View TH-G30_6262602.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

TH-G30 consists of xv-thg30 and sp-thg50c/f/w dvd digital cinema system instructions l vt1880-004a [b] ht993sj_eng tuning tuning http://www..net/ datasheet pdf - http://www..net/
g-1 this lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. the exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. w arning: do not install this equipment in a confined space such as a book case or similar unit. caution: do not block any ventilation openings. install in accordance with the manufacturer's instructions. slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating. the openings should be never be blocked by placing the product on a bed, sofa, rug or other similar surface. this product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instruction have been adhered to. caution: class1 laser product this product employs a laser system. to ensure proper use of this product, please read this owners manual carefully and retain it for future reference. should the unit require maintenance, contact an authorized service center. use of controls, adjustments or the performance of procedures other than those specified herein may result in hazardous radiation exposure. to prevent direct exposure to laser beam, do not try to open the enclosure. visible laser radiation when open. do not stare into beam. caution: ?do not block the ventilation openings or holes. (if the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get out.) ?do not place any naked flame sources, such as lighted candles, on the apparatus. ?when discarding batteries, environmental problems must be considered and local rules or laws governing the disposal of these batteries must be followed strictly. ?do not expose this apparatus to rain, moisture, dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. ?battery shall not be exposed to excessive heat such as sunshine, fire or the like. ?the standby/on button does not completely shut off mains power from the unit, but switches operating current on and off. caution risk of electric shock do not open caution: to reduce the risk of electric shock do not remove cover (or back) no user-serviceable parts inside refer servicing to qualified service personnel. w arning: to prevent fire or electric shock hazard, do not expose this product to rain or moisture. class 1 laser product klasse 1 laser produkt luokan 1 laser laite klass 1 laser apparat classe 1 produit laser http://www..net/ datasheet pdf - http://www..net/
g-2 caution: the apparatus should not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, should be placed on the apparatus. caution concerning the power cord most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. check the specification page of this owner's manual to be certain. do not overload wall outlets. overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. any of these conditions could result in electric shock or fire. periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. to disconnect power from the mains, pull out the mains cord plug. when installing the product, ensure that the plug is easily accessible. disposal of your old appliance 1. when this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the european directive 2002/96/ec. 2. all electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. 3. the correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health. 4. for more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product. dear customer, this apparatus is in conformance with the valid european directives and standards regarding electromagnetic compatibility and electrical safety. european representative of victor company of japan, limited is: jvc technical services europe gmbh postfach 10 05 04 61145 friedberg germany http://www..net/ datasheet pdf - http://www..net/
g-3 some do?s and don?ts on the safe use of equipment this equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured. do read the operating instructions before you attempt to use the equipment. do ensure that all electrical connections (including the mains plug, extension leads and interconnections betweenpieces of equipment) are properly made and in accordance with the manufacturer?s instructions. switch off and withdraw the mains plug when making or changing connections. do consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment. do be careful with glass panels or doors on equipment. don?t continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any way-switch off, withdraw the mains plug and consult your dealer. don?t remove any fixed cover as this may expose dangerous voltages. don?t leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended operation or has a standby mode. switch off using the switch on the equipment and make sure that your family knows how to do this. special arrangements may need to be made for infirm or handicapped people. don?t use equipment such as personal stereos or radios so that you are distracted from the requirements of road safety. it is illegal to watch television whilst driving. don?t listen to headphones at high volume, as such use can permanently damage your hearing. don?t obstruct the ventilation of the equipment, for example with curtains or soft furnishings. overheating will cause damage and shorten the life of the equipment. don?t use makeshift stands and never fix legs with wood screws-to ensure complete safety always fit the manufacturer?s approved stand or legs with the fixings provided according to the instructions. don?t allow electrical equipment to be exposed to rain or moisture. above all... - never let anyone especially children push anything into holes, slots or any other opening in the case-this could result in a fatal electrical shock; - never guess or take chances with electrical equipment of any kind-it is better to be safe than sorry! safety precautions important: connection to the mains supply in the united kingdom. do not cut off the mains plug from this equipment. if the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain a proper safety approved extension lead/adapter or consult your dealer. in the unlikely event of the plug fuse failing be sure to replace the fuse only with an identical approved type, as originally fitted, and to replace the fuse cover. if the fuse fails again consult your nearest jvc dealer. if nonetheless the mains plug is cut off remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply. if this product is not supplied fitted with a mains plug then follow the instructions given below: do not make any connection to the larger terminal coded e or green. the wires in the mains lead are coloured in accordance with the following code: if these colours do not correspond with the terminal identifications of your plug, connect as follows: blue wire to terminal coded n (neutral) or coloured black. brown wire to terminal coded l (live) or coloured red. if in doubt - consult a competent electrician. blue to n (neutral) or black brown to l (live) or red http://www..net/ datasheet pdf - http://www..net/
1 introduction . . . . . . . . . . . . . . . . . . .2-5 about the symbol display . . . . . . . . . . . . . .2 symbol used in this manual . . . . . . . . . . . . . . .2 screen saver . . . . . . . . . . . . . . . . . . . . . . . . . . .2 notes on discs . . . . . . . . . . . . . . . . . . . . . . . . . .2 handling discs . . . . . . . . . . . . . . . . . . . . . . . .2 storing discs . . . . . . . . . . . . . . . . . . . . . . . . .2 cleaning discs . . . . . . . . . . . . . . . . . . . . . . . .2 t ypes of playable discs . . . . . . . . . . . . . . . . . .3 regional code . . . . . . . . . . . . . . . . . . . . . . . . . .3 front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 remote control . . . . . . . . . . . . . . . . . . . . . . . . .5 remote control operation . . . . . . . . . . . . . . .5 remote control battery installation . . . . . . . .5 installation and setup . . . . . . . . .6-14 tv connection . . . . . . . . . . . . . . . . . . . . . . . . . .6 v ideo connection . . . . . . . . . . . . . . . . . . . . . .6 component video connection . . . . . . . . . . . .6 scart connection . . . . . . . . . . . . . . . . . . . . .6 antenna connection . . . . . . . . . . . . . . . . . . . . .6 optional equipment connection . . . . . . . . . . .7 aux in connection (a) . . . . . . . . . . . . . . . . . .7 optical in connection (o) . . . . . . . . . . . . . .7 audio in connection (d) . . . . . . . . . . . . . . . .7 usb connection (u) . . . . . . . . . . . . . . . . . . . .7 hdmi connection . . . . . . . . . . . . . . . . . . . . . . . .8 about hdmi . . . . . . . . . . . . . . . . . . . . . . . . . .8 resolution setting . . . . . . . . . . . . . . . . . . . . . .8 a vailable resolution according to connection .8 speaker system connection . . . . . . . . . . . . . .9 displaying disc information on-screen . . . . .10 initial settings . . . . . . . . . . . . . . . . . . . . . . .10-14 osd initial language settings . . . . . . . . . .10 general operation . . . . . . . . . . . . . . . . . .11 language . . . . . . . . . . . . . . . . . . . . . . . . .11 osd . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 disc audio / subtitle / menu . . . . . . . . .11 display . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 tv aspect . . . . . . . . . . . . . . . . . . . . . . .11 display mode . . . . . . . . . . . . . . . . . . . . .11 tv output select . . . . . . . . . . . . . . . . . .11 ? ideo resolution . . . . . . . . . . . . . . . . . .12 audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 dynamic range control (drc) . . . . . . .12 ? ocal . . . . . . . . . . . . . . . . . . . . . . . . . . .12 hd av sync . . . . . . . . . . . . . . . . . . . . .12 5.1 speaker setup . . . . . . . . . . . . . . . . .13 lock (parental control) . . . . . . . . . .13 initial setting the area code . . . . . . . . .13 rating . . . . . . . . . . . . . . . . . . . . . . . . . .14 password . . . . . . . . . . . . . . . . . . . . . . . .14 area code . . . . . . . . . . . . . . . . . . . . . . .14 others . . . . . . . . . . . . . . . . . . . . . . . . . . .14 pbc . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 divx(r) registration . . . . . . . . . . . . . . .14 operations . . . . . . . . . . . . . . . . .15-23 general features . . . . . . . . . . . . . . . . . . . . . . .15 additional features . . . . . . . . . . . . . . . . . . . . .16 playing an audio cd or mp3/wma file . . . . .17 programmed playback . . . . . . . . . . . . . . . . . .18 repeat programmed tracks . . . . . . . . . . . .18 erasing a track from program list . . . . . . .18 erasing the complete program list . . . . . . .18 v iewing a jpeg file . . . . . . . . . . . . . . . . . . . . .19 slide show . . . . . . . . . . . . . . . . . . . . . . . . . .19 still picture . . . . . . . . . . . . . . . . . . . . . . . . . .19 moving to another file . . . . . . . . . . . . . . . . . .19 rotating the picture . . . . . . . . . . . . . . . . . . .19 playing a divx movie file . . . . . . . . . . . . . . . .20 presetting the radio stations . . . . . . . . . . . . .21 to tune in a station with a weak signal . . . .21 to clear all the stored stations . . . . . . . . . .21 listening to the radio . . . . . . . . . . . . . . . . . . .21 to turn off the radio . . . . . . . . . . . . . . . . . . .21 to listen to non-preset radio stations . . . . .21 to select a preset radio station directly . . . .21 rds operation . . . . . . . . . . . . . . . . . . . . . . . . .22 sleep timer setting . . . . . . . . . . . . . . . . . . . . .23 dimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 muting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 setting the disc ejection lock . . . . . . . . . . . . .23 enjoying audio form an external source . . . .23 setting the surround mode . . . . . . . . . . . . . . .23 reference . . . . . . . . . . . . . . . . . . .24-27 language codes . . . . . . . . . . . . . . . . . . . . . . . .24 area codes . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 t roubleshooting . . . . . . . . . . . . . . . . . . . . . .25-26 specifications . . . . . . . . . . . . . . . . . . . . . . . . . . .27 contents http://www..net/ datasheet pdf - http://www..net/
2 to ensure proper use of this product, please read this owners manual carefully and retain it for future reference. this manual provides information on the operation and maintenance of your dvd player. should the unit require service, contact an authorized service location. about the symbol display ? ?may appear on your tv display during operation and indicates that the function explained in this owners manual is not available on that specific dvd video disc. symbol used in this manual note: indicates special notes and operating features. tip: indicates tips and hints for making the task easier. a section whose title has one of the following symbols is applicable only to the disc represented by the symbol. all discs and file listed below dvd and finalized dvdr/rw v ideo cds audio cds mp3 files wma files jpeg files divx files screen saver the screen saver activates when there is no operation made for approximately 5 minutes since a still picture was last displayed. to cancel the screen saver, push any key. notes on discs handling discs do not touch the playback side of the disc. hold the disc by the edges so that fingerprints do not get on the surface. never stick paper or tape on the disc. storing discs after playing, store the disc in its case. do not expose the disc to direct sunlight or sources of heat and never leave it in a parked car exposed to direct sunlight. cleaning discs fingerprints and dust on the disc can cause poor picture quality and sound distortion. before playing, clean the disc with a clean cloth. wipe the disc from the center out. do not use strong solvents such as alcohol, benzine, thinner, commercially available cleaners, or anti-static spray intended for older vinyl records. divx jpeg wma mp3 acd vcd dvd all introduction http://www..net/ datasheet pdf - http://www..net/
3 introduction t ypes of playable discs dvd (8 cm / 12 cm disc) v ideo cd (vcd) (8 cm / 12 cm disc) audio cd (8 cm / 12 cm disc) in addition, this unit can play a dvdr, dvdrw, svcd and cd-r or cd-rw that contains audio titles, mp3, wma, jpeg or divx files. notes: depending on the conditions of the recording equipment or the cd-r/rw (or dvdr/rw) disc itself, some cd-r/rw (or dvdr/rw) discs may not be played on the unit. do not use irregularly shaped cds (e.g., heart- shaped or octagonal) since they may result in malfunctions. this unit requires discs and recordings to meet certain technical standards in order to achieve optimal playback quality. pre-recorded dvds are automatically set to these standards. there are many different types of recordable disc formats (including cd-r containing mp3 or wma files) and these require certain pre-existing conditions (see above) to ensure compatible playback. customers should note that permission is required in order to download mp3 / wma files and music from the internet. our company has no right to grant such permission. permission should always be sought from the copyright owner. regional code this unit has a regional code printed on the rear of the unit. this unit can play only dvd discs labelled as the same as the rear of the unit or ?ll? notes on regional codes most dvd discs have a globe with one or more numbers in it clearly visible on the cover. this number must match your units regional code or the disc cannot play. if you try to play a dvd with a different regional code from your player, the message ?heck regional code?appears on the tv screen. notes on copyrights: it is forbidden by law to copy, broadcast, show, broadcast via cable, play in public, or rent copyrighted material without permission. this product features the copy protection function developed by macrovision. copy protection signals are recorded on some discs. when recording and playing the pictures of these discs picture noise will appear. this product incorporates copyright protection technology that is protected by method claims of certain u.s. patents and other intellectual property rights owned by macrovision corporation and other rights owners. the use of this copyright protection technology must be authorized by macrovision corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by macrovision corporation. reverse engineering or disassembly is prohibited. consumers should note that not all high definition television sets are fully compatible with this product and may cause artifacts to be displayed in the picture. in case of 525 progressive scan picture problems, it is recommended that the user switch the connection to the ?tandard definition output. if there are questions regarding our tv set compatibility with this model 525p dvd player, please contact our customer service center. http://www..net/ datasheet pdf - http://www..net/
4 front panel a 1 1 / / ' ' (standby/on) switches the unit on and off. b disc tray insert a disc here. c usb port connect to a usb port of a memory device (usb memory etc.) d audio in the audio in port means you can connect a audio device to play through the surround sound speakers. e z (open/close) opens or closes the disc tray. f b (play) starts playback. source press and hold down this button about 3 seconds, then press repeatedly to select other function g x x (pause) pause playback. fm mode this will change the tuner from stereo to mono and usually improve the reception. h x (stop) stops playback. i . (skip) returns to the beginning of current chapter or track or go to the previous chapter or track. (scan) during playback, press and hold this button repeatedly to select the required scan speed. - tuning t unes in the desired radio station. j > (skip) go to the next chapter or track. (scan) during playback, press and hold this button repeatedly to select the required scan speed. + tuning t unes in the desired radio station. k volume controller abcd e fghijk http://www..net/ datasheet pdf - http://www..net/
5 introduction remote control remote control operation point the remote control at the remote sensor and press the buttons. cautions: do not mix old and new batteries and never mix different types of batteries such as standard, alkaline, etc. do not put the batteries in the place where young children can reach. battery shall not be exposed to excessive heat such as sunshine, fire or the like. when discarding batteries, environmental problems must be considered and local rules or laws governing the disposal of these batteries must be followed strictly. remote control battery installation detach the battery cover on the rear of the remote control, and insert two batteries (size aaa) with 3 and # aligned correctly. audio ( 1 1 / / ' ' ) switches the unit on and off. function selects the function (dvd/cd , fm, am) input changes the input source ( aux, aux opt, audio in, usb, tv-audio) sleep sets the system to turn off automatically at a specified time. dimmer changes brightness of the display window on the front panel during in power-on status. return press to move back wards in the menu. to p menu if the current dvd title has a menu, the title menu appears on the screen. otherwise, the disc menu may appear. menu accesses the menu on a dvd disc. set up accesses or removes setup menu. display accesses on-screen display. b / b / v / v (left/right/up/down) selects an option in the menu. enter acknowledges the menu selection. preset ( # # / 3 3 ) selects program of radio. tuning. ( # # / 3 3 ) t unes in the desired radio station. 0-9 numerical buttons: selects numbered options in a menu. surround selects the surround mode. subtitle selects a subtitle language (dvd). prog./memo. accesses or removes program menu. enter a radio stations frequency into the tuner. repeat repeats chapter, track, title, all clear removes a track number on the program list. scan/slow( bb / bb ) searches backward or forward. reverse/ forward slow playback. skip ( . . / > > ) stop ( x x ) play ( b ) fm mode this will change the tuner from stereo to mono and usually improve the reception. p ause/step ( x x ) volume (-/+) adjusts speaker volume. muting rds display v iews the various displays of the rds options. pty search to start a search for a specific pty type. tuning tuning http://www..net/ datasheet pdf - http://www..net/
6 tv connection make one of the following connections, depending on the capabilities of your existing equipment. tips: depending on your tv and other equipment you wish to connect, there are various ways you could connect the dvd/cd receiver . use one of the connections described below. please refer to the manuals of your tv, vcr, stereo system or other devices as necessary to make the best connections. caution: make sure the dvd/cd receiver is connected directly to the tv. select the correct av input on your tv. do not connect your dvd/cd receiver to tv via your vcr. the dvd image could be distorted by the copy protection system. do not connect your dvd/cd receiver to tv with cables more than two kinds. in some case, picture distortion may occur during playback. v ideo connection connect the monitor out jack from the dvd/cd receiver to the video in jack on the tv using the video cable (v) . component video connection connect the component video out jacks from the dvd/cd receiver to the corresponding jacks on the tv using an y p b p r cable (c) . if your television is a high-definition or ?igital ready?television, you may take advantage of the dvd/cd receiver ? progressive scan output for the highest video resolution. if your tv does not accept your resolution setting, abnormal picture appears on the screen. please read owners manual for tv then set the resolution that your tv can accept. scart connection connect the euro av output (to tv) socket on the dvd/cd receiver to the corresponding jacks on the tv using the scart cable (t) . notes: the hdmi mode must be set to off for video out and component video connections. a picture via scart input is not supported. antenna connection connect the supplied fm/am antenna for listening to the radio. connect the am loop antenna to the am antenna connector. connect the fm wire antenna to the fm antenna connector. notes: to prevent noise pickup, keep the am loop antenna away from the dvd/cd receiver and other components. be sure to fully extend the fm wire antenna. after connecting the fm wire antenna, keep it as horizontal as possible. installation and setup rear of dvd/cd receiver rear of tv vc (supplied) (not supplied) t (not supplied) fm wire antenna (supplied) am loop antenna (supplied) y component video / progressive scan input l video input scart input http://www..net/ datasheet pdf - http://www..net/
7 installation and setup optional equipment connection aux in connection (a) connect a output of auxiliary device to the aux audio input (l/r) connector. optical in connection (o) connect an optical output of dvd player (or digital device etc) to the optical in connector. audio in connection (d) connect a output of portable device (mp3 or pmp etc) to the audio input connector. usb connection (u) connect the usb port of usb memory (or mp3 player, etc.) to the usb port on the front of the unit. if you want to opterate functions, see the operation section. removing the usb device from the unit 1. choose a different function mode or press stop ( x ) twice in a row. 2. remove the usb device from the unit. notes: don? extract the usb device while operating. music files (mp3/wma), image files (jpeg) and video files can be played. this unit can not use a usb hub. recommended memory cards. compact flash card (cfc), micro drive (md), smart media card (smc), memory stick (ms), secure digital card (sd), multi media card (mmc), memory stick pro (ms-pro) - compatible with : fat16, fat32 - only use the memory cards recommended. devices which require additional program installation when you have connected the unit to a computer are not supported. in case of a usb hdd, make sure to connect an auxiliary power cord to the usb hdd for proper operation. up to four primary partitions of a drive are supported. if there is an extension partition, it will not be supported. if the drive of usb device is two or more, a drive folder is displayed on the screen. if you want to move to the initial menu after you select a folder, press return. digital cameras and mobile phones are not supported. rear of dvd/cd receiver o a auxiliary device dvd player (or digital device, etc) to audio out (l/r) to av in audio (l/r) d portable device to audio out to audio in (not supplied) (not supplied) (not supplied) u usb memory, mp3 player (or memory card reader, etc.) video out in audio (l) audio (r) optical out http://www..net/ datasheet pdf - http://www..net/
8 hdmi connection about hdmi hdmi (high definition multimedia interface) supports both video and audio on a single digital connection for an easy all- digital output to an hdmi or di-equipped tv. connection to an hdmi tv requires an hdmi cable while connection to a dvi-equipped tv requires a dvi adapter besides a hdmi cable. hdmi has the capability to support standard, enhanced, or high-definition video plus standard to multi-channel surround-sound audio, hdmi features include uncompressed digital video, a bandwidth of up to 5 gigabytes per second, one connector (instead of several cables and connector), and communication between the av source and av devices such as dtvs. hdmi, the hdmi logo and high-definition multimedia interface are trademarks or registered trademarks of hdmi licensing llc. if you have a hdmi tv or monitor, you can connect it to this dvd/cd receiver using a hdmi cable. 1. connect the hdmi out jack on the dvd/cd receiver to the hdmi jack on a hdmi compatible tv or monitor (h). 2. set the tvs source to hdmi (refer to owners manual for tv). notes: the arrow on the cable connector body should face down for correct alignment with the connector on the dvd/cd receiver. if there is noise or there are lines on the screen, please check the hdmi cable. not all hdcp-compatible dvi devices will work with this dvd/cd receiver. if tv does not support hdcp, snow noise appears on the screen, or picture may be vibrated. if you play the multi-channel software such as dolby digital or dts, only pcm signals can be output via an hdmi cable. resolution setting y ou can change the resolution for component video and hdmi output. to change the resolution using setup menu to select the desired resolution - auto, 480i (or 576i), 480p (or 576p), 720p, 1080i, 1080p. a vailable resolution according to connection hdmi out - auto, 1080p, 1080i, 720p and 480p (or 576p) component video out - 480p (or 576p) and 480i (or 576i) video out - 480i (or 576i) note: if your tv does not accept your resolution setting, abnormal picture appears on the screen. please read owners manual for tv, and then set the resolution that your tv can accept. h hdmi compatible tv rear of dvd/cd receiver hdmi http://www..net/ datasheet pdf - http://www..net/
9 installation and setup speaker system connection connect the speakers using the supplied speaker cables. to obtain the best possible surround sound, adjust the speaker parameters (volume, distance, etc.). notes: be sure to match the speaker cable to the appropriate terminal on the components: + to + and ?to ? if the cables are reversed, the sound will be distorted and will lack base. if you use front speakers with low maximum input rating, adjust the volume carefully to avoid excessive output on the speakers. caution: the left and right speakers can be installed on a wall. when installing the speakers on a wall, be sure to have the speakers installed by qualified personnel. do not install the speakers on the wall by yourself to avoid unexpected damage from them falling off the wall due to incorrect installation or weakness in wall structure. care must be taken in selecting a location for speaker installation on a wall. injury to personnel or damage to devices may result if the installed speakers interfere with daily activities. front speaker (right) front speaker (left) center speaker rear speaker (right surround) subwoofer rear speaker (left surround) http://www..net/ datasheet pdf - http://www..net/
10 displaying disc information on-screen y ou can display various information about the disc loaded on-screen. 1. press display to show various playback information. the displayed items differ depending on the disc type or playing status. 2. you can select an item by pressing v / v and change or select the setting by pressing b / b . t itle ?current title number/ total number of titles. chapter ?current chapter number/total number of chapters. t ime ?elapsed playing time. audio ?selected audio language or channel. subtitle ?selected subtitle. angle ?selected angle/total number of angles. sound ?selected sound mode. note: if any button is not pressed for a few seconds, the on- screen display disappears. initial settings by using the setup menu, you can make various adjustments to items such as picture and sound. y ou can also set a language for the subtitles and the setup menu, among other things. for details on each setup menu item, see pages 10 to 14. osd initial language settings: when the power is turned on for the first time, the unit need to set the menu language. follow the descriptions below after the display connections. after osd initial language setting, to set area code (see page 13) 1. press power to turn the unit on. the language setup menu will appear on the screen. 2. use b / b / v / v to select a language then press enter. the confirm menu will appear. 3. use b / b to select the [enter] then press enter to finish the language setup. to display and exit the menu: press setup to display the menu. a second press of setup will take you back to initial screen. to go to the next level: press b on the remote control. to go back to the previous level: press b on the remote control. http://www..net/ datasheet pdf - http://www..net/
11 installation and setup general operation 1. press setup. the setup menu appears. 2. use v / v to select the desired option then press b to move to the second level. the screen shows the current setting for the selected item, as well as alternate setting(s). 3. use v / v to select the second desired option and then press b to move to the third level. 4. use v / v to select the desired setting then press enter to confirm your selection. some items require additional steps. 5. press setup or play ( n ) to exit the setup menu. language osd select a language for the setup menu and then on- screen display. disc audio / subtitle / menu select the language you prefer for the audio track (disc audio), subtitles, and the disc menu. original refers to the original language in which the disc was recorded. other to select another language, press numeric buttons and then enter to enter the corresponding 4-digit number according to the language code list on the page 24. if you enter the wrong language code, press clear. display tv aspect 4:3 ? select when a standard 4:3 tv is connected. 16:9 ? select when a 16:9 wide tv is connected. display mode the display mode setting works only when the tv aspect mode is set to 4:3. letterbox ? displays a wide picture with bands on the upper and lower portions of the screen. panscan ? automatically displays the wide picture on the entire screen and cuts off the portions that do not fit. (if the disc/file is not compatible with pan scan, the picture is displayed at letterbox ratio.) tv output select select an option according to the tv connection type. ypbpr - when your tv is connected with the component/progressive scan jacks on the unit. rgb - when your tv is connected with the scart jack. note: s-video signal thruogh the scart jack is not supported. http://www..net/ datasheet pdf - http://www..net/
12 vi deo resolution use vv to select the desired resolution then press enter to confirm your selection. full hd up-scaling convert sd(standard definition) resolution into hd (high definition) resolution. the number in 480p (or 576p), 720p, 1080p and 1080i indicates the number of lines of video. the ? and ??indicate interlaced and progressive scan, respectively. auto - if you hdmi jack is connected for tvs providing display information (edid), automatically selects the resolution best suited to the connected tv (1080p, 1080i, 720p or 480p (or 576p)). (only for hdmi connection) 1080p - outputs 1080 lines of progressive video. (only for hdmi connection) 1080i - outputs 1080 lines of interlaced video. 720p - outputs 720 lines of progressive video. 480p (or 576p) - outputs 480 (or 576) lines progressive video. 480i (or 576i) - outputs 480 (or 576) lines of interlaced video. notes on video resolution only resolutions supported by the tv are available. depending on your tv, certain hdmi output resolutions may not work. if your tv does not accept your resolution setting, an abnormal picture appears on the screen. please read tvs owners manual then set the resolution that your tv can accept. if the hdmi jack is connected for tvs providing display information (edid), you can not select resolutions that the tv does not accept. audio each dvd disc has a variety of audio output options. set the players audio options according to the type of audio system you use. dynamic range control (drc) with the dvd* 1 format, you can hear a programs soundtrack in the most accurate and realistic presentation, thanks to digital audio technology. however, you may wish to compress the dynamic range of the audio output (the difference between the loudest sounds and the quietest ones). then, you may listen to a movie at a lower volume without losing clarity of sound. set drc to on for this effect. *1: dolby digital only v ocal set vocal to on only when a multi-channel karaoke dvd is playing. the karaoke channels on the disc will mix into normal stereo sound. hd av sync when using digital tv. sometimes av signal could not be transmitted simultaneously because of later transmission of video signal compared to audio signal. because it takes some time to convert analogue video signal to digital one in the digital tv. and it means that you may not enjoy picture on the screen and sound from speaker at the same time even though it is one scene. in the hd av sync menu, you could adjust delay time to audio signal for simultaneous av signal transmission delay time could be set up with 10msec unit. (0 ~ 300ms) delay time is different according to each tv brand. so you need to adjust optimal delay time complying with your tv. http://www..net/ datasheet pdf - http://www..net/
13 installation and setup 5.1 speaker setup make the following settings for the built-in 5.1 channel surround decoder. 1. press enter, and the 5.1 speaker setup menu appears. 2. use b / b to select the desired speaker. 3. adjust options using v / v / b / b buttons. 4. press enter to confirm your selection. returns to the previous menu. speaker selection select a speaker that you want to adjust. [front speaker (front l), front speaker (front r), center speaker (center), subwoofer (subwoofer), rear speaker (rear l), rear speaker (rear r)] note: certain speaker settings are prohibited by the dolby digital licensing agreement. size since the speaker settings are fixed, you cannot change the settings. vol ume press b / b to adjust the output level of the selected speaker. (-5db ~ 5db) distance after you connected speakers to your dvd receiver, set the distance between the speakers and your listening point if the distance of center or rear speakers is bigger than the distance of front speakers. this allows the sound from each speaker to reach the listener at the same time. press b / b to adjust the distance of the selected speaker. this distance is equivalent to a difference of the distance between center or rear speaker and front speakers. note: y ou can? adjust front/woofer speakers. the distance of front speaker is considered to be the standard. t est press b / b to test the signals of each speaker. adjust the volume to match the volume of test signals memorized in the system. front left (front l) center front right (front r) rear right (rear r) rear left (rear l) subwoofer lock (parental control) initial setting the area code: see the area codes on page 24. 1. select the lock menu and then press b . 2. to access the lock options, you must input the password you have created. input a password and press enter. enter it again and press enter to verify. if you make a mistake before pressing enter, press clear. 3. select the first character using v / v buttons. 4. press b and select the second character using v / v buttons. 5. press enter to confirm your area code selection. http://www..net/ datasheet pdf - http://www..net/
14 rating blocks playback of rated dvds based on their contents. not all discs are rated. 1. select ?ating?on the lock menu then press b . 2. input a password and press enter. 3. select a rating from 1 to 8 using the v / v buttons. rating 1-8: rating one (1) has the most restrictions and rating eight (8) is the least restrictive. unlock: if you select unlock, parental control is not active and the disc plays in full. 4. press enter to confirm your rating selection, then press setup to exit the menu. password y ou can enter or change password. 1. select password on the lock menu and then press b . 2. follow the step 2 as shown above (rating). to change the password, press enter when the ?hange?option is highlighted. input a password and press enter. enter it again and press enter to verify. 3. press setup to exit the menu. if you forget your password if you forget your password, you can clear it using the following steps: 1. press setup to display the setup menu. 2. input the 6-digit number ?10499?and press enter. the password is cleared. area code enter the code of the area whose standards were used to rate the dvd video disc, based on the list on page 24. 1. select ?rea code?on the lock menu then press b . 2. follow the step 2 as shown previous paragraph (rating). 3. select the first character using v / v buttons. 4. press b and select the second character using v / v buttons. 5. press enter to confirm your area code selection. others pbc set playback control (pbc) to on or off. on: v ideo cds with pbc are played according to the pbc. off: v ideo cds with pbc are played in the same way as audio cds. divx(r) registration we provide you the divx vod (video on demand) registration code that allows you to rent and purchase videos based on the divx vod service. for more information, visit www.divx.com/vod. 1. select ?ivx(r) registration?option and then press b . 2. press enter while ?elect?is selected and the registration code will appear. use the registration code to purchase or rent the videos from divx vod service at www.divx.com/vod. follow the instructions and download the video onto a disc for playback on this unit. 3. press enter to exit. note: all the downloaded videos from divx vod can only be played back on this unit. http://www..net/ datasheet pdf - http://www..net/
15 operation operation general features buttons operations z (open / close) opens or closes the disc tray. x (pause) during playback, press x to pause playback. press x repeatedly to play frame-by-frame. skip ( . / > ) during playback, press skip ( . or > ) to go to the next chapter/track or to return to the beginning of the current chapter/track. press skip . twice briefly to step back to the previous chapter/track. scan ( m / m ) during playback, press scan ( m or m ) repeatedly to select the required scan speed. dvd : bb , bbb , bbbb , bbbbb , bbbbbb or bb , bbb , bbbb , bbbbb , bbbbbb divx disc, video cd : bb , bbb , bbbb , bbbbb or bb , bbb , bbbb , bbbbb wma/mp3, audio cd : m (x2, x4, x8) or m (x2, x4, x8) repeat during playback, press repeat repeatedly to select a desired repeat mode. dvd video discs: chapter/title/off v ideo cd, audio cd, divx/mp3/wma discs: track/all/off to p menu if the current dvd title has a menu, the title menu appears on the screen. otherwise, the disc menu may appears. menu the disc menu appears on the screen. (subtitle) during playback, press subtitle repeatedly to select a desired subtitle language. slow in the pause mode, press scan ( m or m ) to select the required speed. dvd : t (1/2, 1/4, 1/8, 1/16) or t (1/2, 1/4, 1/8, 1/16) v ideo cd : t (1/2, 1/4, 1/8, 1/16) discs vcd dvd divx dvd dvd dvd all wma mp3 acd divx vcd dvd all divx vcd dvd all all http://www..net/ datasheet pdf - http://www..net/
16 additional features t ime search to start playing at any chosen time on the disc: 1. press display during playback. 2. press v / v to select the time clock icon and ?-:--:--?appears. 3. input the required start time in hours, minutes, and seconds from left to right. if you enter the wrong numbers, press clear to remove the numbers you entered. then input the correct numbers. 4. press enter to confirm. playback starts from the selected time. 1.5 times speed playback y ou can play at 1.5 times speed. the 1.5 speed allows you to watch the pictures and listen to the sound quicker than playing at a normal speed on the disc. 1. during playback, press play( b ) to play at 1.5 times speed. b x1.5?appears on the screen. 2. press play( b ) again to exit. screen saver the screen saver appears when you leave the unit in stop mode for about five minutes. to cancel the screen saver, press any button and then operate the unit. last scene memory this receiver memorizes the last scene from the last disc that is viewed. the last scene remains in the memory even if you remove the disc from the receiver or switch off the receiver. if you load a disc that has the scene memorized, the scene is automatically recalled. note: this receiver does not memorize the scene of a disc if you switch off the receiver before commencing to play the disc. mixed disc or usb flash drive ?mp3/wma and jpeg when playing a disc or usb flash drive contained with mp3/wma and jpeg files together, you can select which menu of files you would like to play by pressing to p menu. system select y ou must select the an appropriate system mode for your tv system. if no disc appears in the display window, press and hold pause/step ( x ) remote control for more than 5 seconds to be able to select a system (pal, ntsc). when the selected system is not compatible with the system of your tv, normal colour picture may not be displayed. ntsc: select when dvd/cd receiver is connected with ntsc-tv. p al: select when dvd/cd receiver is connected with pal-tv. dvd wma mp3 acd vcd dvd dvd http://www..net/ datasheet pdf - http://www..net/
17 operation playing an audio cd or mp3/wma file this unit can play audio cds or mp3/wma files. mp3/ wma/ audio cd once you insert an mp3/wma files recording media or audio cd a menu appears on the tv screen. press v / v to select a track/file and then press play or enter, and playback starts. you can use variable playback functions. refer to the page 15. id3 tag when playing a file containing information such as track titles, you can see the information by pressing display. (song, artist, album, genre, comment) tips: press menu to move to the next page. mp3 / wma disc compatibility with this player is limited as follows: sampling frequency: within 32 - 48 khz (mp3), within 24 - 48khz (wma) bit rate: within 32 - 320kbps (mp3), 40 - 192kbps (wma) the dvd/cd receiver cannot read an mp3/wma file that has a file extension other than ?mp3?/ ?wma? cd-r physical format should be iso 9660 if you record mp3 / wma files using software that cannot create a file system (eg. direct-cd) it is impossible to playback mp3 / wma files.we recommend that you use easy-cd creator, which creates an iso 9660 file system. file names should have a maximum of 8 letters and must incorporate an .mp3 or .wma extension. they should not contain special letters such as / ? * : < > l etc. the total number of files on the disc should be less than 999. this dvd/cd receiver requires discs and recordings to meet certain technical standards in order to achieve optimal playback quality. pre-recorded dvds are automatically set to these standards. there are many different types of recordable disc formats (including cd-r containing mp3 or wma files) and these require certain pre-existing conditions (see above) to ensure compatible playback. customers should note that permission is required in order to download mp3 / wma files and music from the internet. our company has no right to grant such permission. permission should always be sought from the copyright owner. http://www..net/ datasheet pdf - http://www..net/
18 programmed playback the program function enables you to store your favourite tracks from any disc in the receiver memory. a program can contain 300 tracks. 1. insert a disc. audio cd and mp3/wma discs: 2. select a track on the ?ist?and then press prog. or select (add)?icon and then press enter to place the selected track on the ?rogram?list. repeat to place additional tracks on the list. note: y ou can add all tracks in the disc. select ( add all)?icon then press enter. 3. select the track you want to start playing on the ?rogram?list. press menu to move to the next page. 4. press play or enter to start. playback begins in the order in which you programmed the tracks. playback stops after all of the tracks on the ?rogram?list have played once. 5. to resume normal playback from programmed playback, select a track of audio cd (or mp3/wma) list and then press play. repeat programmed tracks 1. press repeat when playing a disc. the repeat icon appears. 2. press repeat to select a desired repeat mode. ?track: repeats the current track ?all: repeats all the tracks on programmed list. ?off (no display): does not play repeatedly. erasing a track from ?rogram?list 1. use vv to select the track that you wish to erase from the program list. 2. press clear. alternatively, select (delete) icon then press enter to place the selected track on the program list. repeat to erase additional tracks on the list. erasing the complete program list use v / v to select (del all)?and then press enter. note: the programs are also cleared when the disc is removed, the unit is switched to power off or the function is switched to others. http://www..net/ datasheet pdf - http://www..net/
19 operation v iewing a jpeg file this unit can play discs with jpeg files. before playing jpeg recordings, read the notes on jpeg recordings on the right. 1. insert a disc and close the tray. the photo menu appears on the tv screen. 2. press v / v to select a folder, and then press enter. a list of files in the folder appears. if you are in a file list and want to return to the previous folder list, use the v / v buttons on the remote to highlight and press enter. 3. if you want to view a particular file, press v / v to highlight a file and press enter or play. while viewing a file, you can press stop to move to the previous menu (jpeg menu). tips: there are four slide speed options : > (slow), >> (normal), >>> (fast) and ii (off). use v / v / b / b to highlight the speed. then, use b / b to select the option you want to use and then press enter. if you set speed option to off, the slide is not active. slide show 1. highlight the file (not folder) which you like beginning to slide show. 2. select the slide speed. (refer to the tips this page) 3. use vvbb to highlight the (slide show) then press enter. note: the sequence of slide show is from top to down, cannot be reverse. slide show cannot repeat automatically, you could start the slide show again manually. still picture 1. press pause/step during the slide show. the dvd/cd receiver will now go into the pause mode. 2. to return to the slide show, press play or press p ause/step again. moving to another file press skip ( . or > ) once during viewing a picture to advance to the next or previous file. rotating the picture press vvbb during showing a picture to rotate the picture clockwise or counter-clockwise. jpeg disc compatibility with this player is limited as follows: depending upon the size and the number of jpeg files, it could take a long time for the dvd/cd receiver to read the discs contents. if you don? see an on-screen display after several minutes, some of the files may be too large reduce the resolution of the jpeg files to less than 2m pixels as 2760 x 2048 pixels and burn another disc. the total number of files and folders on the disc should be less than 999. some discs may not operate due to a different recording format or the condition of disc. ensure that all the selected files have the ?jpg extensions when copying into the cd layout. if the files have ?jpe?or ?jpeg?extensions, please rename them as ?jpg?file. file names without ?jpg?extension will not be able to be read by this dvd/cd receiver. even though the files are shown as jpeg image files in windows explorer. http://www..net/ datasheet pdf - http://www..net/
20 playing a divx movie file using this dvd/cd receiver you can play divx disc. 1. insert a disc and close the tray. the movie menu appears on the tv screen. 2. press v / v to select a folder and then press enter. a list of files in the folder appears. if you are in a file list and want to return to the folder list, use the v / v buttons on the remote to highlight and press enter. 3. if you want to view a particular file, press v / v to highlight a file and press enter or play. 4. press stop to exit. notice for displaying the divx subtitle if the subtitle does not display properly during playback, press and hold s-title for about 3 seconds then press s-title to select another language code until the subtitle is displayed properly tips: press menu to move to the next page. notes: be sure to select ?ubtitle on?mode by pressing the subtitle file every time before playing a divx file . when the subtile has more than two languages in the file, original subtile is only available. divx disc compatibility with this player is limited as follows: a vailable resolution size of the divx file is under 800x600 (w x h) pixel. the file name of the divx subtitle is available by 45 characters. if there is impossible code to express in the divx file, it may be displayed as " _ " mark on the display. if the number of the screen frame is over 30 per 1 second, this unit may not operate normally. if the video and audio structure of recorded files are not interleaved, either video or audio is outputted. playable divx file ".avi ", ".mpg ", ".mpeg ", ".divx" playable subtitle format subrip(*.srt/*.txt) sami(*.smi) substation alpha(*.ssa/*.txt) microdvd(*.sub/*.txt) subviewer 2.0(*.sub/*.txt) v obsub(*.sub) playable codec format "divx3.xx ", "divx4.xx ", "divx5.xx ", "mp43 ", "3ivx ". playable audio format "ac3 ", "dts ", "pcm ", "mp3 ", "wma ". ?sampling frequency: within 32 - 48 khz (mp3), within 24 - 48khz (wma) ?bit rate: within 32 - 320kbps (mp3), 40 - 192kbps (wma) http://www..net/ datasheet pdf - http://www..net/
21 operation presetting the radio stations y ou can preset 50 stations for fm and am (mw). before tuning, make sure that you have turned down the volume. 1. press function on the remote control until fm or am (mw) appears in the display window. 2. and then every time you press function, fm and am (mw) changes alternately. 3. press and hold tuning.(-/+) for about two seconds until the frequency indication starts to change, then release. scanning stops when the dvd/cd receiver tunes in a station. 4. press prog./memo. on the remote control. a preset number will flash in the display window. 5. press preset (-/+) on the remote control to select the preset number you want. 6. press prog./memo. on the remote control again. the station is stored. 7. repeat steps 3 to 6 to store other stations. to tune in a station with a weak signal press tuning.(-/+) repeatedly in step 3 to tune in the station manually. to clear all the stored stations press and hold prog./memo. for about two seconds and ?rase all?is appeared in the display window and then press prog./memo. again, the stations are cleared. if you have accidentally entered into the "erase all" mode and you do not wish to clear the memory, do not press any key. after a few seconds, "erase all" will go off by itself and change to normal mode. note: if all stations have already been entered, the full message will appear in the display window for a moment and then a preset number will flash. to change the preset number, follow the steps 5-6 as above. listening to the radio preset radio stations in the dvd/cd receivers memory first (see ?resetting radio stations?on the left). 1. press function until fm or am (mw) appears in the display window. the last received station is tuned in. 2. press preset (-/+) repeatedly on the remote control to select the preset station you want. each time you press the button, the dvd/cd receiver tunes in one preset station at a time. 3. adjust the volume by rotating volume on the front panel or by pressing volume + or - on the remote control repeatedly. to turn off the radio press power to turn the dvd/cd receiver off or select another function mode. to listen to non-preset radio stations use manual or automatic tuning in the step 2. for manual tuning, press tuning.(-/+) repeatedly. for automatic tuning, press and hold tuning.(-/+) for about two seconds on the front panel. to select a preset radio station directly y ou can use the number buttons on the remote control to select a preset radio station directly. for example, to listen to the preset station 4, press 4 on the remote control. to listen to the preset station 19, press 1 and then 9 (within 3 seconds). for your reference if an fm program is noisy press fm mode. on the front panel or on the remote control to make ?ono?appear in the display window. there will be no stereo effect, but the reception will improve. press the button again to restore the stereo effect. to improve reception reorient the supplied antennas. http://www..net/ datasheet pdf - http://www..net/
22 rds operation this unit is equipped with rds (radio data system), which brings a wide range of information to fm radio. rds, now being used in many countries, is a system for transmitting station call signs or network information, a description of station programme type text message about the station or specifics of musical selection and the correct time. rds tuning when a fm station is tuned in and it contains rds data, the unit will automatically display the stations call sign and the rds indicator will light in the display window as well as indicators for the rds services programme (ps), programme type recognition (pty), radio text (rt) and clock time (ct) if transmitted by the station. rds display options the rds system is capable of transmitting a wide variety of information in addition to the initial call sign that appears when a station is first tuned. in normal rds operation the display will indicate the station name, broadcast network or call letters. pressing rds display on the remote control enables you to cycle through the various data types in the sequence: (ps ? ? frequency ? ? pty ? ? rt ? ? ct) ps (programme service name)- the name of the channel is shown in the display window. pty (programme type recognition)- the name of the programme type is shown in the display window. rt (radiotext)- a ?ext?message contains special information from the broadcast station. note that this message may scroll across the display to permit message. ct (time controlled by the channel)- enables the unit to receive the actual time and show it in the display window. note: some rds stations may not choose to include some of these additional features. if the data required for the selected mode is not being transmitted, the display window will show a pty none, rt none, ct none, or ps none message. news news affairs current affairs info information sport sports educate educational drama drama culture culture science science v aried varied speech programme pop m popular music rock m rock music easy m easy listening music light m light music classics classical music other m other music weather weather information finance financial programmes children childrens programmes social social affairs programmes religion religious broadcasts phone in phone-in programmes travel travel and touring leisure leisure and hobby jazz jazz music country country music nation m national music oldies oldies music folk m folk music document documentary programmes test station alarm test message alarm ! emergency broadcast information programme search (pty) a major benefit of rds is its ability to encode broadcasts with programme type (pty) codes that indicate the type of material being broadcast. the following list shows the abbreviations used to indicate each pty along with an explanation of the pty. y ou may search for a specific programme type (pty) by following these steps: 1. press function to select the fm mode. 2. press pty search on the remote control, the display will show the last pty in use. 3. press pty search repeatedly to select a desired pty. 4. when the pty is selected, press tuning ( # # / 3 3 ). the unit will go into an automatic search mode. when a station is tuned, the search will stop. http://www..net/ datasheet pdf - http://www..net/
23 operation sleep timer setting y ou can set the dvd/cd receiver to turn off automatically at a specified time. 1. press sleep to set the desired sleep time. the sleep indicator and the sleep time appears in the display window. 2. each time you press sleep the setting changes in the following order. sleep 180 150 120 90 80 70 60 50 40 30 20 10 off (no display) note: y ou can check the remaining time before the dvd/cd receiver turns off. press sleep. the remaining time appears in the display window. dimmer this function will change the brightness of the display window on the front panel during in power-on status. press the dimmer repeatedly. muting press muting to mute your unit. y ou can mute your unit in order, for example, to answer the telephone, the ?uting?indicator flashes in the display window. note: this muting doesn? affect the audio output to hdmi; it only mutes the output of speakers connected to the unit. setting the disc ejection lock y ou can lock the disc tray to prevent the disc form being ejected. when the main unit is turned off, hold down the stop key at the front panel for 5 seconds if you attempt to open the disc tray by pressing open/close key, the disc tray does not open and ?ocked?appears in the display window. to cancel the disc ejection lock, hold down the stop key at the front panel for 5 seconds again when the main unit is turned off. ?nlocked?is displayed in the display window. note: before the main unit is turned off, dvd/cd function should be selected. enjoying audio form an external source y ou can enjoy audio form an external source through your unit. press input repeatedly to select the desired input source. - aux, aux opt, tv-audio, audio in, usb setting the surround mode y ou can select the dolby pro logic ii. press surround to change surround mode repeatly. [bypass] mode : software with multichannel surround audio signals is played according to the way it was recorded. [pl ii movie] mode: the movie mode is for use with stereo television shows and all programs encoded in dolby surround. the result is enhanced soundfield directionality that approaches the quality of discrete 5.1-channel sound. [pl ii music] mode: the music mode is for use with any stereo music recordings. [pl ii matrix] mode: the matrix mode is the same as the music mode except that the directional enhancement logic is turned off. it may be used to enhance mono signals by making them seem ?arger.?the matrix mode may also find use in auto systems, where the fluctuations from poor fm stereo reception can otherwise cause disturbing surround signals from a logic decoder. the ultimate ?ure?for poor fm stereo reception may be simply to force the audio to mono. notes: in some of surround modes, some speakers maybe no sound or low sound, it depends on the mode of surround and the source of audio, it is not defective. ? ou may need resetting the surround mode, after switch the input, sometimes even after the sound track changed. http://www..net/ datasheet pdf - http://www..net/
24 area code afghanistan af argentina ar australia au austria at belgium be bhutan bt bolivia bo brazil br cambodia kh canada ca chile cl china cn colombia co congo cg costa rica cr croatia hr czech republic cz denmark dk ecuador ec egypt eg el salvador sv area code ethiopia et fiji fj finland fi france fr germany de great britain gb greece gr greenland gl heard and mcdonald islands hm hong kong hk hungary hu india in indonesia id israel il italy it jamaica jm japan jp kenya ke kuwait kw libya ly luxembourg lu area code malaysia my maldives mv mexico mx monaco mc mongolia mn morocco ma nepal np netherlands nl netherlands antilles an new zealand nz nigeria ng norway no oman om pakistan pk panama pa paraguay py philippines ph poland pl portugal pt romania ro russian federation ru area code saudi arabia sa senegal sn singapore sg slovak republic sk slovenia si south africa za south korea kr spain es sri lanka lk sweden se switzerland ch t aiwan tw thailand th t urkey tr uganda ug ukraine ua united states us uruguay uy uzbekistan uz vi etnam vn zimbabwe zw area codes choose a area code from this list. language code abkhazian 6566 afar 6565 afrikaans 6570 albanian 8381 ameharic 6577 arabic 6582 armenian 7289 assamese 6583 a ymara 6588 azerbaijani 6590 bashkir 6665 basque 6985 bengali; bangla 6678 bhutani 6890 bihari 6672 breton 6682 bulgarian 6671 burmese 7789 byelorussian 6669 cambodian 7577 catalan 6765 chinese 9072 corsican 6779 croatian 7282 czech 6783 danish 6865 dutch 7876 english 6978 esperanto 6979 estonian 6984 faroese 7079 language code fiji 7074 finnish 7073 french 7082 frisian 7089 galician 7176 georgian 7565 german 6869 greek 6976 greenlandic 7576 guarani 7178 gujarati 7185 hausa 7265 hebrew 7387 hindi 7273 hungarian 7285 icelandic 7383 indonesian 7378 interlingua 7365 irish 7165 italian 7384 japanese 7465 javanese 7487 kannada 7578 kashmiri 7583 kazakh 7575 kirghiz 7589 korean 7579 kurdish 7585 laothian 7679 latin 7665 latvian, lettish 7686 language code lingala 7678 lithuanian 7684 macedonian 7775 malagasy 7771 malay 7783 malayalam 7776 maltese 7784 maori 7773 marathi 7782 moldavian 7779 mongolian 7778 nauru 7865 nepali 7869 norwegian 7879 oriya 7982 panjabi 8065 pashto, pushto 8083 persian 7065 polish 8076 portuguese 8084 quechua 8185 rhaeto-romance 8277 rumanian 8279 russian 8285 samoan 8377 sanskrit 8365 scots gaelic 7168 serbian 8382 serbo-croatian 8372 shona 8378 sindhi 8368 language code singhalese 8373 slovak 8375 slovenian 8376 somali 8379 spanish 6983 sudanese 8385 swahili 8387 swedish 8386 t agalog 8476 t ajik 8471 t amil 8465 t atar 8484 t elugu 8469 thai 8472 t ibetan 6679 t igrinya 8473 t onga 8479 t urkish 8482 t urkmen 8475 tw i 8487 ukrainian 8575 urdu 8582 uzbek 8590 v ietnamese 8673 v olap?k 8679 w elsh 6789 w olof 8779 xhosa 8872 y iddish 7473 y oruba 8979 zulu 9085 language codes use this list to input your desired language for the following initial settings: disc audio, disc subtitle, disc menu. http://www..net/ datasheet pdf - http://www..net/
25 reference t roubleshooting check the following guide for the possible cause of a problem before contacting service. symptom no power. the power is on, but the dvd/cd receiver does not work. no picture. there is no sound or only a very low-level sound is heard. the playback picture is poor. the dvd/cd receiver does not start playback. loud hum or noise is heard. cause the power cord is disconnected. no disc is inserted. the tv is not set to receive dvd signal output. the video cable is not connected securely. the connected tv power is turned off. the equipment connected with the audio cable is not set to receive dvd signal output. the audio cables are not connected securely. the power of the equipment connected with the audio cable is turned off. the audio connecting cable is dam aged. the disc is dirty. no disc is inserted. an unplayable disc is inserted. the disc is placed upside down. the disc is not placed within the guide. the disc is dirty. ? menu is on the tv screen. the rating level is set. the disc is dirty. the speakers and components are connected poorly. the dvd/cd receiver is located too close to the tv. correction plug the power cord securely into the wall outlet. insert a disc. (check that the dvd or, audio cd indicator in the dvd display is lit.) select the appropriate video input mode on the tv so the picture from the dvd/cd receiver appears on the tv screen. connect the video cable into the jacks securely. ? urn on the tv. select the correct input mode of the audio receiver so you can hear the sound from the dvd/cd receiver. connect the audio cable into the jacks securely. ? urn on the equipment connected with the audio cable. replace it with new one. clean the disc. insert a disc. (check that the dvd, or audio cd indicator in the dvd display is lit.) insert a playable disc. (check the disc type, colour system and regional code.) place the disc with the playback side down. place the disc on the disc tray correctly inside the guide. clean the disc. press the setup button to turn off the menu screen. cancel the rating function or change the rating level. clean the disc. connect the speakers and components securely. move your tv away from the audio components. http://www..net/ datasheet pdf - http://www..net/
26 symptom radio stations cannot be tuned in. the remote control does not work properly. the front panel display is too dim. cause the antenna is positioned or connected poorly. the signal strength of the stations is too weak (when tuning in with automatic tuning). no stations have been preset or preset stations have been cleared (when tuning by scanning preset stations). the remote control is not pointed at the remote sensor of the dvd/cd receiver. the remote control is too far from the dvd/cd receiver. there is an obstacle in the path of the remote control and the dvd/cd receiver. the batteries in the remote control are flat. nothing is displayed on the front panel display. correction connect the antenna securely. adjust the antennas and connect an external antenna if necessary. ? une in the station manually. preset the stations (page 21). point the remote control at the remote sensor of the dvd/cd receiver. use the remote control within about 23 ft (7 m). remove the obstacle. replace the batteries with new ones. press dimmer on the remote control. http://www..net/ datasheet pdf - http://www..net/
27 reference ? 20 - 240 v ~ 50/60 hz power consumption 130 w net weight 4 kg external dimensions (w x h x d) 430 x 72 x 307 mm operating conditions temperature: 5?c to 35?c, operation status: horizontal operating humidity 5% to 85% laser semiconductor laser, wavelength 650 nm v ideo system pal/ntsc frequency response (audio) 140 hz to 20 khz signal-to-noise ratio (audio) more than 75 db (1 khz, 20 khz lpf/a-filter) dynamic range (audio) more than 75 db harmonic distortion (audio) 0.5 % (1 khz, at 1w position) (20 khz lpf) v ideo output 1.0 v (p-p), 75 , negative sync., rca jack x 1 / scart (to tv) component video out (y) 1.0 v (p-p), 75 ohms, negative sync, rca jack x 1 (p b )/(p r ) 0.7 v (p-p), 75 ohms, rca jack x 2 hdmi out 480p (or 576p)/720p/1080i/1080p t uning range 87.5 - 108.0 mhz (87.50 - 108.00 mhz) intermediate frequency 10.7 mhz signal-to noise ratio 60 db (mono) frequency response 140 - 10,000 hz t uning range 522 - 1,620 khz intermediate frequency 450 khz stereo mode 155 w + 155 w (4 at 1 khz, thd 10 %) surround mode front: 155 w + 155 w (thd 10 %) center*: 155 w surround*: 155 w + 155 w (4 at 1 khz, thd 10 %) subwoofer*: 225 w (3 at 70 hz, thd 10 %) inputs audio in, optical in, aux in, usb port, tv-audio(scart) outputs monitor out, hdmi out, scart component video out front/rear speaker center speaker passive subwoofer t ype 1 way 1 speaker 1 way 1 speaker 1 way 1 speaker impedance 4 4 3 frequency response 120 - 20000 hz 120 -20000 hz 40 - 1500 hz sound pressure level 83 db/w (1m) 83 db/w (1m) 82 db/w (1m) rated input power 155 w 155 w 225 w max. input power 310 w 310 w 450 w net dimensions (w x h x d) 1 17 x 210 x 111 mm 300 x 115 x 111 mm 236 x 435 x 391 mm net weight 0.9 kg 1.1 kg 5.7 kg items with are measured at front speaker terminals in stereo mode (* depending on the sound mode settings and the source, there may be no sound output.) supplied accessories fm antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . .x1 am antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . .x1 speaker cable . . . . . . . . . . . . . . . . . . . . . . . . . . .x6 remote control . . . . . . . . . . . . . . . . . . . . . . . . . .x1 v ideo rca cable . . . . . . . . . . . . . . . . . . . . . . . . .x1 batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .x2 am http://www..net/ datasheet pdf - http://www..net/
0608skmlgeegl TH-G30 2008 victor company of japan, limited en http://www..net/ datasheet pdf - http://www..net/

▲Up To Search▲

Price & Availability of TH-G30

	To Download TH-G30 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .