www.vishay.com 118 sogc 01, 03, 05 vishay dale document number: 31506 revision 01-aug-02 for technical questions, contact: ff2aresistors@vishay.com 05 schematic 16 20 number of leads 01 03 schematic sogc model 05 schematic g tolerance f= 1% g= 2% j= 5% xxx or xxxx r 2 value xxx or xxxx r 1 value first 2 digits (3 for f tolerance) are significant figures. last digit specifies number of zeros to follow. sogc model f= 1% g= 2% j= 5% g tolerance first 2 digits (3 for f tolerance) are significant figures. last digit specifies number of zeros to follow. xxx or xxxx r 1 value 16 20 number of leads 01, 03 schematic ordering information thick film resistor networks, dual-in-line, small outline molded dip, 01, 03, 05 schematics, 16 or 20 pins features 0.110" [2.79mm] maximum seated height rugged, molded case construction 0.050" [1.27mm] lead spacing ? reduces total assembly costs ? compatible with automatic surface mounting equipment ? uniform performance characteristics ? meets eia pdp 100, sogn-0003 outline dimensions ? available in tube pack or tape and reel pack model schematic resistor package tolerance resistance operating temperature circuit power range voltage coefficient w @ 70 c w @ 70 c % ? vdc ppm/ c sogc-16 01 0.1 1.6 2 (1, 5*) 10-1m0 50 max 100 03 0.19 1.6 2 (1, 5*) 10-1m0 50 max 100 05 0.1 1.6 2 (5*) 10-1m0 50 max 100 sogc-20 01 0.1 2.0 2 (1, 5*) 10-1m0 50 max 100 03 0.19 2.0 2 (1, 5*) 10-1m0 50 max 100 05 0.1 2.0 2 (5*) 10-1m0 50 max 100 parameter unit s0gc-16 / -20 package power rating (max. at + 70 c) w 1.6 / 2.0 tc tracking (- 55 c to + 125 c) ppm/ c 50 voltage coefficient of resistance: ppm/v < 50 typical. maximum operating voltage: vdc 50 operating temperature range: c - 55 to + 125. storage temperature range: c - 55 to + 150 standard electrical specifications * tolerances in brackets available upon request. ? 100 milliohm maximum on zero ohm jumper technical specifications marking: model number, schematic number, value tolerance, pin 1 indicator, date code. marking resistance permanency testing per to solvents: mil-std-202, method 215. maximum solder reflow temperature: + 255 o c solderability: per mil-std-202, method 208e. terminals: copper alloy. 60/40 solder dipped terminal. body: molded epoxy. mechanical specifications
www.vishay.com 119 sogc 01, 03, 05 vishay dale document number: 31506 revision 01-aug-02 for technical questions, contact: ff2aresistors@vishay.com test max. ? r (typical test lots) power conditioning 0.50% ? r thermal shock 0.50% ? r short time overload 0.25% ? r low temperature operation 0.25% ? r moisture resistance 0.50% ? r resistance to soldering heat 0.25% ? r shock 0.25% ? r vibration 0.25% ? r load life 0.50% ? r terminal strength 0.25% ? r insulation resistance 10,000 megohm (minimum) dielectric withstanding voltage no evidence of arcing or damage (200 v rms for 1 minute) performance a 0.045 [1.14] ref. 0.018 [0.457] typ. 0.050 [1.27] non-accum. typ. 0.006 [0.152] max. typ. 0.295 [7.49] 0.010 .005 [0.254 0.127] 0.406 0.012 [10.31 0.305] 0.105 [2.67] 0.100 [2.54] 0.028 0.010 [0.711 0.254] typ. 0.008 [0.203] sogc-16 sogc-20 0.440 [11.18] 0.540 [13.72] 0.350 [8.89] 0.450 [11.43] b model b 0.045 [1.14] a dimensions in inches [millimeters] thick film resistor networks, small outlline, molded, dip power rating (watts) ambient temperature c - 50 0 + 25 + 70 + 125 + 150 2.0 1.6 1.0 0.19 0.10 single resistor sogc-xx03 sogc-xx01 & 05 sogc-2001, 03, 05 pkg. sogc-1601, 03, 05 pkg. derating 8 or 10 isolated resistors the sogc-xx03 circuit provides a choice of 8 or 10 nominally equal resistors with each resistor isolated from all others and wired directly across. commonly used in the following applications: "wired or" pull-up long-line impedance balancing power driven pull-up led current limiting powergate pull-up ecl output pull-down line termination ttl input pull-down ttl dual-line terminator; pulse squaring, 14 or 18 pairs of resistors (r 1 resistors are common to leads 16 or 20) (r 2 resistors are common to leads 8 or 10) the sogc-xx05 circuit contains 14 or 18 pairs of resistors. each pair is connected between ground and a common line. the junctions of these resistor pairs are connected to the input leads. the 05 circuits are designed for ttl dual-line termination and pulse squaring. sogc-16, sogc-20 pin 1 15 or 19 resistors with one pin common the sogc-xx01 circuit provides a choice of 15 or 19 nominally equal resistors, each connected between a common lead (16 or 20) and a discrete pc board pin. commonly used in the following applications: mos/rom pull-up/pull-down ttl input pull-down open collector pull-up digital pulse squaring "wired or" pull-up ttl unused gate pull-up power driven pull-up high speed parallels pull-up circuit applications pin 1 sogc-16 sogc-20 01 schematic 03 schematic 05 schematic r1 r1 r1 r1 r2 r2 r2 r2 r1 r1 r1 r2 r2 r2 r2 r2 r2 r1 r1 r1 r1 r1 r1 r1 r2 r2 r2 r2 sogc-16 sogc-20 pin 1 pin 1 sogc
|
