14 pin dip and smd 5 tap low-profile ttl compatible active delay lines delays are 5% or 2 ns? tap 5, 10, 15, 20 6, 12, 18, 24 7, 14, 21, 28 8, 16, 24, 32 9, 18, 27, 36 10, 20, 30, 40 12, 24, 36, 48 15, 30, 45, 60 20, 40, 60, 80 25, 50, 75, 100 30, 60, 90, 120 35, 70, 105, 140 total 25 30 35 40 45 50 60 75 100 125 150 175 dip part number ep8200-hl ep8213-hl ep8214-hl ep8215-hl ep8216-hl ep8201-hl ep8211-hl ep8217-hl ep8202-hl ep8219-hl ep8203-hl ep8220-hl smd part number epa073hl-25 epa073hl-30 epa073hl-35 epa073hl-40 epa073hl-45 epa073hl-50 epa073hl-60 epa073hl-75 epa073hl-100 epa073hl-125 epa073hl-150 epa073hl-175 delays are 5% or 2 ns? tap 40, 80, 120, 160 45, 90, 135, 180 50, 100, 150, 200 60, 120, 180, 240 70, 140, 210, 280 80, 160, 240, 320 84, 168, 252, 336 88, 176, 264, 352 90, 180, 270, 360 84, 188, 282, 376 100, 200, 300, 400 total 200 225 250 300 350 400 420 440 450 470 500 dip part number ep8204-hl ep8221-hl ep8205-hl ep8206-hl ep8207-hl ep8208-hl ep8218-hl ep8222-hl ep8209-hl ep8223-hl ep8210-hl smd part number epa073hl-200 epa073hl-225 epa073hl-250 epa073hl-300 epa073hl-350 epa073hl-400 epa073hl-420 epa073hl-440 epa073hl-450 epa073hl-470 epa073hl-500 ? whichever is greater. delay times referenced from input to leading edges at 25c, 5.0v, with no load. compatible with standard auto-insertable equipment and can be used in either infrared or vapor phase process. schematic v oh high-level output voltage v cc = min. v il = max. i oh = max 2.7 v v ol low-level output voltage v cc = min. v ih = min. i ol = max 0.5 v v ik input clamp voltage v cc = min. i i = ii k -1.2 v i ih high-level input current v cc = max. v in = 2.7v 50 a v cc = max. v in = 5.25v 1.0 ma i il low-level input current v cc = max. v in = 0.5v -2 ma i os short circuit output current v cc = max. v out = 0. -40 -100 ma (one output at a time) i cch high-level supply current v cc = max. v in = open 75 ma i ccl low-level supply current v cc = max. v in = 0 75 ma t ro output rise time td 500 ns (0.75 to 2.4 volts) 4 ns td > 500 ns 5 ns n h fanout high-level output v cc = max. v oh = 2.7v 20 ttl load n l fanout low-level output v cc = max. v ol = 0.5v 10 ttl load dc electrical characteristics parameter test conditions min max unit e in pulse input voltage 3.2 volts p w pulse width % of total delay 110 % t ri pulse rise time (0.75 - 2.4 volts) 2.0 ns p rr pulse repetition rate @ td 200 ns 1.0 mhz pulse repetition rate @ td > 200 ns 100 khz v cc supply voltage 5.0 volts input pulse test conditions @ 25 c unit v cc supply voltage 4.75 5.25 v v ih high-level input voltage 2.0 v v il low-level input voltage 0.8 v i ik input clamp current -18 ma i oh high-level output current -1.0 ma i ol low-level output current 20 ma p w * pulse width of total delay 40 % d* duty cycle 40 % t a operating free-air temperature 0 +70 c recommended operating conditions min max unit *these two values are inter-dependent. unless otherwise noted dimensions in inches tolerances: fractional = 1/32 .xx = .030 .xxx = .010 16799 schoenborn st. north hills, ca 91343 tel: (818) 892-0761 fax: (818) 894-5791
|
