data sheet le9033/tr3 lead-free parts pb ligitek electronics co.,ltd. property of ligitek only surface mount tape and reel doc. no : qw0905-le 9033/tr3 rev. : a date : 18 - jul. - 2005
note : the tolerances unless mentioned is ? 0.2mm,angle ? 0.5. unit=mm. note : 1.all dimension are in millimeter tolerance is ? 0.2mm unless otherwise noted. 2.specifications are subject to change without notice. polarity carrier type dimensions package dimensions 1/7 page ligitek electronics co.,ltd. property of ligitek only part no. : le9033/tr3 cathode 2.0 0.5 ? 0.1 0.13typ 0.76max 2.8 0.61typ 7.62max 0.31typ 1.07typ 1.4 0.4 ? 0.1 2.5 2.0 12.00.3 9.3 4.0 3.37 4.0 1.75 0.35 5.5 2.52 7.84 r 1.5 r 1.9
r 178 ? 2.0 part no. le9033/tr3 description 12.0mm tape,7"reel quantity/reel 1500 devices 14.2 ? 1.0 74.0 ? 1.5 16.0 ? 1.0 reel dimensions page 2/7 ligitek electronics co.,ltd. property of ligitek only part no. : le9033/tr3
min. 20 max 260 j for 5 sec max (2mm from body) luminous intensity @10ma(mcd) color water clear note : 1.the forward voltage data did not including ? 0.1v testing tolerance. 2. the luminous intensity data did not including ? 15% testing tolerance. le9033/tr3 part no emitted gaasp/gap orange material lens 635 peak wave length f pnm max. min. 1.7 45 2.6 forward voltage @20 ma(v) spectral halfwidth ??f nm typical electrical & optical characteristics (ta=25 j ) storage temperature soldering temperature operating temperature tstg tsol t opr -40 ~ +100 -40 ~ +85 typ. 20 40 viewing angle 2 c 1/2 (deg) j j ligitek electronics co.,ltd. property of ligitek only absolute maximum ratings at ta=25 j reverse current @5v power dissipation peak forward current duty 1/10@10khz forward current parameter ir pd i fp i f 10 100 120 30 symbol ratings e g a mw ma ma unit page 3/7 part no. : le9033/tr3
fig.3 forward voltage vs. temperature fig.5 relative intensity vs. wavelength ambient temperature( j ) relative intensity@20ma wavelength (nm) forward voltage@20ma normalize @25 j fig.4 relative intensity vs. temperature ambient temperature( j ) relative intensity@20ma normalize @25 j typical electro-optical characteristics curve forward voltage(v) fig.1 forward current vs. forward voltage forward current(ma) forward current(ma) fig.2 relative intensity vs. forward current relative intensity normalize @20ma ligitek electronics co.,ltd. property of ligitek only 1.0 0.1 1.0 10 100 1000 1.0 10 100 1000 0.0 0.5 1.0 1.5 2.0 2.5 3.0 -40 -20 0 20 40 60 1.0 1.1 1.2 550 600 0.0 0.5 1.0 2.0 3.0 4.0 5.0 80 100 0.8 0.9 -20 -40 40 20 080100 60 2.0 0.0 0.5 1.0 1.5 2.5 3.0 650 700 750 e chip page 4/7 part no. : le9033/tr3 fig.6 directive radiation 25% 75% -60 x 100% 25% 50% 0 -30 x 0 x 75% 50% 60 x 100% 30 x
ligitek electronics co.,ltd. property of ligitek only page 5/7 1. hand solder basic spec is ?? 280 j 3 sec one time only. recommended soldering conditions 2. wave solder preheat 180~200 c reflow soldering should not be done more than two times. 120 sec.max. 1~5 c/sec above 220c 60 sec.max. 120 ~ 180 sec 120 3-2 pb-free reflow solder 60 ~ 120 sec temp. ( j ) 240 3-1. lead reflow solder 150 preheat rising +5 j /sec time 5sec 1~5 c/sec 260 c max. 10sec.max cooling -5 j /sec 120 ~ 150 j preheat 245 ? 5 j within 5 sec soldering heat max. 260 j part no. : le9033/tr3
led led (a) recommended circuit. (b) the difference of brightness between led could be f ound due to the vf-if characteristics of led. cleaning: use alcohol-based cleaning solvents such as isopropyl alc ohol to clean the led. esd(electrostatic discharge): static electricity or power surge will damage the led. use of a c onductive wrist band or anti-electrosatic glove is recommended when handing these led. all devices, equipment and machinery must be properly grounded. drive method: led is a current operated device, and therefore, require r some kind of current limiting incorporated into the driver circuit. this current limiting typically takes the form of a current limiting resistor placed in series with the led. consider worst case voltage variations than could occur across the current limiting resistor. the forwrd current should not be allowed to c hange by more than 40 % of its desired value. circuit model a precautions for use: storage time: 1.the operation of temperatures and rh are : 5 j ~35 j ,rh60%. 2.once the package is opened, the products s hould be used within a week. otherwise, they should be kept in a damp proof box with descanting agent. considering the tape life, we suggest our customers to use our pr oducts within a year(from production date). 3.if opened more than one week in an atmos phere 5 j ~ 35 j ,rh60%, they should be treated at 60 j? 5 j fo r 15hrs. circuit model b ligitek electronics co.,ltd. property of ligitek only 6/7 page part no. : le9033/tr3
page ligitek electronics co.,ltd. property of ligitek only 7/7 reliability test: classification endurance test environmental test low temperature storage test 1.ta=-40 j? 5 j 2.t=1000 hrs (-24hrs, + 72hrs) 1.ta=105 j? 5 j &-40 j? 5 j (10min) (10min) 2.total 10 cycles 1.105 j ~ 25 j ~ - 55 j ~ 25 j 30mins 5mins 30mins 5mins 2.10 cyeles 1.t.sol=235 j? 5 j 2.immersion time 2 ? 0.5sec 3.coverage ? 95% of the dipped surface 1.t=260 c max. 10sec.max. 2. 6 min temperature cycling ir reflow thermal shock test high temperature high humidity storage test solderability test 1.ta=65 j? 5 j 2.rh=90 %~95% 3.t=1000hrs ? 2hrs mil-std-202f: 208d mil-std-750d: 2026 mil-std-883d: 2003 iec 68 part 2-20 jis c 7021: a-2 mil-std-750d:2031.2 j-std-020 mil-std-202f: 107d mil-std-750d: 1051 mil-std-883d: 1010 jis c 7021: a-4 mil-std-202f: 107d mil-std-750d: 1051 mil-std-883d: 1011 jis c 7021: b-12 mil-std-202f:103b jis c 7021: b-11 test condition 1.ta=105 j? 5 j 2.t=1000 hrs (-24hrs, + 72hrs) 1.ta=under room temperature as per data sheet maximum rating. 2.if=20ma 3.t=1000 hrs (-24hrs, + 72hrs) test item operating life test high temperature storage test mil-std-750d: 1026 mil-std-883d: 1005 jis c 7021: b-1 mil-std-883d:1008 jis c 7021: b-10 reference standard part no. : le9033/tr3
|
