originator: c. eng date: 3/9/2012 document no. doc002323 rev a P1RX6B-SX51-02A product spec sheet sheet 1 of 8 confidential information P1RX6B-SX51-02A product specification sheet
originator: c. eng date: 3/9/2012 document no. doc002323 rev a P1RX6B-SX51-02A product spec sheet sheet 2 of 8 confidential information 1.0 features ? 5 receive lanes and 1 transmit lane over a single multimode fiber ? low power consumption (1.1w) ? mechanical enclosure serves as heat sink while allo wing for fcc part 15 class a compliance ? no manipulating or compressing the data ? small footprint ? high-speed cml outputs this device is extremely sensitive to electrostatic discharge (esd). at a minimum, all handling must be performed in accordan ce with an ansi-compliant esd control program (ansi/esd s20.20-2007) to mitigate possible esd-induced damage. reliability and life of the device will be adversel y affected if these precautions are not met. this device is a class 3r laser device and can caus e damage to eye sight if used improperly. refer to ansi z136 for proper handling and usage of class 3r devices.
originator: c. eng date: 3/9/2012 document no. doc002323 rev a P1RX6B-SX51-02A product spec sheet sheet 3 of 8 confidential information 2.0 absolute maximum ratings parameter symbol min typ max units storage temperature 1 tst c supply voltage 2 3 vcc v operating surface temperature 4 ta c operating humidity 5 rh % input voltage 6 v in v 3.0 optical characteristics C high-speed lanes parameter (per lane) symbol min typ max units wavelength C lane 0 778 nm wavelength C lane 1 800 nm wavelength C lane 2 825 nm wavelength C lane 3 850 nm data rate 7 sx51v sx51d gb/s peak optical input power pin dbm peak optical modulation power pin dbm oma sensitivity 8 -16.00 dbm input data pattern dc-balanced 1 stresses listed may be applied without causing dama ge. functionality at or above the values listed is not implied. exposure to these values for extended periods may affect reliability. 2 supply voltage must be present before input signal may be applied 3 module must be powered down (off) before installati on/removal. 4 see outline drawing for measurement point. omron strongly recommends mounting with a heat sink. 5 non condensing. do not operate device if wet. 6 supply voltage must be present before input signal may be applied. driving the device in a power off state may result in permanent damage to the input pins. 7 requires dc-balanced data pattern. 8 optical modulation amplitude. based on an unstress ed input signal.
originator: c. eng date: 3/9/2012 document no. doc002323 rev a P1RX6B-SX51-02A product spec sheet sheet 4 of 8 confidential information 4.0 electrical specifications C high-speed lanes parameter symbol min typ max units low frequency cutoff f cutoff 175 khz total jitter (rms), per lane 9 t j1 10 ps differential output voltage 10 v od 500 mvp-p loss of signal assert sensitivity los sen-on -14.50 dbm loss of signal de-assert sensitivity los sen-off -13.00 dbm loss of signal output low 11 v los v loss of signal output high v los v operating supply voltage vcc-vee 3.30 v operating supply current icc ma 5.0 optical characteristics C bi-directional lanes receive parameter symbol min typ max units wavelength - lane 4 911 nm data rate mb/s peak optical input power pin dbm peak optical modulation power pin dbm oma sensitivity 12 -15.00 dbm input data pattern dc-balanced transmit parameter symbol min typ max units average optical power - lane 5 pavg -1.5 dbm optical modulation amplitude 0.0 dbm wavelength - lane 5 980 nm optical rise/fall time 2000 ps 9 based on a jitter-free source 10 differential back-terminated cml outputs 11 this output is asserted low when a loss of signal i s detected on all lanes 12 optical modulation amplitude. based on an unstress ed input signal.
originator: c. eng date: 3/9/2012 document no. doc002323 rev a P1RX6B-SX51-02A product spec sheet sheet 5 of 8 confidential information 6.0 electrical specifications C bi-directional lane s receive parameter symbol min typ max units low frequency cutoff f cutoff 35 khz total jitter (rms) 13 t j1 25 ps differential output voltage 14 v od 835 mvp-p loss of signal assert sensitivity los sen-on -15.5 dbm loss of signal de-assert sensitivity los sen-off -13.5 dbm loss of signal output low v los v loss of signal output high 15 v los v transmit parameter symbol min typ max units data rate per lane 155 mb/s input differential impedance 100 ohm differential input voltage C lane 5 2,16 mvp-p input data pattern dc-balanced 7.0 laser safety the p1rx6-sx51-02 meets class-3r requirements. 17 please use proper eye protection and handling practices per ansi z136.1. 13 based on a jitter-free source 14 differential back-terminated cml outputs 15 this output is asserted low when a loss of signal is detected on all lanes 16 differential cml compatible inputs 17 lane 4 data input with 50% duty cycle
originator: c. eng date: 3/9/2012 document no. doc002323 rev a P1RX6B-SX51-02A product spec sheet sheet 6 of 8 confidential information 8.0 pin numbers and descriptions 18 the rx data module contains a 30 pin connector (df1 2-30ds-0.5v(86)). for information on the specifications of the mating con nector (df12(4.0)-30dp- 0.5v(86)), contact hirose. pin # signal name description 1 gnd ground 2 los hi high speed los loss of signal C high speed channel s 3 + td0 ch 0 + data output positive differential outp ut for 778nm lane 4 los bi ch 4 los loss of signal C bi-directional channel 5 - td0 ch 0 - data output negative differential outp ut for 778nm lane 6 reset reset microcontroller reset 19 7 + td1 ch 1 + data output positive differential outp ut for 800nm lane 8 uart uart_tx reserved for future use 9 - td1 ch 1 - data output negative differential outp ut for 800nm lane 10 uart uart_rx reserved for future use 11 + td2 ch 2 + data output positive differential outp ut for 825nm lane 12 nc no connect reserved for future use 13 - td2 ch 2 - data output negative differential outp ut for 825nm lane 14 nc no connect reserved for future use 15 + td3 ch 3 + data output positive differential outp ut for 850nm lane 16 en bi enable enable 20 C bi-directional laser 17 - td3 ch 3 - data output negative differential outp ut for 850nm lane 18 nc no connect reserved for future use 19 gnd ground 20 nc no connect reserved for future use 21 - in5 ch 5 - data input negative differential input for 980nm lane 22 nc no connect reserved for future use 23 + in5 ch 5 - data input positive differential input for 980nm lane 24 nc no connect reserved for future use 25 + td4 ch 4 - data output positive differential outp ut for 911nm lane 26 nc no connect reserved for future use 27 - td4 ch 4 - data output negative differential outp ut for 911nm lane 28 vcc 2 voltage input +3.3 volt input 29 gnd ground 30 vcc 2 voltage input +3.3 volt input 18 verify pin assignments and polarity before powering on device 19 reset must be pulled high for normal operation 20 enable to be pulled up to vcc for normal operation
originator: c. eng date: 3/9/2012 document no. doc002323 rev a P1RX6B-SX51-02A product spec sheet sheet 7 of 8 confidential information 9.0 environmental standards omron network products designs and manufactures its products to minimize the negative impact on our environment. as such, the p1rx6b-sx51-02 conforms to a variety of environmental and safety standards standard compliant certificate available rohs yes yes reach yes yes fcc part 15 class a yes no
originator: c. eng date: 3/9/2012 document no. doc002323 rev a P1RX6B-SX51-02A product spec sheet sheet 8 of 8 confidential information 10.0 dimensions the sx51-02 data module is designed to work with a standard sc ferrule only. insertion of any other type may result in damage. dimensions and orientation are for reference only . customers can request final, detailed dimensions, or a cad drawing, throu gh your omron sales representative. dimensions are in mm temperature measurement point
|
