View D4C-1624_6620091.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

csm_d4c_ds_e_2_1 1 enclosed switch d4c compact limit switch that's also thin and highly sealed ? approved by en, ul, csa, and ccc (chinese standard). (ask your omron representative for information on approved models.) ? sealing characteristics that meet iec ip67 degree of protection. ? triple-sealed construction: plunger section sealed via nitrile rubber packing seal and diaphragm; switch section sealed via nitrile rubber cap; cable entrance sealed via encapsulating material. ? cable lengths of 3 and 5 m available on standard models. models also available with ul and csa-certified cables. ? multiple mounting possible wit h switches with plungers. ? models with red led indicators added to series for easy confirmation of operation. (set by default to light for non-operation.) ? vctf cables with ce marking. (applicable only to standard models.) be sure to read safety precautions on page 13 to 14 and safety precautions for all limit switches . model number structure model number legend (not all combinations are possible. ask your omron representative for details.) standard models d4c- @@@ (1) (2)(3) (1) rated current 1: 5 a at 250 vac, 4 a at 30 vdc 2: 5 a at 125 vac (with led indicator) 3: 4 a 30 vdc (with led indicator) 4: 0.1 a at 125 vac, 0.1 a at 30 vdc 5: 0.1 a at 125 vac (with led indicator) 6: 0.1 a at 30 vdc (with led indicator) (2) cable specifications 2: vctf oil-resistant cable (3 m) 3: vctf oil-resistant cable (5 m) 4: vctf (3 m) 5: vctf (5 m) 6: sjt(o) (3 m) 7: sjt(o) (5 m) (3) actuator 01: pin plunger 02: roller plunger 03: crossroller plunger 20: roller lever 24: roller lever (high-sensitivity model) 31: sealed pin plunger 32: sealed roller plunger 33: sealed crossroller 50: plastic rod 60: center roller lever pre-wired models d4c- @ 0 @@ - @@@@@@ (1) (2) (3) (4) (1) rated current 1: 1 a at 125 vac, 1 a at 30 vdc (without operation indicator) 2: 1 a at 125 vac (with operation indicator) 3: 1 a at 30 vdc (with operation indicator) (2) actuator 01: pin plunger 02: roller plunger 31: sealed plunger 32: sealed roller plunger 24: roller lever (high-sensitivity model) (3) wiring sp ecifications dk1ej: pre-wired models (3 conductors: dc specification) ak1ej: pre-wired models (3 conductors: ac specification) m1j: connector models for asi devices (2 conductors: no wiring) (4) cable length 03: 0.3 m wiring specifications internal switch connector com 3 nc 2 no 4 weather-resistant models d4c- @@@ -p (1)(2)(3) (4) (1) rated current 1: 5 a at 250 vac, 4 a at 30 vdc 2: 5 a at 125 vac (with led indicator) 3: 4 a at 30 vdc (with led indicator) 4: 0.1 a at 125 vac, 0.1 a at 30 vdc (2) cable sp ecifications 2: vctf oil-resistant cable (3 m) 3: vctf oil-resistant cable (5 m) (3) actuator 20: roller lever 24: roller lever (high-sensitivity model) 27: adjustable roller lever 29: adjustable rod lever (4) structure p: weather-resistant
2 d4c ordering information switches switches with no op eration indicator note: 1. models are available separately with resistance to viscous oils (oil drain holes are also available), but only with plun ger models. add ?-m? to the model number (example: d4c-1202 would be d4c-1202-m). 2. switches with variable roller levers are also availa ble. ask your nearest omron representative for details. *1. oil-resistant vinyl cabtire ca bles; approved by en and iec. *2. ordinary vinyl cabtire cabl es; approved by en and iec. *3. switches with sjt(o) cables (cables approv ed by ul and csa) are approved by ul and csa. actuator ratings cable cable length (m) standard microload 5 a at 250 vac, 4 a at 30 vdc 0.1 a at 125 vac, 0.1 a at 30 vdc vctf oil-resistant cable * 1 vctf cable * 2 sjt(o) cable * 3 vctf oil-resistant cable * 1 vctf cable * 2 model pin plunger 3 d4c-1201 d4c-1401 d4c-1601 d4c-4201 d4c-4401 5 d4c-1301 d4c-1501 d4c-1701 d4c-4301 d4c-4501 roller plunger 3 d4c-1202 d4c-1402 d4c-1602 d4c-4202 d4c-4402 5 d4c-1302 d4c-1502 d4c-1702 d4c-4302 d4c-4502 crossroller plunger 3 d4c-1203 d4c-1403 d4c-1603 d4c-4203 d4c-4403 5 d4c-1303 d4c-1503 d4c-1703 d4c-4303 d4c-4503 roller lever 3 d4c-1220 d4c-1420 d4c-1620 d4c-4220 d4c-4420 5 d4c-1320 d4c-1520 d4c-1720 d4c-4320 d4c-4520 roller lever, high- sensitivity 3 d4c-1224 d4c-1424 D4C-1624 d4c-4224 d4c-4424 5 d4c-1324 d4c-1524 d4c-1724 d4c-4324 d4c-4524 sealed pin plunger 3 d4c-1231 d4c-1431 d4c-1631 d4c-4231 d4c-4431 5 d4c-1331 d4c-1531 d4c-1731 d4c-4331 d4c-4531 sealed roller plunger 3 d4c-1232 d4c-1432 d4c-1632 d4c-4232 d4c-4432 5 d4c-1332 d4c-1532 d4c-1732 d4c-4332 d4c-4532 sealed crossroller plunger 3 d4c-1233 d4c-1433 d4c-1633 d4c-4233 d4c-4433 5 d4c-1333 d4c-1533 d4c-1733 d4c-4333 d4c-4533 plastic rod 3 d4c-1250 d4c-1450 d4c-1650 d4c-4250 d4c-4450 5 d4c-1350 d4c-1550 d4c-1750 d4c-4350 d4c-4550 center roller lever 3 d4c-1260 d4c-1460 d4c-1660 d4c-4260 d4c-4460 5 d4c-1360 d4c-1560 --- d4c-4360 d4c-4560
3 d4c standard switches with op eration indicator (red) note: ask your nearest omron representative for information on switching with approved international standards. *1. oil-resistant vinyl cabtire ca bles; approved by en and iec. *2. ordinary vinyl cabtire cables.; approved by en and iec. actuator ratings cable cable length (m) 0.1 a at 125 vac 0.1 a at 30 vdc vctf oil-resistant cable * 1 vctf cable * 2 vctf oil-resistant cable * 1 vctf cable * 2 model pin plunger 3 d4c-2201 d4c-2401 d4c-3201 d4c-3401 5 d4c-2301 d4c-2501 d4c-3301 d4c-3501 roller plunger 3 d4c-2202 d4c-2402 d4c-3202 d4c-3402 5 d4c-2302 d4c-2502 d4c-3302 d4c-3502 crossroller plunger 3 d4c-2203 d4c-2403 d4c-3203 d4c-3403 5 d4c-2303 d4c-2503 d4c-3303 d4c-3503 roller lever 3 d4c-2220 d4c-2420 d4c-3220 d4c-3420 5 d4c-2320 d4c-2520 d4c-3320 d4c-3520 roller lever, high- sensitivity 3 d4c-2224 d4c-2424 d4c-3224 d4c-3424 5 d4c-2324 d4c-2524 d4c-3324 d4c-3524 sealed pin plunger 3 d4c-2231 d4c-2431 d4c-3231 d4c-3431 5 d4c-2331 d4c-2531 d4c-3331 d4c-3531 sealed roller plunger 3 d4c-2232 d4c-2432 d4c-3232 d4c-3432 5 d4c-2332 d4c-2532 d4c-3332 d4c-3532 sealed crossroller plunger 3 d4c-2233 d4c-2433 d4c-3233 d4c-3433 5 d4c-2333 d4c-2533 d4c-3333 d4c-3533 plastic rod 3 d4c-2250 d4c-2450 d4c-3250 d4c-3450 5 d4c-2350 d4c-2550 d4c-3350 d4c-3550 center roller lever 3 d4c-2260 d4c-2460 d4c-3260 d4c-3460 5 d4c-2360 d4c-2560 d4c-3360 d4c-3560
4 d4c microload switches with operation indicator note: ask your nearest omron representative for information on switching with approved international standards. * oil-resistant vinyl cabtire cables; approved by en and iec. pre-wired models (use vc tf oil-resistant cable) note: 1. the @ contains the length of the cable. for example: 30 cm 4c-1001-ak1ej03 2. m1j models are also available. contact your omron sales representative for further information. 3. of the above model numbers, some with s pecial specifications are not registered. actuator ratings cable cable length (m) 0.1 a at 125 vac 0.1 a at 30 vdc vctf oil-resistant cable * vctf oil-resistant cable * model pin plunger 3 d4c-5201 d4c-6201 5 --- d4c-6301 roller plunger 3 d4c-5202 d4c-6202 5 d4c-5302 d4c-6302 crossroller plunger 3 d4c-5203 d4c-6203 5 d4c-5303 d4c-6303 roller lever 3 d4c-5220 d4c-6220 5 d4c-5320 d4c-6320 roller lever, high- sensitivity 3 d4c-5224 d4c-6224 5 d4c-5324 d4c-6324 sealed pin plunger 3--- d4c-6231 5--- d4c-6331 sealed roller plunger 3 d4c-5232 d4c-6232 5 d4c-5332 d4c-6332 sealed crossroller plunger 3--- d4c-6233 5--- d4c-6333 plastic rod 3 d4c-5250 d4c-6250 5 d4c-5350 d4c-6350 actuator ratings 1 a at 125 vac 1 a at 30 vdc operation indicator without operation indicator with operation indicator without operation indicator with operation indicator pin plunger d4c-1001-ak1ej @ d4c-2001-ak1ej @ d4c-1001-dk1ej @ d4c-3001-dk1ej @ roller plunger d4c-1002-ak1ej @ d4c-2002-ak1ej @ d4c-1002-dk1ej @ d4c-3002-dk1ej @ sealed plunger d4c-1031-ak1ej @ d4c-2031-ak1ej @ d4c-1031-dk1ej @ d4c-3031-dk1ej @ sealed roller plunger d4c-1032-ak1ej @ d4c-2032-ak1ej @ d4c-1032-dk1ej @ d4c-3032-dk1ej @ roller lever (high- sensitivity model) d4c-1024-ak1ej @ d4c-2024-ak1ej @ d4c-1024-dk1ej @ d4c-3024-dk1ej @
5 d4c weather-resistant models note: silicon rubber is used to increase resistance to the envir onment. silicon rubber, however, can generate silicon gas. (this can occur at room temperature, but the amount of silicon gas generated increases at higher temperatures.) silicon gas will react as a result of arc energy and form si licon oxide (sio 2 ). if silicon oxide accumulates on the contacts, contact interference can occur and ca n interfere with the device. before using a switch, test it u nder actual application conditions (including the environment and operating frequency) to confirm that no problems will occur in actual. mounting plates (order separately) the wl model incorporated by equipment can be replaced with the d4c together with the mounting plate without changing the posit ion of the dog or cam. list of replaceable models note: the wl01 @ is for micro loads. example of replacement note: the position of the dog remains unchanged. individual parts head/actuator note: 1. the model numbers for heads are of the form d4c-00 @@ , with the numbers in the squares indicating the type of actuator. 2. actuators for plunger models, plastic rod models, and center ro ller lever models cannot be ordered individually. they must be ordered together with the head. actuator operation indicator without operating indication with operating indication standard microload standard ratings cable length (m) 5 a at 250 vac 4 a at 30 vdc 0.1 a at 125 vac 0.1 a at 30 vdc 5 a at 125 vac 4 a at 30 vdc model roller lever 3 d4c-1220-p d4c-4220-p d4c-2220-p d4c-3220-p 5 d4c-1320-p --- --- --- roller lever (high- sensitivity model) 3 d4c-1224-p d4c-4224-p d4c-2224-p d4c-3224-p 5 d4c-1324-p d4c-4324-p d4c-2324-p d4c-3324-p adjustable roller lever 3 d4c-1227-p d4c-4227-p d4c-2227-p d4c-3227-p 5 d4c-1327-p d4c-4327-p d4c-2327-p d4c-3327-p adjustable rod lever 3 d4c-1229-p d4c-4229-p --- d4c-3229-p 5 d4c-1329-p --- d4c-2329-p d4c-3329-p wl model (actuator) d4c model (actuator) plate wld/wl01d (top plunger) d4c- @@ 01 (plunger) d4c-p001 wld2/wl01d2 (top roller plunger) d4c- @@ 02 (roller plunger) d4c-p002 wlca2/wl01ca2 (roller lever) d4c- @@ 20 (roller lever) d4c-p020 dog dog mounting plate actuator head (with actuator) actuator pin plunger d4c-0001 --- roller plunger d4c-0002 --- crossroller plunger d4c-0003 --- roller lever d4c-0020 wl-1a100 environment-resistant roller lever d4c-0020-p wl-1a100p1 roller lever d4c-0024 wl-1a100 variable roller lever d4c-0027 hl-1hpa320 variable rod lever d4c-0029 hl-1hpa500 sealed pin plunger d4c-0031 --- sealed roller plunger d4c-0032 --- sealed crossroller plunger d4c-0033 --- plastic rod d4c-0050 --- center roller lever d4c-0060 ---
6 d4c specifications approved standards ratings standard model pre-wired model approved standard ratings tv (en60947-5-1), ccc (gb14048.5) ul/csa b300 (d4c-16 @@ , -17 @@ ) b150 (d4c-26 @@ , -27 @@ ) b300 b150 characteristics note: the above figures are initial values. *1. the values are calculated at an operating temperature of +5 c to +35 c, and an operating humidity of 40% to 70%rh. contact your omron sales representative for more detailed information on other operating environments. *2. pre-wired models: 1,000,000 operations min. (dc specifications, switching current: 0.1 a) *3. outdoor specifications: 500,000 operations min. *4. excluding plastic rods. *5. pre-wired models: 250 v *6. pre-wired models: class iii agency standard file no. tv product service en60947-5-1 * 1, 3 ul ul508 e76675 * 2 csa csa c22.2 no.14 lr45746 * 2 ccc(cqc) gb14048.5 2003010305077626 * 3 *1. models with vctf oil-resistant cables and pre-wired models only. (applicable only to standard models listed on pages 2 to 4.) *2. sjt(o)-cable models only. (applicable only to standard models listed on pages 2 to 3.) *3. ask your omron representative for information on approved models. rated voltage non-inductive load (a) inductive load (a) resistive load lamp load inductive load motor load nc no nc no nc no nc no 125 vac 250 vac 5 (0.1) 5 1.5 1 0.7 0.5 3 2 2.5 1.5 1.3 0.8 8 vdc 5 (0.1) 2 5 4 3 14 vdc 5 (0.1) 2 4 4 3 30 vdc 4 (0.1) 2 3 3 3 125 vdc 0.4 0.05 0.4 0.05 250 vdc 0.2 0.03 0.2 0.03 inrush current nc 20 a max. no 10 a max. note: 1. the values given on the left are steady-state currents. 2. inductive loads have a power factor of 0.4 min. (ac) and a time constant of 7 ms max. (dc). 3. lamp loads have an inrush current of 10 times the steady-state current. 4. motor loads have an inrush current of 6 times the steady-state current. 5. the values "0.1" given in parentheses are for micro load models. rated voltage non-inductive load (a) inductive load (a) resistive load lamp load inductive load motor load nc no nc no nc no nc no 125 vac1110.71111 30 vdc 11111111 model applicable category and ratings i the d4c-1 @@@ ac-15 2 a/250 v dc-12 2 a/30 v 5 a 4 a d4c-2 @@@ ac-15 2 a/125 v 5 a d4c-3 @@@ dc-12 2 a/30 v 4 a d4c-4 @@@ ac-14 0.1 a/125 v dc-12 0.1 a/30 v 0.5 a 0.5 a d4c-5 @@@ ac-14 0.1 a/125 v 0.5 a d4c-6 @@@ dc-12 0.1 a/30 v 0.5 a rated voltage carry current current (a) volt-amperes (va) make break make break 120 vac 240 vac 5 a 30 15 3 1.5 3,600 3,600 360 360 rated voltage carry current current (a) volt-amperes (va) make break make break 120 vac 5 a 30 3 3,600 360 degree of protection ip67 durability * 1 mechanical * 3 10,000,000 operations min. electrical * 2 200,000 operations min. (5 a at 125 vac, resistive load) operating speed 0.1 mm/s to 0.5 m/s (in case of plunger) 1 mm/s to 1 m/s (in case of roller lever) operating frequency mechanical 120 operations/min electrical 30 operations/min rated frequency 50/60 hz insulation resistance 100 m ? min. (at 500 vdc) contact resistance (initial) 250 m ? max. (initial value with 2-m vctf cable) 300 m ? max. (initial value with 3-m vctf cable) 400 m ? max. (initial value with 5-m vctf cable) dielectric strength between terminals of the same polarity 1,000 vac, 50/60 hz for 1 min between current- carrying metal part and ground 1,500 vac, 50/60 hz for 1 min uimp: 2.5 kv (en60947-5-1) between each terminal and non-current-carry- ing metal part, 1,500 vac, 50/60 hz for 1 min uimp: 2.5 kv(en60947-5-1) rated insulation voltage (ui) 300 v (en60947-5-1) * 5 pollution degree (operating environment) 3 (en60947-5-1) short-circuit protective device (scpd) 10 a fuse type gi or gg (iec60269) conditional short-circuit current 100 a (en60947-5-1) conventional enclosed thermal current (i the) 5 a, 4 a, 0.5 a (en60947-5-1) protection against electric shock class i (with grounding wire) * 6 vibration re- sistance malfunction 10 to 55 hz, 1.5-mm double amplitude * 4 shock re- sistance destruction 1,000 m/s 2 min. malfunction 500 m/s 2 min. * 4 ambient operating temperature ? 10 c to +70 c (with no icing) ambient operating humidity 35% to 95%rh weight (d4c-1202) with 3-m vctf cable: 360 g with 5-m vctf cable: 540 g
7 d4c engineering data leakage current for led-indicator models the leakage currents and resistances of led-indicator models are given in the following table. structure and nomenclature structure standard models weather-resistant models model voltage leakage current resistance d4c-2 @@@ 125 vac 1.7 ma 68 k ? d4c-3 @@@ 30 vdc 1.7 ma 15 k ? d4c-5 @@@ 125 vac 1.7 ma 68 k ? d4c-6 @@@ 30 vdc 1.7 ma 15 k ? 500 300 100 30 10 1 1 0234567 125 vac 250 vac 3 5 50 durability (x 10 4 operations) switching current (ma) operating temperature: 20 2 c operating humidity: 65 5 c operating frequency: 30 operations/min (cos = 1, l/r = 0) operating temperature: 5 c to 35 c operating humidity: 40% to 70% operating frequency: 30 operations/min (cos =1, l/r = 0) 1,000 300 500 700 100 30 10 20 0 40 60 80 100 120 125 vac 30 vdc 3 5 50 durability (x 10 4 operations) switching current (ma) electrical durability d4c-1 @@@ , -2 @@@ , -3 @@@ d4c-4 @@@ , -5 @@@ , -6 @@@ o-ring (nbr) built-in switch roller lever diaphragm (nbr) o-ring (nbr) protective cap (nbr) ground terminal molded resin cable roller lever models without indicator shaft section sea l by fitting an o-ring to the rotary shaft and with an appropriate interference of the screws, high-sealing properties are maintained. the o-ring is made of silicone rubber and is resistant to temperature changes and adverse weather conditions. roller the roller is made of self-lubricating sintered stainless steel and boasts high resistance to wear. head-mounting screw diaphragm the diaphragm is made of silicone rubber and is resistant to temperature changes and adverse weather conditions. cable vinyl cabtire cable and is resistant to adverse weather conditions. lever the lever forged of anti-corrosive aluminium alloy features high corrosion resistances and outstanding ruggedness. built-in switch both standard load and microload models available. rotary shaft the shaft is made of stainless steel decreasing the likelihood of rusting. roller lever setscrew this screw is made of stainless steel and has high corrosion resistance. roller lever models without indicator
8 d4c contact form standard models/weather-resistant models without operat ion indicator with operation indicator (lit when not actuated) <24 vdc led> <100 vac led> connector models fo r asi devices (-m1j) without operat ion indicator with operation indicator (lit when not actuated) pre-wired models (-ak1ej @ , -dk1ej @ ) without operation indicator with operation indicator (lit when not actuated) <24 vdc led> <100 vac led> *1. yellow/green: vctf oil-resistant cable green: vctf cable *2. sjt(o) cable approved by ul and csa. *3. e (ground) is not grounded. *4. the position of the positioning pi ece is not fixed. using an l-shaped connector may result in failure. use only a straight connector. note: ?lit when not actuated? means that when the actuator is in the free position, the indicator is lit, and when the actuator is turned or pushed and the contact comes into contact with the no side, the indicator turns off. e nc (red) no (white) (yellow/green stripes) *1 (black)com (blue) *2 (green) *2 e nc (red) (black) com no (white) (blue) *2 (yellow/green) *1 (green) *2 15 k ? e nc (red) (black) com no (white) (blue) *2 (yellow/green) *1 (green) *2 68 k ? pin no.3 com no pin no.4 pin no.3 com no pin no.4 no com positioning piece*4 for dc e *3 no pin no.4 nc pin no.2 pin no.3 com e *3 no pin no.4 nc pin no.2 pin no.3 com 15 k ? e *3 no pin no.4 nc pin no.2 pin no.3 com 68 k ? nc no com positioning piece*4 nc no com positioning piece* 4 for ac for dc
9 d4c dimensions and operating characteristics switches standard models note: unless otherwise specified, a tolerance of 0.4 mm applies to all dimensions. model operating characteristics d4c- @@ 01 d4c- @@ 02 d4c- @@ 03 d4c- @@ 20 d4c- @@ 20-p d4c- @@ 24 d4c- @@ 24-p operating force of max. release force rf min. pretravel pt max. overtravel ot min. movement differential md max. 11.77 n 4.41 n 1.8 mm 3 mm 0.2 mm 11.77 n 4.41 n 1.8 mm 3 mm 0.2 mm 11.77 n 4.41 n 1.8 mm 3 mm 0.2 mm 5.69 n 1.47 n 25 40 3 5.69 n 1.47 n 10 3 50 3 operating position op 15.7 1 mm 28.5 1 mm 28.5 1 mm --- --- models without led indicators are shown in the illust rations and dimensions diagrams. refer to page 11 for models with led indicators . the boxes in the model numbers are replaced with the rating and cable type. refer to page 1 for the model number structure . op pt 16 2.8 2 1.4 1.5 7.5 4.5 8 23 2 34 10 dia. stainless steel plunger 40 max. 54.2 max. 49 max. vctf cable, 0.75 mm 2 , 4 conductor finishing o.d.: 7.6 correct setting position two, 5.1 +0.2 dia. holes spot facing 10.2 dia. depth: 6 0 25 0.1 pin plunger d4c- @@ 01 65 max. * s-flex vctf cables are used for weather-resistant models. 16 38r 7 2 11.4 1.4 1.5 7.5 8 23 2 34 vctf cable, 0.75 mm 2 , 4 conductor finishing o.d.: 7.6 two, 5.1 +0.2 dia. holes spot facing 10.2 dia. depth: 6 0 * 17.5 dia. x 7 stainless sintered roller 102.7 max. 40 max. 50 max. 25 0.1 44 0.8 30.2 0.8 31.5 0.8 m5 (length: 12) allen-head bolt roller lever d4c- @@ 20 d4c- @@ 20-p op pt 16 2.8 2 1.4 1.5 7.5 7 8 23 2 34 12 dia. x 4.4 stainless steel roller 40 max. vctf cable, 0.75 mm 2 , 4 conductor finishing o.d.: 7.6 correct setting position two, 5.1 +0.2 dia. holes spot facing 10.2 dia. depth: 6 0 25 0.1 67 max. 51.5 max. roller plunger d4c- @@ 02 op pt 16 2.8 2 1.4 1.5 7.5 7 8 23 2 34 12 dia. x 4.4 stainless steel roller 40 max. vctf cable, 0.75 mm 2 , 4 conductor finishing o.d.: 7.6 correct setting position tw o, 5 . 1 +0.2 dia. holes spot facing 10.2 dia. depth: 6 0 25 0.1 67 max. 51.5 max. crossroller plunger d4c- @@ 03 16 38r 7 2 11.4 1.4 1.5 7.5 8 23 2 34 65 max. * s-flex vctf cables are used for weather-resistant models. vctf cable, 0.75 mm 2 , 4 conductor finishing o.d.: 7.6 two, 5.1 +0.2 dia. holes spot facing 10.2 dia. depth: 6 0 * 17.5 dia. x 7 stainless sintered roller 102.7 max. 40 max. 50 max. 25 0.1 44 0.8 30.2 0.8 31.5 0.8 m5 (length: 12) allen-head bolt roller lever (high-sensitivity model) d4c- @@ 24 d4c- @@ 24-p
10 d4c note: unless otherwise specified, a tolerance of 0.4 mm applies to all dimensions. * the tt is a reference value. operating characteristics model d4c- @@ 31 d4c- @@ 32 d4c- @@ 33 operating force of max. release force rf min. pretravel pt max. overtravel ot min. movement differential md max. 17.65 n 4.41 n 1.8 mm 3 mm 0.2 mm 17.65 n 4.41 n 1.8 mm 3 mm 0.2 mm 17.65 n 4.41 n 1.8 mm 3 mm 0.2 mm operating position op total travel tt * 24.9 1 mm (5) mm 34.3 1 mm (5) mm 34.3 1 mm (5) mm op pt 16 2 1.4 1.5 7.5 4.0 8 23 2 34 two, 5.1 +0.2 dia. holes spot facing 10.2 dia. depth: 6 vctf cable, 0.75 mm 2 , 4 conductor finishing o.d.: 7.6 40 max. 49 max. 10 dia. stainless steel plunger 25 0.1 rubber cap 0 s ealed plunger d4c- @@ 31 op pt 16 2 1.4 1.5 7.5 4.0 8 23 2 34 two, 5.1 +0.2 dia. holes spot facing 10.2 dia. depth: 6 0 rubber cap 12 dia. x 4.4 stainless steel roller 40 max. 25 0.1 49 max. vctf cable, 0.75 mm 2 , 4 conductor finishing o.d.: 7.6 s ealed roller plunger d4c- @@ 32 op pt 16 2 1.4 1.5 7.5 4.0 8 23 2 34 two, 5.1 +0.2 dia. holes spot facing 10.2 dia. depth: 6 0 rubber cap 12 dia. x 4.4 stainless steel roller 40 max. 25 0.1 49 max. vctf cable, 0.75 mm 2 , 4 conductor finishing o.d.: 7.6 sealed crossroller plunger d4c- @@ 33
11 d4c note: unless otherwise specified, a tolerance of 0.4 mm applies to all dimensions. models with led indicator the dimensions of the led indicator for models equipped with one are shown below. pre-wired models note: unless otherwise specified, a tolerance of 0.4 mm applies to all dimensions. note: specifications are th e same for -m1j switches. 104 2.5 38 3.2 dia. 6.6 dia. *2 42 16 2 1.4 1.5 7.5 4.5 8 23 2 34 *1 vctf cable, 0.75 mm 2 , 4 conductor finishing o.d.: 7.6 two, 5.1 +0.2 dia. holes spot facing 10.2 dia. depth: 6 0 rubber cap nylon rod 40 max. 25 0.1 49 max. *1 operation is possible in any direction except in parallel to the axis. *2 the ideal range for operation is between the tip of the rod and 1/3 of the length of the actuator. plastic rod d4c- @@ 50 56.9 38r 18.9 16 2 1.5 7.5 11.4 7 8 23 2 34 1.4 vctf cable, 0.75 mm 2 , 4 conductor finishing o.d.: 7.6 two, 5.1 +0.2 dia. holes spot facing 10.2 dia. depth: 6 0 40 max. 25 0.1 102.7 max. 17.5 dia. x 7 stainless sintered roller center roller lever plunger d4c- @@ 60 operating characteristics model d4c- @@ 50 d4c- @@ 60 operating force of max. release force rf min. pretravel pt max. overtravel ot min. movement differential md max. 1.47 n --- 15 --- --- 6.67 n 1.47 n 10 3 50 3 operating position op total travel tt --- --- --- --- -&% op pt 16 2.8 2 1.4 1.5 7.5 4.5 8 23 xs2h-d421 2 34 two, 5.1 +0.2 dia. holes spot facing 10.2 dia. depth: 6 0 40 max. 54.2 max. 49 max. 25 0.1 10 dia. stainless steel plunger correct setting position 6 dia. pin plunger d4c- @ 001- @ k1ej @ d4c- @ 001-m1j @ op pt 16 2.8 2 7.5 7 8 23 2 34 1.4 1.5 xs2h-d421 two, 5.1 +0.2 dia. holes spot facing 10.2 dia. depth: 6 0 40 max. 25 0.1 12 dia. x 4.4 stainless steel roller 67 max. 51.5 max. correct setting position 6 dia. roller plunger d4c- @ 002- @ k1ej @ d4c- @ 002-m1j @ model operating characteristics d4c- @ 001 - @ k1ej @ d4c- @ 002 - @ k1ej @ operating force of max. release force rf min. pretravel pt max. overtravel ot min. movement differential md max. 11.77 n 4.41 n 1.8 mm 3 mm 0.2 mm 11.77 n 4.41 n 1.8 mm 3 mm 0.2 mm operating position op 15.7 1 mm 28.5 1 mm
12 d4c note: unless otherwise specified, a tolerance of 0.4 mm applies to all dimensions. note: specifications are th e same for -m1j switches note: unless otherwise specified, a tolerance of 0.4 mm applies to all dimensions. model operating characteristics d4c- @ 031 - @ k1ej @ d4c- @ 032 - @ k1ej @ operating force of max. release force rf min. pretravel pt max. overtravel ot min. movement differential md max. 17.65 n 4.41 n 1.8 mm 3 mm 0.2 mm 17.65 n 4.41 n 1.8 mm 3 mm 0.2 mm operating position op 24.9 1 mm 34.3 1 mm op pt 16 2 1.4 1.5 7.5 4.0 8 23 xs2h-d421 2 34 two, 5.1 +0.2 dia. holes spot facing 10.2 dia. depth: 6 0 10 dia. stainless steel plunger 40 max. 49 max. 25 0.1 6 dia. rubber cap s ealed pin plunger d4c- @ 031- @ k1ej @ d4c- @ 031-m1j @ op pt 16 2 7.5 4.0 8 23 2 34 1.4 1.5 xs2h-d421 two, 5.1 +0.2 dia. holes spot facing 10.2 dia. depth: 6 0 40 max. 25 0.1 12 dia. x 4.4 stainless steel roller 6 dia. 49 max. rubber cap s ealed roller plunger d4c- @ 032- @ k1ej @ d4c- @ 032-m1j @ 16 38r 7 2 11.4 7.5 8 23 1.4 1.5 xs2h-d421 2 34 two, 5.1 +0.2 dia. holes spot facing 10.2 dia. depth: 6 0 40 max. 25 0.1 102.7 max. 17.5 dia. x 7 stainless sintered roller 50 max. 44 0.8 30.2 0.8 31.5 0.8 65 max. 6 dia. m5 (length: 12) allen-head bolt roller lever (high- sensitivity model) d4c- @ 024- @ k1ej @ d4c- @ 024-m1j @ note: specifications are the same for -m1j switches operating characteristics model d4c- @ 024- @ k1ej @ operating force of max. release force rf min. pretravel pt max. overtravel ot min. movement differential md max. 5.69 n 1.47 n 10 3 50 3 operating position op ---
13 d4c weather-resistant models note: unless otherwise specified, a tolerance of 0.4 mm applies to all dimensions. * operation characteristics for the d4c- @@ 27-p and d4c- @@ 29-p are for a lever length of 38 mm. safety precautions refer to safety precautions for all limit switches . operating environment ? seal material may deteriorate if a switch is used outdoor or where subject to special cutting oils, so lvents, or chemicals. always appraise performance under act ual application conditions and set suitable maintenance and replacement periods. ? install switches where they will not be directly subject to cutting chips, dust, or dirt. the actuator and switch must also be protected from the accumulation of cutting chips or sludge. ? constantly subjecting a switch to vibration or shock can result in wear, which can lead to contact interference with contacts, operation failure, reduced dur ability, and other problems. excessive vibration or shock can l ead to false contact operation or damage. install switches in lo cations not subject to shock and vibration and in orientations that will not produce resonance. ? the switches have physical contac ts. using them in environments containing silicon gas wi ll result in the formation of silicon oxide (sio 2 ) due to arc energy. if silicon oxide accumulates on the contacts, contact interference can oc cur. if silicon oil, silicon filling agents, silicon cables, or other sili con products are present near the switch, suppress arcing with cont act protective circuits (surge killers) or remove the source of silicon gas. handling the bottom of the switch at the cable outlet is resin-molded. secure the cable at a point 5 cm from the switch bottom to prevent exertion of excess force on the cable. when bending the cable, provide a bending radius of 45 mm min. so as not to damage the cable insulation or sheath. excessive bending may cause fire or leakage current. connections ? be sure to connect a fuse with a breaking current 1.5 to 2 times larger than the rated current to the limit switch in series in order to protect the limit switch from damage due to short-circuiting. ? when using the limit switch for the en ratings, use the gi or gg 10- a fuse. operating characteristics model d4c- @@ 27-p d4c- @@ 29-p * operating force of max. release force rf min. pretravel pt max. overtravel ot min. movement differential md max. 5.69 n 1.47 n 25 40 3 5.69 n 1.47 n 25 40 3 precautions for correct use 16 7 2 11.4 1.4 2 1.5 7.5 8 23 2 34 vctf cable, 0.75 mm 2 , 4 conductor finishing o.d.: 7.6 two, 5.1 +0.2 dia. holes spot facing 10.2 dia. depth: 6 0 40 max. 25 0.1 52.3 0.8 31.5 0.8 17.5 dia. x 7 stainless steel roller 30r to 75r (variable) m5 (length: 16) allen-head bolt m5 (length: 12) allen-head bolt 57.7 max. 65 max. adjustable roller lever d4c- @@ 27-p 44 16 31.5 5.4 7 2 11.4 1.4 1.5 7.5 8 23 2 34 vctf cable, 0.75 mm 2 , 4 conductor finishing o.d.: 7.6 40 max. 25 0.1 3 dia. x 160 stainless steel lever m5 (length: 16) allen-head bolt m5 (length: 12) allen-head bolt 55 max. 65 max. two, 5.1 +0.2 dia. holes spot facing 10.2 dia. depth: 6 0 adjustable rod lever d4c- @@ 29-p not suitable suitable secure here 5 cm bending radius (r45 mm min.)
14 d4c operation ? operation method, shapes of ca m and dog, operating frequency, and overtravel have a si gnificant effect on the service life and precision of a limit switch. for this reason, the dog angle must be 30 max., the surface roughness of the dog must be 6.3 s min. and hardness must be hv 400 to 500. ? to allow the plunger-type actuator to travel properly, adjust the dog and cam to the proper setting positions. the pr oper position is where the plunger groove fits the bushing top. ? to allow the roller lever-type act uator to travel properly, adjust the dog and cam so that the arrow head is positioned between the two convex markers as shown below. mounting ? a maximum of 6 switches may be group-mounted. in this case, pay attention to the mounting direction so that the convex part of the group-mounting guide on one switch fits into the concave part of the guide on the other switch as shown in the figure below. for group mounting, the mounting panel must have a thickness (t) of 6 mm min. ? if the mounting panel is warped or has protruding parts, a malfunction may result. make sure that the mounting panel is not warped and has even surfaces. ? use a switch with a rubber cap w hen using the plunger type in an environment where malfunction is possible due to environmental conditions such as dust or cutt ing chips which may not allow resetting. ? do not expose the switch to water exceeding 70 c or use it in steam. ? when the d4c is used in a circuit of a device to be exported to europe, classified as overvoltage cl ass iii as specified in iec664, provide a contact protection circuit. ? tighten each screw to a torque ac cording to the following table. micro-load models (d4c-4, -5, -6) micro-load models can be used for switching in the range shown below. 2.8 mm dog bushing top groove 2.8 mm arrow head not correct correct convex markers not correc t correct no. type appropriate tightening torque * 1 m5 allen-head bolt 4.90 to 5.88 n m 2 m3.5 head mounting screw 0.78 to 0.88 n m 3 m5 allen-head bolt 4.90 to 5.88 n m group-mounting guide (front: convex rear: concave) mounting panel 16 mm group-mounting guide (front: convex rear: concave) t group mounting two, 5.2-dia. or m5 screw holes 25 0.1 mounting holes * by removing the two screws from the head, the head direction can be rotated 180 . after changing the head direction, re-tighten to the torque specified above. be careful not to allow any foreign substance to enter the switch. 30 24 12 5 0 1 10 100 1,000 0.1 1 ma 26 ma 0.16 ma 800 mw 5 mw 100 ma 160 ma switching range for micro-load models switching range for standard- load models switching not possible in this range current (ma) voltage (v)
r e a d a n d u n d e r s t a n d t h i s c a t a l o g p l e a s e r e a d a n d u n d e r s t a n d t h i s c a t a l o g b e f o r e p u r c h a s i n g t h e p r o d u c t s . p l e a s e c o n s u l t y o u r o m r o n r e p r e s e n t a t i v e i f y o u h a v e a n y q u e s t i o n s o r c o m m e n t s . w a r r a n t y a n d l i m i t a t i o n s o f l i a b i l i t y w a r r a n t y o m r o n ' s e x c l u s i v e w a r r a n t y i s t h a t t h e p r o d u c t s a r e f r e e f r o m d e f e c t s i n m a t e r i a l s a n d w o r k m a n s h i p f o r a p e r i o d o f o n e y e a r ( o r o t h e r p e r i o d i f s p e c i f i e d ) f r o m d a t e o f s a l e b y o m r o n . o m r o n m a k e s n o w a r r a n t y o r r e p r e s e n t a t i o n , e x p r e s s o r i m p l i e d , r e g a r d i n g n o n - i n f r i n g e m e n t , m e r c h a n t a b i l i t y , o r f i t n e s s f o r p a r t i c u l a r p u r p o s e o f t h e p r o d u c t s . a n y b u y e r o r u s e r a c k n o w l e d g e s t h a t t h e b u y e r o r u s e r a l o n e h a s d e t e r m i n e d t h a t t h e p r o d u c t s w i l l s u i t a b l y m e e t t h e r e q u i r e m e n t s o f t h e i r i n t e n d e d u s e . o m r o n d i s c l a i m s a l l o t h e r w a r r a n t i e s , e x p r e s s o r i m p l i e d . l i m i t a t i o n s o f l i a b i l i t y o m r o n s h a l l n o t b e r e s p o n s i b l e f o r s p e c i a l , i n d i r e c t , o r c o n s e q u e n t i a l d a m a g e s , l o s s o f p r o f i t s o r c o m m e r c i a l l o s s i n a n y w a y c o n n e c t e d w i t h t h e p r o d u c t s , w h e t h e r s u c h c l a i m i s b a s e d o n c o n t r a c t , w a r r a n t y , n e g l i g e n c e , o r s t r i c t l i a b i l i t y . i n n o e v e n t s h a l l t h e r e s p o n s i b i l i t y o f o m r o n f o r a n y a c t e x c e e d t h e i n d i v i d u a l p r i c e o f t h e p r o d u c t o n w h i c h l i a b i l i t y i s a s s e r t e d . i n n o e v e n t s h a l l o m r o n b e r e s p o n s i b l e f o r w a r r a n t y , r e p a i r , o r o t h e r c l a i m s r e g a r d i n g t h e p r o d u c t s u n l e s s o m r o n ' s a n a l y s i s c o n f i r m s t h a t t h e p r o d u c t s w e r e p r o p e r l y h a n d l e d , s t o r e d , i n s t a l l e d , a n d m a i n t a i n e d a n d n o t s u b j e c t t o c o n t a m i n a t i o n , a b u s e , m i s u s e , o r i n a p p r o p r i a t e m o d i f i c a t i o n o r r e p a i r . a p p l i c a t i o n c o n s i d e r a t i o n s s u i t a b i l i t y f o r u s e o m r o n s h a l l n o t b e r e s p o n s i b l e f o r c o n f o r m i t y w i t h a n y s t a n d a r d s , c o d e s , o r r e g u l a t i o n s t h a t a p p l y t o t h e c o m b i n a t i o n o f p r o d u c t s i n t h e c u s t o m e r ' s a p p l i c a t i o n o r u s e o f t h e p r o d u c t s . a t t h e c u s t o m e r ' s r e q u e s t , o m r o n w i l l p r o v i d e a p p l i c a b l e t h i r d p a r t y c e r t i f i c a t i o n d o c u m e n t s i d e n t i f y i n g r a t i n g s a n d l i m i t a t i o n s o f u s e t h a t a p p l y t o t h e p r o d u c t s . t h i s i n f o r m a t i o n b y i t s e l f i s n o t s u f f i c i e n t f o r a c o m p l e t e d e t e r m i n a t i o n o f t h e s u i t a b i l i t y o f t h e p r o d u c t s i n c o m b i n a t i o n w i t h t h e e n d p r o d u c t , machin e , s y s t e m , o r o t h e r a p p l i c a t i o n o r u s e . t h e f o l l o w i n g a r e s o m e e x a m p l e s o f a p p l i c a t i o n s f o r w h i c h p a r t i c u l a r a t t e n t i o n m u s t b e g i v e n . t h i s i s n o t i n t e n d e d t o b e a n e x h a u s t i v e l i s t o f a l l p o s s i b l e u s e s o f t h e p r o d u c t s , n o r i s i t i n t e n d e d t o i m p l y t h a t t h e u s e s l i s t e d m a y b e s u i t a b l e f o r t h e p r o d u c t s : o u t d o o r u s e , u s e s i n v o l v i n g p o t e n t i a l c h e m i c a l c o n t a m i n a t i o n o r e l e c t r i c a l i n t e r f e r e n c e , o r c o n d i t i o n s o r u s e s n o t d e s c r i b e d i n t h i s c a t a l o g . n u c l e a r e n e r g y c o n t r o l s y s t e m s , c o m b u s t i o n s y s t e m s , r a i l r o a d s y s t e m s , a v i a t i o n s y s t e m s , m e d i c a l e q u i p m e n t , a m u s e m e n t m a c h i n e s , v e h i c l e s , s a f e t y e q u i p m e n t , a n d i n s t a l l a t i o n s s u b j e c t t o s e p a r a t e i n d u s t r y o r g o v e r n m e n t r e g u l a t i o n s . s y s t e m s , m a c h i n e s , a n d e q u i p m e n t t h a t c o u l d p r e s e n t a r i s k t o l i f e o r p r o p e r t y . p l e a s e k n o w a n d o b s e r v e a l l p r o h i b i t i o n s o f u s e a p p l i c a b l e t o t h e p r o d u c t s . n e v e r u s e t h e p r o d u c t s f o r a n a p p l i c a t i o n i n v o l v i n g s e r i o u s r i s k t o l i f e o r p r o p e r t y w i t h o u t e n s u r i n g t h a t t h e s y s t e m a s a w h o l e h a s b e e n d e s i g n e d t o a d d r e s s t h e r i s k s , a n d t h a t t h e o m r o n p r o d u c t s a r e p r o p e r l y r a t e d a n d i n s t a l l e d f o r t h e i n t e n d e d u s e w i t h i n t h e o v e r a l l e q u i p m e n t o r s y s t e m . p r o g r a m m a b l e p r o d u c t s o m r o n s h a l l n o t b e r e s p o n s i b l e f o r t h e u s e r ' s p r o g r a m m i n g o f a p r o g r a m m a b l e p r o d u c t , o r a n y c o n s e q u e n c e t h e r e o f . d i s c l a i m e r s c h a n g e i n s p e c i f i c a t i o n s p r o d u c t s p e c i f i c a t i o n s a n d a c c e s s o r i e s m a y b e c h a n g e d a t a n y t i m e b a s e d o n i m p r o v e m e n t s a n d o t h e r r e a s o n s . i t i s o u r p r a c t i c e t o c h a n g e m o d e l n u m b e r s w h e n p u b l i s h e d r a t i n g s o r f e a t u r e s a r e c h a n g e d , o r w h e n s i g n i f i c a n t c o n s t r u c t i o n c h a n g e s a r e m a d e . h o w e v e r , s o m e s p e c i f i c a t i o n s o f t h e p r o d u c t s m a y b e c h a n g e d w i t h o u t a n y n o t i c e . w h e n i n d o u b t , s p e c i a l m o d e l n u m b e r s m a y b e a s s i g n e d t o f i x o r e s t a b l i s h k e y s p e c i f i c a t i o n s f o r y o u r a p p l i c a t i o n o n y o u r r e q u e s t . p l e a s e c o n s u l t w i t h y o u r o m r o n r e p r e s e n t a t i v e a t a n y t i m e t o c o n f i r m a c t u a l s p e c i f i c a t i o n s o f p u r c h a s e d p r o d u c t s . d i m e n s i o n s a n d w e i g h t s d i m e n s i o n s a n d w e i g h t s a r e n o m i n a l a n d a r e n o t t o b e u s e d f o r m a n u f a c t u r i n g p u r p o s e s , e v e n w h e n t o l e r a n c e s a r e s h o w n . p e r f o r m a n c e d a t a perfor m a n c e d a t a g i v e n i n t h i s c a t a l o g i s p r o v i d e d a s a g u i d e f o r t h e u s e r i n d e t e r m i n i n g s u i t a b i l i t y a n d d o e s n o t c o n s t i t u t e a w a r r a n t y . i t m a y r e p r e s e n t t h e r e s u l t o f o m r o n ? s t e s t c o n d i t i o n s , a n d t h e u s e r s m u s t c o r r e l a t e i t t o a c t u a l a p p l i c a t i o n r e q u i r e m e n t s . a c t u a l p e r f o r m a n c e i s s u b j e c t t o t h e o m r o n w a r r a n t y a n d l i m i t a t i o n s o f l i a b i l i t y . e r r o r s a n d o m i s s i o n s t h e i n f o r m a t i o n i n t h i s d o c u m e n t h a s b e e n c a r e f u l l y c h e c k e d a n d i s b e l i e v e d t o b e a c c u r a t e ; h o w e v e r , n o r e s p o n s i b i l i t y i s a s s u m e d f o r c l e r i c a l , t y p o g r a p h i c a l , o r p r o o f r e a d i n g e r r o r s , o r o m i s s i o n s . 2008 . 1 1 i n t h e i n t e r e s t o f p r o d u c t i m p r o v e m e n t , s p e c i f i c a t i o n s a r e s u b j e c t t o c h a n g e w i t h o u t n o t i c e . o m r o n c o r p o r a t i o n i n d u s t r i a l a u t o m a t i o n c o m p a n y h t t p : / / w w w . i a . o m r o n . c o m / ( c ) c o p y r i g h t o m r o n c o r p o r a t i o n 2 0 0 8 a l l r i g h t r e s e r v e d .

▲Up To Search▲

Price & Availability of D4C-1624

	To Download D4C-1624 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .