t c ) - c average on-state current [i t(ave) ] - amps sxx10l
246 revised: july 29, 2010 09:54 am ?2010 littelfuse, inc teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. 10 amp sensitive & standard scrs sxx10xsx & sxx10x series figure 11: peak capacitor discharge current figure 12: peak capacitor discharge current derating figure 9: maximum allowable ambient temperature vs. rms on-state current figure 10: maximum allowable ambient temperature vs. average on-state current note: xx = voltage, y = sensitivity 0 20 40 60 80 100 120 0.0 0.5 1.0 1.5 average on-state current [i t(ave) ] - amps maximum allowable ambient temperature (t a ) - c sxx10rsy sxx10lsy sxx10vsy sxx10r sxx10l sxx10v current waveform: sinusoidal load: resistive or inductive conduction angle: 180 free air rating 0.0 0.2 0.4 0.6 0.8 1. 0 1. 2 0255075100125150 normalized peak current sensitive scr case temperature (t c ) - c standard scr 10 100 1000 0.5 1.0 10.0 50.0 pulse current duration (t w ) - ms peak discharge current (i tm ) - amps i trm t w 0 20 40 60 80 100 120 0.0 0.5 1.0 1.5 2.0 2.5 average on-state current [i t(ave) ] - amps current waveform: sinusoidal load: resistive or inductive conduction angle: 180 free air rating sxx10r sxx10l sxx10v sxx10rsy sxx10lsy sxx10vsy maximum allowable case temperature (t c ) - c 1 10 100 1000 1 10 100 1000 peak surge (non-repetitive) on-state current (i tsm ) C amps surge current duration -- full cycles figure 13: surge peak on-state current vs. number of cycles 4611-:'3&26&/$:)[4jovtpjebm load: resistive rms on-state current: [i t(rms) ]: maximum rated value at speci?ed case temperature notes: (bufdpouspmnbzcfmptuevsjohboejnnfejbufmz following surge current interval. 2. overload may not be repeated until junction temperature has returned to steady-state rated value.
247 ?2010 littelfuse, inc revised: july 29, 2010 09:54 am teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. sxx10xsx & sxx10x series 10 amp sensitive & standard scrs 10a scrs soldering parameters re?ow condition 1co'sffbttfncmz pre heat - temperature min (t s(min) ) 150c - temperature max (t s(max) ) 200c - time (min to max) (t s ) otfdt average ramp up rate (liquidus temp) (t l ) to peak 5c/second max t s(max) to t l - ramp-up rate 5c/second max re?ow - temperature (t l ) (liquidus) 217c - temperature (t l ) otfdpoet peak temperature (t p ) 260 +0/-5 c time within 5 c of actual peak temperature (t p ) otfdpoet ramp-down rate 5c/second max time 2 5 c to peak temperature (t p ) 8 minutes max. do not exceed 280c time temperature t p t l t s(max) t s(min) 25 t p t l t s time to peak temperature preheat p reheat ramp-up ramp-up ramp-down r am p - do physical speci?cations environmental speci?cations test speci?cations and conditions ac blocking mil-std-750, m-1040, cond a applied peak ac voltage @ 125c for 1008 hours temperature cycling mil-std-750, m-1051, 100 cycles; -40c to +150c; 15-min dwell-time temperature/ humidity eia / jedec, jesd22-a101 1008 hours; 320v - dc: 85c; 85% rel humidity high temp storage mil-std-750, m-1031, 1008 hours; 150c low-temp storage 1008 hours; -40c thermal shock mil-std-750, m-1056 10 cycles; 0c to 100c; 5-min dwell- time at each temperature; 10 sec (max) transfer time between temperature autoclave eia / jedec, jesd22-a102 168 hours (121c at 2 atms) and 3) resistance to solder heat mil-std-750 method 2031 solderability ansi/j-std-002, category 3, test a lead bend mil-std-750, m-2036 cond e terminal finish 100% matte tin-plated body material 6-sfdphoj[fefqpyznffujohnbnnbcjmjuz classi?cation 94v-0 lead material copper alloy design considerations careful selection of the correct device for the applications operating parameters and environment will go a long way upxbsefyufoejohuifpqfsbujohmjgfpguif5izsjtups(ppe design practice should limit the maximum continuous current through the main terminals to 75% of the device rating. other ways to ensure long life for a power discrete semiconductor are proper heat sinking and selection of voltage ratings for worst case conditions. overheating, overvoltage (including dv/dt), and surge currents are the main killers of semiconductors. correct mounting, soldering, and forming of the leads also help protect against component damage.
248 revised: july 29, 2010 09:54 am ?2010 littelfuse, inc teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. 10 amp sensitive & standard scrs sxx10xsx & sxx10x series product selector part number voltage gate sensitivity type package 400v 600v 800v 1000v sxx10rs2 x x 0.2ma sensitive scr to-220r sxx10ls2 x x 0.2ma sensitive scr to-220l sxx10vs2 x x 0.2ma sensitive scr to-251 SXX10Ds2 x x 0.2ma sensitive scr to-252 sxx10rs3 x x 0.5ma sensitive scr to-220r sxx10ls3 x x 0.5ma sensitive scr to-220l sxx10vs3 x x 0.5ma sensitive scr to-251 SXX10Ds3 x x 0.5ma sensitive scr to-252 sxx10r xxxx 15ma st andard scr to-220r sxx10l xxxx 15ma st andard scr to-220l sxx10v xxxx 15ma st andard scr to-251 SXX10D xxxx 15ma st andard scr to-252 note: xx = voltage dimensions to-251aa (v/i-package) v/i-pak through hole dimension inches millimeters min typ max min typ max a 0.040 0.044 0.050 1.02 1.11 1.27 b 0.235 0.242 0.245 5.97 6.15 6.22 c 0.350 0.361 0.375 8.89 9.18 9.53 d 0.205 0.208 0.213 5.21 5.29 5.41 e 0.255 0.262 0.265 6.48 6.66 6.73 f 0.027 0.031 0.033 0.69 0.80 0.84 ( 0.087 0.090 0.093 2.21 2.28 2.36 ) 0.085 0.092 0.095 2.16 2.34 2.41 i 0.176 0.180 0.184 4.47 4.57 4.67 j 0.018 0.020 0.023 0.46 0.51 0.58 , 0.038 0.040 0.044 0.97 1.01 1.12 l 0.018 0.020 0.023 0.46 0.52 0.58 p 0.042 0.047 0.052 1.06 1.20 1.32 q 0.034 0.039 0.044 0.86 1.00 1.11 r 0.034 0.039 0.044 0.86 1.00 1.11 s 0.074 0.079 0.084 1.86 2.00 2.11 area: 0.040 in 2 t c measuring point gate g i e d a b c f j h k l 5.28 .208 5.34 .210 anode cathode anode p q r s
249 ?2010 littelfuse, inc revised: july 29, 2010 09:54 am teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. sxx10xsx & sxx10x series 10 amp sensitive & standard scrs 10a scrs dimensions to-252aa (d-package) d-pak surface mount dimension inches millimeters min typ max min typ max a 0.040 0.043 0.050 1.02 1.09 1.27 b 0.235 0.243 0.245 5.97 6.16 6.22 c 0.106 0.108 0.113 2.69 2.74 2.87 d 0.205 0.208 0.213 5.21 5.29 5.41 e 0.255 0.262 0.265 6.48 6.65 6.73 f 0.027 0.031 0.033 0.69 0.80 0.84 ( 0.087 0.090 0.093 2.21 2.28 2.36 ) 0.085 0.092 0.095 2.16 2.33 2.41 i 0.176 0.179 0.184 4.47 4.55 4.67 j 0.018 0.020 0.023 0.46 0.51 0.58 , 0.038 0.040 0.044 0.97 1.02 1.12 l 0.018 0.020 0.023 0.46 0.51 0.58 m 0.000 0.000 0.004 0.00 0.00 0.10 n 0.021 0.026 0.027 0.53 0.67 0.69 o 005005 p 0.042 0.047 0.052 1.06 1.20 1.32 q 0.034 0.039 0.044 0.86 1.00 1.11 m o n h j l k .118 3 .063 1.60 .071 1.80 .264 6.71 .264 6.71 .181 4.60 gate anode cathode anode t c measuring point g i d e a b c f 5.28 .208 5.34 .210 : 0.040 in 2 area p q
250 revised: july 29, 2010 09:54 am ?2010 littelfuse, inc teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. 10 amp sensitive & standard scrs sxx10xsx & sxx10x series dimensions to-220ab (r-package) non-isolated mounting tab common with center lead dimension inches millimeters min max min max a 0.380 0.420 9.65 10.67 b 0.105 0.115 2.67 2.92 c 0.230 0.250 5.84 6.35 d 0.590 0.620 14.99 15.75 e 0.142 0.147 3.61 3.73 f 0.110 0.130 2.79 3.30 ( 0.540 0.575 13.72 14.61 ) 0.025 0.035 0.64 0.89 j 0.195 0.205 4.95 5.21 , 0.095 0.105 2.41 2.67 l 0.060 0.075 1.52 1.91 m 0.085 0.095 2.16 2.41 n 0.018 0.024 0.46 0.61 o 0.178 0.188 4.52 4.78 p 0.045 0.060 1.14 1.52 r 0.038 0.048 0.97 1.22 k j a h g b f e c d l r t c measuring point anode o p n m .276 7. 0 1 .526 13.36 .320 8.13 area (ref.) 0.17 in 2 notch in gate lead to id. non-isolated tab gate cathode anode dimensions to-220ab (l-package) isolated mounting tab dimension inches millimeters min max min max a 0.380 0.420 9.65 10.67 b 0.105 0.115 2.67 2.92 c 0.230 0.250 5.84 6.35 d 0.590 0.620 14.99 15.75 e 0.142 0.147 3.61 3.73 f 0.110 0.130 2.79 3.30 ( 0.540 0.575 13.72 14.61 ) 0.025 0.035 0.64 0.89 j 0.195 0.205 4.95 5.21 , 0.095 0.105 2.41 2.67 l 0.060 0.075 1.52 1.91 m 0.085 0.095 2.16 2.41 n 0.018 0.024 0.46 0.61 o 0.178 0.188 4.52 4.78 p 0.045 0.060 1.14 1.52 r 0.038 0.048 0.97 1.22 a h g b f e c d l r t c measuring point area (ref.) 0.17 in 2 o p n m .320 8.13 .526 13.36 .276 7. 0 1 k j gate cathode anode note: maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 nm). note: maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 nm).
251 ?2010 littelfuse, inc revised: july 29, 2010 09:54 am teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. sxx10xsx & sxx10x series 10 amp sensitive & standard scrs 10a scrs packing options part number marking weight packing mode base quantity sxx10l/ryy sxx10l/ryy 2.2 g bulk 500 sxx10l/ryytp sxx10l/ryy 2.2 g tube 500 (50 per tube) SXX10Dyytp SXX10Dyy 0.3 g tube 750 (75 per tube) SXX10Dyyrp SXX10Dyy 0.3 g embossed carrier 2500 sxx10vyytp sxx10vyy 0.4 g tube 750 (75 per tube) sxx10l/r sxx10l/r 2.2 g bulk 500 sxx10l/rtp sxx10l/r 2.2 g tube 500 (50 per tube) SXX10Dtp SXX10D 0.3 g tube 750 (75 per tube) SXX10Drp SXX10D 0.3 g embossed carrier 2500 sxx10vtp sxx10v 0.4 g tube 750 (75 per tube) note: xx = voltage; yy = sensitivity 0.512 (13.0) arbor hole dia. dc xxxxxx xxxxxx dc xxxxxx dc xxxxxx xx xx xx gate cathode anode 0.63 (16.0) 0.157 (4.0) 0.64 (16.3) 12.99 (330.0) 0.524 (13.3) 0.315 (8.0) 0.059 dia (1.5) * * cover tape direction of feed dimensions are in inches (and millimeters). to-252 embossed carrier reel pack (rp) speci?cations meets all eia-481-2 standards part numbering system part marking system current 10: 10a sensitivity & type sensitive scr: s2: 200a standard scr: (blank): 15ma package type l : to-220 isolated r : to-220 non-isolated v : to-251 (vpak) d : to-252 (dpak) voltage rating 40 : 400v 60 : 600v 80 : 800v k0 : 1000v lead form dimensions xx : lead form option s 60 10 l s2 56 device type s : scr s3: 500a SXX10Ds3 yxxxx to-2 5 2aa C (d package ) to-2 5 1aa C (v package) sxx10l to-220ab - (r & l packages) yxxxx ? ?

▲Up To Search▲

Price & Availability of SXX10D

	To Download SXX10D Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .