manufacturer category series package voltage class rev . date ecliptek corp. oscillator e13c7 ceramic 3.3v os1m 01/09 e13c7 series oscillator e13c7 electrical specifications 800-ecliptek www.ecliptek.com for latest revision specifications subject to change without notice. ? rohs compliant (pb-free) ? lvpecl output oscillators ? 3.3v supply voltage ? ceramic 6-pad smd package ? stability to 20ppm ? tri-state output ? complementary output ? available on tape and reel ? wide range of available frequencies 0c to 70c, or -40c to +85c -55c to 125c 3.3v dc 5% 75ma maximum 100ma maximum 100ppm, 50ppm, 25ppm, or 20ppm maximum v cc -1.025v dc minimum v cc -1.085v dc minimum v cc -1.620v dc maximum v cc -1.555v dc maximum 300psec typical, 700psec maximum 50 5(%) 50 ohms into v cc -2.0v dc tri-state and complementary output enables output enables output disables output: high impedance 30a maximum 10 mseconds maximum 0.4psec typical, 1 psec maximum -60dbc/hz at 10hz offset -95dbc/hz at 100hz offset -125dbc/hz at 1khz offset -143dbc/hz at 10khz offset -145dbc/hz at 100khz offset -145dbc/hz at 1mhz offset -146dbc/hz at 10mhz offset nominal frequency (mhz) operating temperature range storage temperature range supply voltage (v cc ) input current frequency tolerance / stability output voltage logic high (v oh ) output voltage logic low (v ol ) rise time / fall time duty cycle load drive capability logic control / additional output tri-state input voltage standby current start up time rms phase jitter typical phase noise 77.76mhz to 159.999999mhz 160mhz to 312.5mhz inclusive of all conditions: calibration tolerance at 25c, frequency stability over the operating temperature range, supply voltage change, output load change, 1st year aging at 25c, shock, and vibration 0c to 85c -40c to 0c 0c to 85c -40c to 0c 20% to 80% of waveform at 50% of waveform v ih of 70% of v cc minimum no connection v il of 30% of v cc maximum without load fj = 12khz to 20mhz fo=156.250mhz h 2.0 l 7.0 w 5.0 77.76, 78.125, 80, 80.157, 85, 87.125, 90, 100, 106.25, 110, 119, 120, 122.888, 124.4, 125, 127, 128, 131.072, 133, 133.33, 133.333, 135, 137.472, 150, 155.52, 156.25, 159.375, 161.1328, 162.5, 163.84, 164.355, 164.355469, 166, 166.67, 167.3316, 170, 173.3705, 175, 176.83816, 187.5, 187.509375, 187.5103, 200, 212.5, 240, 250, or 312mhz
line 1: ecliptek line 2: xx.xxx m frequency in mhz (5 digits maximum + decimal) line 3: xx y zz week of year last digit of year ecliptek manufacturing identifier manufacturer category series package voltage class rev . date ecliptek corp. oscillator e13c7 ceramic 3.3v os1m 01/09 mechanical dimensions all dimensions in millimeters environmental/mechanical specifications marking specifications tape and reel dimensions all dimensions in millimeters suggested solder pad layout all dimensions in millimeters 800-ecliptek www.ecliptek.com for latest revision specifications subject to change without notice. e13c7 e 2 f - 155.520m tr part numbering guide available options blank=tubes tr=tape and reel (standard) frequency logic control/additional output f=tri-state and complementary output duty cycle 2=50 5(%) frequency tolerance & stability/ operating temperature range c=100ppm maximum over 0c to +70c d=50ppm maximum over 0c to +70c e=25ppm maximum over 0c to +70c (*) f=20ppm maximum over 0c to +70c (*) g=100ppm maximum over -40c to +85c h=50ppm maximum over -40c to +85c j=25ppm maximum over -40c to +85c (*) a b c d e f 16.3-.1 7.5.1 6.75.1 4 .1 2.1 f g h j k l 8.1 b0* 1.5 +.1-0 a0* .3 .05 k0* tape m n o p q 1.5 min 50 min 20.2 min 13.2 40 min r s t u v qty/reel 2.5 min 10 min 22.4 max 360 max 16.4+2-0 1,000 reel *compliant to eia 481a tolerances= +0.1 marking orientation 5.00 0.15 7.00 0.15 5.08 0.15 2.54 typ 1.2 0.2 2.60 0.15 1 2 3 4 5 6 1.4 0.1 2.00 max characteristic specification fine leak test mil-std-883, method 1014, condition a gross leak test mil-std-883, method 1014, condition c mechanical shock mil-std-202, method 213, condition c vibration mil-std-883, method 2007, condition a solderability mil-std-883, method 2002 temperature cycling mil-std-883, method 1010 resistance to soldering heat mil-std-202, method 210 resistance to solvents mil-std-202, method 215 pin 1: tri-state pin 2: no connect pin 3: case ground pin 4: output pin 5: complementary output pin 6: supply voltage (*) not available over nominal frequency range of 212.500001mhz to 312.500mhz
|