u f s 1 0 5 thru u fs 12 0 1 amp s u p er fast recovery rectifier 50 to 2 00 volts do-214aa features for surface mount applications extremely low thermal resistance easy pick and place high temp soldering: 250 c for 10 seconds at terminals s u p er fast recovery times for high efficiency dimensions inches mm dim min max min max note a .07 8 .11 6 1.9 8 2.9 5 1 b .0 75 .08 9 1. 90 2.2 5 c .00 2 .008 . 05 .20 d --- .02 --- .51 e .03 5 .0 55 . 90 1. 40 f .065 .0 91 1.65 2. 32 g .205 .22 4 5.21 5. 70 h .160 .180 4.06 4.57 j .130 .155 3.30 3.94 1) maximum jedec spec is .096? or 2.44 mm maximum ratings electrical characteristics @ 25 c unless otherwise specified average forward current i f(av) 1.0a t j = 1 00 c peak forward surge current i fsm 3 5 a 8.3ms, half sine maximum instantaneous forward voltage v f . 9 5 v i fm = 1 .0a; t j = 25 c* maximum dc reverse current at rated dc blocking voltage i r 5 m a 5 0 m a t j = 25 c t j = 125 c typical junction capacitance c j 1 5pf measured at 1.0mhz, v r =4.0v *pulse test: pulse width 200 m sec, duty cycle 2% h j e f g a b d c 0.070? 0.090 0.085? suggested solder pad layout operating temperature: -5 5 c to +1 5 0 c storage temperature: -5 5 c to +1 5 0 c maximum thermal resistance; 3 0 c/w junction to lead m cc catalog number device marking maximum rec urrent peak reverse voltage maximum rms voltage maximum dc blocking voltage u f s 11 0 100v 70v 100v u f s 11 5 150v 105v 150v u f s s 12 0 200v 140v 200v u f s 10 5 5 0v 5 0v 5 0v www. mccsemi .com 3 0 n s maximum reverse recovery time t rr i f = 0 . 5 a, i rr =0.25a om p on ent s 20736 marilla street chatsworth ! " # $ % ! " # mcc revision: 3 2003/04/30
u f s 1 0 5 thru u f s 12 0 average forward rectified current - amperes versus ambient temperature - c figure 2 forward derating curve 0 1 5 025 50 75 1 00 0 .2 .4 .6 .8 1.0 1.2 1.4 single phase, half wave 60hz resistive or inductive load amps c 1 2 5 1.6 1.8 2.0 2.2 2.4 instantaneous forward current - amperes versus instantaneous forward voltage - volts figure 1 typical forward characteristics 4 6 20 10 amps .2 .4 .6 .8 1.0 1.2 .01 .02 .04 .06 .1 .2 .4 .6 1 2 25 c volts figure 3 junction capacitance .1 .2 1 .4 2 10 20 404 100 200 1 2 6 10 20 100 junction capacitance - pf versus reverse voltage - volts pf volts 60 40 4 400 1000 t j =25 c mcc www. mccsemi .com revision: 3 2003/04/30
u f s 10 5 thru u f s 12 0 t rr +0.5a 0 -0.25 -1.0 1cm set time base for 20/100ns/cm 25vdc 1 w 50 w 10 w oscilloscope note 1 pulse generator note 2 notes: 1. rise time = 7ns max. input impedance = 1 megohm, 22pf 2. rise time = 10ns max. source impedance = 50 ohms 3. resistors are non-inductive figure 6 reverse recovery time characteristic and test circuit diagram 1 100 4 0 5 10 15 8 figure 4 peak forward surge current peak forward surge current - amperes versus number of cycles at 60hz - cycles amps cycles 2 6 10 20 60 80 40 20 25 3 5 mcc www. mccsemi .com revision: 3 2003/04/30
|