View MIC2040_5960079.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

january 2004 1 m9999-012004 MIC2040/2041 micrel MIC2040/2041 single channel low voltage power distribution switch general description the MIC2040 and mic2041 are high side mosfet switches optimized for general purpose power distribution applications that require circuit protection. the devices switch up to 5.5v and as low as 0.8v while offering both programmable current limiting and thermal shutdown to protect the device and the load. a fault status output is provided in order to detect overcurrent and thermal shutdown fault conditions. both devices employ soft start circuitry to minimize the inrush current in applications that employ highly capacitive loads. additionally, the MIC2040/41 is suited for multi-port usb applications to satisfy upstream/downstream power require- ments. the mic2041 features a auto-reset circuit breaker mode that latches the output off upon detecting an overcurrent condition lasting more than 28ms. the output is reset by removing or reducing the load. data sheets and support documentation can be found on micrel? web site at www.micrel.com. typical application 7, 9 6 1 2 5 8,10 3 r set 340 ? note: bothv in pins (7, 8) must be externally tied together. bothv out pins (8, 10) must be externally tied together. i limit = 1a. c3 4.7 f logic controller on/off overcurrent in 4 MIC2040-1bm vbias vin en /fault ilim vout uvloin gnd +3.3v power supply r1 20k ? c load 33 f (open) v out 3.3v@ 1a c2 0.1 f c1 0.1 f features 75m ? max. on-resistance 0.8v to 5.5v operating range adjustable current limit up to 1.5a continuous output current short circuit protection with thermal shutdown circuit breaker mode (mic2041) fault status flag undervoltage lockout output mosfet reverse current flow block when disabled very fast reaction to short-circuits low quiescent current applications docking stations notebook pcs pdas board hot swap raid controllers usb peripherals acpi power distribution micrel, inc. ?1849 fortune drive ?san jose, ca 95131 ?usa ?tel + 1 (408) 944-0800 ?fax + 1 (408) 944-0970 ?http://www.mic rel.com ordering information part number enable circuit breaker package MIC2040-1bmm active-high 10-pin msop MIC2040-2bmm active-low 10-pin msop mic2041-1bmm active-high x 10-pin msop mic2041-2bmm active-low x 10-pin msop
MIC2040/2041 micrel m9999-012004 2 january 2004 pin configuration ilim vbias 6 5 1 en /fault uvloin gnd 10 vout vin vout vin 9 8 7 2 3 4 MIC2040/mic2041 10-pin msop (mm) pin description pin number pin name pin function 1 en switch enable input: gate control pin of the output mosfet available as an active high (?) or active low (?) input signal. 2 /fault fault status output: open drain n-channel device, active low. this pin indicates an overcurrent, or thermal shutdown condition. for an overcurrent event, /fault is asserted if the duration of the overcurrent condition lasts longer than 28ms. 4 gnd ground connection: tie to analog ground. 5 ilim current limit set: a resistor, r set , connected to this pin sets the current limit threshold as clf/r set , where clf is the current limit factor specified in the electrical characteristics table. for the MIC2040/41, the continuous output current range is 0.25a to 1.5a. 7, 9 vin switch input supply: the drain of the output mosfet. the range of input for the switch is 0.8v to 5.5v. these pins must be externally connected together. 8, 10 vout switch output: the source of the output mosfet. these pins must be externally connected together. 6 vbias bias supply input: this input pin supplies bias to operate the switch with range from 1.6v to 5.5v. when switching voltage (v in ) is between 1.6v to 5.5v and the use of a single supply is desired, connect vbias to vin externally. 3 uvloin undervoltage lockout adjust input: with this pin left open, the uvlo threshold is internally set to 1.45v. when the switching voltage (v in ) is at or below 1.6v, connecting an external resistive divider to this input will lower the uvlo threshold. the total resistance must be less than 200k ? . see ?pplications information for further detail.
january 2004 3 m9999-012004 MIC2040/2041 micrel absolute maximum ratings (1) v in and v bias .................................................................................. 6v /fault, pwrgd output voltage ................................... 6v /fault, pwrgd output current .............................. 25ma junction temperature range ................... internally limited esd rating (3) human body model ................................................... 2kv machine model ........................................................ 200v operating ratings (2) supply voltage v in ............................................................... 0.8v to 5.5v v bias ........................................................... 1.6v to 5.5v continuous output current ........................... 0.25a to 1.5a ambient temperature (t a ) ........................... ?0 c to 85 c package thermal resistance ( r (j-a) ) msop ................................................................ 160 c/w electrical characteristics (4) v in = v bias = 5v. t a = 25 c unless specified otherwise. bold indicates ?0 c to +85 c. symbol parameter condition min typ max units v in switch input voltage v in v bias 0.8 5.5 v v bias bias supply voltage 1.6 5.5 v i bias vbias supply current - switch off no load 0.1 5 a vbias supply current - switch on no load 250 400 a note 5 v en enable input voltage v il(max) 2.4 1.5 v v ih(min) 3.5 2.5 v v enhys enable input threshold hysteresis 100 mv i en enable input current v en = 0v to 5.5v ? .01 1 a r ds(on) switch resistance v in = v bias = 3v, 5v 50 75 m ? i out = 500ma i leak output leakage current output off 10 a clf current limit factor (6) v in = 3v, 5v; 0.5v v out < 0.5v in 280 340 400 a ? 0.25a i out 1.5a v latch output reset threshold v in = 0.8v to 5.5v v in ?0.2 v v out rising (mic2041) i latch latched output off current output latched off (mic2041) 1 3 5 ma v ol output low voltage i ol (/fault) = 15ma 0.4 v (/fault) i off /fault off current v fault = 5v 1 a v uv undervoltage lockout threshold v in rising 1.30 1.45 1.58 v v in falling 1.20 1.35 1.50 v v uvhys undervoltage lockout 100 mv threshold hysteresis v uvinth uvlo adjust pin threshold voltage v in rising 200 220 240 mv v in falling 180 200 220 mv v uvinhys uvlo adjust pin threshold hysteresis 20 mv overtemperature threshold t j increasing 140 c t j decreasing 120 c notes: 1. exceeding the absolute maximum rating may damage the device. 2. the device is not guaranteed to function outside its operating rating. 3. devices are esd sensitive. handling precautions recommended. human body model, 1.5k in series with 100pf. 4. specification for packaged product only. 5. off is v en < 1.0v for MIC2040/mic2041? and v en > 4.0v for MIC2040/mic2041 ?. on is v en > 4.0v for MIC2040/mic2041? and v en < 1.0v for MIC2040/mic2041 ?. 6. the current limit is determined as follows: i lim = clf/r set .
MIC2040/2041 micrel m9999-012004 4 january 2004 electrical characteristics (7) symbol parameter condition min typ max units t flag flag response delay v in = v bias = 3v, 5v 21 28 35 ms t on output turn-on delay, r load = 10 ? , c load = 1 f 400 600 800 s t r output turn-on rise time r load = 10 ? , c load = 1 f 0.5 1 1.5 ms t off output turn-off delay r load = 10 ? , c load = 1 f15 s t f output turn-off fall time r load = 10 ? , c load = 1 f24 s note: 7. specification for packaged product only. timing diagrams

figure 1. turn-on/turn-off delay 0 v en i limit 0 v out 0 i out 0 /fault t flag v in 0.2v increase the load figure 2. overcurrent fault response ?MIC2040-2
january 2004 5 m9999-012004 MIC2040/2041 micrel test circuit

MIC2040/2041 micrel m9999-012004 6 january 2004 typical characteristics 100 150 200 250 300 350 400 450 500 -40 -20 0 20 40 60 80 100 supply current ( a) temperature ( c) supply current vs. temperature v in =v bias =1.6v v in =v bias = 5.5v v in =v bias = 3v 0 0.5 1 1.5 2 2.5 3 3.5 -40 -20 0 20 40 60 80 100 v en (v) temperature ( c) enable input threshold (falling) vs. temperature v bias = 5.5v v bias = 3v v bias = 1.6v 0 0.5 1 1.5 2 2.5 3 3.5 -40 -20 0 20 40 60 80 100 v en (v) temperature ( c) enable input threshold (rising) vs. temperature v bias = 5.5v v bias = 3v v bias = 1.6v 0 300 600 900 1200 1500 1800 2100 2400 2700 3000 -40 -20 0 20 40 60 80 100 output leakage (na) temperature ( c) output leakage current vs. temperature v bias = 5.5v v bias = 3v v bias = 1.6v 0 10 20 30 40 50 60 70 80 -40 -20 0 20 40 60 80 100 rds(m ? ) temperature ( c) on resistance (r ds(on) ) vs. temperature v in =v bias = 5v v in =v bias = 3v v in =v bias = 1.6v 300 310 320 330 340 350 360 370 380 390 400 -40 -20 0 20 40 60 80 100 current limit factor (v) temperature ( c) current limit factor vs. temperature v bias = 5.5v v bias = 3v v bias = 1.6v r set = 0.4a 300 310 320 330 340 350 360 370 380 390 400 -40 -20 0 20 40 60 80 100 current limit factor (v) temperature ( c) current limit factor vs. temperature v bias = 5.5v v bias = 3v v bias = 1.6v r set = 0.85a 300 310 320 330 340 350 360 370 380 390 400 -40 -20 0 20 40 60 80 100 current limit factor (v) temperature ( c) current limit factor vs. temperature v bias = 5.5v v bias = 3v v bias = 1.6v r set = 1.5a 0 50 100 150 200 250 300 -40 -20 0 20 40 60 80 100 v ol (mv) temperature ( c) output low voltage vs. temperature v bias = 5.5v v bias = 3v v bias = 1.6v i ol (/fault) = 15ma 1.2 1.25 1.3 1.35 1.4 1.45 1.5 1.55 -40 -20 0 20 40 60 80 100 uvlo (v) temperature ( c) uvlo threshold vs. temperature uvlo+ uvlo 180 185 190 195 200 205 210 215 220 225 230 235 240 -40 -20 0 20 40 60 80 100 uvlo (v) temperature ( c) uvlo adjust pinthreshold vs. temperature uvlo+ uvlo 20 25 30 35 40 45 50 -40 -20 0 20 40 60 80 100 t flag (ms) temperature ( c) flag response delay vs. temperature t flag = 3v t flag = 5v
january 2004 7 m9999-012004 MIC2040/2041 micrel typical characteristics (continued) 350 400 450 500 550 600 650 700 750 800 -40 -20 0 20 40 60 80 100 turn on delay ( s) temperature ( c) turn on delay vs. temperature v in =v bias = 5.5v v in =v bias = 3v v in =v bias = 1.6v 350 400 450 500 550 600 650 700 750 800 -40 -20 0 20 40 60 80 100 t on (?) temperature ( c) output rise time vs. temperature v in =v bias = 5.5v v in =v bias = 3v v in =v bias = 1.6v
MIC2040/2041 micrel m9999-012004 8 january 2004 functional diagram

!
" # #" $# % & ' () % * & +), %' -&. - " /
"/$ & &
/ ."" .$ 0 1( 23 / $ /# 4/56
2"
!" /# "7 13 7 4! '7 $ 7!"/5
4/56 2"
january 2004 9 m9999-012004 MIC2040/2041 micrel functional characteristics turn-on response time (1ms/div.) i out (1a/div.) en (5v/div.) v out (2v/div.) v in = v bias =5v r load = 5 ? c load = 47 f turn-off response time (500 s/div.) i out (1a/div.) en (5v/div.) v out (2v/div.) v in = v bias = 5v r load = 5 ? c load = 47 f latched output - mic2041 time (5ms/div.) i out (1a/div.) en (5v/div.) v out (5v/div.) /fault (5v/div.) v in = v bias = 5v r load = 35 ? c load = 57 f latched output reset - mic2041 time (50ms/div.) en (5v/div.) v out (2v/div.) /fault (5v/div.) v in = v bias = 5v r load = 35 ? c load = 57 f current-limit response time (5ms/div.) i out (1a/div.) en (5v/div.) v out (5v/div.) /fault (5v/div.) v in = v bias = 5v r load = 3.5 ? c load = 47 f uvlo response time (10ms/div.) i out (500ma/div.) v in (1v/div.) v out (1v/div.) v en ramps 0 to 1.6v r load = 1.6 ? c load = 47 f
MIC2040/2041 micrel m9999-012004 10 january 2004 thermal shutdown response time (100ms/div.) i out (1a/div.) en (5v/div.) v out (5v/div.) /fault (5v/div.)
january 2004 11 m9999-012004 MIC2040/2041 micrel functional description the MIC2040 and mic2041 are high-side n-channel switches equipped with programmable current limit up to 1.5a for use in general purpose power distribution applications. the switches, available with active-high or active-low enable inputs, operate down to 0.8v and provide circuit protection via thermal shutdown and an optional output latch during overcurrent conditions. input and output vbias supplies power to the internal circuitry of the switch and must be present for the switch to operate. vin is con- nected to the drain of the output mosfet and sources power to the switched load. vin must be less than or equal to vbias. vout is the source terminal of the output mosfet and attaches to the load. in a typical circuit, current flows from vin to vout toward the load. if vout is greater than vin, current will flow from vout to vin since the switch is bi-directional when the device is enabled. when disabled (off), the switch will block current flow from either direction. enable input enable, the on/off control for the output switch, is a digital input available as an active-high (?) or active-low (?) signal. the en pin, referenced to approximately 0.5 vbias, must be driven to a clearly defined logic high or logic low. failure to observe this requirement, or allowing en to float, will cause the MIC2040/41 to exhibit unpredictable behavior. en should not be allowed to go negative with respect to ground, nor allowed to exceed vbias. failure to adhere to these conditions may result in damage to the device. undervoltage lockout when the switch is enabled, undervoltage lockout (uvlo) monitors the input voltage, vin, and prevents the output mosfet from turning on until vin exceeds a predetermined level, nominally set at 1.45v. the uvlo threshold is adjust- able and can be varied by applying an external resistor divider to the uvloin pin from vin to gnd. the resistive divider network is required when the input voltage is below 1.5v. the uvlo threshold is internally preset to 1.45v if the uvloin pin is left open. see ?pplications information. programmable current limit the MIC2040/41 is designed to prevent damage to the external load by limiting the maximum amount of current it can draw. the current limit is programmed by an external resistor (r set ) connected from ilim to ground and becomes active when the output voltage is at least 200mv below the voltage at the input to the device. the limiting current value is defined by the current limit factor (clf) divided by r set , and the MIC2040/41 will limit from 0.25a to 1.5a with a set point accuracy of 18%. in programming the nominal current limit, the value of r set is determined using the following equation: r clf i 340a i set lim lim == ? () (1) and given the 18% tolerance of the current limit factor (clf), the external resistor is bound by: 187 ? r set 1.6k ? (2) the graph below (figure 3) displays the current limit factor characteristic over the full temperature and voltage range indicated on the graph. this curve can be used as a point of reference in determining the maximum variation in the device? current limit over the full temperature range. for example: with v in = v bias = 3.0v and a nominal 1a current limit (r set = 340 ? ), the low and high current limit settings for the MIC2040/41 would be approximately 0.82a and 1.18a, re- spectively, as shown on the graph using the 340 ? reference. the mic2041 is equipped with an internal circuit breaker for overcurrent protection. during an overcurrent event which exceeds the flag delay, the /fault output is asserted and the mic2041 latches the output off. once the overcurrent load is removed, the output automatically resets. 0 0.25 0.5 0.75 1 1.25 1.5 1.75 2 2.25 2.5 150 300 450 600 750 900 1050 1200 1350 1500 i lim (a) r set ( ? ) current limit vs. r set clf (lo) v in = 1.6v to 5v ?0 c to +85 c clf (hi) figure 3. current limit factor
MIC2040/2041 micrel m9999-012004 12 january 2004 /fault the /fault signal is an n-channel, open-drain mosfet output. an external pull-up resistor tied to a maximum 6v rail is required for the /fault pin. the /fault pin is asserted (active-low) when either an overcurrent or thermal shutdown condition occurs. during a hot insert of a pcb or when turning on into a highly capacitive load, the resulting high transient inrush current may exceed the current limit threshold of the MIC2040/41. in the case where an overcurrent condition occurs, /fault will assert only after the flag delay time has elapsed, typically 28ms. this ensures that /fault is as- serted only upon valid overcurrent conditions and that nui- sance error reporting is prevented. thermal shutdown for the MIC2040, thermal shutdown is employed to protect the device from damage should the die temperature exceed safe margins due to a short circuit or an excessive load. thermal shutdown shuts off the output mosfet and asserts the /fault output if the die temperature exceeds 140 c. the MIC2040 automatically resets its output and resumes supply- ing current to the load when the die temperature drops to 120 c. if the fault is still present, the MIC2040 will quickly reheat and shut down again. this process of turning on-off-on is called thermal cycling and will continue as long as the power switch is enabled while the fault or excessive load is present. depending on pcb layout (including thermal considerations such as heat sinking), package, and ambient temperature, it may take several hundred milliseconds from the incidence of the fault to the output mosfet being shut off. circuit breaker function (mic2041) the mic2041 is designed to shut off all power to the load when a fault condition occurs, just as a circuit breaker would do. a fault condition is deemed to be anytime the output current exceeds the current limit for more than the flag delay period, nominally 28ms. once the output shuts off, it remains off until either the fault load is removed from vout or the en input is cycled on-off-on. if the fault is still present after en has been cycled, the mic2041 will again shut off all power to the load after 28ms. once the fault has been removed, then normal operation will resume. open load detection the mic2041 will automatically reset its output when the fault load is cleared. this is accomplished by applying a small current to vout and watching for the voltage at vout to rise to within 200mv of vin. this current is supplied by an internal resistor connected to vin and is connected to vout when mic2041 latches off.
january 2004 13 m9999-012004 MIC2040/2041 micrel applications information input and output supply bypass filtering the need for input supply bypass is brought about due to several factors, most notably the input/output inductance along the power path, operating current and current limit, and output capacitance. a 0.1 f to 0.47 f bypass capacitor positioned very close to the vin pin to gnd of the device is strongly recommended to filter high frequency oscillations due to inductance. also, a sufficient bypass capacitor posi- tioned close to the input source to the switch is strongly advised in order to suppress supply transient spikes and to limit input voltage droop. inrush current increases with larger output capacitance, thus the minimum value of this capacitor will require experimental determination for the intended appli- cation and design. a good starting point is a capacitor between 4.7 f to 15 f. without these bypass capacitors, an extreme overload condition such as a short circuit, or a large capacitive load, may cause either the input supply to exceed the maximum rating of 6v and possibly cause damage to the internal control circuitry or allow the input supply to droop and fall out of regulation and/or below the minimum operating voltage of the device. output capacitance when the MIC2040 die exceeds the overtemperature thresh- old of approximately 140 c, the device can enter into a thermal shutdown mode if the die temperature falls below 120 c and then rises above 140 c in a continuous cycle. with the v out and /fault outputs cycling on and off, the MIC2040 will reset the /fault while in an overtemperature fault condition if the output voltage is allowed to swing below ground. the inductance present at the output must be neu- tralized by capacitance in order to ensure that the output does not fall below ground. in order to counter the board parasitic inductance and the inductance of relatively short-length (<1 ft., 16 - 20 gauge wire), a minimum output capacitance of 22 f is strongly recommended and should be placed close to the v out pin of the MIC2040. for applications that use more than a foot of cable, an additional 10 f/ft. is recom- mended. reverse current block the MIC2040/41 provides reverse current flow block through the output mosfet if the voltage at vout is greater than vin when the device is disabled. the vbias supply has a limited reverse current flow if the voltage at vout is pulled above vbias when the device is disabled. the reverse current for vbias can be completely blocked by inserting a schottky diode from the vbias pin (cathode) to the supply (anode). however, the minimum voltage of 1.6v must be supplied to vbias after accounting for the voltage drop across the diode. uvlo threshold setting with low input voltages when the switching voltage is below 1.6v, the device? standard uvlo threshold (1.45v nominal) will hinder the output mosfet in switching vin to vout. in this case, the use of the uvloin pin is required to override the standard uvlo threshold and set a new, lower threshold for the lower input operating voltages. an external resistive divider net- work connected at the uvloin pin is used to set the new threshold. due to the ratio of the internal components, the total series resistance of the external resistive divider should not exceed 200k ? . the circuit shown in figure 4 illustrates an application that switches 0.8v while the device is powered from a separate 2.5v power supply. the uvlo threshold is set by the following equation. v 0.23v 1 r2 r3 uvth =+ ? ? ? ? ? ? f to 1.0 f capacitor from uvloin to gnd may be used as a glitch filter in order to avoid nuisance tripping of the uvlo threshold. if the uvloin pin is not in use, this pin should be left open (floating). the use of a pull-down resistor to ground will offset the ratio of the internal resistive divider to this pin resulting in a shift in the uvlo threshold. to bypass (disable) uvlo, connect the uvloin pin directly to the vin pin of the MIC2040/41. 7,9 8 1 3 5 8,10 2 r set 220 ? c1 0.1 f 10 MIC2040-1bm vbias vin en /fault uvloin vout ilim gnd r1 47k ? r4 75k ? 1% r5 36.5k ? 1% c load 22 f v out 0.8v @1.25a r6 47k ? digital output signal c3 10 f c2 0.1 f v in 0.8v v dd 2.5v r2 95.3k ? 1% r3 59k ? 1% note: both v in pins (7, 9) must be externally tied together. both v out pins (8, 10) must be externally tied together. undervoltage lockout = 0.6v. figure 4. lower uvlo setting
MIC2040/2041 micrel m9999-012004 14 january 2004 power dissipation power dissipation depends on several factors such as the load, pcb layout, ambient temperature, and package type. the following equations can be used to calculate power dissipation and die temperature. calculation of power dissipation can be accomplished by the following equation: p d = r ds(on) (i out ) 2 (4) to relate this to junction temperature, the following equation can be used: t j = p d r (j-a) + t a (5) where t j = junction temperature, t a = ambient temperature and r (j-a) is the thermal resistance of the package. printed circuit board hot-plug the MIC2040/41 are ideal inrush current limiting power switches suitable for hot plug applications. due to the inte- grated charge pump, the MIC2040/41 present a high imped- ance when in the off state and the device slowly becomes a low impedance as it turns on. this effectively isolates power supplies from highly capacitive loads by reducing inrush current during hot plug events. this same feature also can be used for soft-start requirements. bus-powered hub (usb) figure 5 illustrates a bus-powered hub application where the MIC2040 provides ganged power switching to multiple down- stream ports. a low-cost mic5203 (sot-143) or mic5207 (to-92) 3.3v low-dropout (ldo) regulator provides power from the bus to the usb controller. pcb layout recommendations the MIC2040 and mic2041 have very low on-resistance, typically 50m ? , and the switches can provide up to 1.5a of continuous output current. under maximum load, the power consumed by the devices may cause the devices to heat up considerably. the following list contains some useful sug- gestions for pcb layout design of the MIC2040/41 in order to prevent the die from overheating under normal operating conditions. 7, 9 6 1 2 5 8,10 3 r set 220 ? note: bothv in pins (7, 9) must be externally tied together. bothv out pins (8, 10) must be externally tied together. i limit = 1.5a. c2 0.1 f 3.3v usb controller mic5203-3.3 on/off oc in d+ d- gnd 4 MIC2040-1bm vbias vin en /fault ilim vout uvloin gnd ldo regulator r2 20k ? r1 20k ? c load 10 f (open) v out 5v@ 1a c1 0.1 f c load 10 f c load 10 f downstream port (100ma max.) downstream port (100ma max.) downstream port (100ma max.) gnd out in c4 1 f c3 4.7 f vbus d+ d- gnd figure 5. multi-port bus-powered hub 1. supply additional copper area under the device to remove heat away from the ic. see ?pplication hint 17 for a general guideline in calculating the suggested area. 2. provide additional pad area on the corner pins of the MIC2040/41 ic for heat distribution. 3. tie the common power pins (v in = pins 7 and 9 and v out = pins 8 and 10) together in a manner such that the traces entering and leaving the device have a uniform width sufficient for the application? current requirements plus added margin (25% minimum recommended). ex: for 1a maximum current, design traces for 1.25a capability. 4. for pcb trace width calculations, there are numerous calculator programs available on the internet and elsewhere. as a general rule of thumb, 15-20 mils for every 1a of current when using 1oz. copper. however, the trace width calculators often take into account maximum temperature increase constraints, as well as layer arrangement, in determining the pcb trace widths.
january 2004 15 m9999-012004 MIC2040/2041 micrel package information i rev. 00 10-pin msop (mm) micrel, inc. 1849 fortune drive san jose, ca 95131 usa tel + 1 (408) 944-0800 fax + 1 (408) 944-0970 web http://www.micrel.com the information furnished by micrel in this datasheet is believed to be accurate and reliable. however, no responsibility is as sumed by micrel for its use. micrel reserves the right to change circuitry and specifications at any time without notification to the customer. micrel products are not designed or authorized for use as components in life support appliances, devices or systems where malfu nction of a product can reasonably be expected to result in personal injury. life support devices or systems are devices or systems that (a) are intend ed for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant inj ury to the user. a purchaser? use or sale of micrel products for use in life support appliances, devices or systems is at purchaser? own risk and purchaser agrees to fully indemnify micrel for any damages resulting from such use or sale. ?2003 micrel, incorporated.

▲Up To Search▲

Price & Availability of MIC2040

	To Download MIC2040 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .