View LP156WH1-TLB1_6581602.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

product specification 1/ 31 lp156wh1 liquid crystal display ver. 0.3 aug. 08, 2008 specification for approval 15.6? hd tft lcd title model dell customer *when you obtain standard approval, please use the above model name without suffix lp156wh1 *model tlb1 suffix lg.philips lcd co., ltd. supplier ) ) ( ( final specification preliminary specification please return 1 copy for your confirmation with your signature and comments. / / / signature approved by prepared by reviewed by signature approved by k. s. kwon / s.manager j. h. park / manager prepared by reviewed by signature approved by k. s. kwon / s.manager j. h. park / manager b. t. jang / engineer s. h. ahn / engineer products engineering dept. lg display co., ltd www.datasheet.net/ datasheet pdf - http://www..co.kr/
product specification 2/ 31 lp156wh1 liquid crystal display ver. 0.3 aug. 08, 2008 contents 21-23 appendix. lpl proposal for system cover design a 9-10 lvds signal timing specification 3-3 29-31 appendix. enhanced extended display identification data a 27-28 precautions 9 12 8 interface connections 3-2 color input data refernece 3-5 26 designation of lot mark 8-1 26 packing form 8-2 packing 8 25 emc 7-2 1 cover 2 contents 3 record of revisions 4 general description 1 5 absolute maximum ratings 2 electrical specifications 3 6-7 electrical charactreistics 3-1 11 signal timing specifications 3-3 11 signal timing waveforms 3-4 13 power sequence 3-6 14-16 optical sfecifications 4 17-20 mechanical characteristics 5 24 reliablity 6 international standards 7 25 safety 7-1 page item no www.datasheet.net/ datasheet pdf - http://www..co.kr/
product specification 3/ 31 lp156wh1 liquid crystal display ver. 0.3 aug. 08, 2008 record of revisions 0.0 change rear view drawing (label modification) 19 jul. 11. 2008 0.1 0.0 change rear view drawing (label modification) change source cover shield (printed) 19 jul. 24. 2008 0.2 change edid data 29-31 0.1 add color coordinate specification 14 aug. 08. 2008 0.3 0.0 edid ver first draft (preliminary specification) - jun. 07. 2008 0.0 description page revision date revision no www.datasheet.net/ datasheet pdf - http://www..co.kr/
product specification 4/ 31 lp156wh1 liquid crystal display ver. 0.3 aug. 08, 2008 1. general description general features hard coating(3h), anti-glare treatment of the front polarizer surface treatment 6-bit, 262,144 colors color depth 1366 horiz. by 768 vert. pixels rgb strip arrangement pixel format 220 cd/m 2 (typ.5 point) luminance, white total 5.75 watt(typ.) @ lcm circuit 1. 3 watt(typ.), b/l input 4.45 watt(typ.) power consumption 550g (max.) weight transmissive mode, normally white display operating mode yes rohs comply 0.252mm 0.252 mm pixel pitch 359.3(h, typ) 209.5(v, typ) 6.4(d,max) [mm] outline dimension 15.6 inches diagonal active screen size the lp156wh1 is a color active matrix liquid crystal display with an integral cold cathode fluorescent lamp (ccfl) backlight system. the matrix employs a-si thin film transistor as the active element. it is a transmissive type display operating in the normally white mode. this tft-lcd has 15.6 inches diagonally measured active display area with hd resolution(768 vertical by 1366 horizontal pixel array). each pixel is divided into red, green and blue sub-pixels or dots which are arranged in vertical stripes. gray scale or the brightness of the sub-pixel color is determined with a 6-bit gray scale signal for each dot, thus, presenting a palette of more than 262,144 colors. the lp156wh1 has been designed to apply the interface method that enables low power, high speed, low emi. the lp156wh1 is intended to support applications where thin thickness, low power are critical factors and graphic displays are important. in combination with the vertical arrangement of the sub-pixels, the lp156wh1 characteristics provide an excellent flat display for office automation products such as notebook pc. control & data power edid signal & power tft-lcd panel (1366 x 768) 1 768 1 1366 cn 1 user connector 30 pin power block edid block gip(gate in panel) source driver circuit backlight ass ? y cn lvds & timing control block www.datasheet.net/ datasheet pdf - http://www..co.kr/
product specification 5/ 31 lp156wh1 liquid crystal display ver. 0.3 aug. 08, 2008 2. absolute maximum ratings the following are maximum values which, if exceeded, may cause faulty operation or damage to the unit. table 1. absolute maximum ratings storage operation 10 20 30 40 50 60 70 80 0 -20 dry bulb temperature [ ] 10 % 20 % 40 % 60 % 90% 80% 0 10 20 30 40 50 60 wet bulb temperature [ ] humidity[(%)rh] units 1 %rh 90 10 h op operating ambient humidity 1 %rh 90 10 h st storage humidity 1 c 60 -20 h st storage temperature 1 c 50 0 t op operating temperature at 25 5 c vdc 4.0 -0.3 vcc power input voltage max min parameter notes values symbol note : 1. temperature and relative humidi ty range are shown in the figure below. wet bulb temperature should be 39 c max, and no condensation of water. www.datasheet.net/ datasheet pdf - http://www..co.kr/
product specification 6/ 31 lp156wh1 liquid crystal display ver. 0.3 aug. 08, 2008 3. electrical specifications 3-1. electrical characteristics the lp156wh1 requires two power inputs. one is employed to power the lcd electronics and to drive the tft array and liquid crystal. the second input which powers the ccfl, is typically generated by an inverter. the inverter is an external unit to the lcd. table 2. electrical characteristics 1 ma 455 390 - 1 watt 1.5 1.3 - pc power consumption 4.9 4.45 - p bl power consumption v rms v rms 1300 1500 vs established starting voltage at 25 at 0 lamp : v rms 870(3.0ma) 685(6.5ma) 660(7.0ma) v bl operating voltage 3 ma rms 7.0 6.5 3.0 i bl operating current khz 70 60 40 f bl operating frequency 4 min 3 - - ts discharge stabilization time 5 hrs - - 15,000 life time 2 ohm 110 100 90 zm differential impedance v dc 3.6 3.3 3.0 vcc power supply input voltage i cc power supply input current module : parameter symbol max typ min notes unit values note) 1. the specified current and power consumption are under the vcc = 3.3v , 25 , fv = 60hz condition whereas mosaic pattern is displayed and fv is the frame frequency. 2. this impedance value is needed to proper display and measured form lvds tx to the mating connector. 3. the typical operating current is for the typica l surface luminance (lwh) in optical characteristics. 4. define the brightness of the lamp after being ligh ted for 5 minutes as 100%, ts is the time required for the brightness of the center of t he lamp to be not less than 95%. www.datasheet.net/ datasheet pdf - http://www..co.kr/
product specification 7/ 31 lp156wh1 liquid crystal display ver. 0.3 aug. 08, 2008 i p i -p * asymmetry rate: | i p ?i ?p | / i rms * 100% * distortion rate i p (or i ?p ) / i rms normal current wave -standard abnormal current wave -bad abnormal current wave -bad abnormal current wave -bad note) 5. the life time is determined as the time at which brightness of lamp is 50% compare to that of initial value at the typical lamp current. 6. the output of the inverter must have symmetrical(negative and positive) voltage waveform and symmetrical current waveform.(asymmetrical ratio is less than 10%) please do not use the inverter which has asymmetrical voltage and asymmetrical current and spike wave. lamp frequency may produce interface with horizontal synchronous frequency and as a result this may cause beat on the display. therefore lamp frequency shall be as away possible from the horizontal synchronous frequency and from its harmonics in order to prevent interference. 7. it is defined the brightness of the lamp after being lighted for 5 minutes as 100%. t s is the time required for the brightness of the center of the lamp to be not less than 95%. 8. the lamp power consumption shown above does not include loss of external inverter. the applied lamp current is a typical one. 9. requirements for a system inverter design, which is intended to have a better display performance, a better power efficiency and a more reliable lamp, are following. it shall help increase the lamp lifetime and reduce leakage current. a. the asymmetry rate of the inverter waveform should be less than 10%. b. the distortion rate of the waveform should be within 2 10%. * inverter output waveform had better be more similar to ideal sine wave. 10. inverter open voltage must be more than lamp voltage for more than 1 second for start-up. otherwise, the lamps may not be turned on. do not attach a conducting tape to lamp connecting wire. if the lamp wire attach to a conducting tape, tft-lcd module has a low luminance and the inverter has abnormal action. because leakage current is occurred between lamp wire and conducting tape. ex of current wave) www.datasheet.net/ datasheet pdf - http://www..co.kr/
product specification 8/ 31 lp156wh1 liquid crystal display ver. 0.3 aug. 08, 2008 3-2. interface connections table 3. module connector pin configuration (cn1) no connection nc 20 ground gnd 19 positive lvds differential clock input odd_clkin+ 18 negative lvds differential clock input odd_clkin- 17 ground gnd 16 positive lvds differential data input odd_r in 2+ 15 negative lvds differential data input odd_r in 2- 14 ground gnd 13 positive lvds differential data input odd_r in 1+ 12 negative lvds differential data input odd_r in 1- 11 no connection nc 30 power supply, 3.3v typ. vcc 2 power supply, 3.3v typ. vcc 3 ddc 3.3v power v eedid 4 built-in self test bist 5 ddc clock clk eedid 6 ddc data data eedid 7 positive lvds differential data input odd_r in 0+ 9 ground gnd 1 negative lvds differential data input odd_r in 0- 8 ground gnd 10 no connection nc 22 no connection nc 23 no connection nc 24 no connection nc 25 no connection nc 26 no connection nc 27 no connection nc 28 no connection nc 29 notes description symbol pin nc no connection 21 1, interface chips 1.1 lcd : sw, sw0624 (lcd controller) including lvds receiver 1.2 system : thc63lvdf823a or equivalent * pin to pin compatible with lvds 2. connector 2.1 lcd :fi-xb30srl-hf11 ,jae or its compatibles 2.2 mating : fi-x30m or equivalent. 2.3 connector pin arrangement 1 30 [lcd module rear view] this lcd employs two interface connections, a 30 pin c onnector is used for the module electronics interface and the other connector is used for the integral backlight system. the electronics interface connector is a m odel fi-xb30srl-hf11 manufactured by jae. the backlight interface connector is a model bhsr-02vs-1, manufactured by jst or compatible. the mating connector part number is amp1674817-2 or equivalent. notes : 1. the high voltage side terminal is colored pink and the low voltage side terminal is green. pin2 pin2 pin1 1 power supply for lamp (low voltage side) lv 2 1 power supply for lamp (high voltage side) hv 1 notes description symbol pin table 4. backlight connector pin configuration (j3) www.datasheet.net/ datasheet pdf - http://www..co.kr/
product specification 9/ 31 lp156wh1 liquid crystal display ver. 0.3 aug. 08, 2008 notes unit max min symbol description 85mhz > fclk 65mhz ps + 400 - 400 t skew lvds clock to data skew margin - - - 65mhz > fclk 25mhz % 3 - f dev maximum deviation of input clock frequency during ssc khz 200 - f mod maximum modulation frequency of input clock during ssc -1/7 - 600 t clk + 1/7 t skew_eo lvds clock to clock skew margin (even to odd) ps + 600 t skew - v 2.1 0.3 v in lvds input voltage range - v 1.8 0.6 v cm lvds common mode voltage - mv 600 100 |v id | lvds differential voltage notes unit max min symb ol description 3-3-1. dc specification 3-3-2. ac specification 3-3. lvds signal timing specifications www.datasheet.net/ datasheet pdf - http://www..co.kr/
product specification 10 / 31 lp156wh1 liquid crystal display ver. 0.3 aug. 08, 2008 < clock skew margin between channel > < lvds data format > 3-3-3. data format 1) lvds 1 port < spread spectrum > time f center f max f min f mod 1 f center * f dev freq. g0 r5 r4 r3 r2 r1 r0 b1 b0 g5 g4 g3 g2 g1 de vsync hsync b5 b4 b3 b2 x b7 b6 g7 g6 r7 r6 r1 r0 g2 g1 b3 b2 r7 r6 g0 b1 de x current (nth ) cycle r5 r4 b0 g5 vsync hsync b7 b6 r3 r2 g4 g3 b5 b4 g7 g6 previous (n-1)th cycle next (n+1)th cycle rclk+ ra+/- rb+/- rc+/- rd+/- www.datasheet.net/ datasheet pdf - http://www..co.kr/
product specification 11 / 31 lp156wh1 liquid crystal display ver. 0.3 aug. 08, 2008 3-4. signal timing specifications table 6. timing table this is the signal timing required at the input of the us er connector. all of the interface signal timing should be satisfied with the following specifications and spec ifications of lvds tx/rx for its proper operation. 3-5. signal timing waveforms condition : vcc =3.3v low: 0.3vcc high: 0.7vcc data enable, hsync, vsync hsync data enable vsync data enable t wh t hp t hfp t hbp t vp t wv t vbp t vfp t wha t wva t clk 0.5 vcc dclk 768 768 768 t wva width-active 1366 1366 1366 t wha width-active tclk 124 80 72 t hbp horizontal back porch 48 48 8 t hfp horizontal front porch thp 20 14 8 t vbp vertical back porch 5 3 1 t vfp vertical front porch thp 801 790 779 t vp period 8 5 2 t wv width 40 32 23 t wh width tclk 1586 1526 1470 t hp period hsync vsync data enable mhz - 72.3 - f clk frequency dclk note unit max typ min symbol item www.datasheet.net/ datasheet pdf - http://www..co.kr/
product specification 12 / 31 lp156wh1 liquid crystal display ver. 0.3 aug. 08, 2008 3-6. color input data reference the brightness of each primary color (red,green and blue) is based on the 6-bit gray scale data input for the color ; the higher the binary input, the brighter the color. the table below provides a reference for color versus data input. table 7. color data reference 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green (00) green 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 green (01) ? ? ? ... 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 0 green (62) 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 green (63) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red (00) red 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 red (01) ? ? ? ? 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0 red (62) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 red (63) 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 blue (01) ? ? ? ? 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 blue (62) 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 blue (63) blue (00) white yellow magenta cyan blue green red black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 basic color 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 blue msb lsb green msb lsb red msb lsb b5 b4 b3 b2 b1 b0 g5 g4 g3 g2 g1 g0 r5 r4 r3 r2 r1 r0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 blue color input color data www.datasheet.net/ datasheet pdf - http://www..co.kr/
product specification 13 / 31 lp156wh1 liquid crystal display ver. 0.3 aug. 08, 2008 3-7. power sequence note) 1. valid data is data to meet ?3-3. lvds signal timing specifications? 2. please avoid floating state of interface signal at invalid period. 3. when the interface signal is invalid, be sure to pull down the power supply for lcd vcc to 0v. 4. lamp power must be turn on after power supply for lcd and interface signal are valid. (ms) - - 400 t 7 (ms) 10 - 3 t 6 (ms) 50 - 0 t 5 (ms) - - 200 t 4 (ms) - - 200 t 3 (ms) 50 - 0 t 2 (ms) 10 - 0 t 1 max. typ. min. units value parameter table 8. power sequence table t 6 interface signal, v i (lvds signal of transmitter) lamp power power supply for lcd vcc 90% 10% 10% 0v 90% t 1 t 2 t 5 valid data 0v off off lamp on t 7 t 3 t 4 www.datasheet.net/ datasheet pdf - http://www..co.kr/
product specification 14 / 31 lp156wh1 liquid crystal display ver. 0.3 aug. 08, 2008 4. optical specification fig. 1 optical characteristic measurement equipment and method table 9. optical characteristics ta=25 c, vcc=3.3v, f v =60hz, f clk = 72.3mhz, f bl = 60khz , i bl = 6.5ma 5 viewing angle color coordinates 4 ms 25 16 - tr r + tr d response time 0.133 0.103 0.073 by 0.343 0.313 0.283 wx white y axis, down ( =270 ) y axis, up ( =90 ) x axis, left ( =180 ) x axis, right( =0 ) degree - - 40 r degree - - 40 l degree - - 15 u degree - - 30 d blue 0.359 0.329 0.299 wy 6 gray scale green red 0.313 0.283 0.253 gx 0.616 0.586 0.556 gy 0.638 0.608 0.578 rx 0.368 0.338 0.308 ry 3 1.6 1.4 - white luminance variation 0.180 0.150 0.120 bx max typ min 1 - - 400 cr contrast ratio 2 cd/m 2 - 220 200 l wh surface luminance, white parameter symbol notes units values lcd module optical stage(x,y) pritchard 880 or equivalent 50cm optical characteristics are determined after the unit has been ?on? and stable for approximately 30 minutes in a dark environment at 25 c . the values specified are at an approximate distance 50cm from the lcd surface at a viewing angle of and equal to 0 . fig. 1 presents additional information conc erning the measurement equipment and method. www.datasheet.net/ datasheet pdf - http://www..co.kr/
product specification 15 / 31 lp156wh1 liquid crystal display ver. 0.3 aug. 08, 2008 100 l63 74.2 l55 12.2 l23 21.0 l31 34.8 l39 52.5 l47 5.4 l15 1.5 l7 0 l0 luminance [%] (typ) gray level note) 1. contrast ratio(cr) is defined mathematically as surface luminance with all white pixels contrast ratio = surface luminance with all black pixels 2. surface luminance is the average of 5 point across the lcd surface 50cm from the surface with all pixels displaying white. for more information see fig 1. l wh = average(l 1 ,l 2 , ? l 5 ) 3. the variation in surface luminance , the panel total variation ( white ) is determined by measuring l n at each test position 1 through 13 and then defined as followed numerical formula. for more information see fig 2. maximum(l 1 ,l 2 , ? l 13 ) white = minimum(l 1 ,l 2 , ? l 13 ) 4. response time is the time required for the display to transition from white to black (rise time, tr r ) and from black to white(decay time, tr d ). for additional information see fig 3. 5. viewing angle is the angle at which the contra st ratio is greater than 10. the angles are determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the lcd surface. for more information see fig 4. 6. gray scale specification * f v = 60hz www.datasheet.net/ datasheet pdf - http://www..co.kr/
product specification 16 / 31 lp156wh1 liquid crystal display ver. 0.3 aug. 08, 2008 fig. 4 viewing angle normal y eye = 0 , right = 180 , left = 270 , down = 90 , up fig. 3 response time the response time is defined as the following figure and shall be measured by switching the input signal for ?black? and ?white?. tr r tr d 100 90 10 0 % optical response white black white : active area a : h/4 mm b: v/4 mm points: 13 points h,v active area 1 3 2 5 4 h a b v 678 910 11 12 13 10mm 10mm fig. 2 luminance www.datasheet.net/ datasheet pdf - http://www..co.kr/
product specification 17 / 31 lp156wh1 liquid crystal display ver. 0.3 aug. 08, 2008 5. mechanical characteristics the contents provide general mechanical characteristic s for the model lp156wh1. in addition the figures in the next page are detailed mechanical drawing of the lcd. 193.536 mm vertical hard coating(3h), anti-glare treatment of the front polarizer surface treatment 550g (max.) weight 197.1 0.5mm vertical 209.5 0.5mm vertical 6.4mm (max) thickness 344.232 mm horizontal active display area 349.8 0.5mm horizontal bezel area 359.3 0.5mm horizontal outline dimension www.datasheet.net/ datasheet pdf - http://www..co.kr/
product specification 18 / 31 lp156wh1 liquid crystal display ver. 0.3 aug. 08, 2008 note) unit:[mm], general tolerance: 0.5mm www.datasheet.net/ datasheet pdf - http://www..co.kr/
product specification 19 / 31 lp156wh1 liquid crystal display ver. 0.3 aug. 08, 2008 note) unit:[mm], general tolerance: 0.5mm www.datasheet.net/ datasheet pdf - http://www..co.kr/
product specification 20 / 31 lp156wh1 liquid crystal display ver. 0.3 aug. 08, 2008 [ detail description of side mounting screw ] notes : 1. screw plated through the method of non-electrolytic nickel plating is preferred to reduce possibility that results in vertical and/or horizontal line defect due to the conductive particles from screw surface. * mounting screw length (a) = 2.0(min) / 2.5(max) * mounting screw hole depth (b) = 2.5(min) * mounting hole location : 3.70(typ.) * torque : 2.0 kgf.cm(max) (measurement gauge : torque meter) www.datasheet.net/ datasheet pdf - http://www..co.kr/
product specification 21 / 31 lp156wh1 liquid crystal display ver. 0.3 aug. 08, 2008 lpl proposal for system cover design.(appendix) define define 1. rear side of lcm is sensitive agains t external stress,and previous check about interference is highly needed. 2.in case there is something from system cover comes into the boundary above,mechanical interference may cause the fos defects. (eg:ripple,white spot..) check if antenna cable is sufficiently apart from t-co n of lcd module. 2 1 gap check for securing t he enough gap between lcm and system cover. no good good 1.if system antenna is overlapped with t-con,it might be cause the noise. www.datasheet.net/ datasheet pdf - http://www..co.kr/
product specification 22 / 31 lp156wh1 liquid crystal display ver. 0.3 aug. 08, 2008 lpl proposal for system cover design. 1.cof area needs to be handled with care. define 1 .at least 2.0mm of gap needs to be secured to prevent the shock related defects. define 2.?l? type of hinge is recommend ed than ?i? type under shock test. 2.good ? wire path design to system side. ok ? wire path is located between cofs. bad ? wire path overlapped with cof area. 4 3 gap check for securing the enough gap between lcm and system hinge. checking the path of the system wire. #1 #2 #3 #4 #5 #6 ok bad good www.datasheet.net/ datasheet pdf - http://www..co.kr/
product specification 23 / 31 lp156wh1 liquid crystal display ver. 0.3 aug. 08, 2008 lpl proposal for system cover design. 1.cnt area is specially sensitive against external stress,and ad ditional gap by cutting on system cover will be helpful on removing the ripple. 2.using a thinner cnt will be better. (eg: fpc type) define 1.condition without bracke t is good for mechanical noise,and can minimize the light leakage from deformation of bracket. define 2.the results shows that there is no difference between the condition with or without bracket. securing additional gap on cnt area.. 6 5 using a bracket on the top of lcm is not recommended. with bracket without bracket bracket user connector cable pathway. system cover inner side. user connector area. fpc:flexible printed circuit. cut a a-1 a~a-1 www.datasheet.net/ datasheet pdf - http://www..co.kr/
product specification 24 / 31 lp156wh1 liquid crystal display ver. 0.3 aug. 08, 2008 6. reliability environment test condition { result evaluation criteria } there should be no change which might affect the practical display function when the display quality test is conducted under normal operating condition. 0 ~ 10,000 feet (3,048m) 24hr 0 ~ 40,000 feet (12,192m) 24hr altitude operating storage / shipment 7 half sine wave, 180g, 2ms one shock of each six faces(i.e. run 180g 2ms for all six faces) shock test (non-operating) 6 sine wave, 10 ~ 500 ~ 10hz, 1.5g, 0.37oct/min 3 axis, 1hour/axis vibration test (non-operating) 5 ta= 0 c, 240h low temperature operation test 4 ta= 50 c, 50%rh, 240h high temperature operation test 3 ta= -20 c, 240h low temperature storage test 2 ta= 60 c, 240h high temperature storage test 1 conditions test item no. www.datasheet.net/ datasheet pdf - http://www..co.kr/
product specification 25 / 31 lp156wh1 liquid crystal display ver. 0.3 aug. 08, 2008 7. international standards 7-1. safety 7-2. emc a) ansi c63.4 ?methods of measurement of radio- noise emissions from low-voltage electrical and electrical equipment in the range of 9khz to 40ghz. ?american national standards institute(ansi), 1992 b) c.i.s.p.r ?limits and met hods of measurement of radio interf ace characteristics of information technology equipment.? international special committee on radio interference. c) en 55022 ?limits and methods of measurement of radio interface characteristics of information technology equipment.? european committee for electrotechnical standardization.(cenelec), 1998 ( including a1: 2000 ) a) ul 60950-1:2003, first edition, underwriters laboratories, inc., standard for safety of information technology equipment. b) can/csa c22.2, no. 60950-1-03 1 st ed. april 1, 2003, canadian standards association, standard for safety of information technology equipment. c) en 60950-1:2001, first edition, european committee for electrotechnical standardization(cenelec) european standard for safety of information technology equipment. www.datasheet.net/ datasheet pdf - http://www..co.kr/
product specification 26 / 31 lp156wh1 liquid crystal display ver. 0.3 aug. 08, 2008 8. packing 8-2. packing form a) package quantity in one box : 20 pcs b) box size : 472 mm 380 mm 257 mm 8-1. designation of lot mark a) lot mark abcdefghi jklm a,b,c : size(inch) d : year e : month f ~ m : serial no. note 1. year 2. month mark year 0 2010 6 2006 7 2007 8 2008 9 2009 4 2004 5 2005 3 2 1 2003 2002 2001 b nov mark month a oct 6 jun 7 jul 8 aug 9 sep 4 apr 5 may c 3 2 1 dec mar feb jan b) location of lot mark serial no. is printed on the label. the label is attached to the backside of the lcd module. this is subject to change without prior notice. www.datasheet.net/ datasheet pdf - http://www..co.kr/
product specification 27 / 31 lp156wh1 liquid crystal display ver. 0.3 aug. 08, 2008 9. precautions please pay attention to the followings when you use this tft lcd module. 9-1. mo unting precautions (1) you must mount a module using holes arranged in four corners or four sides. (2) you should consider the mounting structure so that uneven force (ex. twisted stress) is not applied to the module. and the case on which a module is mounted s hould have sufficient strength so that external force is not transmitted directly to the module. (3) please attach the surface transparent protective plat e to the surface in order to protect the polarizer. transparent protective plate should have sufficient strength in order to the resist external force. (4) you should adopt radiation structure to satisfy the temperature specification. (5) acetic acid type and chlorine type materials for the cover case are not desirable because the former generates corrosive gas of attacking the polarizer at high temperature and the latter causes circuit break by electro-chemical reaction. (6) do not touch, push or rub the exposed polarizers with glass, tweezers or anything harder than hb pencil lead. and please do not rub with dust clothes with chemical treatment. do not touch the surface of polarizer for bare hand or greasy cloth.(some cosmetics are detrimental to the polarizer.) (7) when the surface becomes dusty, please wipe gently wi th absorbent cotton or other soft materials like chamois soaks with petroleum benzene. normal-hexane is recommended for cleaning the adhesives used to attach front / rear polarizers. do not use acetone, toluene and alcohol because they cause chemical damage to the polarizer. (8) wipe off saliva or water drops as soon as possib le. their long time contact with polarizer causes deformations and color fading. (9) do not open the case because inside circuits do not have sufficient strength. 9-2. operating precautions (1) the spike noise causes the mis-operation of circuits. it should be lower than following voltage : v= 200mv(over and under shoot voltage) (2) response time depends on the temperature.(in lower temperature, it becomes longer.) (3) brightness depends on the temperature. (in lower temperature, it becomes lower.) and in lower temperature, response time(required time that brightness is stable after turned on) becomes longer. (4) be careful for condensation at sudden temperatur e change. condensation makes damage to polarizer or electrical contacted parts. and after fadi ng condensation, smear or spot will occur. (5) when fixed patterns are displayed for a l ong time, remnant image is likely to occur. (6) module has high frequency circuits. sufficient suppression to the electromagnetic interference shall be done by system manufacturers. grounding and shielding methods may be important to minimized the interference. www.datasheet.net/ datasheet pdf - http://www..co.kr/
product specification 28 / 31 lp156wh1 liquid crystal display ver. 0.3 aug. 08, 2008 since a module is composed of electronic circuits, it is not strong to electrostatic discharge. make certain that treatment persons are connected to ground through wris t band etc. and don?t touch interface pin directly. 9-3. electrostatic discharge control strong light exposure causes degradation of polarizer and color filter. 9-4. precautions for strong light exposure 9-5. storage (1) when the protection film is peeled off, static el ectricity is generated between the film and polarizer. this should be peeled off slowly and carefully by people who are electrically grounded and with well ion-blown equipment or in such a condition, etc. (2) the protection film is attached to the polarizer with a small amount of glue. if some stress is applied to rub the protection film against the polarizer during the time you peel off the film, the glue is apt to remain on the polarizer. please carefully peel off the protection film without rubbing it against the polarizer. (3) when the module with protection film attached is stored for a long time, sometimes there remains a very small amount of glue still on the polarize r after the protection film is peeled off. (4) you can remove the glue easily. when the glue remains on the polarizer surface or its vestige is recognized, please wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal-hexane. 9-6. handling precaution s for protection film when storing modules as spares for a long time, the following precautions are necessary. (1) store them in a dark place. do not expose the module to sunlight or fluorescent light. keep the temperature between 5 c and 35 c at normal humidity. (2) the polarizer surface should not come in contact with any other object. it is recommended that they be stored in the container in which they were shipped. www.datasheet.net/ datasheet pdf - http://www..co.kr/
product specification 29 / 31 lp156wh1 liquid crystal display ver. 0.3 aug. 08, 2008 appendix a. enhanced extended di splay identification data (eedid tm ) 1/3 byte# byte# (deci mal ) (h e x ) 000header 0 0 0000 0000 101header f f 1111 1111 202header f f 1111 1111 303header f f 1111 1111 header 404header f f 1111 1111 505header f f 1111 1111 606header f f 1111 1111 707header 0 0 0000 0000 808ei sa m anufacturer code(3 c haracter i d) = lgd 3 0 0011 0000 9 09 c om pressed asc i i e 4 1110 0100 10 0a product code = 018a 0 1 0000 0001 11 0b (h ex, lsb fi rs t) 8 a 1000 1010 12 0c lc d m odul e seri al no - preferred but o pti onal ( 0 i f not used) 0 0 0000 0000 vender/ 13 0d lc d m odul e seri al no - preferred but o pti onal ( 0 i f not used) 0 0 0000 0000 product i d 14 0e lc d m odul e seri al no - preferred but o pti onal ( 0 i f not used) 0 0 0000 0000 15 0f lc d m odul e seri al no - preferred but o pti onal ( 0 i f not used) 0 0 0000 0000 16 10 w eek of m anufacture 0 0 0000 0000 17 11 year of m anufacture = 2008 1 2 0001 0010 18 12 ed i d structure versi o n # = 1 0 1 0000 0001 edi d versi on/ 19 13 ed i d revi si o n # = 3 0 3 0000 0011 revi si on 20 14 vi deo i nput d efi ni ti o n = d i gi ta l i /p ,n o n t m d s c r g b 8 0 1000 0000 21 15 m ax h i mage si ze(M)=34.4232cm (34) 2 2 0010 0010 di spl ay 22 16 m ax v i mage si ze(M)=19.3536cm (19) 1 3 0001 0011 param eter 23 17 d i spl ay gam m a =2.2 7 8 0111 1000 24 18 feature support(d pm s) = acti ve o ff, r g b c o l or 0 a 0000 1010 25 19 red/g reen l ow bi ts e 8 1110 1000 26 1a bl ue/w hi te l o w b i ts 9 5 1001 0101 2 7 1 b r e d x = 0 .6 0 8 9 b 1001 1011 2 8 1 c r e d y = 0 .3 3 8 5 6 0101 0110 29 1d g reen x = 0.283 4 8 0100 1000 col or 30 1e g reen y = 0.586 9 6 1001 0110 c haracteri sti c 31 1f bl u e x = 0 .1 5 0 2 6 0010 0110 32 20 bl u e y = 0 .1 0 3 1 a 0001 1010 33 21 w hi te x = 0.313 5 0 0101 0000 34 22 w hi te y = 0.329 5 4 0101 0100 35 23 establ i shed ti mi ng i = 0 0 h (i f n o t u s e d ) 0 0 0000 0000 establ i shed 36 24 establ i shed ti mi ng i i = 0 0 h (i f not used) 0 0 0000 0000 ti mi ngs 37 25 m anufacturer's ti mi ngs = 00h(i f not used) 0 0 0000 0000 38 26 standard ti mi ng i denti fi cati o n 1 w a s n o t u s e d 0 1 0000 0001 39 27 standard ti mi ng i denti fi cati o n 1 w a s n o t u s e d 0 1 0000 0001 40 28 standard ti mi ng i denti fi cati o n 2 w a s n o t u s e d 0 1 0000 0001 41 29 standard ti mi ng i denti fi cati o n 2 w a s n o t u s e d 0 1 0000 0001 42 2a standard ti mi ng i denti fi cati o n 3 w a s n o t u s e d 0 1 0000 0001 43 2b standard ti mi ng i denti fi cati o n 3 w a s n o t u s e d 0 1 0000 0001 44 2c standard ti mi ng i denti fi cati o n 4 w a s n o t u s e d 0 1 0000 0001 standard 45 2d standard ti mi ng i denti fi cati o n 4 w a s n o t u s e d 0 1 0000 0001 ti mi ng i d 46 2e standard ti mi ng i denti fi cati o n 5 w a s n o t u s e d 0 1 0000 0001 47 2f standard ti mi ng i denti fi cati o n 5 w a s n o t u s e d 0 1 0000 0001 48 30 standard ti mi ng i denti fi cati o n 6 w a s n o t u s e d 0 1 0000 0001 49 31 standard ti mi ng i denti fi cati o n 6 w a s n o t u s e d 0 1 0000 0001 50 32 standard ti mi ng i denti fi cati o n 7 w a s n o t u s e d 0 1 0000 0001 51 33 standard ti mi ng i denti fi cati o n 7 w a s n o t u s e d 0 1 0000 0001 52 34 standard ti mi ng i denti fi cati o n 8 w a s n o t u s e d 0 1 0000 0001 53 35 standard ti mi ng i denti fi cati o n 8 w a s n o t u s e d 0 1 0000 0001 fi el d n a m e a n d c o m m e n ts val ue (h e x ) val ue (b i nary) www.datasheet.net/ datasheet pdf - http://www..co.kr/
product specification 30 / 31 lp156wh1 liquid crystal display ver. 0.3 aug. 08, 2008 appendix a. enhanced extended di splay identification data (eedid tm ) 2/3 byte# byte# (d e c i mal ) (h e x ) 54 36 1366x768 @ 60? m ode pi xel c l ock (lsb) => 72.3m h z 3 e 0011 1110 55 37 (stored lsb fi rst) 1 c 0001 1100 56 38 h ori zo ntal a c ti ve = 1366 pi xel s (l ow er 8bi ts) 5 6 0101 0110 57 39 h ori zo ntal b l anki n g = 1 6 0 p i xel s (l ow er 8bi ts) a 0 1010 0000 58 3a h ori zo ntal a c ti ve : h o ri zo ntal b l anki ng (upper 4:4bi ts) 5 0 0101 0000 59 3b verti cal a v ti v e = 7 6 8 l i n e s (l ow er 8bi ts) 0 0 0000 0000 60 3c verti cal b l anki n g = 2 2 l i n e s (l ow er 8bi ts) 1 6 0001 0110 61 3d verti cal a c ti v e : v e rti cal b l anki n g (u p p e r 4 :4 b i ts) 3 0 0011 0000 ti mi ng 62 3e h ori zo ntal s y n c . o ffs e t = 4 8 p i xel s 3 0 0011 0000 d escri ptor 63 3f h ori zo ntal s y n c p u l se w i dth = 32 pi xel s 2 0 0010 0000 #1 64 40 verti cal s y n c o ffs e t = 3 l i nes : sync w i dth = 5 l i nes 3 5 0011 0101 65 41 h ori zo ntal v e rti cal s y n c o ffs e t/w i dth upper 2bi ts = 0 0 0 0000 0000 66 42 h ori zo ntal i mage si ze = 344.232m m (344) 5 8 0101 1000 67 43 verti cal i mage si ze = 193.536m m (194) c 2 1100 0010 68 44 h ori zo ntal & v e rti cal i mage si ze 1 0 0001 0000 69 45 h ori zo ntal border = 0 0 0 0000 0000 70 46 verti cal border = 0 0 0 0000 0000 71 47 non-i nterl aced,norm al d i spl a y,n o s te re o ,d i gi ta l separate sync,h /v pol negati ves 1 9 0001 1001 72 48 1366x768 @ 60? m ode pi xel c l ock (lsb) => 72.3m h z 3 e 0011 1110 73 49 (stored lsb fi rst) 1 c 0001 1100 74 4a h ori zo ntal a c ti ve = 1366 pi xel s (l ow er 8bi ts) 5 6 0101 0110 75 4b h ori zo ntal b l anki n g = 1 6 0 p i xel s (l ow er 8bi ts) a 0 1010 0000 76 4c h ori zo ntal a c ti ve : h o ri zo ntal b l anki ng (upper 4:4bi ts) 5 0 0101 0000 77 4d verti cal a v ti v e = 7 6 8 l i n e s (l ow er 8bi ts) 0 0 0000 0000 78 4e verti cal b l anki n g = 2 2 l i n e s (l ow er 8bi ts) 1 6 0001 0110 79 4f verti cal a c ti v e : v e rti cal b l anki n g (u p p e r 4 :4 b i ts) 3 0 0011 0000 ti mi ng 80 50 h ori zo ntal s y n c . o ffs e t = 4 8 p i xel s 3 0 0011 0000 d escri pti on 81 51 h ori zo ntal s y n c p u l se w i dth = 32 pi xel s 2 0 0010 0000 #2 82 52 verti cal s y n c o ffs e t = 3 l i nes : sync w i dth = 5 l i nes 3 5 0011 0101 83 53 h ori zo ntal v e rti cal s y n c o ffs e t/w i dth upper 2bi ts = 0 0 0 0000 0000 84 54 h ori zo ntal i mage si ze = 344.232m m (344) 5 8 0101 1000 85 55 verti cal i mage si ze = 193.536m m (194) c 2 1100 0010 86 56 h ori zo ntal & v e rti cal i mage si ze 1 0 0001 0000 87 57 h ori zo ntal border = 0 0 0 0000 0000 88 58 verti cal border = 0 0 0 0000 0000 89 59 non-i nterl aced,norm al d i spl a y,n o s te re o ,d i gi ta l separate sync,h /v pol negati ves 1 9 0001 1001 90 5a d etai l ed ti mi ng d escri ptor #3 0 0 0000 0000 91 5b 0 0 0000 0000 92 5c 0 0 0000 0000 9 3 5 d d a ta t y p e t a g : a l phanum eri c d a ta s tri ng (asc i i s tri ng) f e 1111 1110 94 5e 0 0 0000 0000 95 5f d el l p /n 1 s t c h a ra c te r = p 5 0 0 1 0 1 0 0 0 0 96 60 d el l p /n 2 n d c h a ra c te r = 1 3 1 0 0 1 1 0 0 0 1 97 61 d el l p/n 3rd c haracter = 2 3 2 0011 0010 ti mi ng 98 62 d el l p /n 4 th c h a ra c te r = 1 3 1 0 0 1 1 0 0 0 1 d e s c ri pti on 99 63 d el l p /n 5 th c h a ra c te r = h 4 8 0 1 0 0 1 0 0 0 # 3 100 64 ed i d revi si o n b u i l d n a m e = x b , r e v i si on # = a00 8 0 1000 0000 101 65 m anufacturer p/n = 1 3 1 0011 0001 102 66 m anufacturer p/n = 5 3 5 0011 0101 103 67 m anufacturer p/n = 6 3 6 0011 0110 104 68 m anufacturer p/n = w 5 7 0101 0111 105 69 m anufacturer p/n = h 4 8 0100 1000 106 6a m anufacturer p/n = 1 3 1 0011 0001 107 6b m anufacturer p/n (i f<13 char--> 0ah, then term i nate w i th a s c c o d e 0 a h ,s e t re m a i ni ng 0 a 0000 1010 fi el d name and comments val ue (h e x ) val ue (b i nary) www.datasheet.net/ datasheet pdf - http://www..co.kr/
product specification 31 / 31 lp156wh1 liquid crystal display ver. 0.3 aug. 08, 2008 appendix a. enhanced extended di splay identification data (eedid tm ) 3/3 byte# byte# (d e c i mal ) (h e x ) 108 6c d etai l ed ti mi ng d escri ptor #4 0 0 0000 0000 109 6d 0 0 0000 0000 110 6e 0 0 0000 0000 111 6f d ata type tag : d escri ptor d efi ned by m anufacturer 0 0 0000 0000 112 70 0 0 0000 0000 113 71 sm bu s val ue(step #1) = 10 ni ts f f 1111 1111 114 72 sm bu s val ue(step #2) = 17 ni ts f f 1111 1111 115 73 sm bu s val ue(step #3) = 24 ni ts f f 1111 1111 ti mi ng 116 74 sm bu s val ue(step #4) = 30 ni ts f f 1111 1111 d escri pti on 117 75 sm bu s val ue(step #5) = 60 ni ts f f 1111 1111 #4 118 76 sm bu s val ue(step #6) = 100 ni ts f f 1111 1111 119 77 sm bu s val ue(step #7) = 160 ni ts f f 1111 1111 120 78 sm bu s val ue(step #8) = 220 ni ts (t y p i cal l y = f f h, m a x ni ts) f f 1111 1111 121 79 si ngl e channel lvd s, no rtc support 1 port 0 1 0000 0001 122 7a bist support 0 1 0000 0001 123 7b (if<13 char--> 0ah, then term i nate w i th a s c c o d e 0 a h ,s e t re m a i ni ng char = 20h) 0 a 0000 1010 124 7c (if<13 char--> 0ah, then term i nate w i th a s c c o d e 0 a h ,s e t re m a i ni ng char = 20h) 2 0 0010 0000 125 7d (if<13 char--> 0ah, then term i nate w i th a s c c o d e 0 a h ,s e t re m a i ni ng char = 20h) 2 0 0010 0000 126 7e extensi o n fl a g = 0 0 0 0 0000 0000 extensi on fl ag 127 7f c hecksum 1 a 0001 1010 c hecksum fi el d name and comments val ue (h e x ) val ue (b i nary) www.datasheet.net/ datasheet pdf - http://www..co.kr/

▲Up To Search▲

Price & Availability of LP156WH1-TLB1

	To Download LP156WH1-TLB1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .