383 ca-relays automotive power relays small size, light weight and completely water tight features 1. small size and light weight for space saving, the outside dimensions of the main body are reduced to be 21.5 mm (length) 14.4 mm (width) 37 mm (height) (.846 .567 1.457 inch) . and the weight is also reduced to be approx. 19 g .67 oz (direct coupling 1 form a, 1 form b type) 2. water tightness since the relays comply with the water tightness standards, jis d 0203, water and dust will not enter the relay even if it is mounted in the engine area. 3. low operaing power (1.4w) type is available (1 form a, 1 form b) 4. since the terminal arrangement complies with jis d5011 b4-m1, com- mercial connectors are available for these types of relays. specifications contact type 12 v dc 24 v dc arrangement 1 form a 1 form b 1 form c 1 form c initial contact resistance, max. (by voltage drop 6 v dc 1a) 50 m ohm contact material silver alloy contact voltage drop, max. 0.3 v after electrical life test, by voltage drop 12 v dc 20 a (1.4 w type), 12 v dc 30 a (1.8 w type) 0.3 v after electrical life test, by voltage drop 12 v dc 20 a 0.4 v after electrical life test, by voltage drop 12 v dc 20 a 0.4 v after electrical life test, by voltage drop 24 v dc 10 a rating nominal switching capacity (resistive load) 20 a 12 v dc (1.4 w type) 30 a 12 v dc (1.8 w type) 20 a 12 v dc 10 a 24 v dc (on: 2s, off: 2s) max. switching voltage 16 v 15 v 30 v max. switching current 120 a (1.4 w type) 150 a (1.8 w type) 120 a 100 a 50 a (inrush current) max. carrying current 20 a continuous (1.4 w type) 30 a for 1 min (1.8 w type) 20 a continuous 20 a continuous 10 a continuous nominal operating power 1.4 w / 1.8 w 1.8 w expected life (min. operations) mechanical (at 120 cpm) 10 6 5 10 5 electrical 20 a (1.4 w, 1.8 w type) 10 5 (on: 2s, off: 2s) 10 5 (on 2s, off 2s) 10 5 30 a (1.8 w type) 2 10 4 (on: 3s, off: 15s)
ca 384 characteristics (at 20 c 68 f ) electrical life (min. operation) remarks * speci?cations will vary with foreign standards certi?cation ratings. * 1 detection current: 10 ma * 2 excluding contact bounce time * 3 half-wave pulse of sine wave: 11ms; detection time: 10 m s * 4 half-wave pulse of sine wave: 6ms * 5 detection time: 10 m s * 6 refer to 5. conditions for operation, transport and storage mentioned in ambient environment (page 61) type 12 v dc 24 v dc max. operating speed 15 cpm 1.4 w type: at nominal load 1.8 w type: at 20 a 15 cpm (at nominal load) initial insulation resistance min. 10 w at 500 v dc initial breakdown voltage* 1 between open contacts 500 v rms for 1 min. between contacts and coil 500 v rms for 1 min. operate time* 2 (at nominal voltage) max. 10 ms at 20 c max. 10 ms release time (without diode)* 2 (at nominal voltage) max. 10 ms at 20 c max. 10 ms shock resistance functional min. 200 m/s 2 {20 g} min. 100 m/s 2 {10 g} min. 100 m/s 2 {10 g}* 3 destructive* 4 min. 1,000 m/s 2 {100 g} vibration resistance functional* 5 rubber bracket a type: min. 100 m/s 2 {10 g}, 50 to 500hz direct coupling type or screw-mounting type: min. 44.1 m/s 2 {4.5 g}, 10 to 100 hz min. 44.1 m/s 2 {4.5 g}, 10 to 100hz destructive rubber bracket a type: min. 100m/s 2 {10 g},50 to 500hz direct coupling type or screw-mounting type: min. 44.1 m/s 2 {4.5 g}, 10 to 100 hz min. 44.1 m/s 2 {4.5 g}, 10 to 500hz conditions for operation, transport and storage* 6 (not freezing and condensing low temperature) ambient temp. C30 c to +80 c C22 f to +176 f humidity 5 to 85% r.h. water-proof standard plastic sealed type: jis do203s2, dust cover type: jis do203r2 jis do203s2 unit weight rubber bracket a type : 23 g . 81 oz direct coupling type or screw-mounting type: 19 g . 67 oz 31 g 1.09 oz nominal coil voltage, v dc motor load (operating frequency on: 2 s, off: 2 s) halogen lamp load (operating frequency on: 1 s, off: 14 s) 1 form a, 1 form b 12 10 5 , 20 a 12 v dc 10 5 , 20 a 12 v dc 1 form c 12 10 5 , 20 a 12 v dc 10 5 , 20 a 12 v dc 24 10 5 , 10 a 24 v dc 10 5 , 6 a 24 v dc ordering information ca 1a f s 12 v a 5 contact arrangement notes: 1. type with resistor/diode inside are available as options. please consulf our sales office. 2. standard packing: carton: 20 pcs. case: 200 pcs. mounting method classification by type 1a: 1 form a 1b: 1 form b 1 : 1 form c protective construction nil: plastic sealed type f: dust cover type coil voltage (dc) 12 v 24 v (1 form c only) nil: 1 form c 5: 1 form a or 1 form b nominal operating power nil: standard type (1.8 w) s: low operating power type (1.4 w) (1 form a, 1 form b) a: rubber bracket a type a: (1 form a, 1 form b) n: screw mounting type c: direct coupling type coil data 1) standard type contact arrangement mounting type plastic sealed type dust cover type nominal voltage, v dc pick-up voltage, v dc (max.) (at 20 c 68 f ) drop-out voltage, v dc (min.) (at 20 c 68 f ) nominal oper- ating current, ma ( 10%) (at 20 c 68 f ) coil resistance, w ( 10%) (at 20 c 68 f ) nominal operating power, mw (at 20 c 68 f ) usable voltage range, v dc 1 form a rabber bracket a ca1a-12v-a-5 ca1af-12v-a-5 12 8 0.6 to 6 150 80 1.8 10 to 16 screw-mounting ca1a-12v-n-5 ca1af-12v-n-5 12 8 0.6 to 6 150 80 1.8 10 to 16 direct coupling ca1a-12v-c-5 ca1af-12v-c-5 12 8 0.6 to 6 150 80 1.8 10 to 16 1 form b rabber bracket a ca1b-12v-a-5 ca1bf-12v-a-5 12 8 0.6 to 6 150 80 1.8 10 to 16 screw-mounting ca1b-12v-n-5 ca1bf-12v-n-5 12 8 0.6 to 6 150 80 1.8 10 to 16 direct coupling ca1b-12v-c-5 ca1bf-12v-c-5 12 8 0.6 to 6 150 80 1.8 10 to 16 1 form c screw-mounting ca1-dc12v-n C 12 8 0.6 150 80 1.8 10 to 15 direct coupling ca1-dc12v-c C 12 8 0.6 150 80 1.8 10 to 15 screw-mounting ca1-dc24v-n C 24 16 1.2 75 320 1.8 20 to 30 direct coupling CA1-DC24V-C C 24 16 1.2 75 320 1.8 20 to 30 ()
ca 385 2) low operating power type dimensions 1. 1 form a/1 form b rubber bracket a type contact arrangement mounting type plastic sealed type dust cover type nominal voltage, v dc pick-up voltage, v dc (max.) (at 20 c 68 f ) drop-out voltage, v dc (min.) (at 20 c 68 f ) nominal oper- ating current, ma ( 10%) (at 20 c 68 f ) coil resistance, w ( 10%) (at 20 c 68 f ) nominal operating power, mw (at 20 c 68 f ) usable voltage range, v dc 1 form a rabber bracket a ca1as-12v-a-5 ca1afs-12v-a-5 12 8 0.6 to 6 120 100 1.4 10 to 16 screw-mounting ca1as-12v-n-5 ca1afs-12v-n-5 12 8 0.6 to 6 120 100 1.4 10 to 16 direct coupling ca1as-12v-c-5 ca1afs-12v-c-5 12 8 0.6 to 6 120 100 1.4 10 to 16 1 form b rabber bracket a ca1bs-12v-a-5 ca1bfs-12v-a-5 12 8 0.6 to 6 120 100 1.4 10 to 16 screw-mounting ca1bs-12v-n-5 ca1bfs-12v-n-5 12 8 0.6 to 6 120 100 1.4 10 to 16 direct coupling ca1bs-12v-c-5 ca1bfs-12v-c-5 12 8 0.6 to 6 120 100 1.4 10 to 16 21.5 .846 19.5 .768 9 .354 37 1.457 14.4 .567 17.4 .685 10 .394 15 .591 2.5 .098 6 .236 21.5 .846 17 .669 0.8 .031 15.4 .606 12.4 .488 5.5 .217 2.4 .094 1.5 .059 2 .079 sealed with epoxy resin dimension: gener al toler ance max. 1mm .039 inch : 0.1 .004 1 to 3mm .039 to .118 inch : 0.2 .008 min. 3mm .118 inch : 0.3 .012 mm inch schematic (bottom view) 1 form a including load (1 form a) including diode (1 form c) 1 form b including diode type, including load type also available. 2. 1 form a/1 form b screw-mounting type 14 .551 9 .354 2 .079 17.4 .685 21.5 .846 3 .118 14.4 .567 6 .236 0.8 .031 15.4 .606 12.4 .488 5.5 .217 2.4 .094 17.5 .689 37 1.457 7 .276 r10 6.5 dia. hole +0.3 0 .256 dia. +.012 0 sealed with epoxy resin 19.5 .768 dimension: gener al toler ance max. 1mm .039 inch : 0.1 .004 1 to 3mm .039 to .118 inch : 0.2 .008 min. 3mm .118 inch : 0.3 .012 schematic (bottom view) 1 form a including load (1 form a) including diode (1 form c) 1 form b including diode type, including load type also available.
ca 386 3. 1 form a/1 form b direct coupling type 21.5 .846 9 .354 17.4 .685 14.4 .567 6 .236 0.8 .031 15.4 .606 12.4 .488 5.5 .217 2.4 .094 37 1.457 sealed with epoxy resin 19.5 .768 dimension: gener al toler ance max. 1mm .039 inch : 0.1 .004 1 to 3mm .039 to .118 inch : 0.2 .008 min. 3mm .118 inch : 0.3 .012 mm inch schematic (bottom view) 1 form a including load (1 form a) including diode (1 form c) 1 form b including diode type, including load type also available. 4. 1 form c screw-mounting type 14 .551 23.4 .921 19.4 .764 31.2 1.228 4 .157 2 .079 5.5 .217 2.4 .094 0.8 .031 12.2 .480 12 .472 40 1.575 59 2.323 28 1.102 r10 6.6 dia. hole .260 dia. 28.4 1.118 20 .787 9 .354 9 .354 6 .236 11.4 .449 sealed with epoxy resin dimension: gener al toler ance max. 1mm .039 inch : 0.1 .004 1 to 3mm .039 to .118 inch : 0.2 .008 min. 3mm .118 inch : 0.3 .012 schematic (bottom view) including diode type, including load type also available. including load (1 form c) including diode (1 form a) 1 form c 5. 1 form c direct coupling type 19.4 .764 5.5 .217 2.4 .094 0.8 .031 12.2 .480 40 1.575 28 1.102 9 .354 9 .354 6 .236 11.4 .449 sealed with epoxy resin 23.4 .921 31.2 1.228 28.4 1.118 dimension: gener al toler ance max. 1mm .039 inch : 0.1 .004 1 to 3mm .039 to .118 inch : 0.2 .008 min. 3mm .118 inch : 0.3 .012 schematic (bottom view) including diode type, including load type also available. including load (1 form c) including diode (1 form a) 1 form c
ca 387 reference data 1. coil temperature rise tested sample: ca1as-12v-n-5, 5 pcs. point measured: inside the coil contact carrying current: 20a ambient temperature: room temperature, 85 c 185 f 2. electrical life test (motor load) tested sample: ca1a-12v-n-5, 5 pcs. load: steady 30a, inrush 150a, 12v dc operate frequency: on 3s, off 15s ambient temperature: room temperature 12 14 16 140 120 100 80 60 40 20 0 85 c 185 f room temperature temperature rise, c coil applied voltage, v 0 2 4 6 8 10 02 x x max. max. min. min. pick-up and drop-out voltage, v no. of operations, 10 4 contact welding: 0 times miscontact: 0 times pick-up voltage drop-out voltage for cautions for use, see relay technical information (page 48 to 76). 9/1/2000 all rights reserved, ? copyright matsushita electric works, ltd. go to online catalog
|
