View HLMP-6620-F001S_6373427.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

features ? subminiature fl at top package C ideal for backlighting and light piping applications ? subminiature dome package C diff used dome for wide viewing angle C nondiff used dome for high brightness ? ttl and lsttl compatible 5 volt resistor lamps ? available in six colors ? ideal for space limited applications ? axial leads ? available with lead confi gurations for surface mount and through hole pc board mounting description flat top package the hlmp-pxxx series fl at top lamps use an untinted, non- diff used, truncated lens to provide a wide radiation pat- tern that is necessary for use in backlighting applications. the fl at top lamps are also ideal for use as emitters in light pipe applications. dome packages the hlmp-6xxx series dome lamps for use as indicators use a tinted, diff used lens to provide a wide viewing angle with a high on-off contrast ratio. high brightness lamps use an untinted, nondiff used lens to provide a high lumi- nous intensity within a narrow radiation pattern. resistor lamps the hlmp-6xxx series 5 volt subminiature lamps with built in current limiting resistors are for use in applications where space is at a premium. lead confi gurations all of these devices are made by encapsulating led chips on axial lead frames to form molded epoxy subminiature lamp packages. a variety of package confi guration op- tions is avail able. these include special sur face mount lead confi gura tions, gull wing, yoke lead or z-bend. right angle lead bends at 2.54 mm (0.100 inch) and 5.08 mm (0.200 inch) center spacing are available for through hole mounting. for more information refer to standard smt and through hole lead bend options for subminiature led lamps data sheet. hlmp-pxxx series, hlmp-qxxx series hlmp-6xxx series, hlmp-70xx series subminiature led lamps data sheet
2 device selection guide part number: hlmp-xxxx dh as high high device standard algaas effi ciency perf. emerald outline red red red orange yellow green green device description [1] drawing p005 p105 p205 p405 p305 p505 p605 untinted, nondiff used, a flat top p102 p202 p402 p302 p502 untinted, diff used, flat top a 6000 q100 6300 q400 6400 6500 q600 tinted, diff used b q105 6305 q405 6405 6505 q605 untinted, nondiff used, b high brightness q150 7000 7019 7040 tinted, diff used, low current b q155 nondiff used, low current b 6600 6700 6800 tinted, diff used, resistor, b 5 v, 10 ma 6620 6720 6820 diff used, resistor, 5 v, 4 ma b ordering information hlmx- xxxx-x x x x x 4 x 4 prod. part number min. iv bin max. iv bin color bin selection packaging option
3 0.50 (0.020) ref. 0.94 1.24 (0.037) (0.049) 2.92 (0.115) max. 0.76 0.89 (0.030) (0.035) r. 0.63 0.38 (0.025) (0.015) 2.03 (0.080) 1.78 (0.070) 0.79 (0.031) 0.53 (0.021) 0.46 0.56 (0.018) (0.022) 0.25 (0.010) max. note 2 0.20 (0.008) max. cathode 1.65 1.91 (0.065) (0.075) dia. anode 11.68 10.67 (0.460) (0.420) both sides 0.18 0.23 (0.007) (0.009) 2.08 2.34 (0.082) (0.092) cathode stripe 2.21 1.96 (0.087) (0.077) (b) diff used and nondiff used figure 1. proper right angle mounting to a pc board to prevent protruding cathode tab from shorting to anode connection. package dimensions (a) flat top lamps no. anode down. yes. cathode down. cathode tab notes: 1. all dimensions are in millimetres (inches). 2. protruding support tab is connected to cathode lead. 3. lead polarity for algaas lamps is opposite to the lead polarity of subminiature lamps using other technologies. 0.46 0.56 (0.018) (0.022) 1.40 1.65 (0.055) (0.065) 0.25 (0.010) max. note 2 0.20 (0.008) max. 0.50 (0.020) ref. cathode 1.65 1.91 (0.065) (0.075) dia. anode 11.68 10.67 (0.460) (0.420) both sides 1.14 1.40 (0.045) (0.055) 0.63 0.38 (0.025) (0.015) 2.21 1.96 (0.087) (0.077) 0.18 0.23 (0.007) (0.009) 0.79 (0.031) max. 2.44 1.88 (0.096) (0.074) 2.08 2.34 (0.082) (0.092) cathode stripe
4 absolute maximum ratings at t a = 25c dh as high standard algaas eff . high perf. emerald parameter red red red orange yellow green green units dc forward current [1] 50 30 30 30 20 30 30 ma peak forward current [2] 1000 300 90 90 60 90 90 ma dc forward voltage 6 6 6 6 v (resistor lamps only) reverse voltage (i r = 100 a) 5 5 5 5 5 5 5 v transient forward current [3] 2000 500 500 500 500 500 500 ma (10 s pulse) operating temperature range: non-resistor lamps -55 to +100 -40 to +100 55 to +100 -40 to +100 -20 to +100 c resistor lamps -40 to +85 -20 to +85 storage temperature range -55 to +100 c for thru hole devices 260c for 5 seconds wave soldering temperature [1.6 mm (0.063 in.) from body] for surface mount devices: 260c for 20 seconds refl ow soldering temperature notes: 1. see figure 5 for current derating vs. ambien t temperature. derating is not applicable to resistor lamps. 2. refer to figure 6 showing max. tolerable peak cu rrent vs. pulse duration to establish pulsed operating conditions. 3. the transient peak current is the maximum non-recurring peak current the device can withstand without failure. do not opera te these lamps at this high current.
5 electrical/optical characteristics, t a = 25c standard red device hlmp- parameter symbol min. typ. max. units test conditions 6000-e00xx 0.63 1.2 6000-g00xx luminous intensity [1] i v 1.60 3.2 mcd i f = 10 ma p005-f00xx 1.0 2.5 forward voltage v f 1.4 1.6 2.0 v i f = 10 ma all reverse breakdown v r 5.0 12.0 v i r = 100 a voltage 6000 included angle between 2 ? 1 / 2 90 deg. p005 half intensity points [2] 125 peak wavelength ? peak 655 nm dominant wavelength [3] ? d 640 nm spectral line half width ?? 1/2 24 nm all speed of response ? s 15 ns capacitance c 100 pf v f = 0; f = 1 mhz thermal resistance r ? j-pin 170 c/w junction-to-cathode lead luminous effi cacy [4] ? v 65 lm/w
6 dh as algaas red device hlmp- parameter symbol min. typ. max. units test conditions p102-f00xx 1.0 20.0 p105-l00xx 10.0 30.0 p105-np000 25 80 q100-m00xx 16 45 q100-n00xx luminous intensity i v 25.0 45.0 mcd i f = 20 ma q100-pq000 40 125 q105-p00xx 40 200 q105-st000 160 500 q150-f00xx 1.0 1.8 i f = 1 ma q155-f00xx 1.0 4.0 q100 forward voltage v f 1.8 2.2 v i f = 20 ma q150/q155 1.6 1.8 i f = 1 ma all reverse breakdown voltage v r 5.0 15.0 v i r = 100 a p105 125 q100/q150 included angle between 2 ? 1 / 2 90 deg. q105/q155 half intensity points [2] 28 peak wavelength ? peak 645 nm measured at peak dominant wavelength [3] ? d 637 nm spectral line half width ?? 1/2 20 nm all speed of response ? s 30 ns exponential time constant; e -t/ ? s capacitance c 30 pf v f = 0; f = 1 mhz thermal resistance r ? j-pin 170 c/w junction-to cathode lead luminous effi cacy [4] ? v 80 lm/w
7 high effi ciency red device hlmp- parameter symbol min. typ. max. units test conditions p202-f00xx 1.0 5.0 p205-f00xx 1.0 8.0 p205-jk000 4.0 12.5 i f = 10 ma 6300-f00xx 1.0 10.0 6300-kl000 luminous intensity [1] i v 6.3 20.0 mcd 6305-l00xx 10.0 40.0 7000-d00xx 0.4 1.0 i f = 2 ma 6600-g00xx 1.6 5.0 v f = 5.0 volts 6620-f00xx 1.0 2.0 all forward voltage v f 1.5 1.8 3.0 v i f = 10 ma (nonresistor lamps) 6600 forward current i f 9.6 13.0 ma v f = 5.0 v 6620 (resistor lamps) 3.5 5.0 all reverse breakdown voltage v r 5.0 30.0 v i r = 100 a p205 125 6305 included angle between 2 ? 1 / 2 28 deg. all diff used half intensity points [2] 90 peak wavelength ? peak 635 nm measured at peak dominant wavelength [3] ? d 626 nm spectral line half width ?? 1/2 40 nm all speed of response ? s 90 ns capacitance c 11 pf v f = 0; f = 1 mhz thermal resistance r ? j-pin 170 c/w junction-to-cathode lead luminous effi cacy [4] ? v 145 lm/w
8 orange device hlmp- parameter symbol min. typ. max. units test conditions p402-f00xx 1.0 4.0 p405-f00xx 1.0 6 p405-jk000 luminous intensity i v 4.0 12.5 mcd i f = 10 ma q400-f00xx 1.0 8 q405-h00xx 2.5 14 all forward voltage v f 1.5 1.9 3.0 v i f = 10 ma reverse breakdown voltage v r 5.0 30.0 v i r = 100 a p40x included angle between 2 ? 1 / 2 125 deg. q40x half intensity points [2] 90 peak wavelength ? peak 600 nm dominant wavelength [3] ? d 602 nm measured at peak spectral line half width ?? 1/2 40 nm all speed of response ? s 260 ns capacitance c 4 pf v f = 0; f = 1 mhz thermal resistance r ? j-pin 170 c/w junction-to-cathode lead luminous effi cacy [4] ? v 380 lm/w
9 yellow device hlmp- parameter symbol min. typ. max. units test conditions p302-f00xx 1.0 3.0 p305-f00xx 1.0 4.0 6400-f00xx 1.0 9.0 6400-jk000 4.0 12.5 i f = 10 ma 6405-j00xx luminous intensity [1] i v 3.6 20 mcd 6405-mn0xx 16 50 7019-d00xx 0.4 0.6 i f = 2 ma 6700-g00xx 1.4 5.0 v f = 5.0 volts 6720-f00xx 0.9 2.0 all forward voltage v f 2.0 2.4 v i f = 10 ma (nonresistor lamps) 6700 forward current i f 9.6 13.0 ma v f = 5.0 v 6720 (resistor lamps) 3.5 5.0 all reverse breakdown v r 5.0 50.0 v voltage p305 included angle between 125 6405 half intensity points [2] 2 ? 1 / 2 28 deg. all diff used 90 peak wavelength ? peak 583 nm measured at peak dominant wavelength [3] ? d 585 nm spectral line half width ?? 1/2 36 nm all speed of response ? s 90 ns capacitance c 15 pf v f = 0; f = 1 mhz thermal resistance r ? j-pin 170 c/w junction-to-cathode lead luminous effi cacy [4] ? v 500 lm/w
10 high performance green device hlmp- parameter symbol min. typ. max. units test conditions p502-f00xx 1.0 3.0 p505-g00xx 1.6 6.3 i f = 10 ma 6500-f00xx 1.0 7.0 6505-l00xx luminous intensity [1] i v 10.0 40.0 mcd 7040-d00xx 0.4 0.6 i f = 2 ma 6800-g00xx 1.6 5.0 v f = 5.0 volts 6820-f00xx 1.0 2.0 all forward voltage v f 2.1 2.7 v i f = 10 ma (nonresistor lamps) 6800 forward current i f 9.6 13.0 ma v f = 5.0 v 6820 (resistor lamps) 3.5 5.0 all reverse breakdown voltage v r 5.0 50.0 v i r = 100 a p505 included angle between 125 6505 half intensity points [2] 2 ? 1 / 2 28 deg. all diff used 90 peak wavelength ? peak 565 nm dominant wavelength [3] ? d 569 nm spectral line half width ?? 1/2 28 nm all speed of response ? s 500 ns capacitance c 18 pf v f = 0; f = 1 mhz thermal resistance r ? j-pin 170 c/w junction-to-cathode lead luminous effi cacy [4] ? v 595 lm/w notes: 1. the luminous intensity for arrays is tested to assure a 2.1 to 1.0 matching between elements. the average luminous intensit y for an array determines its light output category bin. arrays are binned for luminous intensity to allow i v matching between arrays. 2. ? 1 / 2 is the off -axis angle where the luminous intensity is half the on-axis value. 3. dominant wavelength, ? d , is derived from the cie chromaticity diagram and represents the single wavelength that defi nes the color of the device. 4. radiant intensity, i e , in watts/steradian, may be calculated from the equation i e = i v / ? v , where i v is the luminous intensity in candelas and ? v is the luminous effi cacy in lumens/watt.
11 emerald green [1] device hlmp- parameter symbol min. typ. max. units test conditions p605-f00xx 1.0 1.5 q600-f00xx luminous intensity i v 1.0 1.5 mcd i f = 10 ma q605-f00xx 1.0 7.5 all forward voltage v f 2.2 3.0 v i f = 10 ma reverse breakdown voltage v r 5.0 v i r = 100 a p605 included angle between 2 ? 1 / 2 125 deg. q60x half intensity points [2] 90 peak wavelength ? peak 558 nm dominant wavelength [3] ? d 560 nm measured at peak spectral line half width ?? 1/2 24 nm p605/q600 speed of response ? s 3100 ns capacitance c 35 pf v f = 0; f = 1 mhz thermal resistance r ? j-pin 170 c/w junction-to-cathode lead luminous effi cacy [4] ? v 656 lm/w note: 1. please refer to application note 1061 for information comparing standard green and emerald green light output degradation.
12 standard red, dh as algaas red standard red and dh as algaas red high effi ciency red, orange, yellow, high performance green, and emerald green her, orange, yellow, and high performance green, and emerald green low current figure 1. relative intensity vs. wavelength. figure 2. forward current vs. forward voltage (non-resistor lamp). figure 3. relative luminous intensity vs. forward current (non-resistor lamp). forward current ?ma 100 0 forward voltage ?v 80 60 50 70 20 0 10 30 40 0.5 1 1.5 2 2.5 3 3.5 90 high performance green, emerald green yellow high efficiency red/orange
13 figure 4. relative effi ciency (luminous intensity per unit current) vs. peak current (non-resistor lamps). figure 5. maximum forward dc current vs. ambient temperature. derating based on t j max = 110c (non-resistor lamps). figure 6. maximum tolerable peak current vs. pulse duration (i dc max as per max ratings) (non-resistor lamps). standard red dh as algaas red standard red her, orange, yellow, and high performance green dh as algaas red her, orange, yellow, and high performance green, and emerald green
14 figure 9. relative intensity vs. angular displacement. figure 7. resistor lamp forward current vs. forward v oltage. figure 8. resistor lamp luminous intensity vs. forward voltage.
15 intensity bin limits bin min. max. a 0.10 0.20 b 0.16 0.32 c 0.25 0.50 d 0.40 0.80 e 0.63 1.25 f 1.00 2.00 g 1.60 3.20 h 2.50 5.00 j 4.00 8.00 k 6.30 12.50 l 10.00 20.00 m 16.00 32.00 n 25.00 50.00 p 40.00 80.00 q 63.00 125.00 r 100.00 200.00 s 160.00 320.00 t 250.00 500.00 u 400.00 800.00 v 630.00 1250.00 w 1000.00 2000.00 x 1600.00 3200.00 y 2500.00 5000.00 color bin limits package bin min. max. emerald green 0 full distribution 9 552 556 8 555 559 7 558 562 6 561 565 green 0 full distribution 6 561 565 5 564 568 4 567 571 3 570 574 2 573 577 yellow 0 full distribution 1 581.5 585.0 3 584.0 587.5 2 586.5 590.0 4 589.0 592.5 5 591.5 593.5 6 591.5 595.0 7 594.0 597.5 orange 0 full distribution 1 596.5 600.0 2 599.0 602.5 3 601.5 604.0 4 603.8 608.2 5 606.8 611.2 6 609.8 614.2 7 612.8 617.2 8 615.8 620.2 ordering information hlmx- xxxx-x x x x x 4 x 4 prod. part number min. iv bin max. iv bin color bin selection packaging option
mechanical option 00 straight leads, bulk packaging, quantity of 500 parts 10 right angle housing, bulk packaging, quantity of 500 parts 11 gull wing leads, 12 mm tape on 7 in. dia. reel, 1500 parts per reel 12 gull wing lead, bulk packaging, quantity of 500 parts 14 gull wing leads, 12 mm tape on 13 in. dia. reel, 6000 parts per reel 21 yoke leads, 12 mm tape on 7 in. dia. reel, 1500 parts per reel 22 yoke leads, bulk packaging, quantity of 500 parts 24 yoke leads, 12 mm tape on 13 in. dia. reel, 6000 parts per reel 31 z-bend leads, 12 mm tape on 7 in. dia. reel, 1500 parts per reel 32 z-bend leads, bulk packaging, quantity of 500 parts 34 z-bend leads, 12 mm tape on 13 in. dia. reel, 6000 parts per reel 1l 2.54 mm (0.100 inch) center lead spacing, long leads; 10.4 mm (0.410 in.) 1s 2.54 mm (0.100 inch) center lead spacing, short leads; 3.7 mm (0.145 in.) 2l 5.08 mm (0.200 inch) center lead spacing, long leads; 10.4 mm (0.410 in.) 2s 5.08 mm (0.200 inch) center lead spacing, short leads; 3.7 mm (0.145 in.) note: all categories are established for classifi cation of products. products may not be available in all categories. please contact your local avago represen- tative for further clarifi cation/information. for product information and a complete list of distributors, please go to our web site: www.avagotech.com avago, avago technologies, and the a logo are trademarks of avago technologies in the united states and other countries. data subject to change. copyright ? 2005-2012 avago technologies. all rights reserved. obsoletes 5989-1708en av02-3609en - june 12, 2012

▲Up To Search▲

Price & Availability of HLMP-6620-F001S

	To Download HLMP-6620-F001S Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .