axk(5/6)l narrow-pitch connectors for board-to-board connection narrow pitch (0.5mm) connectors p5 series ?p5kl features 1. low pro?e mating height of 1.2 mm with 0.5 mm pitch, was obtained. it contributes to device compactness. 2. strong resistance to adverse environments! utilizes construction for high contact reliability. 1) contacts are highly resistant to shock caused by dropping and employ our original bellows contact construction. 2) v notch construction used for excellent resistance against foreign matters. 3) use of ni barrier construction is standard. highly effective against solder creeping. (available from nov. 2005) 4) porosity treatment applied for improved resistance against corrosion. 3. simple lock structure employed to further increase connection reliability 4. effective mating length 0.3 mm 5. compliance with rohs directive environmentally friendly, the connectors comply with europe s rohs directive. cadmium, lead, mercury, hexavalent, chromium, pbb and pbde are not used. applications ?cellular phones ?phs ?portable data terminals ?digital cameras ?compact portable devices socket header since the contact is formed by bending thin plate, it has a spring-like quality. this structure makes it resistant to dropping and twisting. what is v notch construction? by using the edge for the contacting part and increasing contact pressure per unit area, the effectiveness in removing flux and contaminants is increased compared to its predecessor. this is also effective in preventing the trapping of contaminants. [cross section of contacting part] without notch with v notch header side contact cross section socket side contact cross section what is ni barrier construction? by providing an exposed nickel part on the gold (au) plated contact, solder creeping is prevented despite the ultra low profile. header side contact [contact] socket side contact note: construction makes solder creeping difficult because header side is formed at the same time. ni barrier exposed ni part cu ni au cross section of socket side contact pinholes ni plating base material porosity treatment film what is porosity treatment? au plating surrounding gas this treatment consists of coating the surface with a very thin film to seal pinholes in the gold plating. this porosity treatment technology ensures the same contact reliability for thin gold plating as that of thick gold plating. improvement in insertion/removal durability improvement in resistance to corrosion improvement in contact reliability for digital signals simple lock 0.3mm 1.2mm pcb narrow-pitch connectors p5kl fpc reinforcing plate before mating ideal for board-to-fpc connections after mating the simple lock mechanism ensures that the connector clicks into position when it is inserted for reliable single-action insertion on the pcb. this enables the number of pins to be doubled white the size remains the same as that for existing fpc connectors. this, in turn, contributes to making products and equipment more compact. all rights rese r v ed c o p y r i gh t matsushita elect r ic w o r k s , ltd.
axk(5/6)l table of product types p5kl (0.5 mm pitch): without retention tting ordering information socket header 1.2mm mated height ? : available for sale 10 12 20 24 30 34 40 50 60 ? ? ? ? ? ? ? ? ? number of contacts notes: 1. the standard type comes with positioning bosses. connectors with positioning boss are available for on-demand production. 2. please consult us regarding numbers of contacts other than those given above. mated height 3: for mated height 1.2 mm 3: for mated height 1.2 mm surface treatment (contact portion / terminal portion) 5: ni plating on base, au plating on surface 7: ni plating on base, au plating on surface (for ni barrier product available from nov. 2005) number of contacts (2 digits) packing note) g: 3,000 pieces embossed tape and plastic reel 2 (for ni barrier product available from nov. 2005) j: 3,000 pieces embossed tape and paper reel 2 v: 3,000 pieces embossed tape and paper reel 5 note) for packaging, models without ni barrier only support j and v . models with ni barrier support only g . 5l: narrow pitch connector p5kl (0.5 mm pitch) socket 6l: narrow pitch connector p5kl (0.5 mm pitch) header functions 3: with positioning bosses 4: without positioning bosses axk all rights rese r v ed c o p y r i gh t matsushita elect r ic w o r k s , ltd.
axk(5/6)l product types notes) 1. regarding ordering units: during production, please make orders in 1-reel units. samples for mounting con?mation: please consult us. samples: small lot orders are possible. please consult us. 2. the standard type comes without positioning bosses. connectors with positioning bosses are available for on-demand production . for this type of connector, 9th digit of the part no. changes from 4 to 3. e.g. 10 contacts for sockets: axk5l1033 7g specifications 1. characteristics 2. material and surface treatment mated height no. of contacts part no. packing quantity socket header inner carton (1-reel) outer carton ni barrier product: not available (paper reel) (plastic reel) (recommendation) ni barrier product: not available (paper reel) (plastic reel) (recommendation) 1.2 mm 10 axk5l10345 ? axk5l10347g (from nov. 2005) axk6l10345 ? axk6l10347g (from nov. 2005) asterisk ? mark on end of part no.; j: 3,000 pieces v: 3,000 pieces ? mark on end of part no.; 3,000 pieces asterisk ? mark on end of part no.; j: 6,000 pieces (2-reel) v: 15,000 pieces (5-reel) ? mark on end of part no.; 6,000 pieces (2-reel) 12 axk5l12345 ? axk5l12347g (from nov. 2005) axk6l12345 ? axk6l12347g (from nov. 2005) 20 axk5l20345 ? axk5l20347g (from nov. 2005) axk6l20345 ? axk6l20347g (from nov. 2005) 24 axk5l24345 ? axk5l24347g (from nov. 2005) axk6l24345 ? axk6l24347g (from nov. 2005) 30 axk5l30345 ? axk5l30347g (from nov. 2005) axk6l30345 ? axk6l30347g (from nov. 2005) 34 axk5l34345 ? axk5l34347g (from nov. 2005) axk6l34345 ? axk6l34347g (from nov. 2005) 40 axk5l40345 ? axk5l40347g (from nov. 2005) axk6l40345 ? axk6l40347g (from nov. 2005) 50 axk5l50345 ? axk5l50347g (from nov. 2005) axk6l50345 ? axk6l50347g (from nov. 2005) 60 axk5l60345 ? axk5l60347g (from nov. 2005) axk6l60345 ? axk6l60347g (from nov. 2005) item speci?ations conditions electrical characteristics rated current 0.5a/contact (max. 10 a at total contacts) rated voltage 60v ac/dc breakdown voltage 150v ac for 1 minute detection current: 1ma insulation resistance min. 1,000m ? (initial) using 500v dc megger contact resistance max. 90m ? measured based on the hp4338b measurement method of jis c 5402 mechanical characteristics composite insertion force max. 0.981n {100gf}/contacts contacts (initial) composite removal force min. 0.0588n {6gf}/contacts contacts holding force of terminal securing section min. 0.981n {100gf}/contact measures the maximum load in the post axial direction until removal environmental characteristics ambient temperature ?5? to +85? no freezing at low temperatures soldering heat resistance max. peak temperature of 245? infrared re?w soldering 300? within 5 seconds 350? within 3 seconds soldering iron thermal shock resistance (header and socket mated) 5 cycles, insulation resistance min. 100m ? , contact resistance max. 90m ? sequence 1. ?5 c, 30 minutes 2. ~ , max. 5 minutes 3. 85 c, 30 minutes 4. ~ , max. 5 minutes humidity resistance (header and socket mated) 120 hours, insulation resistance min. 100m ? , contact resistance max. 90m ? bath temperature 40??, humidity 90 to 95% r.h. saltwater spray resistance (header and socket mated) 24 hours, insulation resistance min. 100m ? , contact resistance max. 90m ? bath temperature 35??, saltwarter concentration 5?% h 2 s resistance (header and socket mated) 48 hours, contact resistance max. 90m ? bath temperature 40??, gas concentration 3? ppm, humidity 75 to 80% r.h. lifetime characteristics insertion and removal life 50 times repeated insertion and removal speed of max. 200 times/hours unit weight 20 contacts; socket: 0.05g; header: 0.02g part name material surface treatment molded portion heat-resistant resin (ul94v-0), ivory white contact/post copper alloy contact portion: ni plating on base, au plating on surface terminal portion: ni plating on base, au plating on surface (except for thick of terminal) however, the area adjacent to the terminal on ni barrier models is exposed to ni on base. 0 ? +3 0 all rights rese r v ed c o p y r i gh t matsushita elect r ic w o r k s , ltd.
axk(5/6)l dimensions mm general tolerance: 0.2 ?socket and header are mated ?socket (mated height: 1.2mm) terminal coplanarity 0.10 4.20 (0.80)(0.80) 5.80 1.20 0.10 0.03 (suction face) 1.60 4.80 0.50 0.05 0.20 0.03 b 0.1 a 1.15 dimension table (mm) no. of contacts a b 10 5.50 2.00 12 6.00 2.50 20 8.00 4.50 24 9.00 5.50 30 10.50 7.00 34 11.50 8.00 40 13.00 9.50 50 15.50 12.00 60 18.00 14.50 ?header (mated height: 1.2mm) terminal coplanarity 0.10 0.90 a b 0.1 (suction face) 1.20 2.50 0.50 0.05 0.20 0.03 0.10 0.03 3.30 2.00 (0.65) (0.65) 0.95 dimension table (mm) no. of contacts a b 10 3.90 2.00 12 4.40 2.50 20 6.40 4.50 24 7.40 5.50 30 8.90 7.00 34 9.90 8.00 40 11.40 9.50 50 13.90 12.00 60 16.40 14.50 socket header 1.20 0.15 all rights rese r v ed c o p y r i gh t matsushita elect r ic w o r k s , ltd.
axk(5/6)l embossed tape dimensions (unit:mm, common for respective contact type, socket and header) dimension table (mm) (1) suf?: g (1 reel, 3,000 pieces embossed tape: plastic reel package) ... from nov. 2005 (2) suf?: j, v (1 reel, 3,000 pieces embossed tape: paper reel package) connector orientation with respect to direction of progress of embossed tape mated height no. of contacts type of taping a b c d e f quantity per reel socket and header are common: 1.2mm 10 to 18 tape i 16.0 7.5 8.0 17.4? 380 dia. 3,000 pcs. 20 to 50 tape i 24.0 11.5 8.0 25.4? 380 dia. 3,000 pcs. 60 tape ii 32.0 28.4 14.2 8.0 33.4? 380 dia. 3,000 pcs. mated height no. of contacts type of taping a b c d e f quantity per reel socket and header are common: 1.2mm 10 to 18 tape i 16.0 7.5 8.0 16.4 370 dia. 3,000 pcs. 20 to 50 tape i 24.0 11.5 8.0 24.4 370 dia. 3,000 pcs. 60 tape ii 32.0 28.4 14.2 8.0 32.4 370 dia. 3,000 pcs. tape dimensions (conforming to jis c 0806-1990. however, some tapes have mounting hole pitches that do not comply with the standard.) tape i tape ii 1.75 c d a 0.3 4 2 1.5 dia. +0.1 0 pull out direction 1.75 c d a 0.3 4 2 pull out direction b 1.5 dia. +0.1 0 plastic reel dimensions (conforming to eiaj et-7200b)/ paper reel dimensions (conforming to jis c 0806-1990) f e top cover tape emboss carrier tape +2 0 +2 0 +2 0 type direction of tape progress common for p5kl socket header note: there is no indication on this product regarding top-bottom or left-right orientation. all rights rese r v ed c o p y r i gh t matsushita elect r ic w o r k s , ltd.
axk(5/6)l notes 1. as shown below, excess force during insertion may result in damage to the connector or removal of the solder. please be careful. also, to prevent connector damage plese con rm the correct position before mating connectors. 2. keep the pc board warp no more than 0.03 mm in relation to the overall length of the connector. 3. pc boards and recommended metal mask patterns connectors are mounted with high density, with a pitch interval of 0.4 to 0.5 mm. it is therefore necessary to make sure that the right levels of solder are used, in order to reduce solder bridge and other issues. the ?ures to the right are recommended metal mask patterns. please use them as a reference. socket reconnended pc board pattern (top view) recommended metal mask pattern metal mask thickness: 150 ? (terminal portion opening area ratio: 57%) recommended metal mask pattern metal mask thickness: 120 ? (terminal portion opening area ratio: 70%) header reconnended pc board pattern (top view) recommended metal mask pattern metal mask thickness: 150 ? (terminal portion opening area ratio: 56%) recommended metal mask pattern metal mask thickness: 120 ? (terminal portion opening area ratio: 70%) max. 0.03mm max. 0.03mm 0.50 0.05 0.25 0.03 4.00 0.05 6.80 0.05 b 0.05 0.125 0.03 2.20 0.05 3.20 0.05 c 0.40 0.05 : non-insulated area where through holes are prohibited 0.115 0.01 (0.86) (0.86) 0.50 0.01 0.35 0.01 0.23 0.01 6.60 0.01 4.88 0.01 0.35 0.01 0.115 0.01 (1.07) (1.07) 4.46 0.01 6.60 0.01 0.23 0.01 0.50 0.01 regarding general notes, please refer to page 12. for other details, please verify with the product speci?ation sheets. 0.25 0.03 0.50 0.05 0.125 0.03 0.40 0.05 2.40 0.05 4.30 0.05 b 0.05 0.23 0.01 0.50 0.01 0.115 0.01 0.35 0.01 4.10 0.01 2.94 0.01 (0.58) (0.58) 0.50 0.01 0.23 0.01 0.35 0.01 0.115 0.01 4.10 0.01 2.66 0.01 (0.72) (0.72) all rights rese r v ed c o p y r i gh t matsushita elect r ic w o r k s , ltd.
|
