d s - 5 1 5 2 r e v 0 0 2 008 - 0 9 -27 preliminary datasheet SPP-10E-LM-CDFA features z support 10gbase-lr m application z up to 220m transmission in mmf z 1310nm fp laser and pin receiver with linear amplifier z sfi high speed electrical interface z 2-wire interface with integrated digital diagnostic monitoring z sfp+ msa package with duplex lc connector z single +3.3v power supply z power consumption less than 1.5 w z operating case temperature: -5~+70c regulatory compliance table 1 - regulatory compliance feature standard performance electrostatic discharge (esd) to the electrical pins mil-std-883e method 3015.7 class 1(>1000v for sfi pins, >2000v for other pins.) electrostatic discharge (esd) to the duplex lc receptacle iec 61000-4-2 gr-1089-core compatible with standards electromagnetic interference (emi) fcc part 15 class b en55022 class b (cispr 22b) vcci class b compatible with standards immunity iec 61000-4-3 compatible with standards laser eye safety fda 21cfr 1040.10 and 1040.11 en60950, en (iec) 60825-1,2 compatible with class i laser product. rohs 2002/95/ec 4.1&4.2 2005/747/ec compliant with standards note note: in light of item 5 in annex of 2002/ 95/ec, ?pb in the glass of cathode ray tubes, electronic components and fluorescent tubes.? and item 13 in annex of 2005/747/ ec, ?lead and cadmium in optical and filter glass.?, the two exemptions are being concerned for source p hotonics transceivers, because source photonics transceivers use glass, which may contain pb, for co mponents such as lenses, windows, isolators, and other electronic components.
d s - 5 1 5 2 r e v 0 0 2 008 - 0 9 -27 preliminary datasheet SPP-10E-LM-CDFA absolute maximum ratings table 2 - absolute maximum ratings parameter symbol min. typical max. unit notes storage temperature t s -40 - +85 c supply voltage v cc -0.5 - +4.0 v operating relative humidity rh - - +85 % recommended operating conditions table 3 ? recommended operating conditions parameter symbol min. typical max. unit notes operating case temperature t c -5 - +70 c power supply voltage v cc 3.14 3.3 3.46 v power supply current i cc - - 430 ma power dissipation p d - - 1.5 w bit rate br - 10.3125 - gbps transmission distance td 2 - 220 m 1 note 1: measured with mmf. optical characteristics table 4 ? optical characteristics transmitter parameter symbol min. typical max. unit notes center wavelength range c 1260 - 1355 nm average output power p 0ut -6.5 - 0.5 dbm 1 optical modulation amplitude oma -4.5 - 1.5 dbm 1 average output power (laser off) p 0ut-off - - -30 dbm 1 extinction ratio er 3.5 - - db 2 rms spectral width - - 4 nm transmitter waveform and dispersion penalty twdp - - 4.7 db optical return loss tolerance orlt - - 20 db optical eye mask compliant with ieee 802.3aq-2006 2 receiver center wavelength range c 1260 - 1355 nm stress sensitivity in oma p in-oma -6.5 dbm 3
d s - 5 1 5 2 r e v 0 0 2 008 - 0 9 -27 preliminary datasheet SPP-10E-LM-CDFA stressed sensitivity in oma for symmetrical test p in-oma -6 dbm 3 overload in oma p in-oma 1.5 dbm 3 received average power for damage p in-damage 1.5 dbm receiver reflectance -12 db notes: 1. the optical power is launched into smf. 2. measured with a prbs 2 31 -1 test pattern @10.3125gbps. 3. measured with a prbs 2 31 -1 test pattern @10.3125gbps, ber 10 -12 . electrical characteristics table 5 ? electrical characteristics transmitter parameter symbol min. typical max. unit notes differential data input amplitude v in,p-p 180 - 700 mvpp input differential impedance z in 85 100 115 ? normal operation v ol -0.3 - 0.4 v tx_fault transmitter fault v oh 2.4 - v cc v normal operation v il -0.3 - 0.8 v tx_disable laser disable v ih 2.0 - v cc +0.3 v receiver differential data output amplitude v out,p-p 120 - 600 mvpp output differential impedance z o 80 100 120 ? output rise time, 20%~80% t r 28 - - ps output fall time, 20%~80% t f 28 - - ps
d s - 5 1 5 2 r e v 0 0 2 008 - 0 9 -27 preliminary datasheet SPP-10E-LM-CDFA recommended host board power supply circuit figure 1, recommended host board power supply circuit recommended interface circuit figure 2, recommended interface circuit
d s - 5 1 5 2 r e v 0 0 2 008 - 0 9 -27 preliminary datasheet SPP-10E-LM-CDFA pin definitions figure 3, pin view table 6?pin function definitions pin logic symbol name/description note 1 v ee t module transmitter ground 1 2 lvttl-o tx_f ault module transmitter fault 2 3 lvttl-i tx_disable transmitter disable; turns off transmitter laser output 3 4 lvttl-i/o sdl 2-wire serial interface data line (mod-def2) 5 lvttl-i/o scl 2-wire serial interface clock (mod-def1) 6 mod_abs module absent, connected to v ee t or v ee r in the module 2 7 lvttl-i rs0 rate select 0, not implement 4 8 lvttl-o rx_los receiver loss of signal indication (in fc designated as rx_los, in sonet designated as los, and in ethernet designated as not signal detect) 2 9 lvttl-i rs1 rate select 1, not implement 4 10 v ee r module receiver ground 1 11 v ee r module receiver ground 1 12 cml-o rd- receiver inverted data output 13 cml-o rd+ receiver non-inverted data output 14 v ee r module receiver ground 1 15 v cc r module receiver 3.3 v supply 16 v cc t module transmitter 3.3 v supply 17 v ee t module transmitter ground 1 18 cml-i td+ transmitter non-inverted data input 19 cml-i td- transmitter inverted data input 20 v ee t module transmitter ground 1
d s - 5 1 5 2 r e v 0 0 2 008 - 0 9 -27 preliminary datasheet SPP-10E-LM-CDFA notes: 1. the module ground pins are isolated from the module case. 2. the pins shall be pulled up with 4.7k-10kohms to a voltage between 3.14v and 3.46v on host board. 3. the pin is pulled up to v cc t with a 4.7k-10k ? resistor in the module. 4. the pins are pulled low to v ee t with a >30k ? resistor in the module. eeprom information figure 4, 2-wire serial digital diagnostic memory map table 7 ? digital diagnostic specification (a2h) data address parameter range accuracy 96-97 temperature -10 to +80c 3c 98-99 v cc voltage +3.0v to +3.7v 3% 100-101 tx bias current 0 to 100ma 10% 102-103 tx output power -7 to +1dbm 3db 104-105 rx input power -15 to +1dbm 3db
d s - 5 1 5 2 r e v 0 0 2 008 - 0 9 -27 preliminary datasheet SPP-10E-LM-CDFA table 8 ?eeprom serial id memory contents (a0h) addr. bytes name of field hex description 0 1 identifier 03 sfp 1 1 ext. identifier 04 sfp with serial id 2 1 connector 07 lc 3-10 8 transceiver 40 00 00 00 00 00 00 00 10gbase-lrm 11 1 encoding 03 nrz 12 1 br, nominal 67 10.3g 13 1 rate identifier 00 not specified 14 1 length (9um)-km 00 15 1 length (9um) 00 16 1 length (50um, om2) 16 220m 17 1 length (62.5um,om1) 16 220m 18 1 length (copper) 00 19 1 length (50um, om3) 16 220m 20-35 16 vendor name 53 4f 55 52 43 45 50 48 4f 54 4f 4e 49 43 53 20 ?sourcephotonics ?(asc ) 36 1 reserved 00 37-39 3 vendor oui 00 00 00 not specified 40-55 16 vendor pn 53 50 50 31 30 45 4c 4d 43 44 46 41 20 20 20 20 ?spp10elmcdfa? (asc ) 56-59 4 vendor rev xx xx xx xx asc 60-61 2 wavelength 05 1e 1310nm 62 1 reserved 00 63 1 cc base xx check sum of bytes 0-62 64-65 2 options 02 3a table 3.7 of sff-8472, rev 10.3 66 1 br, max 00 not specified 67 1 br, min 00 not specified 68-83 16 vendor sn xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx asc 84-91 8 vendor date code xx xx xx xx xx xx 20 20 year (2 bytes), month (2 bytes), day (2 bytes) 92 1 diagnostic type 68 diagnostics (internally calibrated) 93 1 enhanced option fa table 3.10 of sff-8472, rev 10.3 94 1 sff-8472 compliance 03 sff-8472 rev 10 compliant 95 1 cc_ext xx check sum of bytes 64-94 96-255 160 vendor specific reserved by vendor
d s - 5 1 5 2 r e v 0 0 2 008 - 0 9 -27 preliminary datasheet SPP-10E-LM-CDFA mechanical diagram figure 5, mechanical diagram of sfp+ order information table 9 ? order information part no. application data rate laser source fiber type SPP-10E-LM-CDFA 10gbase-lrm 10.3125g 1310nm fp smf warnings handling precautions: this device is susceptible to damage as a result of electrostatic discharge (esd). a static free environment is highly recommended. foll ow guidelines according to proper esd procedures. laser safety: radiation emitted by laser devices can be dangerous to human eyes. avoid eye exposure to direct or indirect radiation. legal notice important notice! all information contained in this document is subject to change without notice, at source photonics?s sole and absolute discretion. source photonics warrants perfo rmance of its products to current specifications only in accordance with the company?s standard one-y ear warranty; however, specifications designated as ?preliminary? are given to describe components only, and source photonics expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of
d s - 5 1 5 2 r e v 0 0 2 008 - 0 9 -27 preliminary datasheet SPP-10E-LM-CDFA merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. please refer to the company?s terms and conditions of sa le for further warranty information. source photonics assumes no liability for applications assistance, customer pr oduct design, software performance, or infringement of patents, services, or intellectual property described herein. no license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and source photonics makes no representations or warrant ies that the product(s) described herein are free from patent, copyright, or intellectual property ri ghts. products described in this document are not intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. source photonics cu stomers using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnif y source photonics for any damages resulting from such use or sale. the information contained in this document is provided on an ?as is? basis. customer agrees that source photonics is not liable for any actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. customer must contact source photonics to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current. contact u.s.a. headquarters 20550 nordhoff street chatsworth, ca 91311 usa tel: +1-818-773-9044 fax: +1-818-773-0261 china building #2&5, west export processing zone no. 8 kexin road, hi-tech zone chengdu, 611731, china tel: +86-28-8795-8788 fax: +86-28-8795-8789 taiwan 9f, no 81, shui lee rd. hsinchu, taiwan, r.o.c. tel: +886-3-5169222 fax: +886-3-5169213 ? copyright source photonics, inc. 2007~2008 all rights reserved
|
