world products inc. electr onic component solutions 19654 eighth street east, sonoma, ca 95476-0517 usa ?phone (707) 996-5201 ?f ax (707) 996-3380 www .w orldpr oducts.com micro inductors revised 05/06/05
world products inc. 19654 eighth street east, sonoma, ca 95476, phone (707) 996-5201, fax (707) 996-3380 www.worldproducts.com 050605 rev.9.0 1 micro inductors features 1. very high self-resonant frequencies 2. ultra miniature size (0.6mm x 0.3mm x 0.3mm) and low weight. 3. no polarity 4. terminal electrode has excellent so lder heat resistance for soldering. 5. elimination of leads. 6. rohs compliant with directive 2002/95/ec of the european pa rliament and of the council of 27 january 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (rohs directive) and comply to a maximum concentration valu e of 0.1% by weight in homogeneous materials for lead (p b), mercury, hexavalent chromium, polybr ominated biphenyls (pbb) and polybrominat ed diphenyl ethers (pbde) and of 0.01% wei ght in homogeneous materials for cadmium. applications 1. bluetooth module 2. cdma, tdma, gsm, pcs phone 3. rf module of telecommunication products. - cellular phone, cordless telephone, pagers etc. 4. pam (power amp module) 5. computer communications, radar detectors. ordering information wpm - 0603 - 22 j t (1) (2) (3) (4) (5) (1) series wpm: micro inductors (2) dimensions* first two digits: length (mm) last two digits: width (mm) (3) inductance nh value (4) tolerance s: 0.3nh j: 5% (5) packaging b: bulk package t: tape & reel ( 178mm [7 inches]) l: tape & reel ( 254mm [10 inches]) *0603(mm) is equivalent to 0201 (inches). 1005(mm) is equivalent to 0402 (inches). shape and dimensions type l w t c 1 wpm-0603 0.60.03 [.024.001] 0.30.03 [.012.001] 0.30.03 [.012.001] 0.150.05 [.006.002] wpm-1005 1.00.05 [.039.002] 0.50.05 [0.20.002] 0.50.05 [.0200.02] 0.200.10 [.008.004] w t l c 1
world products inc. 19654 eighth street east, sonoma, ca 95476, phone (707) 996-5201, fax (707) 996-3380 www.worldproducts.com 050605 rev.9.0 2 micro inductors specifications 0603 series inductance (at 100mhz) q (min) q(typ) srf(ghz) dcr( ? ) part no. nh tolerance 100mhz 100mhz 800mhz 1000mhz min. max. rated current (ma) max. wpm-0603-1.0s 1.0 3 4.0 13.3 15.0 19.0 0.20 400 wpm-0603-1.2s 1.2 3 4.0 13.3 15.0 19.0 0.25 400 wpm-0603-1.5s 1.5 3 4.0 13.2 14.8 18.0 0.30 400 wpm-0603-1.8s 1.8 3 4.1 13.2 14.6 17.0 0.35 400 wpm-0603-2.2s 2.2 3 4.1 13.0 14.5 15.0 0.40 400 wpm-0603-2.7s 2.7 3 4.1 13.0 14.5 14.0 0.45 350 wpm-0603-3.3s 3.3 3 4.2 12.8 14.3 13.0 0.50 350 wpm-0603-3.9s 3.9 3 4.2 12.8 14.2 12.0 0.55 350 wpm-0603-4.7s 4.7 3 4.2 12.6 14.2 10.0 0.60 350 wpm-0603-5.6s 5.6 .0.3nh 3.5 4.3 12.5 14.0 10.0 0.70 350 wpm-0603-6.8j 6.8 3.5 4.3 12.5 14.0 9.0 0.80 300 wpm-0603-8.2j 8.2 3.5 4.5 12.7 14.0 8.0 0.90 300 wpm-0603-10j 10 3.5 4.8 13.0 14.3 8.0 1.00 250 wpm-0603-12j 12 4 4.8 12.0 13.5 7.0 1.10 250 wpm-0603-15j 15 4 4.7 11.5 13.0 6.0 1.20 200 wpm-0603-18j 18 4 4.5 11.0 12.0 5.0 1.40 200 wpm-0603-22j 22 5% 4 4.5 10.2 11.0 5.0 1.60 150 test equipment & fixture l, q : rf impedance analyzer 4991a(agilent) , test fixture 16196c(agilent) srf : network analyzer 8722es (agilent) rdc : twa-161a,b electrical characteristics inductance vs. frequency q vs. frequency 10m 100m 1g 10g 0 10n 20n 30n 1.0nh 5.6nh 10nh 22nh l(h) frequency (hz) 10m 100m 1g 10g 0 5 10 15 20 25 1.0nh 5.6nh 10nh 22nh q frequency (hz)
world products inc. 19654 eighth street east, sonoma, ca 95476, phone (707) 996-5201, fax (707) 996-3380 www.worldproducts.com 050605 rev.9.0 3 micro inductors specifications 1005 series inductance (at 100mhz) q (min) q(typ) srf(ghz) dcr( ? ) part no. nh tolerance 100mhz 100mhz 800mhz 1000mhz min. max. rated current (ma) max. wpm-1005-1.0s 1.0 4.0 8.0 20.5 23.7 20.0 0.10 300 wpm-1005-1.2s 1.2 4.0 8.4 21.2 24.9 20.0 0.15 300 wpm-1005-1.5s 1.5 4.0 8.4 21.2 25.4 14.0 0.20 300 wpm-1005-1.8s 1.8 4.0 9.2 21.5 26.9 13.0 0.20 300 wpm-1005-2.2s 2.2 4.0 8.6 22.2 26.8 12.0 0.23 300 wpm-1005-2.7s 2.7 4.5 8.4 22.8 26.0 10.0 0.25 250 wpm-1005-3.3s 3.3 5.0 9.0 22.2 26.5 10.0 0.25 250 wpm-1005-3.9s 3.9 5.0 9.2 23.1 26.6 10.0 0.30 250 wpm-1005-4.7s 4.7 5.5 9.6 23.2 26.9 8.0 0.35 250 wpm-1005-5.6s 5.6 .0.3nh 5.5 8.8 23.3 27.0 7.0 0.35 250 wpm-1005-6.8j 6.8 5.5 8.5 21.3 27.1 6.5 0.40 200 wpm-1005-8.2j 8.2 5.5 9.1 22.7 27.2 5.6 0.50 200 wpm-1005-10j 10 5.5 8.3 22.5 27.5 5.4 0.50 200 wpm-1005-12j 12 7.0 8.6 24.1 27.4 4.1 0.50 200 wpm-1005-15j 15 7.0 8.9 22.4 28.5 4.0 0.60 200 wpm-1005-18j 18 7.0 9.3 24.6 30.4 3.7 0.70 200 wpm-1005-22j 22 7.0 8.7 23.4 26.2 3.5 0.75 200 wpm-1005-27j 27 7.0 9.0 26.5 30.2 3.4 0.80 200 wpm-1005-33j 33 7.0 8.6 24.8 28.0 3.2 1.00 200 wpm-1005-39j 39 7.0 9.1 24.1 26.1 2.5 1.10 100 wpm-1005-47j 47 7.0 8.7 24.6 26.5 2.4 1.20 100 wpm-1005-56j 56 7.0 9.0 24.5 25.8 2.3 1.40 100 wpm-1005-68j 68 7.0 10.1 25.5 27.7 2.2 1.60 100 wpm-1005-82j 82 7.0 10.3 24.5 25.9 2.1 1.80 100 wpm-1005-100j 100 5% 7.0 9.2 23.2 24.2 2.0 2.00 100 test equipment & fixture l, q : rf impedance analyzer 4991a(agilent) , test fixture 16193a(agilent) srf : network analyzer 8722es (agilent) , rdc : twa-161a,b electrical characteristics inductance vs frequency q vs frequency 10m 100m 1g 10g 1n 10n 15nh 1.5nh 6.8nh 27nh l(h) frequency (hz) 10m 100m 1g 10g 0 10 20 30 40 50 60 70 1.5nh 6.8nh 15nh 27nh q frequency (hz)
world products inc. 19654 eighth street east, sonoma, ca 95476, phone (707) 996-5201, fax (707) 996-3380 www.worldproducts.com 050605 rev.9.0 4 micro inductors reliability and test conditions item requirements test condition operating temp. range -55 c~+125 c - storage temp. & humidity range -40 c max. , 70% rh max. at packing condition resistance to solder heat 1.no damage such as cracks should be visible in chip element. 2.more than 75% of the terminal electrode shall be covered with new solder. 3.inductance change : within 5% 4.quality factor change : within 30% preheat temperature : 100 to 150 c preheat time : 1min solder temperature : 260 10 c dipping time : 10 0.5sec. solderability 1.more than 90% of the terminal electrode shall be covered with new solder. 2.inductance change : within 5% 3.quality factor change : within 30% preheat temperature : 100 to 150 c preheat time : 1min solder temperature : 230 10 c dipping time : 3 1sec. reflow soldering 1.more than 50% of the terminal electrode shall be covered with new solder. t s s t * 0.5 preheat temperature : 150 c preheat time : 1min solder temperature : 230 c soldering time : 10 sec. max. (reflow soldering profile) bending test 1.no mechanical damage. r230 l20 45 45 0.8 1.5
world products inc. 19654 eighth street east, sonoma, ca 95476, phone (707) 996-5201, fax (707) 996-3380 www.worldproducts.com 050605 rev.9.0 5 micro inductors item requirements test condition drop 1.no mechanical damage. drop 10 times on a concrete floor from a height of 91cm vibration 1.no mechanical damage. frequency: 10~55~10hz amplitude: 1.52mm direction and time: x,y,z directions for 2 hours thermal shock (temperature cycle) 1.no mechanical damage. 2.inductance change: within 5% 3.quality factor change: within 30% step1. ?40 3 c 30 3min. step2. 85 3 c 30 3min. number of cycle: 100 times heat load resistance 1.no mechanical damage. 2.inductance change: within 5% 3.quality factor change: within 30% temperature: 85 2 c applied current: rated current time: 1,000 hours measured at ambient temperature after placing for 24 hours low temp. resistance 1.no mechanical damage. 2.inductance change: within 5% 3.quality factor change: within 30% temperature: -40 5 c time: 1,000 hours measured at ambient temperature after placing for 24 hours humidity resistance 1.no mechanical damage. 2.inductance change: within 5% 3.quality factor change: within 30% temperature: 40 2 c humidity: 90~95% rh time: 500 hours measured at ambient temperature after placing for 24 hours humidity load resistance 1.no mechanical damage. 2.inductance change: within 5% 3.quality factor change: within 30% temperature: 40 2 c applied current: rated current time: 500 hours measured at ambient temperature after placing for 24 hours land pattern design a b a c labeling label 1) part name. 2) lot no. 3) quantity. standard quantity for packing (pcs) tape & reel bulk packing type(eia) reel inner box carton box vinyl or cassette 0603 10,000 100,000 400,000 1005 10,000 100,000 400,000 as requested *packing method can be changed upon request. unit:mm size a b c 0603 0.22 0.25 0.32 1005 0.7 0.4 0.5
world products inc. 19654 eighth street east, sonoma, ca 95476, phone (707) 996-5201, fax (707) 996-3380 www.worldproducts.com 050605 rev.9.0 6 micro inductors tape dimensions paper unit: mm type a 0.1 b 0.1 p 0.1 t (max.) 0603 0.370.02 0.670.02 4.00.1 0.45 1005 0.650.1 1.150.1 2.00.1 0.8 leader and blank portion the pitch holes shift within 0.3 L for cumulative 10 pitches. reel dimensions type w (mm) 0603, 1005 9.0 0.3 10 to 20 pitches 20 to 40 pitches 210 to 250mm leader drawing direction chips blank blank 8.0 0.3 p a b t 2.0 0.05 4.0 0.1 chip cavity sprocket hole 1.5 + 0.1, - 0 1.75 0.1 3.5 0.05 unit : mm less than 1.5 r1.0 2.0 0.8 178 2.0 254 2.0 21.0 0.8 unit : mm 13.0 0.5 more than 50 w
world products inc. 19654 eighth street east, sonoma, ca 95476, phone (707) 996-5201, fax (707) 996-3380 www.worldproducts.com 050605 rev.9.0 7 micro inductors top cover tape strength the force for tearing off top cover tape is 20 to 70 grams in the arrow direction. soldering profile reflow soldering(peak 230c) reflow soldering (peak 250c) flo w soldering manual soldering 300 200c 230c 150c 0 50 100 150 200 250 60 sec. min. 20 sec. max. soldering 10 sec. max. cooling 60 sec. min. 250c 220c 190c 150c 0 50 100 150 200 250 300 350 100 sec. min. 60 sec. max. soldering 10 sec. max. 175c 250c 150c 0 50 100 150 200 60 sec. min. dipping 10 sec. max. cooling 60 sec. min. preheating 100 sec. max. top cover tape 165 to 180 embossing tape ? t 200c/ .5 sec 300c tcc soldering 2 sec max. solder iron 30w max. diameter of solder iron 1.2mm max. 180c
world products inc. 19654 eighth street east, sonoma, ca 95476, phone (707) 996-5201, fax (707) 996-3380 www.worldproducts.com 050605 rev.9.0 8 micro inductors precaution for product storage electrical characteristics of pr oduct will not change when stored under typical environmental conditions. however, it is possible that the solderability of the terminal electrodes and the characteristi cs of the tape packaging can cha nge during storage. for this reasons, the following st orage guidelines should be followed. storage environment the tape packaging material is designed to wi thstand long-term storage but it may degrade more rapidly in the presence of high temperature or high humidity. therefore, product shall be stored in an ambient temperature of less than 40c with a relative humidity of less than 70 . the products should be used within 6 months of receipt. to achieve best solderability, product s hould be used as soon as possible after unpacki ng. leftover product must be stored in dry condition with desiccant. corrosive gases since sulfur and chlorine may degrade the solderability of the term inal electrodes, it is important to store the product in an environment free of such gases. temperature fluctuations dew condensation may occur when the product is taken out of stora ge due to variation of temperature. it is important to mainta in a temperature-controlled environment. disclaimer: the names of the products and the specifications in this catalog are subject to change without notice for the sake of improvement. world products inc. also reserves the right to discontinue any of these products. the products in this catalog are intended for use in ordinary electronic products. if any of these products are to be used in special applications requiring extremely high reliability, where product defects might pose a safety risk, please consult world products inc. though world p roducts inc. has taken all possible precautions to ensure the quality and reliability of its products, impro per use of products may result in bodily injury, fire, or similar accident. if y ou have any questions regarding the use of the products in question, please consult world products inc. please be advised that world products inc. accepts no responsibility for any infraction by users o f world products inc. products on third party patents or industrial copyrights.
|
